Wolfgang Denk [Fri, 26 Aug 2011 10:27:58 +0000 (10:27 +0000)]
MPC8xx: fix build problem for ETX094 board
Commit
7616e78 "Add Ethernet hardware MAC address framework to usbnet"
increased the code size and broke building for the ETX094 board.
Adjust the linker script to make it build again.
While we are at it, remove unused u-boot.lds.debug
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 24 Jul 2011 21:39:10 +0000 (21:39 +0000)]
phy.c: make less verbose - turn printf() into debug()
The PHY driver was too verbose and corrupted the boot message display
like this:
...
Net: TSEC0 connected to Marvell 88E1111S
TSEC1 connected to Marvell 88E1111S
TSEC0, TSEC1
...
Turn printf() into debug() so we het the expected output again:
...
Net: TSEC0, TSEC1
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Fri, 26 Aug 2011 13:55:03 +0000 (15:55 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
* 'master' of git://git.denx.de/u-boot-sh:
sh: add calling mmc_initialize in board.c
sh: sh7757lcr: Add KEEP order to start.o section
usb: r8a66597: Fix argument mistake of inl
sh: Clean up rsk7264 board settings
sh: sh2a: Add sh2a optimize to config.mk
sh: Fix rsk7203 alignment problem
sh: Add support for SH2A freestanding build
sh: Add Renesas rsk7264 board
Wolfgang Denk [Fri, 26 Aug 2011 13:54:14 +0000 (15:54 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ubi
* 'master' of git://git.denx.de/u-boot-ubi:
ubifs: Fix bad free() sequence in ubifs_finddir()
Yoshihiro Shimoda [Tue, 5 Jul 2011 08:18:38 +0000 (17:18 +0900)]
sh: add calling mmc_initialize in board.c
Some SH have MMC controller. So, if we need it, we have to call
the mmc_initialize().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Yoshihiro Shimoda [Tue, 5 Jul 2011 08:15:16 +0000 (17:15 +0900)]
sh: sh7757lcr: Add KEEP order to start.o section
The sh7757lcr has a local u-boot.lds because the sh7757lcr is only
supported the SPI booting.
This patch refers from the commit "sh: Add KEEP order to start.o section"
(commit ID:
b52da2aed8c2c388661f369052a97d5b5c9ed00a).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 27 Jun 2011 07:07:37 +0000 (16:07 +0900)]
usb: r8a66597: Fix argument mistake of inl
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Phil Edworthy [Thu, 9 Jun 2011 15:22:43 +0000 (16:22 +0100)]
sh: Clean up rsk7264 board settings
Adjusted default settings so that we can boot zImages and uImages.
Removed unused settings, use default commands and where possible
calculate all other settings.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 9 Jun 2011 06:03:34 +0000 (15:03 +0900)]
sh: sh2a: Add sh2a optimize to config.mk
Only the optimization of sh2 had been supported up.
This adds the optimization of sh2a.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Phil Edworthy [Tue, 31 May 2011 08:51:42 +0000 (01:51 -0700)]
sh: Fix rsk7203 alignment problem
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Phil Edworthy [Thu, 2 Jun 2011 22:15:27 +0000 (22:15 +0000)]
sh: Add support for SH2A freestanding build
SH2A toolchains often only provide an fdpic version of libgcc. This
can't be used with bare-metal software like U-Boot, so this patch
provides the necessary functions extracted from libgcc.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Phil Edworthy [Wed, 1 Jun 2011 06:35:13 +0000 (07:35 +0100)]
sh: Add Renesas rsk7264 board
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Wolfgang Denk [Thu, 28 Jul 2011 13:27:22 +0000 (15:27 +0200)]
ubifs: Fix bad free() sequence in ubifs_finddir()
Free private_data member element before freeing file structure.
This was causing malloc to crash. Also remove unnecessary variable
assigments as file structure gets free'd as well.
Signed-off-by: Rod Boyce <uboot@teamboyce.co.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Jason Cooper [Sun, 31 Jul 2011 20:09:58 +0000 (20:09 +0000)]
usb: increase non-bulk timeout for slow chipsets.
If you take a look at
96820a35, you'll see the original timeout was
CONFIG_SYS_HZ. Which is 1000. After the mentioned change, non-bulk timeout
was changed to 100. This causes timeout failures on the dreamplug platform
when trying to initialize the usb microsd reader.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Tue, 12 Jul 2011 00:16:46 +0000 (02:16 +0200)]
USB: Move USB_PRINTF() out of ifdef in usb_scan_devices()
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Tue, 12 Jul 2011 00:16:47 +0000 (02:16 +0200)]
USB: Set portnr so USB1.1 and 1.0 devices work on EHCI controllers
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Nobuhiro Iwamatsu [Mon, 11 Jul 2011 02:03:47 +0000 (11:03 +0900)]
usb: r8a66597: Fix argument mistake of inl
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Simon Glass [Mon, 13 Jun 2011 23:13:12 +0000 (16:13 -0700)]
Put common autoload code into auto_load() function
This is a small clean-up patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
Simon Glass [Mon, 13 Jun 2011 23:13:11 +0000 (16:13 -0700)]
Add documentation for USB Host Networking
This describes what it is for, devices supported, how to enable for your
board in U-Boot, setting up the server, and notes about MAC addresses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
Simon Glass [Mon, 13 Jun 2011 23:13:10 +0000 (16:13 -0700)]
Add Ethernet hardware MAC address framework to usbnet
Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).
This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
Simon Glass [Mon, 13 Jun 2011 23:13:09 +0000 (16:13 -0700)]
Add support for SMSC95XX USB 2.0 10/100MBit Ethernet Adapter
The SMSC95XX is a USB hub with a built-in Ethernet adapter. This adds support
for this, using the USB host network framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
Albert ARIBAUD [Thu, 4 Aug 2011 16:45:45 +0000 (18:45 +0200)]
Convert ISO-8859 files to UTF-8
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Anatolij Gustschin [Mon, 1 Aug 2011 04:16:29 +0000 (04:16 +0000)]
mpc5200: digsy_mtc: fix extension board EEPROM I2C address for rev5
On newer rev5 hardware the extension board EEPROM I2C address
has been changed to 0x54. Make this I2C address configurable
depending on CONFIG_DIGSY_REV5 so that extention board presence
detection works correctly on newer hardware.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Heiko Schocher [Mon, 1 Aug 2011 04:01:43 +0000 (04:01 +0000)]
hwmon: do not init sensors on startup
The U-Boot Design Principles[1] clearly say:
Initialize devices only when they are needed within U-Boot, i.e. don't
initialize the Ethernet interface(s) unless U-Boot performs a download
over Ethernet; don't initialize any IDE or USB devices unless U-Boot
actually tries to load files from these, etc. (and don't forget to
shut down these devices after using them - otherwise nasty things may
happen when you try to boot your OS).
So, do not initialize and read the sensors on startup.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
Wolfgang Denk [Thu, 4 Aug 2011 21:05:07 +0000 (23:05 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
drivers/rtc: add Marvell Integrated RTC
Armada100: Add Board Support for Marvell GuruPlug-Display
Armada100: MFP macro naming correction
arm: auto gen asm-offsets.h for mb86r0x
spear: fix build errors for spear3xx/spear600 platforms
cosmetic: arm: lib/board.c: Coding Style cleanup
ARM: versatile: fix board support
SMDKV310: Enable device tree support
SMDKV310: MMC_SPL: Fix building when using "make O="
arm: a320: enable tagged list support
arm: a320: fix multiline comment style
ARMv7: u8500_href: Add missing header to fix compiler warning
Removed unused define, CONFIG_ARMV7.
avr32: add grasshopper (ICnova AP7000) board
AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
MAKEALL: remove AT91 boards that are in boards.cfg
AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
AT91: Board fix for AT91SAM9261-EK
AT91: SoC fix at91sam9261_matrix.h
AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
AT91: change common at91sam9261 files to compile with new scheme
AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
README: fix arm920t/at91 path
net/eth.c: drop obsolete at91rm9200 support
README.at91-soc: remove AT91(RM9200) joining notice
a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
MAKEALL: remove obsolete at91rm9200 soc
ARM: remove obsolete at91rm9200
omap4: clock init support for omap4460
omap4: support TPS programming
omap: reuse omap3 gpio support in omap4
omap4: sdram init changes for omap4460
omap4: add omap4460 revision detection
mkimage: Add OMAP boot image support
omap: add MMC and FAT support to SPL
omap: add basic SPL support
armv7: start.S: fixes and enhancements for SPL
omap4: automatic sdram detection
omap4: calculate EMIF register values
omap4: add sdram init support
omap4: add clock support
omap4: add OMAP4430 revision check
omap4: cleanup pin mux data
omap4: utility function to identify the context of hw init
DA8xx: fix LPSC constants
DA8xx: switch an enum to defines for consistency
DA8xx: add MMC/SD controller addresses
DaVinci EMAC: declare function for all DA8xx CPUs
DA8xx: add generic GPIO driver
DaVinci: rename gpio_defs.h to gpio.h
omap3evm: eth: Include functions only when necessary
omap3evm: Update ethernet reset sequence for Rev.G board
omap3evm: eth: split function setup_net_chip
omap3: Include array definition only when it is used
omap730p2: fix build breaks
omap2420h4: fix build breaks
omap1610inn: fix build breaks
omap1510inn: fix build breaks
omap5912osk: fix build breaks
omap1610h2: fix build breaks
Anatolij Gustschin [Sat, 16 Jul 2011 20:28:23 +0000 (22:28 +0200)]
video: mb862xx: change controller detection message
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Fri, 27 May 2011 14:08:20 +0000 (16:08 +0200)]
video: mb862xx: support Coral-PA controller
Add detection of Coral-PA and configure Coral CCF an MMR parameters
using CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx_MMR macros.
Use CCF and MMR parameters for Coral-P Eval. Board if the appropriate
macros weren't defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Timur Tabi [Thu, 26 May 2011 14:02:17 +0000 (09:02 -0500)]
video: Add SHARP LQ084S3LG01 LCD support on P1022DS
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Jason Cooper [Thu, 4 Aug 2011 15:56:16 +0000 (21:26 +0530)]
drivers/rtc: add Marvell Integrated RTC
This driver can be used for kirkwood SoCs by enabling CONFIG_RTC_MV. Tested on
Global Scale Technologies Dreamplug.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Ajay Bhargav [Thu, 4 Aug 2011 15:56:02 +0000 (21:26 +0530)]
Armada100: Add Board Support for Marvell GuruPlug-Display
This patch adds basic board support with DRAM and UART functionality
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Ajay Bhargav [Thu, 4 Aug 2011 15:36:44 +0000 (21:06 +0530)]
Armada100: MFP macro naming correction
MFP macros for UART3 updated.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Albert ARIBAUD [Thu, 4 Aug 2011 16:59:59 +0000 (18:59 +0200)]
Matthias Weisser [Mon, 1 Aug 2011 05:11:52 +0000 (05:11 +0000)]
arm: auto gen asm-offsets.h for mb86r0x
auto gen asm-offsets.h for mb86r0x
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Shiraz Hashim [Sat, 11 Jun 2011 21:32:57 +0000 (21:32 +0000)]
spear: fix build errors for spear3xx/spear600 platforms
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Vipin Kumar <vipin.kumar@st.com>
Heiko Schocher [Fri, 15 Jul 2011 19:36:36 +0000 (19:36 +0000)]
cosmetic: arm: lib/board.c: Coding Style cleanup
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Albert Aribaud <albert.u.boot@aribaud.net>
cc: <macpaul@gmail.com>
cc: Wolfgang Denk <wd@denx.de>
Stefano Babic [Fri, 24 Jun 2011 03:04:38 +0000 (03:04 +0000)]
ARM: versatile: fix board support
Versatile board is used as example to run u-boot under qemu.
The patch fixes relocation for all versatile boards and adds
a versatileqemu target to be used under qemu.
Patch tested only under qemu, not on real boards.
Tested with QEMU emulator version 0.14.50.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Alessandro Rubini <rubini-list@gnudd.com>
CC: Loïc Minier <loic.minier@linaro.org>
Thomas Abraham [Fri, 3 Jun 2011 22:52:17 +0000 (22:52 +0000)]
SMDKV310: Enable device tree support
Enable passing a flattened device tree to the kernel.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Chander Kashyap [Thu, 2 Jun 2011 18:07:32 +0000 (18:07 +0000)]
SMDKV310: MMC_SPL: Fix building when using "make O="
Fixes dependency build error with "make O=" option.
"make O=" option is used to specify output directory.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Po-Yu Chuang [Mon, 18 Jul 2011 16:56:53 +0000 (16:56 +0000)]
arm: a320: enable tagged list support
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Po-Yu Chuang [Mon, 18 Jul 2011 16:55:39 +0000 (16:55 +0000)]
arm: a320: fix multiline comment style
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Dirk Behme [Sat, 9 Jul 2011 20:52:17 +0000 (20:52 +0000)]
ARMv7: u8500_href: Add missing header to fix compiler warning
Fix the compiler warning
u8500_href.c: In function 'hrefplus_mmc_power_init':
u8500_href.c:258: warning: implicit declaration of function 'prcmu_i2c_read'
u8500_href.c:265: warning: implicit declaration of function 'prcmu_i2c_write'
by adding the missing header file.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Christopher Harvey [Thu, 7 Jul 2011 04:37:55 +0000 (04:37 +0000)]
Removed unused define, CONFIG_ARMV7.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Andreas Bießmann [Thu, 30 Jun 2011 22:03:20 +0000 (22:03 +0000)]
avr32: add grasshopper (ICnova AP7000) board
The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit
GmbH.
See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html
for detailed information about this device.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Reinhard Meyer [Tue, 2 Aug 2011 15:09:55 +0000 (15:09 +0000)]
AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Reinhard Meyer [Tue, 2 Aug 2011 13:31:11 +0000 (13:31 +0000)]
MAKEALL: remove AT91 boards that are in boards.cfg
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Xu, Hong [Fri, 10 Jun 2011 21:31:26 +0000 (21:31 +0000)]
AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Xu, Hong [Fri, 10 Jun 2011 21:31:25 +0000 (21:31 +0000)]
AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
Rework for AT91SAM9263 SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Xu, Hong [Sun, 31 Jul 2011 22:49:00 +0000 (22:49 +0000)]
AT91: Board fix for AT91SAM9261-EK
Fix board part of AT91SAM9261-EK according to the new scheme
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Xu, Hong [Sun, 31 Jul 2011 22:37:06 +0000 (22:37 +0000)]
AT91: SoC fix at91sam9261_matrix.h
Fix at91sam9261_matrix.h according to the new scheme.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Xu, Hong [Mon, 1 Aug 2011 03:56:53 +0000 (03:56 +0000)]
AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Xu, Hong [Mon, 1 Aug 2011 03:56:32 +0000 (03:56 +0000)]
AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
Rework for AT91SAM9RL SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: US->USART, cosmetics
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Asen Dimov [Tue, 26 Jul 2011 01:23:39 +0000 (01:23 +0000)]
AT91: change common at91sam9261 files to compile with new scheme
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Reinhard Meyer [Mon, 25 Jul 2011 21:56:04 +0000 (21:56 +0000)]
AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
Bits 0..3 in cs_mask = CS0..CS3 in SPI mode require it to be peripheral
Bits 4..7 in cs_mask = CS0..CS3 in GPIO mode require it to be output
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Andreas Bießmann [Mon, 18 Jul 2011 09:57:45 +0000 (09:57 +0000)]
a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
The CONFIG_AT91RM9200_USART is an remnant of
18ed5e9550810e2fc5bf2c757aee47774609651c which deleted the
at91rm9200_usart driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Mon, 18 Jul 2011 09:41:08 +0000 (09:41 +0000)]
README: fix arm920t/at91 path
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Mon, 18 Jul 2011 09:41:07 +0000 (09:41 +0000)]
net/eth.c: drop obsolete at91rm9200 support
All available at91rm9200 boards have migrated to ar920t/at91 and
therefore to CONFIG_NET_MULTI.
The obsolete at91rm9200_miiphy_initialize() was removed in "ARM: remove
obsolete at91rm9200".
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Mon, 18 Jul 2011 09:41:06 +0000 (09:41 +0000)]
README.at91-soc: remove AT91(RM9200) joining notice
Since all currently supported at91rm9200 boards are migrated to at91
support the joining notice can be removed.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Mon, 18 Jul 2011 09:41:05 +0000 (09:41 +0000)]
a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
The CONFIG_AT91_LEGACY warning became obsolete due to complete removal of
at91rm9200 arch code in arm920t.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Mon, 18 Jul 2011 09:41:04 +0000 (09:41 +0000)]
MAKEALL: remove obsolete at91rm9200 soc
Since complete at91rm9200 SoC device was droped (due to replacement with
common at91 code) this parameter can safely be removed.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Mon, 18 Jul 2011 09:41:03 +0000 (09:41 +0000)]
ARM: remove obsolete at91rm9200
The big "ARM: remove broken boards" series deletes all boards using
obsolete arm920t/at91rm9200 arch code. Therefore we can safely remove
this code now.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Aneesh V [Thu, 21 Jul 2011 13:29:36 +0000 (09:29 -0400)]
omap4: clock init support for omap4460
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:29:32 +0000 (09:29 -0400)]
omap4: support TPS programming
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:29:29 +0000 (09:29 -0400)]
omap: reuse omap3 gpio support in omap4
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:29:26 +0000 (09:29 -0400)]
omap4: sdram init changes for omap4460
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:29:23 +0000 (09:29 -0400)]
omap4: add omap4460 revision detection
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
John Rigby [Thu, 21 Jul 2011 13:10:30 +0000 (09:10 -0400)]
mkimage: Add OMAP boot image support
- Add mkimage support for OMAP boot image
- Add support for OMAP boot image(MLO) generation in the new
SPL framework
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:27 +0000 (09:10 -0400)]
omap: add MMC and FAT support to SPL
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
payload size and load address from this header. If the
header is not detected assume u-boot.bin as payload
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:21 +0000 (09:10 -0400)]
omap: add basic SPL support
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:18 +0000 (09:10 -0400)]
armv7: start.S: fixes and enhancements for SPL
- Allow SPL to have .bss disjoint from rest of the image
- Allow for .bss setup in CONFIG_SPL_BUILD case too.
- Take care of the special case where relocation offset = 0.
- Compile out exception handling code and install a simpler
vector
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:15 +0000 (09:10 -0400)]
omap4: automatic sdram detection
Identify SDRAM devices connected to EMIF automatically:
LPDDR2 devices have some Mode Registers that provide details
about the device such as the type, density, bus width
etc. EMIF has the capability to read these registers. If there
are no devices connected to a given chip-select reading mode
registers will return junk values. After reading as many such
registers as possible and matching with expected ranges of
values the driver can identify if there is a device connected
to the respective CS. If we identify that a device is connected
the values read give us complete details about the device.
This along with the base AC timings specified by JESD209-2
allows us to do a complete automatic initialization of
SDRAM that works on all boards.
Please note that the default AC timings specified by JESD209-2
will be safe for all devices but not necessarily optimal. However,
for the Elpida devices used on Panda and SDP the default timings
are both safe and optimal.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:12 +0000 (09:10 -0400)]
omap4: calculate EMIF register values
Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.
For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:09 +0000 (09:10 -0400)]
omap4: add sdram init support
Add support for the SDRAM controller (EMIF).
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:07 +0000 (09:10 -0400)]
omap4: add clock support
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails
This work draws upon previous work done for x-loader by:
Santosh Shilimkar <santosh.shilimkar@ti.com>
Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:04 +0000 (09:10 -0400)]
omap4: add OMAP4430 revision check
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:10:01 +0000 (09:10 -0400)]
omap4: cleanup pin mux data
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Aneesh V [Thu, 21 Jul 2011 13:09:59 +0000 (09:09 -0400)]
omap4: utility function to identify the context of hw init
The basic hardware init of OMAP4(s_init()) can happen in 4
different contexts:
1. SPL running from SRAM
2. U-Boot running from FLASH
3. Non-XIP U-Boot loaded to SDRAM by SPL
4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
Configuration Header feature
What level of hw initialization gets done depends on this
context. Add a utility function to find this context.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Laurence Withers [Mon, 18 Jul 2011 13:53:23 +0000 (09:53 -0400)]
DA8xx: fix LPSC constants
Some of the LPSC constants were incorrect, and some were missing. This
commit fixes the incorrect constants (which were not used anywhere in
the tree) and adds all constants for both DA830 and DA850, as per the
TI datasheets.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Laurence Withers [Mon, 18 Jul 2011 13:53:19 +0000 (09:53 -0400)]
DA8xx: switch an enum to defines for consistency
There are two main sets of LPSC constants, depending on the processor
family. The DA8xx constants were given in an enum whereas the non-DA8xx
constants were preprocessor defines. This commit switches the DA8xx
constants to defines for consistency.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Laurence Withers [Mon, 18 Jul 2011 13:53:17 +0000 (09:53 -0400)]
DA8xx: add MMC/SD controller addresses
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Laurence Withers [Mon, 18 Jul 2011 13:53:14 +0000 (09:53 -0400)]
DaVinci EMAC: declare function for all DA8xx CPUs
The function davinci_emac_mii_mode_sel() is defined in
board/davinci/common/misc.c for any DA8xx CPU which has
CONFIG_DRIVER_TI_EMAC enabled. However, the prototype was only being
declared in <include/asm/arch/davinci_misc.h> for the DA850 EVM board.
This patch declares it for all DA8xx CPUs where CONFIG_DRIVER_TI_EMAC
is enabled.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Laurence Withers [Mon, 18 Jul 2011 13:26:01 +0000 (09:26 -0400)]
DA8xx: add generic GPIO driver
Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Laurence Withers [Mon, 18 Jul 2011 13:25:58 +0000 (09:25 -0400)]
DaVinci: rename gpio_defs.h to gpio.h
In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Sanjeev Premi [Mon, 18 Jul 2011 13:23:00 +0000 (09:23 -0400)]
omap3evm: eth: Include functions only when necessary
These functions are not required when CONFIG_CMD_NET
is not defined:
- setup_net_chip()
- reset_net_chip()
- board_eth_init()
This patch wraps them in #ifdef CONFIG_CMD_NET...#endif
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Sriramakrishnan [Mon, 18 Jul 2011 13:21:55 +0000 (09:21 -0400)]
omap3evm: Update ethernet reset sequence for Rev.G board
The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.
The patch uses generic gpio API instead of direct access
to corresponding registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Sanjeev Premi [Mon, 18 Jul 2011 13:20:15 +0000 (09:20 -0400)]
omap3evm: eth: split function setup_net_chip
In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.
The patch moves the reset actions to new function reset_net_chip().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Sanjeev Premi [Mon, 18 Jul 2011 13:12:24 +0000 (09:12 -0400)]
omap3: Include array definition only when it is used
The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().
Enclose definition of this array in #ifdef...#endif for
the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Matthias Weisser [Wed, 29 Jun 2011 11:57:25 +0000 (13:57 +0200)]
video: Use memset instead of loop
There is a optimized version of memset in u-boot available so use it instead
of the hand written loop version.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Wolfgang Denk [Tue, 2 Aug 2011 20:39:36 +0000 (22:39 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
* 'master' of git://git.denx.de/u-boot-mmc:
Revert "AT91:mmc:fix multiple read/write error"
Simon Guinot [Mon, 2 May 2011 11:01:38 +0000 (11:01 +0000)]
sf: macronix: disable write protection when initializing
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Shaohui Xie [Wed, 20 Apr 2011 20:07:11 +0000 (20:07 +0000)]
sf: spansion: add support for S25FL129P_64K
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Macpaul Lin [Wed, 20 Apr 2011 16:51:39 +0000 (16:51 +0000)]
mtd/spi/macronix.c: add MX25L4005 and MX25L8005
Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf
This patch has been tested with MX25L4005 and MX25L8005
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Wolfgang Denk [Tue, 2 Aug 2011 19:52:21 +0000 (21:52 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
net/4xx: Install interrupt handler after driver registration
Wolfgang Denk [Tue, 2 Aug 2011 19:46:53 +0000 (21:46 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: jtag-console: fix timer usage
Blackfin: switch to common display_options()
Blackfin: serial: move early debug strings into .rodata section
Blackfin: adi boards: also set stderr to nc with helper
Blackfin: update anomaly lists to latest public info
Blackfin: serial: convert to bfin_{read,write} helpers
Blackfin: split out async setup
Blackfin: adi boards: enable pretty flash progress output
Blackfin: drop unused dma.h header from start code
Blackfin: portmux: allow header to be included in assembly files
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
Blackfin: sync MMR read/write helpers with Linux
Blackfin: gpio: optimize free path a little
Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
Blackfin: uart: fix printf warning
Blackfin: add init.elf helper code
Blackfin: dont reset SWRST on newer bf526 parts
Blackfin: adi boards: enable multi serial support by default
Blackfin: uart: add multiple serial support
Blackfin: uart: move debug buffers into local bss
Wolfgang Denk [Tue, 2 Aug 2011 19:45:45 +0000 (21:45 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
* 'master' of git://git.denx.de/u-boot-mips:
README: update MIPS related informations
MIPS: make cache operation mode configurable
MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFG
MIPS: INCA-IP: rename inca-swap-bytes host tool
Wolfgang Denk [Sat, 30 Jul 2011 21:50:50 +0000 (23:50 +0200)]
tqm834x.c: fix compiler warning
Fix:
tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards
qualifiers from pointer target type
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Sat, 30 Jul 2011 14:01:08 +0000 (14:01 +0000)]
environment.h: fix warning: "CONFIG_ENV_IS_EMBEDDED" redefined
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sat, 30 Jul 2011 13:33:49 +0000 (13:33 +0000)]
fpga: constify to fix build warning
Fix compiler warning:
cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type
Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
Wolfgang Denk [Sat, 30 Jul 2011 12:32:45 +0000 (12:32 +0000)]
Unify timer_init() and cpu_init() prototypes
Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
seedshope [Sat, 30 Jul 2011 07:28:49 +0000 (07:28 +0000)]
ARM: fix error: conflicting types for 'setenv'
Also remove bogus comment.
Signed-off-by: Zhong hongbo <bocui107@gmail.com>
Changed commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Wolfgang Denk [Sat, 30 Jul 2011 12:48:09 +0000 (12:48 +0000)]
cfb_console.c: checkpatch cleanup
Fix the following:
ERROR: do not initialise statics to 0 or NULL
ERROR: do not use assignment in if condition
Signed-off-by: Wolfgang Denk <wd@denx.de>
projects / oweals / u-boot.git / log