ARM: highbank: Add boot counter support

Add boot counter support using an sysreg which is persistent across reset.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

ARM: highbank: change TEXT_BASE to 0x8000

Make some space at the beginning of RAM so the FDT can be loaded to a
known fixed address at 0x1000.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

ARM: highbank: fix us_to_tick calculation

udelay calls were off due to failing to convert us to ns. Fix this and drop
the unnecessary shifts since NS_PER_TICK is only 7ns.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

ARM: highbank: add missing get_tbclk

The get_tbclk function was missing and the recent commit "common: add
possibility for readline_into_buffer timeout" makes it required.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

ARM: highbank: fix warning for calxedaxgmac_initialize

Add include of netdev.h to pick-up declaration of calxedaxgmac_initialize.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

net: calxedaxgmac: fix build due to missing __aligned definition

Include linux/compiler.h to fix build error due to missing __aligned
definition.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

EXYNOS: Add structure for Exynos4 DMC

Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC).

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

EXYNOS: SMDK5250: Support all 4 UARTs

This properly configures the mux to enable all UARTs.

This also fixes things so that we don't configure balls XUCTSN_1 and
XURTSN_1 as UART1 configuration (RTS/CTS), since they aren't
connected.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Chander kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

ARM: fix s3c2410 timer code

This patch fixes the s3c24x0 timer code to work with the ARM
relocation feature.

Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

ARM: davinci: fixes for cam_enc_4xx board

- change CONFIG_ENV_RANGE to contain 2 nand erase blocks,
  one for bad block reserve.
- remove from the envvariable "img_writeramdisk" the
  ubifsmount command, as it is not needed.
- erase the hole mtd partition containing u-boot
- save environment variable "dvn_app_vers" and "dvn_boot_vers"
  only after installing the new image.
changes requested from Marek Vasut:
- arm, davinci: fix eldk-4.2 warnings for cam_enc_4xx board
  - get rid of run_command2 usage
    needed since patch:
    commit 009dde1955583e306cf904c864068f3acb0db499
    Author: Simon Glass <sjg@chromium.org>
    Date:   Tue Feb 14 19:59:20 2012 +0000

    Rename run_command2() to run_command()
    is now in mainline.
  - add CONFIG_SPL_LIBGENERIC_SUPPORT support
  - remove CONFIG_CMD_PXE support
  - fix warning:
    cam_enc_4xx.c: In function 'menu_handle':
    cam_enc_4xx.c:609: warning: dereferencing type-punned pointer
    will break strict-aliasing rules
  - fix error:
    arm-linux-ld: u-boot-spl: Not enough room for program headers,
    try linking with -N

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Fletzer Martin <Martin.Fletzer@ait.ac.at>
Cc: Wolfgang Denk <wd@denx.de>

omap3_spi: receive transmit mode

Implementation of receive-transmit mode for
omap3 MCSPI.

Introduces full duplex communication, needed by
some spi devices (such as enc28j60).

Signed-off-by: jacopo mondi <mondi@cs.unibo.it> <j.mondi@voltaelectronics.com>

calimain, enbw_cmc: Fix typo in comments

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>

Davinci: ea20: use gpio framework to access gpios

Drop direct access to SOC's registers and use
the function of the GPIO driver for da8xx.

[Tom: Remove gpio[68]_base as it's now unused]

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: dzu@denx.de
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

OMAP3: mt_ventoux: sets its own mtdparts

Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>

OMAP3: mt_ventoux: updated timing for FPGA

Fix chipselect timing for FPGA

Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>

twl4030: fix potential power supply handling issues

twl4030_pmrecv_vsel_cfg currently first sets up device group (effectively
enabling the supply), and only then sets vsel (selects voltage). This could
lead to wrong voltage for a short time, or even long time if second i2c
write fails.

Fix this by writing vsel first and device group after that. Also
introduce error checking to not enable the supply if we failed to set
the voltage, and start logging errors as power supply problems are
usually important.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>

NAND: TI: fix warnings in omap_gpmc.c

The following warnings are reported for boards using SOFT ECC.

omap_gpmc.c:33:30: warning: 'hw_nand_oob' defined but not used
omap_gpmc.c:78:13: warning: 'omap_hwecc_init' defined but not used
omap_gpmc.c:116:12: warning: 'omap_correct_data' defined but not used
omap_gpmc.c:182:12: warning: 'omap_calculate_ecc' defined but not used
omap_gpmc.c:208:13: warning: 'omap_enable_hwecc' defined but not used

Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>

cam_enc_4xx: Rename 'images' to 'imgs'

To avoid a conflict with common/cmd_bootm.c's 'images' (which is
exposed as part of the Linux SPL series), rename the board-specific
'images' to 'imgs'.

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>

arm: Add Prep subcommand support to bootm

Adds prep subcommand to bootm implementation of ARM. When bootm is called
with the subcommand prep the function stops right after ATAGS creation and
before announce_and_cleanup.

This is used in command "cmd_spl export"

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>

OMAP3: twister: add support to boot Linux from SPL

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>

SPL: call cleanup_before_linux() before booting Linux

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>

OMAP3: SPL: do not call I2C init if no I2C is set.

Call i2c initialization in spl_board_init only if I2C
is configured for the board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>

Add cache functions to SPL for armv7

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>

devkit8000: Implement and activate direct OS boot

- Implements spl_start_uboot() for devkit8000
- Add configs to activate direct OS boot from SPL

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

omap/spl: change output of spl_parse_image_header

This only outputs "Assuming u-boot.bin..." if debug is active.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

omap-common/spl: Add linux boot to SPL

This adds Linux booting to the SPL

This depends on CONFIG_MACH_TYPE patch by Igor Grinberg
(http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809)

Related CONFIGs:
CONFIG_SPL_OS_BOOT
Activates/Deactivates the OS booting feature
CONFIG_SPL_OS_BOOT_KEY
defines the IO-pin number u-boot switch - if pressed u-boot is
booted
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
Address where the kernel boot arguments are expected - this is
normaly RAM-begin + 0x100

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

devkit8000/spl: init GPMC for dm9000 in SPL

Linux crashes if the GPMC isn't configured for the dm9000.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

omap-common: Add NAND SPL linux booting

This implements booting of Linux from NAND in SPL

Related config parameters:
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
Address where the kernel boot arguments are expected - this is
normally RAM-start + 0x100 (on ARM)

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

devkit8000: add config for spl command

This adds some configs for devkit8000 to use the new spl command

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Add cmd_spl command

This adds a spl command to the u-boot.

Related config:
CONFIG_CMD_SPL
activate/deactivate the command
CONFIG_CMD_SPL_NAND_OFS
Offset in NAND to use

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>

mx53ard: Initialize return code with error

The variable "rc" is the return of board_eth_init() function. Initialize
it with an error code, so that this function can return an error when
CONFIG_SMC911X is not set.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

mx53: Make PLL2 to be the parent of UART clock

Change the parent UART clock to be PLL2, so that U-boot can also boot
a Freescale 2.6.35 kernel for mx53.

FSL kernel and U-boot changed the UART parent from PLL3 to PLL2 to avoid
conflicts with IPU clocks, so that the video resolution can be changed
without affecting the UART clock.

On a 2.6.35 kernel the serial console is messed up after IPU driver is loaded
and this patch fixes this problem.

Tested on a mx53loco board booting a FSL kernel and also a mainline kernel.

Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

configs: imx: Use CONFIG_SF_DEFAULT_CS

CONFIG_SPI_FLASH_CS is not used anywhere.

Use CONFIG_SF_DEFAULT_CS instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx28evk: Provide default values for SPI bus and chip select

Provide default values for SPI bus and chip select.

This allows the command "sf probe" to work without passing SPI bus and chip
select numbers as arguments.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>

USB: ehci-mx6: Add proper IO accessors

Add proper IO accessors for mx6 usb registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>

mx6: Read silicon revision from register

Instead of hardcoding the mx6 silicon revision, read it in run-time.

Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.

Tested on a mx6qsabrelite, where it shows:

CPU:   Freescale i.MX6Q rev1.0 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>

i.MX28: Drop __naked function from spl_mem_init

Instead of compiling the function and using the result as a constant, simply use
the constant.

NOTE: This patch works around bug:

  http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>

mxs_spi: Return proper timeout error

Instead of returning -1, it is preferred to return -ETIMEDOUT in case of timeouts.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>

i.MX28: Make the stabilization delays shorter

Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be
enough according to the datasheet and bootlets.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>

pmic_i2c: Return error in case of invalid pmic_i2c_tx_num

Return error in case of invalid pmic_i2c_tx_num.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>

mx6: Remove duplicate definition of ANATOP_BASE_ADDR

Remove duplicate definition of ANATOP_BASE_ADDR.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

mx6: Fix reset cause for Power On Reset case

After booting mx6qsabrelite from POR the following is reported:

CPU:   Freescale i.MX61 family rev1.0 at 792 MHz
Reset cause: unknown reset

This is because both the POR and WDOG bits are set after reset.

Fix this by also checking both bits in the POR case.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE

Allow non-dt kernels to boot

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG

This is needed to support Freescale-supplied userspaces.

At the moment, both the IPU and VPU libraries provided by Freescale
in the "imx-lib" package contain routines which scrape the system
revision from /proc/cpuinfo. In the VPU library, this information is
used to load the proper firmware, allowing a single binary to be used
across various i.MX processors.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

i.MX28: Enable additional DRAM address bits

Enables all fourteen address lines for DRAM

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>

mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

mx31: add "ARM11P power gating" to get_reset_cause

Add missing reset reason 7 to get_reset_cause().

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>

mx31pdk: Fix CONFIG_SYS_MEMTEST_END

CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

efikamx: Fix CONFIG_SYS_MEMTEST_END

CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>

mx53smd: Fix CONFIG_SYS_MEMTEST_END

CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

mx53evk: Fix CONFIG_SYS_MEMTEST_END

CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

mx51evk: Fix CONFIG_SYS_MEMTEST_END

CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

i.MX6: mx6qsabrelite: add ext2 support

Current Ubuntu releases from Freescale contain a boot script in ext3 filesystem.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

imximage: Remove overwriting of flash_offset

The flash header supports different flash offsets for different
boot devices. E.g. parallel NOR or OneNAND use a different offset
than FLASH_OFFSET_STANDARD (== 0x400).

The flash offset is correctly read from the configuration in
parse_cfg_cmd(). But is then overwritten wrongly in set_imx_hdr_v1/2().

Fix this by removing this overwriting. Use the flash offset
correctly read from the configuration, instead.

If there is no flash_offset read from the configuration file, i.e.
the BOOT_FROM tag is missing, exit with an error message.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Liu <liu.h.jason@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>

IXP: Fix GPIO_INT_ACT_LOW_SET()

The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

IXP: Fix NAND build warning on PDNB3 and SCPU

nand.c: In function ‘pdnb3_nand_read_buf’:
nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
nand.c: In function ‘pdnb3_nand_dev_ready’:
nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]

Remove the 4-byte-at-time read mode altogether, the most is bogus and will
likely cause unaligned accesses.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

IXP: Move PDNB3 and SCPU from Makefile to boards.cfg

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

IXP: Squash warnings in IXP NPE

IxEthAcc.c: In function ‘ixEthAccInit’:
IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare]
IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’:
IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable]
IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’:
IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}

These symbols are no longer defined in Linux-ARM's mach-types files. Replace
these with CONFIG_MACH_TYPE instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

IXP: Make IXP buildable with arm-linux- toolchains

Add -EB flag to LD to switch endianness of the linker. This should make armeb
targets buildable again. Also, make use of U-Boot's internal libgcc instead of
toolchain's one, this works around the use of libraries from GCC, which might be
little endian.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

Examples: Properly append LDFLAGS to LD command

The LD command in examples/standalone/Makefile ignored platform specific
LDFLAGS setup. Pass these LDFLAGS to the command.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>

SPL: Enable YMODEM support on BeagleBone and AM335x EVM

Cc: Chandan Nath <chandan.nath@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Matt Porter <mporter@ti.com>

SPL: Add YMODEM over UART load support

Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.

Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

SPL: Add README.omap3

This document describes the SPL process for OMAP3 (and related) boards
as well as a partial memory map and how to verify certain aspects
outside of running on the target.

Signed-off-by: Tom Rini <trini@ti.com>

README: document more SPL config options

Signed-off-by: Tom Rini <trini@ti.com>

spl.c: Use __noreturn decorator

Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Rini <trini@ti.com>

config.mk: Check for -fstack-usage support

Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Rini <trini@ti.com>

config.mk: Make cc-option create a file under include/generated

Testing for -fstack-usage requires the creation of an output file, which
isn't possible with /dev/null.

Signed-off-by: Tom Rini <trini@ti.com>

.gitignore: Add .su files

The '-fstack-usage' option to gcc will generate .su files, ignore them.

Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Rini <trini@ti.com>

Fix erroneous 32-bit access to hw_clkctrl_frac0 and hw_clkctrl_frac1 registers

This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>

Introducing 8-bit wide register, mx28_register_8

This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>

Renamed mx28_register to mx28_register_32 to prepare for mx28_register_8

This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>

i.MX28: Reformat the DRAM memory configuration data

Reformat the data so it's easier to navigate through them.

Signed-off-by: Marek Vasut <marex@denx.de>

M28: Support for the old M28 SoM v1.0

This prototype version SoM is unused and not available to public.
Support this only for internal debugging purposes.

Signed-off-by: Marek Vasut <marex@denx.de>

M28: Fix LCD PINMUX

The LCD pins configuration was wrong in U-Boot, configure pins properly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>

mx6qsabrelite: add and enable USB Host 1 support

Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>

usb/ehci: Add USB support for the MX6Q

Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>

mx6q: mx6qsabrelite: Update the README

The SD loader binary is now downloadable at

https://wiki.linaro.org/Boards/MX6QSabreLite

under a open-source 3-clause BSD license. Update the README
for this.

The discussion shows that it's hard to change the hardware
regarding the default SPI NOR boot of the SabreLite boards.
I.e. this will stay the default boot. Therefore remove the
'early version of' statement.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <liu.h.jason@gmail.com>

i.mx28: Replaced magic numbers for scratch register addresses with register definitions

This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.

Signed-off-by: Robert Delien <robert@delien.nl>

i.mx28: Added register definitions for DIGCTL registers

This patch adds register definitions for the registers of the DIGCTL
IP-block.

Signed-off-by: Robert Delien <robert@delien.nl>

PXA: Fix missing get_tbclk() breaking vpac boards

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

PXA: Fix warning in zipitz2

Configuring for zipitz2 board...
zipitz2.c: In function ‘board_mmc_init’:
zipitz2.c:85:2: warning: implicit declaration of function ‘pxa_mmc_register’ [-Wimplicit-function-declaration]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

arm: Remove jornada link script

This link script seems old and incompatible with relocation and its
own sa1000 start.S file. It isn't used because the CPU's link script
was picked up in preference to this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>

PXA: Remove PXA PCMCIA support

Say good bye to some ancient, very broken and unused code.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

zipitz2: use pxa_mmc_gen as MMC driver

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>

zipitz2: fix boot issue introduced by PXA low level init rework

CONFIG_SYS_INIT_SP_ADDR points to RAM, but it's used before
DRAM controller init. Fix it by setting CONFIG_SYS_INIT_SP_ADDR
to SRAM

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>

Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash

* 'master' of git://git.denx.de/u-boot-cfi-flash:
  cfi: fix the incomplete erased status check in buffer write

Merge branch 'master' of git://git.denx.de/u-boot-nds32

* 'master' of git://git.denx.de/u-boot-nds32:
  nds32/n1213: correct vector table in start.S
  nds32: fix ptrace and interrupt register overflow

Revert "Add board_pre_console_putc to deal with early console output"

This reverts commit 295d3942b806552503243f5cfb36aec6f1b5a9bf.

It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>

cfi: fix the incomplete erased status check in buffer write

Without the fix, flash_write_cfibuffer will terminate the erased
status check once an all-0xFF word has been found instead of
continuing the erased status check utill the first non-0xFF word.

Signed-off-by: Tao Hou <hotforest@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

ETX094: adjust linker script due to grown code size

Recent bootstage commits made the code grow, which caused linker
errors.  Adjust the linker script to fix that.

Signed-off-by: Wolfgang Denk <wd@denx.de>

nds32/n1213: correct vector table in start.S

Correct definition of vector table in start.S

Signed-off-by: Macpaul Lin <macpaul@gmail.com>

nds32: fix ptrace and interrupt register overflow

Fix ptrace and interrupt register overflow warning.
Add missing P0 and P1 (r26 and r27) into register lists.
These register are usually used in OS.

Signed-off-by: Macpaul Lin <macpaul@gmail.com>

Armada100: gplugD: Add FAT & EXT2 command support

This patch adds FAT and ext2 command support for marvell gplugD

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

Armada100: gplugD: Add USB command support

This patch adds support for USB commands and USB storage device for
Marvell gplugD

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

USB: Armada100: EHCI Driver for Armada100 SOCs

This patch adds support for USB EHCI driver for Armada100 SOCs.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

USB: Armada100: Add UTMI PHY interface driver

This patch adds USB host controller's UTMI PHY interface driver for
Armada100 SOCs.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

git-mailrc: change usb maintainer to Marek

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

usb:udc:samsung:fix Remove the req_config flag

The dev->req_config flag was indicating that the forwarded
request needs to perform the usb gadget delayed status.
This is however not needed anymore, so it can be removed.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>

USB:gadget:designware Fix memory nonalignment issue

While receiving packets from FIFO sometimes the buffer provided was
nonaligned. Fix this by taking a temporary aligned buffer and then
copying the content to nonaligned buffer.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>