powerpc/mpc85xx: Add workaround to enable TDM on T1040

This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM

Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

powerpc/B4420: Fixed incomplete handling for 0x9d serdes2

Crossbars and IDT were not getting configured for Serdes2 protocol
0x9d for B4420.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

powerpc/serdes: Add the workaround for erratum A-007186

SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.

This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.

This workaround is valid for B4, T4 and T2 platforms, so
added in their config.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>

powerpc/mpc85xx: Add workaround for DDR erratum A004508

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

powerpc/t2080: add serdes2 protocol 0x27

Add a new serdes2 protocol 0x27.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

powerpc/espi: remove 80us delay to improve transfer performance

Replace 80 mircoseconds delay with polling flag ESPI_EV_TXE.

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

powerpc/t4rdb: Add alternate serdes protocols to align with A-007186

A-007186: SerDes PLL is calibrated at reset. It is possible
for jitter to increase and cause the PLL to unlock when the
temperature delta from the time the PLL is calibrated exceeds
+56C/-66C when using X VDD of 1.35 V (or +70C/-80C when using
XnVDD of 1.5 V). No issues are seen with LC VCO. The protocols
only using Ring VCOs are impacted.

Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring
VCO, this need to use alternate serdes protocols. Alternate
option has the same functionality as the original option; the
only difference being LC VCO rather than Ring VCO.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

board/t2080qds: some update for ddr

- add support for 2nd DIMM slot.
- make it work with DIMM which is less than 2GB.

Verified with two 2GB UDIMM MT9JSF25672AZ-2G1K1 in two DIMM slots.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

powerpc/t4qds: Add alternate serdes protocols to align with A-007186

A-007186: SerDes PLL is calibrated at reset. It is possible for jitter to
increase and cause the PLL to unlock when the temperature delta from the
time the PLL is calibrated exceeds +56C/-66C when using X VDD of 1.35 V
(or +70C/-80C when using XnVDD of 1.5 V). No issues are seen with LC
VCO. Only the protocols using Ring VCOs are impacted.

Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring VCO, this need
to use alternate serdes protocols. The alternate option has the same
functionality as the original option; the only difference being LC VCO
rather than Ring VCO.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

board/t208x: update t2080qds/t2080rdb for errata A-007186

As errata A-007186, we need to use the alternate serdes
protocol instead of those impacted protocols.

- add support for serdes protocols: 0x1b, 0x50, 0x5e,
  0x64, 0x6a, 0xd2, 0x67, 0x70.
- update t2080_rcw.cfg to adapt to new rcw_66_15 for
  t2080qds and t2080rdb.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Merge branch 'master' of git://git.denx.de/u-boot-avr32

powerpc: hiddendragon: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: debris: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: kvme080: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: ep8248: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: ispan: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: rattler: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: zpc1900: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: mpc8260ads: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

powerpc: adder: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC8xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

PPC4xx: Remove quad100hd board

The quad100hd has been unmaintained and dead ever since it's been
added some 6 years ago.  Remove it.

Also update README.scrapyard and insert some commit IDs for removed
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Gary Jennejohn <gljennjohn@googlemail.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

main: Avoid unncessary strdup()/free()

It doesn't seem necessary to use memory allocation in this code. The setenv()
will make a copy anyway.

Signed-off-by: Simon Glass <sjg@chromium.org>

main: Make the execution path a little clearer in main.c

bootdelay_process() never returns in some circumstances, whichs makes the
control flow confusing. Change it so that the decision about how to execute
the boot command is made in the main_loop() code, so it is easier to follow.
Move CLI stuff to cli.c.

Signed-off-by: Simon Glass <sjg@chromium.org>

main: Hide the hush/simple details inside cli.c

Move these details from main (which doesn't care which parser is used) to
cli.c where they belong.

Signed-off-by: Simon Glass <sjg@chromium.org>

Simplify the main loop

The main loop is easier to follow if the code is grouped into separate
functions. Make this change, so that main_loop() is easier to read.

Signed-off-by: Simon Glass <sjg@chromium.org>

m68k: powerpc: Clean up do_mdm_init

This code seems unnecessarily complex. We really just need to check the
global_data. Now that is it all in one place, and not arch-specific, this
is pretty easy.

Signed-off-by: Simon Glass <sjg@chromium.org>

Rename bootretry functions and remove #ifdefs

Add a bootretry_ prefix to these two functions, and remove the need for
the #ifdef around everything (it moves to the Makefile).

Signed-off-by: Simon Glass <sjg@chromium.org>

Move bootretry code into bootretry.c and clean up

This code is only used by one board, so it seems a shame to clutter up
the readline code with it. Move it into its own file.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move command line API into cli.c

We now have a single entry point to the CLI, whether simple or hush. Put
this in its own file.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move autoboot code to autoboot.c

The autoboot code is complex and long. It deserves its own file with
a simple interface from main.c.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add cli_ prefix to readline functions

This makes it clear where the code resides.

Signed-off-by: Simon Glass <sjg@chromium.org>

Split out simple parser and readline into separate files

It doesn't make sense to have the simple parser and the readline code
all in main. Split them out into separate files.

Signed-off-by: Simon Glass <sjg@chromium.org>

move CLI prototypes to cli.h and add comments

Move the CLI prototypes from common.h to cli.h as part of an effort to
reduce the size of common.h.

Signed-off-by: Simon Glass <sjg@chromium.org>

Rename hush to cli_hush

Hush is a command-line interpreter, so rename it to make that clearer.

Signed-off-by: Simon Glass <sjg@chromium.org>

Remove unnecessary use of hush header file

Some files include hush.h but don't actually use it. Remove this where
possible.

Signed-off-by: Simon Glass <sjg@chromium.org>

Merge branch 'master' of git://git.denx.de/u-boot-arc

tb100 - add Abilis TB100 board

Development board for headless gateway platform from Abilis Systems.
Initial commit with working UART and DW GMAC.

For now with generic Ethernet PHY due to problems in Realtek PHY driver.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Pierrick Hascoet <pierrick.hascoet@abilis.com>

Prepare v2014.07-rc2

Signed-off-by: Tom Rini <trini@ti.com>

dm: rename device struct to udevice

using UBI and DM together leads in compiler error, as
both define a "struct device", so rename "struct device"
in include/dm/device.h to "struct udevice", as we use
linux code (MTD/UBI/UBIFS some USB code,...) and cannot
change the linux "struct device"

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>

ARM: at91sam9m10g45ek: add mmc environment configuration support

In this configuration the environment will save in file: uboot.env of
mmc card.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: at91sam9m10g45ek: enable mci0 support

Also we enable the mmc command in configuration file.

As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: at91: remove redundant ARM926EJS definition in board config files

As at91 board config file will include the SoC header, so we can remove
the ARM926EJS definition in board config files.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

at91: remove redundant AT91FAMILY definition in board config file

Now the AT91FAMILY is already defined in the at91 SoC header. The at91
board config file will include the SoC header file.

So we can remove the redundant AT91FAMILY definition in at91 board
config files.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: at91sam9x5: define the AT91FAMILY and ARM926EJS in SoC header

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: at91: remove AT91X40 macro since it is not use any more

The at91x40.h is not exist. So we remove it.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

sama5d3xek: enable PMECC header generation

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>

arm:at91: enable ROM loadable atmel image

For sama5d3xek we need to modify the SPL image for correct detection by ROM
code.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Bo Shen <voice.shen@atmel.com>

mkimage: add atmelimage

The new atmelimage converts a machine code BLOB to bootable ROM image. Atmel
ROM has no sophisticated image format, it only checks the first 7 ARM vectors.
The vectors can contain valid B or LDR opcodes, the 6'th vector contains the
image size to load.

Additionally the PMECC header can be written by the atmelimage target. The
parameters must be given via the -n switch as a coma separated list. For
example:

mkimage -T atmelimage \
 -n usePmecc=1,sectorPerPage=4,sectorSize=512,spareSize=64,eccBits=4,eccOffset=36 \
 -d spl/u-boot-spl.bin boot.bin

A provided image can be checked for correct header setup. It prints out the
PMECC header parameters if it has one and the 6'th interrupt vector content.

---8<---
Image Type: ATMEL ROM-Boot Image with PMECC Header
PMECC header
====================
eccOffset:        36
sectorSize:      512
eccBitReq:         4
spareSize:        64
nbSectorPerPage:   4
usePmecc:          1
====================
6'th vector has 17044 set
--->8---

A SPL binary modified with the atmelimage mkimage target was succesfully
booted on a sama5d34ek via MMC and NAND.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Heiko Schocher <hs@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>

corvus: remove unneeded CONFIG_AT91_LEGACY

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Heiko Schocher <hs@denx.de>

mmc: atmel_mci: fix print incorrect buffer content for debug

Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix checkpatch line length warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

gpio: at91: add sanity check for the NULL pointer

We need check the NULL pointer as at91_pio_get_port() may return NULL.

Also print a error message when at91_pio_get_port() failed otherwise we
cannot notice the failure.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: at91sam9x5ek: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: at91sam9m10g45ek: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: sama5d3_xplained: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: sama5d3xek: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: enable SPL on sama5d3_xplained board

It supports boot from NAND and SD/MMC card.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

ARM: atmel: switch to main crystal osc for SPL boot

If without switch to main crystal oscillator, the sama5d3 SoC will
use internal on chip RC oscillator.
In order to get better accuracy, switch to main crystal oscillator.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

atngw100mkii: add missing CONFIG_SYS_TEXT_BASE

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>

net/designware: Make DMA burst length configurable and reduce by default

The correct value for this setting can vary across SoCs and boards, so make it
configurable.

Also reduce the default value to 8, which is the same default as used in the
Linux driver.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>

net/designware: reorder struct dw_eth_dev to pack more efficiently.

On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote:
> The {r,t}xbuffs fields also need to be aligned. Previously this was done
> implicitly because they immediately followed the descriptor tables. Make this
> explicit and also move to the head of the struct.

Looks like I managed to not actually commit the move of the field to the
head of the struct! v3.1 follows....

Ian.

8<------------

>From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Thu, 1 May 2014 19:45:15 +0100
Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more
 efficiently.

The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could
be 256 or even larger. That means there is a potentially huge hole in the
struct before those fields, so move them to the front where they are better
packed.

Moving them to the front also helps ensure that so long as dw_eth_dev is
properly aligned (which it is since "net/designware: ensure device private data
is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids
having to worry too much about compiler specifics.

The {r,t}xbuffs fields also need to be aligned. Previously this was done
implicitly because they immediately followed the descriptor tables. Make this
explicit and also move to the head of the struct.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>

net/designware: ensure cache invalidations are aligned to ARCH_DMA_MINALIGN

This is required at least on ARM.

When sending instead of simply invalidating the entire descriptor, flush
as little as possible while still respecting ARCH_DMA_MINALIGN, as
requested by Alexey.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>

net/designware: ensure device private data is DMA aligned.

struct dw_eth_dev contains fields which are accessed via DMA, so make sure it
is aligned to a dma boundary. Without this I see:
    ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Marek Vasut <marex@denx.de>

sunxi: non-FEL SPL boot support for sun7i

Add support for booting from an MMC card.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>

sunxi: mmc support

On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG

> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?

It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...

> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.

...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.

> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>

Thanks!

8<---------------------------------

>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support

This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.

Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>

sunxi: add gmac Ethernet support

Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i)
processors. Enable for the Cubietruck.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>

sunxi: add support for Cubietruck booting in FEL mode

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>

sunxi: add sun7i cpu, board and start of day support

This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>

sunxi: add sun7i dram setup support

This patch adds DRAM initialisation support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>

sunxi: add sun7i pinmux and gpio support

This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>

sunxi: add sun7i clocks and timer support.

This patch adds the basic clocks and timer support for the Allwinner A20
(sun7i) processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.

Some of the code here is common to multiple sunxi subarchtectures, hence files
are named sun4i which is the earliest similar variant.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>

boards.cfg: update highbank maintainer email

My Calxeda email is gone, so update my email address.

Signed-off-by: Rob Herring <robh@kernel.org>

arm: vf610: add DDR_SEL_PAD_CONTR register

Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM
issues with newer silicon (1.1). This register was added in revision
4 of the Vybrid Reference Manual.

Signed-off-by: Stefan Agner <stefan@agner.ch>

Arm64 fix a bug of vbar_el3 initialization

Signed-off-by: David Feng <fenghua@phytium.com.cn>

ARM: highbank: convert to generic board

Enable CONFIG_SYS_GENERIC_BOARD on highbank.

Signed-off-by: Rob Herring <robh@kernel.org>

lsxl: rework boot scripts

Move addresses for kernel, ramdisk and fdt blob to own variables. Add dtb
blob loading to all existing boot scripts, dtb filenames were taken from
vanilla kernel. Introduce new boot script bootcmd_legacy, which only loads
a kernel and a ramdisk. Make this the default boot script. This should also
restore the behaviour of the original bootloader.

Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Michael Walle <michael@walle.cc>

lsxl: use 64bit for LBA48 to support 4 TB drives

Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Michael Walle <michael@walle.cc>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

compulab: eeprom: enable any i2c driver

Make the common eeprom library available for any I2C driver.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

cm-t54: add environment partition runtime detection

Add environment partition runtime detection callback.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

cm-t54: add EEPROM support and MAC address handling

cm-t54 Eth MAC address is stored in onboard EEPROM.
Add EEPROM support and setup stored Eth MAC address.

If EEPROM does not contain a valid MAC, then generate it from the
processor ID code (reference code is taken from OMAP5 uEvm board file).

Modify Device Tree blob MAC address field with retrieved data.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

cm-t54: add cm-t54 board support

Add cm-t54 board directory, config file. Enable build.

Basic support includes:

Serial console
SD/MMC
eMMC
USB
Ethernet

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

am33xx: report silicon revision instead of code

As revision code 1 is for silicon revision 2.0, it is easily confused with
silicon revision 1.0.

Device type report also reworked in same style.

Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>

ARM: OMAP: Fix omap_sdram_size calculation

Last section of DMM is used for trapping tiler unmapped sections.
Corresponding trap_size should be deducted from total SDRAM size
only if trap section is overlapping with available SDRAM
based on DMM sections. Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm, am33xx: Enable CONFIG_SYS_GENERIC_BOARD for siemens boards

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Tested-by: Samuel Egli <samuel.egli@siemens.com>

omap4: duovero: Add Gumstix DuoVero machine.

This adds the Gumstix DuoVero machine [1].  This is a OMAP4430-based
computer-on-module (COM aka SOM) that can be mounted on various
expansion boards with different peripherals.

[1] https://store.gumstix.com/index.php/category/43/

Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Rename gpmc_enable_gpmc_cs_config to gpmc_enable_gpmc_net_config]
Signed-off-by: Tom Rini <trini@ti.com>

armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_context

The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same.  In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.

Cc: Sricharan R. <r.sricharan@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

compulab: eeprom: add default eeprom address

Add default eeprom address setting.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

ARM: DRA7xx: ctrl: Fix efuse register addresses

Efuse register addresses are wrongly programmed.
Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>

ARM: DRA72x: Update EMIF data

DRA72 has 1GB connected to EMIF1 only. Updating the details.
And also enable WA for BUG0039 only if corresponding EMIF is present.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>

ARM: DRA72x: clocks: Update the hwdata

Adding the prcm, dplls, control module hooks for DRA72x.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>

ARM: DRA72x: volt: Update the pmic offsets

TPS65917 is used in DRA722 evm. Update the address offsets accordingly.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tom Rini <trini@ti.com>

ARM: DRA72x: Add Silicon ID support

Add silicon ID code for DRA722 silicon.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>

ARM: omap: merge GPMC initialization code for all platform

GPMC controller on TI's OMAP SoC is general purpose controller to interface
with different types of external devices like;
 - parallel NOR flash
 - parallel NAND flash
 - OneNand flash
 - SDR RAM
 - Ethernet Devices like LAN9220

Though GPMC configurations may be different for each platform depending on
clock-frequency and external device interfacing with controller. But
initialization sequence remains common across all platfoms.

Thus this patch merges gpmc_init() scattered in different arch-xx/mem.c
files into single omap-common/mem-common.c

However, actual platforms specific register config values are still sourced
from corresponding platform specific headers like;
 AM33xx: arch/arm/include/asm/arch-am33xx/mem.h
 OMAP3:  arch/arm/include/asm/arch-omap3/mem.h
 OMAP4:  arch/arm/include/asm/arch-omap4/mem.h
 OMAP4:  arch/arm/include/asm/arch-omap5/mem.h

Also, CONFIG_xx passed by board-profile decide config for which set of macros
need to be used for initialization
 CONFIG_NAND:    initialize GPMC for NAND device
 CONFIG_NOR:     initialize GPMC for NOR device
 CONFIG_ONENAND: initialize GPMC for ONENAND device

Signed-off-by: Pekon Gupta <pekon@ti.com>
[trini: define GPMC_SIZE_256M for omap3]
Signed-off-by: Tom Rini <trini@ti.com>

examples: select libgcc for non-default architecture

In case of multilib-enabled toolchains if default architecture differ from
the one examples are being built for linker will fail to link example object
files with libgcc of another (non-compatible) architecture.

Interesting enough for years in main Makefile we used CFLAGS/c_flags for this
but not for examples.

So fixing it now.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denx <wd@denx.de>
Acked-by: WOlfgang Denk <wd@denx.de>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

doc:git-mailrc: Add entry for dfu subsystem

Entry for dfu subsystem have been added to doc/git-mailrc file

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>

Add myself as maintainer for chromebook-x86

This is currently the only x86 board.

Signed-off-by: Simon Glass <sjg@chromium.org>

Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'

Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'