Nick Spence [Thu, 28 Aug 2008 21:09:11 +0000 (14:09 -0700)]
mpc83xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Nick Spence [Sat, 23 Aug 2008 06:52:50 +0000 (23:52 -0700)]
MPC83XX: Fix GPIO configuration - set gpio level before direction
Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.
Set gpio level register before direction register to inhibit
glitches on high level output pins.
Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.
Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 1 Sep 2008 15:11:26 +0000 (17:11 +0200)]
device: make device_register() clone the device
This is expected by the callers, but this fact was hidden well within
the old list implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sun, 31 Aug 2008 22:16:29 +0000 (00:16 +0200)]
Merge branch 'Makefile' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Sun, 31 Aug 2008 22:06:05 +0000 (00:06 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Sun, 31 Aug 2008 22:04:26 +0000 (00:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Sun, 31 Aug 2008 22:03:40 +0000 (00:03 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Wolfgang Denk [Sun, 31 Aug 2008 21:53:22 +0000 (23:53 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 14:28:15 +0000 (23:28 +0900)]
sh: Remove CC line from board's Makefile
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 14:25:57 +0000 (23:25 +0900)]
sh: Replaced "@./mkconfig" for @$(MKCONFIG)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 05:50:52 +0000 (14:50 +0900)]
sh: Add support sh2 to MAKEALL
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 05:52:23 +0000 (14:52 +0900)]
sh: Fix compile error rsk7203 board
This boards used old type preprocessor.
This patch fix compile error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 05:53:31 +0000 (14:53 +0900)]
sh: Fix compile error sh7785lcr board
This boards used old type preprocessor.
This patch fix compile error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 22 Aug 2008 08:39:09 +0000 (17:39 +0900)]
sh: Renesas Solutions AP325RXA board support
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 22 Aug 2008 08:48:51 +0000 (17:48 +0900)]
sh: add support Renesas SH7723
Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other.
This patch supports CPU register's header file and SCIF serial driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 14:02:04 +0000 (23:02 +0900)]
sh: Renesas RSK+ 7203 board support
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 3 Jul 2008 14:11:02 +0000 (23:11 +0900)]
sh: Add support Renesas SH7203 processor
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 13:48:33 +0000 (22:48 +0900)]
sh: Add support SH2/SH2A which is CPU of Renesas Technology
Add support SH2/SH2A basic function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 13:45:08 +0000 (22:45 +0900)]
sh: Renesas R0P7785LC0011RL board support
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Yoshihiro Shimoda [Thu, 10 Jul 2008 10:32:53 +0000 (19:32 +0900)]
sh: add support for SH7785
Renesas SH7785 has DDR2-SDRAM controller, PCI, and other.
This patch supports CPU register's header file.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:45:42 +0000 (04:45 +0200)]
davinci: fix remaining dm644x_eth
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:24:56 +0000 (04:24 +0200)]
fs: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:24:55 +0000 (04:24 +0200)]
devices: merge to list_head
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:24:51 +0000 (04:24 +0200)]
update linux/list
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 22:39:48 +0000 (00:39 +0200)]
smdk6400: add gitignore
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 22:39:48 +0000 (00:39 +0200)]
smdk6400: Use CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
smdk6400: remove redundant bootargs definition
Double bootargs setting leads to a duplicated environmant entry.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
ARM: Add support for S3C6400 based SMDK6400 board
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
NAND: add NAND driver for S3C64XX
Based on the original S3C64XX NAND driver by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
S3C64XX: remove broken HWFLOW support from the serial driver
As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is
broken and currently unused. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
serial: add S3C64XX serial driver
Based on the original S3C64XX UART driver by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
USB: Add support for OHCI controller on S3C6400
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
ARM: Add arm1176 core with S3C6400 SoC
Based on the original S3C64XX port by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Sandeep Paulraj [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
ARM DaVinci: Changing function names for EMAC driver
DM644x is just one of a series of DaVinci chips that use the EMAC driver.
By replacing all the function names that start with dm644x_* to davinci_*
we make these function more portable. I have tested this change on my EVM.
DM6467 is another DaVinci SOC which uses the EMAC driver and i will
be sending patches that add DaVinci DM6467 support to the list soon.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Gururaja Hebbar K R [Sat, 30 Aug 2008 21:21:30 +0000 (23:21 +0200)]
Integrator[AP/CP] - Remove unused file memsetup.S
- memsetup.s is changed/merged to lowlevel_init.S
memsetup.S has a global label memsetup that just returns back to caller
- memsetup global label is changed/merged to lowlevel_init
This label is not called from anywhere.
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
Hugo Villeneuve [Wed, 27 Aug 2008 19:35:52 +0000 (21:35 +0200)]
ARM DaVinci: Standardize names of directories/files
ARM DaVinci: Standardize names of directories/files.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Hugo Villeneuve [Fri, 11 Jul 2008 19:10:13 +0000 (15:10 -0400)]
ARM DaVinci: Move common functions to board/davinci/common
ARM DaVinci: Move common functions to board/davinci/common.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Stefan Roese [Fri, 29 Aug 2008 09:56:49 +0000 (11:56 +0200)]
ppc4xx/NAND: Add select_chip function to 4xx NDFC driver
This function is needed for the new NAND infrastructure. We only need
a dummy implementation though for the NDFC.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 29 Aug 2008 10:06:27 +0000 (12:06 +0200)]
ppc4xx: Increase image size for NAND boot target
This is needed since now with HUSH enabled (amcc-common.h) the image
read from NAND exceeds the previous limit.
Signed-off-by: Stefan Roese <sr@denx.de>
Ben Warren [Fri, 29 Aug 2008 06:58:30 +0000 (23:58 -0700)]
Move MPC512x_FEC driver to drivers/net
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Fri, 29 Aug 2008 06:58:29 +0000 (23:58 -0700)]
Move MPC5xxx_FEC driver to drivers/net
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:57 +0000 (21:53 +0200)]
cmd_terminal: remove no need ifdef
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:57 +0000 (21:53 +0200)]
common/Makefile: order by functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:56 +0000 (21:53 +0200)]
miiphyutil: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:37 +0000 (21:53 +0200)]
autoscript: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 23:18:11 +0000 (01:18 +0200)]
crc16: move to lib_generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 23:18:01 +0000 (01:18 +0200)]
miiphybb: move to drivers/net/phy
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 10:31:51 +0000 (12:31 +0200)]
soft_spi: move to drivers/spi
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 10:31:51 +0000 (12:31 +0200)]
soft_i2c: move to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 10:31:48 +0000 (12:31 +0200)]
gunzip: move to lib_generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Ocker [Tue, 26 Aug 2008 17:55:23 +0000 (19:55 +0200)]
ppc4xx: NAND configuration
Made NAND bank configuration setting a config variable.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Victor Gallardo [Thu, 28 Aug 2008 23:03:28 +0000 (16:03 -0700)]
ppc4xx: fix UIC external_interrupt hang on UIC0
This patch fixes a UIC external_interrupt hang if critical or non-critical
interrupt is set at the same time as a normal interrupt is set on UIC0.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Prodyut Hazarika [Wed, 27 Aug 2008 23:39:00 +0000 (16:39 -0700)]
ppc4xx: Optimizations/Cleanups for IBM DDR2 Memory Controller
Removed Magic numbers from Initialization preload registers
Tested with Kilauea, Glacier, Canyonlands and Katmai boards
About 5-7% improvement seen for LMBench memtests
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
John Rigby [Thu, 28 Aug 2008 19:17:07 +0000 (13:17 -0600)]
ADS5121: Fix NOR and CPLD ALE timing for rev 2 silicon
MPC5121 rev 2 silicon has a new register for controlling how long
CS is asserted after deassertion of ALE in multiplexed mode.
The default is to assert CS together with ALE. The alternative
is to assert CS (ALEN+1)*LPC_CLK clocks after deassertion of ALE.
The default is wrong for the NOR flash and CPLD on the ADS5121.
This patch turns on the alternative for CS0 (NOR) and CS2 (CPLD)
it does so conditionally based on silicon rev 2.0 or greater.
Signed-off-by: Martha J Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
TsiChung Liew [Mon, 18 Aug 2008 18:56:46 +0000 (00:56 +0600)]
Add I2C frequency dividers for ColdFire
The existing I2C freqency dividers for FDR does not apply
to ColdFire platforms; thus, a seperate table is added
based on MCF5xxx Reference Manual
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Tabi Timur <timur@freescale.com>
TsiChung Liew [Mon, 18 Aug 2008 21:01:19 +0000 (03:01 +0600)]
ColdFire: I2C fix for multiple platforms
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
TsiChung Liew [Mon, 18 Aug 2008 18:37:13 +0000 (00:37 +0600)]
ColdFire: Add CONFIG_MII_INIT for M5272C3
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
TsiChung Liew [Mon, 18 Aug 2008 18:26:25 +0000 (00:26 +0600)]
ColdFire: Multiple fixes for MCF5445x platforms
Add FEC pin set and mii reset in __mii_init(). Change
legacy flash vendor from 2 to AMD LEGACY (0xFFF0),
change cfi_offset to 0, and change CFG_FLASH_CFI to
CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and
M54455EVB env settings in configuration file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
TsiChung Liew [Fri, 15 Aug 2008 18:24:25 +0000 (18:24 +0000)]
ColdFire: Change the SDRAM BRD2WT timing from 3 to 7
The user manuals recommend 7.
Signed-off-by: Kurt Mahan <kmahan@freescale.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
TsiChung Liew [Fri, 15 Aug 2008 16:50:07 +0000 (16:50 +0000)]
ColdFire: Raise uart baudrate to 115200 bps
M5249EVB, M5271EVB, M5272C3, M5275EVB and M5282EVB platforms
uart baudrate increase from 19200 to 115200 bps
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
TsiChung Liew [Wed, 13 Aug 2008 12:07:03 +0000 (12:07 +0000)]
ColdFire: Fix board.c warning message
Implicit declaration of nand_init() warning message
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Wolfgang Denk [Wed, 27 Aug 2008 22:39:43 +0000 (00:39 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Wed, 27 Aug 2008 22:39:27 +0000 (00:39 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Kumar Gala [Wed, 27 Aug 2008 06:10:34 +0000 (01:10 -0500)]
FSL DDR: Remove duplicate setting of cs0_bnds register on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Wed, 27 Aug 2008 22:26:52 +0000 (00:26 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Heiko Schocher [Thu, 21 Aug 2008 18:44:49 +0000 (20:44 +0200)]
mpc52xx: added support for the MPC5200 based MUC.MC52 board from MAN.
Signed-off-by: Heiko Schocher <hs@denx.de>
Kumar Gala [Tue, 19 Aug 2008 19:46:36 +0000 (14:46 -0500)]
mpc85xx: remove redudant code with lib_ppc/interrupts.c
For some reason we duplicated the majority of code in lib_ppc/interrupts.c
not show how that happened, but there is no good reason for it.
Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why
they exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 25 Jul 2008 18:31:05 +0000 (13:31 -0500)]
mpc85xx: Add support for the MPC8536DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 12 Aug 2008 16:14:19 +0000 (11:14 -0500)]
mpc85xx: Add support for the MPC8536
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Kumar Gala [Tue, 12 Aug 2008 16:13:08 +0000 (11:13 -0500)]
mpc85xx: Add support for the MPC8572DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 06:05:35 +0000 (01:05 -0500)]
FSL DDR: Remove old SPD support from cpu/mpc85xx
All 85xx boards have been converted to the new code so we can
remove the old SPD DDR setup code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 06:04:07 +0000 (01:04 -0500)]
FSL DDR: Convert STXSSA to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 06:03:42 +0000 (01:03 -0500)]
FSL DDR: Convert STXGP3 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 04:52:58 +0000 (23:52 -0500)]
FSL DDR: Convert SBC8560 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 04:52:32 +0000 (23:52 -0500)]
FSL DDR: Convert MPC8540EVAL to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 04:52:07 +0000 (23:52 -0500)]
FSL DDR: Convert PM856 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 04:51:49 +0000 (23:51 -0500)]
FSL DDR: Convert PM854 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 04:15:28 +0000 (23:15 -0500)]
FSL DDR: Convert sbc8548 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 04:14:14 +0000 (23:14 -0500)]
FSL DDR: Convert atum8548 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 03:56:56 +0000 (22:56 -0500)]
FSL DDR: Convert socrates to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 26 Aug 2008 13:02:30 +0000 (08:02 -0500)]
FSL DDR: Convert MPC8544DS to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Tue, 18 Mar 2008 18:51:05 +0000 (13:51 -0500)]
FSL DDR: Convert MPC8568MDS to new DDR code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Tue, 18 Mar 2008 18:51:06 +0000 (13:51 -0500)]
FSL DDR: Convert MPC8548CDS to new DDR code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Mon, 17 Mar 2008 20:48:18 +0000 (15:48 -0500)]
FSL DDR: Convert MPC8541CDS to new DDR code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Tue, 18 Mar 2008 16:12:42 +0000 (11:12 -0500)]
FSL DDR: Convert MPC8555ADS to new DDR code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Tue, 18 Mar 2008 16:12:44 +0000 (11:12 -0500)]
FSL DDR: Convert MPC8560ADS to new DDR code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 6 Jun 2008 18:12:18 +0000 (13:12 -0500)]
FSL DDR: Convert MPC8540ADS to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 27 Aug 2008 02:34:55 +0000 (21:34 -0500)]
FSL DDR: Add 85xx specific register setting
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 9 Jun 2008 16:07:46 +0000 (11:07 -0500)]
FSL DDR: Add e500 TLB helper for DDR code
Provide a helper function that board code can call to map TLBs when
setting up DDR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andrew Dyer [Tue, 26 Aug 2008 22:03:38 +0000 (17:03 -0500)]
dm9000 remove dead external phy support, gpio fix
dm9000 has code to detect and initialize external phy parts, but later
on in the code the part is forced to use the internal phy
unconditionally. Remove the unused/untested code.
change the GPIO initialization so that only the GPIO used as an
internal phy reset (hardwired in the chip) is set as an output. The
remaining GPIO need to be handled by board specific code to prevent
possible drive conflicts. Set as inputs for safety.
replace a few magic numbers with defines
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Peter Tyser [Tue, 26 Aug 2008 16:17:48 +0000 (11:17 -0500)]
Standardize bootp, tftpboot, rarpboot, dhcp, and nfs command descriptions
cmd_net.c command descriptions were updated to describe the optional
hostIPaddr argument. The dhcp command help message was also updated
to more closely reflect the other commands in cmd_net.c
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remy Bohmer [Wed, 20 Aug 2008 09:30:28 +0000 (11:30 +0200)]
Fix bogus error message in the DHCP handler
The DHCP handler has 1 state that is not listed in this case, causing a
failure message when there is actually no failure.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remy Bohmer [Wed, 20 Aug 2008 09:30:27 +0000 (11:30 +0200)]
Fix compile error when CONFIG_BOOTP_RANDOM_DELAY is set.
The option CONFIG_BOOTP_RANDOM_DELAY does not compile, because of a
missing extern inside the net/bootp.h header
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
TsiChung Liew [Tue, 19 Aug 2008 21:26:32 +0000 (21:26 +0000)]
ColdFire: Add FEC Buffer descriptors in SRAM
Add FEC Buffer descriptors and data buffer in SRAM for
faster execution and access.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
TsiChung Liew [Thu, 21 Aug 2008 23:55:11 +0000 (23:55 +0000)]
Fix ColdFire FEC warning messages
Types mismatch and implicit declaration of icache_invalid()
warning messages
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sat, 12 Jul 2008 07:17:50 +0000 (00:17 -0700)]
Moved initialization of SKGE Ethernet driver to board code.
The only board using this driver is the SL8245 board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sat, 12 Jul 2008 07:08:45 +0000 (00:08 -0700)]
Moved conditional compilation to Makefile for SK98 Ethernet driver
Brute-force removal of #ifdefs. Didn't touch the code.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sat, 12 Jul 2008 06:42:19 +0000 (23:42 -0700)]
Moved initialization of ULI526X Ethernet driver to board code.
The only board using this driver is the Freescale MPC8610HPCD board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sat, 12 Jul 2008 06:15:28 +0000 (23:15 -0700)]
Moved initialization of Blackfin EMAC Ethernet controller to board_eth_init()
Added board_eth_init() function to bf537-stamp board.
Removed initialization for the Blackin EMAC driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Wed, 9 Jul 2008 08:04:19 +0000 (01:04 -0700)]
Moved initialization of GRETH Ethernet driver to CPU directory
Added a cpu_eth_init() function to leon2/leon3 CPU directories and
removed code from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
projects / oweals / u-boot.git / log