Dinh Nguyen [Wed, 15 Apr 2015 21:44:32 +0000 (16:44 -0500)]
arm: socfpga: spl: add board_init_f to SPL
Remap SDRAM to 0x0, and clear OCRAM's ECC in board_init_f().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Dinh Nguyen [Wed, 15 Apr 2015 21:44:31 +0000 (16:44 -0500)]
arm: socfpga: spl: Add s_init stub
Add a stub s_init function in the board file. The reason why the stub function
is needed is that most of the work is now being done in board_init_f(), there
is no need for the SPL to do anything s_init(). However, since lowlevel_init()
is still branching to s_init(), we need stub function for now, until
lowlevel_init() morphs into s_init().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:18 +0000 (17:01 -0500)]
arm: socfpga: fix uart0 pin mux configuration
commit "
07d30b6c3129 arm: socfpga: Sync Cyclone V DK pinmux configuration"
incorrectly set the muxing for UART0 on the Cyclone V DK.
This fixes it up so UART0 is working again.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:15 +0000 (17:01 -0500)]
arm: socfpga: spl: Add SDRAM check
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:13 +0000 (17:01 -0500)]
arm: socfpga: spl: Adjust the SYS_INIT_RAM_SIZE to have room for the spl malloc
We need to adjust the SYS_INIT_RAM_SIZE to have room for the
SPL_MALLOC_SIZE.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:12 +0000 (17:01 -0500)]
arm: socfpga: spl: add CONFIG_SPL_STACK to socfpga_common.h
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:10 +0000 (17:01 -0500)]
arm: socfpga: spl: Use common lowlevel_init
For SoCFGPA, use the common ARMv7 lowlevel_init. Thus, we can delete the
SoCFPGA lowlevel_init.S file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:09 +0000 (17:01 -0500)]
arm: socfpga: spl: printout sdram size
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:08 +0000 (17:01 -0500)]
arm: socfpga: spl: add sdram init and calibration
Add a call to checkboard along with sdram intilialization and calibration.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:07 +0000 (17:01 -0500)]
arm: socfpga: spl: allow bootrom to enable IOs after warm reset
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:06 +0000 (17:01 -0500)]
arm: socfpga: spl: Add call to timer_init
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:05 +0000 (17:01 -0500)]
arm: socfpga: spl: enable sdram, timer and uart
Add the calls in the spl_board_init to enable SDRAM, timer, and UART.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:04 +0000 (17:01 -0500)]
arm: socfpga: add functions to bring sdram, timer, and uart out of reset
These functions will be needed for use by the SPL for enabling the
console and sdram initialization.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Dinh Nguyen [Mon, 30 Mar 2015 22:01:03 +0000 (17:01 -0500)]
arm: socfpga: spl: Add CONFIG_SPL_MAX_SIZE to be 64KB
The Cyclone5 SoCFPGA has 64KB of OCRAM for SPL use.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tom Rini [Mon, 20 Apr 2015 13:13:52 +0000 (09:13 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Heiko Schocher [Sun, 12 Apr 2015 08:20:19 +0000 (10:20 +0200)]
video, lg4573: add support for the lg4573 display
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Mon, 20 Apr 2015 05:53:48 +0000 (07:53 +0200)]
video, ipu: make ldb clock frequency overwritable through board code
the ldb clock can be setup in board code (for example set through PLL5).
Update the ldb_clock rate also through board code.
This should be removed, if a clock framework is availiable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Heiko Schocher [Mon, 20 Apr 2015 05:52:21 +0000 (07:52 +0200)]
video, ipu: make ldb_clock configurable
make the ldb_clock configurable through the new define
CONFIG_SYS_LDB_CLOCK. This is needed as the ldb clock is not
always
650000000, for example on the aristainetos2 board,
where the ldb clock derives from PLL5 clock.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:27 +0000 (22:54 +0200)]
sandbox: add config_distro_defaults and config_distro_bootcmd
Make the sandbox setup more generic/examplary by including
config_distro_defaults.h and config_distro_bootcmd.h.
Among other things this makes it easy to test whether images will boot
though with the standard distro bootcmds by running e.g:
u-boot -c 'host bind 0 myimage.img ; boot'
By default there are 2 target host devices to emulate device with
multiple storage devices (e.g. internal ("host 0") and external
("host 1") and verify that the prioritization and fallbacks do work
correctly.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:26 +0000 (22:54 +0200)]
config: Add default client arch defines for intel architectures
Define default PXE client architecture identifiers for IA32 (0x0 aka
Intel x86PC) and Intel x86-64 (0x9 aka EFI x86-64).
This prepares for usage for config_distro_defaults in the sandbox
architecture
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:25 +0000 (22:54 +0200)]
pxe: Ensure all memory access is to mapped memory
Properly map memory through map_sysmem so that pxe can be used from the
sandbox.
Tested in sandbox as well as on jetson-tk1, odroid-xu3, snow as peach-pi
boards
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:24 +0000 (22:54 +0200)]
config_distro_bootcmd.h: Add shared block definition for the host interface
Define the common shared block environment for the host interface in
preperation for the sandbox build to use config_distro_bootcmd.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:23 +0000 (22:54 +0200)]
sandbox: Implement host dev [device]
A common pattern to check if a certain device exists (e.g. in
config_distro_bootcmd) is to use: <interface> dev [device]
Implement host dev [device] so this pattern can be used for sandbox host
devices.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:22 +0000 (22:54 +0200)]
sandbox: Renamed sb command to host
As suggested by Simon Glass, rename the sb command to host but keep the
old sb command as an alias
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:21 +0000 (22:54 +0200)]
sandbox: Add support for bootz
Add dummy bootz_setup implementation allowing the u-boot sandbox to
run bootz. This recognizes both ARM and x86 zImages to validate a
valid zImage was loaded.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:20 +0000 (22:54 +0200)]
sandbox: Split bootm code out into lib/bootm
Follow the convention of other architectures and move the platform
specific linux bootm code into sandbox/lib/bootm.c.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Mon, 13 Apr 2015 20:54:19 +0000 (22:54 +0200)]
sandbox: only do sandboxfs for hostfs interface
Only do sandbox filesystem access when using the hostfs device
interface, rather then falling back to it in all cases. This prevents
confusion situations due to the fallback being taken rather then an
unsupported error being raised.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 18 Apr 2015 23:24:13 +0000 (19:24 -0400)]
Merge branch 'buildman' of git://git.denx.de/u-boot-x86
Wu, Josh [Fri, 3 Apr 2015 02:51:17 +0000 (10:51 +0800)]
patman: cover letter shows like 00/xx if more than 10 patches
Make cover letter shows like 0/x, 00/xx and 000/xxx etc.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 1 Apr 2015 11:47:41 +0000 (07:47 -0400)]
buildman: Make -V (verbose_build) really be verbose
The help text for -V says we will pass V=1 but all it really did was not
pass in -s. Change the logic to pass make V=1 with given to buildman -V or
-s to make otherwise.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 20 Mar 2015 14:50:38 +0000 (10:50 -0400)]
buildman: Keep more outputs with the --keep-outputs flag
When told to keep outputs, be much more liberal in what files we keep.
In addition to adding 'MLO', keep anything that matches u-boot-spl.* (so
that we keep the map file as well) and anything we generate about
'u-boot itself. A large number of bootable formats now match this and
thus it's easier to build many targets and then boot them afterwards
using buildman.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Feb 2015 05:06:15 +0000 (22:06 -0700)]
buildman: Allow comparison of build configuration
It is useful to be able to see CONFIG changes made by commits. Add this
feature to buildman using the -K flag so that all CONFIG changes are
reported.
The CONFIG options exist in a number of files. Each is reported
individually as well as a summary that covers all files. The output
shows three parts: green for additions, red for removals and yellow for
changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Feb 2015 05:06:14 +0000 (22:06 -0700)]
buildman: Store build config files
Store all config file output so that we can compare changes if requested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Feb 2015 05:06:13 +0000 (22:06 -0700)]
buildman: Adjust the 'aborted' heuristic for writing output
At present buildman tries to detect an aborted build and doesn't record a
result in that case. This is to make sure that an abort (e.g. with Ctrl-C)
does not mark the build as done. Without this option, buildman would never
retry the build unless -f/-F are provided. The effect is that aborting the
build creates 'fake errors' on whatever builds buildman happens to be
working on at the time.
Unfortunately the current test is not reliable and this detection can
trigger if a required toolchain tool is missing. In this case the toolchain
problem is never reported.
Adjust the logic to continue processing the build result, mark the build as
done (and failed), but with a return code which indicates that it should be
retried.
The correct fix is to fully and correctly detect an aborted build, quit
buildman immediately and not write any partial build results in this case.
Unfortunately this is currently beyond my powers and is left as an exercise
for the reader (and patches are welcome).
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Feb 2015 05:06:12 +0000 (22:06 -0700)]
buildman: Show 'make' command line when -V is used
When a verbose build it selected, show the make command before the output of
that command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Feb 2015 05:06:10 +0000 (22:06 -0700)]
Create a .cfg file containing the CONFIG options used to build
At present CONFIG options are split across Kconfig and board config headers
files. Also we have multiple files containing these CONFIG options.
In order to see exactly what is being used for building, create a .cfg
file which holds these options as reported by the C preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Scott Wood [Fri, 17 Apr 2015 14:19:01 +0000 (09:19 -0500)]
ahci: mmio_base is a virtual address
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes
284231e49a2b4 ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Simon Glass [Fri, 6 Mar 2015 20:19:14 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_SOUND_SANDBOX to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:13 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_SOUND_WM8994 to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:12 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_SOUND_MAX98095 to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:11 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_I2S_SAMSUNG to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:10 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_I2S to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:09 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_CMD_SOUND to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:08 +0000 (13:19 -0700)]
sandbox: exynos: Move CONFIG_SOUND to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:07 +0000 (13:19 -0700)]
sandbox: Move CONFIG_TPM_TIS_SANDBOX to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:06 +0000 (13:19 -0700)]
sandbox: Move CONFIG_SPI_FLASH_SANDBOX to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:05 +0000 (13:19 -0700)]
sandbox: Move CONFIG_SANDBOX_SPI to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:04 +0000 (13:19 -0700)]
sandbox: Move CONFIG_SYS_I2C_SANDBOX to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher<hs@denx.de>
Simon Glass [Fri, 6 Mar 2015 20:19:02 +0000 (13:19 -0700)]
sandbox: Move CONFIG_SYS_VSNPRINTF to Kconfig
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Mar 2015 20:19:01 +0000 (13:19 -0700)]
sandbox: Move GPIO CONFIGs to Kconfig
Move these over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 3 Mar 2015 00:04:37 +0000 (17:04 -0700)]
Kconfig: Move CONFIG_BOOTSTAGE to Kconfig
Move CONFIG_BOOT_STAGE and its associated options to Kconfig. Adjust
existing users and code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 5 Apr 2015 22:07:43 +0000 (16:07 -0600)]
dm: sunxi: Use driver model for Ethernet on Linksprite pcDuino3
Switch this board over to use driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 5 Apr 2015 22:07:42 +0000 (16:07 -0600)]
dm: sunxi: Support driver model for Ethernet
Adjust the Ethernet initialisation code to support driver model.
It is no-longer necessary to call designware_initialize(). The device will
be probed when it is used. The PHY type and GMAC base will come from the
device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 5 Apr 2015 22:07:41 +0000 (16:07 -0600)]
dm: net: Adjust designware driver to support driver model
Add driver model support to the designware driver. This reuses most of the
existing code except for some duplication in the probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 5 Apr 2015 22:07:40 +0000 (16:07 -0600)]
dm: net: Tidy up designware driver ready for driver model
Adjust the error handling to use errno.h instead of returning -1. Change
leaf functions to pass in the arguments they require rather than struct
eth_device. Apart from simplifying the code it makes is easier to reuse
these functions for driver model, since mostly they actually only use
struct dw_eth_priv (which we can keep).
Create a stub for each Ethernet operation function. This will allow use to
share code with the driver model versions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 5 Apr 2015 22:07:39 +0000 (16:07 -0600)]
dm: net: Adjust PHY interface to work with CONFIG_DM_ETH
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 5 Apr 2015 22:07:38 +0000 (16:07 -0600)]
Avoid calling print_eths() with driver model
This function is not supported with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 5 Apr 2015 22:07:37 +0000 (16:07 -0600)]
dm: net: Use existing Ethernet init for driver model
At present even with driver model is used there is still much manual init
of related devices: PHY, environment and board init. Until these requirements
are dealt with in another way we need to keep them around.
Break out the init portion of the legacy eth_initialize() into a separate
function and call it from both the legacy and driver model eth_initialize()
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 5 Apr 2015 22:07:35 +0000 (16:07 -0600)]
dts: sunxi: Bring in Ethernet device tree bindings
Since we will use these bindings on sunxi, bring them in from Linux
4.0-rc1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Simon Glass [Sun, 5 Apr 2015 22:07:34 +0000 (16:07 -0600)]
Kconfig: Move CONFIG_DESIGNWARE_ETH to Kconfig
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 5 Apr 2015 22:07:33 +0000 (16:07 -0600)]
sunxi: Replace the pcDuino3 config with FDT version
We currently have Linksprite_pcDuino3 and Linksprite_pcDuino3_fdt. Drop the
former in favour of the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Joe Hershberger [Wed, 8 Apr 2015 06:41:25 +0000 (01:41 -0500)]
sandbox: Enable more network features for sandbox
More net features enabled and supported on sandbox to allow more testing
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:24 +0000 (01:41 -0500)]
net: Fix compile errors when SNTP enabled and not DATE
When SNTP is enabled and DATE is not, to_tm() is not built in. It could
be defined when TIMESTAMP is defined, so check for that.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sergey Temerkhanov [Wed, 8 Apr 2015 06:41:23 +0000 (01:41 -0500)]
net: Convert protocol structures to use explicit sizes
Convert uchar/ushort to u8/u16 respectively.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sergey Temerkhanov [Wed, 8 Apr 2015 06:41:22 +0000 (01:41 -0500)]
net: Fix incorrect DHCP/BOOTP packets on 64-bit systems
This commit fixes incorrect DHCP/BOOTP packet layout caused by
'ulong' type size difference on 64 and 32-bit architectures.
It also renames NetReadLong()/NetCopyLong() to
net_read_u32/net_copy_u32() accordingly.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:21 +0000 (01:41 -0500)]
net: cosmetic: Fix checkpatch.pl failures in net.c
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:20 +0000 (01:41 -0500)]
net: cosmetic: Fix checkpatch.pl failures in net.h
There were still a few remaining complains in the legacy eth_device
definition that hadn't been addressed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:19 +0000 (01:41 -0500)]
net: cosmetic: Fix checkpatch.pl failures in eth.c
There were still a few failures in net/eth.c, especially in the legacy
part of the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:18 +0000 (01:41 -0500)]
net: cosmetic: Fix checkpatch.pl failures in linklocal
A few new rules in checkpatch.pl since linklocal.c was added.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:17 +0000 (01:41 -0500)]
net: cosmetic: Clean up cmd_net variables and functions
Make a thorough pass through all variables and function names contained
within common/cmd_net.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:16 +0000 (01:41 -0500)]
net: cosmetic: Clean up netconsole variables and functions
Make a thorough pass through all variables and function names contained
within netconsole.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:15 +0000 (01:41 -0500)]
net: cosmetic: Clean up DNS variables and functions
Make a thorough pass through all variables and function names contained
within dns.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:14 +0000 (01:41 -0500)]
net: cosmetic: Clean up CDP variables and functions
Make a thorough pass through all variables and function names contained
within cdp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:13 +0000 (01:41 -0500)]
net: cosmetic: Clean up ping variables and functions
Make a thorough pass through all variables and function names contained
within ping.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:12 +0000 (01:41 -0500)]
net: cosmetic: Clean up SNTP variables and functions
Make a thorough pass through all variables and function names contained
within sntp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:11 +0000 (01:41 -0500)]
net: cosmetic: Clean up RARP variables and functions
Make a thorough pass through all variables and function names contained
within rarp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:10 +0000 (01:41 -0500)]
net: cosmetic: Clean up NFS variables and functions
Make a thorough pass through all variables and function names contained
within nfs.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:09 +0000 (01:41 -0500)]
net: cosmetic: Clean up DHCP variables and functions
Make a thorough pass through all variables and function names contained
within bootp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:08 +0000 (01:41 -0500)]
net: cosmetic: Clean up ARP variables and functions
Make a thorough pass through all variables and function names contained
within arp and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:07 +0000 (01:41 -0500)]
net: cosmetic: Clean up TFTP variables and functions
Make a thorough pass through all variables and function names contained
within tftp and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:06 +0000 (01:41 -0500)]
net: cosmetic: Fix var naming net <-> eth drivers
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:05 +0000 (01:41 -0500)]
net: cosmetic: Cleanup internal packet buffer names
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 8 Apr 2015 06:41:04 +0000 (01:41 -0500)]
net: cosmetic: Name ethaddr variables consistently
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:03 +0000 (01:41 -0500)]
net: cosmetic: Fixup var names for DHCP strings
Remove CamelCase variable naming.
Move the definition to the same compilation unit as the primary use.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:02 +0000 (01:41 -0500)]
net: cosmetic: Fixup var names related to boot file
The variables around the bootfile were inconsistent and used CamelCase.
Update them to make the code more readable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 8 Apr 2015 06:41:01 +0000 (01:41 -0500)]
net: cosmetic: Change IPaddr_t to struct in_addr
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:48:03 +0000 (12:48 +0900)]
powerpc: ids8313: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:48:02 +0000 (12:48 +0900)]
ARM: cm_fx6: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:48:01 +0000 (12:48 +0900)]
ARM: stv0991: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:48:00 +0000 (12:48 +0900)]
ARM: bav335x: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:59 +0000 (12:47 +0900)]
ARM: socfpga: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:58 +0000 (12:47 +0900)]
ARM: mx6: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:57 +0000 (12:47 +0900)]
ARM: snapper9260: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:56 +0000 (12:47 +0900)]
ARM: rmobile: use "select" instead of default value in defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:55 +0000 (12:47 +0900)]
ARM: zynq: use "select" instead of default value in defconfig
All the Zynq boards have switch to Driver Model.
"select DM" is better than default value in each defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:54 +0000 (12:47 +0900)]
ARM: UniPhier: use "select" instead of default value in defconfig
All the UniPhier boards have switch to Driver Model.
"select DM" is better than default value in each defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:53 +0000 (12:47 +0900)]
dm: select CONFIG_DM* options
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 31 Mar 2015 03:47:52 +0000 (12:47 +0900)]
dm: spi_flash: fix wrong dependency
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way. See below.)
Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.
On the other hand, all the Tegra boards enable DM_SPI_FLASH because
config DM_SPI_FLASH
default y
silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 25 Mar 2015 18:23:08 +0000 (12:23 -0600)]
dm: usb: Add a README for driver model
Add some documentation describing how USB is implemented with USB. This
might make things easier for people to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 25 Mar 2015 18:23:05 +0000 (12:23 -0600)]
dm: usb: Add tests for the USB uclass
This adds a simple test for probing and a functional test using the flash
stick emulator, which tests a large chunk of the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>