John Crispin [Sat, 16 Nov 2013 20:20:30 +0000 (20:20 +0000)]
procd: ubox: update to latest git head
move log service from procd to ubox
some debloating on procd
the preinit part of procd is now also a seperate binary
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38822
Zoltan Herpai [Sat, 16 Nov 2013 11:52:30 +0000 (11:52 +0000)]
kernel: add missing symbols for 3.12
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38820
Luka Perkov [Sat, 16 Nov 2013 10:17:38 +0000 (10:17 +0000)]
sunxi: remove old kernel config after 3.12 upgrade (r38811)
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38819
Steven Barth [Sat, 16 Nov 2013 09:18:14 +0000 (09:18 +0000)]
6rd: Clear correct IPv6 address bits in 6rdcalc
The correct bits are now cleared in the IPv6 address as the shift
value to the correct byte in the IPv6 address was wrong. Depending
on the stack values this could result in a hanging 6rdcalc program
due to an endless loop.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 38818
Imre Kaloz [Fri, 15 Nov 2013 12:23:17 +0000 (12:23 +0000)]
replace the TI patch with a smaller patchset
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 38816
Gabor Juhos [Fri, 15 Nov 2013 10:11:25 +0000 (10:11 +0000)]
ar71xx: add profile for the WR842N/ND v2
Patch to add the profile for the TP-LINK WR842N/ND v2
Small update, because of a change in the Makefile.
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4382/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38815
Gabor Juhos [Fri, 15 Nov 2013 10:11:24 +0000 (10:11 +0000)]
ar71xx: add user space support for the TL-WR842N/ND v2
Patch to add the user space support for the TL-WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38814
Gabor Juhos [Fri, 15 Nov 2013 10:11:20 +0000 (10:11 +0000)]
ar71xx: Add kernel support for the WR842N/ND v2
Patch to add kernel support for the TP-LINK WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4352/
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38813
Gabor Juhos [Fri, 15 Nov 2013 08:21:59 +0000 (08:21 +0000)]
ar71xx: wndr4300: set official mac addresses
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
- move WiFi MAC address setup to the firmware hotplug file,
- use the official MAC address for the 2.4GHz as well,
- remove uci-defaults.sh modifications,
- update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38812
Zoltan Herpai [Thu, 14 Nov 2013 23:12:52 +0000 (23:12 +0000)]
sunxi: rework target - update kernel to 3.12 - add patches for clocks, i2c, usb, sid, rtc - support common image for A10/A13/A20 - add support for a couple boards - most drivers are configured into the kernel as of now
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38811
Felix Fietkau [Thu, 14 Nov 2013 22:01:24 +0000 (22:01 +0000)]
kernel: backport an upstream fix to improve TCP performance for wifi drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38810
Felix Fietkau [Thu, 14 Nov 2013 20:42:15 +0000 (20:42 +0000)]
openssl: add support for RIPEMD/160
RIPEMD is needed to update erlang and i'd like to enable RIPEMD160 support in openssh.
Size compared:
openssl without RIPEMD/160 support:
647K 29. Okt 20:00 bin/ar71xx/packages/libopenssl_1.0.1e-2_ar71xx.ipk
openssl with RIPEMD/160 support:
652K 8. Nov 15:11 bin/ar71xx/packages/libopenssl_1.0.1e-2_ar71xx.ipk
So the file size just grows ~5kb, which shouldn't be a problem.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 38809
Felix Fietkau [Thu, 14 Nov 2013 20:32:36 +0000 (20:32 +0000)]
rt2x00: fix a crash in the recent update (#14467)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38808
Felix Fietkau [Thu, 14 Nov 2013 19:38:54 +0000 (19:38 +0000)]
ar71xx: Unifi AP Pro sysupgrade patch
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.
To fix this problem, a new option
-s <number> skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"
is added to mtd.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 38807
Felix Fietkau [Thu, 14 Nov 2013 19:16:04 +0000 (19:16 +0000)]
ramips: use dd bs=4096k instead of bs=4M to make it more portable
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38806
Felix Fietkau [Thu, 14 Nov 2013 19:04:48 +0000 (19:04 +0000)]
ar71xx: use the new padjffs2 padding on Ubiquiti UAP-PRO to make the boot loader stop searching after the kernel partition
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38805
Felix Fietkau [Thu, 14 Nov 2013 19:04:44 +0000 (19:04 +0000)]
padjffs2: add a different kind of padding (using standard jffs2 elements) to work around broken boot loaders for kernel partitions
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38804
Gabor Juhos [Thu, 14 Nov 2013 17:44:42 +0000 (17:44 +0000)]
base-files: add macaddr_canonicalize helper function
In commit r38690, the MAC address canonicalization
has been converted to use 'tr' instead of 'printf'.
This only works if with MAC addresses which uses
the 'xx:xx:xx:xx:xx:xx' format.
However on some boards, the MAC addresses are stored
in different format in the mtd partition. Some vendors
are using hyphens or dots as separators instead of
colons. Also the leading zeroes may be missing from the
individual octets or those are replaced with spaces.
Add a new function which can be used to convert these
into the 'xx:xx:xx:xx:xx:xx' format. Also update the
'mtd_get_mac_ascii' function to use the new helper.
The helper function is based on this code:
http://isquared.nl/blog/2010/08/11/Bash-function-to-canonicalize-MAC-addresses/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38803
Felix Fietkau [Thu, 14 Nov 2013 12:21:24 +0000 (12:21 +0000)]
ath9k: add a fix to improve reliability of high bitrates on AR93xx/AR95xx
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38802
Felix Fietkau [Thu, 14 Nov 2013 12:21:19 +0000 (12:21 +0000)]
mac80211: merge a patch that enables DFS for ad-hoc mode
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38801
Luka Perkov [Thu, 14 Nov 2013 01:35:22 +0000 (01:35 +0000)]
Config.in: drop TARGET_UBIFS_SQUASH_UIDS, it's used by default now
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38800
Luka Perkov [Thu, 14 Nov 2013 01:35:21 +0000 (01:35 +0000)]
image: don't force ubifs journal size
Small journal size can lead to problems if nand flash is too big. By default
ubifs will use ~12% of volume size or a maximum of 8MiB.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38799
Hauke Mehrtens [Wed, 13 Nov 2013 22:36:12 +0000 (22:36 +0000)]
mac80211: update regdb.txt
This was copied from wireless-regdb.git commit
a14052b85e5d70e37a31962a9c56c0cdbb9acafc
The passive-scan/no-ibss flag of channels 36-48 in the world regd were
removed like it was done in r32126.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38797
Hauke Mehrtens [Wed, 13 Nov 2013 22:26:08 +0000 (22:26 +0000)]
bcm53xx: this ARM SoC does not have a FPU, use soft float.
model name : ARMv7 Processor rev 0 (v7l)
Features : swp half thumb fastmult edsp tls
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38796
Hauke Mehrtens [Wed, 13 Nov 2013 18:42:45 +0000 (18:42 +0000)]
zram-swap: fix dependencies
swapon/swapoff are no longer provided by swap-utils; they are provided
by block-mount instead.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38795
Hauke Mehrtens [Wed, 13 Nov 2013 18:38:18 +0000 (18:38 +0000)]
brcm47xx: swap also early boot console if necessary.
Some devices are using tty1 as the default console, also swap the early
boot console in such case. This is needed for the WGT634U.
Thank you Russell for reporting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38794
Hauke Mehrtens [Wed, 13 Nov 2013 18:04:39 +0000 (18:04 +0000)]
kernel: b53: fix untagged shift for BCM5365
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38793
Imre Kaloz [Wed, 13 Nov 2013 14:47:31 +0000 (14:47 +0000)]
upgrade linux-firmware git revision, bump package version
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 38792
Imre Kaloz [Wed, 13 Nov 2013 14:46:21 +0000 (14:46 +0000)]
add another symbol for TI chipsets
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 38791
John Crispin [Wed, 13 Nov 2013 12:15:06 +0000 (12:15 +0000)]
procd: remove obselete script install reference Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38790
John Crispin [Wed, 13 Nov 2013 11:07:24 +0000 (11:07 +0000)]
procd: fixup 2 wrong option types
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38789
John Crispin [Wed, 13 Nov 2013 10:57:16 +0000 (10:57 +0000)]
procd: options with default values are not parsed properly in the ubus register code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38788
John Crispin [Wed, 13 Nov 2013 10:49:41 +0000 (10:49 +0000)]
procd: convert services to the new validation api
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38787
John Crispin [Wed, 13 Nov 2013 10:49:25 +0000 (10:49 +0000)]
procd: update to latest git head
this includes the first wip version of the uci validation backend
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38786
Zoltan Herpai [Wed, 13 Nov 2013 10:49:22 +0000 (10:49 +0000)]
uboot-sunxi: add U-boot builds for a couple sunxi boards
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38785
Felix Fietkau [Wed, 13 Nov 2013 10:29:10 +0000 (10:29 +0000)]
ramips: select kmod-rt2800-soc by default (if available)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38784
Felix Fietkau [Tue, 12 Nov 2013 22:11:33 +0000 (22:11 +0000)]
mac80211: update to wireless-testing 2013-11-05
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38783
Felix Fietkau [Tue, 12 Nov 2013 22:11:14 +0000 (22:11 +0000)]
hostapd: remove #ifdef MULTICALL around ap+sta support code (to support separately installed supplicant+hostapd)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38782
Zoltan Herpai [Tue, 12 Nov 2013 14:39:32 +0000 (14:39 +0000)]
mxs: - update uboot-mxs to 3.10 - enable building uboot for imx23 along sbImage by default - (doc updated)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38781
Zoltan Herpai [Tue, 12 Nov 2013 12:48:10 +0000 (12:48 +0000)]
mxs: bump kernel to 3.12 - remove DCP patch as it's in mainline now (dts patch will stay) - refresh Duckbill patch - update kmod-usb-chipidea
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38780
Jo-Philipp Wich [Tue, 12 Nov 2013 11:01:11 +0000 (11:01 +0000)]
Add patch to fix ipset timeout setting problem
Fixes #14325
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 38779
Jo-Philipp Wich [Tue, 12 Nov 2013 11:00:49 +0000 (11:00 +0000)]
Update ipset to version 6.20.1
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 38778
Zoltan Herpai [Tue, 12 Nov 2013 10:19:26 +0000 (10:19 +0000)]
mxs: add basic board runtime detection support
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38777
Zoltan Herpai [Tue, 12 Nov 2013 10:07:03 +0000 (10:07 +0000)]
uboot-envtools: add support for mxs target
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 38776
Zoltan Herpai [Tue, 12 Nov 2013 09:38:14 +0000 (09:38 +0000)]
mxs: duckbill: adjust leds to final hardware
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 38775
Zoltan Herpai [Tue, 12 Nov 2013 01:34:30 +0000 (01:34 +0000)]
mxs: rename uboot-imx23 to uboot-mxs
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38774
Zoltan Herpai [Tue, 12 Nov 2013 01:25:53 +0000 (01:25 +0000)]
mxs: fix loadaddr for uImages
Signed-off-by: Harald Geyer <harald@ccbib.org>
SVN-Revision: 38773
Zoltan Herpai [Tue, 12 Nov 2013 01:09:15 +0000 (01:09 +0000)]
kernel: add new core sound module snd-pcm-dmaengine.ko for 3.12 kernels and above
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38772
Luka Perkov [Mon, 11 Nov 2013 23:34:11 +0000 (23:34 +0000)]
base-files: don't enter failsafe if triggered by switch
Fixes failsafe issues with switches after r38725.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38770
Hauke Mehrtens [Mon, 11 Nov 2013 23:04:47 +0000 (23:04 +0000)]
brcm47xx: fix netconfig for inverted vlan?ports in nvram
This was observed on the Belkin Share
F7D7302.
SVN-Revision: 38769
Hauke Mehrtens [Mon, 11 Nov 2013 23:04:23 +0000 (23:04 +0000)]
broadcom-diag: add Belkin
F7D3302/
F7D7302
Signed-off-by: Cody P Schafer <devel@codyps.com>
SVN-Revision: 38768
Hauke Mehrtens [Mon, 11 Nov 2013 23:04:00 +0000 (23:04 +0000)]
linux/brcm47xx : Belkin F7Dx30x board detection
boardnum is unstable, so allow using NULL to make it unchecked.
A method for differentiating
F7D3301 from
F7D3302 using nvram is
unknown at this point. Reading the first 32bits of magic from the
"linux" mtd partition would do the trick, but these 2 are similar
enough that we don't need separate led/button definitions. Not knowing
which one you have is only a usability issue for upgrading the device:
they expect different magic numbers for their trx images.
Signed-off-by: Cody P Schafer <devel@codyps.com>
SVN-Revision: 38767
Hauke Mehrtens [Mon, 11 Nov 2013 22:12:58 +0000 (22:12 +0000)]
base-files: don't kill nas for sysupgrade
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38766
Hauke Mehrtens [Mon, 11 Nov 2013 22:05:39 +0000 (22:05 +0000)]
broadcom-wl: version roll
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38765
Hauke Mehrtens [Mon, 11 Nov 2013 22:05:20 +0000 (22:05 +0000)]
broadcom-wl: support 'wds' interfaces on 'wl1' device
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38764
Hauke Mehrtens [Mon, 11 Nov 2013 22:04:53 +0000 (22:04 +0000)]
broadcom-wl: support probe of 'wds' devices
'nas' requires probe of 'wds' devices to be successful;
so don't fail them.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38763
Hauke Mehrtens [Mon, 11 Nov 2013 22:04:26 +0000 (22:04 +0000)]
broadcom-wl: fix crash when starting multiple virtual interfaces
When enabling multiple VIFS, the driver sometimes crashes. The frequency
of the crash increases as more VIFS are enabled.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38762
Hauke Mehrtens [Mon, 11 Nov 2013 22:03:58 +0000 (22:03 +0000)]
broadcom-wl: perform additional cleanup on wl module unload
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38761
Zoltan Herpai [Mon, 11 Nov 2013 22:03:35 +0000 (22:03 +0000)]
kernel: of_i2c is moved into i2c-core in 3.12, add kernel version check into modules/i2c.mk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 38760
Hauke Mehrtens [Mon, 11 Nov 2013 22:03:25 +0000 (22:03 +0000)]
broadcom-wl: support more virtual interfaces
Read the number of virtual interfaces to support from the device
capabilities; as some newer devices can support up to 16.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38759
Hauke Mehrtens [Mon, 11 Nov 2013 22:02:45 +0000 (22:02 +0000)]
broadcom-wl: improve device cleanup
Move all device cleanup to "disable_broadcom".
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38758
Hauke Mehrtens [Mon, 11 Nov 2013 22:02:14 +0000 (22:02 +0000)]
broadcom-wl: add support for setting H/W address
Some devices initialize with a default address (common to all H/W).
The address needs to be changeable so that a unique address can be
assigned to each AP.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38757
Hauke Mehrtens [Mon, 11 Nov 2013 22:01:32 +0000 (22:01 +0000)]
broadcom-wl: eliminate 'invalid command' when setting ssid
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38756
Hauke Mehrtens [Mon, 11 Nov 2013 22:01:12 +0000 (22:01 +0000)]
broadcom-wl: clean up variable definitions (broadcom.sh)
Specify variables as 'local' where appropriate
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38755
Hauke Mehrtens [Mon, 11 Nov 2013 22:00:39 +0000 (22:00 +0000)]
broadcom-wl: simplify processing of 'hwmode'
Default gmode to "GOnly" unless explicitly overwridden. This corrects
processing for 11ng to specify "GOnly" for gmode instead of "Auto"
(which translated to "bg").
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38754
Hauke Mehrtens [Mon, 11 Nov 2013 21:59:58 +0000 (21:59 +0000)]
broadcom-wl: shutdown 'nas' when 'wl' device is disabled
'nas' must be shutdown independently for each 'wl' device to properly
support devices with multiple radios. Do the shutdown when the device
is disabled instead of when it is brought up.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38753
Hauke Mehrtens [Mon, 11 Nov 2013 21:59:34 +0000 (21:59 +0000)]
broadcom-wl: use a single instance of 'nas' per 'wl' device
A single instance of 'nas' can support multiple interfaces; there's
no need to run multiple instances.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38752
Hauke Mehrtens [Mon, 11 Nov 2013 21:59:07 +0000 (21:59 +0000)]
broadcom-wl: fix whitespace handling
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38751
Hauke Mehrtens [Mon, 11 Nov 2013 21:58:42 +0000 (21:58 +0000)]
broadcom-wl: update description for recently added
Update descriptions for 'phytype' and 'band'.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38750
Hauke Mehrtens [Mon, 11 Nov 2013 21:58:19 +0000 (21:58 +0000)]
broadcom-wl: fix band reporting
Modify the band reporting for broadcom devices to correctly report
HW capability. Currently, 802.11na devices report "bgn"; but should be
reporting "an".
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38749
Hauke Mehrtens [Mon, 11 Nov 2013 21:57:26 +0000 (21:57 +0000)]
broadcom-wl: change interface names
'netifd' treats all devices with a "." in their name as vlan devices.
Modify the name of virtual/WDS interfaces created by broadcom-wl to use
a "-" instead of a ".", so they will be treated as simple devices
by 'netifd'.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38748
Hauke Mehrtens [Mon, 11 Nov 2013 21:56:45 +0000 (21:56 +0000)]
broadcom-wl: fix compiler warning
Delete the return value (nvram_exit is declared with a 'void' return).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38747
Hauke Mehrtens [Mon, 11 Nov 2013 21:54:55 +0000 (21:54 +0000)]
iwinfo: don't report associations for broadcom wds interfaces
The associations list for Broadcom WDS interfaces are duplicate to those
reported by the corresponding AP interface; so there is no need to report
them again.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38746
Hauke Mehrtens [Mon, 11 Nov 2013 21:54:25 +0000 (21:54 +0000)]
iwinfo: fix hwmodelist reporting for broadcom wl
Modify the hwmodelist reporting for broadcom devices to include
proper reporting of 802.11n support.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38745
Hauke Mehrtens [Mon, 11 Nov 2013 21:23:29 +0000 (21:23 +0000)]
brcm47xx: b44: fix logic in BUG_ON()
It is a problem when phydev is not set at this position and not the other way around.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38744
Jo-Philipp Wich [Mon, 11 Nov 2013 19:14:01 +0000 (19:14 +0000)]
uhttpd: return after processing -d switch, only set ubus prefix if not already defined
SVN-Revision: 38743
John Crispin [Mon, 11 Nov 2013 18:12:30 +0000 (18:12 +0000)]
base-files: fix typo in rfkill script
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38742
John Crispin [Mon, 11 Nov 2013 18:12:26 +0000 (18:12 +0000)]
uhttp: add ubus.default
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38741
Felix Fietkau [Mon, 11 Nov 2013 16:51:01 +0000 (16:51 +0000)]
ixp4xx: fix usb on cambria boards by using the ehci-platform driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38740
John Crispin [Mon, 11 Nov 2013 13:40:28 +0000 (13:40 +0000)]
pppd: don't call modprobe at all from pppoatm
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38737
John Crispin [Mon, 11 Nov 2013 13:40:24 +0000 (13:40 +0000)]
revert
94e44643a8ce1d7991376b6ced586784b3f92500
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38736
John Crispin [Mon, 11 Nov 2013 13:40:20 +0000 (13:40 +0000)]
ramips: use gpio-button-hotplug in favour of the input variant
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38735
John Crispin [Mon, 11 Nov 2013 13:40:17 +0000 (13:40 +0000)]
ramips: make the rfkill switch work on fonera20n
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38734
John Crispin [Mon, 11 Nov 2013 13:15:08 +0000 (13:15 +0000)]
lantiq: DGN3500 fixups
Just fixing up a few things for the Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 38733
John Crispin [Mon, 11 Nov 2013 13:15:04 +0000 (13:15 +0000)]
Fix modprobe path for pppoatm
Without netifd generates an error:
daemon.notice netifd: wan (1249): /bin/sh: /sbin/modprobe: not found
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 38732
John Crispin [Mon, 11 Nov 2013 12:22:12 +0000 (12:22 +0000)]
lantiq: dont install deu test manager
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38731
John Crispin [Mon, 11 Nov 2013 12:19:26 +0000 (12:19 +0000)]
lantiq: rename TDW8970 led adsl->dsl
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38730
John Crispin [Mon, 11 Nov 2013 12:19:22 +0000 (12:19 +0000)]
base-files: update rfkill script to work with slider buttons
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38729
John Crispin [Mon, 11 Nov 2013 12:19:18 +0000 (12:19 +0000)]
lantiq: update TDW8970.dts to support buttons properly
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38728
John Crispin [Mon, 11 Nov 2013 12:19:15 +0000 (12:19 +0000)]
lantiq: remove old hotplug handler
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38727
John Crispin [Mon, 11 Nov 2013 12:19:10 +0000 (12:19 +0000)]
base-files: add a generic wps button handler
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38726
John Crispin [Mon, 11 Nov 2013 12:19:06 +0000 (12:19 +0000)]
gpio-button-hotplug: add support for sliding switches
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38725
John Crispin [Mon, 11 Nov 2013 12:19:02 +0000 (12:19 +0000)]
uhttp: make the service auto respawn if it crashes
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38724
John Crispin [Mon, 11 Nov 2013 12:18:58 +0000 (12:18 +0000)]
uhttp: make sure that the ubus module is loaded when when installed
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38723
Imre Kaloz [Mon, 11 Nov 2013 11:55:44 +0000 (11:55 +0000)]
add missing option, enable hw rng
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 38722
Imre Kaloz [Mon, 11 Nov 2013 11:51:54 +0000 (11:51 +0000)]
depend on the correct target
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 38721
Gabor Juhos [Mon, 11 Nov 2013 08:10:02 +0000 (08:10 +0000)]
ar71xx: Use KEY_RESTART key code for the reset button on WD My Net N600 boards
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38720
Gabor Juhos [Mon, 11 Nov 2013 08:04:48 +0000 (08:04 +0000)]
ar71xx: add profile and build image for the TL-WA750RE TL-WA850RE range extender
Patch to add profile and build image for the tplink TL-WA750RE/WA850RE board
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38719
Gabor Juhos [Mon, 11 Nov 2013 08:04:47 +0000 (08:04 +0000)]
ar71xx: add user space support for the TL-WA750RE/WA850RE Range extender
Patch to add user space support for the TL-WA750RE/WA850RE range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38718
Gabor Juhos [Mon, 11 Nov 2013 08:04:46 +0000 (08:04 +0000)]
ar71xx: Add kernel support for the TP-Link WA750RE / WA850RE range extender
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38717
projects / oweals / openwrt.git / log