John Crispin [Sat, 12 Dec 2015 21:01:02 +0000 (21:01 +0000)]
ramips: add missing kernel symbols
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47884
Felix Fietkau [Sat, 12 Dec 2015 12:02:20 +0000 (12:02 +0000)]
kernel: make kmod-crypto-rng depend on kmod-crypto-hash
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47883
Felix Fietkau [Sat, 12 Dec 2015 11:27:51 +0000 (11:27 +0000)]
ar71xx: add rx/tx delay definitons for qca955x's MAC
This patch adds the rx/tx register offsets for the qca955x SoC.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47882
John Crispin [Sat, 12 Dec 2015 07:38:06 +0000 (07:38 +0000)]
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
John Crispin [Sat, 12 Dec 2015 07:37:53 +0000 (07:37 +0000)]
ramips: add support for Spansion S34ML0[24]G2 flash
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47880
John Crispin [Sat, 12 Dec 2015 07:37:45 +0000 (07:37 +0000)]
procd: add 'platform_nand_pre_upgrade'
Add 'platform_nand_pre_upgrade' callback to allow platform specific
preparation right before flashinng, when already in ramdisk.
Example uses might be setting correct values for CI_{KERNPART,UBIPART}.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47879
John Crispin [Sat, 12 Dec 2015 06:42:29 +0000 (06:42 +0000)]
ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
John Crispin [Sat, 12 Dec 2015 06:42:17 +0000 (06:42 +0000)]
ralink: remove stray "+" from ethernet driver
this is what you get if you manually apply patches with c&p
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47877
John Crispin [Sat, 12 Dec 2015 06:42:11 +0000 (06:42 +0000)]
ramips: move partition definitions out of mt7621.dtsi file
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47876
John Crispin [Sat, 12 Dec 2015 06:42:05 +0000 (06:42 +0000)]
ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
Felix Fietkau [Fri, 11 Dec 2015 21:12:14 +0000 (21:12 +0000)]
ar71xx: reorganize target patches/files to make it possible to add boards without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47874
Felix Fietkau [Fri, 11 Dec 2015 21:12:04 +0000 (21:12 +0000)]
ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47873
Felix Fietkau [Fri, 11 Dec 2015 19:22:15 +0000 (19:22 +0000)]
Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit
270a2afcc544ca14e79198346e7e186033472ae7.
SVN-Revision: 47872
Felix Fietkau [Fri, 11 Dec 2015 19:21:59 +0000 (19:21 +0000)]
ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC address
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47871
Felix Fietkau [Fri, 11 Dec 2015 19:21:49 +0000 (19:21 +0000)]
kernel: crypto-aead depends on crypto-null in 4.3 as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47870
Felix Fietkau [Fri, 11 Dec 2015 19:21:43 +0000 (19:21 +0000)]
tools/squashfs4: refresh patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47869
Felix Fietkau [Fri, 11 Dec 2015 19:21:29 +0000 (19:21 +0000)]
build: for refresh, override HOST_QUILT like QUILT
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47868
Jo-Philipp Wich [Fri, 11 Dec 2015 15:26:06 +0000 (15:26 +0000)]
all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Jo-Philipp Wich [Fri, 11 Dec 2015 15:19:43 +0000 (15:19 +0000)]
brcm47xx: migrate network config to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47866
John Crispin [Fri, 11 Dec 2015 15:09:30 +0000 (15:09 +0000)]
firmware-utils: fix various compiler warnings
mostly implicit defines due to missing includes plus one const that
shouldn't be one.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47865
John Crispin [Fri, 11 Dec 2015 15:08:44 +0000 (15:08 +0000)]
mktplinkfw: add missing exceeding bytes info to logs
Add the info on exceeding bytes also to the remaining log messages.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47864
John Crispin [Fri, 11 Dec 2015 15:08:34 +0000 (15:08 +0000)]
uboot-lantiq: fix build with gcc5
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47863
John Crispin [Fri, 11 Dec 2015 15:08:19 +0000 (15:08 +0000)]
procd: update procd.sh to support new ujail options
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 47862
John Crispin [Fri, 11 Dec 2015 15:08:05 +0000 (15:08 +0000)]
procd: bump to latest git HEAD
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47861
John Crispin [Fri, 11 Dec 2015 15:07:40 +0000 (15:07 +0000)]
OpenSSL: Added source/old to PKG_SOURCE_URL
OpenSSL moves old versions of the library from
http://www.openssl.org/source/ to
http://www.openssl.org/source/old/$version/ breaking the old links.
That behavior breaks the OpenWRT-build every time OpenSSL releases
a new version.
This patch adds http://www.openssl.org/source/old/$version/ to the
PKG_SOURCE_URL of OpenSSL to avoid breaking the build whenever
OpenSSL releases a new version.
Signed-off-by: Kevin Kirsch <ranlvor@starletp9.de>
Reviewed-by: Alexander Dahl <post@lespocky.de>
SVN-Revision: 47860
John Crispin [Fri, 11 Dec 2015 15:07:28 +0000 (15:07 +0000)]
tools/squashfs: refresh patches
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47859
John Crispin [Fri, 11 Dec 2015 15:07:15 +0000 (15:07 +0000)]
tools/squashfs: add argument -fixed-time to set all timestamps
-fixed-time <timestamp> set mkfs-timestamp and file-mtime to this timestamp.
Reproducible builds requires the removal of all timestamp or setting all to a specific one.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47858
John Crispin [Fri, 11 Dec 2015 15:06:59 +0000 (15:06 +0000)]
dnsmasq: Add option "--all-servers"
Add the option "--all-servers" which forces dnsmasq to send all
queries to all servers and then take the first answer.
Signed-off-by: Andréas Gustafsson <gurgalof@gmail.com>
SVN-Revision: 47857
John Crispin [Fri, 11 Dec 2015 15:06:45 +0000 (15:06 +0000)]
firmware-utils mkmerakifw: firmware generator for MR18
This patch adds firmware generation tool for Cisco's MR18
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SVN-Revision: 47856
John Crispin [Fri, 11 Dec 2015 15:06:31 +0000 (15:06 +0000)]
base-file: remove /tmp/.jail (now useless)
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 47855
John Crispin [Fri, 11 Dec 2015 15:06:11 +0000 (15:06 +0000)]
base-files: use max_brightness to set LED
LEDs which are controlled by a PWM need to use the supplied
max_brightness instead. Otherwise they might appear to be
very dim / broken.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47854
John Crispin [Fri, 11 Dec 2015 15:06:01 +0000 (15:06 +0000)]
ncurses: Fix build of libncursew
Packages using libncursesw can fail to build if both libncurses and libncursesw
are not installed. Currently the ncurses.h file is installed in "usr/include/ncursesw"
directory and includes other .h files in the "usr/include" directory incorrectly.
For example: Including <ncursesw/ncurses.h> fails due to these references. These build
changes will set the correct include paths within the developer includes.
Packages that expect ncurses.h (or curses.h) in the default "usr/include" path fail
even when expecting to build with libncursesw and will need to be fixed as well. However,
they cannot be fixed until this patch is applied.
Signed-off-by: Ted Hess <thess@kitschensync.net>
SVN-Revision: 47853
John Crispin [Fri, 11 Dec 2015 15:05:53 +0000 (15:05 +0000)]
kernel: Add dummy sound driver
Useful when using sound players that can send to icecast, etc. without any sound device attached.
Signed-off-by: Ted Hess <thess@kitschensync.net>
SVN-Revision: 47852
John Crispin [Fri, 11 Dec 2015 15:05:40 +0000 (15:05 +0000)]
lantiq: get rid of ltq-vdsl-fw
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47851
John Crispin [Fri, 11 Dec 2015 15:05:30 +0000 (15:05 +0000)]
lantiq: fix led setup after switch to uci-defaults-new.sh
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.
This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.
This results for a BTHOMEHUBV5A into the following led configuration:
- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"
With the final result of a switched off power led after boot.
The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47850
John Crispin [Fri, 11 Dec 2015 15:05:20 +0000 (15:05 +0000)]
ar71xx: build image for TL-WR710N v2.1
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47849
John Crispin [Fri, 11 Dec 2015 15:04:57 +0000 (15:04 +0000)]
ar71xx: add LED driver NU801
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47848
John Crispin [Fri, 11 Dec 2015 15:04:47 +0000 (15:04 +0000)]
ar71xx: Add support for Wallys DR344
This patch is for Wallys DR344 support under OpenWRT
Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>
SVN-Revision: 47847
John Crispin [Fri, 11 Dec 2015 15:04:22 +0000 (15:04 +0000)]
ar71xx: image for AP121/16M
Build image for the AP121 reference board with 16MB flash.
Signed-off-by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47846
John Crispin [Fri, 11 Dec 2015 15:04:13 +0000 (15:04 +0000)]
ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
John Crispin [Fri, 11 Dec 2015 15:03:50 +0000 (15:03 +0000)]
ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 47844
John Crispin [Fri, 11 Dec 2015 15:03:39 +0000 (15:03 +0000)]
ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47843
John Crispin [Fri, 11 Dec 2015 15:03:27 +0000 (15:03 +0000)]
ramips: enable CPS for mt7621
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47842
John Crispin [Fri, 11 Dec 2015 15:03:16 +0000 (15:03 +0000)]
ramips: irq handlers do not get irq in 4.3 kernel, update patches
This resolves compilation warnings like this:
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_probe':
drivers/gpio/gpio-mt7621.c:328:46: warning: passing argument 2 of 'irq_set_chained_handler' from incompatible pointer type [-Wincompatible-pointer-types]
irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler);
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47841
John Crispin [Fri, 11 Dec 2015 15:03:08 +0000 (15:03 +0000)]
ramips: Fix CM_GCR_CPC_BASE_CPCBASE_{MSK, SHF} values
Update CM_GCR_CPC_BASE_CPCBASE_{MSK,SHF} to match datasheet
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47840
John Crispin [Fri, 11 Dec 2015 15:02:55 +0000 (15:02 +0000)]
ramips: fold gic patch into mt7621 support patch
All gic patch was doing is removing code added by mt7621 support patch.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47839
John Crispin [Fri, 11 Dec 2015 15:02:50 +0000 (15:02 +0000)]
ramips: backport series of patches that ensure GCRs of other CPUs are accessed properly
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47838
John Crispin [Fri, 11 Dec 2015 15:02:36 +0000 (15:02 +0000)]
ramips: backport batch fixing illegal instruction when booting secodnary CPUs in CPS mode
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47837
John Crispin [Fri, 11 Dec 2015 15:02:13 +0000 (15:02 +0000)]
ramips: mt7621: use symbolic names of gic interrupt settings
This also adds dts nodes for cpc and mc for documentation purposes
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47836
Imre Kaloz [Fri, 11 Dec 2015 13:38:21 +0000 (13:38 +0000)]
mvebu: drop support for old kernels
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47835
Imre Kaloz [Fri, 11 Dec 2015 13:36:30 +0000 (13:36 +0000)]
mvebu: armada-385-rd has been renamed to armada-388-rd upstream
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47834
Jo-Philipp Wich [Fri, 11 Dec 2015 11:00:14 +0000 (11:00 +0000)]
sunxi: fix Lamobo Banana Pi R1 detection
Change the case switch to reflect the value used in the corresponding
device tree file.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47833
Imre Kaloz [Thu, 10 Dec 2015 20:53:02 +0000 (20:53 +0000)]
mvebu: update and fixup 4.4 patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47832
John Crispin [Thu, 10 Dec 2015 19:06:32 +0000 (19:06 +0000)]
ralink: bump to the target to v4.3
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47831
Felix Fietkau [Thu, 10 Dec 2015 14:40:55 +0000 (14:40 +0000)]
br2684ctl: add atm-bridge disabled option
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47830
Felix Fietkau [Thu, 10 Dec 2015 14:40:19 +0000 (14:40 +0000)]
br2684ctl: fix config reload trigger
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47829
Felix Fietkau [Thu, 10 Dec 2015 12:53:30 +0000 (12:53 +0000)]
netifd: ifup-shellscript - fix wrong usage of 'local'
this error was not visible until recent bump to
busybox 1.24.1 stable which introduced a warning message
when keyword 'local' is not used with a shell-function.
this does not change behavior and is a cosmetic cleanup.
fixes the following output:
root@box:~ ifup <interface>
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 1: not in a function
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47828
Felix Fietkau [Thu, 10 Dec 2015 12:40:55 +0000 (12:40 +0000)]
kernel/modules: fix crypto API RNG for >=4.2
Since kernel 4.2, DRBG is the default crypto API RNG, replacing krng. As
DRBG is not enabled, there is no crypto API RNG available when running
kernel 4.2 or later. Because of this, IPsec SAs fail to install. In
strongSwan, this results in a vague error that is difficult to debug:
received netlink error: No such file or directory (2)
Solve this by adding DRBG to the kmod-crypto-rng package. As enabling
DRBG in the kernel config also enables the Jitterentropy RNG, include it
in kmod-crypto-rng instead of having it in a separate package.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47827
Felix Fietkau [Thu, 10 Dec 2015 12:40:19 +0000 (12:40 +0000)]
popt: remove xgettext prereq check, it is not necessary
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47826
Felix Fietkau [Thu, 10 Dec 2015 12:40:08 +0000 (12:40 +0000)]
scripts/download.pl: cleanup GNOME source location definitions
Cleanup the @GNOME source download location definitions:
* remove dead and stale mirrors
* adjust to changes at directory structure
* add one new working mirror
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47825
Felix Fietkau [Thu, 10 Dec 2015 12:39:51 +0000 (12:39 +0000)]
tools/mm-macros: update to 0.9.9
Update mm-macros (mm-common) to 0.9.9.
Switch to use the @GNOME source download location.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47824
Felix Fietkau [Thu, 10 Dec 2015 12:39:32 +0000 (12:39 +0000)]
build: fix arch used during dts compilation
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47823
Imre Kaloz [Thu, 10 Dec 2015 12:17:24 +0000 (12:17 +0000)]
mac80211: use the linux-firmware tree from 2015-12-07
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47822
Imre Kaloz [Thu, 10 Dec 2015 12:14:19 +0000 (12:14 +0000)]
generic/4.1: refresh patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47821
Imre Kaloz [Thu, 10 Dec 2015 12:13:16 +0000 (12:13 +0000)]
mvebu: fixup wifi macs for Linksys boards
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47820
Imre Kaloz [Thu, 10 Dec 2015 12:11:39 +0000 (12:11 +0000)]
mvebu: add support for 4.4-rc
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47819
Imre Kaloz [Thu, 10 Dec 2015 12:08:13 +0000 (12:08 +0000)]
mvebu: add support for 4.1 and switch over
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47818
Hauke Mehrtens [Wed, 9 Dec 2015 22:26:40 +0000 (22:26 +0000)]
openssl: add config option for no_hw support
The hardware support is required by some 3rd party engines (tpm)
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 47817
Jo-Philipp Wich [Wed, 9 Dec 2015 19:42:00 +0000 (19:42 +0000)]
ubus: fix various ACL processing problems
Bump ubus to current Git HEAD in order to:
* Fix a null pointer access when user ACLs are loaded into memory
* Fix wrong permission handling for uid=0, gid!=0 peers
* Fix return code for permission defined cases
* Fix socket error handling when the server connection dies
* Make ACL file path configurable
* Remove invalid usages of poll() when using a zero timeout
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47816
Jo-Philipp Wich [Wed, 9 Dec 2015 15:19:41 +0000 (15:19 +0000)]
mac80211: fix passing of VHT80 in IBSS mode
The "iw" utility expects the VHT80 to be specified as uppercase "80MHZ",
change the script to reflect that.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47814
Jo-Philipp Wich [Wed, 9 Dec 2015 15:18:43 +0000 (15:18 +0000)]
mac80211: fix disabling HT in IBSS mode (#21340)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47813
Felix Fietkau [Tue, 8 Dec 2015 00:14:41 +0000 (00:14 +0000)]
kernel: revert fq_codel quantum override to prevent it from causing too much cpu load with higher speed (#21326)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47811
Rafał Miłecki [Mon, 7 Dec 2015 20:43:49 +0000 (20:43 +0000)]
bcm53xx: update BCM5301X SMP patch to fixed version from stblinux
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47810
Rafał Miłecki [Mon, 7 Dec 2015 19:56:12 +0000 (19:56 +0000)]
bcm53xx: fix selecting HAVE_SMP symbol in Kconfig
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47809
Rafał Miłecki [Mon, 7 Dec 2015 19:20:40 +0000 (19:20 +0000)]
bcm53xx: use backported BCM5301X patches from stblinux soc/next
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47807
Rafał Miłecki [Mon, 7 Dec 2015 18:38:20 +0000 (18:38 +0000)]
brcm47xx: make bcm47xxpart patch apply after recent backports
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47806
Imre Kaloz [Mon, 7 Dec 2015 10:13:55 +0000 (10:13 +0000)]
generic: add missing 4.1 symbols
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47802
Imre Kaloz [Mon, 7 Dec 2015 10:11:43 +0000 (10:11 +0000)]
generic: bump 4.4 to rc4
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 47801
Rafał Miłecki [Mon, 7 Dec 2015 09:31:52 +0000 (09:31 +0000)]
kernel: add bcm47xxpart patches sent for 4.5 merge window
This replaces old bcm53xx patch for scanning whole flash and makes
bcm47xxpart compatible with NAND.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47800
Felix Fietkau [Sun, 6 Dec 2015 14:25:36 +0000 (14:25 +0000)]
ar71xx: fix switch port mapping for tl-wdr4300/3600
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47799
Hauke Mehrtens [Sun, 6 Dec 2015 13:49:03 +0000 (13:49 +0000)]
kernel: add missing config option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47798
Hauke Mehrtens [Sun, 6 Dec 2015 13:41:26 +0000 (13:41 +0000)]
ar7-atm: fix build with gcc 5
Remove the usage of the __TIME__ and __DATE__ macro.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47797
Hauke Mehrtens [Sun, 6 Dec 2015 13:32:36 +0000 (13:32 +0000)]
kernel: add missing config options for kernel 4.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47796
Hauke Mehrtens [Sun, 6 Dec 2015 13:31:58 +0000 (13:31 +0000)]
mac80211: fix build of mac80211-hwsim on kernel 4.4
This genl_notify() backport should not be applied for kernel 4.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47795
Jo-Philipp Wich [Sun, 6 Dec 2015 08:41:22 +0000 (08:41 +0000)]
lantiq: fix logic error in dsl board.d code
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47793
Hauke Mehrtens [Sat, 5 Dec 2015 15:45:31 +0000 (15:45 +0000)]
cyassl: update to wolfSSL version 3.7.0
This version and version 3.6.8 are fixing the following security problems:
* CVE-2015-7744
* CVE-2015-6925
The activation of SSLv3 support is needed for curl.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47791
Hauke Mehrtens [Sat, 5 Dec 2015 15:44:58 +0000 (15:44 +0000)]
update mtd-utils to 1.5.2
- update mtd-utils to 1.5.2 (git
a494d30ab1ae40cb7665680cadf5af3ca3830a73)
- remove patches that went upstream
- fixes build from scratch as of broken patches
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[use the final version of 1.5.2 instead, fix header of jffs2_lzma_(de,)compress()]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47790
Felix Fietkau [Sat, 5 Dec 2015 13:11:28 +0000 (13:11 +0000)]
kernel: fix linux 4.4 mac80211 build error
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47789
Felix Fietkau [Sat, 5 Dec 2015 09:57:19 +0000 (09:57 +0000)]
lldpd: add STOP=01 param in init script
This should ensure that lldpd is among the first processes to stop,
so that it has time to send the shutdown LLDPU to the other side,
before the network goes down.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47786
Felix Fietkau [Sat, 5 Dec 2015 09:52:42 +0000 (09:52 +0000)]
lantiq: add VDSL2 vectoring status information
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47785
Felix Fietkau [Sat, 5 Dec 2015 09:52:36 +0000 (09:52 +0000)]
lantiq: ltq-vdsl-mei: enable vectoring support
Dynamic Spectrum Management is a precondition for G.993.5 (VDSL2 vectoring).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47784
Felix Fietkau [Sat, 5 Dec 2015 09:52:30 +0000 (09:52 +0000)]
lantiq: get rid of the dsl_fw mtd partition
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47783
Felix Fietkau [Sat, 5 Dec 2015 09:52:18 +0000 (09:52 +0000)]
iw: add VHT80 support for 802.11s
Support next to the non-HT/HT channel widths like HT20 or NOHT also VHT80
channels during the mesh join
iw dev mesh0 mesh join "meshnet" freq 5180 80MHz
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47782
Felix Fietkau [Sat, 5 Dec 2015 09:52:10 +0000 (09:52 +0000)]
mac80211: Allow to select VHT80 in IBSS mode
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47781
Felix Fietkau [Sat, 5 Dec 2015 09:52:02 +0000 (09:52 +0000)]
iw: add VHT80 support for IBSS
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47780
Felix Fietkau [Sat, 5 Dec 2015 09:51:53 +0000 (09:51 +0000)]
iw: display interface TX power if available
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47779
Felix Fietkau [Sat, 5 Dec 2015 09:51:48 +0000 (09:51 +0000)]
iw: sync nl80211.h with compat-wireless 2015-10-26
Fix the id of NL80211_ATTR_WIPHY_ANTENNA_GAIN for antenna_gain command when
using compat-wireless 2015-10-26.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47778
Felix Fietkau [Sat, 5 Dec 2015 09:51:39 +0000 (09:51 +0000)]
iw: update to version 4.3
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47777
Felix Fietkau [Sat, 5 Dec 2015 09:51:35 +0000 (09:51 +0000)]
mac80211: Allow enabling tracing for the drivers that support it
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47776
Felix Fietkau [Sat, 5 Dec 2015 09:51:30 +0000 (09:51 +0000)]
busybox: Update config for 1.24.1
r47288 updated to Busybox 1.24.1 but did not update the configuration.
The configuration is updated by running
cd config
../convert_menuconfig.pl .../build_dir/target-*/busybox-1.24.1
cd ..
./convert_defaults.pl < .../build_dir/target-*/busybox-1.24.1/.config > \
Config-defaults.in
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 47775
projects / librecmc / librecmc.git / log