video: indicate code page of bitmap fonts

Add comments clarifying that the bitmap fonts support code page 437.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

pwm-backlight: make power-supply as option

Some pwm backlight may not need 'power-supply', let's make it as option
in pwm-backlight driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

dm: video: support increased intensity (bold)

Support special rendition code 0 - reset attributes.
Support special rendition code 1 - increased intensity (bold).

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

dm: video: use constants to refer to colors

Use constants to refer to colors.
Adjust initialization of foreground and background color to avoid
setting reserved bits.
Consistently u32 instead of unsigned for color bit mask.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

dm: video: correctly clean background in 16bit mode

In 16 bit mode we have to copy two bytes per pixels repeatedly and not
four. Otherwise we will see a striped pattern.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

dm: video: show correct colors in graphical console

Get RGB sequence in pixels right (swap blue and red).
Do not set reserved bits.

qemu-system-i386 -display sdl -vga virtio and
qemu-system-i386 -display sdl -vga cirrus
now display the similar colors (highlighting still missing) as
qemu-system-i386 -nographic

Testing is possible via

setenv efi_selftest test output
bootefi selftest

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

Prepare v2018.03-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-sh

Devboards.de DBM-SoC1 BOARD: Add S line

This was missing the 'S' line causing a warning from genboardscfg.py

Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: DTS: Re-sync logicpd-som-lv with Linux 4.16-rc3

This should clean up a warning about a missing phy-cells

Signed-off-by: Adam Ford <aford173@gmail.com>

MAINTAINERS: bring sections into alphabetic order

POWER should be after ONENAND

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

scripts/spelling.txt: Sync script with kernel 4.16-rc4

Keep spelling.txt in sync with the version from kernel 4.16-rc4.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

omap3_logic: Remove unnecessary undefs

Due to evolution of the MMC driver and better support, let's
remove unnecessary undefs.

Signed-off-by: Adam Ford <aford173@gmail.com>

ti_armv7_omap: Remove comment remnant

With the migration to Kconfig, the I2C block no longer exists in here.
Let's clean up the comment.

Signed-off-by: Adam Ford <aford173@gmail.com>

MPC8315ERDB: Enable DHCP support

Enable DHCP support for this board.

Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>

Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

tools: Include U-Boot libfdt headers from their actual path

There are no headers for libfdt in lib/libfdt, as they are instead
located in scripts/dtc/libfdt. Specifying lib/libfdt for headers
inclusion in host tools results in using the system libfdt headers,
which is not what we want. Change this to the proper path.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>

input: indicate that code page 437 is used

Add a comment indicating that the German key map assumes code page 437.

Add support for character ² (square sign) in the German key map.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

pinctrl: Kconfig: Fix typo

Signed-off-by: Marek Behun <marek.behun@nic.cz>

gpio: pca953x_gpio: Support label setting from DT

The PCA953x driver uses "gpio@%x_" as the GPIO bank name, where "%x" is
instantiated with the I2C address of the chip. While this works, it
becomes very confusing if a board has multiple PCAs with the same
address on different I2C busses, and it also becomes an issue when a
GPIO's value is to be set via the 'gpio' command, because this command
only ever sets the value of the first device it encounters, leaving the
other devices inaccessible to the command.

As to not break boards that rely on this naming scheme, we introduce a
new device tree string property "label" for the driver. If it exists, it
is used to build a bank name of the form "%s@%x_" (where %x is still
instantiated with the I2C address). If it does not exist, the legacy
labeling scheme is used.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the U-boot CONFIG

Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.

This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

tools/env: allow equal sign as key value separation

Treat the first equal sign as a key/value separation too. This makes
the script files compatible with mkenvimage input file format. It
won't support variables with equal signs anymore, but this seems not
really like a loss.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

Atmel TPM: Fix potential buffer overruns

Ensure that the Atmel TPM driver performs sufficient
validation of the length returned in the TPM response header.
This patch prevents memory corruption if the header contains a
length value that is larger than the destination buffer.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>

Infineon TPM: Fix potential buffer overruns

Ensure that the Infineon I2C and SPI TPM driver performs adequate
validation of the length extracted from the TPM response header.
This patch prevents integer underflow when the length was too small,
which could lead to memory corruption.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>

STMicro TPM: Fix potential buffer overruns

This patch prevents integer underflow when the length was too small,
which could lead to memory corruption.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>

ARM: dts: rmobile: Add PHY reset GPIO

This patch got dropped during the update of DTs to 4.14, re-add it
back. This adds reset GPIOs to the ethernet PHYs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: dts: rmobile: Make PFC and RST available early on Gen2 only

These do not need to be available early on Gen3 , so move them to
the respective DT files.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Add R8A77965 Salvator-XS board support

Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: dts: rmobile: Add SDHI nodes to R8A77965 M3N DT

Add SDHI nodes to r8a77965.dtsi to get eMMC and SD slots operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: dts: rmobile: Add xHCI node to R8A77965 M3N DT

Add xHCI node to r8a77965.dtsi to get xHCI USB operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: dts: rmobile: Add EHCI nodes to R8A77965 M3N DT

Add generic EHCI nodes to r8a77965.dtsi to get EHCI USB operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: dts: rmobile: Add RAVB node to R8A77965 M3N DT

Add RAVB node to r8a77965.dtsi to get ethernet operational.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: dts: rmobile: Import R8A77965 M3N DT files from Linux

Import the R8A77965 M3N DT from Linux 4.16-rc1 .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

usb: xhci-rcar: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

pinctrl: rmobile: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

net: ravb: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>

mmc: uniphier-sd: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

gpio: rcar: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

clk: renesas: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Add R8A77965 M3N IDs

Add CPU and PRR IDs for R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

Merge branch 'master' of git://git.denx.de/u-boot-sh

Merge tag 'xilinx-kconfig-for-v2018.03' of git://denx.de/git/u-boot-microblaze

Xilinx Kconfig changes for v2018.03

- Moving some macros to Kconfig

# gpg: Signature made Thu 01 Mar 2018 10:45:58 AM EST using DSA key ID 294A0C21
# gpg: Good signature from "Michal Simek <monstr@monstr.eu>"
# gpg:                 aka "Michal Simek (Xilinx) <michals@xilinx.com>"
# gpg:                 aka "Michal Simek (Xilinx) <michal.simek@xilinx.com>"

mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ

This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ

This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Added Kconfig support for CONFIG_XILINX_GPIO

This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1

This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and
CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET

This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfig

This patch enabled CONFIG_SYS_I2C_ZYNQ in the respective
defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPL

This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the
values over to the defconfigs.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

fpga: Added Kconfig support for FPGA_SPARTAN3

This patch added Kconfig support for FPGA_SPARTAN3 and migrates the
values over to the defconfigs.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

Merge git://git.denx.de/u-boot-net

Kconfig: cmd: Make networking command dependent on NET

Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Makefile: add u-boot-spl.srec target

The u-boot-spl.srec is needed for some platforms, add target to generate this file.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-elf.srec on Gen3

The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs,
conveniently generate this file.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Makefile: add u-boot-elf.srec target

The u-boot-elf.srec is needed for some platforms, add target to generate this file.

Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: socfpga: cyclone5: Enable Macronix flash support

Enable Macronix flash support for Cyclone5 SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>

net: phy: smsc: Add SMSC LAN8741 support

Signed-off-by: Arno Steffens <star@gmx.li>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: e1000: Fix e1000_igb semaphore handling

Fix commit f1bcad22dd19 ("net: e1000: add support for writing to
EEPROM").

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

NET: designware: fix clock enable

After commit ba1f966725223 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.

Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.

If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.

Fix it.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

phy: Fix style violations

Fix some style violations in the generic PHY management code.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

cmd: mdio: Fix style violations

Fix some style violations in the MDIO command.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

net: phy: marvell 88e151x: Fix handling of bare RGMII interface type

Commit 68e6ecadc551 ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.

Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: marvell: Fix style violations

Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

net: tsec: Make live-tree compatible

Make the tsec ethernet driver compatible with a live device tree.

Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

net: tsec: Fix memory leak in error path

tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.

Free the device structure in the error case.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: tsec: Fix style violations

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

ARM: dts: rmobile: Import proper DTS for H2 Stout

Replace the placeholder DTS for R8A7790 H2 Stout with a proper
DTS from Linux next .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 board

Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.

Signed-off-by: Marek Vasut <marex@denx.de>

Merge git://git.denx.de/u-boot-mmc

mmc: omap_hsmmc: use a default 52MHz max clock rate if none is specified

mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

mmc: omap_hsmmc: make it possible to compile out ADMA support

Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

mmc: omap_hsmmc: compile out write support if not needed

This reduces the size of the binary by about 196 bytes.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

mmc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_plat

The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.

This saves around 740 bytes for the am335x_evm SPL.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-rockchip

Merge git://git.denx.de/u-boot-imx

bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDR

Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig.  We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use.  We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig.  In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files.  The previous default
only applied in some cases, even on a specific SoC family.

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

imx: spl: Partially revert "spl: eMMC/SD: Provide one __weak spl_boot_mode() function"

Commit d695d6627803 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:

U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0

Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.

Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>

rockchip: clk: rk3399: handle set_rate/get_rate for PLL_PPLL

The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.

In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.

Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.

References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

rockchip: rk3288: Fix wrong TPL_TEXT_BASE

TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So  0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.

Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff

So, Fix the TEXT_BASE for proper aligned address 0xff704000

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

rockchip: rk3288: Add TPL_LDSCRIPT

Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

rockchip: clk: rk3368: handle clk_enable requests for GMAC

Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
    enabled (no actual action is necessary as the gates are open
    after reset)

References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

rockchip: clk: rk3399: handle clk_enable requests for GMAC

Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.

References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

ARM: dts: i.MX6QDL: icore-rqs: Fix eMMC detection during SPL

usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Remove CONFIG_SYS_BOOTCOUNT_SINGLEWORD

Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's
no remaining uses of it left.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Migrate CONFIG_BOOTCOUNT_ALEN to Kconfig

Convert CONFIG_BOOTCOUNT_ALEN to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Migrate generic bootcount to Kconfig

Make generate boot counter selected in the same way as other boot count
drivers

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Integrate AT91 bootcount driver

Integrate Boot counter for Atmel AT91SAM9XE into Kconfig

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Convert CONFIG_BOOTCOUNT_EXT to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_EXT

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Convert CONFIG_BOOTCOUNT_I2C to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_I2C

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_BOOTCOUNT_RAM to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_RAM

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_BOOTCOUNT_ENV to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_ENV

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_BOOTCOUNT_AM33XX to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_AM33XX

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Prepare for multiple bootcount drivers

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Merge CONFIG_BOOTCOUNT and CONFIG_BOOTCOUNT_LIMIT

CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with
CONFIG_BOOTCOUNT_LIMIT

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Ian Ray <ian.ray@ge.com>

Merge git://git.denx.de/u-boot-video