Config: Add initial config for SMDK5420

Adding initial config for SMDK5420 to build and boot U-Boot
over Exynos based SMDK5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

DTS: Add dts support for SMDK5420

This patch adds dts support for SMDK5420.
exynos5.dtsi created is a common file which has the nodes common
to both 5420 and 5250.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Exynos5420: Add base patch for SMDK5420

Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Exynos5420: Add support for 5420 in pinmux and gpio

Adds code in pinmux and gpio framework to support Exynos5420.

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Exynos5420: Add DDR3 initialization for 5420

This patch intends to add DDR3 initialization code for Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Exynos5420: Add clock initialization for 5420

This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

EXYNOS5420: Add dmc and phy_control register structure

Add dmc and phy_control register structure for 5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

EXYNOS5420: Add power register structure.

Add structure for power register for Exynos5420

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Exynos5420: Add base addresses for 5420

Adds base addresses of various IPs and controllers required for
Exynos5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

EXYNOS5: Create a common board file

Create a common board.c file for all functions which are common across
all EXYNOS5 platforms.

exynos_init function is provided for platform specific code.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

ARM: AM43xx: Add Maintainer

Adding Maintainer for AM43xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: GP_EVM: Add support for DDR3

GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: EPOS_EVM: Add support for LPDDR2

AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM33xx+: Update ioregs to pass different values

Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>

ARM: AM43xx: clocks: Update DPLL details

Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE  VDD_MPU
OPP50 OPP50
OPP50  OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: mux: Update mux data

Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: Update Current Booting devices list

Current Booting devices list is different from that of AM33xx.
Updating the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: Select clk source for Timer2

Selecting the Master osc clk as Timer2 clock source.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43XX: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support

CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and
CONFIG_BOARD_LATE_INIT is already set. Adding support to detect the
board. These variables are used by findfdt.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43XX: board: add support for reading onboard EEPROM

Add support for reading onboard EEPROM to enable
board detection.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: Add extra ENV settings

Add Extra env settings.
This is derived from am335x Extra ENV settings.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: Add L2 Support

AM4372 uses PL310 L2 Cache. Enable the configs for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: Adapt to ti_armv7_common.h config file

Use ti_armv7_common.h config file to inclde the common
configs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: AM43xx: Update the base addresses of modules

PRCM, timer base addresses and offsets are different from
AM33xx. Updating the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: omap3: Fix beagleboard SPL boot hangup (GPIO clocks not enabled)

Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Beagleboard. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>

Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master'

Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'

ARM: pxa: Fix CONFIG_SYS_HZ on PXA

The PXA incorrectly uses CONFIG_SYS_HZ, which should be 1000 across
U-Boot. Fix this.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

arm: tegra: Fix the CPU complex reset masks

The CPU complex reset masks are not matching with the datasheet for
the CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET/CLR_0 registers. For both T20
and T30 the register consist of groups of 4 bits, with one bit for
each CPU core. On T20 the 2 high bits of each group are always stubbed
as there is only 2 cores.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swrren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board

Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

i2c: tegra: Add the fifth bus on SoC with more than 4 buses

Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>

ARM: tegra: support SKU b1 of Tegra30

Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>

ARM: config: USB: Tegra30/114: Fix EHCI timeout issue on "bootp"

Fix the timeout issue after running "bootp" command in u-boot
console. For example you see "EHCI timed out on TD- token=0x...".
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10
after a controller reset and before RUN bit is set
(per technical reference manual).

Signed-off-by: Jim Lin <jilin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

tegra: allow build to succeed with SPL disabled

u-boot-dtb-tegra.bin and u-boot-nodtb-tegra.bin binaries
are generated only if the SPL build is enabled as they have
dependency on SPL build

Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Change maintainer for Avionic Design boards

I no longer work for Avionic Design and don't have access to hardware,
so I'll pass on maintainership to Alban.

Acked-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Tegra114: Do not program CPCON field for PLLX

PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Tegra114: Fix PLLX M, N, P init settings

The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordingly.

Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Reviewed-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

arm: pxa: init ethaddr for LP-8x4x using DT

When DT define aliases for etherner0 and ethernet1, U-Boot
automatically patched MAC addresses using ethaddr and eth1addr
environment variables respectively.

Custom initialization is no longer needed.

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

arm: pxa: update LP-8x4x to boot DT kernel

DT kernel requires CONFIG_OF_LIBFDT. 'bootm' needs to know DT location.
In addition, fix kernel console device and enable U-Boot long help.

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

arm: pxa: fix 2nd flash chip address on LP-8x4x

Initial configuration has worng address of the second chip.
There is an alias for the 1st chip at 0x02000000 in earlier
verions of LP-8x4x, so the boot normally.

However, new LP-8x4xs have a bigger 1st flash chip, and hang on
boot without this patch.

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

arm: pxa: fix LP-8x4x USB support

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'

ARM: pxa: prevent PXA270 occasional reboot freezes

Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.

If SDRAM is not reset, it causes memory bus congestion and
the device hangs.

We put SDRAM in selfresh mode before watchdog reset, removing
potential freezes.

Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

arm: koelsch: Add support reset function

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

arm: koelsch: Add support I2C

This supports sh_i2c on koelsch board.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

arm: koelsch: Add support Ethernet

The koelsch board has one sh-ether device.
This supports sh-ether.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: lager: Add support reset function

The lager board uses I2C for reset.

ned-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

arm: lager: Add support I2C

The lager board has I2C for rcar.
This supports I2C for rcar on lager board.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

arm: lager: Add support Ethernet

The lager board has one sh-ether device.
This supports sh-ether.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

arm: rmobile: Update README.rmobile

Add infomation of Lager and Koelsh board, and R-Car.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: atmel: at91sam9x5: move CONFIG_SYS_NO_FLASH to proper position

In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: atmel: at91sam9x5: cleanup unneeded undef

remove unneeded #undef for at91sam9x5ek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm: atmel: at91sam9x5: cleanup cs configure for spi

As the cs for spi is worked in gpio mode, so no need to configure
it as peripheral and then configure to gpio. Configure it to gpio
directly.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: OMAP5: clocks: Update MPU settings for OPP_NOM

As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MHz. Fixing the same and cleaning the
previously used dpll values.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: DRA7xx: Change clk divider setting

Commit "armv7: hw_data: change clock divider setting"
updates the setting for m6 divider for 20MHz sys_clk frequency.
But missed to update for other sys_clk frequencies. Doing the same.

Reported-by: Rajendran, Vinothkumar <vinothr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: omap: cm_t35: update config file

This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
  notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
  sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
  "ULPI: ulpi_reset: failed writing reset bit"
  So, remove it.

Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>

am3517_evm: activate Ethernet PHY

Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

am335x, siemens boards: adapt default environment setting

commit 16297cfb2a20c9d89834cd9e31edac5184a777a1
Author: Mateusz Zalega <m.zalega@samsung.com>
Date:   Fri Oct 4 19:22:26 2013 +0200

    usb: new board-specific USB init interface

introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>

arm: omap: abb: add missing include

ABB code uses LDELAY but does not include the header that provides its
definition.

Include the header.

Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nishanth Menon <nm@ti.com>

arm: am437: Fix offset for USB registers

Fix the offset for the USB clock registers

Signed-off-by: Dan Murphy <dmurphy@ti.com>

am335x_evm: Consolidate DFU environment parts into the DFU part of the file

To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS.  Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.

Signed-off-by: Tom Rini <trini@ti.com>

arm: omap3: Add SPL support to cm_t35

Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.

Tested by booting via MMC and NAND.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

arm: omap3: Add HEAD acoustics (HA) board variant omap3_ha to tao3530

The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

arm: omap3: Add board revision output to tao3530

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

arm: omap3: Remove bootargs mem_size handling

The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

arm: omap3: Add SPL support to tao3530

Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).

Tested by booting via MMC and NAND.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

arm, omap3: Add support for TechNexion modules

Add support for TechNexion TAO3530 SoM

This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.

Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

ARM: OMAP4: Move TEXT_BASE down to non-HS limit

With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html

Tested on OMAP4460 PANDA.

Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

am33xx: Enable D-CACHE on !CONFIG_SYS_DCACHE_OFF

Test on Beaglebone white over cpsw, usb ether and SD card (read and
write), performance increased, crc32 of data matches.

Signed-off-by: Tom Rini <trini@ti.com>

ARM: fix the standalone programs

The standalone programs do not use the api calls, but rely
directly on u-boot variable gd->jt for the jump table. Commit
fe1378a - "ARM: use r9 for gd" changed the register holding
the address of gd, but the assembly code in the standalone
examples was not updated accordingly. This broke the programs
on ARM relying on the jumptable in the v2013.10 release.
This patch unbricks them by using the correct register.

Cc: Michal Simek <monstr@monstr.eu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>

Revert "ARM: move interrupt_init to before relocation"

Revert commit 0f5141e9 which causes boards starting in
FLASH to try and write to a FLASH location.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
board/samsung/trats2/trats2.c
include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard

Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds

Merge branch 'spi' of git://git.denx.de/u-boot-x86

Merge branch 'master' of git://git.denx.de/u-boot-mmc

Merge branch 'master' of git://git.denx.de/u-boot-i2c

vexpress: use correct timer address on extended memory map systems

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: albert.u.boot@aribaud.net

serial: zynq: Remove unused #defines

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

sandbox: spi: Enable new spi/sf layers

We want to test SPI flash code in the sandbox, so enable the new drivers and
the 'sf test' command.

This command is used to validate the sandbox SPI / SPI flash implementation,
so enable it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

sandbox: spi: Add new SPI flash driver

This adds a SPI flash driver which simulates SPI flash clients.
Currently supports the bare min that U-Boot requires: you can
probe, read, erase, and write.  Should be easy to extend to make
it behave more exactly like a real SPI flash, but this is good
enough to merge now.

sjg@chromium.org added a README and tidied up code a little.
Added a required map_sysmem() for sandbox.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

sandbox: spi: Add SPI emulation bus

This adds a SPI framework for people to hook up simulated SPI clients.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

spi: Add device tree binding for SPI bus

This was obtained from Linux 3.12 commit 5e01dc7b26.

Signed-off-by: Simon Glass <sjg@chromium.org>

spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT node

This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.

Signed-off-by: Simon Glass <sjg@chromium.org>

sandbox: Rename sb_cmdline_option to sandbox_cmdline_option

The new name is longer but more clearly related to sandbox.

This is in a separate patch within the same series since some comments on the
SPI series rely on it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>

arm: at91: support for the Calao USB-A9263 board (based on AT91SAM9263)

Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm, at91: add siemens corvus board

enable support for the siemens AT91SAM9G20 based board corvus.

Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

arm, at91: add Siemens board taurus and axm

enable support for the siemens AT91SAM9G20 based boards taurus
and axm.

Signed-off-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91: switch coloured LED to gpio API

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91: nand: switch atmel_nand to generic GPIO API

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Acked-by: Scott Wood <scottwood@freescale.com>

at91: redefine legacy GPIO PIN_BASE

In order to get the very same value for legacy pin definitions and new gpio
definitions set the legacy PIN_BASE to 0.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91: add new gpio pin definitions

This patch define new names for GPIO pins on at91 devices. Follow up patches
will convert the whole infrastructure to use these new definitions.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Bo Shen <voice.shen@atmel.com>

mmc: add Faraday FTSDC021 SDHCI controller support

Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.

However this driver is only verified with SD memory cards.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>

powerpc: mmc: Add corenet devices support in esdhc spl

Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.

So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

mmc/dwmmc: modify FIFO threshold only if value explicitly set

If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.

This implementation allows:
 * escape unclear and recursive calculations that are currently in use
 * use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

mmc: dw_mmc: remove the exynos specific code in dw-mmc.c

dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>

arm: keep all sections in ELF file

Current LDS files /DISCARD/ a lot of sections when linking ELF
files, causing diagnostic tools such as readelf or objdump to
produce partial output. Keep all section at link stage, filter
only at objcopy time so that .bin remains minimal.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

ARM: align MVBAR on 32 byte boundary

The lower 5 bit of MVBAR is UNK/SBZP.
So, Monitor Vector Base Address must be 32-byte aligned.
On the other hand, the secure monitor handler does not need
32-byte alignment.

This commit moves ".algin 5" directive to the correct place.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andre Przywara <andre.przywara@linaro.org>
Acked-by: Andre Przywara <andre.przywara@linaro.org>

Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-blackfin