Sam Shih [Fri, 10 Jan 2020 08:30:29 +0000 (16:30 +0800)]
clk: mediatek: add driver for MT7622
This patch add clock driver for MediaTek MT7622 SoC.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Sam Shih [Fri, 10 Jan 2020 08:30:28 +0000 (16:30 +0800)]
pinctrl: mediatek: add support for different pinctrl
Due to the pinctrl hardware of MT7622 is difference from others
SoC which using the common part of mediatek pinctrl.
So we need to modify the common part of mediatek pinctrl.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Sam Shih [Fri, 10 Jan 2020 08:30:27 +0000 (16:30 +0800)]
pinctrl: mediatek: add driver for MT7622
This patch add Pinctrl driver for MediaTek MT7622 SoC.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Sam Shih [Fri, 10 Jan 2020 08:30:26 +0000 (16:30 +0800)]
ARM: MediaTek: Add support for MediaTek MT7622 SoC
Add support for MediaTek MT7622 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:10 +0000 (11:35 +0800)]
phy: phy-mtk-tphy: make ref clock optional
If make the ref clock optional, no need refer to fixed-clock when
the ref clock is always on or comes from oscillator directly.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:09 +0000 (11:35 +0800)]
phy: phy-mtk-tphy: remove the check of -ENOSYS
No need check -ENOSYS anymore after add dummy_enable() for
fixed-clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:08 +0000 (11:35 +0800)]
clk: fixed_rate: add dummy enable() function
This is used to avoid clk_enable() return -ENOSYS.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:07 +0000 (11:35 +0800)]
clk: add APIs to get (optional) clock by name without a device
Sometimes we may need get (optional) clock without a device,
that means use ofnode.
e.g. when the phy node has subnode, and there is no device created
for subnode, in this case, we need these new APIs to get subnode's
clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:06 +0000 (11:35 +0800)]
clk: check valid clock by clk_valid()
Add valid check for clk->dev, it's useful when get optional
clock even when the clk point is valid, but its dev will be
NULL.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:05 +0000 (11:35 +0800)]
clk: fix error check for devm_clk_get_optional()
If skip all return error number, it may skip some real error cases,
so only skip the error when the clock is not provided in DTS
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Chunfeng Yun [Thu, 9 Jan 2020 03:35:04 +0000 (11:35 +0800)]
clk: mediatek: mt7629: add support for ssusbsys
The SSUSB IP's clocks come from ssusbsys module on mt7629,
so add its driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
mingming lee [Tue, 31 Dec 2019 03:29:26 +0000 (11:29 +0800)]
ARM: MediaTek: add basic support for MT8512 boards
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
mingming lee [Tue, 31 Dec 2019 03:29:25 +0000 (11:29 +0800)]
mmc: mtk-sd: fix hang when data read quickly
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
mingming lee [Tue, 31 Dec 2019 03:29:24 +0000 (11:29 +0800)]
mmc: mtk-sd: add support for MediaTek MT8512/MT8110 SoCs
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
mingming lee [Tue, 31 Dec 2019 03:29:23 +0000 (11:29 +0800)]
pinctrl: mediatek: add driver for MT8512
Add Pinctrl driver for MediaTek MT8512 SoC.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
mingming lee [Tue, 31 Dec 2019 03:29:22 +0000 (11:29 +0800)]
clk: mediatek: add configurable pcw_chg_reg/ibits/fmin to mtk_pll
Add configurable pcw_chg_reg/ibits/fmin to mtk_pll to support mt8512
mingming lee [Tue, 31 Dec 2019 03:29:21 +0000 (11:29 +0800)]
clk: mediatek: add set_clr_upd mux type flow
Add new set_clr_upd mux type and related operation to
mtk common clock driver to support mt8512
mingming lee [Tue, 31 Dec 2019 03:29:20 +0000 (11:29 +0800)]
clk: mediatek: add driver support for MT8512
Add clock driver for MediaTek MT8512 SoC, include topckgen,
apmixedsys and infracfg support.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
mingming lee [Tue, 31 Dec 2019 03:29:19 +0000 (11:29 +0800)]
ARM: MediaTek: Add support for MediaTek MT8512 SoC
Add support for MediaTek MT8512 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Sam Protsenko [Tue, 14 Jan 2020 17:54:12 +0000 (19:54 +0200)]
MAINTAINERS: Fix mail
Sam doesn't work for Linaro anymore, so Linaro mail is not valid. Change
it to his home mail instead.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Alexandre Besnard [Fri, 20 Dec 2019 14:25:22 +0000 (15:25 +0100)]
cmd/blk_common: clarify no partition error message
When no partition table is found, users should be warned so.
Warning that no device is available in this case could be misleading,
especially as it is the same error when no device is selected.
Signed-off-by: Alexandre Besnard <alexandre.besnard@softathome.com>
Heinrich Schuchardt [Wed, 18 Dec 2019 10:05:59 +0000 (11:05 +0100)]
test/py: use valid device tree in test_fit.py
The device tree compiler expects that a node with a unit-address has a reg
property.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Wed, 18 Dec 2019 02:40:09 +0000 (21:40 -0500)]
Add dependencies for MALLOC_F and OF_LIBFDT
Some features implicitly depended on MALLOC_F and OF_LIBFDT and would
fail at link-time if these features were not enabled.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Sean Anderson [Wed, 18 Dec 2019 02:22:42 +0000 (21:22 -0500)]
Include missing headers for asm-generic/sections.h
asm-generic/sections.h references ulong but does not include
linux/types.h
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Vignesh Raghavendra [Fri, 15 Nov 2019 11:30:42 +0000 (17:00 +0530)]
dma: Add stub of dma_memcpy and dma_get_device
Add stub for dma_memcpy() and dma_get_device when CONFIG_DMA is
disabled. This avoids ifdefs in driver code using DMA APIs
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vignesh Raghavendra [Fri, 15 Nov 2019 11:30:41 +0000 (17:00 +0530)]
Kconfig: Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 15 Jan 2020 17:29:23 +0000 (12:29 -0500)]
Merge tag 'efi-2020-04-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1-2
Bug fixes for the UEFI sub-system are provided:
* imply VIDEO_ANSI for correct cursor positioning and colors
* fix issues in the UEFI block device driver
* add missing documentation
Tom Rini [Wed, 15 Jan 2020 14:22:15 +0000 (09:22 -0500)]
Merge tag 'u-boot-imx-
20200115' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
-----------------------------------
- imx8:
add capricorn giedi deneb boards
- imx6:
fixed fow wandboard
- imx7: DM_ETHER for pico-imx7d
- fsl_esdhc_imx: add broken-cd property
- New SOC: IMXRT10xx
Travis:
https://travis-ci.org/sbabic/u-boot-imx/builds/
637126531
Tom Rini [Wed, 15 Jan 2020 02:48:32 +0000 (21:48 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-tegra
- Important bugfix for some Tegra platforms
Heinrich Schuchardt [Tue, 14 Jan 2020 23:49:35 +0000 (00:49 +0100)]
efi_loader: imply VIDEO_ANSI
UEFI programs like GRUB make change terminal colors which requires support
for ANSI escape sequences.
Let CONFIG_EFI_LOADER=y imply CONFIG_VIDEO_ANSI.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 10 Jan 2020 11:33:16 +0000 (12:33 +0100)]
efi_driver: debug output efi_uc_start, efi_uc_stop
Use the correct printf codes for the debug output in efi_uc_start() and
efi_uc_stop().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Thu, 9 Jan 2020 22:26:43 +0000 (23:26 +0100)]
efi_driver: fix efi_uc_stop()
Use the correct protocol in efi_uc_stop() when detaching the driver from
the controller.
Change the block IO unit test for the block device driver to throw an error
instead of a todo if teardown fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 11 Jan 2020 09:59:08 +0000 (10:59 +0100)]
efi_selftest: enable CONFIG_CMD_POWEROFF
For automating testing we should be able to power off the test system.
The implementation of EFI_RESET_SHUTDOWN requires the do_poweroff()
function which is only available if CONFIG_CMD_POWEROFF=y.
Enable CONFIG_CMD_POWEROFF if PSCI reset is available.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 10 Jan 2020 21:06:54 +0000 (22:06 +0100)]
efi_loader: describe returning of control
Provide a sober description of how control can be returned by a UEFI
binary.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Thu, 9 Jan 2020 19:49:44 +0000 (20:49 +0100)]
efi_loader: document functions in efi_rng.c
Add the missing Sphinx documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:51:48 +0000 (15:51 +0100)]
imx: imxrt1050-evk: Add support for the NXP i.MXRT1050-EVK
This commit adds board support for i.MXRT1050-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT105x processor family.
More information about this board can be found here:
https://www.nxp.com/design/development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1050-evaluation-kit:MIMXRT1050-EVK
The initial supported/tested devices include:
- Debug serial
- SD
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:51:47 +0000 (15:51 +0100)]
imx: Add basic support for the NXP IMXRT10xx SoC family
Add i.IMXRT family basic support.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:51:46 +0000 (15:51 +0100)]
mmc: fsl_esdhc: add compatible for fsl, imxrt-usdhc
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:51:45 +0000 (15:51 +0100)]
mmc: fsl_esdhc: make if(CONFIG_IS_ENABLED(CLK)) an #if statement
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK
instead. So building could result in failure due to missing
mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:51:44 +0000 (15:51 +0100)]
ram: add SDRAM driver for i.MXRT SoCs
Add SDRAM driver for i.MXRT SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:51:43 +0000 (15:51 +0100)]
serial_lpuart: add support for i.MXRT
Add i.MXRT compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08 as done
for i.MX8. It needs also to set baudrate the same way as i.MX8 does.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:47:05 +0000 (15:47 +0100)]
serial_lpuart: add clock enable if CONFIG_CLK is defined
This driver assumes that lpuart clock is already enabled before probing
but using DM only lpuart won't be automatically enabled so add
clk_enable() when probing if CONFIG_CLK is defined. If clock is not
found, because DM is not used, let's emit a warning and proceed, because
serial clock could also be already enabled by non DM code. If clock is
found but cna't be enabled then return with error.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:47:04 +0000 (15:47 +0100)]
ARM: dts: imxrt1050: add dtsi file
Add dtsi file for i.MXRT1050.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:47:03 +0000 (15:47 +0100)]
gpio: mxc_gpio: add support for i.MXRT1050
Add i.MXRT1050 support, there are 5 GPIO banks.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:47:02 +0000 (15:47 +0100)]
pinctrl: add i.MXRT driver
Add i.MXRT pinctrl driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:47:01 +0000 (15:47 +0100)]
clk: imx: add i.IMXRT1050 clk driver
Add i.MXRT1050 clk driver support.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:47:00 +0000 (15:47 +0100)]
clk: imx: pfd: add set_rate()
Implement set_rate() for pfd.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:46:59 +0000 (15:46 +0100)]
clk: imx: pllv3: add support for PLLV3_AV type
Add support for PLLV3 AV type.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:46:58 +0000 (15:46 +0100)]
clk: imx: pllv3: add PLLV3_SYS support
Add PLLV3_SYS support by adding set/get_rate() for PLLV3_SYS but keeping
generic enable()/disable(). Add a different driver because ops are
different respect to GENERIC/USB.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:46:57 +0000 (15:46 +0100)]
clk: imx: pllv3: add set_rate() support
Add generic set_rate() support.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:46:56 +0000 (15:46 +0100)]
clk: imx: pllv3: add disable() support
Add disable() support.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:46:55 +0000 (15:46 +0100)]
clk: imx: pllv3: add enable() support
Before set_rate() pllv3 needs enable() to power the pll up.
Add enable() taking into account different power_bit and
different powerup_set, because some pll needs its power_bit to be
set or reset to be powered on.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:46:54 +0000 (15:46 +0100)]
clk: imx: pllv3: set div_mask differently if PLLV3 is GENERIC or USB
div_mask is different for GENERIC and USB pll, so set it according.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:46:53 +0000 (15:46 +0100)]
clk: imx: pllv3: register PLLV3 GENERIC and USB as 2 different clocks
Better to register the 2 clock as 2 different drivers because they work
slightly differently depending on power_bit and powerup_set bits coming
on next patches.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Giulio Benetti [Fri, 10 Jan 2020 14:46:52 +0000 (15:46 +0100)]
armv7m: cache: add mmu_set_region_dcache_behaviour() stub for compatibility
Since some driver requires this function add it as an empty stub
when DCACHE is OFF.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Giulio Benetti [Fri, 10 Jan 2020 14:46:51 +0000 (15:46 +0100)]
spl: fix entry_point equal to load_addr
At the moment entry_point is set to image_get_load(header) that sets it
to "load address" instead of "entry point", assuming entry_point is
equal to load_addr, but it's not true. Then load_addr is set to
"entry_point - header_size", but this is wrong too since load_addr is
not an entry point.
So use image_get_ep() for entry_point assignment and image_get_load()
for load_addr assignment.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Anatolij Gustschin [Tue, 7 Jan 2020 13:03:04 +0000 (14:03 +0100)]
imx: dts: imx8dx: add I2C IPG clock for bus 0 and 2
IPG clock description is missing for I2C0 and I2C2 busses,
add it. Otherwise we see -ENODATA error when trying to get
I2C clock for these busses.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Anatolij Gustschin [Tue, 7 Jan 2020 13:03:03 +0000 (14:03 +0100)]
clk: imx8qxp: extend to support getting I2C IPG clock
Since commit
d02be21d3004 ("i2c: imx_lpi2c: add ipg clk") getting
I2C clocks doesn't work. Add I2C IPG clock IDs to related switch
statements to fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Mon, 6 Jan 2020 23:11:28 +0000 (20:11 -0300)]
ARM: dts: imx6ul-14x14-evk: Pass the "broken-cd" property
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 port. In such cases the "broken-cd" property
must be passed, otherwise the card cannot be detected.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Mon, 6 Jan 2020 23:11:27 +0000 (20:11 -0300)]
mmc: fsl_esdhc_imx: Handle the "broken-cd" property
When no GPIO is used to read the card detect status the following
error is seen:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by handling the "broken-cd" property in the same way
that drivers/mmc/sdhci.c does, which considers that the SD card
is present when the "broken-cd" property is passed.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Joris Offouga [Sun, 5 Jan 2020 23:22:09 +0000 (00:22 +0100)]
pico-imx7d: Convert to DM_ETH
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Joris Offouga [Sun, 5 Jan 2020 23:22:08 +0000 (00:22 +0100)]
pico-imx7d: Disable USB_ETHER support for bl33 defconfig
For DM_ETH support , it's require to disable this config.
When this config is enable, This generate a error with spl in linker script
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Mon, 6 Jan 2020 15:31:55 +0000 (12:31 -0300)]
mx6ul_14x14_evk: Fix SPL boot hang
Currently the following SPL hang is observed:
U-Boot SPL
2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300)
Trying to boot from MMC1
Card did not respond to voltage select!
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix it by moving the eSDHC2 initialization to SPL.
While at it, since this board uses DM_MMC all the esdhc board
code can be removed to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Wed, 8 Jan 2020 01:33:31 +0000 (01:33 +0000)]
imx: imx8qxp_mek: update README
Update README to use 4.19.35_1.1.0 released firmware images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Thu, 9 Jan 2020 01:05:05 +0000 (22:05 -0300)]
wandboard: Do not print error message when PMIC is absent
Only the wandboard revD1 boards have PMIC, so when running on a wandboard
of different revision the following error is always shown on every boot:
pmic_get() ret -19
Instead of printing this error message, move it to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 9 Jan 2020 14:07:23 +0000 (11:07 -0300)]
imx8qxp_mek: Select CONFIG_NET_RANDOM_ETHADDR
Some i.MX8QXP MEK boards do not have MAC address stored
and hang during eth driver probe:
Error: ethernet@
5b040000 address not set.
(Board hangs)
To fix this problem select CONFIG_NET_RANDOM_ETHADDR so that
a valid MAC address can be used in such case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Anatolij Gustschin [Tue, 7 Jan 2020 15:37:43 +0000 (16:37 +0100)]
imx: add imx8x based deneb board
Add support for Capricorn Deneb SoM variant.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Tue, 7 Jan 2020 15:37:42 +0000 (16:37 +0100)]
imx: add imx8x capricorn giedi board
Add support for i.MX8X based Capricorn Giedi SoM.
Supported interfaces: GPIO, ENET, eMMC, I2C, UART.
Console output:
U-Boot SPL
2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100)
Trying to boot from MMC1
Load image from MMC/SD 0x3e400
U-Boot
2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
Model: Siemens Giedi
Board: Capricorn
Boot: MMC0
DRAM: 1022 MiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
In: serial@
5a080000
Out: serial@
5a080000
Err: serial@
5a080000
Net: eth1: ethernet@
5b050000 [PRIME]
Autobooting in 1 seconds, press "<Esc><Esc>" to stop
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Stephen Warren [Tue, 7 Jan 2020 18:17:54 +0000 (11:17 -0700)]
tegra: fdt: Add tegra186-u-boot.dtsi
All Tegra chips except Tegra186 have a tegraNNN-u-boot.dtsi. Duplicate
Tegra210's copy of this file for Tegra186. This ensures that a /binman node
exists in U-Boot's control DT. Subsequent to
3c10dc95bdd0 ("binman: Add a
library to access binman entries") this appears to be required. I haven't
really investigated why all this is necessary or how it works, but simply
observed the boot failure listed below, bisected it, noticed the
inconsistency in DT files, and found that fixing it resolved the boot
issue.
U-Boot
2020.01-rc4-00256-g3c10dc95bdd0 (Jan 07 2020 - 10:25:00 -0700)
SoC: tegra186
Model: NVIDIA P2771-0000-500
Board: NVIDIA P2771-0000
DRAM: 7.8 GiB
initcall sequence
00000000fffb7858 failed at call
00000000800955a8 (err=-22)
### ERROR ### Please RESET the board ###
Fixes:
3c10dc95bdd0 ("binman: Add a library to access binman entries")
Fixes:
f2faffecb016 ("binman: tegra: Convert to use binman")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 11 Jan 2020 13:07:03 +0000 (08:07 -0500)]
travis: Switch to QEMU v4.2.0 globally
Given our tests in GitLab / Azure we can use QEMU v4.2.0 for all
platforms now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 10 Jan 2020 22:07:27 +0000 (17:07 -0500)]
gitlab/azure: Update to latest container
- Updated base snapshot
- QEMU v4.2.0
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 10 Jan 2020 21:38:40 +0000 (16:38 -0500)]
Merge branch '2020-01-10-master-imports'
- Android image support enhancements
- Assorted ARM fixes and enhancements
- m68k update
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:08 +0000 (17:51 +0100)]
cmd: adtimg: Refactor usage style
Trying to extend 'adtimg' functionality [1], we've been severely hit
by a major limitation in the command's usage scheme. Specifically, the
command's user interface appears to be too centric to getting the
DTB/DTBO entry [3] based on the index of the desired DT in the image,
which makes it really difficult retrieving the DT entry based on
alternative criteria (e.g. filtering by id/rev fields), the
latter being demanded by real life customer use-cases [1].
This went to the point of receiving below feedback from Sam [2]:
-- snip --
As for 'dtimg' command: after giving it some thought, I think not much
people using it yet. So in this particular case I don't have some
strong preference, and if you think the 'dtimg' interface is ugly, and
it overcomes "don't break interfaces" rule, maybe now is a good time
to rework it (before it gets widely used).
-- snip --
Given the above, rework the usage pattern from [4] to [5], in order to
allow an intuitive enablement of "by id|rev" DT search [6].
[1] https://patchwork.ozlabs.org/cover/
1202575/
("cmd: dtimg: Enhance with --id and --rev options (take #1)")
[2] https://patchwork.ozlabs.org/patch/
1182207/#
2317020
[3] https://source.android.com/devices/architecture/dto/partitions
[4] Old usage
adtimg dump <addr> - Print image contents
adtimg start <addr> <index> <varname> - Get DT address by index
adtimg size <addr> <index> <varname> - Get DT size by index
[5] New usage
adtimg addr <addr> - Set image location to <addr>
adtimg dump - Print out image contents
adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index
[6] Soon-to-be-provided "by id|rev" add-on functionality
adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]]
- Get DT address/size/index by id|rev fields
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:07 +0000 (17:51 +0100)]
cmd: adtimg: Rename internal symbols
With 'dtimg.c' renamed to 'adtimg.c', now ensure the naming
consistency in the internal implementation of 'adtimg.c'.
No functional change intended.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:06 +0000 (17:51 +0100)]
dtimg/am57xx_evm_defconfig: Rename dtimg to adtimg
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
[*] https://patchwork.ozlabs.org/patch/
1182212/#
2291600
[**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o)
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass<sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Heinrich Schuchardt [Tue, 24 Dec 2019 11:21:09 +0000 (12:21 +0100)]
virtio: fix typo devicd
%s/devicd/device
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rajesh Ravi [Fri, 22 Nov 2019 22:50:01 +0000 (14:50 -0800)]
arm: cpu: armv8: add support for arm psci reset2.
Current U-Boot has only support for psci reset.
Adding support for arm psci reset2 allows passing of reset level
and other platform sepcific parameters like strap settings
to lowlevel psci implementation.
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Bharat Kumar Reddy Gooty [Mon, 16 Dec 2019 17:09:43 +0000 (09:09 -0800)]
arch: arm: Program GIC LPI configuration table
Programs the following:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Heinrich Schuchardt [Wed, 11 Dec 2019 12:51:38 +0000 (13:51 +0100)]
mkimage: simplify fit_check_params()
fit_check_params() wants at least two of dflag, fflag, and lflag set.
Simplify the logical constraint checking this.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Klaus H. Sorensen [Wed, 11 Dec 2019 11:18:29 +0000 (11:18 +0000)]
cmd/eeprom.c: prepend 0x to hex numbers in output message format
If the numbers do not happen to contain any digits from [a-f], it's
not clear that they are base 16.
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Philippe Reynes [Thu, 9 Jan 2020 16:34:02 +0000 (17:34 +0100)]
test/cmd_ut.c: fix cmd_ut_category
In the function cmd_ut_category, the prefix is used with
the function strncmp to know if the prefix should be
removed from the test name, even if the prefix is NULL.
To avoid this issue, we consider that a prefix NULL
mean no prefix. So we only try to remove the prefix
from the test_name if the prefix is not NULL, then
we avoid to call the function strncmp with a NULL
prefix.
Reported-by: Coverity CID 281110
Fixes:
4ad4edfe ("cmd_ut: add a parameter prefix to the function cmd_ut_category")
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Andy Shevchenko [Fri, 29 Nov 2019 17:47:59 +0000 (19:47 +0200)]
gcc-9: silence 'address-of-packed-member' warning
GCC 9.x starts complaining about potential misalignment of the pointer to
the array (in this case alignment=2) in the packed (alignment=1) structures.
Repeating Linus' Torvalds commit
6f303d60534c in the Linux kernel.
Original commit message:
We already did this for clang, but now gcc has that warning too.
Yes, yes, the address may be unaligned. And that's kind of the point.
This in particular hides the warnings like
drivers/usb/gadget/composite.c:545:23: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
545 | collect_langs(sp, s->wData);
drivers/usb/gadget/composite.c:550:24: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
550 | collect_langs(sp, s->wData);
drivers/usb/gadget/composite.c:555:25: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
555 | collect_langs(sp, s->wData);
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Holger Brunck [Mon, 25 Nov 2019 16:24:16 +0000 (17:24 +0100)]
boards/km_arm: enable support for Macronix SPI NOR flash
The M25P80 and M25P32 SPI flashes from Numonix/Micron
will be replaced by Marconix MX25L80 and MX25L32 flashes.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Holger Brunck [Mon, 25 Nov 2019 16:24:15 +0000 (17:24 +0100)]
arm/km: remove board KMCOGE3UN
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Holger Brunck [Mon, 25 Nov 2019 16:24:14 +0000 (17:24 +0100)]
km/boards: add MAC address offset as argument to ivm_populate_env
For upcoming SECU board we have different MAC address offsets depending
on which functional unit we are running. In this case we need to pass
this value to the ivm_populate_env function instead of using the hard
coded config option there.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Holger Brunck [Mon, 25 Nov 2019 16:24:13 +0000 (17:24 +0100)]
km/boards: fix typo for MAC address offset config option
This patch only fixes a typo.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Frank Wunderlich [Fri, 22 Nov 2019 14:32:24 +0000 (15:32 +0100)]
poweroff: add poweroff for mt6323 pmic
this adds poweroff to bananapi r2 / mt7623 / mt6323 pmic
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Han Nandor [Tue, 12 Nov 2019 08:39:38 +0000 (08:39 +0000)]
rtc: add support for DS3232 device
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM.
Add an RTC driver for DS3232 device, which provides time and
date support. Also read and write functions are provided,
which can be used to access the SRAM memory.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Simon Goldschmidt [Mon, 11 Nov 2019 21:30:46 +0000 (22:30 +0100)]
spl: fix stack usage check if gd is not initialized
Most platforms do not set up gd->start_addr_sp in SPL. Since this is
required for CONFIG_SPL_SYS_REPORT_SACK_F_USAGE to work correctly, set
up gd->start_addr_sp in SPL to the value passed to
board_init_f_init_reserve if it is not set yet.
Fixes:
d8c0332031 ("spl: implement stack usage check")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Mon, 11 Nov 2019 14:39:11 +0000 (09:39 -0500)]
m68k: Drop CONFIG_MCFPIT support
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Robert Beckett [Mon, 28 Oct 2019 18:44:06 +0000 (18:44 +0000)]
bootcount: add a DM i2c eeprom backing store for bootcount
This driver allows the use of i2c eeprom device or partition as backing
store for boot counter values with DM enabled.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:20 +0000 (23:54 +0100)]
drivers: mcfmii: add dm support
Add specific dm code, but maintaining this driver as is, so more in the
shape of a mii library. Can be moved to dm in a further step.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:19 +0000 (23:54 +0100)]
drivers: fsl_mcdmafec: conversion to dm
Full conversion to dm for all boards, legacy code removed.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:18 +0000 (23:54 +0100)]
drivers: mcffec: conversion to dm
Full conversion to dm for all boards, legacy code removed.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:17 +0000 (23:54 +0100)]
drivers: net: add mcf fec dm Kconfig support
Add ColdFire fec to Kconfig.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:16 +0000 (23:54 +0100)]
m68k: add dm fec support
Add architecture-related code for dm fec support.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:15 +0000 (23:54 +0100)]
configs: purge unneeded fec defines
Remove unneeded fec-related defines after fec moved as dm.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:14 +0000 (23:54 +0100)]
configs: add eth dm support for all ColdFire boards
Add dm eth config options for all involved ColdFire-based boards.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:13 +0000 (23:54 +0100)]
m68k: add fec fdt overrides to all boards
Add ethernet controller overrides for all involved boards.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Durgehello [Fri, 15 Nov 2019 22:54:12 +0000 (23:54 +0100)]
m68k: add fec base node to devicetrees
Add basic ethernet controller devicetree nodes for all ColdFire
families.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>