sh: convert to common timer code

Convert sh to use the commmon timer code. Remove reset_timer and
set_timer as they are unused on sh.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Introduce common timer functions

Many platforms duplicate pretty much the same timer code yet they all have
a 32-bit freerunning counter register. Create a common implementation that
minimally requires 2 or 3 defines to add timer support:

CONFIG_SYS_TIMER_RATE - Clock rate of the timer counter
CONFIG_SYS_TIMER_COUNTER - Address of 32-bit counter
CONFIG_SYS_TIMER_COUNTS_DOWN - Define if counter counts down

All functions are weak or ifdef'ed so they can still be overriden by any
platform.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

examples: enable gc-sections option

This fixes building time.c when unreferenced functions are added.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: remove platform CONFIG_SYS_HZ definition part 2/2

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: remove platform CONFIG_SYS_HZ definition part 1/2

Remove platform CONFIG_SYS_HZ definition for configs A-Z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: consolidate CONFIG_SYS_HZ definition

According to the README, CONFIG_SYS_HZ must be 1000 and most platforms
follow that. In preparation to remove CONFIG_SYS_HZ from all these
platforms, provide a common definition. The platforms which use a value
other than 1000 will get build warning now. These configs are:

include/configs/M5271EVB.h:#define CONFIG_SYS_HZ                        1000000
include/configs/balloon3.h:#define      CONFIG_SYS_HZ                   3250000         /* Timer @ 3250000 Hz */
include/configs/idmr.h:#define CONFIG_SYS_HZ                    (50000000 / 64)
include/configs/mini2440.h:#define CONFIG_SYS_HZ                        1562500
include/configs/mx1ads.h:#define CONFIG_SYS_HZ                  3686400
include/configs/omap3_zoom2.h:#define CONFIG_SYS_HZ                     ((V_SCLK) / (2 << CONFIG_SYS_PTV))
include/configs/omap730p2.h:#define CONFIG_SYS_HZ                       ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
include/configs/palmld.h:#define        CONFIG_SYS_HZ                   3250000         /* Timer @ 3250000 Hz */
include/configs/palmtc.h:#define        CONFIG_SYS_HZ                   3686400         /* Timer @ 3686400 Hz */
include/configs/rsk7203.h:#define CONFIG_SYS_HZ                 (CONFIG_SYS_CLK_FREQ / CMT_CLK_DIVIDER)
include/configs/rsk7264.h:#define CONFIG_SYS_HZ         (CONFIG_SYS_CLK_FREQ / CMT_CLK_DIVIDER)
include/configs/rsk7269.h:#define CONFIG_SYS_HZ         (CONFIG_SYS_CLK_FREQ / CMT_CLK_DIVIDER)
include/configs/scb9328.h:#define CONFIG_SYS_HZ                 3686400      /* incrementer freq: 3.6864 MHz */
include/configs/versatile.h:#define CONFIG_SYS_HZ                       (1000000 / 256)
include/configs/zipitz2.h:#define       CONFIG_SYS_HZ                   3250000         /* Timer @ 3250000 Hz */

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Merge branch 'master' of git://git.denx.de/u-boot-blackfin

Easy to resolve conflict on the GPIO change.

Conflicts:
arch/blackfin/cpu/Makefile

Signed-off-by: Tom Rini <trini@ti.com>

blackfin: Move machine specific gpio_port_t structure back to blackfin arch folder.

The gpio register mappings are different among blackfin processors.

Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

blackfin: fix a warning in arch/blackfin/cpu/cpu.c

This commit fixes:
    cpu.c:107: warning: ‘noreturn’ function does return

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

board/keymile/kmp204x/Makefile: Convert to SPDX tag

Signed-off-by: Tom Rini <trini@ti.com>

board: powerpc: convert more makefiles to Kbuild style

Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>

Makefile: convert makefiles to Kbuild style and delete grep switch

We have converted all makefiles needed to build $(LIBS).

Until this commit we used to grep switch so that U-Boot style
and Kbuild style makefiles coexist.
But we do not need any more.

Goint forward, use always Kbuild style Makefile when adding
a new Makefile

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

dts, api, test: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

post: convert makefiles to Kbuild style

This commit also deletes post/rules.mk,
which in not necessary any more.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

board: powerpc: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>

board: arm: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@ti.com>

blackfin: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>

m68k: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>

x86: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>

nios2: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Thomas Chou <thomas@wytron.com.tw>

nds32: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Macpaul Lin <macpaul@gmail.com>

mips: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

microblaze: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>

openrisc: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>

avr32: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>

sh: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

sparc: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>

sh: Do not include start.o in lib$(CPU).o

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

sparc: fix a link error

Before this commit, arch/sparc/lib/Makefile used
both COBJS and COBJS-y.
And it missed to add COBJS-y into OBJS.
This means bootm.o was never compiled even if
CONFIG_CMD_BOOTM=y

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>

ARM: s5pc, exynos: move Samsung ARM SoC specific code under arch/arm/

This patch moves S5PC, EXYNOS specific directory entries
from the toplevel Makefile to arch/arm/cpu/armv7/Makefile
using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>

ARM: omap: move OMAP specific code under arch/arm/

This patch moves OMAP specific directory entries
from the toplevel Makefile and spl/Makefile
to arch/arm/cpu/armv7/Makefile using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>

ARM: tegra: move Tegra specific code under arch/arm/

This patch moves Tegra specific directory entries
from the toplevel Makefile and spl/Makefile
to arch/arm/cpu/*/Makefile using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <TWarren@nvidia.com>

fs: move some file system to fs/Makefile

This commit moves some subdirectories of fs
from the toplevel Makefile to fs/Makefile
using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

drivers: move some drivers to drivers/Makefile

This commit moves some drivers subdirectory entry
from the toplevel Makefile to drivers/Makefile
using Kbuild descending feature.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Makefile: support descending down to subdirectories

This patch tweaks scripts/Makefile.build to allow
the build system to descend into subdirectories like Kbuild.

To use this feature, use "obj-y += foo/" syntax.

Example:
    obj-$(CONFIG_FOO) += foo/

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>

board: ti: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>

powerpc: convert makefiles to Kbuild style

Note:
arch/powerpc/cpu/mpc8260/Makefile is originally like follows:

    ---<snip>---
    START   = start.o kgdb.o
    COBJS   = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
    ---<snip>---
    COBJS-$(CONFIG_ETHER_ON_SCC) = ether_scc.o
    ---<snip>---
    $(LIB): $(OBJS)
            $(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)

The link rule `$(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)'
is weird.
kbdg.o is not included in $(OBJS) but linked into $(LIB)
and $(LIB) is not dependent on kgdb.o.
(Broken dependency tracking)

So,
    START   = start.o kgdb.o
shoud have been
    START   = start.o
    SOBJS   = kgdb.o

That is why this commit adds kgdb.o to obj-y, not to extra-y.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>

sandbox: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

disk: convert a makefile to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

lib: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

net: convert a makefile to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

common: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

fs: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

drivers: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

drivers: usb: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

drivers: mtd: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

drivers: net: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: imx-common: convert makefiles to Kbuild style

Multiple targets are included in arch/arm/imx-common/Makefile
In order to refactor it,
we need to tweak Makefile and spl/Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

ARM: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

arm720t: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

arm920t: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

arm926ejs: convert makefiles to Kbuild style

Note1:
In arch/arm/cpu/arm926ejs/spear/Makefile
START := start.o
was changed
extra-$(CONFIG_SPL_BUILD) := start.o
because spear/start.o is only used for SPL.

Note2:
START := start.o
was missing from arch/arm/cpu/arm926ejs/mxs/Makefile.
This commit simply adds
extra-$(CONFIG_SPL_BUILD) := start.o

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

armv7: convert makefiles to Kbuild style

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Makefile: prepare for using Kbuild-style Makefile

Every makefile in sub directories has common lines
at the top and the bottom.
This commit pushes the common parts into script/Makefile.build.

Going forward sub-makefiles only need to describe this part:

    COBJS := ...
    COBJS += ...
    SOBJS := ...

But using obj-y is preferable to prepare for switching to Kbuild.

The conventional (non-Kbuild) Makefile style is still supported.
This is achieved by greping the Makefile before entering into it.
U-Boot conventional sub makefiles always include some other makefiles.
So the build system searches a line beginning with "include" keyword
in the makefile in order to distinguish which style it is.
If the Makefile include a "include" line, we assume it is a conventional
U-Boot style. Otherwise, it is treated as a Kbuild-style makefile.

With this tweak, we can switch sub-makefiles
from U-Boot style to Kbuild style little by little.

obj-y := foo/
syntax (descending into the sub directory) is not supportd yet.
It will be implemented in the upcomming commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>

nand_util.c: Correct licensing

Prior to SPDX licensing this file was GPL-2.0 with Freescale granting
rights for "or later" for their contributed code.  We incorrectly moved
this file to GPL-2.0+, so correct it to GPL-2.0.  In addition we cannot
easily denote in the file where or what code is "or later", so just set
that aside for now and the file as a whole is GPL-2.0 regardless.

Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>

powerpc/esdhc: Add 3.3v voltage support in esdhc capacity register

T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

esdhc: memset mmc struct before putting into use

struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.

Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.

Test on P5040 and T4240,
Error Log:

=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

Powerpc/esdhc: Add simple description of esdhc register

Add some descriptions for esdhc register for easily using.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

powerpc/esdhc: Map register for eSDHC Host Controller V3.0

eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

DWMMC: SMDK5420: Disable SMU for eMMC

SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

mmc: sdhci: Avoid commands errors by simple timeout adaptation.

Old command timeout value was too small and it caused I/O errors which
led to uncompleted read/write/erase operations and filesystem errors.
Timeout adaptation fixes this issue.

Changes in sdhci_send_command() function:
- change timeout variable to static
- increase default command timeout to 100 ms
- add definition of max command timeout value,
  which can be redefined in each board config file
- wait for card ready state for max defined time
  if it doesn't exceed defined maximum or return COMM_ERR

Once successfully increased timeout value will be used in next function
call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS
on MMC storage.

Changes v2:
- move global variable cmd_timeout into function sdhci_send_command()
- change condition "==" to ">=" when comparing time with timeout
- print information about timeout increasing and card busy timeout

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>

mmc: dw_mmc: change the callback function name.

To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

mmc: Fix erase_grp_size for partitioned card

EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or
 power off. Set it if device has enhanced partitions.

Signed-off-by: Oliver Metz <oliver@freetz.org>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

Merge branch 'master' of git://git.denx.de/u-boot-video

video, formike: change tag/val write

write first the "tag" 8 bit value and then the "val" 8-bit
to the display.

Tested on the rut board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>

video, cfb_console: make background and foreground color configurable

make CONSOLE_BG_COL/CONSOLE_FG_COL configurable through board config file.
Clear video screen in video_init().

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>

video: ipu_disp: Fix clock polarity logic

Currently the HDMI splash screen image quality on mx6solo does not show a
very stable image.

By comparing the IPU driver from U-boot with the one from FSL 4.1.0 BSP,
we can see that there is an inverted logic for setting the DI_GEN_POL_CLK bit.

>From FSL BSP [1] we have:

if (!sig.clk_pol)
di_gen |= DI_GEN_POLARITY_DISP_CLK;

Applying the same logic into U-boot fixes the HDMI image stability.

[1] git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/drivers/mxc/ipu3/ipu_disp.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>

mpc85xx: introduce the kmp204x reference design support

This patch introduces the support for Keymile's kmp204x reference
design. This design is based on Freescale's P2040/P2041 SoC.

The peripherals used by this design are:
- DDR3 RAM with SPD support
- SPI NOR Flash as boot medium
- NAND Flash
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
  FPGA
- 2 HW I2C busses
- last but not least, the mandatory serial port

The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb
support and was changed according to our design (that means essentially
removing what is not present on the designs and a few adaptations).

There is currently only one prototype board that is based on this design
and this patch also introduces it. The board is called kmlion1.

Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
kmp204x: update the ENV #define

The comments had to be refined as well as the total size

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix ddr.c]
Acked-by: York Sun <yorksun@freescale.com>

fsl/mpc85xx: define common serdes_clock_to_string function

This allows to share some common code for the boards that use a corenet
base SoC.

Two different versions of the function are available in
fsl_corenet_serdes.c and fsl_corenet2_serdes.c files.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix t1040qds.c]
Acked-by: York Sun <yorksun@freescale.com>

mtd/fsl_elbc: take NAND_ECC_SOFT_BCH config option into account

NAND_ECC_SOFT was the only option available while the SOFT_BCH option
may also be used.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Scott Wood <scottwood@freescale.com>

net/fman: add a fm_enable_port function

This can be useful if one wants to disable an interface in u-boot
because u-boot should not manage it but then later reenable it for FDT
fixing or if the kernel uses this interface.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix conflict in fm_eth.h]
Acked-by: York Sun <yorksun@freescale.com>

mpc8xxx: set x2 DDR3 refresh rate if SPD config requires it

If the DDR3 module supports industrial temperature range and requires
the x2 refresh rate for that temp range, the refresh period must be
3.9us instead of 7.8 us.

This was successfuly tested on kmp204x board with some MT41K128M16 DDR3
RAM chips (no module used, chips directly soldered on board with an SPD
EEPROM).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix minor conflicts in fsl_ddr_dimm_params.h,
   lc_common_dimm_params.c, common_timing_params.h]
Acked-by: York Sun <yorksun@freescale.com>

mpc8xxx: call i2c_set_bus_num in __get_spd

This is necessary with the new I2C subystem that was introduced lately.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

KM: add CONFIG_KM_COMMON_ETH_INIT for km common eth init

This must be defined by a board support file that want to use the
keymile common.c board_eth_init function that requires ethernet_present
to be defined.

Currently all the km architectures use it but the kmp204x architecture
later supported in this series does use another board_eth_init function
and thus does not define it.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

KM: define CONFIG_SYS_I2C_INIT_BOARD only for concerned board

This must be defined for all the keymile boards that use the common
i2c_abort function that is used to "reset" the I2C bus. These are
currently km82xx and km_arm boards.

The  km83xx boards use other functions and thus do not need this.

This patch removes the CONFIG_SYS_I2C_INIT_BOARD from keymile-common.h
and defines it for km_arm.h and km82xx.h.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

KM: fix typo in default environment

The ip kernel parameter had a typo in it (we've been lucky that it has
worked until now).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

km-powerpc: move SYS_MALLOC_LEN out of keymile-common.h

It must be set to a different value for the later add kmp204x
architecture, because we are restricted to 1MB SRAM.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

powerpc: cast bi_memsize to ulong for %ld usage

When exporting the new memsize without reserved PRAM area, the -Wformat
option produces a warning since %ld is used for snprintf and bi_memsize
is phys_size_t.

This patch removes this warning for all PRAM PowerPC boards.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

powerpc/usb:Differentiate USB controller base address

Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>

powerpc/usb:Define CONFIG_USB_MAX_CONTROLLER_COUNT for all 85xx socs

CONFIG_USB_MAX_CONTROLLER_COUNT macro recently defined for
initializing all USB controllers on a given platform. This
macro is defined for all 85xx socs

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>

powerpc/c29xpcie: add DDR ECC on off config setting

c29xpcie REV_A board DDR ECC chip has bad impedance in hardware,
force that kind of board to be DDR ECC off when booting.
Other version board config ECC on/off by hwconfig=fsl_ddr:ecc=on
in uboot enviroment.

Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

usb: rename board_usb_init_type to usb_init_type

commit bba679144d25b91bcd7befff5a96728a30875f54
"usb: rename board_usb_init_type to usb_init_type" missed xhci-omap.c
So, fix that patch here, and fix a checkpatch warning.
WARNING: Avoid unnecessary line continuations

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

arm: rmobile: armadillo-800eva: Change clock definition of SCIF and TMU

This changes clock definition of SCIF from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_SCIF_CLK_FREQ, and clock definition of TMU from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_TMU_CLK_FREQ,

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>

arm: rmobile: kzm9g: Change clock definition of SCIF from CONFIG_SYS_CLK_FREQ to CONFIG_SH_SCIF_CLK_FREQ

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>

Merge branch 'master' of git://git.denx.de/u-boot-sh

Merge branch 'master' of git://git.denx.de/u-boot-usb

usb: udc: add udc.h include file

Move common definitions to udc.h
This allows musb_udc.h to be removed as well.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: gadget: mv_udc: split mv_udc.h file

Move defines only needed by mv_udc.c to a file
in the same directory.

This allows usbtty to compile for mv_udc,
but it still doesn't link.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: gadget: mv_udc: optimize ep_enable

Only get head if not ep0.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: gadget: mv_udc: optimize bounce

Only perform one copy, either in the bounce
routine for IN transfers, or the debounce
rtn for OUT transfer.

On out transfers, only copy the number
of bytes received from the bounce buffer

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: gadget: mv_udc: fix full speed connections

Set maximum packet length in queue header to wMaxPacketSize
of endpoint.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: ehci-mx6: add support for otg port

Previously, only host1 was supported using an index of 0.
Now, otg has index 0, host1 is 1, host2 is 2, host3 is 3.
Since OTG requires usbmode to be set after reset, I added
CONFIG_EHCI_HCD_INIT_AFTER_RESET to nitrogen6x.h and
mx6qsabreauto.h.

I also added a weak function board_ehci_power to handle
turning power on/off for otg.

Type is type of device connected (USB stick vs Host.)
Init is type of device desired.
Only power up port if type == init == USB_INIT_HOST.
Only return error if type != init.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: gadget: mv_udc: don't check CONFIG_USB_MAX_CONTROLLER_COUNT

i.mx6 has 1 otg controller, and 3 host ports. So,
CONFIG_USB_MAX_CONTROLLER_COUNT can be greater than 1
even though only 1 device mode controller is supported.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: ehci-hcd: add enum usb_init_type parameter to ehci_hcd_init.

This paramter will later be used to initialize OTG ports in
host or device mode.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: add enum usb_init_type parameter to usb_lowlevel_init

This parameter will later be used to verify OTG ports.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

usb: rename board_usb_init_type to usb_init_type

This will be used by usb_lowlevel_init so it will
no longer be used by only board specific functions.

Move definition of enum usb_init_type higher in file
so that it will be available for usb_low_level_init.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

ARM: omap5-evm: Move MAC creation to misc_init

Move the MAC creation from the USB init to an function
that is called on every boot.  This will then populate the
usbethaddr mac that kernel driver can pick up from the
device tree blob.

Signed-off-by: Dan Murphy <dmurphy@ti.com>

usb: am437x: Add support for am437x xhci USB host

Add the support for the am437x xhci usb host.

The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>

usb: dra7xx: Add support for dra7xx xhci USB host

Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>