imx:mx6sxsabresd support qspi AHB read

Add CONFIG_SYS_FSL_QSPI_AHB in header file to enable AHB in driver.
In order to count the time, add CONFIG_CMD_TIME.

Using AHB read can improve the the read speed about 30%.

AHB read:
=> time sf read 0x8f800000 0 100000
SF: 1048576 bytes @ 0x0 Read: OK
time: 0.174 seconds

=> time sf read 0x8f800000 1000000 100000
SF: 1048576 bytes @ 0x1000000 Read: OK
time: 0.174 seconds

IP read:
=> time sf read 0x8f800000 0 100000
SF: 1048576 bytes @ 0x0 Read: OK
time: 0.227 seconds

=> time sf read 0x8f800000 1000000 100000
SF: 1048576 bytes @ 0x1000000 Read: OK
time: 0.227 seconds

Note:
Quad read is not supported in driver, now. In my side, using AHB and Quad read
can achieve about 16MB/s. Anyway, I have plan to reimplement the driver using
DTB and DM, then make the code cleaner and more feature can be added.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

qspi:fsl implement AHB read

The QSPI controller in i.MX 6SoloX and Vybrid supports reading data using
IP register and AHB bus.

The original driver only supports reading data from IP interface. The IC
team suggests to use AHB read which is faster then IP read. Using AHB read,
we can directly memcpy, a "missed" access to the buffer will cause the
controller to clear the buffer and use the SEQID stored in bfgencr register
to initiate a read from flash device.

Since AHB bus is 64 bit width, we can not set MCR register using 32bit. In
order to minimize code change, redefine QSPI_MCR_END_CFD_LE to 64bit Little
endian but not 32bit Little endia.

Introduce a new configuration option CONFIG_SYS_FSL_QSPI_AHB. If want to
use AHB read, just define CONFIG_SYS_FSL_QSPI_AHB. If not, just ignore it.
Actually if Vybrid is migrated to use AHB read, this option can be removed and
IP read function can be discared. The reason to introduce this option
is that only i.MX SOC is tested in my side, no Vybrid platform for me.

In spi_setup_slave, the original piece code to set AHB is deleted, since
Vybrid platform does not use this to intiate AHB read. Instead, add
qspi_init_ahb_read function if defined CONFIG_SYS_FSL_QSPI_AHB.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

spi: ftssp010_spi: Simplify code flow in ftssp010_[wait|wait_tx|wait_rx]

No functional change, just simplify the code a bit.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

spi: cadence_qspi: Fix checking return value of fdt_first_subnode()

fdt_first_subnode() returns -FDT_ERR_NOTFOUND if no subnode found.
0 is supposed to be a valid offset returns from fdt_first_subnode().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

mx6sxsabresd: support qspi flash bigger than 16MB

mx6sxsabresd revb board uses 32MB qspi flash, reva board uses 16MB qspi
flash. Currently, the default supported platform is revb board.

If want to configure for reva board, just define CONFIG_MX6SX_SABRESD_REVA
in mx6sxsabresd.h to support reva qspi flashes whose size is 16MB.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

spi:fsl-quadspi support bank register read write

To support bigger than 16MB size qspi flashes, spi framework uses bank
switch to access higher bank or lower bank.

In this patch, QSPI_CMD_BRRD, QSPI_CMD_BRWR, QSPI_CMD_WREAR, QSPI_CMD_RDEAR
is initialized in LUT register with related pad and length configuration.
qspi_op_pp is originally for page programming, this patch reuses this function
for bank register switch and renamed it with qspi_op_write.

Since bank or EAR register is only 1 byte length, however original qspi_op_pp
or now renamed qspi_op_write only support 4 bytes lenght as the access unit,
this will trigger data abort exception when access EAR or bank register.
This is because upper framework passes a 1 bytes pointer to qspi_op_write,
however qspi_op_write treat it as an int pointer. This patch fixes this for
accessing EAR or bank register.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

dt: socfpga: Replace num-chipselect with num-cs

This optional DT property is called 'num-cs', so repair the misnomers.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

dt: socfpga: Rename snps, dw-spi-mmio to snps, dw-apb-ssi

Linux now also contains SPI driver, yet the name is 'snps,dw-apb-ssi'.
Fix the naming before we have to support both names.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

spi: designware_spi: Fix detecting FIFO depth

Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
   register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
   to test fifo == 257. In the case fifo is 257, it means the latest valid
   setting is fifo = 256. So after the for loop iteration, we should check
   fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

powerpc: mpc824x: remove MPC824X cpu support

All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>

mpc8260: remove atc board support

These boards are still non-generic boards.

drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8260: remove CPU86, CPU87 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8260: remove ep82xxm board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

mpc8260: remove gw8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Oliver Brown <obrown@adventnetworks.com>

mpc8260: remove IPHASE4539 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Grandegger <wg@denx.de>

mpc8260: remove muas3001 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>

mpc8260: remove PM825, PM826, PM828 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8260: remove MPC8266ADS board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rune Torgersen <runet@innovsys.com>

mpc8260: remove VoVPN-GW board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

mpc8260: remove ep8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Frank Panno <fpanno@delphintech.com>

mpc8260: remove ppmc8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Brad Kemp <Brad.Kemp@seranoa.com>

mpc8260: remove sacsng board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>

powerpc: remove cogent_8xx, cogent_mpc8260 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Murray Jensen <Murray.Jensen@csiro.au>

mpc8xx: remove ESTEEM192E board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Conn Clark <clark@esteem.com>

mpc8xx: remove IP860 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove IVMS8, IVML24 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove lwmon board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove NETVIA board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Pantelis Antoniou <panto@intracom.gr>

mpc8xx: remove R360MPI board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove RRvision board support

This board is still a non-generic board.

Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove SPD823TS board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

mpc8xx: remove KUP4X, KUP4K board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Klaus Heydeck <heydeck@kieback-peter.de>

mpc8xx: remove ELPT860 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: The LEOX team <team@leox.org>

powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>

mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-spi

Merge branch 'master' of git://git.denx.de/u-boot-tegra

Merge branch 'master' of git://git.denx.de/u-boot-usb

Conflicts:
include/configs/arndale.h

Signed-off-by: Tom Rini <trini@ti.com>

usb: eth: enable AX88179 DRIVER for ARNDALE 5250

Patch enables AX88179 driver for ARNDALE 5250

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>

usb: eth: add ASIX AX88179 DRIVER

This patch adds driver support for the ASIX AX88179 USB3.0 to GbE network
adapter.

Driver has been tested on the RECS5250 COM module (similar to ARDALE5250).
Testcase was DHCP and PXE boot.

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>

imx:mx6slevk add spi nor boot support

Add spi nor boot support for mx6slevk board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

imx:mx6sxsabresd add qspi support

Configure the pad setting and enable qspi clock to support qspi
flashes access.

Add QSPI related macro in configuration header file.

Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR  and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

imx:qspi add 4K erase support

Add 4k erase command support for qspi driver. reuse the 64k erase function,
but change the function name from qspi_op_se to qspi_op_erase, since it
supports 64k and 4k erase.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

arm:mx6sx add QSPI support

Add QSPI support for mx6solox.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

QuadSPI: use correct amba_base

According cs, use different amba_base to choose the corresponding
flash devices.  If not, `sf probe 1:0` and `sf probe 1:1` will
choose the same flash device, but not different flash devices.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

QuadSPI: use QSPI_CMD_xx instead of flash opcodes

Use QSPI_CMD_xx instead of flash opcodes

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

Merge branch 'master' of git://denx.de/git/u-boot-imx

Merge branch 'master' of git://git.denx.de/u-boot-uniphier

Merge branch 'master' of git://git.denx.de/u-boot-samsung

mx6slevk: Remove get_board_rev()

get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.

Let's get rid of get_board_rev() as it is not being used with its correct
meaning.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

arm: mx6: novena: Add proper LVDS display support

Repair the register configuration and add proper support for the
display attached to both LVDS channels.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Pull video handling into separate file

Pull all of the video handling into a separate file, since a lot
more code will be added and such code would polute the board file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Pull GPIO definitions into header

Pull the definitions of GPIOs into a separate header file, so that
they can be used across all source files.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Minor config file fix

Sequence like the following is completely useless and results from
an errorneous ordering of the statements during development. Zap it.
 #ifdef FOO
 #define FOO

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Minor coding style fix

Just zap multiple spaces and replace them with tabs properly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: novena: Define CONFIG_SYS_MALLOC_F_LEN

This board uses setup_i2c() in SPL. The setup_i2c() function internally
calls gpio_request(), which in turn internally calls strdup(). The strdup()
requires a running mallocator, so this patch makes the mallocator available.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

arm: mx6: gw_ventana: Define CONFIG_SYS_MALLOC_F_LEN

This board uses setup_i2c() in SPL. The setup_i2c() function internally
calls gpio_request(), which in turn internally calls strdup(). The strdup()
requires a running mallocator, so this patch makes the mallocator available.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>

imx: i2c: Zap unnecessary malloc() calls

The malloc() calls are unnecessary, just allocate the stuff on stack.
While at it, reorder the code a little, so that only one variable is
used for the text, use snprintf() instead of sprintf() and use %01d
as a formatting string to avoid any possible overflows.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

embestmx6boards: convert to use config_distro_bootcmd.h

Since the Riot & Mars boards are dev boards it's likely people will want to
run standard distros on them. So replace the current boot scripts with the
standard one from config_distro_bootcmd.h

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Tested-by: Nikolay Dimitrov <picmaster@mail.bg>

embestmx6boards: convert to use config_distro_defaults.h

Update to use config_distro_defaults.h and remove explicit settings

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Tested-by: Nikolay Dimitrov <picmaster@mail.bg>

imx SPL: enable boot from eMMC boot partitions.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

ARM: UniPhier: display boot swap pin status by pinmon command

This information would be useful enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: UniPhier: add dump command of DDR PHY parameters

This commit adds a dump command of DDR PHY parameters of UniPhier
SoC family.  It might not be used very often for the regular operation
but it would be useful when something goes wrong with DDR memories.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: UniPhier: add DDR PHY training code

This training code provides run-time adjustment of DDR PHY parameters
for stable DDR operation.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Exynos: Move down common USB configuration

USB is a pretty common feature on exynos 5 board, so it seems sensible
to configure it directly from exynos5-common. As a side-effect this
makes USB available from u-boot on exynos 5420 based boards.

While there enable support for common USB ethernet cards to make it more
likely the default config allows booting for network and enable XHCI on
SMDK5420 which has it defined in the dts but not in its config.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Prepare v2015.01-rc4

Signed-off-by: Tom Rini <trini@ti.com>

buildman: Fix some typos in README

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>

Fix hash verification

Fix issue in parse_verify_sum() which swaps handling of env-var and *address.
Move hash_command() argc check earlier.
Cosmetic change on do_hash() variable declaration.
Improved help message for "hash" command.

Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Simon Glass <sjg@chromium.org>

common/board_f.c: fix compile error when tracing disabled

When CONFIG_TRACE is disabled, linking fails with:

common/built-in.o:(.data.init_sequence_f+0x8): undefined reference to `trace_early_init'

To fix, wrap the call to trace_early_init() with #ifdef CONFIG_TRACE.

Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>

bcm281xx: add support for "USB OTG clock"

enable this clock with the following:
  clk_usb_otg_enable((void *)HSOTG_BASE_ADDR)

Signed-off-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>

initcall: add explicit hint if initcall was relocated

Commit "initcall: Improve debugging support" makes sense and indeed
simplifies process of matching initcalls executed with static
disassembly.

Until you are debugging relocation functionality.

Existign output may make you think that at some point execution somehow
returned back to non-relocated area. And there're many reasons/problems
that may provoke this behavior.

In order to make things clear let's add explicit mention in case initall
was actually relocated like this:
--->---
initcall: 810015f8
Relocation Offset is: 0efcf000
Relocating to 8ffcf000, new gd at 8fdced3c, sp at 8fdced20
initcall: 810015b8
initcall: 8ffd093c
initcall: 8ffd0a14
initcall: 81001940 (relocated to 8ffd0940)
initcall: 81001958 (relocated to 8ffd0958)
--->---

Note "unexpected" jump from 0x8f... area to 0x81... area.
Without explanation this raises many questions: execution jumped in
relocated area right as expected and then for some reason returned back?

But I hope comment in brackets will save some time for those curious
developers who are careful enough to catch "unexpected jump to pre-reloc
area" or those unlucky ones who'll have to deal with relocation
debugging.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>

scripts: fix binutils-version.sh

The current binutils-version.sh expects the version string at the end
of the first line.  It turned out to not work with Linaro toolchain:
It has "Linaro 2014.09" at the back.

To fix this issue, let's parse the word right after the close
parenthesis.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: York Sun <yorksun@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>

ARM: rpi: consolidate board rev error checking

Create a fake model table entry with default values, so we can error
check the board rev value once when querying it from the firmware, rather
than error-checking for invalid board rev values every time the model
table is used.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

ARM: rpi: support model A+

Add a board rev entry for the new model A+, and augment the board
rev error handling code to be a bit more verbose.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

ARM: rpi: only set usbethaddr on relevant systems

Model A and CM RPis don't have an on-board USB Ethernet device. Hence,
there's no point setting $usbethaddr based on the device fuses. Use the
model detection code to gate this. Note that the fuses are actually
programmed even on those devices though.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

vexpress64: switch to generic board

The few Versatile Express ARMv8 platforms we have may just as
well be switched to generic board from the beginning.

Tested on the ARM foundation model and the in progress support
for the ARMv8 Juno board.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>

vexpress64: take over maintenance of the semi vexpress64

As agreed with Steve Rae I'm taking over maintenance of the
semihosted, emulated FVP/foundation model Versatile Express
64 bit board variant.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>

arm: semihosting: get rid of forward declarations

By rearranging the functions in the semihosting code we can
avoid forward-declaration of the internal static functions.
This puts the stuff in a logical order: read/open/close/len
and then higher-order functions follow at the end.

Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

arm: semihosting: fix up compile bugs

There is currently a regression when using newer ARM64 compilers
for semihosting: the way long types are inferred from context
is no longer the same.

The semihosting runtime uses long and size_t, so use this
explicitly in the semihosting code and interface, and voila:
the code now works again.

Tested with aarch64-linux-gnu-gcc: Linaro GCC 4.9-2014.09.

Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Suggested-by: Mark Hambleton <mark.hambleton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

arm: semihosting: staticize internal functions

The semihosting code exposes internal file handle handling
functions to read(), open(), close() and get the length of
a certain file handle.

However the code using it is only interested in either
reading and entire named file into memory or getting the
file length of a file referred by name. No file handles
are used.

Thus make the file handle code internal to this file by
removing these functions from the semihosting header file
and staticize them.

This gives us some freedom to rearrange the semihosting
code without affecting the external interface.

Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge branch 'rmobile' of git://git.denx.de/u-boot-sh

arm: rmobile: kconfig: Remove '+S:' prefix from defconfig files

'+S' is unnecessary because boards of rmobile do not use SPL.
This removes from armadillo-800eva and kzm9g.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: exynos: clock: support SPLL as mmc source clock for exynos5420

MMC of exynos5420 can select SPLL as source clock, so add to support
SPLL in exynos5420_get_mmc_clk(). It was tested on Odroid-XU3 board.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

ARM: exynos5420: Leave VBUS GPIO configuration up to common code

Since commit 4a271cb1b4ffdf330 (exynos: usb: Switch USB VBUS GPIOs to be
device tree configured) it's not needed for the board specific files to
turn on the VBUS GPIO by hand as that gets done based on device tree. So
drop the redundant code from the SMDK5420 board file.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

odroid-XU3: Add entry for DTS EHCI GPIO

Add samsung,vbus-gpio information for the XU3. This allows the usage of
the EHCI controller on the XU3, which is connected to the SMSC LAN9514
chip (usb hub + network).

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

exynos5420: fix compilation without parade video

Not all exynos 5420 based devices with an LCD also have a parade LVDS
bridge. So make sure compilation doesn't break if CONFIG_LCD is enabled
and CONFIG_VIDEO_PARADE is not.

As a side-effect move the parade functions from the exynos system header
file to its own file.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Exynos5800: The Peach-Pi board does not have a Parade video bridge

Unlike the Peach-Pit board, there is no parade edp to lvds bridge on the
Pi. So drop it from  device-tree

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Odroid-XU3: Add documentation for Odroid-XU3

This patch adds documentation for Odroid-XU3. This documentation is
based on that of Odroid (doc/README-odroid) made by Przemyslaw Marczak.
The documentation includes basic information about boot media layout,
environment, partition layout, and the instruction to burn the u-boot
image to boot media.

Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Odroid-XU3: Add support for Odroid-XU3

This patch adds support for Odroid-XU3.

Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

config: exynos5420: move non common configs to specific board files

The media for boot and environment is a board-specific feature, not a
processor-specific. This is same to console port number and  some
other addresses. This patch moves the that kinds of configs to each
board-specific files from the common config file for Exynos5420.

Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

arm: socfpga: Change watchdog timeout

The current current watchdog timeout of 12 seconds is a bit small for
booting into Linux, especially when using a NFS based rootfs. So lets
change this timeout to a more defensive value of 30 seconds.

Also we now call the hw_watchdog_init() function so that we override
the value already configured from the Preloader.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>

Merge git://git.denx.de/u-boot-x86

arm: mxs: olinuxino: move DRAM config tuning to SPL

The weak mxs_adjust_memory_params function is called from spl_mem_init.c,
so it must be linked into the SPL to have an effect. Move it from
mx23_olinuxino.c to spl_boot.c.

This change was verified by reading back the register values.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

mx51evk: Fix MX51EVK_USB_CLK_EN_B definition

As per the mx51evk schematics MX51EVK_USB_CLK_EN_B is GPIO2_1, not GPIO2_2.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

arm: mx6: gw_ventana: Change clock init to enable NAND related clocks

Otherwise NAND booting is likely to fail. Since this disables the NAND related
clocks and SPL can't load the main U-Boot from NAND.

This problem was introduced with this patch:

e25fbe3f (gw_ventana: Move the DCD settings to spl code)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

ot1200: enable support for USB_STORAGE

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>

ot1200: add fsuuid command

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>