usb: xhci-rcar: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

pinctrl: rmobile: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

net: ravb: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>

mmc: uniphier-sd: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

gpio: rcar: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

clk: renesas: Add R8A77965 M3N entries

Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Add R8A77965 M3N IDs

Add CPU and PRR IDs for R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

Merge branch 'master' of git://git.denx.de/u-boot-sh

Merge tag 'xilinx-kconfig-for-v2018.03' of git://denx.de/git/u-boot-microblaze

Xilinx Kconfig changes for v2018.03

- Moving some macros to Kconfig

# gpg: Signature made Thu 01 Mar 2018 10:45:58 AM EST using DSA key ID 294A0C21
# gpg: Good signature from "Michal Simek <monstr@monstr.eu>"
# gpg:                 aka "Michal Simek (Xilinx) <michals@xilinx.com>"
# gpg:                 aka "Michal Simek (Xilinx) <michal.simek@xilinx.com>"

mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ

This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ

This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Added Kconfig support for CONFIG_XILINX_GPIO

This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1

This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and
CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET

This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfig

This patch enabled CONFIG_SYS_I2C_ZYNQ in the respective
defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPL

This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the
values over to the defconfigs.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

fpga: Added Kconfig support for FPGA_SPARTAN3

This patch added Kconfig support for FPGA_SPARTAN3 and migrates the
values over to the defconfigs.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

Merge git://git.denx.de/u-boot-net

Kconfig: cmd: Make networking command dependent on NET

Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Makefile: add u-boot-spl.srec target

The u-boot-spl.srec is needed for some platforms, add target to generate this file.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-elf.srec on Gen3

The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs,
conveniently generate this file.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Makefile: add u-boot-elf.srec target

The u-boot-elf.srec is needed for some platforms, add target to generate this file.

Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: socfpga: cyclone5: Enable Macronix flash support

Enable Macronix flash support for Cyclone5 SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>

net: phy: smsc: Add SMSC LAN8741 support

Signed-off-by: Arno Steffens <star@gmx.li>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: e1000: Fix e1000_igb semaphore handling

Fix commit f1bcad22dd19 ("net: e1000: add support for writing to
EEPROM").

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

NET: designware: fix clock enable

After commit ba1f966725223 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.

Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.

If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.

Fix it.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

phy: Fix style violations

Fix some style violations in the generic PHY management code.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

cmd: mdio: Fix style violations

Fix some style violations in the MDIO command.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

net: phy: marvell 88e151x: Fix handling of bare RGMII interface type

Commit 68e6ecadc551 ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.

Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: marvell: Fix style violations

Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

net: tsec: Make live-tree compatible

Make the tsec ethernet driver compatible with a live device tree.

Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

net: tsec: Fix memory leak in error path

tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.

Free the device structure in the error case.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: tsec: Fix style violations

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

ARM: dts: rmobile: Import proper DTS for H2 Stout

Replace the placeholder DTS for R8A7790 H2 Stout with a proper
DTS from Linux next .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 board

Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.

Signed-off-by: Marek Vasut <marex@denx.de>

Merge git://git.denx.de/u-boot-mmc

mmc: omap_hsmmc: use a default 52MHz max clock rate if none is specified

mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

mmc: omap_hsmmc: make it possible to compile out ADMA support

Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

mmc: omap_hsmmc: compile out write support if not needed

This reduces the size of the binary by about 196 bytes.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

mmc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_plat

The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.

This saves around 740 bytes for the am335x_evm SPL.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-rockchip

Merge git://git.denx.de/u-boot-imx

bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDR

Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig.  We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use.  We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig.  In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files.  The previous default
only applied in some cases, even on a specific SoC family.

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

imx: spl: Partially revert "spl: eMMC/SD: Provide one __weak spl_boot_mode() function"

Commit d695d6627803 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:

U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0

Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.

Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>

rockchip: clk: rk3399: handle set_rate/get_rate for PLL_PPLL

The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.

In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.

Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.

References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

rockchip: rk3288: Fix wrong TPL_TEXT_BASE

TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So  0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.

Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff

So, Fix the TEXT_BASE for proper aligned address 0xff704000

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

rockchip: rk3288: Add TPL_LDSCRIPT

Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

rockchip: clk: rk3368: handle clk_enable requests for GMAC

Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
    enabled (no actual action is necessary as the gates are open
    after reset)

References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

rockchip: clk: rk3399: handle clk_enable requests for GMAC

Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.

References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

ARM: dts: i.MX6QDL: icore-rqs: Fix eMMC detection during SPL

usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Remove CONFIG_SYS_BOOTCOUNT_SINGLEWORD

Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's
no remaining uses of it left.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Migrate CONFIG_BOOTCOUNT_ALEN to Kconfig

Convert CONFIG_BOOTCOUNT_ALEN to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Migrate generic bootcount to Kconfig

Make generate boot counter selected in the same way as other boot count
drivers

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Integrate AT91 bootcount driver

Integrate Boot counter for Atmel AT91SAM9XE into Kconfig

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Convert CONFIG_BOOTCOUNT_EXT to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_EXT

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Convert CONFIG_BOOTCOUNT_I2C to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_I2C

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_BOOTCOUNT_RAM to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_RAM

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_BOOTCOUNT_ENV to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_ENV

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_BOOTCOUNT_AM33XX to Kconfig

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_AM33XX

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Prepare for multiple bootcount drivers

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>

Merge CONFIG_BOOTCOUNT and CONFIG_BOOTCOUNT_LIMIT

CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with
CONFIG_BOOTCOUNT_LIMIT

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Ian Ray <ian.ray@ge.com>

Merge git://git.denx.de/u-boot-video

Remove config_distro_defaults.h

With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

rockchip: video: update MAINTAINERS

The video drivers (VOP, HDMI encoder, LVDS encoder, MIPI encoder) for
Rockchip SOCs are self-contained and are mainly impacted by other
changes in the architecture support (e.g. pinctrl, clocking, etc).

Let's add these to the list of files maintained as part of the
Rockchip port.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>

rockchip: video: rk_vop: migrate to livetree

This migrates rk_vop (the shared functions used by multiple VOP
mini-drivers) to be compatible with a live tree.

Unfortunately, there's
(i)  a lot of tree traversal needed for a VOP (as each active VOP
     vnode references back to the endpoints in the encoders and vice
     versa) to configure the connection between VOPs and encoders;
(ii) the DTS binding is not too sane and one needs to walk a node's
     parents (the original code just assumed that the device would
     live 3 levels above the property linked through a phandle) until
     a UCLASS_DISPLAY device can be found.

As part of the migration, the code for finding the enclosing display
device has been changed to not assume a specific depth of nesting
(i.e. we walk until we reach the root or find a matching device) and
to use the newly introduced (in the same series) ofnode_get_parent()
function.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>

rockchip: video: rk_hdmi: migrate to livetree

The rk_hdmi (shared functions for multiple HDMI mini-drivers) has been
using devfdt_get_addr() to read the HDMI controller's IO base address.
This will cause a failure with a live tree.

This changes the driver to use dev_read_addr() which is safe both for
flat trees and live trees.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>

core: add ofnode_get_by_phandle() api

We need to get ofnode from a phandle, add interface to support
both live dt and fdt.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

core: ofnode: add ofnode_get_parent function

The Rockchip video drivers need to walk the ofnode-parrents to find
an enclosing device that has a UCLASS_DISPLAY driver bound.  This
adds a ofnode_get_parent()-function that returns the parent-node.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>

Merge git://git.denx.de/u-boot-sh

Merge git://git.denx.de/u-boot-usb

config_whitelist: remove false-positive CONFIG options

U-Boot pulled in several core makefiles from Linux.  The following
are not used in U-Boot:

  - CONFIG_DEBUG_SECTION_MISMATCH
  - CONFIG_FTRACE_MCOUNT_RECORD
  - CONFIG_GCOV_KERNEL
  - CONFIG_GCOV_PROFILE_ALL
  - CONFIG_KASAN
  - CONFIG_MODVERSIONS

We can remove the unused code if we like. (although it will get the
scripts out of sync)

CONFIG_BOOM and CONFIG_HIS_DRIVER are just mentioned in the comment
block of scripts/basic/fixdep.c

CONFIG_SHELL is not configuration, but a variable for internal-use.
It is just a historical misnomer in Kbuild.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

omap3_logic: Fix Environmental location

For the omap3_logic boards, the environment is always in NAND.
This removes the ENV_IS_IN_FAT flag to eliminate the extra chatter.

Signed-off-by: Adam Ford <aford173@gmail.com>

sf: Add ISSI IS25LP256 entry

Add entry for ISSI IS25LP256 part.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@openedev.com>

Makefile: Don't mess with .text section location for selected arches

Most of architectures have .text section situated in the very beginning
of U-Boot binary and thus it is very logical that CONFIG_SYS_TEXT_BASE
is used on final linkage step to specify where U-Boot gets linked to.

For that we pass the following construction to the LD:
---------------------------->8-----------------------
xxx-ld ...  -Ttext $(CONFIG_SYS_TEXT_BASE) ...
---------------------------->8-----------------------

But there could be exceptions. For example:
 1. In case of ARCv2 we want to put vectors table in its own section
    .ivt in front of .text section which means we need either add an
    offset to CONFIG_SYS_TEXT_BASE to compensate for .ivt or don't
    pass "-Ttext" to the LD at all and specify link base in linker
    script directly.

 2. Some architectures even though have .text section in the very
    beginning of the U-Boot image still use different symbols to
    specify link-base:
       * NIOS2: CONFIG_SYS_MONITOR_BASE (which I really like because
         that exactly what makes sense - where out image starts but not
         beginning of its .text section which just happened to match the
         whole image beginning)
       * EXTENSA: CONFIG_SYS_TEXT_ADDR
       * X86: Which doesn't use CONFIG_SYS_MONITOR_BASE in case of EFI
         otherwise sets explicit link base in u-boot.lds

I think that's good to allow for flexibility and don't require each and
every architecture or even platform to specify CONFIG_SYS_TEXT_BASE as well
as use it to set .text section location.

So let's only pass "-Ttext xxx" for those architectures who don't set
link-base explicitly in their linker scripts.

This patch iaddresses comments for previously sent
https://patchwork.ozlabs.org/patch/867540/.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>

arm64: show_regs: Dump the LRs HW values

These were dropped in [1], after relocation, for their values offset by
reloc_off.
Unconditionally show the HW values and add a '(reloc)' hint for the
offset values showed after relocation.
Also, the LRs' dumps are now formatted the same way the other regs' are.

[1] Commit 082693f4 ("arm64 :show_regs: show the address before relocation")

Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>

tools/kwbimage: fix LibreSSL build

Fix build after addition of RSA_get0_key() to LibreSSL.
Patch from Theo Buehler and Stuart Henderson.

Signed-off-by: Theo Buehler <tb@openbsd.org>
Signed-off-by: Stuart Henderson <sthen@openbsd.org>

net: Remove Xilinx ll_temac driver

ll_temac driver was used by Xilinx Microblaze big endian and
Xilinx ppc405/ppc440 SoCs.

ppc support was removed by: "powerpc: remove 4xx support"
(sha1: 98f705c9cefdfdba62c069821bbba10273a0a8ed)
and Microblaze BE is not tested for a long time that's why this driver
can be removed because none is going to updated it to DM anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: am335x_evm_usbspl: Add CONFIG_SPL_NET_VCI_STRING

Add CONFIG_SPL_NET_VCI_STRING to enable USB-Ethernet boot mode
support.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

fdt: Fixup only valid memory banks

Memory banks with address 0 and size 0 are empty and should not be
passed to the OS via device tree.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

ns16550: Fix mem mapped endian check

Do a explicit check for CONFIG_SYS_BIG_ENDIAN and
CONFIG_SYS_LITTLE_ENDIAN to avoid errors on platforms where both
are undefined (x86).

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

pci: Fix decode regions for memory banks

Since memory banks may not be located behind each other we need to add
them separately.

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

defconfig: k2x_hs_evm: Re-enable TI_SECURE_DEVICE in HS K2x parts

These got removed in config re-syncs due to a Kconfig bug. Add these
back here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

env: Fix missed getenv_ulong to env_get_ulong conversion

This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.

Fixes: bfebc8c965e4 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: Kconfig: Move TI_SECURE_DEVICE to a common area

TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.

Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.

Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.

Fixes: a93fbf4a7892 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

xtensa: clean up CONFIG_SYS_TEXT_ADDR

Drop CONFIG_SYS_MEMORY_TOP. Rename CONFIG_SYS_TEXT_ADDR to
XTENSA_SYS_TEXT_ADDR.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>

configs: Re-sync with CONFIG_DISTRO_DEFAULTS

A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS.  As they plainly intended to, set that flag and
re-sync config files.

Signed-off-by: Tom Rini <trini@konsulko.com>

mmc: fix off-by-one bug in mmc_startup_v4()

MMC card with EXT_CSD_REV value 9 will trigger off-by-one
bug while accessing mmc_versions array. The patch fix that.

Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>

mmc: Drop unnecessary case for mmc_probe()

Drop the unnecessary empty function case for mmc_probe().

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

mmc: uniphier-sd: Add compatible strings for RCar Gen2

Add DT compatible strings for RCar Gen2 SoCs, so that this driver
can bind with them. Unlike Gen3, which uses 64bit FIFO, the Gen2
uses 16bit FIFO.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

sh: Do not provide strncmp

With modern GCC, we get warnings such as:
cmd/jffs2.c: In function 'mtdparts_init':
arch/sh/include/asm/string.h:110:38:
warning: array subscript is above array bounds [-Warray-bounds]
   : "0" (__cs), "1" (__ct), "r" (__cs+__n)
                                  ~~~~^~~~

This results in a small size reduction as well.

Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

imx6q: engicam: Use SPL_LOAD_FIT for MMC boards

Currently SPL_LOAD_FIT is unable to boot from nand on
i.MX6QDL platform, so enable only for MMC boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx6: engicam: Drop SPL_EXT_SUPPORT

i.MX6 boards still using raw MMC write for SPL and
u-boot-dtb.img along with Falcon mode configurations,
so drop filesystem based write through SPL_EXT_SUPPORT.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx6ul: engicam: Drop isiot-mmc defconfig

Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arm: imx: hab: Define HAB_RVT_BASE according to the processor version

Currently the following devices are using a different definition for ROM
Vector Table addresses:

- i.MX6DQP =  All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2

There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.

More details about RVT base address can be found on processors Reference
Manual and in the following documents:

EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison

EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>