Vladimir Vid [Tue, 23 Jul 2019 16:46:15 +0000 (18:46 +0200)]
kernel: add i2c-pxa driver
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Vladimir Vid [Thu, 11 Jul 2019 17:55:46 +0000 (19:55 +0200)]
kernel: 4.19: backport mx25u12835f support from linux 5.0
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
DENG Qingfang [Thu, 22 Aug 2019 04:14:00 +0000 (12:14 +0800)]
iproute2: update to 5.2.0
Remove upstream patches
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Felix Fietkau [Sat, 24 Aug 2019 10:41:19 +0000 (12:41 +0200)]
mac80211: fix a regression in the minstrel_ht improvement patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Luochongjun [Fri, 23 Aug 2019 09:05:57 +0000 (17:05 +0800)]
ath79: add support for gl-ar750
This patch supports gl-ar750, which was previously supported by ar71xx.
Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 2xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- LED: 3x LEDS (white)
Flash instruction:
Support for sysupgrade directive upgrades, as well as luci upgrades.
Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
Zhenjian Zhang [Tue, 13 Aug 2019 06:30:29 +0000 (14:30 +0800)]
ramips: add support for ADSLR G7
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N
Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.
Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Daniel Golle [Fri, 23 Aug 2019 16:09:04 +0000 (18:09 +0200)]
mac80211: rt2x00: import pending patches
https://patchwork.kernel.org/patch/
11111605/
https://patchwork.kernel.org/patch/
11110703/
Fixes:
91c84e87c249 ("mac80211: rt2x00: clear IV's on start to fix AP mode regression")
Fixes:
0b2c42ced21a ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Thu, 22 Aug 2019 00:59:24 +0000 (14:59 -1000)]
ipqx0xx: add Generic subtarget
Both targets miss a subtarget causing an image naming style which is
different from other all othe targets, even tho it already uses
`x/generic/` as subfolder as if the subtarget would exist.
This commit adds the Generic subtarget resulting in consistent naming.
~/src/openwrt/openwrt/bin/targets/ipq806x/generic$ ls
openwrt-ipq806x-generic-netgear_d7800-initramfs-uImage
openwrt-ipq806x-generic-netgear-d7800.manifest
openwrt-ipq806x-generic-netgear_d7800-squashfs-factory.img
openwrt-ipq806x-generic-netgear_d7800-squashfs-sysupgrade.bin
CC: John Crispin <john@phrozen.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Daniel Golle [Thu, 22 Aug 2019 14:23:18 +0000 (16:23 +0200)]
lantiq: add device alias for Alpha ASL56026
BT Openreach ECI VDSL Modem V-2FUb/I is an alias of Alpha ASL56026 as
also stated in the original commit message adding the device
(commit
6254a2028c "lantiq: add support for the Alpha ASL56026").
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adrian Schmutzler [Thu, 22 Aug 2019 12:09:50 +0000 (14:09 +0200)]
lantiq: sort device definitions in image/Makefile
This sorts the device definitions in image/Makefile alphabetically
for each subtarget/block.
The order of blocks has not been touched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Rafał Miłecki [Fri, 16 Aug 2019 15:02:58 +0000 (17:02 +0200)]
treewide: sysupgrade: pass "save_partitions" option to the "sysupgrade" method
This explicitly lets stage2 know if partitions should be preserved. No
more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 16 Aug 2019 14:54:38 +0000 (16:54 +0200)]
base-files: pass "save_config" option to the "sysupgrade" method
This explicitly lets stage2 know if config should be preserved.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 22 Aug 2019 11:45:45 +0000 (13:45 +0200)]
procd: update to latest git HEAD
9558031 system: support passing "options" to the "sysupgrade" ubus method
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Thu, 22 Aug 2019 11:22:39 +0000 (13:22 +0200)]
ramips: add device alias for Allnet ALL0239-3G
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Thu, 15 Aug 2019 19:53:10 +0000 (09:53 -1000)]
ramips/mt76x8: add DEVICE_VENDOR for tl-wr840n-v5
DEVICE_VENDOR is missing for this device.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Wed, 14 Aug 2019 18:51:36 +0000 (08:51 -1000)]
image.mk: keep underscores when sanitize PROFILE
Underscores don't harm in filenames, however the sanitize function from
version.mk replaces them, causing inconsistent filenames.
A fix tried to solve this previously via
dfe99645dbdd4460f394beaa3a05091cd40b5942 however I did not look close
enough:
openwrt-ath79-generic-8dev-carambola2.manifest # current
openwrt-ath79-generic_8dev-carambola2.manifest # patched
---------------------^
Eventually the sanitization of PROFILES *could* be removed as more and
more profiles follow the device tree approach of vendor_model, neither
containing upper case letters nor spaces.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Moritz Warning [Thu, 11 Jul 2019 10:47:56 +0000 (12:47 +0200)]
lantiq: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Paul Spooren [Tue, 16 Jul 2019 11:56:08 +0000 (13:56 +0200)]
build: introduce ALT vendor/model/variant
Some devices are produced and sold under different names. To debloat
the buildroot but keeping it complete, new variables are introduced to
handle different namings. Below an example taken from a recent PR[0]
DEVICE_VENDOR := Arcadyan
DEVICE_MODEL := ARV4520PW
DEVICE_ALT0_VENDOR := Vodafone
DEVICE_ALT0_MODEL := Easybox 800
DEVICE_ALT1_VENDOR := Airties
DEVICE_ALT1_MODEL := WAV-281
With this commit the buildroot is extended to take care of up to three
alternative namings. The primary title plus alternatives names (if
defined) are shown in the `make menuconfig` dialog. Selecting on of
devices automatically selects all alternative names as they share the
same profile.
A list of the newly introduced variables:
DEVICE_ALT0_VENDOR :=
DEVICE_ALT0_MODEL :=
DEVICE_ALT0_VARIANT :=
DEVICE_ALT1_VENDOR :=
DEVICE_ALT1_MODEL :=
DEVICE_ALT1_VARIANT :=
DEVICE_ALT2_VENDOR :=
DEVICE_ALT2_MODEL :=
DEVICE_ALT2_VARIANT :=
[0]: https://github.com/openwrt/openwrt/pull/2229/files#diff-b436f01932a18876c27800ba183d95f6R140
Signed-off-by: Paul Spooren <mail@aparcar.org>
Kevin Darbyshire-Bryant [Tue, 20 Aug 2019 11:29:47 +0000 (12:29 +0100)]
firewall: update to latest git HEAD
bf29c1e firewall3: ipset: Handle reload_set properly
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Felix Fietkau [Wed, 21 Aug 2019 11:11:13 +0000 (13:11 +0200)]
mac80211: backport support for the IEEE80211_KEY_FLAG_GENERATE_MMIE flag
Required for an upcoming mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 14 Jun 2019 19:32:15 +0000 (21:32 +0200)]
mac80211: add new minstrel_ht patches to improve probing on mt76x2
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 19 Aug 2019 17:15:35 +0000 (19:15 +0200)]
mac80211: renumber subsys patches after update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 19 Aug 2019 17:14:17 +0000 (19:14 +0200)]
mac80211: remove TX_NEEDS_ALIGNED4_SKBS patch
The intended performance benefit could not be reliably reproduced, and the
patch was not accepted upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Yousong Zhou [Mon, 19 Aug 2019 13:39:18 +0000 (13:39 +0000)]
scripts/dl_github_archive.py: fix python3 transition
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Luiz Angelo Daros de Luca [Mon, 19 Aug 2019 03:09:05 +0000 (00:09 -0300)]
elfutils: bump to 0.177
200-uclibc-ng-compat.patch is upstream now.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Daniel Golle [Mon, 19 Aug 2019 11:40:51 +0000 (13:40 +0200)]
mac80211: rt2x00: clear IV's on start to fix AP mode regression
To do not brake HW restart we should keep initialization vectors data.
I assumed that on start the data is already initialized to zeros, but
that not true on some scenarios and we should clear it. So add
additional flag to check if we are under HW restart and clear IV's
data if we are not.
Patch fixes AP mode regression.
Patch pending on linux-wireless and imported from patchwork.
Fixes:
0b2c42ced21a ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hauke Mehrtens [Sun, 18 Aug 2019 23:02:43 +0000 (01:02 +0200)]
gcc: Update gcc 9.X to version 9.2.0
This updates the GCC version 9.X to version 9.2.0.
The removed patches are applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 18 Aug 2019 21:24:43 +0000 (23:24 +0200)]
musl: Fix CVE-2019-14697
musl libc through 1.1.23 has an x87 floating-point stack adjustment
imbalance, related to the math/i386/ directory. In some cases, use of
this library could introduce out-of-bounds writes that are not present
in an application's source code.
This problem only affects x86 and no other architectures.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 18 Aug 2019 20:16:34 +0000 (22:16 +0200)]
linux-firmware: intel: Use recent version of wifi firmware
iwlwifi from the new backports also supports more recent FW versions,
update to the most recent versions for already supported devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 18 Aug 2019 19:12:52 +0000 (21:12 +0200)]
mac80211: ath10k: Fix crashes of QCA9984 when station connects
This fixes a bug introduced in backports from kernel 5.1 which makes
ath10k crash on QCA9984 when a station connects. The FW sends a airtime
report, but this station is not yet fully registered and a NULL pointer
is used.
Fixes:
0b2c42ced21a ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Lamparter [Sat, 17 Aug 2019 21:13:32 +0000 (23:13 +0200)]
ipq-wifi: drop upstreamed custom board-2.bin
The BDFs for the:
ALFA Network AP120C-AC
ASUS Lyra
AVM FRITZ!Box 7530
AVM FRITZ!Repeater 3000
EnGenius EAP1300
EnGenius ENS620EXT
Netgear Orbi Pro SRK60
boards were upstreamed to the ath10k-firmware repository
and linux-firmware.git.
Furthermore the BDFs for the:
OpenMesh A42 specific BDFs
OpenMesh A62 specific BDFs
Linksys EA6350v3
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 17 Aug 2019 21:03:41 +0000 (23:03 +0200)]
linux-firmware: update to
20190815
Update linux-firmware to
20190815
git log --pretty=oneline --abbrev-commit
20190815..
20190815
07b925b Install only listed firmware files
5621bfc rtw88: add a README file
7e431c5 rtw88: RTL8822C: add WoW firmware v7.3
2dc7023 rtw88: RTL8822C: update rtw8822c_fw.bin to v7.3
d3d000d Merge branch 'ath10k-
20190808' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
d3e17e9 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
d3f7234 Merge commit '
70af908f4ad7aa8bc65032253f99a0a4fbe1e6c3' of https://github.com/Netronome/linux-firmware
1f0a99f ath10k: QCA9984 hw1.0: update board-2.bin
49c1187 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00046
1031f01 ath10k: QCA988X hw2.0: update firmware-5.bin to 10.2.4-1.0-00045
cf714a2 ath10k: QCA9888 hw2.0: update board-2.bin
81e2e77 ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00040
8dc2dfb ath10k: QCA9887 hw1.0: update firmware-5.bin to 10.2.4-1.0-00045
1bd3ef2 ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00140-QCARMSWPZ-1
e043109 ath10k: QCA4019 hw1.0: update board-2.bin
b1e26aa cxgb4: update firmware to revision 1.24.3.0
70af908 nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.10.A.38
dff98c6 Merge branch 'master' of git://github.com/skeggsb/linux-firmware
580b076 Merge branch 'nxp_mc' of https://github.com/NXP/linux-firmware
f9b0071 Merge tag 'iwlwifi-fw-2019-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
2a3b75d nvidia: add missing entries in WHENCE
6fc1eb1 linux-firmware: Update NXP Management Complex firmware to version 10.16.2
cd6cb7b iwlwifi: update -48 FWs for Qu and cc
b5f09bb iwlwifi: update FWs for 3168, 7265D, 9000, 9260, 8000, 8265 and cc
bf13a71 Merge branch 'guc_v33' of git://anongit.freedesktop.org/drm/drm-firmware
d52556e linux-firmware: Update firmware file for Intel Bluetooth AX201
dbcc2fb linux-firmware: Update firmware file for Intel Bluetooth 22161
a5ee415 linux-firmware: Update firmware file for Intel Bluetooth 9560
7444ca4 linux-firmware: Update firmware file for Intel Bluetooth 9260
3d1e553 amdgpu: update vega10 VCE firmware
5d4e3cc amdgpu: update picasso vcn firmware
6a45d9e amdgpu: update raven vcn firmware
9c8161f amdgpu: update tonga to latest 19.20 firmware
7b6c49c amdgpu: update vega12 to latest 19.20 firmware
4f7b71b amdgpu: partially revert
2579167548be33afb1fe2a9a5c141561ee5a8bbe
fd3cc24 amdgpu: update vega10 to latest 19.20 firmware
c190efa amdgpu: update polaris12 to latest 19.20 firmware
f42b54e amdgpu: update raven2 to latest 19.20 firmware
fc89ce8 amdgpu: update raven to latest 19.20 firmware
3bebb5a amdgpu: update picasso to latest 19.20 firmware
05dbae6 drm/i915/firmware: Add v33 of GuC for ICL
786f17a drm/i915/firmware: Add v33 of GuC for KBL
aae0eb5 drm/i915/firmware: Add v33 of GuC for SKL
9cf240f drm/i915/firmware: Add v33 of GuC for GLK
8a0a6a6 drm/i915/firmware: Add v33 of GuC for BXT
70e4394 linux-firmware: rsi: add firmware image for redpine 9116 chipset
fd69a5d linux-firmware: Add firmware file for Intel Bluetooth AX201
7ae3a09 Merge tag 'iwlwifi-fw-2019-06-20' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
90e6845 iwlwifi: add new firmwares for integrated 22000 series
71ef30c iwlwifi: update FW for 22000 to Core45-96
e58cbf7 iwlwifi: update FWs for 9000 series to Core45-96
b443218 iwlwifi: update Core45 FWs for 22260, 9000 and 9260
5157165 iwlwifi: udpate -36 firmware for 8000 series
This commit was created with the help of the make-package-update-commit.sh script.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 18 Aug 2019 00:31:01 +0000 (02:31 +0200)]
iftop: update to HEAD of 2018-10-03 - 77901c
Update iftop to commit
77901c8c53e01359d83b8090aacfe62214658183
git log --pretty=oneline --abbrev-commit
949ed0f7..
77901c8c
77901c8 Support scales beyond 1Gbps
Created with the help of the make-package-update-commit.sh script.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Jo-Philipp Wich [Sun, 18 Aug 2019 18:00:06 +0000 (20:00 +0200)]
uhttpd: update to latest Git HEAD
6b03f96 ubus: increase maximum ubus request size to 64KB
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Hans Dedecker [Sun, 18 Aug 2019 16:54:47 +0000 (18:54 +0200)]
nghttp2: bump to 1.39.2
957abacf Bump up version number to 1.39.2, LT revision to 32:0:18
83d362c6 Don't read too greedily
a76d0723 Add nghttp2_option_set_max_outbound_ack
db2f612a nghttpx: Fix request stall
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Yousong Zhou [Sun, 18 Aug 2019 15:21:23 +0000 (15:21 +0000)]
ltq-ifxos: refer to https://bugs.openwrt.org
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Sun, 18 Aug 2019 15:19:57 +0000 (15:19 +0000)]
ct-bugcheck: report to https://openwrt.org by default
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Sun, 18 Aug 2019 15:18:10 +0000 (15:18 +0000)]
download.pl: use https://source.openwrt.org
https://sources.lede-openwrt.org now redirects to there
https://downloads.openwrt.org/sources returns 404, so remove it here
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Luis Araneda [Sun, 18 Aug 2019 14:59:11 +0000 (10:59 -0400)]
u-boot.mk: use openwrt url instead of lede project
The LEDE URL is automatically redirected to the OpenWRT one,
returning an HTTP 301 code (Moved Permanently).
Also, use https, as indicated by the redirect.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Deng Qingfang [Sun, 16 Dec 2018 15:49:07 +0000 (23:49 +0800)]
ramips: add MT7530 switch port-mirroring support
Compile & run tested on MT7620, MT7621
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
[Tested on Phicomm PSG1218 rev.A, MediaTek MT7620A ver:2 eco:6]
Tested-by: MingHao Chen <cmheia@email.com>
Alin Nastac [Mon, 1 Jul 2019 08:57:26 +0000 (10:57 +0200)]
iproute2: add libcap support, enabled in ip-full
Preserve optionality of libcap by having configuration script follow the
HAVE_CAP environment variable, used similarly to the HAVE_ELF variable.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase/refresh patches]
James Taylor [Wed, 5 Jun 2019 12:22:15 +0000 (22:22 +1000)]
lua: add lua.hpp to InstallDev
This is necessary to build PowerDNS authoritative and recursor against
OpenWRT, and may avoid packages depending on lua/host unnecessarily.
Signed-off-by: James Taylor <james@jtaylor.id.au>
Hauke Mehrtens [Sun, 18 Aug 2019 11:58:21 +0000 (13:58 +0200)]
rtl8812au-ct: Add vendor command policy
Fixes:
928e893a11db ("mac80211: Update to version 5.3-rc4-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Boris Krasnovskiy [Sun, 18 Aug 2019 00:04:00 +0000 (20:04 -0400)]
mwlwifi: Fix loading with backports v5.3
This adds a vendor command policy which is enforced since mac80211 from
kernel 5.3
Fixes:
928e893a11db ("mac80211: Update to version 5.3-rc4-1")
Signed-off-by: Boris Krasnovskiy <boris.krasnovskiy@lairdtech.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 21:02:17 +0000 (21:02 +0000)]
at91/image/sama5.mk: check for sama5d4_xplained device
check for sama5d4_xplained device while copying at91bootstrap binary
to sdcard image.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 21:02:16 +0000 (21:02 +0000)]
at91: remove Build/at91-sdcard command
remove at91-sdcard build command from Makefile as this is moved to
respective subtarget Makefile.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:15 +0000 (00:42 +0000)]
at91: add uboot environments
add uboot environments to sdcard image
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:15 +0000 (00:42 +0000)]
at91: move at91-sdcard command to sama5.mk
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:15 +0000 (00:42 +0000)]
at91bootstrap: add sama5d27_som1_eksd1_uboot as default defconfig
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:14 +0000 (00:42 +0000)]
at91bootstrap: add support for at91sam9x5ek
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:14 +0000 (00:42 +0000)]
at91bootstrap: bump v3.8.10 to v3.8.12
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:14 +0000 (00:42 +0000)]
uboot-at91: fix -Wformat-security
add patch to fix -Wformat-security warnings.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:13 +0000 (00:42 +0000)]
uboot-at91: changed som1 ek default defconfigs
replaced som1 ek spi flash with qspi defconfig and mmc with mmc1
defconfig.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:13 +0000 (00:42 +0000)]
uboot-at91: add at91sam9x5ek soc
add support to build u-boot binaries for at91sam9x5ek socs.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Sandeep Sheriker M [Wed, 14 Aug 2019 00:42:12 +0000 (00:42 +0000)]
uboot-at91: bump linux4sam_5.8 to linux4sam_6.0
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Chen Minqiang [Wed, 7 Aug 2019 00:58:48 +0000 (08:58 +0800)]
ramips: fix switch ports settings
This change the switch settings for:
HC5661: 4 lan ports + 1 wan port
Y1S: 2 lan ports(G port) + 2 lan ports(E port) + 1 wan port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Chen Minqiang [Wed, 6 Mar 2019 11:04:26 +0000 (19:04 +0800)]
ramips: hc5xxx: use switch trigger for leds
netdev on eth0.2 can't show link status of wan port because eth0 is
connected to builtin switch and is always link up. Use swconfig
trigger instead.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Adrian Schmutzler [Mon, 12 Aug 2019 13:12:02 +0000 (15:12 +0200)]
ath79: create DTSI for ar9341 TP-Link devices
This patch creates a shared DTSI for the TP-Link devices based
on ar9341 as those share a lot of definitions.
While at it, change from gpio-keys-polled to gpio-keys, remove
unused pll-data and remove some inherited stuff, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Lim Guo Wei [Mon, 12 Aug 2019 07:54:11 +0000 (15:54 +0800)]
ath79: migrate TP-Link TL-MR3420v2 to ath79
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac
Flash instruction:
Upload generated factory firmware on vendor's web interface.
This changes the key assignment compared to ar71xx support of this
device, since of the two keys on the device one is used as combined
Reset/WPS and the second one as WiFi on/off button.
Despite, the reset button required GPIO_ACTIVE_HIGH to work correctly.
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
xixiao zheng [Tue, 25 Jun 2019 08:32:58 +0000 (16:32 +0800)]
ath79: add support for PISEN TS-D084
PISEN TS-D084 is an wireless router with a battery and integrated power
supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
Upload generated factory image through web interface.
Signed-off-by: xixiao zheng <xixiaozheng64@gmail.com>
[wrap commit message, add flash instruction]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Sungbo Eo [Sat, 20 Jul 2019 18:34:59 +0000 (03:34 +0900)]
ramips: add support for ipTIME A604M
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Chuanhong Guo [Sat, 10 Aug 2019 12:00:24 +0000 (20:00 +0800)]
ath79: adtran,bsap1840/bsap1800-v2: move bootcount out of 02_network
These device supports were introduced before /etc/init.d/bootcount and they
had a bootcount reset done in /etc/board.d/02_network.
Move it into /etc/init.d/bootcount instead.
Suggested-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 10 Aug 2019 11:35:56 +0000 (19:35 +0800)]
treewide: sync bootcount scripts across targets
This commit made the following changes to sync all bootcount scripts:
1. use boot() instead of start()
This script only needs to be executed once when boot is complete.
use boot() to make this explicit.
2. drop sourcing of /lib/functions.sh
This is aready done in /etc/rc.common.
3. ramips: replace board name checking with a case
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Hauke Mehrtens [Sat, 17 Aug 2019 15:09:42 +0000 (17:09 +0200)]
ustream-ssl: update to latest git HEAD
e8f9c22 Revise supported ciphersuites
7e9e269 wolfssl, openssl: use TLS 1.3, set ciphersuites
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Engberg [Sat, 15 Jun 2019 09:47:21 +0000 (09:47 +0000)]
tools/e2fsprogs: Update to 1.45.3
Update e2fsprogs to 1.45.3
Remove OpenBSD patch
Remove Darwin patch, neither macports or brew patches these files
Add patch to avoid crond detection on host OS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Florian Eckert [Mon, 12 Aug 2019 10:04:04 +0000 (12:04 +0200)]
target/x86/image: use qemu-img from STAGING_DIR_HOST
The host tool package qemu is build for the target x86. The installed tool
qemu-img is needed to build vdi or vmdk images. In the image Makefile we
use however the host installed qemu-img command and not the tool from the
buildsystem. This commit force to use the already build qemu-img command
from the openwrt toolchain.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Luiz Angelo Daros de Luca [Fri, 16 Aug 2019 04:33:58 +0000 (01:33 -0300)]
musl: ldso/dlsym: fix mips returning undef dlsym
This happens only the second time a library is loaded by dlopen().
After lib1 is loaded, dlsym(lib1,"undef1") correctly resolves the undef
symbol from lib1 dependencies. After the second library is loaded,
dlsym(lib2,"undef1") was returning the address of "undef1" in lib2
instead of searching lib2 dependencies.
Using upstream fix which now uses the same logic for relocation time
and dlsym.
Fixes openwrt/packages#9297
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Linus Walleij [Wed, 17 Jul 2019 17:23:32 +0000 (19:23 +0200)]
gemini: Enable flash boot on reference design type
The flash layout on the Storlink reference design for Gemini
is using 2 MB flash for the kernel, and it also insists on
overwriting the partition table with default values on every
boot. The same is true for the SQ201. This poses a problem
on recent OpenWrt firmware as the base zImage is bigger
than 2 MB.
At the same time there is a ramdisk partition of 6 MB that we
don't really need. The partition table looks like this:
Creating 7 MTD partitions on "
30000000.flash":
0x000000000000-0x000000016000 : "BOOT"
0x000000120000-0x000000320000 : "Kern"
0x000000320000-0x000000920000 : "Ramdisk"
0x000000920000-0x000000f20000 : "Application"
0x000000f20000-0x000000f40000 : "VCTL"
0x000000f40000-0x000000fe0000 : "CurConf"
0x000000fe0000-0x000001000000 : "FIS directory"
On boot the "Kern" partition is copied to RAM @0x01600000
and the "Ramdisk" partition is copied to RAM @0x00800000.
Then the kernel is executed.
The idea with this patch is to extend the "Kern" partition
with the "Ramdisk" partition to get a full 8 MB to use
for the kernel. Then we put the OpenWrt JFFS2 rootfs
inside the "Application" partition.
We create a small assembly loop that we prepend to the
"Kern" image that will copy the "Kern" from 0x0160000
and the "Ramdisk" from 0x00800000 and put them in
consecutive space at 0x00400000 and execute it from
there, using "Application" as rootfs.
We generate 3 main files:
- zImage - contains the assembly bootstrap loop and
the first part of the generated kernel image
- rd.gz - contains the second part of the generated
kernel image
- hddapp.tgz - contains the root filesystem
On the SQ201 I flash these manually using the native boot
loader PLATO, "Y" alternative for the zImage, "R" for
the rd.gz image and "A" for hddapp.tgz.
This works fine and I can now boot to prompt on the SQ201
with nothing but flash.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 17 Jul 2019 17:23:31 +0000 (19:23 +0200)]
gemini: Add copy-kernel utility package
This package just contains a small Gemini-only assembler
bootstrap loop to copy the kernel from the two fragments
(previously zImage at 0x01600000 and initramdisk at 0x00800000)
into one big zImage of up to 8 MB at 0x00400000.
It will be built on demand from the Gemini image Makefile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 17 Jul 2019 17:22:40 +0000 (19:22 +0200)]
gemini: Fix up flash accesses
The SL93512r and the NAS4220B have Redboot partition
tables (rely on these) and need to boot from mtdblock3.
Add two patches from upstream to fix this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 17 Jul 2019 17:21:48 +0000 (19:21 +0200)]
gemini: Fix up some confused pin config on SL93512r
Upstream patch fixing the errors in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Luis Araneda [Sun, 4 Aug 2019 04:32:06 +0000 (00:32 -0400)]
zynq: remove kernel 4.14 support
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Sun, 4 Aug 2019 04:32:05 +0000 (00:32 -0400)]
zynq: switch to kernel 4.19
Use kernel 4.19 by default
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Sun, 4 Aug 2019 04:32:04 +0000 (00:32 -0400)]
zynq: k4.19: fix kernel panic on smp bring-up
This fixes a kernel panic when validating the
arguments of memcpy at runtime, which is enabled
by generic's CONFIG_FORTIFY_SOURCE for k4.19
This wasn't triggered on 4.14, as ARCH_HAS_FORTIFY_SOURCE
was added on k4.17 for the ARM architecture
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Sun, 4 Aug 2019 04:32:03 +0000 (00:32 -0400)]
zynq: kernel: use some configs provided by generic
- Select CONFIG_PREEMPT_NONE (server) instead
of CONFIG_PREEMPT (low-latency desktop)
- Remove CONFIG_USELIB
- Remove CONFIG_SYSCTL_SYSCALL
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Sun, 4 Aug 2019 04:32:02 +0000 (00:32 -0400)]
zynq: add k4.19 config
Copied from kernel 4.14 and refreshed
with make kernel_oldconfig
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Eneas U de Queiroz [Mon, 5 Aug 2019 14:47:58 +0000 (11:47 -0300)]
wolfssl: bump to 4.1.0-stable
Always build AES-GCM support.
Unnecessary patches were removed.
This includes two vulnerability fixes:
CVE-2019-11873: a potential buffer overflow case with the TLSv1.3 PSK
extension parsing.
CVE-2019-13628 (currently assigned-only): potential leak of nonce sizes
when performing ECDSA signing operations. The leak is considered to be
difficult to exploit but it could potentially be used maliciously to
perform a lattice based timing attack.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Rosen Penev [Thu, 8 Aug 2019 19:01:21 +0000 (12:01 -0700)]
bzip2: Update to 1.0.8
It seems bzip2 was abandoned by the author and adopted by the sourceware
people. The last release of bzip2 was from 2010.
Several security bugs were fixed as well as others.
Fixed up PKG_LICENSE to be compatible with SPDX.
Changed URLs to point to the new home.
Added patch that gets rid of deprecated utime function and switches it to
utimensat.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Adrian Schmutzler [Fri, 9 Aug 2019 11:55:43 +0000 (13:55 +0200)]
build: fix indent in image-commands.mk
Convert leading spaces to tab to match rest of the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Sat, 3 Aug 2019 10:30:38 +0000 (12:30 +0200)]
mac80211: Update to version 5.3-rc4-1
The removed patches were applied upstream.
The type of the RT2X00_LIB_EEPROM config option was changed to bool,
because boolean is an invalid value and the new kconfig system
complained about this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 15 Aug 2019 09:30:44 +0000 (11:30 +0200)]
mac80211: Update to version 5.2.8-1
This contains multiple fixes from the upstream kernel.
The removed patch was merged upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 7 Aug 2019 20:13:36 +0000 (22:13 +0200)]
mdadm: Use upstream fix for musl 1.1.23 compile
Fixes:
ba8aeb02eae2 ("mdadm: Fix compile with musl 1.1.23")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 7 Aug 2019 19:37:25 +0000 (21:37 +0200)]
hostapd: Allow CONFIG_IEEE80211W for all but mini variant
This commit will activate CONFIG_IEEE80211W for all, but the mini
variant when at least one driver supports it. This will add ieee80211w
support for the mesh variant for example.
Fixes: FS#2397
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 4 May 2019 12:16:52 +0000 (14:16 +0200)]
hostapd: Remove ROBO switch support
The driver was removed from OpenWrt a long time ago.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Colby Whitney [Mon, 22 Jul 2019 16:16:14 +0000 (10:16 -0600)]
lua5.3: include hpp header
The install was missing the hpp header. Adding that in.
Signed-off-by: Colby Whitney <colby.whitney@luxul.com>
Klaus Kudielka [Sun, 28 Jul 2019 13:54:21 +0000 (15:54 +0200)]
mvebu: sysupgrade: sdcard: fix platform_do_upgrade_sdcard
Unconditionally execute the final case statement, even if the disk layout
changed. This is necessary, to keep the original Turris Omnia flash
instructions working: The disk layout WILL change, when switching from
TurrisOS to OpenWRT. Without updating the uboot environment at the same
time, the user would end up with an unbootable system.
Fixes commit
2e5a0b81ec ("mvebu: sysupgrade: sdcard: keep user added ...")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Jonas Gorski [Fri, 16 Aug 2019 10:24:13 +0000 (12:24 +0200)]
brcm63xx: do not build images for 16 MiB RAM devices by default
OpenWrt will run out of RAM while booting with the default package set,
so let's not provide images that will likely fail. They can still be
built manually through source or IB if needed.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Kevin Darbyshire-Bryant [Fri, 16 Aug 2019 09:05:12 +0000 (10:05 +0100)]
firewall: improve ipset support
Bump to latest git HEAD
509e673 firewall3: Improve ipset support
The enabled option did not work properly for ipsets, as it was not
checked on create/destroy of a set. After this commit, sets are only
created/destroyed if enabled is set to true.
Add support for reloading, or recreating, ipsets on firewall reload. By
setting "reload_set" to true, the set will be destroyed and then
re-created when the firewall is reloaded.
Add support for the counters and comment extensions. By setting
"counters" or "comment" to true, then counters or comments are added to
the set.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
David Bauer [Sun, 11 Aug 2019 21:37:24 +0000 (23:37 +0200)]
lantiq: unify Fritz!Box LED mappings
This commit unifies the LED mapping of the AVM Fritz!Box routers, which
have a combined Power/DSL LED.
With the stock firmware, the Power LED has the following
characteristics:
- Blink when DSL sync is being established
- Solid when DSL sync is present
We can't completely resemble this behavior in OpenWrt. Currently, the
Power LED is completely off, when DSL sync is missing. This is not
really helpful, as a user might have the impression, that he bricked his
device.
Instead, map the Info-LED to the state of the DSL connection.
There is no consistent behavior for the Info-LED in the stock
firmware, as the user can set it's function by himself. The DSL
connection state is one possible option for the Info LED there.
Also use the red Power LED to indicate a running upgrade, in case the
board has a two-color Power LED.
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler [Wed, 14 Aug 2019 22:46:07 +0000 (00:46 +0200)]
ath79: remove SUPPORTED_DEVICES for TP-Link Archer D50 v1
This device has not been supported in ar71xx, so there is no need
for an explicit SUPPORTED_DEVICES entry.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Wed, 14 Aug 2019 22:29:45 +0000 (00:29 +0200)]
ath79: use Power LED as System LED for TL-WR842Nv3
The TP-Link TL-WR842N v3 has a software-controllable Power LED. The WPS
LED is normally only used as a System LED, when the Power LED can't be
controlled by software.
Additionally, the Power LED is also the System LED for this board in
ar71xx.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 12 Aug 2019 23:44:03 +0000 (01:44 +0200)]
ipq40xx: fix AVM NAND caldata extraction
The AVM Fritz!Box 7530 (and probably other AVM IPQ4019 NAND devices)
has it's caldata not stored consistently, but instead at currently
3 known possible offsets.
As we get a non-zero exit code from fritz_cal_extract, simply try all
three possible offsets on both bootloader partitions, until a matching
caldata for each radio is found.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Koen Vandeputte [Mon, 12 Aug 2019 09:52:25 +0000 (11:52 +0200)]
kernel: bump 4.19 to 4.19.66
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 12 Aug 2019 09:30:09 +0000 (11:30 +0200)]
kernel: bump 4.14 to 4.14.138
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 12 Aug 2019 08:10:44 +0000 (10:10 +0200)]
kernel: bump 4.9 to 4.9.189
Refreshed all patches.
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Adrian Schmutzler [Fri, 9 Aug 2019 15:45:13 +0000 (17:45 +0200)]
treewide: convert WiFi caldata size and offset to hexadecimal
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 9 Aug 2019 15:45:12 +0000 (17:45 +0200)]
treewide: convert MAC address location offsets to hexadecimal
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Paul Spooren [Tue, 13 Aug 2019 21:38:17 +0000 (11:38 -1000)]
imagebuilder: fix `make info` for empty SUPPORTED_DEVICES
For x86/64 (maybe more) target the SUPPORTED_DEVICES variable is empty
which causes the `&&` junction to fail, producing a non zero exit code.
Tested-by: Paul Spooren <mail@aparcar.org>
Fixed-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Jonas Gorski [Tue, 13 Aug 2019 10:33:47 +0000 (12:33 +0200)]
build: allow overriding default selection state for devices
Allow overriding the default selection state for Devices, similar to
setting a default for packages.
E.g. by setting DEFAULT to n, they won't be selected by default anymore
when enabling all device in the multi device profile.
This allows preventing images being built by the default config for
known broken devices, devices without enough RAM/flash, or devices not
working with a certain kernel versions.
This does not prevent the devices from being manually selected or images
being built by the ImageBuilder. These devices often still have worth
with a reduced package-set, or as a device for regression testing, when
no better device is available.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Paul Spooren [Mon, 12 Aug 2019 09:08:33 +0000 (23:08 -1000)]
image.mk: remove device_ from manifest filename
The manifest file is based on IMG_PREFIX and PROFILE_SANITIZED, whereas
the latter takes a string like DEVICE_8dev_carambola2 and sanitizes it.
This behaviour results in a useless "device_" profile-prefix in the
device manifest filename. Now uses *subst* to remove that.
Therefore this patch results more consistent device file names:
openwrt-ath79-generic-8dev_carambola2-initramfs-kernel.bin
openwrt-ath79-generic-8dev-carambola2.manifest
openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin
instead of a single file being called
openwrt-ath79-generic-device_8dev-carambola2.manifest
Signed-off-by: Paul Spooren <mail@aparcar.org>