Ryan Mallon [Sun, 5 Jun 2011 07:21:22 +0000 (07:21 +0000)]
Add support for Bluewater Systems Snapper 9260/9G20 modules
Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Jens Scharsig [Sat, 19 Feb 2011 06:17:02 +0000 (06:17 +0000)]
update arm/at91rm9200 work with rework rework110202
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
* Fix: timer.c compile error io.h not found with arm/at91rm9200
* update arm920t/at91 to ATMEL_xxx name scheme
* update arm920t/at91 soc lib
* update at91_emac driver
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
Fabio Estevam [Wed, 15 Jun 2011 03:36:23 +0000 (03:36 +0000)]
mx31pdk: Add DHCP command
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Helmut Raiger [Wed, 15 Jun 2011 01:45:45 +0000 (01:45 +0000)]
mxc_spi.c: typo fixed
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Fabio Estevam [Sat, 11 Jun 2011 15:16:11 +0000 (15:16 +0000)]
imx31_phycore: Fix build by using new relocation scheme
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Sat, 11 Jun 2011 15:16:32 +0000 (15:16 +0000)]
mx1ads: Fix build by using new relocation scheme
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Thu, 9 Jun 2011 14:43:26 +0000 (16:43 +0200)]
MX31: QONG: drop config.mk
Remove obsolete config.mk from QONG board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Aneesh V [Thu, 9 Jun 2011 12:54:57 +0000 (08:54 -0400)]
omap730p2: fix build breaks
Provide SDRAM base address and use SRAM for initial stack
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 9 Jun 2011 12:54:55 +0000 (08:54 -0400)]
omap2420h4: fix build breaks
DRAM base address and use SRAM for initial stack
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 9 Jun 2011 12:54:53 +0000 (08:54 -0400)]
omap1610inn: fix build breaks
Provide SDRAM base address and use SRAM for initial stack
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 9 Jun 2011 12:54:51 +0000 (08:54 -0400)]
omap1510inn: fix build breaks
Provide SDRAM base address and use SRAM for initial stack
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 9 Jun 2011 12:54:48 +0000 (08:54 -0400)]
omap5912osk: fix build breaks
Provide SDRAM base address and use SRAM for initial stack
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 9 Jun 2011 12:54:45 +0000 (08:54 -0400)]
omap1610h2: fix build breaks
Provide SDRAM base address and use SRAM for initial stack
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Timur Tabi [Wed, 8 Jun 2011 17:10:49 +0000 (12:10 -0500)]
powerpc/p1022ds: set the clock-frequency prop only if the clock is enabled
The clock-frequency property in an audio codec's device tree node is set to
the input clock frequency for that codec. On the Freescale P1022DS board,
the input clock is enabled only if the hwconfig 'audclk' option is set.
Therefore, the property should only be set in the device tree if the clock
is actually enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Wed, 8 Jun 2011 21:29:04 +0000 (23:29 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
SMDK6400: fix the compiler error
imx27lite: Remove local config.mk
mx31ads: Fix environment location on flash
imx31_litekit: Remove local config.mk
mx31litekit: Fix boot with the new relocation scheme.
mx31ads: Use the new relocation scheme
Minkyu Kang [Thu, 2 Jun 2011 21:27:01 +0000 (21:27 +0000)]
SMDK6400: fix the compiler error
This patch adds _end for fix following compiler error
arch/arm/cpu/arm1176/start.o: In function `_end_ofs':
arch/arm/cpu/arm1176/start.S:61: undefined reference to `_end'
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fabio Estevam [Mon, 6 Jun 2011 05:25:20 +0000 (05:25 +0000)]
imx27lite: Remove local config.mk
Local board config.mk should be avoided.
Place CONFIG_SYS_TEXT_BASE definition into the board config file instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Felix Radensky [Mon, 6 Jun 2011 05:06:07 +0000 (05:06 +0000)]
mx31ads: Fix environment location on flash
At the moment u-boot and u-boot environment on flash
have overlapping addresses, so each u-boot update erases
the environment. Fix this by placing evironment right
after u-boot. Also, remove confusing comment about environment
location.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Fabio Estevam [Mon, 6 Jun 2011 03:13:36 +0000 (03:13 +0000)]
imx31_litekit: Remove local config.mk
Local board config.mk should be avoided.
Place CONFIG_SYS_TEXT_BASE definition into the board config file instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Sun, 5 Jun 2011 14:56:02 +0000 (14:56 +0000)]
mx31litekit: Fix boot with the new relocation scheme.
imx31_litekit has been converted to the new relocation scheme, but it does not boot.
Make the boot functional by using board_early_init_f .
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Fabio Estevam [Sun, 5 Jun 2011 06:26:49 +0000 (06:26 +0000)]
mx31ads: Use the new relocation scheme
This fixes the MX31ADS build by using the new relocation scheme.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Felix Radensky <felix@embedded-sol.com>
Harald Krapfenbauer [Tue, 17 May 2011 19:45:36 +0000 (15:45 -0400)]
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update embedded env settings
The recent commit
ea882baf9c1 broke embedding environments in the middle
of a sector, so relocate it to the start of the 2nd sector.
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 16 May 2011 18:25:42 +0000 (14:25 -0400)]
Blackfin: boards: build zlib dir with -O2
Now that the zlib code has been relocated to a dedicated subdir, make
sure we still build it with -O2 for boards that want speed over size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 9 May 2011 19:43:27 +0000 (15:43 -0400)]
Blackfin: bf548-ezkit/bf561-ezkit: update env location
Relocate the env to one of the small end sectors to avoid issues with
embedding it, such as support being broken (by recent commit
ea882baf9c1),
and for taking a while to save updates.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 30 Apr 2011 08:35:21 +0000 (04:35 -0400)]
Blackfin: use on-chip reset func with newer parts
Turns out the documentation is wrong and doing "RAISE 1" does not result
in a software reset, only a core reset. So when the on-chip rom has a
functioning reset helper, use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 8 Apr 2011 04:52:06 +0000 (00:52 -0400)]
Blackfin: use common LDSCRIPT logic
Now that common code is a bit smarter when it comes to default LDSCRIPT
values, rename the default Blackfin file and drop the Blackfin-specific
config.mk logic.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Thu, 2 Jun 2011 21:19:27 +0000 (23:19 +0200)]
Prepare v2011.06-rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 2 Jun 2011 21:18:32 +0000 (23:18 +0200)]
Minor coding style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
Haojian Zhuang [Sun, 22 May 2011 21:53:30 +0000 (21:53 +0000)]
common/cmd_fdt.c: fix wrong data displayed in fdt print
All data in dtb is big endian. Some ARM devices are little-endian.
In print_data(), it displays data with big-endian format. For ARM device,
data should be converted to little-endian first.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Luuk Paulussen [Mon, 16 May 2011 18:27:11 +0000 (18:27 +0000)]
sntp: avoid use of uninitialized variable
When we use the ntpserverip environment variable argv[1] may not be set.
Printing the error message using the NetNtpServerIP variable ensures the
correct output in both cases.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Patrick Sestier [Fri, 15 Apr 2011 14:25:25 +0000 (14:25 +0000)]
sf: kick watchdog when polling
The status polling can take a while, so make sure we kick the
watchdog after each successful poll.
Signed-off-by: Patrick Sestier <psestier@mircom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Enric Balletbo i Serra [Tue, 31 May 2011 21:01:47 +0000 (21:01 +0000)]
net/net.c: Update ipaddr if the environment has changed
At least on ARM the ipaddr is only set in board_init_r function. The
problem is if ipaddr is not defined in environment importing another
environment defined don't update the ipaddr value.
For example, suppose we've a default environment without net variables
defined and we want to import an uEnv.txt environment from SD-card like
this:
ipaddr=192.168.2.240
netmask=255.255.255.0
gatewayip=192.168.2.1
serverip=192.168.2.114
Then if you try boot from NFS results in:
Importing environment from mmc ...
Running uenvcmd ...
smc911x: detected LAN9221 controller
smc911x: phy initialized
smc911x: MAC ac:de:48:00:00:00
*** ERROR: `ipaddr' not set
The ipaddr at this point is NULL beacause is only set at board_init_r
function. This patch updates the ipaddr value if the environment has
changed.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Wed, 1 Jun 2011 20:16:21 +0000 (22:16 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
sh: sh7785lcr: Update BSC of USB area
Wolfgang Denk [Wed, 1 Jun 2011 20:16:19 +0000 (22:16 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
* 'master' of git://git.denx.de/u-boot-sh:
sh: sh7785lcr: Update BSC of USB area
Wolfgang Denk [Wed, 1 Jun 2011 20:04:29 +0000 (22:04 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
SMDKV310: Fix incorrect conditional compilation for MIU linear mapping
SMDKV310: CPU fequency and mmc_pre_ratio modified
armv7: Add support for ST-Ericsson U8500 href platform
I2C: Add driver for ST-Ericsson U8500 i2c
armv7: Add ST-Ericsson u8500 arch
Kirkwood: boards cleanup for deprecated CONFIG_CMD_AUTOSCRIPT
ARMV7: Vexpress: Add missing MMC header
arm/km: update mgcoge3un board support
mvgbe: enable configurability of PORT_SERIAL_CONTROL_VALUE
arm/km: rename mgcoge2un to mgcoge3un
arm/km: add second serial interface for kirkwood
arm/km: disable ls (through jffs2 support)
arm/km: introduce bootcount env variable and clean km_arm
arm/km: move CONFIG_EXTRA_ENV_SETTINGS from board to km_arm file
arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h
ARMV7: MMC SPL Boot support for SMDKV310 board
ARMV7: Add support for Samsung SMDKV310 Board
S5PC2XX: clock: support pwm clock for evt1 (cpu revision 1)
S5P: add set_mmc_clk for external clock control
S5PC2XX: Support the cpu revision
S5P:SROM config code moved to s5p-common directory
Add _end for the end of u-boot image for SMDK6400
MMC S5P: Fix typo
S5P: GPIO Macro Values Corrected.
SMDK2410: various cleanup/code style fixes
SMDK2410: use the CFI driver (and remove the old one)
SMDK2410: remove unneeded config.mk
SMDK2410: activate ARM relocation feature
BeagleBoard: fixed typo in typecast
mvsata: issue hard reset on initialization
VCMA9: use ARM relocation feature to fix build error
MX31: drop warnings due to missing prototype for mxc_watchdog_reset()
MX5: drop config.mk from efikamx board
MX31: Make get_reset_cause() static and drop unreachable code
MX53: Remove CONFIG_SYS_BOOTMAPSZ from mx53 config files.
MX53: Handle silicon revision 2.1 case
mx5: board: code clean up for checkboard code
MX51: vision2: Fix build for vision2 board.
MX51: vision: Let video mode struct be independant of watchdog.
MX53: Add initial support for MX53SMD board.
MX53: support for freescale MX53LOCO board
mx5: Fix CONFIG_OF_LIBFDT redefined warning
mx5: Remove unnecessary CONFIG_SYS_BOOTMAPSZ definition
mx31pdk: Clean up mx31pdk.h file
Wolfgang Denk [Wed, 1 Jun 2011 20:04:12 +0000 (22:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
SMDKV310: Fix incorrect conditional compilation for MIU linear mapping
SMDKV310: CPU fequency and mmc_pre_ratio modified
armv7: Add support for ST-Ericsson U8500 href platform
I2C: Add driver for ST-Ericsson U8500 i2c
armv7: Add ST-Ericsson u8500 arch
Kirkwood: boards cleanup for deprecated CONFIG_CMD_AUTOSCRIPT
ARMV7: Vexpress: Add missing MMC header
arm/km: update mgcoge3un board support
mvgbe: enable configurability of PORT_SERIAL_CONTROL_VALUE
arm/km: rename mgcoge2un to mgcoge3un
arm/km: add second serial interface for kirkwood
arm/km: disable ls (through jffs2 support)
arm/km: introduce bootcount env variable and clean km_arm
arm/km: move CONFIG_EXTRA_ENV_SETTINGS from board to km_arm file
arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h
ARMV7: MMC SPL Boot support for SMDKV310 board
ARMV7: Add support for Samsung SMDKV310 Board
S5PC2XX: clock: support pwm clock for evt1 (cpu revision 1)
S5P: add set_mmc_clk for external clock control
S5PC2XX: Support the cpu revision
S5P:SROM config code moved to s5p-common directory
Add _end for the end of u-boot image for SMDK6400
MMC S5P: Fix typo
S5P: GPIO Macro Values Corrected.
SMDK2410: various cleanup/code style fixes
SMDK2410: use the CFI driver (and remove the old one)
SMDK2410: remove unneeded config.mk
SMDK2410: activate ARM relocation feature
BeagleBoard: fixed typo in typecast
mvsata: issue hard reset on initialization
VCMA9: use ARM relocation feature to fix build error
MX31: drop warnings due to missing prototype for mxc_watchdog_reset()
MX5: drop config.mk from efikamx board
MX31: Make get_reset_cause() static and drop unreachable code
MX53: Remove CONFIG_SYS_BOOTMAPSZ from mx53 config files.
MX53: Handle silicon revision 2.1 case
mx5: board: code clean up for checkboard code
MX51: vision2: Fix build for vision2 board.
MX51: vision: Let video mode struct be independant of watchdog.
MX53: Add initial support for MX53SMD board.
MX53: support for freescale MX53LOCO board
mx5: Fix CONFIG_OF_LIBFDT redefined warning
mx5: Remove unnecessary CONFIG_SYS_BOOTMAPSZ definition
mx31pdk: Clean up mx31pdk.h file
Wolfgang Denk [Wed, 1 Jun 2011 20:01:10 +0000 (22:01 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/fsl_pci: Fix device tree fixups for newer platforms
Wolfgang Denk [Wed, 1 Jun 2011 20:01:07 +0000 (22:01 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/fsl_pci: Fix device tree fixups for newer platforms
Wolfgang Denk [Wed, 1 Jun 2011 19:59:27 +0000 (21:59 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
cmd_nand: fix help of nand erase subcommand
env_nand: zero-initialize variable nand_erase_options
Marek Vasut [Fri, 20 May 2011 23:48:25 +0000 (01:48 +0200)]
Move wepep250,delta,xsengine to scrapyard
Drop wepep250 board from MAINTAINERS and add all these three boards to
doc/README.scrapyard
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Thomas Abraham [Tue, 31 May 2011 03:52:25 +0000 (03:52 +0000)]
SMDKV310: Fix incorrect conditional compilation for MIU linear mapping
Fix the incorrect macro check for MIU linear mapping conditional compilation.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Thu, 26 May 2011 01:10:34 +0000 (01:10 +0000)]
SMDKV310: CPU fequency and mmc_pre_ratio modified
Modifies CPU Frequency to 1GHz and removes hard coding of mmc_pre_ratio for
MMC Channel2 in FSYS2 register.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
John Rigby [Tue, 19 Apr 2011 10:42:42 +0000 (10:42 +0000)]
armv7: Add support for ST-Ericsson U8500 href platform
Minimal platform support to boot linux from SD.
Supported devices/hw limited to external MMC/SD slot,
GPIO, I2C and minimal PRCMU.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>
Michael Brandt [Tue, 19 Apr 2011 10:42:41 +0000 (10:42 +0000)]
I2C: Add driver for ST-Ericsson U8500 i2c
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Heiko Schocher <hs@denx.de>
John Rigby [Tue, 19 Apr 2011 10:42:40 +0000 (10:42 +0000)]
armv7: Add ST-Ericsson u8500 arch
Based on ST-Ericsson internal git repo.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>
Nobuhiro Iwamatsu [Mon, 4 Apr 2011 06:47:03 +0000 (15:47 +0900)]
sh: sh7785lcr: Update BSC of USB area
A value of BSC of the USB was wrong.
This updates this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Albert ARIBAUD [Tue, 31 May 2011 21:51:55 +0000 (23:51 +0200)]
Kirkwood: boards cleanup for deprecated CONFIG_CMD_AUTOSCRIPT
Dirk Behme [Mon, 23 May 2011 07:40:26 +0000 (07:40 +0000)]
ARMV7: Vexpress: Add missing MMC header
Add a header file with the missing function prototype to fix
ca9x4_ct_vxp.c: In function 'cpu_mmc_init':
ca9x4_ct_vxp.c:93: warning: implicit declaration of function 'arm_pl180_mmci_init'
introduced by commit "ARMV7: Vexpress: Add MMC support"
(
f0c64526b7e51ba997a0f1baf9e74e6d497b957e)
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Matt Waddel <matt.waddel@linaro.org>
Holger Brunck [Tue, 31 May 2011 02:12:52 +0000 (02:12 +0000)]
arm/km: update mgcoge3un board support
We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).
Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Tue, 31 May 2011 02:12:51 +0000 (02:12 +0000)]
mvgbe: enable configurability of PORT_SERIAL_CONTROL_VALUE
This allows this configuration to be defined differently for some
boards that request it.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Tue, 31 May 2011 02:12:50 +0000 (02:12 +0000)]
arm/km: rename mgcoge2un to mgcoge3un
The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.
We add the BootROM init file for the mgcoge3un memphis RAM.
We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Holger Brunck [Tue, 31 May 2011 02:12:49 +0000 (02:12 +0000)]
arm/km: add second serial interface for kirkwood
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Tue, 31 May 2011 02:12:48 +0000 (02:12 +0000)]
arm/km: disable ls (through jffs2 support)
This is not supported on our km-arm boards since we have defined
CONFIG_SYS_NO_FLASH for our NAND Flash chip.
With CONFIG_CMD_JFFS2, the ls command is present and works very badly
on our km-arm boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Valentin Longchamp [Tue, 31 May 2011 02:12:47 +0000 (02:12 +0000)]
arm/km: introduce bootcount env variable and clean km_arm
This environment variable is used to set the bootcount address
for the kernel.
last_stage_init is not available for arm platforms. So the
calls to set_km_var and set_bootcount_addr are done in
misc_init_r.
Additionally some unneeded printouts were removed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Tue, 31 May 2011 02:12:46 +0000 (02:12 +0000)]
arm/km: move CONFIG_EXTRA_ENV_SETTINGS from board to km_arm file
Since all the boards define the same env settings, this simplifies
the board files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Tue, 31 May 2011 02:12:45 +0000 (02:12 +0000)]
arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h
This define is marvell specific, so it should be present in km_arm.
It is however not needed there either, since we set it to the default
value that is already set in include/asm/arch-kirkwood/config.h
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Chander Kashyap [Tue, 24 May 2011 20:02:57 +0000 (20:02 +0000)]
ARMV7: MMC SPL Boot support for SMDKV310 board
Added MMC SPL boot support for SMDKV310. This framework design is
based on nand_spl support.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Tue, 24 May 2011 20:02:56 +0000 (20:02 +0000)]
ARMV7: Add support for Samsung SMDKV310 Board
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Minkyu Kang [Wed, 18 May 2011 07:57:55 +0000 (16:57 +0900)]
S5PC2XX: clock: support pwm clock for evt1 (cpu revision 1)
The source of pwm clock is fixed at evt1.
And some registers for pwm clock are removed.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Jaehoon Chung [Tue, 17 May 2011 21:19:17 +0000 (21:19 +0000)]
S5P: add set_mmc_clk for external clock control
This patch added set_mmc_clk for external clock control.
c210 didn't support host clock control.
So We need external_clock_control function for c210.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Minkyu Kang [Mon, 16 May 2011 10:45:54 +0000 (19:45 +0900)]
S5PC2XX: Support the cpu revision
S5PC210 SoC have two cpu revisions, and have some difference.
So, support the cpu revision for each revision.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Chander Kashyap [Thu, 14 Apr 2011 19:05:18 +0000 (19:05 +0000)]
S5P:SROM config code moved to s5p-common directory
SROM config code is made common for S5P series of boards.
smdkc100.c now refers to s5p-common/sromc.c for SROM related
subroutines.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
seedshope [Sun, 1 May 2011 07:05:37 +0000 (07:05 +0000)]
Add _end for the end of u-boot image for SMDK6400
Since we rename _end to __bss_end__, But we need add _end symbol for
the end of u-boot image.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Dirk Behme [Sun, 15 May 2011 05:39:28 +0000 (05:39 +0000)]
MMC S5P: Fix typo
Fix typo resulting in the compilation error
s5p_mmc.c: In function 's5p_mmc_initialize':
s5p_mmc.c:469: error: 'struct mmc' has no member named 'm_bmax'
introduced by commit "MMC: make b_max unconditional"
(
8feafcc49c0b7a9c541904f95a43dbef2fecc38b)
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: John Rigby <john.rigby@linaro.org>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Mon, 18 Apr 2011 00:08:43 +0000 (00:08 +0000)]
S5P: GPIO Macro Values Corrected.
S5PC2XX: Macro values for Pull Up and Driver Strength were wrong.
S5PC1XX: Macro values for Driver Strength were wrong.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
David Müller (ELSOFT AG) [Thu, 24 Mar 2011 22:28:06 +0000 (22:28 +0000)]
SMDK2410: various cleanup/code style fixes
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
David Müller (ELSOFT AG) [Thu, 24 Mar 2011 22:28:05 +0000 (22:28 +0000)]
SMDK2410: use the CFI driver (and remove the old one)
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
David Müller (ELSOFT AG) [Thu, 24 Mar 2011 22:28:04 +0000 (22:28 +0000)]
SMDK2410: remove unneeded config.mk
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
David Müller (ELSOFT AG) [Thu, 24 Mar 2011 22:28:03 +0000 (22:28 +0000)]
SMDK2410: activate ARM relocation feature
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Daniel Hobi [Thu, 19 May 2011 17:28:54 +0000 (19:28 +0200)]
cmd_nand: fix help of nand erase subcommand
Since commit
30486322 (nand erase: .spread, .part, .chip subcommands)
the arguments off and size are no longer optional.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Daniel Hobi [Wed, 18 May 2011 13:21:08 +0000 (15:21 +0200)]
env_nand: zero-initialize variable nand_erase_options
Commit
30486322 (nand erase: .spread, .part, .chip subcommands)
added a new field to struct nand_erase_options, but forgot to
update common/env_nand.c.
Depending on the stack state and bad block distribution, saveenv()
can thus erase more than CONFIG_ENV_RANGE bytes which may corrupt
the following NAND sectors/partitions.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Jason Kridner [Wed, 20 Apr 2011 13:52:26 +0000 (13:52 +0000)]
BeagleBoard: fixed typo in typecast
Without this patch, you should get a warning.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Michael Walle [Wed, 11 May 2011 12:22:46 +0000 (12:22 +0000)]
mvsata: issue hard reset on initialization
Before the actual initialization do a hard reset of the SATA port and the
connected device.
changes v1->v2:
- add comment for udelay
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
David Müller (ELSOFT AG) [Sun, 1 May 2011 21:52:48 +0000 (21:52 +0000)]
VCMA9: use ARM relocation feature to fix build error
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Stefano Babic [Fri, 20 May 2011 09:01:40 +0000 (11:01 +0200)]
MX31: drop warnings due to missing prototype for mxc_watchdog_reset()
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Thu, 19 May 2011 15:40:01 +0000 (17:40 +0200)]
MX5: drop config.mk from efikamx board
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Stefano Babic [Tue, 17 May 2011 11:45:41 +0000 (13:45 +0200)]
MX31: Make get_reset_cause() static and drop unreachable code
get_reset_cause() should not be exported. Drop code in the function
after return statement that can generate warnings due to unreachable code.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Sun, 15 May 2011 12:58:55 +0000 (12:58 +0000)]
MX53: Remove CONFIG_SYS_BOOTMAPSZ from mx53 config files.
commit
ed59e58 (Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ) made the
definition of CONFIG_SYS_BOOTMAPSZ unnecessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
Fabio Estevam [Tue, 26 Apr 2011 10:50:15 +0000 (10:50 +0000)]
MX53: Handle silicon revision 2.1 case
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Jason Liu [Fri, 22 Apr 2011 02:55:42 +0000 (02:55 +0000)]
mx5: board: code clean up for checkboard code
The boot cause code has been factor out to soc common
code,we need drop the part from the board support code
This patch also remove the redundant cpu version print
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Fabio Estevam [Tue, 10 May 2011 08:13:56 +0000 (08:13 +0000)]
MX51: vision2: Fix build for vision2 board.
config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.
After this change vision2 board can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Tue, 10 May 2011 07:50:46 +0000 (07:50 +0000)]
MX51: vision: Let video mode struct be independant of watchdog.
Currently the fb_videomode struct is only declared if CONFIG_HW_WATCHDOG is defined.
Remove this dependancy and let the video struct always be declared.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 13 May 2011 03:15:11 +0000 (03:15 +0000)]
MX53: Add initial support for MX53SMD board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Jason Liu [Fri, 13 May 2011 01:58:55 +0000 (01:58 +0000)]
MX53: support for freescale MX53LOCO board
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Shawn Guo [Tue, 3 May 2011 20:13:17 +0000 (20:13 +0000)]
mx5: Fix CONFIG_OF_LIBFDT redefined warning
With the following commit, CONFIG_OF_LIBFDT is redefined.
2fa8ca98c37d5b1bb0328b19ddb7e9d162cd9683
Add CONFIG_OF_LIBFDT to more boards.
Remove the duplicated definition to fix CONFIG_OF_LIBFDT redefined
warning.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Tue, 3 May 2011 20:13:16 +0000 (20:13 +0000)]
mx5: Remove unnecessary CONFIG_SYS_BOOTMAPSZ definition
Since the following commit, definition CONFIG_SYS_BOOTMAPSZ is not
needed any more.
ed59e58786cae9f8afcb575649afc65985beed4d
Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fabio Estevam [Tue, 26 Apr 2011 11:04:37 +0000 (11:04 +0000)]
mx31pdk: Clean up mx31pdk.h file
No need to use '#define SYMBOL 1' to make it active.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
ecc [Fri, 20 May 2011 15:33:47 +0000 (15:33 +0000)]
.gitignore: update list of u-boot.* files and add *.bin
This patch adds additional u-boot.* files mentioned in Makefile,
and adds *.bin since these are deleted as part of "make clean".
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Wolfgang Denk [Fri, 20 May 2011 23:13:14 +0000 (23:13 +0000)]
MPC8xx: Make SPD823TS board build again
Commit
e59e356 "TFTP: net/tftp.c: add server mode receive" caused the
size of some object files to grow which breaks the manually optimized
linking for the SPD823TS board. Adjust linker script as needed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Kumar Gala [Fri, 20 May 2011 05:39:21 +0000 (00:39 -0500)]
powerpc/fsl_pci: Fix device tree fixups for newer platforms
We assumed that only a small set of compatiable strings would be needed
to find the PCIe device tree nodes to be fixed up. However on newer
platforms the simple rules no longer work. We need to allow specifying
the PCIe compatiable string for each individual SoC.
We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if
the default isn't sufficient.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Thu, 19 May 2011 20:23:50 +0000 (22:23 +0200)]
Prepare v2011.06-rc1
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 19 May 2011 20:21:41 +0000 (22:21 +0200)]
Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Luca Ceresoli [Tue, 17 May 2011 00:03:41 +0000 (00:03 +0000)]
net/tftp.c: fix typo
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Luca Ceresoli [Tue, 17 May 2011 00:03:40 +0000 (00:03 +0000)]
TFTP: add tftpsrv command
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Luca Ceresoli [Tue, 17 May 2011 00:03:39 +0000 (00:03 +0000)]
TFTP: net/tftp.c: add server mode receive
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Luca Ceresoli [Tue, 17 May 2011 00:03:38 +0000 (00:03 +0000)]
TFTP: rename STATE_RRQ to STATE_SEND_RRQ
With the upcoming TFTP server implementation, requests can be either
outgoing or incoming, so avoid ambiguities.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Luca Ceresoli [Tue, 17 May 2011 00:03:37 +0000 (00:03 +0000)]
TFTP: replace "server" with "remote" in local variable names
With the upcoming TFTP server implementation, the remote node can be
either a client or a server, so avoid ambiguities.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Luca Ceresoli [Sat, 14 May 2011 05:50:03 +0000 (05:50 +0000)]
net/tftp.c: cosmetic: do not initialise statics to 0 or NULL
This removes the following checkpatch issue:
- ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Luca Ceresoli [Sat, 14 May 2011 05:50:02 +0000 (05:50 +0000)]
net/tftp.c: cosmetic: fix indentation
This removes the following checkpatch issue:
- WARNING: suspect code indent for conditional statements
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Luca Ceresoli [Sat, 14 May 2011 05:50:01 +0000 (05:50 +0000)]
net/tftp.c: cosmetic: trailing statements should be on next line
This removes the following checkpatch issue:
- ERROR: trailing statements should be on next line
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
projects / oweals / u-boot.git / log