git.librecmc.org Git - oweals/u-boot.git/log

lib/physmem.c: Switch to __weak for arch_phys_memset

We normally use __weak rather than calling it out directly as an alias.
Update this function to the normal method.

Signed-off-by: Tom Rini <trini@konsulko.com>

post: Delete unnecessary bitmask of POST_MANUAL from POST_ALWAYS

Since POST_ALWAYS is defined as:

#define POST_ALWAYS             (POST_NORMAL    | \
                                 POST_SLOWTEST  | \
                                 POST_MANUAL    | \
                                 POST_POWERON   )

there is no need to redundantly bitmask it with POST_MANUAL.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>

post: Remove reference to deleted "lwmon" board from Makefile

POST support for sample lwmon board was removed in commit e5d3078622.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>B

Common: SPL: spl_nand: Fixed debug correct NAND ECC type.

In case of #define DEBUG 1 (fordebugging SPL). A bug in
spl_nand_load_image() will be triggered, because it prints
using hw ecc regardless of soft ecc configurations and
initializations.

Signed-off-by: Ahmed Samir <engkhalil86@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

rpi: BCM2837 and Raspberry Pi 3 32-bit support

The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.

>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.

The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:

enable_uart=1

A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: bcm2835: expand Kconfig target descriptions

This adds an explanation of which Raspberry Pi models each target option
supports.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

rpi: add Raspberry Pi 3 board ID

This allows U-Boot to known the name of the board.

The existing rpi_2_defconfig can operate correctly on the Raspberry Pi 3
in 32-bit mode /if/ you have configured the firmware to use the PL011 UART
as the console UART (the default is the mini UART). This requires two
things:
a) config.txt should contain dtoverlay=pi3-miniuart-bt
b) You should run the following to tell the VC FW to process DT when
booting, and copy u-boot.bin.img (rather than u-boot.bin) to the SD card
as the kernel image:

path/to/kernel/scripts/mkknlimg --dtok u-boot.bin u-boot.bin.img

This works as of firmware.git commit 046effa13ebc "firmware: arm_loader:
emmc clock depends on core clock See:
https://github.com/raspberrypi/firmware/issues/572".

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

rpi: use constant "unknown board" DT filename

To simplify support for new SoCs, just use a constant filename
for the unknown case. In practice this case shouldn't be hit anyway, so
the filename isn't relevant, and certainly doesn't need to differentiate
between SoCs. If a user has an as-yet-unknown board, they can override
this value in the environment anyway.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: bcm2835: move CONFIG_BCM283* to Kconfig

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

doc: clarify openssl-based key and certificate generation process

Add some basic clarification that the dev.key file generated by OpenSSL
contains both the public and private key, and further highlight that
the certificate generated here contains the public key only.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>

doc: fix file extension for flattened image tree blob

Different sections in the document suggest flattened image tree blob
files have a file name extension of .itb. Fix the list of file extensions
to reflect that.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>

README: Specify the full path for README.displaying-bmps

It is clearer to specify the full path to access the
doc/README.displaying-bmps file.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery

MSMC segment Privilege ID is not consistent accross the keystone2 SoCs.
As the first step to ensure complete SoC wide coherency setup, lets
refactor the macros to remove the #if-deffery around the code which
obfuscates which IDs are actually enabled for which SoC.

As a result of this change the PCIe configuration is moved after the
msmc configuration is complete, but that should ideally have no
functional impact.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

smsc95xx: fix operation on 64-bit systems

smsc95xx_read_reg() should calculate sizeof(*data) not sizeof(data) since
data is a pointer, and the value pointed at is being transferred over USB,
not the value of the pointer. This fixes operation of the driver in 64-bit
builds, such as the Raspberry Pi 3.

Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Drop command-processing code when CONFIG_CMDLINE is disabled

Command parsing and processing code is not needed when the command line is
disabled. Remove this code in that case.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

fastboot: allow retrieving fastboot variables from env

Some boards need to expose device specific variable through fastboot
(to adpat the flashing script depending on hardware revision for
example).

Provide a way to expose custom fastboot variables. Note that all
variables meant to be exposed through fastboot should be be prefixed
with 'fastboot.', the variable should not exceed 32 bytes (including
the prefix and the trailing '\0') and the variable content should
fit in the response buffer (60 bytes excluding the 'OKAY' prefix and
the trailing '\0').

Signed-off-by: Rob Herring <rob.herring@linaro.org>
[Boris Brezillon: add a commit message]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Steve Rae <srae@broadcom.com>

arm: clang: Update support slightly

- Move most of the flags required into LLVM_RELFLAGS to test at build
time instead of requiring them to be passed in.
- Update doc/README.clang to reflect this
- Switch to rpi_2 as the example as it's closer to working out of the
box than rpi is.

Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git.denx.de/u-boot-sunxi

sunxi: Reserve ATF memory space on A64

On the A64 we usually boot with ATF running in EL3. ATF as it is available
today resides in the first 16MB of RAM. So we should make sure we reserve
that space in our memory maps.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add Pine64+ support

The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.

This patch adds a defconfig and device tree chunks for it.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add support for Allwinner A64 SoCs

The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.

Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Explicitly cast u32 pointer conversions

Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Depend SPL configs on SUPPORT_SPL

We currently depend SPL config options on specific machine types which doesn't
scale. Fortunately there's already a kconfig variable that tells us whether we
want to build SPL code at all, so just depend them on this.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Move cpu independent code to mach directory

Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.

Move all files that are not really tied to armv7 into a new mach-sunxi
directory.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable USB nodes for H8Homlet v2

This provides the minimal changes to the H8Homlet v2 dts to enable USB
in U-boot. It is not what will be submitted to the kernel.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable USB on Cubietruck Plus

This provides the minimal changes to the Cubietruck Plus dts to enable USB
in U-boot. It is not what will be submitted to the kernel.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add USB and R_PIO nodes to sun8i-a83t.dtsi

This provides the minimal changes to the A83T dtsi to enable USB in
U-boot. It is not what will be submitted to the kernel.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Cubietruck Plus: Enable USB Kconfig options in defconfig

The Cubietruck Plus uses all 3 USB controllers:

  - USB OTG functions are provided by the musb USB OTG controller
  - Onboard SATA is provied by a USB-SATA bridge connected to USB1
  - The USB host ports on the board are provided by an HSIC USB hub

FLDO1 is set to 1.2V for HSIC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: h8_homlet_v2: Enable USB Kconfig options in defconfig

The h8_homlet_v2 has 2 USB host ports, one connected to the OTG
controller, one connected to the EHCI/OHCI pair.

Also provide the card detect pin for MMC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ARM: uniphier: remove CONFIG_ARP_TIMEOUT define

I no longer see the problem claimed in the comment block. Rather,
the 0.5 msec timeout seems too short for some TFTP servers.

Drop the CONFIG_ARM_TIMEOUT to fall back to the 5 sec timeout.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

cosmetic: Fix typos "privide"

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: rename function names ph1_* to uniphier_*

Eliminate the "ph1"_ prefixes from function names because "uniphier_"
describes the SoC familiy better.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: add pin-mux settings for NAND, eMMC, SD of PH1-sLD3

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: enable eMMC on PH1-sLD3 reference board

On PH1-sLD3, eMMC and NAND are assigned to different I/O pins.
Both devices can be enabled at the same time.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: adjust dram_init() and dram_init_banksize() for ARM64

Currently, these functions assume #address-cells and #size-cells are
both one.  Fix them to support 64bit DTB.

Also, I am fixing a buffer overrun bug while I am here.  The array
size of gd->bd->bd_dram is CONFIG_NR_DRAM_BANKS.  The number of
iteration in the loop should be limited by that CONFIG.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: drop unneeded defines related to legacy serial driver

These defined were used for pre-DM ns16550 serial driver. They are
unneeded because UniPhier SoCs now use DM serial.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: dts: uniphier: add NAND pinmux node

This will be used to set up pin-muxing for the NAND controller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: dts: uniphier: add clock-frequency to serial nodes of LD11/LD20

Since no clock driver is implemented for peripherals in U-Boot yet,
this property is needed for the serial driver to set up the divisor
register.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: support UniPhier PH1-LD11 pinctrl driver

The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver

Add pin configuration and pinmux support for UniPhier PH1-LD20 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: support per-pin input enable for new SoCs

Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit prepares the core part for that.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: introduce capability flag

The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs.  This sometimes happens
because pinctrl drivers include really SoC-specific stuff.

This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding new ones.  Having flags would be better than
adding new members every time a new SoC-specific capability comes up.

At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from our customer.  For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

pinctrl: uniphier: use devm_get_addr() to get base address

Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mmc: uniphier: use devm_get_addr() to get base address

Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

gpio: uniphier: use devm_get_addr() to get base address

Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

i2c: uniphier: use devm_get_addr() to get base address

Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

clk: uniphier: use devm_get_addr() to get base address

Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

serial: uniphier: use devm_get_addr() to get base address

Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: add sramupdate command

This command would be useful to update U-Boot images in SRAM.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: make u-boot-with-spl.bin really available

Commit d085ecd61b99 ("ARM: uniphier: switch to raw U-Boot image")
claimed that u-boot-with-spl.bin would be useful in its commit log,
but it was not available because the commit missed to define
CONFIG_SPL_MAX_SIZE. Without it, CONFIG_SPL_PAD_TO is not defined
either (see include/config_fallbacks.h). So, the SPL image is not
padded correctly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

mtd: nand: denali: max_banks calculation changed in revision 5.1

Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.

[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]

Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

sunxi: ohci: Add A83T compatible

We have a separate compatible for almost each SoC. Add one for the A83T.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: ehci: Add A83T compatible

We have a separate compatible for almost each SoC. Add one for the A83T.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: clk: Fix USB PHY clock macros for A83T

The A83T has 3 PHYs, the last one being HSIC, which has 2 clocks.
Also there is only 1 OHCI.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: usb_phy: Add support for A83T USB PHYs

The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: h8_homlet_v2: Set DLDO4 to 3.3V

DLDO4 supplies power to the PD pins, and the AC200 Ethernet PHY /
composite video encoder.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: h8_homlet_v2: Set DCDC1 to default voltage (3.3V)

The schematics of the h8_homlet_v2 show DCDC1 set to 3.3V. Some
Allwinner-based boards set it to 3.0V to conserve power. Since the
h8_homlet_v2 is a set-top box board with external power, there is
no such requirement.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

power: axp818: Add support for FLDOs

The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY
on the A83T/H8.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

power: axp818: Fix DCDC5 default voltage

DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3,
1.35V for DDR3L, and 1.2V for LPDDR3.

Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: axp: Support VBUS drive GPIO on AXP818

AXP818 supports VBUS drive function, even though the manual does not
mention it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: axp: Generalize register macros for VBUS drive GPIO

VBUS drive is supported on AXP221 and later PMICs. Rework the macros
so we can support this on later PMICs without too much work.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

musb: sunxi: Add support for A83T

Like the Allwinner A33 SoC, the A83T is missing the config register
from the musb USB DRD hardware block. Use a known working value for
it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

power: axp818: Remove undefined axp818_init()

axp818_init() is declared, but never defined.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Enable LDO3 and LDO4 at 2.8V on OLinuxIno Lime boards

LDO3 and LDO4 are used to power port E resp. port G, which are exposed
on gpio headers, so enable them at 2.8V as specified in the schematic.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: A20-OLinuXino-Lime2: Force 8211CL to master

Force master mode on the A20-OLinuXino-Lime2. This change is required
to get a reliable link at gigabit speeds.

Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: A20-Olimex-SOM-EVB: Force 8211CL to master

Force master mode for 1000BASE-T operation on the
A20-Olimex-SOM-EVB.

Karsten Merker reports that this change is necessary to get a reliable
link at gigabit speeds.

Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

net: phy: Optionally force master mode for RTL PHY

This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.

This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.

There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.

CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Print soc-id from sram controller for sun8i boards

As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

sunxi: Add conditional magic sram poke for A33

I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Merge branch 'master' of git://git.denx.de/u-boot-tegra

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

ARM: tegra210: set PLLE_PTS bit when enabling PLLE

This bit needs to be set for system suspend/resume to work. This setting
will be documented in an updated TRM at some time in the future.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

armv8/ls2080ardb: Enable VID support

This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.

Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8/ls1043aqds: dts: Set SPI mode for DSPI

Clock phase and polarity for DSPI flash need to be set.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Add LS1023A SVR

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Fix LS1043A SVR register

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

SECURE BOOT: Change fsl_secboot_validate func to pass image addr

Use a pointer to pass image address to fsl_secboot_validate(),
instead of using environmental variable "img_addr".

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

SECURE BOOT: Halt execution when secure boot fail

In case of fatal failure during secure boot execution (e.g. header
not found), reset is asserted to stop execution. If the RESET_REQ
is not tied to HRESET, this allows the execution to continue.

Add esbh_halt() after the reset to make sure execution stops.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

SECURE_BOOT: Use default bootargs

For secure boot, currently we were using fixed bootargs for all SoCs.
This is not needed and we can use the bootargs which are used in
non-secure boot.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

crypto/fsl: Make CAAM transactions cacheable

This commit solves CAAM coherency issue on ls2080. When caches are
enabled and CAAM's DMA's AXI transcations are not made cacheable,
Core reads/writes data from/to caches and CAAM does from main memory.
This forces data flushes to synchronize various data structures. But
even if any data in proximity of these structures is read by core,
these structures again are fetched in caches.

To avoid this problem, either all the data that CAAM accesses can be
made cache line aligned or CAAM transcations can be made cacheable.

So, this commit makes CAAM transcations as write back with write and
read allocate.

Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

crypto/fsl: Correct 64-bit write when MMU disabled

When MMU is disabled, 64-bit write must be aligned at 64-bit
boundary. Becaue the memory location is not guaranteed to be 64-bit
aligned, the 64-bit write needs to be split into two 32-bit writes
to avoid the alignment exception.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-lsch3: Disable SMMU during secure boot

During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs
to be put in bypass mode in uboot to enable CAAM transcations to pass
through.

For non-secure boot, SP BootROM doesn't enable SMMU, which is in
bypass mode out of reset.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls2080: Add config for endianess of CCSR GUR

The GUR (DCFG) registers in CCSR space are in little endian format.
Define a config CONFIG_SYS_FSL_CCSR_GUR_LE in
arch/arm/include/asm/arch-fsl-layerscape/config.h

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls2080: Change env variable "fdt_high"

"fdt_high" env variable was set to 0xcfffffff for secure boot.
Change it to 0xa0000000 for LS2080 to be consistent with non-secure
boot targets.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-lsch3: Copy Bootscript and header from NOR to DDR

To unify steps for secure boot for xip (eg. NOR) and non-xip memories
(eg. NAND, SD), bootscipts and its header are copied to main memory.
Validation and execution are performed from there.

For other ARM Platforms (ls1043 and ls1020), to avoid disruption of
existing users, this copy step is not used for NOR boot.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls2080: Add bootscript header addr for secure boot

During secure boot, Linux image along with other images are validated
using bootscript. This bootscript also needs to be validated before
it executes. This requires a header for bootscript.

When secure boot is enabled, default bootcmd is changed to first
validate bootscript using the header and then execute the script.

For ls2080, NOR memory map is different from other ARM SoCs. So a new
address on NOR is used for this bootscript header (0x583920000). The
Bootscript address is mentioned in this header along with addresses of
other images.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls2080rdb: ls2080qds: Add secure boot support

Sec_init has been called at the beginning to initialize SEC Block
(CAAM) which is used by secure boot validation later for both ls2080a
qds and rdb. 64-bit address in ESBC Header has been enabled. Secure
boot defconfigs are created for boards (NOR boot).

Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-lsch3: Add new header for secure boot

For secure boot, a header is used to identify key table, signature
and image address. A new header structure is added for lsch3.

Currently key extension (IE) feature is not supported. Single key
feature is not supported. Keys must be in table format. Hence, SRK
(key table) must be present. Max key number has increase from 4 to
8. The 8th key is irrevocable. A new barker Code is used.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls2080: Add configs for SEC, SecMon, SRK and DCFG

Add configs for various IPs used during secure boot. Add address
and endianness for SEC and Security Monitor. SRK are fuses in SFP
(fuses for public key's hash). These are stored in little endian
format.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls2080: Add SFP Configs for LS2080

In LS2080, SFP has version 3.4. It is in little endian. The base
address is 0x01e80200. SFP is used in Secure Boot to read fuses.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver: net: fsl-mc: Check NULL before pointer dereference

NULL pointer should be checked before any dereference. This patch
move memest after the NULL pointer check.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>

driver: net: fsl-mc: Free dflt_dpio pointer after its usage

Free dflt_dpio pointer after its usage during error handling

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Skip reconfigure QSPI clock when booting from QSPI

The qspi_cfg register is set by PBI when booting from QSPI. No need
to changing it again.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

omap24xx_i2c: Implement CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW

Signed-off-by: Guy Thouret <guy.thouret@wems.co.uk>
Cc: Heiko Schocher <hs@denx.de>

dm: i2c: mxc_i2c: implement i2c_idle_bus

Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c

This patch is an implementation following linux kernel patch:
"
commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date:   Fri Oct 23 20:28:54 2015 +0800

    i2c: imx: implement bus recovery

    Implement bus recovery methods for i2c-imx so we can recover from
    situations where SCL/SDA are stuck low.

    Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
    pinctrl to gpio mode by calling pinctrl sleep set function, and then
    use GPIO to emulate the i2c protocol to send nine dummy clock to recover
    i2c device. After recovery, set i2c pinctrl to default group setting.
"

See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
   since we have pinctrl driver/driver model gpio driver. We can
   use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
   there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
   be used, so when need to use gpio function, need to do
   "pinctrl_select_state(dev, "gpio")" and after force bus idle,
   need to switch back "pinctrl_select_state(dev, "default")".

This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};

[.....]

pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>

Revert "pxa_lcd: make driver cache-aware"

This reverts commit 59deb7fe8d23c8ec2b659d99323ec4a2ec19148a.

Signed-off-by: Tom Rini <trini@konsulko.com>

Revert "pxa_lcd: invert colors for Zipit Z2 to get white on black palette"

This reverts commit 3bc8ffd9cb774feceefc7bdebe9353fcea071343.

Signed-off-by: Tom Rini <trini@konsulko.com>

tools: env: bug: config structs must be defined in tools library

fw_senten/fw_printenv can be compiled as a tools library,
excluding the fw_env_main object.

Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>

ARM: asm: types: Introduce DMA_ADDR_T_64BIT

dma_addr_t holds any valid DMA address. If the DMA API only uses 32-bit
addresses, dma_addr_t need only be 32 bits wide. Bus addresses, e.g., PCI BARs,
may be wider than 32 bits, but drivers do memory-mapped I/O to ioremapped
kernel virtual addresses, so they don't care about the size of the actual
bus addresses.
Also 32 bit ARM systems with LPAE enabled can use 64bit address space, but
DMA still use 32bit address like in case of DRA7 and Keystone platforms.

This is inspired from the Linux kernel types implementation[1]

[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/include/linux/types.h#n142

Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>