ARM: UniPhier: add UART initialization routine for low-level debug

The low-level debugging functions are useful to debug the early boot
stage where the full UART driver is not available.

UniPhier SoCs need to initialize the UART port 0 to use this feature.
The initialization routine is called at the very entry of the
lowlevel_init().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: UniPhier: enable output of system bus

For NAND boot on PH1-LD4, PH1-sLD8, and some other SoCs,
the output of the system bus is disabled by default.
It must be enabled by software to have access to the system bus.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: UniPhier: fix SRAM size on support card

The max size of available memories on slot0 and slot1 is 32MB because
 - EA[25] signal is not output on the save-pin mode which is
   used PH1-LD4 or later SoCs.
 - EA[25] signal is not connected by the limitation (or bug?) of
   the PLD logic of DCC support card.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Kconfig: move EXPERT option under "General setup" menu

Make it a sub-menu of "General setup" like Linux Kernel.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

Merge branch 'master' of git://git.denx.de/u-boot-mmc

sunxi: axp221: Fix using the wrong register address for ALDO2

This fixes us never programming ALDO2, and programming the ALDO2 voltage
into ALDo1.

Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

spl: mmc: Fix raw boot mode (related to commit 4c5bbc2328a24f5e1ee990c9a9527e48e5fb3b5f)

As reported by Robert Nelson, commit 4c5bbc2328a24f5e1ee990c9a9527e48e5fb3b5f
may break MMC RAW boot mode.
This patch fixes the check path to fix MMC Raw boot mode.

Tested raw boot mode and FS boot mode on a pandaboard (rev. A3).

Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>

MVEBUMMC : REMOVE unnecessary delay from init

Remove unnessecary delay from mvebu_mmc_initialize

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

MVEBUMMC : CLEAN code

Clean mvebu_mmc_send_cmd

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

MVEBUMMC : REMOVE unnecessary delays

Remove delays in mvebu_mmc_set_bus and mvebu_mmc_set_clk

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

MVEBUMMC : FIX debug strings

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

MVEBUMMC : Speed up access time

Get about 40x faster access on SHEEVAPLUG MMC
 Fix some SD type compatibility

 Changes in v3:
 - fix the HW_STATE (from linux mvsdio)
 - review delays and timeouts

 Changes in v2:
 - increase number of loops
 - remove initial delay

 Changes in v1:
 - review all loops, delays and timeouts

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

MVEBUMMC : Change copyright date

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

spl_sata.c: Add <scsi.h>

We need <scsi.h> for scsi_scan().

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'misc' of git://git.denx.de/u-boot-x86

cros-ec-keyboard: Synchronize DT binding from linux

The ChromeOS EC keyboard is used by various different chromebooks. Peach
pi being the third board in the u-boot tree to use it (snow and peach
pit the other two). Rather then embedding the same big DT node in the
peach-pi DT again, copy the dtsi snippit & bindings documentation from
linux and include it in all 3 boards.

This slightly changes the dt bindings in u-boot:
  * google,key-rows becomes keypad,num-rows
  * google,key-colums becomes keypad,num-colums
  * google,repeat-delay-ms and google,repeat-rate-ms are no longer used
    and replaced by hardcoded values (similar to tegra kbc)

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

i2c_eeprom: include <linux/err.h> to fix build error

drivers/misc/i2c_eeprom.c fails to build unless CONFIG_FIT_SIGNATURE
is defined.

  CC      drivers/misc/i2c_eeprom.o
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:15:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:15:10: note: each undeclared identifier
is reported only once for each function it appears in
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_write':
drivers/misc/i2c_eeprom.c:21:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:22:1: warning: control reaches end of
non-void function [-Wreturn-type]
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:16:1: warning: control reaches end of
non-void function [-Wreturn-type]
make[2]: *** [drivers/misc/i2c_eeprom.o] Error 1
make[1]: *** [drivers/misc] Error 2
make: *** [drivers] Error 2

By the way, Sandbox (enabling CONFIG_FIT_SIGNATURE) is luckily
working depending on it.
Sandbox includes include/asm-generic/errno.h
            from include/errno.h
            from include/u-boot/rsa-checksum.h
            from include/image.h
            from include/common.h
            from drivers/misc/i2c_eeprom.c

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

dm: README: recommend u-boot.dtb to try driver-model on sandbox

To enjoy driver-model on sandbox, using device tree is recommended.
While we are here, change sandbox_config to sandbox_defconfig too.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

memmove_wd: copy chunk down from big address if parameter to is larger than from

When watchdog is enabled, memmove_wd() always copy chunk up from small address.
This damanges overlapped memory data if destination address is smaller than
source address.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Simon Glass <sjg@chromium.org>

mtd: nand: omap_gpmc: fix error handling

"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).

In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.

Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>

powerpc/cm5200: migrate to generic board

Signed-off-by: David Buechi <david.buechi@bbv.ch>

doc: fix grammatical errors in README

Fix various spelling and grammatical errors in the README.

Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>

keystone: set default pci mode to root complex

pci ports are used as root complex in Linux. So set this as default
in u-boot for keystone devices

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>

beagle_x15: enable NFS command

NFS is useful for loading zImage and dts through
NFS export. It saves us from running two services
for loading files over the network (tftp and nfs).

Signed-off-by: Felipe Balbi <balbi@ti.com>

omap5: cm-t54: add sata support

Add configs required for SATA support on CM-T54 board.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>

arm: omap: reset sata on boot

On OMAP platforms (like OMAP5) Linux kernel fails to detect a SATA
device if it is used by U-Boot.

It happens because U-Boot does not reset SATA controller before boot.

Reset the controller on OS boot so that Linux will have a clean state
to work with.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>

OMAP5+: sata/scsi: implement scsi_bus_reset()

Implement missing scsi_bus_reset() for SCSI subsystem commands
on OMAP platforms.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>

ahci-plat: provide a weak scsi_bus_reset() hook

This allow the platform to handle a custom reset sequence.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>

ahci: introduce ahci_reset()

Extract controller reset code from ahci_host_init() into separate
ahci_reset().

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>

da850evm: Use generic board and libfdt, fix size for SPI flash

Add defines to use CONFIG_SYS_GENERIC_BOARD and CONFIG_OF_LIBFDT.
Semi-separate to this: the size of the image for the da850evm has
increased to the point that the size in da850evm.h and the offset for
the environment in SPI flash no longer work.  They are modified to
account for the larger image size.

Signed-off-by: Peter Howard <phoward@gme.net.au>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

fs: fat: read: fix fat16 ls/read issue

The present fat implementation ignores FAT16 long name
directory entries which aren't placed in a single sector.

This was becouse of the buffer was always filled by the
two sectors, and the loop was made also for two sectors.

If some file long name entries are stored in two sectors,
the we have two cases:

Case 1:
Both of sectors are in the buffer - all required data
for long file name is in the buffer.
- Read OK!

Case 2:
The current directory entry is placed at the end of the
second buffered sector. And the next entries are placed
in a sector which is not buffered yet. Then two next
sectors are buffered and the mentioned entry is ignored.
- Read fail!

This commit fixes this issue by:
- read two sectors after loop on each single is done
- keep the last used sector as a first in the buffer
  before the read of two next

The commit doesn't affects the fat32 imlementation,
which works good as previous.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Mikhail Zolotaryov <lebon@lebon.org.ua>
Cc: Tom Rini <trini@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Tested-by: Simon Glass <sjg@chomium.org>

TI: armv7: enable UUID and PART

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining it.

Signed-off-by: Nishanth Menon <nm@ti.com>

Revert "ARM: omap4: Update sdram setting for panda rev A6"

This reverts commit 47a4bea6af77b01d59a410d09a4c34b2dd14cf50.

Signed-off-by: Nishanth Menon <nm@ti.com>

ARM: OMAP4: Panda: rework DMM logic

Part of DMM logic is reuse from commit
47a4bea6af77b01d59a410d09a4c34b2dd14cf50 ("ARM: omap4: Update sdram
setting for panda rev A6") Which broke SDP4430 with ES2.3 (uses old
DDR).

So, to maintain support for newer DDR used in Panda ES rev B3, we
should, in addition to the commit
675cc77a3ae45e8b0ec17128563264d4a509f628 ("ARM:OMAP4+: panda-es: Support
Rev B3 Elpida DDR2 RAM"), DDR timings, also do DMM configuration
specific to Panda.

Signed-off-by: Nishanth Menon <nm@ti.com>

omap-common/hwinit-common.c: timer_init() doesn't need to touch gd

The gd will be cleared at first so we don't need to set arch.tbl to 0.
In addition, the checks later against lastinc also work fine with an
initial value of 0 here.  This also brings us in line with sunxi code
for example.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

am33xx: Drop timer_init call from s_init

In both SPL and non-SPL cases we will make a call to timer_init() early
on and do not need to call it again within s_init().

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

socfpga: Drop redundant save_boot_params

The save_boot_params function here is the same as the default weak one
from arch/arm/cpu/armv7/start.S, drop.

Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>

cmd_fdt: fix working_fdt is set to wrong value

Instead of setting working_fdt to map_sysmem(addr) (e.g. blob), it should be set
to addr directly as inside set_working_fdt_addr it uses map_sysmem(addr) again.
To test: ./u-boot -d dts/dt.bin , then issue: fdt addr 0x100, fdt print will
then cause an segmentation fault. After this fix fdt print is functional.

ARM: bootm: do not add PSCI to fdt when booting in secure mode.

Commit 8bc347e2ec17 "ARM: bootm: Allow booting in secure mode on hyp capable
systems" added the capability to select nonsec vs sec mode boot via an
environment var.

There is a subtle gotcha with this functionality, which is that the PSCI nodes
are still created in the fdt (via armv7_update_dt->fdt_psci) even when booting
in secure mode. Which means that if the kernel is PSCI aware then it will fail
to boot because it will try and do PSCI from secure world, which won't work.

This likely didn't get noticed before because the original purpose was to
support booting the legacy linux-sunxi kernels which don't understand PSCI.

To fix expose boot_nonsec (renaming with armv7_ prefix) outside of bootm.c and
use from the virt-dt code.

As well as avoiding the creation of the PSCI nodes we should also avoid
reserving the secure RAM, so do so.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

devkit8000: convert to use generic board code

Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>

cmd_bdinfo: check for CONFIG_ARC instead of CONFIG_ARC700

For all flavours of ARC we execute the same code in "bdinfo" so we may
safely check for CONFIG_ARC. This is especially important since we're
about to add more types of ARC so existing check won't work in all
cases.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>

arm: omap3: cm-t35: convert to generic board

Convert cm-t35 to generic board.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

powerpc: mpc824x: remove MPC824X cpu support

All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>

mpc8260: remove atc board support

These boards are still non-generic boards.

drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8260: remove CPU86, CPU87 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8260: remove ep82xxm board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

mpc8260: remove gw8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Oliver Brown <obrown@adventnetworks.com>

mpc8260: remove IPHASE4539 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Grandegger <wg@denx.de>

mpc8260: remove muas3001 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>

mpc8260: remove PM825, PM826, PM828 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8260: remove MPC8266ADS board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rune Torgersen <runet@innovsys.com>

mpc8260: remove VoVPN-GW board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

mpc8260: remove ep8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Frank Panno <fpanno@delphintech.com>

mpc8260: remove ppmc8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Brad Kemp <Brad.Kemp@seranoa.com>

mpc8260: remove sacsng board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>

powerpc: remove cogent_8xx, cogent_mpc8260 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Murray Jensen <Murray.Jensen@csiro.au>

mpc8xx: remove ESTEEM192E board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Conn Clark <clark@esteem.com>

mpc8xx: remove IP860 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove IVMS8, IVML24 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove lwmon board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove NETVIA board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Pantelis Antoniou <panto@intracom.gr>

mpc8xx: remove R360MPI board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove RRvision board support

This board is still a non-generic board.

Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove SPD823TS board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove KUP4X, KUP4K board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Klaus Heydeck <heydeck@kieback-peter.de>

mpc8xx: remove ELPT860 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: The LEOX team <team@leox.org>

powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>

mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-spi

Merge branch 'master' of git://git.denx.de/u-boot-tegra

Merge branch 'master' of git://git.denx.de/u-boot-usb

Conflicts:
include/configs/arndale.h

Signed-off-by: Tom Rini <trini@ti.com>

usb: eth: enable AX88179 DRIVER for ARNDALE 5250

Patch enables AX88179 driver for ARNDALE 5250

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>

usb: eth: add ASIX AX88179 DRIVER

This patch adds driver support for the ASIX AX88179 USB3.0 to GbE network
adapter.

Driver has been tested on the RECS5250 COM module (similar to ARDALE5250).
Testcase was DHCP and PXE boot.

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>

imx:mx6slevk add spi nor boot support

Add spi nor boot support for mx6slevk board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

imx:mx6sxsabresd add qspi support

Configure the pad setting and enable qspi clock to support qspi
flashes access.

Add QSPI related macro in configuration header file.

Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR  and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

imx:qspi add 4K erase support

Add 4k erase command support for qspi driver. reuse the 64k erase function,
but change the function name from qspi_op_se to qspi_op_erase, since it
supports 64k and 4k erase.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

arm:mx6sx add QSPI support

Add QSPI support for mx6solox.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

QuadSPI: use correct amba_base

According cs, use different amba_base to choose the corresponding
flash devices.  If not, `sf probe 1:0` and `sf probe 1:1` will
choose the same flash device, but not different flash devices.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

QuadSPI: use QSPI_CMD_xx instead of flash opcodes

Use QSPI_CMD_xx instead of flash opcodes

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

Merge branch 'master' of git://denx.de/git/u-boot-imx

Merge branch 'master' of git://git.denx.de/u-boot-uniphier

Merge branch 'master' of git://git.denx.de/u-boot-samsung

mx6slevk: Remove get_board_rev()

get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.

Let's get rid of get_board_rev() as it is not being used with its correct
meaning.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

arm: mx6: novena: Add proper LVDS display support

Repair the register configuration and add proper support for the
display attached to both LVDS channels.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Pull video handling into separate file

Pull all of the video handling into a separate file, since a lot
more code will be added and such code would polute the board file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Pull GPIO definitions into header

Pull the definitions of GPIOs into a separate header file, so that
they can be used across all source files.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Minor config file fix

Sequence like the following is completely useless and results from
an errorneous ordering of the statements during development. Zap it.
 #ifdef FOO
 #define FOO

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Minor coding style fix

Just zap multiple spaces and replace them with tabs properly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Define CONFIG_SYS_MALLOC_F_LEN

This board uses setup_i2c() in SPL. The setup_i2c() function internally
calls gpio_request(), which in turn internally calls strdup(). The strdup()
requires a running mallocator, so this patch makes the mallocator available.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: gw_ventana: Define CONFIG_SYS_MALLOC_F_LEN

This board uses setup_i2c() in SPL. The setup_i2c() function internally
calls gpio_request(), which in turn internally calls strdup(). The strdup()
requires a running mallocator, so this patch makes the mallocator available.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

imx: i2c: Zap unnecessary malloc() calls

The malloc() calls are unnecessary, just allocate the stuff on stack.
While at it, reorder the code a little, so that only one variable is
used for the text, use snprintf() instead of sprintf() and use %01d
as a formatting string to avoid any possible overflows.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

embestmx6boards: convert to use config_distro_bootcmd.h

Since the Riot & Mars boards are dev boards it's likely people will want to
run standard distros on them. So replace the current boot scripts with the
standard one from config_distro_bootcmd.h

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Tested-by: Nikolay Dimitrov <picmaster@mail.bg>

embestmx6boards: convert to use config_distro_defaults.h

Update to use config_distro_defaults.h and remove explicit settings

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Tested-by: Nikolay Dimitrov <picmaster@mail.bg>

imx SPL: enable boot from eMMC boot partitions.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

ARM: UniPhier: display boot swap pin status by pinmon command

This information would be useful enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: UniPhier: add dump command of DDR PHY parameters

This commit adds a dump command of DDR PHY parameters of UniPhier
SoC family.  It might not be used very often for the regular operation
but it would be useful when something goes wrong with DDR memories.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>