oweals/openwrt.git
7 years agozlib: Update to 1.2.11
Daniel Engberg [Sun, 15 Jan 2017 20:46:27 +0000 (21:46 +0100)]
zlib: Update to 1.2.11

Update to 1.2.11 as suggested by upstream
Also add SF as primary source and main site as fallback

Note: SF doesn't carry the 1.2.11 update yet.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
7 years agolede-keyring: bundle latest usign certificates
Jo-Philipp Wich [Fri, 20 Jan 2017 09:09:30 +0000 (10:09 +0100)]
lede-keyring: bundle latest usign certificates

Includes the public usign certificates used by the 17.01.* release builds.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agosdk: fix Git URL detection
Jo-Philipp Wich [Fri, 20 Jan 2017 08:51:38 +0000 (09:51 +0100)]
sdk: fix Git URL detection

Instead of relying on complex sed patterns that trip up make syntax rules, use
GNU Makes builtin filter function to match desired URLs.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agosdk: avoid using private repository clone urls as base repo entry
Jo-Philipp Wich [Thu, 19 Jan 2017 19:41:46 +0000 (20:41 +0100)]
sdk: avoid using private repository clone urls as base repo entry

Only consider the repository origin url as valid base feed entry if it is a
git://, http:// or https:// location.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agolantiq: fix an ethernet stability issue triggered by receving packets during boot
Felix Fietkau [Thu, 19 Jan 2017 13:25:09 +0000 (14:25 +0100)]
lantiq: fix an ethernet stability issue triggered by receving packets during boot

Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.

This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agolantiq: fix spurious irq storm
Felix Fietkau [Thu, 19 Jan 2017 11:31:34 +0000 (12:31 +0100)]
lantiq: fix spurious irq storm

Since the MIPS IRQ stack patches, lantiq devices were emitting a storm
of messages like this:

[  567.872172] Spurious IRQ: CAUSE=0x1100c300

Fix this by reworking the IRQ dispatch code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agogit-kernel: $(SUBDIR) should always be $(LINUX_VERSION)
Mirko Vogt [Wed, 18 Jan 2017 13:36:45 +0000 (14:36 +0100)]
git-kernel: $(SUBDIR) should always be $(LINUX_VERSION)

Before SUBDIR was set to $(PATCHVER) which may
or may not include the minor version number of
the linux kernel version. Usually it doesn't.

So the git-clone'd linux kernel was packed without
the minor version number taken into account, which
broke further processing, as it expected the
extracted dir being named linux-$(LINUX_VERSION)
(=with minor version) rather than linux-$(PATCHVER)
(=without minor version).

Changing SUBDIR to $(LINUX_VERSION) creates
consistent behaviour here.

Signed-off-by: Mirko Vogt <mirko-openwrt@nanl.de>
7 years agosdk: do not strip static libraries
Jo-Philipp Wich [Wed, 18 Jan 2017 02:15:31 +0000 (03:15 +0100)]
sdk: do not strip static libraries

Do not strip static libraries shipped with the SDK in order to preserve the
archive index. If we strip the index of the shipped libraries, host programs
will fail to link these libraries with errors like:

    libssl.a: error adding symbols: Archive has no index; run ranlib to add one

The error was found while investigating a Python host build failure within
the SDK environment.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agonetifd: update to git HEAD version
Hans Dedecker [Tue, 17 Jan 2017 13:00:02 +0000 (14:00 +0100)]
netifd: update to git HEAD version

a057f6e device: fix DEV_OPT_SENDREDIRECTS definition

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agocurl: fix HTTPS network timeouts with OpenSSL
Stijn Segers [Tue, 10 Jan 2017 18:57:47 +0000 (19:57 +0100)]
curl: fix HTTPS network timeouts with OpenSSL

Backport an upstream change to fix HTTPS timeouts with OpenSSL.
Upstream curl bug #1174.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
[Jo-Philipp Wich: reword commit message, rename patch to 001-*]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agoLEDE v17.01: set branch defaults
Jo-Philipp Wich [Mon, 16 Jan 2017 17:56:07 +0000 (18:56 +0100)]
LEDE v17.01: set branch defaults

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agobase-files: add ARCH_PACKAGES to openwrt_release and os-release
Matthias Schiffer [Mon, 16 Jan 2017 12:25:14 +0000 (13:25 +0100)]
base-files: add ARCH_PACKAGES to openwrt_release and os-release

Knowing the package architecture at runtime can be useful, e.g. to
configure opkg repository URLs. The value of ARCH_PACKAGES ("%A" in
VERSION_SED) as added to openwrt_release (as DISTRIB_ARCH) and os-release
(as LEDE_ARCH).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
7 years agoubox: turn logd into a separate package
Andrej Vlasic [Sun, 15 Jan 2017 18:30:53 +0000 (19:30 +0100)]
ubox: turn logd into a separate package

Currently system log is always included as a part of ubox. Add logd as a
seperate package and add it to default packages list.

Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
7 years agombedtls: add static files in staging_dir
Domagoj Pintaric [Sun, 1 Jan 2017 18:10:38 +0000 (19:10 +0100)]
mbedtls: add static files in staging_dir

Signed-off-by: Domagoj Pintaric <domagoj.pintaric@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
7 years agokernel: make ledtrig-netdev use a work queue for updates
Felix Fietkau [Sat, 14 Jan 2017 21:29:05 +0000 (22:29 +0100)]
kernel: make ledtrig-netdev use a work queue for updates

This fixes hangs in igb that happen if the update call interrupts an
already existing dev_get_stats call. In that case the calling CPU
deadlocks because it's trying to acquire the same spinlock recursively.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoinclude/feeds.mk: base list of enabled feeds on available instead of installed feeds
Matthias Schiffer [Mon, 16 Jan 2017 08:11:56 +0000 (09:11 +0100)]
include/feeds.mk: base list of enabled feeds on available instead of installed feeds

This fixes handling of CONFIG_FEED_* options for uninstalled feeds.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
7 years agoopkg: use default PKG_BUILD_DIR
Matthias Schiffer [Mon, 16 Jan 2017 08:02:42 +0000 (09:02 +0100)]
opkg: use default PKG_BUILD_DIR

opkg doesn't have BUILD_VARIANTs anymore, so the previously defined
PKG_BUILD_DIR would lead to a weird 'opkg-' path component.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
7 years agomac80211: brcmfmac: add early (& hacky) patch for storing country codes
Rafał Miłecki [Sun, 15 Jan 2017 23:32:27 +0000 (00:32 +0100)]
mac80211: brcmfmac: add early (& hacky) patch for storing country codes

This allows some basic region switching on Netgear R8000. More devices &
codes may be added. Ideally it should be converted into DT info & patch.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agomac80211: use wiphy_read_of_freq_limits in brcmfmac
Rafał Miłecki [Sun, 15 Jan 2017 22:04:18 +0000 (23:04 +0100)]
mac80211: use wiphy_read_of_freq_limits in brcmfmac

This makes use of cfg80211 feature backported & described in
188626f17c09 ("mac80211: backport cfg80211 support for
ieee80211-freq-limit DT property").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agobcm53xx: add pending BCM5301X patches: Netgear R8000 WiFi & Luxul DTS
Rafał Miłecki [Sun, 15 Jan 2017 21:52:24 +0000 (22:52 +0100)]
bcm53xx: add pending BCM5301X patches: Netgear R8000 WiFi & Luxul DTS

This specifies wireless limitations for Netgear R8000 making sure people
won't use channels incorrectly (limited performance). There are also 2
new DTS files not used by us yet.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agokernel: fix bcma serial console regression
Rafał Miłecki [Sun, 15 Jan 2017 21:57:50 +0000 (22:57 +0100)]
kernel: fix bcma serial console regression

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agoipq806x: refactor ipq8065 device tree
Pavel Kubelun [Sat, 14 Jan 2017 14:01:09 +0000 (17:01 +0300)]
ipq806x: refactor ipq8065 device tree

At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.

This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.

It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
7 years agoipq806x: enable hw pseudo random number generator
Pavel Kubelun [Sat, 14 Jan 2017 11:56:56 +0000 (14:56 +0300)]
ipq806x: enable hw pseudo random number generator

Enables support for pseudo random number generator in device tree.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
7 years agoipq806x: update eMMC and SDCC3 nodes in device tree
Pavel Kubelun [Wed, 28 Dec 2016 13:21:43 +0000 (16:21 +0300)]
ipq806x: update eMMC and SDCC3 nodes in device tree

Enable bam dma support for eMMC and SDCC3 in device tree and update nodes
to reflect Qualcomm SDK.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
7 years agoipq806x: disable usb3 phy suspend and add usb tcsr control
Pavel Kubelun [Fri, 23 Dec 2016 22:51:07 +0000 (01:51 +0300)]
ipq806x: disable usb3 phy suspend and add usb tcsr control

According to Qualcomm SDK usb3 phy suspend should be disabled for
ipq806x.
This may solve issue on some ipq806x devices that breaks usb3
storage peripherals during system boot.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
7 years agoramips: add back the i2c-mt7621 module
John Crispin [Sun, 15 Jan 2017 19:45:14 +0000 (20:45 +0100)]
ramips: add back the i2c-mt7621 module

mt7628/88 are still using this module.

Signed-off-by: John Crispin <john@phrozen.org>
7 years agomt76: select 802.11w support
Stijn Tintel [Sun, 15 Jan 2017 18:17:30 +0000 (19:17 +0100)]
mt76: select 802.11w support

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
7 years agoramips: Added Onion Omega2 and Omega2+
Lazar Demin [Mon, 9 Jan 2017 19:59:56 +0000 (19:59 +0000)]
ramips: Added Onion Omega2 and Omega2+

This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
7 years agokernel: can: Add missing regmap dependency for kernel 4.4
Florian Fainelli [Sun, 15 Jan 2017 05:34:02 +0000 (21:34 -0800)]
kernel: can: Add missing regmap dependency for kernel 4.4

Fixes build failure for kmod-can-c-can-platform which depends on
kmod-regmap for kernel 4.1 and 4.4.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
7 years agoar71xx: Detect USB port on Mikrotik RB750UP
João Chaínho [Fri, 13 Jan 2017 16:23:09 +0000 (16:23 +0000)]
ar71xx: Detect USB port on Mikrotik RB750UP

The USB port on Mikrotik RB750UP isn’t detected. This patch provides a fix. Tested and working.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
7 years agoramips: Add I2C driver to the default kernel config
Rosen Penev [Fri, 13 Jan 2017 15:14:38 +0000 (07:14 -0800)]
ramips: Add I2C driver to the default kernel config

I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
7 years agoimx6: kernel: Backport serial port fixes
Petr Štetiar [Fri, 13 Jan 2017 10:42:08 +0000 (11:42 +0100)]
imx6: kernel: Backport serial port fixes

Signed-off-by: Petr Štetiar <ynezz@true.cz>
7 years agokernel: backport MIPS changes introducing a separate IRQ stack
Felix Fietkau [Wed, 11 Jan 2017 09:57:49 +0000 (10:57 +0100)]
kernel: backport MIPS changes introducing a separate IRQ stack

Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agogitignore: add /overlay
Matthias Schiffer [Sun, 15 Jan 2017 17:16:29 +0000 (18:16 +0100)]
gitignore: add /overlay

Similar to /files, /overlay is only useful for modifications not tracked in
the LEDE repository itself.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
7 years agoath10k-firmware: Update QCA988X firmware to latest version
Timo Sigurdsson [Wed, 11 Jan 2017 21:49:29 +0000 (22:49 +0100)]
ath10k-firmware: Update QCA988X firmware to latest version

This patch updates the QCA988X firmware to the latest revision
  firmware-5.bin_10.2.4-1.0-00016
found in the official ath10k-firmware repository.

Tested on TP-Link Archer C7 v2.

Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
7 years agohostapd: fix passing jobserver to hostapd/supplicant build processes
Felix Fietkau [Sun, 15 Jan 2017 13:56:34 +0000 (14:56 +0100)]
hostapd: fix passing jobserver to hostapd/supplicant build processes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agohostapd: backport a few upstream fixes
Felix Fietkau [Sun, 15 Jan 2017 13:19:43 +0000 (14:19 +0100)]
hostapd: backport a few upstream fixes

Fixes reassoc issues with WDS mode
Fixes reassoc issues in AP mode
Fixes IBSS reauthentication issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomt76: update to the latest version, adds support for 802.11w
Felix Fietkau [Sat, 14 Jan 2017 22:09:34 +0000 (23:09 +0100)]
mt76: update to the latest version, adds support for 802.11w

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoncurses: revert $(STAGING_DIR_HOSTPKG) to $(STAGING_DIR)/host where appropriate
Matthias Schiffer [Sat, 14 Jan 2017 17:11:26 +0000 (18:11 +0100)]
ncurses: revert $(STAGING_DIR_HOSTPKG) to $(STAGING_DIR)/host where appropriate

Host files installed in Build/InstallDev are target-specific and will stay
in $(STAGING_DIR)/host after the STAGING_DIR_HOSTPKG unification.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
7 years agoinclude/autotools.mk: use STAGING_DIR_HOSTPKG where appropriate
Matthias Schiffer [Sat, 14 Jan 2017 17:09:33 +0000 (18:09 +0100)]
include/autotools.mk: use STAGING_DIR_HOSTPKG where appropriate

Make sure binaries install to STAGING_DIR_HOSTPKG are still found when
this variable is eventually modified.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
7 years agomac80211: backport a fix for a tx related race condition
Felix Fietkau [Sat, 14 Jan 2017 17:02:54 +0000 (18:02 +0100)]
mac80211: backport a fix for a tx related race condition

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomac80211: refresh patches
Felix Fietkau [Fri, 13 Jan 2017 09:42:35 +0000 (10:42 +0100)]
mac80211: refresh patches

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomac80211: backport some upstream fixes
Koen Vandeputte [Fri, 13 Jan 2017 09:34:52 +0000 (10:34 +0100)]
mac80211: backport some upstream fixes

Backports the following upstream fixes:

mac80211: initialize fast-xmit 'info' later
mac80211: fix legacy and invalid rx-rate report
mac80211: fix tid_agg_rx NULL dereference

Compiled and tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
7 years agokernel: update 4.4 kernel to 4.4.42
Hauke Mehrtens [Fri, 13 Jan 2017 21:35:45 +0000 (22:35 +0100)]
kernel: update 4.4 kernel to 4.4.42

Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agoimagebuilder: remove existing debug kernel image
Felix Fietkau [Fri, 13 Jan 2017 18:22:09 +0000 (19:22 +0100)]
imagebuilder: remove existing debug kernel image

Reduces tarball size and improves build time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoimagebuilder: remove existing root filesystem images
Felix Fietkau [Fri, 13 Jan 2017 18:21:31 +0000 (19:21 +0100)]
imagebuilder: remove existing root filesystem images

Reduces tarball size and improves build time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoxburst: remove hack to determine entry point
Felix Fietkau [Fri, 13 Jan 2017 18:20:57 +0000 (19:20 +0100)]
xburst: remove hack to determine entry point

xburst has CONFIG_BOOT_RAW set, so jumping to the load address is valid

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomalta: remove hack to determine entry point
Felix Fietkau [Fri, 13 Jan 2017 18:19:34 +0000 (19:19 +0100)]
malta: remove hack to determine entry point

Malta has CONFIG_BOOT_RAW set, so jumping to the load address is valid

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agosdk: exclude locale files to save some space
Felix Fietkau [Fri, 13 Jan 2017 17:00:18 +0000 (18:00 +0100)]
sdk: exclude locale files to save some space

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agofirewall: fix forwarding local subnet traffic
Jo-Philipp Wich [Fri, 13 Jan 2017 17:31:08 +0000 (18:31 +0100)]
firewall: fix forwarding local subnet traffic

Packets which are merely forwarded by the router and which are neither
involved in any DNAT/SNAT nor originate locally, are considered INVALID
from a conntrack point of view, causing them to get dropped in the
zone_*_dest_ACCEPT chains, since those only allow stream with state NEW
or UNTRACKED.

Remove the ctstate restriction on dest accept chains to properly pass-
through unrelated 3rd party traffic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agomvebu: simplify etc/board.d/02_network
Paul Wassi [Fri, 28 Oct 2016 18:22:22 +0000 (20:22 +0200)]
mvebu: simplify etc/board.d/02_network

Unify switch configuration on Linksys WRTxx00AC series.
LAN = eth0, WAN = eth1

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[Álvaro]: also change WAN LEDs
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
7 years agomvsw61xx: add support for MV88E6352
Imre Kaloz [Thu, 12 Jan 2017 21:50:06 +0000 (22:50 +0100)]
mvsw61xx: add support for MV88E6352

MV88E6352 is used on Linksys WRT3200ACM

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
7 years agomvebu: several fixes for Linksys WRT3200ACM
Álvaro Fernández Rojas [Wed, 11 Jan 2017 17:43:38 +0000 (18:43 +0100)]
mvebu: several fixes for Linksys WRT3200ACM

- Fix WLAN LEDs definition.
- Fix USB pinctrl definition.
- Remove SDHCI definition.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
7 years agomxs: gzip ext4 images
Felix Fietkau [Fri, 13 Jan 2017 14:23:36 +0000 (15:23 +0100)]
mxs: gzip ext4 images

Significantly reduces disk usage

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoarc770: gzip rootfs image to save some space
Felix Fietkau [Fri, 13 Jan 2017 15:22:13 +0000 (16:22 +0100)]
arc770: gzip rootfs image to save some space

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoarchs38: gzip rootfs image to save some space
Felix Fietkau [Fri, 13 Jan 2017 15:20:56 +0000 (16:20 +0100)]
archs38: gzip rootfs image to save some space

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoimage.mk: add generic function for gzipping images if enabled
Felix Fietkau [Fri, 13 Jan 2017 15:19:00 +0000 (16:19 +0100)]
image.mk: add generic function for gzipping images if enabled

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomvebu: remove the clearfog-bundle
Felix Fietkau [Fri, 13 Jan 2017 15:02:52 +0000 (16:02 +0100)]
mvebu: remove the clearfog-bundle

It is obsoleted by proper SD card image support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoimage: when using the new image build code, gzip ext4 images by default
Felix Fietkau [Fri, 13 Jan 2017 14:58:37 +0000 (15:58 +0100)]
image: when using the new image build code, gzip ext4 images by default

This reduces the amount of hacks in the makefile code.

Remove the apm821xx code to do the same - it was broken and left both
compressed and uncompressed images in $(BIN_DIR)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agodnsmasq: use ubus signalling in ntp hotplug script
Kevin Darbyshire-Bryant [Thu, 12 Jan 2017 19:28:53 +0000 (19:28 +0000)]
dnsmasq: use ubus signalling in ntp hotplug script

Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
7 years agox86: disable crashlog
Felix Fietkau [Fri, 13 Jan 2017 13:48:25 +0000 (14:48 +0100)]
x86: disable crashlog

It could cause crashes with some forms of virtualization, and it is
unlikely to work properly with most systems.
It's safer to just disable it.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agox86: disable a workaround for a buggy glibc version
Felix Fietkau [Fri, 13 Jan 2017 13:47:40 +0000 (14:47 +0100)]
x86: disable a workaround for a buggy glibc version

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoocteon: disable ext4 images
Felix Fietkau [Fri, 13 Jan 2017 13:03:01 +0000 (14:03 +0100)]
octeon: disable ext4 images

They're pretty large and squashfs images tend to be more useful anyway

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agonetifd: update to the latest version
Felix Fietkau [Fri, 13 Jan 2017 12:07:33 +0000 (13:07 +0100)]
netifd: update to the latest version

This disables IGMP snooping by default, which was causing various issues
over time, like FS#95

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoimage.mk: use LINUX_KARCH rather than ARCH for mkits
Ian Pozella [Mon, 26 Sep 2016 14:06:10 +0000 (15:06 +0100)]
image.mk: use LINUX_KARCH rather than ARCH for mkits

The generated 'its' is passed to mkimage which expects linux arch
strings rather than the full arch (e.g. mips not mipsel).

It currently works in some cases where LINUX_KARCH == ARCH but
otherwise you get an unknown arch build error.

Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agouqmi: mark as nonshared because of the usb dependencies
Felix Fietkau [Fri, 13 Jan 2017 11:07:53 +0000 (12:07 +0100)]
uqmi: mark as nonshared because of the usb dependencies

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoumbim: mark as nonshared because of the usb dependencies
Felix Fietkau [Fri, 13 Jan 2017 11:07:32 +0000 (12:07 +0100)]
umbim: mark as nonshared because of the usb dependencies

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agocomgt: mark as nonshared because of the usb dependencies
Felix Fietkau [Fri, 13 Jan 2017 11:07:06 +0000 (12:07 +0100)]
comgt: mark as nonshared because of the usb dependencies

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agopolarssl: remove package
Felix Fietkau [Fri, 13 Jan 2017 10:39:56 +0000 (11:39 +0100)]
polarssl: remove package

The mbedTLS 1.3 branch has been EOL since end of 2016 and now all
remaining users have been converted.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoarmvirt: add kernel config change missing from 0d44f0cb
Felix Fietkau [Fri, 13 Jan 2017 09:56:29 +0000 (10:56 +0100)]
armvirt: add kernel config change missing from 0d44f0cb

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoar71xx: default to external USB power on RB-912UAG
Felix Fietkau [Thu, 12 Jan 2017 14:16:02 +0000 (15:16 +0100)]
ar71xx: default to external USB power on RB-912UAG

There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agobuild: let make check warn about use of legacy PKG_MD5SUM variable in feeds
Felix Fietkau [Thu, 12 Jan 2017 14:18:11 +0000 (15:18 +0100)]
build: let make check warn about use of legacy PKG_MD5SUM variable in feeds

The variable rename change has been merged in OpenWrt now, so it's
possible to convert the feeds as well.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agocmake: properly pass host cflags/ldflags to the build
Felix Fietkau [Thu, 12 Jan 2017 13:41:01 +0000 (14:41 +0100)]
cmake: properly pass host cflags/ldflags to the build

This should hopefully fix build issues where libraries that we ship in
tools/ were accidentally picked up from other places on the system, e.g.
/usr/local

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agocmake: support verbose build that shows compiler commands
Felix Fietkau [Thu, 12 Jan 2017 13:32:02 +0000 (14:32 +0100)]
cmake: support verbose build that shows compiler commands

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agocmake: restore parallel build support for bootstrap
Felix Fietkau [Thu, 12 Jan 2017 13:31:40 +0000 (14:31 +0100)]
cmake: restore parallel build support for bootstrap

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agox86/64: enable the fusion scsi driver
Felix Fietkau [Wed, 11 Jan 2017 22:35:37 +0000 (23:35 +0100)]
x86/64: enable the fusion scsi driver

Is it used by VMware Fusion by default. This allows images to boot
without further config changes in VMware.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomac80211: fix broken spatial multiplexing defaults
Felix Fietkau [Wed, 11 Jan 2017 22:35:19 +0000 (23:35 +0100)]
mac80211: fix broken spatial multiplexing defaults

Most mac80211 drivers leave the SMPS field in the HT capabilities
uninitialized (unfortunately defaults to static SMPS), which leads to
some devices limiting themselves to single-stream rates in some modes
(mostly mesh and IBSS).

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoath10k-fw: Update to latest CT firmware
Ben Greear [Tue, 10 Jan 2017 23:49:42 +0000 (15:49 -0800)]
ath10k-fw: Update to latest CT firmware

For 988X, 9980, 9984 CT firmware.

This should allow IBSS + RSN on at least the 988X firmware,
and includes recent stability fixes for all firmware.

Signed-off-by: Ben Greear <greearb@candelatech.com>
7 years agoath10k-ct: Update to latest CT 4.7 ath10k driver.
Ben Greear [Tue, 10 Jan 2017 23:49:41 +0000 (15:49 -0800)]
ath10k-ct: Update to latest CT 4.7 ath10k driver.

This at least makes it harder to hit some txq related
crashes on firmware restart, a potential memory leak,
and some other fixes.

Signed-off-by: Ben Greear <greearb@candelatech.com>
7 years agoarmvirt: enable the USB feature flag
Felix Fietkau [Fri, 13 Jan 2017 08:15:03 +0000 (09:15 +0100)]
armvirt: enable the USB feature flag

USB devices can be passed through from the host to the guest

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomountd: drop USB related dependencies
Felix Fietkau [Fri, 13 Jan 2017 08:10:47 +0000 (09:10 +0100)]
mountd: drop USB related dependencies

That way we can avoid making it nonshared

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoramips: fix WLI-TX4-AG300N boot and network
Yo Abe [Wed, 11 Jan 2017 18:07:14 +0000 (03:07 +0900)]
ramips: fix WLI-TX4-AG300N boot and network

Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.

The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agoramips: add support for VoCore2
Andrew Yong [Sun, 8 Jan 2017 06:30:10 +0000 (14:30 +0800)]
ramips: add support for VoCore2

This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
7 years agoar71xx: enable serial console on Mikrotik RB411/RB433
David Varga [Tue, 10 Jan 2017 18:12:34 +0000 (19:12 +0100)]
ar71xx: enable serial console on Mikrotik RB411/RB433

This patch adds support for serial console on Mikrotik RB411 and RB433
series devices.

Signed-off-by: David Varga <duvi@duvinet.hu>
[picked from FS#377]
Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agoramips: rt3883: fix typo in pinctrl lna_g_func
Daniel Golle [Fri, 13 Jan 2017 04:41:18 +0000 (05:41 +0100)]
ramips: rt3883: fix typo in pinctrl lna_g_func

Spotted by forum users
https://forum.openwrt.org/viewtopic.php?pid=347439#p347439

Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agomap: take over maintainership
Hans Dedecker [Thu, 12 Jan 2017 11:11:09 +0000 (12:11 +0100)]
map: take over maintainership

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
7 years agoodhcp6c: take over maintainership
Hans Dedecker [Thu, 12 Jan 2017 11:10:18 +0000 (12:10 +0100)]
odhcp6c: take over maintainership

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
7 years agoodhcpd: take over maintainership
Hans Dedecker [Thu, 12 Jan 2017 11:06:11 +0000 (12:06 +0100)]
odhcpd: take over maintainership

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
7 years agoRevert "dnsmasq: change 'add_local_hostname' to use dnsmasq '--interface-name'"
Hans Dedecker [Thu, 12 Jan 2017 09:17:48 +0000 (10:17 +0100)]
Revert "dnsmasq: change 'add_local_hostname' to use dnsmasq '--interface-name'"

This causes problem when a FQDN is configured in /etc/config/system. The
domain name will appear twice in reverse DNS.

Next to that, there seems to be a bug in dnsmasq. From the manual page:

--interface-name=<name>,<interface>[/4|/6]
Return  a  DNS  record  associating  the  name  with  the primary address
on the given interface. This flag specifies an A or AAAA record for the
given name in the same way as an /etc/hosts line, except that the address
is not constant, but taken from the given interface. The interface may be
followed by "/4" or "/6" to specify  that  only  IPv4  or  IPv6 addresses
of the interface should be used. If the interface is down, not configured
or non-existent, an empty record is returned. The matching PTR record is
also created, mapping the interface address to the name. More than one name
may be associated with an interface address by repeating the flag; in that
case the first instance is used for  the  reverse address-to-name mapping.

It does not just create an A/AAAA record for the primary address, it creates
one for all addresses. And what is worse, it seems to actually resolve to the
non-primary address first. This is quite annoying when you use floating IP
addresses (e.g. VRRP), because when the floating IP is on the other device,
SSH failes due to incorrect entry in the known hosts file.

I know that this is not a common setup, but it would be nice if there was an
option to restore the previous behaviour, rather than just forcing this new
feature on everybody.

Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agomap: delete map-t device when tearing down map interface
Hans Dedecker [Thu, 12 Jan 2017 08:53:32 +0000 (09:53 +0100)]
map: delete map-t device when tearing down map interface

Delete the map-t device when tearing down the map-t interface; as such
there's no conflict when the map-t interface comes up again when trying
to add the map-t device as the map-t device was still present
(Can not add: device 'map-wan6_4' already exists!).

Only call ifdown in teardown for map-e and lw6o4 map interfaces types
in order to suppress the trace "wan6_4 (6652): Interface wan6_4_ not found"

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agoRevert the recent dependency and metadata scanning rework
Felix Fietkau [Wed, 11 Jan 2017 18:47:33 +0000 (19:47 +0100)]
Revert the recent dependency and metadata scanning rework

This reverts the following commits:
fbe522d1204149b6c128d55e360bfc15fa8258e1
278ad007ee03c4455c3507322e34b0e3e6ec050d
863888e44f7a1fb1675a2e7a2eaabfec3561d2a2
96daf6352f6e04bc22789466cb5409b93fbec191
cfd83555fc4f0bab18a26f6812da18e64df46ff3

This seems to trigger some mconf bugs when built with all feeds
packages, so I will try to find a less intrusive solution before the
release.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agocomgt: allow build without USB_SUPPORT
Felix Fietkau [Wed, 11 Jan 2017 17:06:06 +0000 (18:06 +0100)]
comgt: allow build without USB_SUPPORT

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoumbim: allow build without USB_SUPPORT
Felix Fietkau [Wed, 11 Jan 2017 17:05:38 +0000 (18:05 +0100)]
umbim: allow build without USB_SUPPORT

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agouqmi: allow build without USB_SUPPORT
Felix Fietkau [Wed, 11 Jan 2017 17:05:16 +0000 (18:05 +0100)]
uqmi: allow build without USB_SUPPORT

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomountd: allow build without USB_SUPPORT
Felix Fietkau [Wed, 11 Jan 2017 17:04:18 +0000 (18:04 +0100)]
mountd: allow build without USB_SUPPORT

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoscripts/package-metadata.pl: fix overriding conditional dependencies with conditional...
Felix Fietkau [Wed, 11 Jan 2017 17:22:56 +0000 (18:22 +0100)]
scripts/package-metadata.pl: fix overriding conditional dependencies with conditional select

Conditional dependencies use the '(!cond) || dep' syntax, whereas
conditional select uses 'dep if cond'.
Add an extra check to suppress emitting a conditional if an equal
conditional select already exists.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoarc770: build dtb files in Image/Prepare so that they are available for Device/*
Felix Fietkau [Wed, 11 Jan 2017 15:25:32 +0000 (16:25 +0100)]
arc770: build dtb files in Image/Prepare so that they are available for Device/*

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoarchs38: build dtb files in Image/Prepare so that they are available for Device/*
Felix Fietkau [Wed, 11 Jan 2017 15:25:48 +0000 (16:25 +0100)]
archs38: build dtb files in Image/Prepare so that they are available for Device/*

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agobcm53xx: backport upstream bcm53xx spi driver changes
Rafał Miłecki [Wed, 11 Jan 2017 14:21:13 +0000 (15:21 +0100)]
bcm53xx: backport upstream bcm53xx spi driver changes

One replaces our local patch and another is just for keeping driver in
sync (license change).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agomvebu: work around an ethernet tx scheduling fairness issue
Felix Fietkau [Wed, 11 Jan 2017 13:55:45 +0000 (14:55 +0100)]
mvebu: work around an ethernet tx scheduling fairness issue

The hardware queue scheduling is apparently configured with fixed
priorities, which creates a nasty fairness issue where traffic from one
CPU can starve traffic from all other CPUs.

Work around this issue by forcing all tx packets to go through one CPU,
until this issue is fixed properly.

Signed-off-by: Felix Fietkau <nbd@nbd.name>