Lukas Auer [Wed, 21 Aug 2019 19:14:41 +0000 (21:14 +0200)]
Makefile: support building SPL FIT images without device trees
When building a U-Boot FIT image, the device trees specified by the
board are unconditionally built for inclusion in the FIT image. However,
not all device tree providers, such as CONFIG_OF_PRIOR_STAGE, require a
device tree to be built and bundled with the U-Boot binary. They rely on
other mechanisms to provide the device tree to U-Boot. Compilation on
boards with these device tree providers fails, because they do not
specify a device tree.
Change the makefile rules to conditionally build the device trees if
CONFIG_OF_SEPARATE, CONFIG_OF_EMBED, or CONFIG_OF_HOSTFILE is selected
as device tree provider.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Wed, 21 Aug 2019 19:14:40 +0000 (21:14 +0200)]
fdtdec: make CONFIG_OF_PRIOR_STAGE available in SPL
The current preprocessor logic prevents CONFIG_OF_PRIOR_STAGE from being
used in U-Boot SPL. Change the logic to also make it available in U-Boot
SPL.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tom Rini [Sat, 24 Aug 2019 12:33:27 +0000 (08:33 -0400)]
Merge tag 'u-boot-rockchip-
20190823' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver
Tom Rini [Sat, 24 Aug 2019 12:32:22 +0000 (08:32 -0400)]
Merge branch '2019-08-23-master-imports'
- Migrate CONFIG_MX_CYCLIC, CONFIG_FSL_USDHC and CONFIG_MXS_GPIO to
Kconfig
- Fix some SPL/TPL and ARM64 dependencies
Adam Ford [Wed, 14 Aug 2019 12:54:34 +0000 (07:54 -0500)]
Convert CONFIG_MX_CYCLIC to Kconfig
This converts the following to Kconfig:
CONFIG_MX_CYCLIC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: David Lechner <david@lechnology.com>
Adam Ford [Wed, 14 Aug 2019 12:23:43 +0000 (07:23 -0500)]
Convert CONFIG_FSL_USDHC to Kconfig
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
Adam Ford [Tue, 13 Aug 2019 19:32:30 +0000 (14:32 -0500)]
Kconfigs: Various: Fix some SPL, TPL and ARM64 dependencies
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
Lukasz Majewski [Tue, 13 Aug 2019 16:10:39 +0000 (18:10 +0200)]
kconfig: Convert CONFIG_MXS_GPIO to Kconfig
This converts the following to Kconfig:
CONFIG_MXS_GPIO
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/
571260789
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Fri, 23 Aug 2019 14:03:13 +0000 (10:03 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-clk
Max Kellermann [Tue, 4 Dec 2018 11:00:48 +0000 (12:00 +0100)]
evb_rk3399: revert CONFIG_SYS_MMC_ENV_DEV to 0
This was changed to 1 in commit
0717dde057e, but a few months later,
commit
5f9411af37b swapped the order of eMMC and SD card by assigning
indexed aliases to `&sdhci` and `&sdmmc`.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Add signature)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Urja Rannikko [Thu, 11 Apr 2019 20:27:51 +0000 (20:27 +0000)]
disk: efi: ignore 'IGNOREME' GPT header found on cros eMMCs
Some ChromeOS devices (atleast veyron speedy) have the first 8MiB of
the eMMC write protected and equipped with a dummy 'IGNOREME' GPT
header - instead of spewing error messages about it, just silently
try the backup GPT.
Note: this does not touch the gpt cmd writing/verifying functions,
those will still complain.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Urja Rannikko [Thu, 11 Apr 2019 20:27:50 +0000 (20:27 +0000)]
disk: efi: unify code for finding a valid gpt
There were 3 copies of the same sequence, make it into a function.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rohan Garg [Mon, 12 Aug 2019 15:04:36 +0000 (17:04 +0200)]
board: puma: Use rockchip_* helpers to setup cpuid and macaddr
We should use the shared helpers to setup the necessary parts
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rohan Garg [Mon, 12 Aug 2019 15:04:35 +0000 (17:04 +0200)]
rockchip: rk3399: Enable CONFIG_MISC_INIT_R for the Rock PI 4
This enables us to set a static MAC address
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rohan Garg [Mon, 12 Aug 2019 15:04:34 +0000 (17:04 +0200)]
rockchip: rk3399: derive ethaddr from cpuid
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.
The MAC address is only generated and set if there is no ethaddr
present in the saved environment.
This is based off of Klaus Goger's work in 8adc9d
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Tue, 20 Aug 2019 10:01:44 +0000 (18:01 +0800)]
rockchip: rk3288: remove fennec board support
Since there is no one using this board, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Tue, 20 Aug 2019 03:47:02 +0000 (11:47 +0800)]
rockchip: rk3399: defconfig: remove SPL raw image support
RK3399 SPL only support FIT image for ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Tue, 20 Aug 2019 03:47:01 +0000 (11:47 +0800)]
rockchip: rk3368: defconfig: remove SPL raw image support
RK3368 SPL only support FIT image for ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Tue, 20 Aug 2019 03:47:00 +0000 (11:47 +0800)]
rockchip: rk3328: defconfig: remove SPL raw image support
RK3328 SPL only support FIT image for ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 19 Aug 2019 07:01:24 +0000 (15:01 +0800)]
rockchip: Move config SYS_MALLOC_LEN to Kconfig
Use Kconfig for option SYS_MALLOC_LEN and default to 0x2000000.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Thu, 15 Aug 2019 03:13:28 +0000 (11:13 +0800)]
rockchip: dts: rk3328-rock64: fix usb power supply
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Thu, 15 Aug 2019 03:40:56 +0000 (11:40 +0800)]
rockchip: rk3328: migrate u-boot node to -u-boot.dtsi
Move all the nodes only shown in u-boot to -u-boot.dtsi to make
rk3328.dtsi clean.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Thu, 15 Aug 2019 03:28:31 +0000 (11:28 +0800)]
rockchip: dts: rk3328-rock64: enable usb3 xhci controller
Rock64 has a USB3.0 port, enable the controller so that we can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Thu, 15 Aug 2019 07:37:31 +0000 (15:37 +0800)]
rockchip: clk: rk3328: add clk_enable ops for HCLK_HOST0
Required to successfully probe the ehci generic driver
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 12 Aug 2019 12:02:29 +0000 (20:02 +0800)]
ram: rk3399: update cap and ddrconfig for each channel after init
We need to store all the ram related cap/map info back to register
for each channel after all the init has been done in case some of register
was reset during the process.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Thu, 22 Aug 2019 11:29:54 +0000 (07:29 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- i2c dm model support of lx2160a, ls1088a, lx2088a, ls1028a
- icid setup for ls1028a, ls1088a
- other small fixes
Laurentiu Tudor [Tue, 30 Jul 2019 14:29:59 +0000 (17:29 +0300)]
armv8: ls1028a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, edma, qdma, gpu, display and sec.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 30 Jul 2019 14:29:58 +0000 (17:29 +0300)]
armv8: ls1088a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 30 Jul 2019 14:29:57 +0000 (17:29 +0300)]
armv8: fsl-layerscape: make icid setup endianness aware
The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 30 Jul 2019 14:29:56 +0000 (17:29 +0300)]
armv8: fsl-layerscape: add base addresses for several devices
Add CCSR base addresses for ESDHC2, EDMA QDMA, DISPLAY and GPU devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 30 Jul 2019 14:29:55 +0000 (17:29 +0300)]
armv8: fsl-layerscape: add missing sec jr base address defines
Add defines for all the SEC job rings base addresses.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 2 Aug 2019 08:53:53 +0000 (16:53 +0800)]
armv8: kconfig: Fix some platforms incorrect I2C clock divider
By default, i2c input clock is platform clk / 2, but some of the
platform of i2c clock divider does not meet this kind of circumstance,
so alone to set default values for these platforms.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Thu, 1 Aug 2019 08:36:57 +0000 (16:36 +0800)]
armv8: ls1088aqds: support DSPI mode by hwconfig
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used
to control SPI and other IP signal routing.
USBOSC:
0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz.
SPI devices are unusable in this mode.
1= SPI_CLK used as SPI clock.
SPI devices are usable in this mode. USB block is clocked from
internal sources
SPR[3:2]:
SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]):
00= SDHC/eMMC 8-bit
01= SD Card Rev 2.0/3.0
10= SPI on-board memory
11= TDM Riser / SPI off-board connector.
The default value is 00 if an SDCard/eMMC card is selected as the boot
device.
SPR[1:0]:
SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]):
00= SDHC Sync loop
01= TDM Riser / SPI off-board connector.
10= SPI on-board memory.
11= SPI off-board connector.
By default, the SPI feature is not available, so we need to configure
the above register fields to select the route to the SPI feature.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pankaj Bansal [Tue, 23 Jul 2019 07:22:05 +0000 (07:22 +0000)]
armv8: ls1028aqds: define ARCH_MISC_INIT to handle mux
Define ARCH_MISC_INIT for LS1028AQDS platform to handle board
related mux.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Alison Wang [Mon, 22 Jul 2019 07:17:21 +0000 (07:17 +0000)]
armv8: ls1046afrwy: Define CONFIG_ENV_ADDR for QSPI Boot
Defines CONFIG_ENV_ADDR for QSPI Boot which specifies the start
address of the flash sector containing the environment. It fixes
the issue that bootcmd is always set as default at bootup.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pankaj Bansal [Wed, 17 Jul 2019 09:34:34 +0000 (09:34 +0000)]
boards: fsl: lx2160ardb: enable flexcan
Flexcan in LX2160ARDB is controlled by FPGA register boardcfg4
bit 5. enable this bit so that flexcan is enabled in LX2160ARDB.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 12:25:37 +0000 (20:25 +0800)]
configs: ls1088a: Enable DM support for pcf2127 rtc
Enable related configs on all ls1088aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 12:25:36 +0000 (20:25 +0800)]
armv8: dts: ls1088aqds : Add pcf2127 node
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 12:25:35 +0000 (20:25 +0800)]
armv8: ls1088aqds: Add support of I2C driver model.
Udate ls1088aqds board init code to support DM_I2C.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Tue, 23 Jul 2019 10:43:15 +0000 (18:43 +0800)]
armv8: dts: ls1088ardb: Add slave nodes under the i2c0 controller
This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Tue, 23 Jul 2019 10:43:14 +0000 (18:43 +0800)]
armv8: dts: ls1088a: add I2C node support
One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Tue, 23 Jul 2019 10:43:12 +0000 (18:43 +0800)]
gpio: do not include <asm/arch/gpio.h> on ARCH_LS1088A
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Tue, 23 Jul 2019 10:43:11 +0000 (18:43 +0800)]
boards: ls1088a: Add support of I2C driver model
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 11:24:03 +0000 (19:24 +0800)]
configs: ls2088a: Enable DM support for ds3231 rtc
Enable related configs on all ls2088aqds boards to support ds3231
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 11:24:02 +0000 (19:24 +0800)]
armv8: dts: ls2088aqds : Add ds3232 node
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds
boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 11:24:01 +0000 (19:24 +0800)]
boards: ls2088aqds: Add support of I2C driver model.
Update ls2088aqds board init code to support DM_I2C.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Fri, 26 Jul 2019 11:24:00 +0000 (19:24 +0800)]
rtc: ds3232/ds3231: Add support to generate 32KHz output for driver module
Add an implementation of the rtc_enable_32khz_output() that uses the
driver model i2c APIs.
Also put code related to rtc_enable_32khz_output
under CONFIG_RTC_ENABLE_32KHZ_OUTPUT.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Mon, 22 Jul 2019 08:36:46 +0000 (16:36 +0800)]
armv8: dts: ls2088ardb: Add slave nodes under the i2c0
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
chuanhua han [Mon, 22 Jul 2019 08:36:45 +0000 (16:36 +0800)]
armv8: dts: fsl-ls2088a: add i2c node support
One ls2088a, there are four I2C controllers. So add I2C nodes in dts
for ls2088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Mon, 22 Jul 2019 08:36:43 +0000 (16:36 +0800)]
gpio: do not include <asm/arch/gpio.h> on ARCH_LS2080A
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2080a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Mon, 22 Jul 2019 08:36:42 +0000 (16:36 +0800)]
boards: ls2088a: Add support of I2C driver model.
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls2088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 07:48:40 +0000 (15:48 +0800)]
armv8: dts: ls1028aqds: Add pcf2127 node under i2c1
Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 07:48:39 +0000 (15:48 +0800)]
armv8: dts: ls1028aqds: Add pca9547 node under the i2c0 controller
Add pca9547 node to support i2c multiplexer under the i2c0 controller
in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 07:48:38 +0000 (15:48 +0800)]
configs: ls1028a: Enable DM support for pcf2127 rtc
Enable related configs on all ls1028aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Tested-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 07:48:37 +0000 (15:48 +0800)]
armv8: ls1028aqds: Remove the definition of CONFIG_SYS_I2C_EARLY_INIT
Since i2c uses dm mode, i2c controller will be initialized when reading
and writing devices on i2c bus. So there is no need for the original
non-dm mode i2c early initialization function call, this patch removed
the definition of CONFIG_SYS_I2C_EARLY_INIT.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:16:52 +0000 (21:16 +0800)]
armv8: dts: ls1028ardb: Add slave nodes under the i2c0 controller
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:16:50 +0000 (21:16 +0800)]
gpio: do not include <asm/arch/gpio.h> on ARCH_LS1028A
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1028a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:16:49 +0000 (21:16 +0800)]
boards: ls1028a: Add support of I2C driver model
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1028a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:21 +0000 (21:00 +0800)]
configs: lx2160: enable DM support for pcf2127 rtc
Enable related configs on all lx2160ardb boards to support pcf2127
rtc DM feature.
Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from
Kconfig.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:05:13 +0000 (21:05 +0800)]
armv8: dts: lx2160aqds : Add pcf2127 node
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:26 +0000 (21:00 +0800)]
armv8: dts: lx2160ardb : Add the "u-boot, dm-pre-reloc" for i2c0
Lx2160ardb need to use i2c0 before relocation, so we also need to set
u-boot, dm-pre-reloc to initialize node before relocation.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:25 +0000 (21:00 +0800)]
armv8: dts: Add pcf2127 node for lx2160ardb
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:24 +0000 (21:00 +0800)]
armv8: dts: fsl-lx2160a: add i2c controller and gpio DT nodes
In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:23 +0000 (21:00 +0800)]
gpio: do not include <asm/arch/gpio.h> on ARCH_LX2160A
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2160a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:22 +0000 (21:00 +0800)]
drivers: i2c: mxc: Fix compiler error when using i2c dm mode
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Chuanhua Han [Wed, 10 Jul 2019 13:00:20 +0000 (21:00 +0800)]
boards: lx2160a: Add support of I2C driver model
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch solves
the problem that the i2c-related api of the lx2160a platform does not
support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Ashish Kumar [Tue, 9 Jul 2019 09:20:15 +0000 (14:50 +0530)]
configs: ls1043aqds: Move CONFIG_FSL_QSPI to defconfig
Move CONFIG_FSL_QSPI from header file to defconfigs,
consequently unset imply config(CONFIG_SPI_FLASH_BAR) which
is not valid for LS series.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Yuantian Tang [Tue, 2 Jul 2019 08:16:22 +0000 (16:16 +0800)]
armv8: ls1028a: select BOARD_LATE_INIT config
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Yuantian Tang [Wed, 19 Jun 2019 06:39:28 +0000 (14:39 +0800)]
common: qixis: make the qixis compatible with new soc
This driver needs modification to work with new soc,
like ls1028, since bitmap of RCFG is changed to
RESV[7:5] LIVE[4] WDEN[3] RESV[2:1] GO[0]
000 1 0 00 0
Also the RCW location is moved to only dutcfg0.
RESV[7:4] RCWSRC[3:0]
1111 configurable
Following commands are functional now
qixis_reset
qixis_reset sd
qixis_reset qspi
qixis_reset emmc
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Meenakshi Aggarwal [Thu, 23 May 2019 09:43:43 +0000 (15:13 +0530)]
drivers: net: mc: Report extra memory to Linux
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Peng Fan [Mon, 19 Aug 2019 07:54:04 +0000 (07:54 +0000)]
clk: imx: add i.MX8MM clk driver
Add i.MX8MM clk driver support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 19 Aug 2019 07:54:01 +0000 (07:54 +0000)]
clk: imx: add i.MX8M composite clk support
Import i.MX8M composite clk from Linux Kernel 5.3.0-rc2
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 19 Aug 2019 07:53:58 +0000 (07:53 +0000)]
clk: imx: add pll14xx driver
Add pll14xx driver for i.MX8MM usage, modifed
from Linux Kernel 5.3.0-rc1
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 19 Aug 2019 07:53:55 +0000 (07:53 +0000)]
clk: imx: expose CCF entry for all
Expose CCF entry, then we could avoid expand the SoC support list
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 21 Aug 2019 13:35:19 +0000 (13:35 +0000)]
sandbox: clk: add clk enable/disable test code
Since we added clk enable_count and prograte clk child enabling
operation to clk parent, so add a new function sandbox_clk_enable_count
to get enable_count for test usage.
And add test code to get the enable_count after we enable/disable
the device clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 21 Aug 2019 13:35:14 +0000 (13:35 +0000)]
clk: support clk tree dump
The previous code only dump the clk list. This patch is
to support clk tree dump, and also dump the enable_cnt.
The code used in patch is similar to dm_dump_all, but
the code here only filter out the UCLASS_CLK devices.
On i.MX8MM, Partial output:
u-boot=> clk dump
Rate Usecnt Name
------------------------------------------
24000000 0 |-- clock-osc-24m
24000000 0 | |-- dram_pll_ref_sel
750000000 0 | | `-- dram_pll
750000000 0 | | `-- dram_pll_bypass
750000000 0 | | `-- dram_pll_out
24000000 0 | |-- arm_pll_ref_sel
1200000000 0 | | `-- arm_pll
1200000000 0 | | `-- arm_pll_bypass
1200000000 0 | | `-- arm_pll_out
1200000000 0 | | `-- arm_a53_src
1200000000 0 | | `-- arm_a53_cg
1200000000 0 | | `-- arm_a53_div
24000000 4 | |-- sys_pll1_ref_sel
800000000 4 | | `-- sys_pll1
800000000 4 | | `-- sys_pll1_bypass
800000000 4 | | `-- sys_pll1_out
40000000 0 | | |-- sys_pll1_40m
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 21 Aug 2019 13:35:09 +0000 (13:35 +0000)]
clk: prograte clk enable/disable to parent
On i.MX8MM, thinking such as clk path
OSC->PLL->PLL GATE->CCM ROOT->CCGR GATE->Device
Only enabling CCGR GATE is not enough, we also need to enable PLL GATE
to make sure the clk path work. So when enabling CCGR GATE,
we could prograte to enabling PLL GATE to make life easier.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 21 Aug 2019 13:35:03 +0000 (13:35 +0000)]
clk: introduce enable_count
As what Linux Kernel 5.3.0 provides when enable/disable clk,
there is an enable_count in clk_core_disable/enable. Introduce
enable_count to track the clk enable/disable count when
clk_enable/disable for CCF. And Initialize enable_count to 0 when
register the clk.
And clk tree dump with enable_count will be supported, it will
be easy for us to check the clk status with enable_count
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Michal Simek [Mon, 19 Aug 2019 09:06:13 +0000 (11:06 +0200)]
test/py: Add cmd_memory dependency back to test_mmc_wr
Based on discussion with Stephen Warren there was recommendation to list
both memory and random command dependencies just in case that dependency is
not properly handled by Kconfig.
Fixes:
a09c1f7e1c1b ("test/py: Fix MMC/SD block write test dependency")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Heinrich Schuchardt [Thu, 15 Aug 2019 21:54:15 +0000 (23:54 +0200)]
easylogo: avoid buffer overrun
Building easylogo with `HOST_TOOLS_ALL=y make tools` results in a build
warning due to a possible buffer overrun:
tools/easylogo/easylogo.c:453:4: note: ‘sprintf’ output between 7 and
262 bytes into a destination of size 256
sprintf (str, "%s, 0x%02x", app, *dataptr++);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Truncate the output to fit into the destination buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Uwe Kleine-König [Wed, 14 Aug 2019 20:07:29 +0000 (22:07 +0200)]
jffs2: remove unused code files
I failed to find where these two files are used and a few test compile
runs with JFFS2 enabled succeeded also without these.
Fabien Parent [Mon, 12 Aug 2019 18:26:58 +0000 (20:26 +0200)]
mmc: mtk-sd: Add MT8183 SoC support
Add support for the MT8183 in the MediaTek MMC driver.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Heinrich Schuchardt [Sat, 10 Aug 2019 11:17:21 +0000 (13:17 +0200)]
mailmap: provide usage instruction
Looking at the contents of file .mailmap it seems that some editors assumed
that translation is done by entering multiple lines into the file and the
last one replaces the others. This is not how it works. The translation
occurs according to entries in single lines as described in the
git-check-mailmap man-page.
Add a description of the file format.
Add an entry for Alexander Graf as his old email address is not valid
anymore.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Andreas Dannenberg [Thu, 8 Aug 2019 17:54:49 +0000 (12:54 -0500)]
README: Clarify use of BSS during SPL board_init_f()
The earlier commit....
commit
a5a5d997b41a ("spl: Allow performing BSS init early before board_init_f()")
...introduced the ability to use BSS from SPL's board_init_f() as it may
be required in certain exceptional use cases so go ahead and update the
README to reflect this change. Note that as highlighted with the changes
the use of the associated CONFIG option is generally not recommended.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Wed, 21 Aug 2019 01:40:12 +0000 (21:40 -0400)]
Merge branch '2019-08-20-master-imports'
- Assorted bugfixes
Tom Rini [Wed, 21 Aug 2019 01:39:40 +0000 (21:39 -0400)]
Merge branch '2019-08-20-ti-imports'
- More DaVinci cleanups
- Other minor omap2plus cleanups
Michal Simek [Mon, 19 Aug 2019 09:06:13 +0000 (11:06 +0200)]
test/py: Add cmd_memory dependency back to test_mmc_wr
Based on discussion with Stephen Warren there was recommendation to list
both memory and random command dependencies just in case that dependency is
not properly handled by Kconfig.
Fixes:
a09c1f7e1c1b ("test/py: Fix MMC/SD block write test dependency")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Heinrich Schuchardt [Thu, 15 Aug 2019 21:54:15 +0000 (23:54 +0200)]
easylogo: avoid buffer overrun
Building easylogo with `HOST_TOOLS_ALL=y make tools` results in a build
warning due to a possible buffer overrun:
tools/easylogo/easylogo.c:453:4: note: ‘sprintf’ output between 7 and
262 bytes into a destination of size 256
sprintf (str, "%s, 0x%02x", app, *dataptr++);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Truncate the output to fit into the destination buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Uwe Kleine-König [Wed, 14 Aug 2019 20:07:29 +0000 (22:07 +0200)]
jffs2: remove unused code files
I failed to find where these two files are used and a few test compile
runs with JFFS2 enabled succeeded also without these.
Fabien Parent [Mon, 12 Aug 2019 18:26:58 +0000 (20:26 +0200)]
mmc: mtk-sd: Add MT8183 SoC support
Add support for the MT8183 in the MediaTek MMC driver.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Heinrich Schuchardt [Sat, 10 Aug 2019 11:17:21 +0000 (13:17 +0200)]
mailmap: provide usage instruction
Looking at the contents of file .mailmap it seems that some editors assumed
that translation is done by entering multiple lines into the file and the
last one replaces the others. This is not how it works. The translation
occurs according to entries in single lines as described in the
git-check-mailmap man-page.
Add a description of the file format.
Add an entry for Alexander Graf as his old email address is not valid
anymore.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Andreas Dannenberg [Thu, 8 Aug 2019 17:54:49 +0000 (12:54 -0500)]
README: Clarify use of BSS during SPL board_init_f()
The earlier commit....
commit
a5a5d997b41a ("spl: Allow performing BSS init early before board_init_f()")
...introduced the ability to use BSS from SPL's board_init_f() as it may
be required in certain exceptional use cases so go ahead and update the
README to reflect this change. Note that as highlighted with the changes
the use of the associated CONFIG option is generally not recommended.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Suniel Mahesh [Mon, 19 Aug 2019 06:27:39 +0000 (11:57 +0530)]
arm: omap2: am43xx: Enable CONFIG_BLK
With DM_MMC enabled, enable CONFIG_BLK to remove this
compile warning for am43xx based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Targets were compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Suniel Mahesh [Fri, 16 Aug 2019 08:46:36 +0000 (14:16 +0530)]
arm: dts: Makefile: clean *dtb_HS
TI HS platforms generate *dtb_HS binary blobs and there is no
rule for cleanup. Added entry for cleanup in clean-files target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Suman Anna [Fri, 16 Aug 2019 22:30:16 +0000 (17:30 -0500)]
ARM: DRA7: Fixup DPLL clock rate fixup logic for newer kernels
The commit
1b42ab3eda8a ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") updates the kernel device-tree blob to adjust
the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected
in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks
DT node.
The hierarchy of this clocks DT node has changed in newer Linux kernels
starting from v5.0, and this results in a failure in ft_fixup_clocks()
function to update the clock rates on these newer kernels. Fix this by
updating the lookup logic to look through both the newer and older
DT hierarchy paths for the cm_core_aon clocks node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Yegor Yefremov [Thu, 15 Aug 2019 09:08:04 +0000 (11:08 +0200)]
arm: baltos: switch to driver model for the watchdog timer
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Adam Ford [Wed, 14 Aug 2019 13:11:09 +0000 (08:11 -0500)]
davinci: omapl138-lcdk: Remove empty compiler directives
There is an #ifdef with nothing inside it any longer. This patch
removes this empty #ifdef
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Tue, 13 Aug 2019 19:38:11 +0000 (14:38 -0500)]
ARM: davinci: Remove duplicated references
The Kconfig file calls to ti/common/Kconfig twice which makes
several of the menu items repeat themselves. In an effort to
clean this up, this patch removes the second call which eliminates
the duplicate menu items.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Tue, 13 Aug 2019 13:28:28 +0000 (08:28 -0500)]
ARM: da850evm: Remove dead code
Now that SPL supports DM_SERIAL and the direct NOR boot supports
DM_SERIAL, the check to see if DM_SERIAL is defined can go away,
because all da850evm variants now support DM_SERIAL. This patch
simply removes some dead precompiler defines.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Tue, 13 Aug 2019 13:27:28 +0000 (08:27 -0500)]
ARM: da850evm: Remove dead SPI Code
With SPL now supporting DM_SPI, the need for compiler directives
and hard-coded addresses is obsolete. This patch removes some
dead legacy code defining the SPI base address
Signed-off-by: Adam Ford <aford173@gmail.com>
projects / oweals / u-boot.git / log