Mike Frysinger [Sat, 28 Mar 2009 10:41:09 +0000 (06:41 -0400)]
sf: always read 5 bytes for the idcode
Some SPI flash drivers like to have extended id information available
(like the spansion flash), so rather than making it re-issue the ID cmd
to get at the last 2 bytes, have the common code read 5 bytes rather than
just 3. This also matches the Linux behavior where it always reads 5 id
bytes from all flashes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Mingkai Hu <Mingkai.hu@freescale.com>
Mike Frysinger [Fri, 27 Mar 2009 20:34:21 +0000 (16:34 -0400)]
sf: stmicro: drop redundant id read
The common SPI flash code reads the idcode and passes it down to the SPI
flash driver, so there is no need to read it again ourselves.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Mike Frysinger [Fri, 27 Mar 2009 23:27:58 +0000 (19:27 -0400)]
sf: add driver for SST flashes
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Mike Frysinger [Tue, 24 Mar 2009 03:03:58 +0000 (23:03 -0400)]
sf: drop DEBUG defines
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 4 Jan 2009 06:44:07 +0000 (07:44 +0100)]
mtd: add some at45 spi flash support
- AT45DB321D
- AT45DB161D
- AT45DB081D
- AT45DB041D
- AT45DB021D
- AT45DB011D
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mingkai Hu [Tue, 31 Mar 2009 06:09:41 +0000 (14:09 +0800)]
mtd: SPI Flash: Support the Spansion Flash
Add MTD SPI Flash support for S25FL008A, S25FL016A,
S25FL032A, S25FL064A, S25FL128P.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Wed, 1 Apr 2009 22:24:33 +0000 (00:24 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Scott Wood [Tue, 31 Mar 2009 22:49:36 +0000 (17:49 -0500)]
mpc83xx: Set guarded bit on BAT that covers the end of the address space
The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of
address space; however, not all of this space is covered by a device. In
particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped
at the far end of the address space.
In zlib, there is a loop that references p[-1] if p is non-NULL. Under
some circumstances, this leads to the CPU speculatively loading from
0xfffffff8 if p is NULL. This leads to a machine check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
continuation to the remaining mpc83xx boards that suffer from the same problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Wed, 1 Apr 2009 20:47:03 +0000 (22:47 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Wolfgang Denk [Wed, 1 Apr 2009 20:43:51 +0000 (22:43 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Kim Phillips [Mon, 30 Mar 2009 19:28:05 +0000 (14:28 -0500)]
rtc: remove broken rtc_read and rtc_write declarations
commit
04e11cf3 "rtc: add support for 4543 RTC (manufactured by e.g.
EPSON)" introduces the following build error on boards configuring e.g,
the ds1374 rtc:
Configuring for MPC837XEMDS board...
ds1374.c:103: error: static declaration of 'rtc_read' follows non-static declaration
/home/r1aaha/git/u-boot/include/rtc.h:64: error: previous declaration of 'rtc_read' was here
ds1374.c:104: error: conflicting types for 'rtc_write'
/home/r1aaha/git/u-boot/include/rtc.h:65: error: previous declaration of 'rtc_write' was here
this reverts the erroneous chunk.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Detlev Zundel <dzu@denx.de>
CC: Andreas Pfefferle <ap@denx.de>
Kumar Gala [Tue, 31 Mar 2009 22:58:13 +0000 (17:58 -0500)]
85xx/86xx: Ensure MP boot page is not used
We had a bug on 86xx in which the boot page used to bring up secondary
cores was being overwritten and used for the malloc region in u-boot.
We need to reserve the region of memory that the boot page is going to
be put at so nothing uses it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Kumar Gala [Wed, 1 Apr 2009 04:11:05 +0000 (23:11 -0500)]
85xx: Introduce determine_mp_bootpg() helper.
Match determine_mp_bootpg() that was added for 86xx. We need this to
address a bug introduced in v2009.03 with 86xx MP booting. We have to
make sure to reserve the region of memory used for the MP bootpg() so
other u-boot code doesn't use it.
Also added a comment about how cpu_reset() is dealing w/an errata on
early 85xx MP HW.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 1 Apr 2009 04:02:38 +0000 (23:02 -0500)]
86xx: Cleanup MP support
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper. We'll need this to address a
bug introduced in v2009.03 with 86xx MP booting. We have to make sure
to reserve the region of memory used for the MP bootpg() so other
u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
allow cmd_mp.c to build and work. In the future we should look at
implementing all these functions. This could be common w/85xx if we
use spin tables on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Becky Bruce [Tue, 31 Mar 2009 23:38:37 +0000 (18:38 -0500)]
mpc8641hpcn/sbc8641d: Add missing board_lmb_reserves
We're missing the board_lmb_reserve definitions that allow
cpu_mp_lmb_reserve to be called; this means that Linux
is free to reallocate reserved pages. Linux currently boots
because we're getting lucky - the page we've reserved is
high enough in memory that it isn't allocated by Linux
while we still need it to be in existence.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ladislav Michl [Tue, 31 Mar 2009 11:43:10 +0000 (13:43 +0200)]
NetStar: fix NAND
Fix NAND support broken during new NAND code merge. Move those few lines of
code to board/netstar/netstar.c
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Jens Scharsig [Tue, 31 Mar 2009 06:18:29 +0000 (08:18 +0200)]
soft_i2c.c compiler/linker error
This patch fix the compiler/linker errors
common/cmd_i2c.c:1252: undefined reference to `i2c_get_bus_speed'
common/cmd_i2c.c:1256: undefined reference to `i2c_set_bus_speed'
if board use CONFIG_I2C_CMD_TREE and CONFIG_I2C_MULTI_BUS is not
uesd/undef (wrong define order)
and
removes additional empty lines
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Haiying Wang [Fri, 27 Mar 2009 21:02:45 +0000 (17:02 -0400)]
MPC85xx: Add MPC8569MDS board support
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Haiying Wang [Fri, 27 Mar 2009 21:02:44 +0000 (17:02 -0400)]
MPC85xx: Add MPC8569 CPU support
There is a workaround for MPC8569 CPU Errata, which needs to set Bit 13 of
LBCR in 4K bootpage. We setup a temp TLB for eLBC controller in bootpage,
then invalidate it after LBCR bit 13 is set.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Haiying Wang [Thu, 26 Mar 2009 21:01:49 +0000 (17:01 -0400)]
MPC85xx: Load and enable QE microcode patch in IRAM
For the silicon which doesn't have ROM support in QE, it always needs to load
a pre-built ucode binary to IRAM so that QE can work.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Kumar Gala [Thu, 19 Mar 2009 14:16:10 +0000 (09:16 -0500)]
85xx: Add support for additional e500mc features
* Enable backside L2
* e500mc no longer has timebase enable in HID (moved to CCSR register)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Sat, 14 Mar 2009 04:48:30 +0000 (12:48 +0800)]
fsl-ddr: add the DDR3 SPD infrastructure
- support mirrored DIMMs, not support register DIMMs
- test passed on P2020DS board with MT9JSF12872AY-1G1D1
- test passed on MPC8569MDS board with MT8JSF12864HY-1G1D1
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Travis Wheatley <travis.wheatley@freescale.com>
Dave Liu [Sat, 14 Mar 2009 04:48:19 +0000 (12:48 +0800)]
fsl-ddr: Fix two bugs in the ddr infrastructure
1. wr_lat
UM said the total write latency for DDR2 is equal to
WR_LAT + ADD_LAT, the write latency is CL + ADD_LAT - 1.
so, the WR_LAT = CL - 1;
2. rd_to_pre
we missed to add the ADD_LAT for DDR2 case.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Kumar Gala [Thu, 26 Mar 2009 06:34:39 +0000 (01:34 -0500)]
83xx: Use common LSDMR defines from asm/fsl_lbc.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Kumar Gala [Thu, 26 Mar 2009 06:34:38 +0000 (01:34 -0500)]
85xx: Use common LSDMR defines from asm/fsl_lbc.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 26 Mar 2009 06:34:37 +0000 (01:34 -0500)]
Add LSDMR (SDRAM Mode Register) definition on localbus
The masks for various bit defines of LSDMR are common and thus we can
define them in one place rather than replicating them in each config.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ladislav Michl [Mon, 30 Mar 2009 16:58:41 +0000 (18:58 +0200)]
OMAP: use {read,write}l to access timer registers
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Mon, 30 Mar 2009 16:58:41 +0000 (18:58 +0200)]
OMAP: rename timer divisor
Divisor field is called PTV not PVT.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Ladislav Michl [Mon, 30 Mar 2009 16:58:40 +0000 (18:58 +0200)]
OMAP: reindent timer code
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 16:58:40 +0000 (18:58 +0200)]
s3c2410: move nand driver to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 16:58:40 +0000 (18:58 +0200)]
s3c24x0: move i2c driver to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 16:58:39 +0000 (18:58 +0200)]
s3c24x0: move serial driver to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 16:58:39 +0000 (18:58 +0200)]
davinci: move i2c driver to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 16:58:39 +0000 (18:58 +0200)]
davinci: move nand driver to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 30 Mar 2009 16:58:38 +0000 (18:58 +0200)]
imx: move serial driver to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Detlev Zundel [Sun, 29 Mar 2009 22:31:36 +0000 (00:31 +0200)]
inka4x0: Use proper accessor macros for memory mapped registers.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Detlev Zundel [Sun, 29 Mar 2009 22:31:35 +0000 (00:31 +0200)]
inka4x0: Add hardware diagnosis and RTC in configuration.
This patch adds the board specific communication routines needed by
the external 4543 RTC.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Detlev Zundel [Sun, 29 Mar 2009 22:31:34 +0000 (00:31 +0200)]
inka4x0: Add hardware diagnosis functions for inka4x0
This patch adds advanced diagnosis functions for the inka4x0 board.
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Detlev Zundel [Sun, 29 Mar 2009 22:31:33 +0000 (00:31 +0200)]
rtc: add support for 4543 RTC (manufactured by e.g. EPSON)
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Detlev Zundel [Sun, 29 Mar 2009 22:31:32 +0000 (00:31 +0200)]
drivers/twserial: Add protocol driver for "three wire serial" interface.
This pretty unintelligent interface is used on some RTC chips.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:42 +0000 (23:01 +0200)]
arm720t/clps7111: move serial driver to drivers/serial
add CONFIG_CLPS7111_SERIAL to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:42 +0000 (23:01 +0200)]
lpc2292: move serial driver to drivers/serial
add CONFIG_LPC2292_SERIAL to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:42 +0000 (23:01 +0200)]
ks8695: move serial driver to drivers/serial
add CONFIG_KS8695_SERIAL to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:42 +0000 (23:01 +0200)]
s3c64xx: move usb driver to drivers/usb
add CONFIG_USB_S3C64XX to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:41 +0000 (23:01 +0200)]
imx31: move serial driver to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:41 +0000 (23:01 +0200)]
netarm: move serial driver to drivers/serial
add CONFIG_NETARM_SERIAL to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:41 +0000 (23:01 +0200)]
sa1100: move serial driver to drivers/serial
add CONFIG_SA1100_SERIAL to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:41 +0000 (23:01 +0200)]
s3c44b0: extract cache from cpu.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:41 +0000 (23:01 +0200)]
s3c44b0: move serial driver to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:40 +0000 (23:01 +0200)]
s3c44b0: move rtc driver to drivers/rtc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:40 +0000 (23:01 +0200)]
s3c44b0: move i2c driver to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 29 Mar 2009 21:01:36 +0000 (23:01 +0200)]
s3c4510b: move specific code to soc directory
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Ladislav Michl [Wed, 25 Mar 2009 22:43:58 +0000 (23:43 +0100)]
NetStar: add RTC support
Add RTC support.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Wed, 25 Mar 2009 22:43:50 +0000 (23:43 +0100)]
NetStar: use generic flash driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Mon, 16 Mar 2009 22:31:20 +0000 (23:31 +0100)]
NetStar: update crcit utility
Make crc32 function to match its prototype. Use more meaningful identifiers.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Ladislav Michl [Mon, 23 Mar 2009 16:46:27 +0000 (17:46 +0100)]
Remove nowhere used symbol CONFIG_SYS_CLKS_IN_HZ
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Wolfgang Denk [Sat, 28 Mar 2009 23:58:16 +0000 (00:58 +0100)]
VCMA9: fix compile errors
Fix these:
cmd_vcma9.c:82: warning: implicit declaration of function 'eth_getenv_enetaddr'
cmd_vcma9.c:89: error: 'enetaddr' undeclared (first use in this function)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 28 Mar 2009 23:54:21 +0000 (00:54 +0100)]
ARM: fix warning: 'print_eth' defined but not used
This warning got issued for all ARM systems that don't have
CONFIG_CMD_NET enabled.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Ladislav Michl [Mon, 23 Mar 2009 17:16:34 +0000 (18:16 +0100)]
cs8900 compile fix
cs8900.c: In function 'eth_init':
cs8900.c:164: warning: passing argument 2 of 'eth_getenv_enetaddr' from incompatible pointer type
cs8900.c:165: error: invalid operands to binary <<
cs8900.c:166: error: invalid operands to binary <<
cs8900.c:167: error: invalid operands to binary <<
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sat, 28 Mar 2009 19:16:16 +0000 (20:16 +0100)]
Fix implicit declaration of function 'eth_[gs]etenv_enetaddr'
...and some other compile warnings.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 28 Mar 2009 15:17:29 +0000 (16:17 +0100)]
mpc8xx/ether.c: fix warning: unused variable 'bd'
Also minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Detlev Zundel [Wed, 25 Mar 2009 16:27:52 +0000 (17:27 +0100)]
command.c: Expose the core of do_help as _do_help to the rest of u-boot.
Other commands implementing subcommands can reuse this code nicely.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Detlev Zundel [Tue, 24 Mar 2009 17:02:33 +0000 (18:02 +0100)]
mpc5xxx: Add structure definition for several more register blocks.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Detlev Zundel [Fri, 27 Mar 2009 14:03:55 +0000 (15:03 +0100)]
MAINTAINERS: Add entry for 'inka4x0' board.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Detlev Zundel [Fri, 27 Mar 2009 14:03:54 +0000 (15:03 +0100)]
MAINTAINERS: Keep list sorted.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Mike Frysinger [Thu, 26 Mar 2009 15:17:41 +0000 (11:17 -0400)]
karef/metrobox/xpedite1k: fix eth_setenv_enetaddr typos
The function is called "eth_setenv_enetaddr", not "eth_putenv_enetaddr".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
Heiko Schocher [Thu, 26 Mar 2009 06:33:59 +0000 (07:33 +0100)]
ppc: cleanup compiler errors/warnings
Current u-boot top of tree builds with warnings/errors for
the following boards:
ads5121 cpci5200 mecp5200 v38b IAD210 MBX MBX860T NX823
RPXClassic debris PN62
following patch solves this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Thu, 26 Mar 2009 21:28:52 +0000 (22:28 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Thu, 26 Mar 2009 21:27:45 +0000 (22:27 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-at91
Wolfgang Denk [Thu, 26 Mar 2009 21:21:48 +0000 (22:21 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Stefan Roese [Thu, 26 Mar 2009 15:14:13 +0000 (16:14 +0100)]
ppc4xx: Sequoia: Fix TLB reassignment in NAND booting code
This patch fixes a bug in the Sequoia TLB init code to reconfigure
the correct TLB (boot space) after running from RAM. This bug was
introduced with patch
4d332dbeb08f5863d1ea69d91a00c5499d3a87ed
[ppc4xx: Make Sequoia boot vxWorks] which changed the order of the
TLB in the Sequoia init.S file.
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Thu, 26 Mar 2009 09:00:57 +0000 (10:00 +0100)]
ads5121: enable instruction cache
Enabling the instruction cache significantly accelerates U-Boot
operations like CRC checking, image uncompression, etc.
Kudos to Andrea Scian for pointing out.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jon Smirl [Mon, 23 Mar 2009 02:55:45 +0000 (22:55 -0400)]
mpc5200: suppress printf until console initialized
On boards which have the environment in eeprom, i2c_init() is called
before the console and RAM are initialized.
Suppress printfs until the console is initialized.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Wed, 25 Mar 2009 21:43:25 +0000 (22:43 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Guennadi Liakhovetski [Wed, 25 Mar 2009 10:36:50 +0000 (11:36 +0100)]
ARM: Add the imx31_phycore_eet board to MAKEALL
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Nishanth Menon [Wed, 25 Mar 2009 21:13:56 +0000 (22:13 +0100)]
OMAP3:Beagle: Enable mtdparts
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts
provides a flexible way to create and maintain u-boot mtd
partitions. This allows commands such as "nand erase fs"
to work and the user no longer needs to decode the absolute
nand offsets. This patch enables this function for beagleboard
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Mike Frysinger [Sun, 22 Feb 2009 21:26:35 +0000 (16:26 -0500)]
Blackfin: bf537-stamp: split post code out into dedicated post.c
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:51:56 +0000 (22:51 -0400)]
Blackfin: add support for S25FL128 parts
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:51:23 +0000 (22:51 -0400)]
Blackfin: overhaul SPI flash handling to speed things up
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:51:05 +0000 (22:51 -0400)]
Blackfin: add support for SST SPI flashes
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:50:10 +0000 (22:50 -0400)]
Blackfin: add hack for crappy m25p80
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 22 Jan 2009 01:47:12 +0000 (20:47 -0500)]
Blackfin: bf537-stamp: increase monitor size
The new jffs2 code pushed the code size just over the limit, so increase
the limit a bit more.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 8 Dec 2008 21:16:11 +0000 (16:16 -0500)]
Blackfin: bf537-stamp: bump default SCLK up to 125MHz
Since all of the bf537-stamp and bf537-ezkit boards out there can handle it,
increase the speed of SCLK to 125MHz rather than 100MHz.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:44:14 +0000 (22:44 -0400)]
Blackfin: bf537-stamp: rewrite MAC-in-flash handling
Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 9 Dec 2008 18:47:39 +0000 (13:47 -0500)]
Blackfin: add clkin_hz= to default kernel command line for ADI boards
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 13 Oct 2008 03:49:13 +0000 (23:49 -0400)]
Blackfin: bf533-stamp: bump up default clocks
Since the hardware can handle it, bump the default clocks from 80mhz SCLK
and 398mhz CCLK to 100mhz SCLK and 498mhz CCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:40:22 +0000 (22:40 -0400)]
Blackfin: bf533-stamp: rewrite startup LED notifications
Again, don't clobber pins that we aren't actually using, and use the common
LED framework rather than our own hob-job-but-not-really-working.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 1 Jun 2008 13:09:48 +0000 (09:09 -0400)]
Blackfin: unify common ADI board settings
Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that. This
will also make merging the ~10 boards I have to forward port a lot easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Kyungmin Park [Tue, 3 Mar 2009 00:05:53 +0000 (09:05 +0900)]
Reduce OneNAND IPL common code
OneNAND IPL has common codes for RAM init, load data, and jump to 2nd
bootloader, but it's common code used about 300~400 bytes. So board
specific codes, such as lowlevel_init, can't has enough code. It make
a difficult to implement OneNAND IPL.
his patch make this common code as small as possible. and give
lowlevel_init can have more codes.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:24 +0000 (18:38 +0100)]
Add multi-chip NAND support for the TQM8548 modules
This patches configures the NAND UPM-FSL driver with multi-chip
support for the Micron MT29F8G08FAB NAND flash memory on the
TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:23 +0000 (18:38 +0100)]
Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:22 +0000 (18:38 +0100)]
Add support for TQM-specific chip select logic to FSL-UPM
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:21 +0000 (18:38 +0100)]
Add multi chip support to the FSL-UPM driver
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:20 +0000 (18:38 +0100)]
Enable multi chip support in the NAND layer
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:
Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Mike Frysinger [Sun, 12 Oct 2008 01:58:33 +0000 (21:58 -0400)]
Blackfin: put memory into self-refresh before/after programming clocks
When initializing the core clocks, stick external memory into self-refresh.
This gains us a few cool things:
- support suspend-to-RAM with Linux
- reprogram clocks automatically when doing "go" on u-boot.bin in RAM
- make sure settings are stable before flashing new version
- finally fully unify initialize startup code path between LDR/non-LDR
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 01:56:08 +0000 (21:56 -0400)]
Blackfin: do not program voltage regulator on parts that do not have one
Some newer Blackfins (like the BF51x) do not have an on-chip voltage
regulator, so do not attempt to program the memory as if it does.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 1 Jun 2008 05:28:24 +0000 (01:28 -0400)]
Blackfin: setup a sane default EBIU_SDBCTL for SDRAM controllers
If the board config does not specify an explicit EBIU_SDBCTL value, set it
up with sane values based on other configuration options.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 6 Dec 2008 23:06:58 +0000 (18:06 -0500)]
Blackfin: handle reboot anomaly 432
Workaround anomaly 432:
The bfrom_SysControl() firmware function does not clear the SIC_IWR1
register before executing the PLL programming sequence. Therefore, any
interrupt enabled in the SIC_IWR1 register prior to the call to
bfrom_SysControl() can prematurely terminate the idle sequence required
for the PLL to relock properly. SIC_IWR0 is properly handled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 18 Oct 2008 08:04:49 +0000 (04:04 -0400)]
Blackfin: kill off LDR jump block
The Boot ROM uses EVT1 as the entry point so set that rather than having
to use a tiny jump block in the default EVT1 location.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 6 Jan 2009 15:00:48 +0000 (10:00 -0500)]
Blackfin: simplify symbol_lookup() a bit
No need to skip a byte as the symbol table handles this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
projects / oweals / u-boot.git / log