Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (145 commits)
  beagleboard: enable HUB power on all variants of the BeagleBoard
  dm3730: enable dpll5
  ehci-hcd: Allow cleanups to happen gracefully on a timeout.
  OMAP3: Add DSS driver for OMAP3
  led: Remove state-saving of led for toggle functionality and add toggle option to led command
  led: Fixed setting of STATUS_LED_BIT1 when led_name is 'all'
  led: correct off/on locations in structure
  led: added cmd_led to Makefile
  BeagleBoard: fix LED 0/1 in driver
  Corrected LED name match finding avoiding extraneous Usage printouts
  BeagleBoard: config: updated default configuration
  BeagleBoard: config: Enabled multibus support for I2C in configuration
  BeagleBoard: config: add optargs/buddy/camera
  BeagleBoard: config: increase command-line functionality
  BeagleBoard: config: make mtest run
  BeagleBoard: config: enable DSS
  BeagleBoard: config: enable asix driver and dhcp
  BeagleBoard: config: enable networking
  BeagleBoard: config: decrease bootdelay to 2 seconds
  BeagleBoard: config: use uImage.beagle for tftp
  BeagleBoard: config: hardcode MAC for onboard SMSC
  BeagleBoard: config: load kernel from MMC ext, not FAT
  BeagleBoard: Configure DVI/S-video
  BeagleBoard: Added userbutton command
  BeagleBoard: turn off clocks in ehci_stop
  USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor
  beagleboard: add support for xM revision C
  beagle: pass expansionboard name in bootargs
  OMAP: Remove omapfb.debug=y from Beagle and Overo env settings
  OMAP3 Beagle Pin Mux initialization glitch fix
  da850: modifications for Logic PD Rev.3 AM18xx EVM
  da850: fix the channel number for EMAC teardown init
  da850: add support for Spectrum Digital AM18xx EVM
  da850: add support to wake up DSP during board init
  da850: modify the U-Boot prompt string
  da850: add NOR boot mode support
  da8xx: add support for multiple PLL controllers
  da850: indicate cache usage disable in config file
  dm365: modify boot prompt from dm365 to dm36x
  dm365: disable cache usage due to coherency issues
  dm6446: disable cache usage due to coherency issues
  OMAP3: Remove legacy mmc driver
  devkit8000: Use generic MMC driver
  TI OMAP3 SDP3430: Use generic MMC driver
  AM3517 CraneBoard: Use generic MMC driver
  OMAP3: pandora: Use generic MMC driver
  OMAP3: Zoom2: Use generic MMC driver
  OMAP3: Zoom1: Use generic MMC driver
  OMAP3: DIG297: Use generic MMC driver
  OMAP3: CM-T35: Use generic MMC driver
  am3517evm: Use generic MMC driver
  omap3evm: Use generic MMC driver
  omap3:clock: check cpu_family before enabling clks for IVA & CAM
  omap3:clock: configure GFX clock to 200MHz for AM/DM37x
  OMAP3/4: Increase console I/O buffer size
  PXA: vpac270: Remove re-defined CONFIG_SYS_TEXT_BASE
  PXA: Fix CSB226, fix monitor length
  PXA: Fix Lubbock, remove redundant parenthesis
  armv7: cache: remove flush on un-aligned invalidate
  armv7: stronger barrier for cache-maintenance operations
  omap: enable caches at system start-up
  arm: do not force d-cache enable on all boards
  ORIGEN: Add MMC SPL support
  ARMV7: Add support for Samsung ORIGEN board
  i2c:gpio:s5p: Enable I2C GPIO on the GONI target
  i2c:gpio:s5p: I2C GPIO Software implementation (via soft_i2c)
  Tegra2: Use clock and pinmux functions to simplify code
  Tegra2: Add additional pin multiplexing features
  Tegra2: Add more clock support
  Tegra2: Add microsecond timer function
  ARM: remove broken "at91rm9200dk" board
  ARM: remove broken "m501sk" board
  ARM: remove broken "kb9202" board
  ARM: remove broken "csb637" board
  ARM: remove broken "cmc_pu2" board
  ARM: remove broken "at91cap9adk" board
  ARM: remove broken "voiceblue" board
  ARM: remove broken "smdk2400" board
  ARM: remove broken "sbc2410x" board
  ARM: remove broken "netstar" board
  ARM: remove broken "mx1fs2" board
  ARM: remove broken "lpd7a40x" boards
  ARM: remove broken "edb93xx" boards
  ARM: remove broken "B2" board
  ARM: remove broken "armadillo" board
  ARM: remove broken "assabet" board
  ARM: versatile: drop warnings
  IMX: scb9328: drop warnings
  MX31: imx31_litekit: make use of GPIO framework
  MX31: mx31ads: make use of GPIO framework
  MX5: mx51evk: make use of GPIO framework
  MX35: mx35pdk: make use of GPIO framework
  MX5: mx53loco: make use of GPIO framework
  MX5: mx53evk: make use of GPIO framework
  MX5: vision2: make use of GPIO framework
  MX5: mx53smd: make use of GPIO framework
  MX5: mx53ard: make use of GPIO framework
  MX25: zmx25: make use of GPIO framework
  MX5: efikamx: make use of GPIO framework
  MX31: QONG: make use of GPIO framework
  MX35: make use of GPIO framework for MX35 processor
  MX5: make use of GPIO framework for MX5 processor
  MX31: make use of GPIO framework for MX31 processor
  MX25: make use of GPIO framework for MX25 processor
  IMX: uniform GPIO interface using GPIO framework
  MX: MX35 / MX5: uniform clock command with powerpc
  MX35: MX35PDK: support additional RAM on CSD1
  mx53: ddr3: Update DD3 initialization
  ARM: MX51: PLL errata workaround
  ARM: versatilepb : drop warnings due to double definitions
  omap4: increase SRAM budget to fix build error
  omap4: fix build warning due to signed unsigned comparison
  mkimage: Fix 'Unknown OMAP image type - 5'
  omap: fix gpio related build breaks
  gpio:samsung: s5p_ suffix add for GPIO functions (C210_universal)
  SMDKV310: MMC SPL: Remove unwanted dummy functions
  SMDKV310: Fix undefined reference error
  SMDKV310: Fix build error for smdkv310 board
  gpio:samsung s5p_ suffix add for GPIO functions
  mmc: S5P: Support DMA restarts at buffer boundaries
  SMDKV310: Fix host compilation of mkv310_image
  arm: fix bd pointer dereference prior initialization
  arm, lib/board.c: use gd->ram_size instead of bd->bi_memsize
  mx5: Remove CONFIG_L2_OFF and CONFIG_SYS_L2CACHE_OFF
  MX31: removed warnings due to clock.h
  integrator: convert to new build system
  integratorcp: make the board compile
  integratorap: remove hardcoded 32MB memory cmdline
  ...

beagleboard: enable HUB power on all variants of the BeagleBoard

Changes made by Jason Kridner with inputs from Eric Benard to special case xM Rev A and xM Rev B

Relevant discussions:
http://www.mail-archive.com/u-boot@lists.denx.de/msg59361.html
http://www.mail-archive.com/u-boot@lists.denx.de/msg59589.html

Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Christian Spielberger <c.spielberger@bct-electronic.com>
Cc: Jason Kridner <jdk@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

dm3730: enable dpll5

which is used to provide 120MHz to USB EHCI
This allows EHCI to work on BeagleBoard XM

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

ehci-hcd: Allow cleanups to happen gracefully on a timeout.

With this, the EHCI seems to "recover" from a timeout. This is particularly
observable if you were to ping the wrong IP Address and then ping the correct
one or if there was a temporary failure during tftp sessions.

All it takes is one timeout to disable it. If you have a noisy network (lot
of traffic), even if the traffic is not for the board, the timeouts don't occur.

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: Add DSS driver for OMAP3

* Supports dynamic panel configuration
* Supports dynamic tv standard selection
* Adds support for DSS register access through generic APIs
* Incorporated DSS register access using structures.
* DSS makefile update

Previous discussions are here:
http://www.mail-archive.com/u-boot@lists.denx.de/msg27150.html

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

led: Remove state-saving of led for toggle functionality and add toggle option to led command

* Read the led output state from GPIO instead saving state in memory when it is [re]set
* Added a toggle option to the led command

Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html

Changes since v1:
Fixed checkpatch errors

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

led: Fixed setting of STATUS_LED_BIT1 when led_name is 'all'

Fix for only one led getting set or reset when the led_name is 'all'

Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html

Changes since v1:
Fixed checkpatch if statement error noticed by Sergei.

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

led: correct off/on locations in structure

Although the initialization should probably be done with names, the
existing implementation has these structures filled in the opposite
order.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

led: added cmd_led to Makefile

Addition of cmd_led into the Makefile wasn't included in the patch
applied to u-boot-ti.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: fix LED 0/1 in driver

Fixed USR0/USR1 to be LED 0/1 respectively

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Corrected LED name match finding avoiding extraneous Usage printouts

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: updated default configuration

* Improved boot env var setting
    * Made room for a 64MB ramdisk by moving from 0x81600000 to 0x81000000
    * Added ramarg, ramroot and ramboot env variables

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: Enabled multibus support for I2C in configuration

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: add optargs/buddy/camera

buddy and camera are used to configure peripherals in the kernel at boot
time that cannot easily be detected by the kernel.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: increase command-line functionality

Enable the expression evaluator.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: make mtest run

Utilize the alternate mtest and define a valid region.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: enable DSS

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: enable asix driver and dhcp

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: enable networking

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: decrease bootdelay to 2 seconds

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: use uImage.beagle for tftp

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: hardcode MAC for onboard SMSC

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: config: load kernel from MMC ext, not FAT

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: Configure DVI/S-video

Based on patches from Syed Mohammed Khasim (khasim@ti.com).

Configures the output of the BeagleBoard DVI to be orange.
Configures the output of the BeagleBoard S-Video to be a colorbar.

Changed display_init to beagle_display_init as suggested by Igor Grinberg:
http://www.mail-archive.com/u-boot@lists.denx.de/msg51446.html

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: Added userbutton command

Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
    Author: Greg Turner <gregturner@ti.com>
    Date:   Tue May 25 09:19:06 2010 -0500

    New u-boot command for status of USER button on BeagleBoard-xM

         Modified bootcmd to check the staus at boot time and set
 filename of the boot script.

* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
  command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion.  Success (0)
  is when the button is pressed.  Failure (1) is when the button is NOT
  pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
  * Added a separate bootenv variable to load a user defined .txt file
  * Added an example, showing how a different environment file can be loaded with
    the user button pressed

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

BeagleBoard: turn off clocks in ehci_stop

This fixes display problems in linux

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor

Remove __attribute__ ((packed)) to prevent byte access to soc
registers in some gcc versions.

Having patches to enable ehci for the BeagleBoard lying around for
several months, this one was the show-stopper.

Switched to align(4), rather than remove the attribute, per suggestion
from Alexander.

Credits have to go to Laine Walker-Avina <lwalkera@ieee.org> for
finding the problem.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

beagleboard: add support for xM revision C

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

beagle: pass expansionboard name in bootargs

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP: Remove omapfb.debug=y from Beagle and Overo env settings

The kernel DSS2 code is mature now, and keeping this setting hurts performance

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3 Beagle Pin Mux initialization glitch fix

The below patch reverses the order of two segments in the board file.
Output pins need to have their values initialized, before they are
exposed to the logic outside the chip.

Signed-off-by: Bob Feretich <bob.feretich@rafresearch.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: modifications for Logic PD Rev.3 AM18xx EVM

AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: fix the channel number for EMAC teardown init

TX and RX channel numbers programmed as '1' during EMAC
teardown initialization is wrong. This patch fixes the
same by setting channel number to '0' which is used by U-boot.

Signed-off-by: Sugumar Natarajan <sugumar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: add support for Spectrum Digital AM18xx EVM

The AM18xx EVM contains winbond SPI flash instead of ST SPI flash in
comparison with logic PD da850/omap-l138 EVM. So enable configuration
to look for winbond flash.

Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: add support to wake up DSP during board init

add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: modify the U-Boot prompt string

Modify U-Boot prompt string from "DA850-evm >" to "U-Boot >".

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: add NOR boot mode support

Add pin-mux support for NOR in board file and correspanding
macros to use NOR boot mode in configuration file.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da8xx: add support for multiple PLL controllers

Modify clk_get() function in cpu file to work for
multiple PLL controllers.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

da850: indicate cache usage disable in config file

there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for da850 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is  indicated by
the following macro definitions in config file,

1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF

Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

dm365: modify boot prompt from dm365 to dm36x

Newer version for DM365 silicon support higher speeds
and is called DM368. Modify the bootprompt string DM365
to DM36x.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

dm365: disable cache usage due to coherency issues

there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for d365 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is  indicated by
the following macro definitions in config file,

1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF

Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

dm6446: disable cache usage due to coherency issues

there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for dm6446 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is  indicated by
the following macro definitions in config file,

1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF

Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: Remove legacy mmc driver

Now that all platforms have been migrated to the new MMC driver, remove
the old one.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

devkit8000: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

TI OMAP3 SDP3430: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

AM3517 CraneBoard: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: pandora: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: Zoom2: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: Zoom1: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: DIG297: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: CM-T35: Use generic MMC driver

Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

am3517evm: Use generic MMC driver

Switch from the legacy mmc driver to the
new generic mmc driver.

This patch is based on similar patch for beagle[1].

 [1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

omap3evm: Use generic MMC driver

Switch from the legacy mmc driver to the
new generic mmc driver.

This patch is based on similar patch for beagle[1].

 [1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

omap3:clock: check cpu_family before enabling clks for IVA & CAM

In case of AM3517 and AM3505 (which is OMAP3 varients), IVA2 and
ISP-CAMERA modules have been removed. So add check for cpu_family before
enabling clocks for these modules, else this impacts subsequent
power consumption and system suspend/resume functionality.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

omap3:clock: configure GFX clock to 200MHz for AM/DM37x

AM/DM37x is another OMAP3 variant, where the GFX clock has been
boosted to 192MHz/200MHz. So fix the GFX_DIV value for this change.

HW Errata: Due to dependency of TV out clock of 54MHz, it is not
possible to configure GFX to 192MHz. So as per HW errats, the
recommended GFX clock is 200MHz (=CORE_CLK/2).

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3/4: Increase console I/O buffer size

Increase the console I/O buffer size (SYS_CBSIZE) to 512 (from 256)
required especially for bootargs string, as multiple options
(e.g Video settings) are passed to the kernel through bootargs.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

PXA: vpac270: Remove re-defined CONFIG_SYS_TEXT_BASE

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

PXA: Fix CSB226, fix monitor length

This is what was probably intended by the original author.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

PXA: Fix Lubbock, remove redundant parenthesis

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

armv7: cache: remove flush on un-aligned invalidate

Remove the flush of boundary cache-lines done as part
of invalidate on a non cache-line boundary aligned
buffer

Also, print a warning when this situation is recognized.

Signed-off-by: Aneesh V <aneesh@ti.com>

armv7: stronger barrier for cache-maintenance operations

set-way operations need a DSB after them to ensure the
operation is complete. DMB may not be enough. Use DSB
after all operations instead of DMB.

Signed-off-by: Aneesh V <aneesh@ti.com>

omap: enable caches at system start-up

Signed-off-by: Aneesh V <aneesh@ti.com>

arm: do not force d-cache enable on all boards

c2dd0d45540397704de9b13287417d21049d34c6 added dcache_enable()
to board_init_r(). This enables d-cache for all ARM boards.
As a result some of the arm boards that are not cache-ready
are broken. Revert this change and allow platform code to
take the decision on d-cache enabling.

Also add some documentation for cache usage in ARM.

Signed-off-by: Aneesh V <aneesh@ti.com>

ORIGEN: Add MMC SPL support

Adds mmc boot support.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

ARMV7: Add support for Samsung ORIGEN board

Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

i2c:gpio:s5p: Enable I2C GPIO on the GONI target

This patch enables the software I2C for GONI reference target.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>

i2c:gpio:s5p: I2C GPIO Software implementation (via soft_i2c)

This patch adds support for software I2C for GONI and Universal C210 reference targets.
It adds support for access to GPIOs by number, not as it is present,
by bank and offset.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>

Tegra2: Use clock and pinmux functions to simplify code

Signed-off-by: Simon Glass <sjg@chromium.org>

Tegra2: Add additional pin multiplexing features

This adds an enum for each pin and some functions for changing the pin
muxing setup.

Signed-off-by: Simon Glass <sjg@chromium.org>

Tegra2: Add more clock support

This adds functions to enable/disable clocks and reset to on-chip peripherals.

Signed-off-by: Simon Glass <sjg@chromium.org>

Tegra2: Add microsecond timer function

These functions provide access to the high resolution microsecond timer
and tidy up a global variable in the code.

Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: remove broken "at91rm9200dk" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "m501sk" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "kb9202" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "csb637" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "cmc_pu2" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "at91cap9adk" board

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stelian Pop <stelian.pop@leadtechdesign.com>

ARM: remove broken "voiceblue" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "smdk2400" board

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Gary Jennejohn <garyj@denx.de>

ARM: remove broken "sbc2410x" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "netstar" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "mx1fs2" board

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "lpd7a40x" boards

Remove lpd7a400 and lpd7a404 boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "edb93xx" boards

Remove edb9301, edb9302, edb9302a, edb9307, edb9307a, edb9312,
edb9315 and edb9315a boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: remove broken "B2" board

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>

ARM: remove broken "armadillo" board

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rowel Atienza <rowel@diwalabs.com>

ARM: remove broken "assabet" board

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: George G. Davis <gdavis@mvista.com>

ARM: versatile: drop warnings

Drop warning: "passing argument 1 of 'get_ram_size'
discards qualifiers from pointer target type"

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>

IMX: scb9328: drop warnings

Drop warning: "passing argument 1 of 'get_ram_size'
discards qualifiers from pointer target type"

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Torsten Koschorrek <koschorrek@synertronixx.de>

MX31: imx31_litekit: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>

MX31: mx31ads: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>

MX5: mx51evk: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>

MX35: mx35pdk: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>

MX5: mx53loco: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <r64343@freescale.com>

MX5: mx53evk: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <r64343@freescale.com>

MX5: vision2: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>

MX5: mx53smd: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>

MX5: mx53ard: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>

MX25: zmx25: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>

MX5: efikamx: make use of GPIO framework

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>