Troy Kisky [Mon, 29 Jul 2019 19:15:57 +0000 (12:15 -0700)]
configs: nitrogen6x: Add DM_GPIO support
Add CONFIG_DM_GPIO to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
This is in preparation for adding CONFIG_DM_SPI.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Troy Kisky [Mon, 29 Jul 2019 19:15:56 +0000 (12:15 -0700)]
nitrogen6x: reserve used gpios
This prevents messages like
gpio@
20a0000: get_value: error: gpio GPIO2_2 not reserved
when CONFIG_DM_GPIO is enabled.
Also, when CONFIG_DM_GPIO is enabled, checkboard is too
early to use gpio_get_value, so read it directly on failure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Troy Kisky [Mon, 29 Jul 2019 19:15:55 +0000 (12:15 -0700)]
configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI support
Add DM_MMC to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
This commit is adding multiple configs, but
seems to be the minimum change to not lose features
and still compile fine.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Troy Kisky [Mon, 29 Jul 2019 19:15:54 +0000 (12:15 -0700)]
nitrogen6x: migrate to using device tree
Migrate to using device tree required for further driver model
integration.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Robert Hancock [Thu, 8 Aug 2019 18:14:39 +0000 (12:14 -0600)]
ARM: imx: Support larger SPL size on IMX6DQ
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
Ricardo Salveti [Mon, 2 Sep 2019 21:18:52 +0000 (18:18 -0300)]
spl: imx: only use HAB if spl fit signature is not enabled
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ricardo Salveti [Mon, 2 Sep 2019 21:26:15 +0000 (18:26 -0300)]
imx: apalis_imx6: select MX6Q via Kconfig
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Ricardo Salveti [Mon, 2 Sep 2019 21:12:02 +0000 (18:12 -0300)]
apalis_imx6: fix broken fsl_esdhc_imx conversion
Commit
e37ac717d796 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Ricardo Salveti [Mon, 2 Sep 2019 21:23:27 +0000 (18:23 -0300)]
apalis_imx6: add board_fit_config_name_match to support FIT in SPL
Only one dtb is currently supported, so match with imx6-apalis.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Peng Fan [Wed, 24 Jul 2019 08:53:08 +0000 (08:53 +0000)]
arm: dts: imx: fsl-imx8qm.dtsi: add gpio aliases to fix gpio command
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Peng Fan [Wed, 7 Aug 2019 06:40:53 +0000 (06:40 +0000)]
spl: pass args to board_return_to_bootrom
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peng Fan [Wed, 7 Aug 2019 06:49:39 +0000 (06:49 +0000)]
serial: Kconfig: make MXC_UART usable for MX7 and IMX8M
i.MX7 and i.MX8M use mxc uart driver, so let's make the SoC could
use MXC_UART kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Peng Fan [Tue, 6 Aug 2019 10:07:26 +0000 (10:07 +0000)]
tools: imx8mimage: fix HDMI/FIT parsing
Add missed break for HDMI entry.
And moving FIT parsing earlier, because it does not have parameter,
it will not runs into CFG_REG_SIZE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Peng Fan [Tue, 6 Aug 2019 10:05:48 +0000 (10:05 +0000)]
pinctrl: imx: use devfdt_get_addr_size_index
fdtdec_get_addr_size could not parse addr/size correctly is
using address-cells 2 and size-cells 2 on an ARM32 SoC.
So switch to use devfdt_get_addr_size_index.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 31 Jul 2019 08:30:02 +0000 (08:30 +0000)]
imx: mx6slevk: enable DM_SPI and DM_SPI_FLASH
With DM_SPI and DM_SPI_FLASH enabled, we could get:
spi 0 [ ] mxc_spi | | | `-- ecspi@
02008000
spi_flash 0 [ ] spi_flash_std | | | `-- m25p80@0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Thu, 1 Aug 2019 06:02:49 +0000 (06:02 +0000)]
imx: mx6ul_14x14_evk: convert to DM_VIDEO
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Peng Fan [Thu, 1 Aug 2019 06:02:41 +0000 (06:02 +0000)]
imx: mx6ul_14x14_evk: Fix SPL boot
When booting SPL on the board, met boot failure:
"
Trying to boot from MMC2
MMC Device 1 not found
spl: could not find mmc device 1. error: -19
SPL: failed to boot from all boot devices
"
Let's register the two mmc controllers in SPL stage to
avoid boot failure.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:57 +0000 (09:55 +0000)]
imx: add i.MX6ULZ board
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:52 +0000 (09:55 +0000)]
imx: add i.MX6ULZ cpu type
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:47 +0000 (09:55 +0000)]
arm: dts: import dts for i.MX6ULZ
Import kernel dts for i.MX6ULZ from
commit <
0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:37 +0000 (09:55 +0000)]
arm: dts: sync dts for i.MX6ULL
Sync kernel dts for i.MX6ULL from
commit <
0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:33 +0000 (09:55 +0000)]
arm: dts: sync dts for i.MX6UL
Sync kernel dts for i.MX6UL from
commit <
0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tom Rini [Mon, 7 Oct 2019 21:14:02 +0000 (17:14 -0400)]
Prepare v2019.10
Signed-off-by: Tom Rini <trini@konsulko.com>
Eugeniy Paltsev [Mon, 7 Oct 2019 16:10:50 +0000 (19:10 +0300)]
NET: DW: fix regression for ARC boards
The commit
642b80d256e ("net: designware: drop compatible altr, socfpga-stmmac")
breaks designware ethernet for all ARC boards. It removes
"altr, socfpga-stmmac" compatible from "drivers/net/designware.c"
without changing compatible in the boards which use it.
Fix that by adding "snps,arc-dwmac-3.70a" compatible string to
"drivers/net/designware.c" and using it in ARC boards device tree.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Tom Rini [Sun, 6 Oct 2019 22:02:18 +0000 (18:02 -0400)]
Merge branch '2019-10-06-master-imports'
- Regression work-around on SoCFPGA by disabling WDT in some cases.
- Fix seg fault on 'host info' in some cases.
AKASHI Takahiro [Thu, 22 Aug 2019 07:47:39 +0000 (16:47 +0900)]
cmd: host: fix seg fault at "host info"
With the patch below applied, host_block_dev structure was switched
to be placed in platdata rather than priv. The command "host info"
must be aligned with this change. Otherwise, we will see "Segmentation
Fault."
Fixes:
8f994c860d91 ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Maxime Ripard [Thu, 3 Oct 2019 16:32:11 +0000 (18:32 +0200)]
MAINTAINERS: Update my email address
I'm not at bootlin anymore, and my mail address doesn't work any longer.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Simon Goldschmidt [Sat, 5 Oct 2019 20:10:11 +0000 (22:10 +0200)]
arm: socfpga: disable CONFIG_SPL_WDT for gen5 and a10
These boards don't have a watchdog enabled in SPL, so make sure
CONFIG_SPL_WDT is not enabled.
Fixes: commit
6874cb72204f ("watchdog: Split WDT from SPL_WDT")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Heinrich Schuchardt [Sun, 6 Oct 2019 10:26:16 +0000 (12:26 +0200)]
gitlab-ci: fix typo 'plaforms'
%s/plaforms/platforms/g
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sun, 6 Oct 2019 00:06:58 +0000 (20:06 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
- ARM: dts: rmobile: Restore increase off-on delay on the SD Vcc regulator
Tom Rini [Fri, 4 Oct 2019 16:22:43 +0000 (12:22 -0400)]
Merge branch '2019-10-04-master-imports'
- Assorted TI platform fixes
- Revert the change that broke environment flag validation
- Assorted typo fixes
- Assorted Kconfig dependency fixes
- Other minor bug fixes
Tom Rini [Fri, 4 Oct 2019 16:22:28 +0000 (12:22 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- dm: core: Correct low cell in ofnode_read_pci_addr()
- dm: core: Correct bad cast in ofnode_get_addr_size_index()
Tom Rini [Fri, 4 Oct 2019 16:21:33 +0000 (12:21 -0400)]
Revert "env: solve compilation error in SPL"
This reverts commit
7d4776545b0f8a8827e5d061206faf61c9ba6ea9. The
changes here break environment validation and furthermore do not seem to
be required.
Signed-off-by: Tom Rini <trini@konsulko.com>
Adam Ford [Wed, 7 Aug 2019 15:16:33 +0000 (10:16 -0500)]
ARM: dts: imx6q-logicpd: Add missing imx6q-logicpd-u-boot for SPL
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes:
8f4691e31a18 ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <aford173@gmail.com>
Ovidiu Panait [Wed, 25 Sep 2019 11:10:54 +0000 (14:10 +0300)]
initcall.h: initcall_run_list(): Improve debug output
Existing debug output is mixed with the function name:
initcall_run_list() initcall: 25263initcall_run_list() (relocated to 425263)
Turn it to:
initcall_run_list() initcall: 25263 (relocated to 425263)
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Andrius Štikonas [Mon, 23 Sep 2019 21:43:41 +0000 (22:43 +0100)]
Kconfig: fix a typo in the description of bmp command.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Tom Rini [Fri, 20 Sep 2019 21:36:50 +0000 (17:36 -0400)]
Kconfig: Migrate CONFIG_BOOTM_* options
Migrate all of the existing OS support options that are under
CONFIG_BOOTM_* to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Roman Stratiienko [Fri, 20 Sep 2019 13:59:18 +0000 (15:59 +0200)]
cmd: part: number: return hexadecimal value
At this point we are using part number sub-command to retrieve UUID
of the partition using it's name.
e.g.:
part number mmc $mmcdev system_a system_a_index
part uuid mmc $mmcdev:${system_a_index} system_a_uuid
Since 'part uuid' sub-command expects partition index in hex format and
'part number' returns decimal value, 'part uuid' command will provide
wrong UUID or fail.
Fixes:
be683756f62034 ("cmd: part: Add 'number' sub-command")
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Pontus Fuchs <pontus.fuchs@se.bosch.com>
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Jean-Jacques Hiblot [Tue, 17 Sep 2019 21:18:25 +0000 (17:18 -0400)]
ARM: keystone2: update the default addresses of the secure monitor
To accommodate the growth of u-boot, we need to shift the location of the
secure monitor. Moving it 64kB further.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Andrew F. Davis [Tue, 17 Sep 2019 21:15:40 +0000 (17:15 -0400)]
board: ti: am654: Disable TRNG node for HS devices
On HS devices the access to TRNG is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
AKASHI Takahiro [Thu, 12 Sep 2019 06:31:22 +0000 (15:31 +0900)]
autoboot: add necessary dependency at AUTOBOOT_MENU_SHOW
Otherwise, menu_show() will be undefined in bootdelay_process().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Ley Foon Tan [Fri, 4 Oct 2019 08:43:50 +0000 (16:43 +0800)]
MAINTAINERS, git-mailrc: Update the maintainer for socfpga
This updates MAINTAINERS and git-mailrc to add me as maintainer for
socfpga.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Heinrich Schuchardt [Thu, 3 Oct 2019 16:45:29 +0000 (16:45 +0000)]
Makefile: mrproper should remove *.pyc files
*.pyc files contain compiled Python bytecode. 'make mrproper' should remove
them.
Removing *.pyc files helps for instance sometimes when running into an
error "binman: Unknown entry type 'blob' in node '/binman/blob'".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Michal Simek [Wed, 2 Oct 2019 13:53:12 +0000 (15:53 +0200)]
Makefile: Fix typo around CONFIG_SPL_FIT_SOURCE
Trivial fix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Andrew F. Davis [Tue, 1 Oct 2019 14:33:43 +0000 (10:33 -0400)]
arm: K3: Increase default SYSFW image size allocation
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 269000 bytes but now needs to be grown to 276000 to make room
for the signatures attached to the board configuration data on High
Security devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Simon Glass [Wed, 25 Sep 2019 14:55:50 +0000 (08:55 -0600)]
dm: core: Correct bad cast in ofnode_get_addr_size_index()
At present this code passes an fdt_addr_t pointer as a u64 pointer which
is not safe, since sizeof(fdt_addr_t) may be 4, e.g. with sandbox. Correct
this to avoid a stack corruption problem.
Fixes:
e679d03b08 (core: ofnode: Add ofnode_get_addr_size_index)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 25 Sep 2019 14:55:46 +0000 (08:55 -0600)]
dm: core: Correct low cell in ofnode_read_pci_addr()
This reads the low cell of the PCI address from the wrong cell. Fix it.
Also fix the function that this code came from.
Fixes:
9e51204527 (dm: core: Add operations on device tree references)
Fixes:
4ea5243a3a (fdt: fix fdtdec_get_pci_addr() for CONFIG_PHYS_64BIT)
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Tue, 1 Oct 2019 20:31:26 +0000 (16:31 -0400)]
Merge tag 'rpi-next-2019.10.2' of https://github.com/mbgg/u-boot
RPi4:
Fix amount of memory seen by the kernel.
Tom Rini [Tue, 1 Oct 2019 20:31:11 +0000 (16:31 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Propagate acpi_rsdp_addr to x86 kernel via boot parameters
Andy Shevchenko [Fri, 13 Sep 2019 15:42:00 +0000 (18:42 +0300)]
x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parameters
This is reincarnation of the U-Boot
commit
3469bf4274540d1491d58e878a9edc0bdcba17ac
Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Date: Wed Jan 10 19:40:15 2018 +0200
x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parameters
after upstream got eventually the Linux kernel
commit
e6e094e053af75cbc164e950814d3d084fb1e698
Author: Juergen Gross <jgross@suse.com>
Date: Tue Nov 20 08:25:29 2018 +0100
x86/acpi, x86/boot: Take RSDP address from boot params if available
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Matthias Brugger [Mon, 9 Sep 2019 16:31:56 +0000 (18:31 +0200)]
rpi4: enable dram bank initialization
When booting through the efi stub, the memory map get's created by
reading the dram bank information. Depending on the version of the RPi4
this information changes. Read the device tree to initialize the dram
bank data structure. This way the kernel is able to access the whole
range of available memory.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tom Rini [Mon, 30 Sep 2019 11:21:38 +0000 (07:21 -0400)]
Merge tag 'u-boot-atmel-fixes-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2019.10 cycle:
This includes only tiny cleanups on env changes related to 2019.10 new
features: removal of duplicate env settings (otherwise there may be
warnings in building..) and a small fix for flashes on Gardena smart
gateway (requires nand bad block tables).
Tom Rini [Mon, 30 Sep 2019 11:20:35 +0000 (07:20 -0400)]
Merge tag 'u-boot-rockchip-
20190928' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fix efuse read data number for rk3399
- make_fit_atf.py: fix .its generation for a single atf image
Tudor Ambarus [Fri, 20 Sep 2019 10:52:58 +0000 (10:52 +0000)]
at91: configs: Drop duplication of defconfig macros
'commit
a9221f3ebd6d ("at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs")'
migrated CONFIG_ENV_ macros to defconfigs but did not remove the
identical redefinition of these macros in include/configs/.
Since the duplicated macros have the same value as the ones in defconfigs,
no "redefined" warnings were raised. Remove duplicated macros for all
sama5 and sam9x5ek boards.
While verifying that the removal of the macros from include/configs did
not change the same macros in defconfigs, overwrite the old defconfig by
saving them with the output from "make arch=ARM savedefconfig". This
resulted in the movement of some macros in the defconfig files.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Stefan Roese [Tue, 27 Aug 2019 06:14:50 +0000 (08:14 +0200)]
arm: at91: gardena-smart-gateway-at91sam: Enable CONFIG_SYS_NAND_USE_FLASH_BBT
This patch enables the BBT in NAND on the AT91SAM based GARDENA smart
Gateway. This is especially important, since the Linux driver also
enables this option and uses the BBT table pages. Without setting this
option, U-Boot will try to re-use these pages again (e.g. UBI).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Mon, 18 Mar 2019 02:20:31 +0000 (03:20 +0100)]
ARM: dts: rmobile: Restore increase off-on delay on the SD Vcc regulator
This patch restores commit
c49d0ac38a76 ("ARM: dts: rmobile: Increase off-on
delay on the SD Vcc regulator"), which was accidentally dropped during DT
resync in commit
317d13ac6307 ("ARM: dts: rmobile: Synchronize Gen3 DTs with
Linux 5.0").
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fixes:
317d13ac6307 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
Heiko Stuebner [Thu, 26 Sep 2019 19:15:15 +0000 (21:15 +0200)]
rockchip: make_fit_atf.py: fix .its generation for a single atf image
The commit
619f002db864 ("rockchip: make_fit_atf.py: fix loadables property
set error") fixed the double-loading of the primary atf-image, but didn't
take into account that there may be rare atf images with only that main
section present.
Right now this will result in a broken its due to the loadables section not
getting closed correctly, so fix that by adapting the guards around the loop.
The guards now protect against 0 segments when the bl31 binary doesn't
contain any section and 1 segment when only a core atf section is present.
Fixes:
619f002db864 ("rockchip: make_fit_atf.py: fix loadables property set error")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Heiko Stuebner [Wed, 25 Sep 2019 18:40:56 +0000 (20:40 +0200)]
rockchip: misc: read the correct number of bytes from the efuse
Originally the cpuid var the value gets read into was defined as
u8 cpuid[RK3399_CPUID_LEN];
hence the sizeof(cpuid) would return the correct the correct number
of array elements.
With the move to a separate function cpuid becomes a pointer and
sizeof(cpuid) hence returns the pointer size - 8 in the arm64 case.
We do have the actual id length available as function param so use
it for actual amount of bytes to read.
Fixes:
04825384999f ("rockchip: rk3399: derive ethaddr from cpuid")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Tom Rini [Thu, 26 Sep 2019 21:22:22 +0000 (17:22 -0400)]
Merge tag 'efi-2019-10-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc5
Bug fixes for the SetVariable() boot service.
Pierre-Jean Texier [Mon, 26 Aug 2019 11:06:18 +0000 (13:06 +0200)]
ci: add envtools support
This commit add envtools suppport to CI to verify if there
is no build issues.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pierre-Jean Texier [Mon, 26 Aug 2019 11:06:17 +0000 (13:06 +0200)]
env: add missing <compiler.h> header file
Since commit
af95f20 ("env: Create a new file for environment functions"),
a new header file exists.
So, this commit add a missing header file.
Fixes:
include/env.h:158:1: error: unknown type name ‘ulong’; did you mean ‘long’?
ulong env_get_ulong(const char *name, int base, ulong default_val);
^~~~~
long
include/env.h:158:49: error: unknown type name ‘ulong’; did you mean ‘long’?
ulong env_get_ulong(const char *name, int base, ulong default_val);
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pierre-Jean Texier [Mon, 26 Aug 2019 11:06:16 +0000 (13:06 +0200)]
fw_env: fix build error
The following error appears:
tools/env/fw_env.c:1149:25: error: lvalue required as unary ‘&’ operand
rc = write(fd, &ENV_REDUND_OBSOLETE, sizeof(ENV_REDUND_OBSOLETE));
Fixes:
d3716dd ("env: Rename the redundancy flags")
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Suggested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pierre-Jean Texier [Mon, 26 Aug 2019 11:06:15 +0000 (13:06 +0200)]
fw_env: remove duplicated definitions
Since commit
d3716dd ("env: Rename the redundancy flags"), the
definitions of ENV_REDUND_OBSOLETE & ENV_REDUND_ACTIVE was moved
to env.h.
Fixes:
tools/env/fw_env.c:122:22: error: ‘ENV_REDUND_ACTIVE’ redeclared as different kind of symbol
static unsigned char ENV_REDUND_ACTIVE = 1;
^~~~~~~~~~~~~~~~~
In file included from tools/env/fw_env.c:13:
include/env.h:63:2: note: previous definition of ‘ENV_REDUND_ACTIVE’ was here
ENV_REDUND_ACTIVE = 1,
^~~~~~~~~~~~~~~~~
tools/env/fw_env.c:127:22: error: ‘ENV_REDUND_OBSOLETE’ redeclared as different kind of symbol
static unsigned char ENV_REDUND_OBSOLETE;
^~~~~~~~~~~~~~~~~~~
In file included from tools/env/fw_env.c:13:
include/env.h:62:2: note: previous definition of ‘ENV_REDUND_OBSOLETE’ was here
ENV_REDUND_OBSOLETE = 0,
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Heinrich Schuchardt [Mon, 23 Sep 2019 20:38:53 +0000 (22:38 +0200)]
efi_loader: SetVariable() deleting variables
APPEND_WRITE with data length zero is allowable according to the UEFI
specification.
The EDK2 interpretation of no access attributes is attributes = 0. As
the UEFI specification is vague in this respect let's stick to EDK2 here.
Fixes: commit
6d2f27c5fd60 ("efi_loader: variable: support APPEND_WRITE")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 23 Sep 2019 20:18:09 +0000 (22:18 +0200)]
efi_loader: SetVariable() fix illegal return
We always have to return via EFI_EXIT() from EFIAPI functions.
Coverity reported an unreachable line and a resource leak.
Fixes: commit
6d2f27c5fd60 ("efi_loader: variable: support APPEND_WRITE")
Reported-by: Coverity Scan CID 253575, CID 184095
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 21 Sep 2019 04:38:11 +0000 (06:38 +0200)]
efi_loader: description efi_stri_coll()
Remove outdated TODO for efi_stri_coll(). efi_stri_coll() is already using
the Unicode capitalization table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Mon, 23 Sep 2019 16:24:39 +0000 (12:24 -0400)]
Prepare v2019.10-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 23 Sep 2019 15:47:37 +0000 (11:47 -0400)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sun, 22 Sep 2019 20:39:01 +0000 (16:39 -0400)]
Merge tag 'fixes-for-2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-video.git
- fix sunxi LCD clock divider
- fix splash logo with DM_VIDEO and CONFIG_VIDEO_LOGO
- fix splash banner output with DM_VIDEO
Tom Rini [Sat, 21 Sep 2019 11:31:23 +0000 (07:31 -0400)]
Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function to
compare u16 strings which is prerequisite for further patches.
Mark Kettenis [Fri, 9 Aug 2019 20:30:26 +0000 (22:30 +0200)]
sunxi: video: HDMI: Fix LCD clock divider
Currently we may end up with an LCD clock divider that differs from
the HDMI PHY clock divider if we can't exactly match the pixel clock.
Fix this by using DIV_ROUND_UP to calculate the divider. This works
since the PLL is chosen such that the resulting pixel clock is
never higher than the requested pixel clock.
Fixes:
1feed358ed15 ("sunxi: video: HDMI: Fix clock setup")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Anatolij Gustschin [Fri, 20 Sep 2019 15:23:41 +0000 (17:23 +0200)]
splash: fix splash banner output
Old splash code in cfb_console driver displayed U-Boot version
string by default. Restore this behaviour for DM_VIDEO enabled
configurations.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Anatolij Gustschin [Wed, 18 Sep 2019 15:40:21 +0000 (17:40 +0200)]
imx: mx6sabreauto: fix splash logo drawing
Enable BMP code. Also configure white on black for video console.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Wed, 18 Sep 2019 15:31:52 +0000 (17:31 +0200)]
imx: colibri_imx6: fix splash logo drawing
Define "splashimage" variable in the default environment
to enable splash screen drawing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Wed, 18 Sep 2019 15:23:45 +0000 (17:23 +0200)]
imx: icore: fix splash logo drawing
Define "splashimage" variable in the default environment
and enable BMP code. Also configure white on black for
video console.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Thu, 19 Sep 2019 15:19:01 +0000 (17:19 +0200)]
imx: apalis_imx6: fix splash logo drawing
Define "splashimage" variable in the default environment
to enable splash screen drawing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Wed, 18 Sep 2019 15:05:31 +0000 (17:05 +0200)]
imx: mx6sabresd: fix splash logo drawing
After mxc_ipuv3 DM_VIDEO conversion showing splash image
doesn't work. Fix this. Also enable white on black console
configuration as it used to be with cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Anatolij Gustschin [Wed, 18 Sep 2019 14:55:49 +0000 (16:55 +0200)]
imx: wandboard: fix splash logo drawing
After mxc_ipuv3 DM_VIDEO conversion showing splash image
doesn't work. Fix this. Also enable white on black console
configuration as it used to be with cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Wed, 18 Sep 2019 14:47:33 +0000 (16:47 +0200)]
splash: fix logo drawing if CONFIG_VIDEO_LOGO enabled
After mxc_ipuv3 DM_VIDEO conversion board configs with enabled
CONFIG_VIDEO_LOGO do not show splash screen (previosly drawing
splash screen worked via cfb_console driver with CONFIG_VIDEO_LOGO
enabled). Use splash_source library for loading splash images
when CONFIG_SPLASH_SOURCE is selected, otherwise prepare built-in
video logo for drawing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tom Rini [Fri, 20 Sep 2019 21:43:33 +0000 (17:43 -0400)]
Merge tag 'u-boot-rockchip-
20190920' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fix rk3288 tinker and evb SPL boot fail
- Enable get sn from cpuid for rk3399 rockpro64 board
AKASHI Takahiro [Wed, 18 Sep 2019 01:26:30 +0000 (10:26 +0900)]
test: add tests for u16_str<n>cmp()
New seven test cases for u16_str<n>cmp() are added under Unicode unit test,
which should be executed by "ut unicode" command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Wed, 18 Sep 2019 01:26:29 +0000 (10:26 +0900)]
lib: charset: add u16_str<n>cmp()
u16 version of strcmp(): u16_strncmp() works like u16_strcmp() but only
at most n characters (in u16) are compared.
This function will be used in my UEFI secure boot patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Fri, 6 Sep 2019 06:09:53 +0000 (15:09 +0900)]
efi_loader: selftest: enable APPEND_WRITE tests
Now that APPEND_WRITE is supported,
the result check for the only existing test case should be changed to
'todo' to 'error', while two more test cases are added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Fri, 6 Sep 2019 06:09:52 +0000 (15:09 +0900)]
efi_loader: variable: support APPEND_WRITE
If EFI_VARIABLE_APPEND_WRITE is specified in attributes at
efi_set_variable(), specified data will be appended to the variable's
original value. Attributes other than APPEND_WRITE should not be
modified.
With this patch, APPEND_WRITE test in 'variables' selftest will pass.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Heinrich Schuchardt [Fri, 13 Sep 2019 16:20:40 +0000 (18:20 +0200)]
efi_loader: incorrect return value form DisconnectController
DisconnectController() should never return EFI_NOT_FOUND.
If EFI_DRIVER_BINDING_PROTOCOL.Stop() fails, return EFI_DEVICE_ERROR.
If the driver handle does not expose the EFI_DRIVER_BINDING_PROTOCOL
return EFI_INVALID_PARAMETER.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Thu, 12 Sep 2019 04:52:35 +0000 (13:52 +0900)]
efi_loader: device_path: support Sandbox's "host" devices
Sandbox's "host" devices are currently described as UCLASS_ROOT udevice
with DEV_IF_HOST block device. As the current implementation of
efi_device_path doesn't support such a type, any "host" device
on sandbox cannot be seen as a distinct object.
For example,
=> host bind 0 /foo/disk.img
=> efi devices
Scanning disk host0...
Found 1 disks
Device Device Path
================ ====================
0000000015c19970 /VenHw(
e61d73b9-a384-4acc-aeab-
82e828f3628b)
0000000015c19d70 /VenHw(
e61d73b9-a384-4acc-aeab-
82e828f3628b)
=> efi dh
Handle Protocols
================ ====================
0000000015c19970 Device Path, Device Path To Text, Device Path Utilities, Unicode Collation 2, HII String, HII Database, HII Config Routing
0000000015c19ba0 Driver Binding
0000000015c19c10 Simple Text Output
0000000015c19c80 Simple Text Input, Simple Text Input Ex
0000000015c19d70 Block IO, Device Path, Simple File System
As you can see here, efi_root (0x0000000015c19970) and host0 device
(0x0000000015c19d70) have the same representation of device path.
This is not only inconvenient, but also confusing since two different
efi objects are associated with the same device path and
efi_dp_find_obj() will possibly return a wrong result.
Solution:
Each "host" device should be given an additional device path node
of "vendor device path" to make it distinguishable.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 20 Sep 2019 14:47:03 +0000 (10:47 -0400)]
Merge branch '2019-09-19-master-imports'
- Coding style corrections in some RTC drivers.
- Small doc updates.
- Regression fix in part_test_dos()
- Regression fix on TI OMAP WDTs.
- Document deadline for CONFIG_DM migration.
- Switch Travis-CI to "xenial" release.
Heinrich Schuchardt [Mon, 16 Sep 2019 16:41:42 +0000 (18:41 +0200)]
dm: MIGRATION: Add migration plan for CONFIG_DM
For many sub-systems we already require the driver model to be used. Yet
there is still a handful of boards that do not have CONFIG_DM enabled.
We should make CONFIG_DM compulsory with release v2020.01
Conversion dates for CONFIG_DM_SPL and CONFIG_DM_TPL are yet to be defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Suniel Mahesh [Mon, 16 Sep 2019 08:09:17 +0000 (13:39 +0530)]
watchdog: omap_wdt: Fix WDT target reset when booted from emmc
AM335X based beaglebone black target gets reset by DM converted watchdog
if booted from emmc around 60sec. Fixed this by moving driver's private struct
variable initialization at different places in the driver to driver's probe.
Tested on Beaglebone Black.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes:
7659ea32 ("watchdog: omap_wdt: Convert watchdog driver to use DT and DM")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tom Rini [Fri, 13 Sep 2019 15:51:42 +0000 (11:51 -0400)]
scrapyard: Delete this file and script
The README.scrapyard file has been inconsistently updated. While well
intentioned, bad data is worse than no data, and in this case a pointer
to use the history that git provides. Remove the current content and
the script that would update it from time to time as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Faiz Abbas [Wed, 4 Sep 2019 14:40:12 +0000 (20:10 +0530)]
disk: part_dos: Allocate at least one block size for mbr
The blk_dread() following the mbr allocation reads one block from the
device. This will lead to overflow if block size is greater than the
size of legacy_mbr. Fix this by allocating at least one block size.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Lukasz Majewski [Tue, 3 Sep 2019 13:43:55 +0000 (15:43 +0200)]
kconfig: doc: Update comment regarding CONFIG_IS_ENABLED(FOO) for TPL
This patch adds some commit info for CONFIG_IS_ENABLED(FOO) when used in
TPL context.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Tue, 3 Sep 2019 13:43:19 +0000 (15:43 +0200)]
doc: fix: Replace SPL_OF_PLATDATA with OF_PLATDATA in examples
The of-plat.rst file till this change has been using
This is at best misleading as SPL_OF_PLATDATA is always defined when we
want to use this SPL tinification feature (also in U-Boot proper).
As a result the OF_PLATDATA SPL specific code is also compiled in when
U-Boot proper is build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Biwen Li [Tue, 27 Aug 2019 07:32:36 +0000 (15:32 +0800)]
rtc: ds3231/ds3232: fix coding style
The patch fixes coding style
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Ramon Fried [Mon, 12 Aug 2019 17:43:38 +0000 (20:43 +0300)]
travis.yml: change Ubuntu version to xenial
trusty is getting old, move to xenial (16.04)
to get updated gcc and other tools.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Kever Yang [Wed, 18 Sep 2019 09:56:42 +0000 (17:56 +0800)]
rockchip: config: evb-rk3288: enable SPL_STACK_R
We need a new STACK in SDRAM instead of SRAM so that the EMMC controller
can work properly. The EMMC/SD controller's master is not able to access
SRAM area, it can only access DRAM area.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Wed, 18 Sep 2019 09:56:41 +0000 (17:56 +0800)]
rockchip: evb-rk3288: Drop explicit SPL_TEXT
SPL_TEXT_BASE is 0x0 by default, based on the kconfig
definition move in below commit.
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1:
f89d6133eef2e068f9c33853b6584d7fcbfa9d2e)
So, don't define it explicitly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 17 Sep 2019 07:29:29 +0000 (12:59 +0530)]
configs: rk3288: Increase bootm length
Increase bootm length to 64MB satisfy max gunzip
size, even other rockchip and know SoC are following
same length check.
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Michael Trimarchi [Tue, 17 Sep 2019 06:10:42 +0000 (11:40 +0530)]
rockchip: rk3288-tinker: Attach missing peripherals at SPL
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Jagan Teki [Tue, 17 Sep 2019 06:10:41 +0000 (11:40 +0530)]
configs: tinker: Enable SDRAM, SPL stack
SPL sets up SDRAM while in its board_init_f()
function, it is possible for the stack to move
there before board_init_r() is reached.
So it is required to reserve the stack for SDRAM,
with a proper location and size otherwise any
operations during SPL handoff would leads to failure.
On, this particular context tinker-rk3288 SPL is
failing to launch U-Boot proper on SDRAM due to
lack of stack.
U-Boot SPL
2019.10-rc3-00297-g5ba8b12543 (Sep 12 2019 - 08:50:36 +0530)
Trying to boot from MMC1
spl: mmc init failed with error: -110
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
So, enable SPL_STACK_R_ADDR and it's related-config
items for SDRAM, SPL stack to setup properly.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>