Simon Goldschmidt [Sun, 13 Jan 2019 18:58:40 +0000 (19:58 +0100)]
net: designware: socfpga: adapt to Gen5
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Sat, 16 Feb 2019 13:31:05 +0000 (08:31 -0500)]
Merge tag 'u-boot-imx-2019-02-16' of git://git.denx.de/u-boot-imx
u-boot-imx-2019-02-16
---------------------
- vhybrid: add calibration
- gw_ventana: fixes
- Improve documentation for Secure Boot (HABv4)
- Fix Marvell Switch
- MX6 Sabre, switch to DM
- Fixes for NAND
Tom Rini [Sat, 16 Feb 2019 02:21:28 +0000 (21:21 -0500)]
Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2019.04-rc2
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
Tom Rini [Sat, 16 Feb 2019 01:10:15 +0000 (20:10 -0500)]
Merge tag '2019.01-next' of https://github.com/mbgg/u-boot
- add compute module 3+
- fix 64 bit warning in bmp command
Max Krummenacher [Fri, 1 Feb 2019 15:04:51 +0000 (16:04 +0100)]
imx: cpu.c: give access to reset cause in spl
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Max Krummenacher [Fri, 1 Feb 2019 15:04:50 +0000 (16:04 +0100)]
imx: serial_mxc: disable ri and dcd irq in dte mode
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Marcel Ziswiler [Fri, 1 Feb 2019 15:04:49 +0000 (16:04 +0100)]
ARM: dts: i.MX6Q, i.MX6QDL: fix address/size-cells warnings
This fixes the following warnings:
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/clocks: unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/aips-bus@
02100000/mipi@
021e0000: unnecessary #address-cells/
#size-cells without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02400000/port@2: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02400000/port@3: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02800000/port@2: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02800000/port@3: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tim Harvey [Mon, 4 Feb 2019 21:11:00 +0000 (13:11 -0800)]
imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+)
device-tree paths should never be used that reference node addresses
making an assumption about leading zeros. They should not be there per
the device-tree specification however they have been there until Linux
4.15 when they were removed via kernel commit
8dccafaa281aa1d240a58bbcdff338aec114a021.
This fixes various issues which will occur when using Linux 4.15+
that are being fixed up on a per model per PCB revision basis such as:
- enabling MMC UHS-I on board revisions that support it
- enabling PWM based on hwconfig
- fixing PCIe reset on GW552x
- removing cpu external watchdog reset on boards that do not support it
- populate PCI dt nodes based on PCI scan in order to fix GW16082
interrupt mapping and inject MAC address for PCI based GbE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:59 +0000 (13:10 -0800)]
imx: ventana: gw5904/gw5909: disable RS485
The GW5904/GW5909 have a SP33E multi-protocol serial transceiver which we
want to configure to RS232 by default (by de-asserting RS485_EN)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:58 +0000 (13:10 -0800)]
imx: ventana: add support for GW5901/GW5902
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:57 +0000 (13:10 -0800)]
imx: ventana: add support for GW5909
The GW5909 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW5904 but with half the DRAM loaded
and an additional RS232 transceiver off UART2.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:56 +0000 (13:10 -0800)]
imx: ventana: add support for GW5908
The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:55 +0000 (13:10 -0800)]
imx: ventana: add support for GW5907
The GW5907 is a small single board computer based on the i.MX6DL SoC
with the following peripheral set:
- DDR3 memory (512MB default)
- 1x GigE (i.MX6 FEC)
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:54 +0000 (13:10 -0800)]
imx: ventana: add support for GW5906
The GW5906 is a GW552x with mechanical and power supply connector
differences.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:53 +0000 (13:10 -0800)]
imx: ventana: add i2c detect for all LVDS displays
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:52 +0000 (13:10 -0800)]
imx: ventana: skip nand init for nandless boards
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:51 +0000 (13:10 -0800)]
imx: ventana: add support for Z101WX01 LVDS display
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:50 +0000 (13:10 -0800)]
imx: ventana: add support for GW5905
The GW5905 is single-board tablet computer based on the i.MX6 SoC with the
following peripheral set:
- eMMC flash (boot device)
- microSD expansion
- LVDS display connector for off-board 3D+1C with PWM backlight
and I2C based touch controller
- MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640)
- ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART)
- ublox ZOE-M8Q GPS
- LSM9DS1 9-DOF IMU
- 1x 1-lane miniPCIe socket with USB 2.0
- Gateworks System Controller
- Audio jack with TLV320AIC Audio Codec, Speaker AMP
and TSA227E Headphone detect
- MAX8607 3-mode LED camera flash
- DECT ULE module
- FUSB302 USB-C PD and ISL9238 Battery charger
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:49 +0000 (13:10 -0800)]
imx: ventana: remove setup of I2C3 from SPL
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:48 +0000 (13:10 -0800)]
imx: ventana: do not iomux UART1
The only UART that is garunteed on Ventana boards is UART2 (serial-console).
Remove UART1 pinmux as that it is not consistent across all Ventana boards
and U-Boot doesn't need it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:47 +0000 (13:10 -0800)]
imx: ventana: mv88e61xx change LED configuration
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:25 +0000 (16:40 +0000)]
configs: mx6sabresd: Reduce SPL size by disabling DOS, EXT and EFI support
With DM and FIT enabled in SPL, there is an sram overflow. By disabling
CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and
CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all'
for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:24 +0000 (16:40 +0000)]
board: mx6sabresd: Remove the enet reset gpio handling
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi
and get rid of the enet reset gpio handling from the board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:23 +0000 (16:40 +0000)]
board: mx6sabresd: Remove non-DM code
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabresd board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:22 +0000 (16:40 +0000)]
configs: mx6sabresd: Add DM_SPI_FLASH necessary configs
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:22 +0000 (16:40 +0000)]
board: mx6sabreauto: Remove the non-DM code
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:20 +0000 (16:40 +0000)]
configs: mx6sabreauto: Add DM_SPI_FLASH necessary configs
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:19 +0000 (16:40 +0000)]
mx6sabreauto: Add DM_GPIO support
Add the DM_GPIO related config for mx6sabreauto.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:19 +0000 (16:40 +0000)]
mx6sabresd: Add DM_GPIO support
Add the DM_GPIO related config for mx6sabresd.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:18 +0000 (16:40 +0000)]
configs: mx6sabresd: Add SPL FIT and DM support
Enable all the necessary configs for SPL DM and FIT support for
mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:17 +0000 (16:40 +0000)]
configs: mx6sabreauto: Add SPL FIT and DM support
Enable all the necessary configs for SPL DM and FIT support for
mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:16 +0000 (16:40 +0000)]
arm: dts: Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd]
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit
8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:14 +0000 (16:40 +0000)]
arm: dts: Add all the imx6[q|qp|dl] sabre[auto|sd] u-boot dts[i] files
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:13 +0000 (16:40 +0000)]
board: mx6sabreauto: Add board_fit_config_name_match to support FIT in SPL
This matches one of the following three boards (or fails):
- imx6q-sabreauto
- imx6qp-sabreauto
- imx6dl-sabreauto
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:12 +0000 (16:40 +0000)]
board: mx6sabresd: Add board_fit_config_name_match to support FIT in SPL
This matches one of the following three boards (or fails):
- imx6q-sabresd
- imx6qp-sabresd
- imx6dl-sabresd
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:11 +0000 (16:40 +0000)]
mmc: fsl_esdhc: Fix DM_REGULATOR ifdefs for SPL builds
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:10 +0000 (16:40 +0000)]
configs: imx6sabreauto: Add DM_USB support
Add the DM support for USB. For that, DM_REGULATOR is needed.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:09 +0000 (16:40 +0000)]
configs: imx6sabreauto: Add DM_MMC support
Add DM_MMC config to imx6sabreauto defconfig.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:08 +0000 (16:40 +0000)]
usb: ehci-mx6: Make regulator DM_REGULATOR dependent
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:07 +0000 (16:40 +0000)]
usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGE
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Michal Simek [Thu, 14 Feb 2019 12:14:30 +0000 (13:14 +0100)]
arm64: zynqmp: Create fdtfile from compatible string
distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Venkatesh Yadav Abbarapu [Wed, 14 Nov 2018 11:50:18 +0000 (17:20 +0530)]
arm64: zynqmp: Change the spi-rx-bus-width property to x1
As per the zc1275 design x1 mode is enabled so changing the
spi-rx-bus-width property to x1.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Shubhrajyoti Datta [Mon, 3 Sep 2018 10:16:46 +0000 (15:46 +0530)]
arm64: zynqmp: Fix i2c boot warning
Fix the below warning as the core looks for the compatible
string.
[ 5.198919] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@19
[ 5.207454] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@19
[ 5.216394] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@30
[ 5.224986] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@30
[ 5.233927] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@35
[ 5.242527] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@35
[ 5.263880] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@36
[ 5.272477] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@36
[ 5.281415] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@51
[ 5.290008] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@51
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 14:39:04 +0000 (15:39 +0100)]
arm64: zynqmp: Remove autodetected devices without description
It will never reach mainline that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Amit Kucheria [Thu, 23 Aug 2018 08:53:29 +0000 (14:23 +0530)]
arm64: dts: Fix various entry-method properties to reflect documentation
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit
a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 15:39:51 +0000 (16:39 +0100)]
xilinx: dts: Remove additional empty lines
Trivial fix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mounika Grace Akula [Tue, 9 Oct 2018 15:22:50 +0000 (20:52 +0530)]
arm64: zynqmp: Add reset-on-timeout for all boards and modify default timeout value
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:20 +0000 (00:10 -0400)]
ARM: dts: zynq: correct and improve the model property of dt files
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:19 +0000 (00:10 -0400)]
ARM: dts: zynq: Set correct manufacturer for ZedBoard and MicroZed boards
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 26 Sep 2018 11:36:16 +0000 (13:36 +0200)]
ARM: dts: Use mmc@ instead sdhci@
mmc name is recommended based on devicetree specification.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tim Harvey [Mon, 4 Feb 2019 20:56:52 +0000 (12:56 -0800)]
net: mv88e61xx: fix autonegotiation on ports
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Breno Matheus Lima [Wed, 23 Jan 2019 19:30:16 +0000 (19:30 +0000)]
doc: imx: habv4: Remove secure_boot.txt guide
The secure_boot.txt guide was replaced by mx6_mx7_secure_boot.txt and
mx6_mx7_spl_secure_boot.txt documents.
Both documents covers all steps needed for SPL and non-SPL tagets,
so remove secure_boot.txt file to avoid duplicated content.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Jonathan Gray [Wed, 30 Jan 2019 22:24:44 +0000 (09:24 +1100)]
rpi: add Compute Module 3+
Add Raspberry Pi Compute Module 3+ to list of models, the revision code
is 0x10 according to the list on raspberrypi.org.
v2: Use the same dtb name as CM3 as CM3+ is a drop in replacement
for CM3.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Adam Heinrich [Mon, 31 Dec 2018 11:11:08 +0000 (12:11 +0100)]
cmd: bmp: Make integer-to-pointer cast platform, independent
This patch fixes the int-to-pointer-cast warning on aarch64.
Signed-off-by: Adam Heinrich <adam@adamh.cz>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:30:11 +0000 (19:30 +0000)]
doc: imx: habv4: Move encrypted boot guide
All guides are currently located at doc/imx/habv4/guides/ directory.
Move encrypted_boot.txt document to guides directory.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:30:06 +0000 (19:30 +0000)]
doc: imx: habv4: Add Secure Boot guide for i.MX6 and i.MX7 SPL targets
The current U-Boot implementation includes SPL targets for
some NXP development boards:
- mx6sabreauto_defconfig
- mx6sabresd_defconfig
- mx6ul_14x14_evk_defconfig
- mx6ul_9x9_evk_defconfig
Add additional steps needed to completly secure the
bootloader image.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:29:59 +0000 (19:29 +0000)]
doc: imx: habv4: Add Secure Boot guide for i.MX6 and i.MX7 non-SPL targets
Add HABv4 documentation for non-SPL targets covering the
following topics:
- How to sign an securely boot an u-boot-dtb.imx image.
- How to extend the root of trust for additional boot images.
- Add 3 CSF examples.
- Add IVT generation script example.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:29:53 +0000 (19:29 +0000)]
doc: imx: habv4: Add HABv4 introduction
The HABv4 is supported in i.MX50, i.MX53, i.MX6, i.MX7,
series and i.MX 8M, i.MX8MM devices.
Add an introductory document containing the following topics:
- HABv4 Introduction
- HABv4 Secure Boot
- HABv4 Encrypted Boot
- HAB PKI tree generation
- HAB Fast Authentication PKI tree generation
- SRK Table and SRK Hash generation
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:29:46 +0000 (19:29 +0000)]
doc: imx: habv4: Remove extra hab directory for a cleaner documentation structure
There is no need to have an extra hab directory under doc/imx/.
Habv4 and AHAB documentation can be added directly in doc/imx/ for a
cleaner documentation structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Marcin Niestroj [Sat, 19 Jan 2019 16:06:45 +0000 (17:06 +0100)]
ARM: dts: imx6ul-lite*: add DTS files for liteSOM and liteboard
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Adam Ford [Thu, 17 Jan 2019 13:16:39 +0000 (07:16 -0600)]
MTD: nand: mxs_nand: Allow driver to auto setup ECC in SPL
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Adam Ford [Tue, 15 Jan 2019 17:26:48 +0000 (11:26 -0600)]
net: dm: fec: Fix regulator enable when using DM_REGULATOR
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes:
ad8c43cbcafb ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adam Ford [Sat, 12 Jan 2019 23:32:00 +0000 (17:32 -0600)]
ARM: imx6q_logic: Correct phy fixup for broken ethernet
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Sat, 12 Jan 2019 23:24:52 +0000 (17:24 -0600)]
ARM: imx6q_logic: Enable SPL Booting from NAND
This patch fixes a few values that were incorrect, and this
now lets SPL boot from NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Sat, 12 Jan 2019 12:25:48 +0000 (06:25 -0600)]
MTD: NAND: mxs_nand_init_dma: Make mxs_nand_init_dma static
mxs_nand_init_dma is only referenced from mxs_nand.c. It's not
referenced in any headers or outside code, so this patch
defines it as static.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Thu, 3 Jan 2019 02:36:52 +0000 (20:36 -0600)]
MTD: mxs_nand: Fix BCH read timeout error on boards requiring ECC
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Lukasz Majewski [Wed, 5 Dec 2018 16:04:03 +0000 (17:04 +0100)]
ddr: vybrid: Add calibration code to memory controler's (DDRMC) setup code
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Lukasz Majewski [Wed, 5 Dec 2018 16:04:02 +0000 (17:04 +0100)]
ddr: vybrid: Provide code to perform on-boot calibration
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Wed, 5 Dec 2018 16:04:01 +0000 (17:04 +0100)]
ddr: vybrid: Add DDRMC calibration related registers (DQS to DQ)
This commit provides extra defines needed for DDR memory controller
calibration (read leveling performing).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Tom Rini [Fri, 15 Feb 2019 01:14:51 +0000 (20:14 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- MMC CD pin fix on Orangepi Zero plus
- SPI boot for Olinuxino Lime2-eMMC boards
- Change in dram frequnecy for tbs_a711
Michal Simek [Wed, 13 Feb 2019 12:33:32 +0000 (13:33 +0100)]
arm64: zynqmp: Remove board config files
All options have been moved to Kconfig and there is no need to have
board header files. Mini configurations require them that's why they are
still there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 13:00:06 +0000 (14:00 +0100)]
arm64: zynqmp: Remove SPD related configurations
SPD autodetection hasn't been enabled that's why there is zero size
difference if that options are enabled/disabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 12:46:41 +0000 (13:46 +0100)]
arm64: zynqmp: Fix logic around CONFIG_ZYNQ_SDHCI
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 22 Jan 2019 14:55:46 +0000 (15:55 +0100)]
xilinx: common: Remove !DM_i2C code for reading mac from eeprom
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Tue, 22 Jan 2019 11:50:12 +0000 (12:50 +0100)]
i2c: Remove ancient zynq_i2c driver
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
Michal Simek [Fri, 18 Jan 2019 08:09:40 +0000 (09:09 +0100)]
arm64: zynqmp: Remove addresses for i2c controllers
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Fri, 18 Jan 2019 08:10:39 +0000 (09:10 +0100)]
arm64: zynqmp: Switch all platforms to DM_I2C
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Tue, 22 Jan 2019 11:48:47 +0000 (12:48 +0100)]
ARM: zynq: Remove addresses for i2c controllers
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Tue, 22 Jan 2019 13:43:04 +0000 (14:43 +0100)]
ARM: zynq: Convert dlc20 and zc70x board to DM_I2C
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Tue, 22 Jan 2019 13:12:54 +0000 (14:12 +0100)]
ARM: zynq: Convert Syzygy to DM_I2C
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Siva Durga Prasad Paladugu [Mon, 4 Feb 2019 10:48:29 +0000 (16:18 +0530)]
arm64: versal: Add mini configuration for Versal
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 28 Jan 2019 10:12:41 +0000 (11:12 +0100)]
arm64: versal: Move IOU_SWITCH_DIVISOR0 to Kconfig
Move hardcoded IOU_SWITCH_DIVISOR0 to Kconfig to be able to set it up
for different platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 28 Jan 2019 10:08:00 +0000 (11:08 +0100)]
arm64: versal: Remove one level of indentation in board_early_init_r()
Simplify code indentation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Thu, 31 Jan 2019 11:58:13 +0000 (17:28 +0530)]
arm64: versal: Define distro boot commnads for qspi ospi and mmc
This patch adds distro boot commands for qspi, ospi and mmc.
The distro boot commands now reads the script from flash offset
of 63.5MB for qspi and ospi and executes it. For mmc its same
as generic distro boot command. As either one of the qspi or ospi can
exist on hardware, defined a single distroboot command as xspi
that works for both.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards for qspi, ospi for now.
512kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 28 Jan 2019 09:47:33 +0000 (10:47 +0100)]
arm64: versal: Disable showing information about console
There is no need to see this info. It is just wasting of space/time.
It saves 308Bytes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Fri, 25 Jan 2019 11:36:06 +0000 (17:06 +0530)]
arm: zynq: Update boot_targets based on bootmode
Update boot_targets based on bootmode to run corresponding
distroboot command first.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Fri, 25 Jan 2019 11:36:05 +0000 (17:06 +0530)]
arm: zynq: Define distro boot commnads for qspi, nand and nor
This patch adds distro boot commands for qspi, nand and nor.
The distro boot commands now reads the script from flash offset
of 15.75MB and executes it.
Setup default location via script_offset_f to 15.75MB to match the most
xilinx reference boards for qspi, nand and set the same using
script_offset_nor to 0xE2EC0000 for nor.
256kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 29 Nov 2018 07:48:28 +0000 (08:48 +0100)]
spi: zynqmp_gqspi: Enable versal compatible string
Trivial patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Tue, 8 Jan 2019 16:17:29 +0000 (21:47 +0530)]
arm64: versal: Add mini eMMC configuration
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 17 Jan 2019 08:22:37 +0000 (09:22 +0100)]
arm64: versal: Enable different ethernet phy for virt platform
This platform is going to become generic that's why it is necessary also
enable different PHY vendors.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Tue, 8 Jan 2019 16:17:26 +0000 (21:47 +0530)]
arm64: versal: Add new Kconfig SYS_MEM_RSVD_FOR_MMU
This patch adds new config option which is used for
reserving a specific memory for MMU Table and in this
case we are using TCM for that purpose.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 28 Jan 2019 07:40:50 +0000 (08:40 +0100)]
ARM: zynq: Convert Antminer to OF_SEPARATE
Convert board from OF_EMBED to OF_SEPARATE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 21 Jan 2019 15:29:07 +0000 (16:29 +0100)]
xilinx: common: Add support for DM_I2C zynq_board_read_rom_ethaddr()
It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.
For example:
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 21 Jan 2019 14:25:02 +0000 (15:25 +0100)]
xilinx: Move zynq_board_read_rom_ethaddr to shared location
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Thu, 24 Jan 2019 06:02:04 +0000 (11:32 +0530)]
arm64: zynqmp: Define distro boot commnads for qspi and nand
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 3 Jan 2019 12:58:27 +0000 (13:58 +0100)]
ARM: zynq: Run distribution boot commands first
This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.
QSPI, NAND distribution boot command will be added later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 13 Feb 2019 12:12:29 +0000 (07:12 -0500)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2019-02-13
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
Heinrich Schuchardt [Sat, 9 Feb 2019 21:23:48 +0000 (22:23 +0100)]
efi_loader: fix EFI_FILE_PROTOCOL.GetInfo()
We check the existence of files with fs_exist(). This function calls
fs_close(). If we do not set the active block device again fs_opendir()
fails and we do not set the flag EFI_FILE_DIRECTORY. Due to this error the
`cd` command in the EFI shell fails.
So let's add the missing set_blk_dev(fh) call.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Sun, 10 Feb 2019 10:11:26 +0000 (11:11 +0100)]
lib: vsprintf: avoid overflow printing UTF16 strings
We have to ensure while printing UTF16 strings that we do not exceed the
end of the print buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 11 Feb 2019 14:24:00 +0000 (15:24 +0100)]
efi_loader: Make HII a config option
Heinrich ran into issues with HII and iPXE which lead to #SErrors on
his Odroid-C2 system. We definitely do not want to regress just yet,
so let's not expose the HII protocols by default.
Instead, let's make it a config option that people can play with
This way, we can stabilize the code in tree without breaking any
users.
Once someone figures out, why this breaks iPXE (probably a NULL
dereference), we can enable it by default.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
---
v1 -> v2:
- Remove HII selftest as well
v2 -> v3:
- Make config option
projects / oweals / u-boot.git / log