wdenk [Sat, 30 Aug 2003 00:05:50 +0000 (00:05 +0000)]
Patch by Raghu Krishnaprasad, 7 Aug 2003:
add support for Adder II MPC852T module
wdenk [Fri, 29 Aug 2003 22:00:43 +0000 (22:00 +0000)]
* Patch by George G. Davis, 19 Aug 2003:
fix TI Innovator/OMAP1510 pin configs
* Patches by Kshitij, 18 Aug 2003
- add support for arm926ejs cpu core
- add support for TI OMAP 1610 Innovator Board
wdenk [Fri, 29 Aug 2003 20:57:53 +0000 (20:57 +0000)]
Patch by Yuli Barcohen, 14 Aug 2003:
add support for bzip2 uncompression
wdenk [Fri, 29 Aug 2003 10:05:53 +0000 (10:05 +0000)]
Add I2C and RTC support for RMU board using software I2C driver
(because of better response to iprobe command); fix problem with
"reset" command
stroese [Thu, 28 Aug 2003 14:24:37 +0000 (14:24 +0000)]
Patch from Matthias Fuchs.
stroese [Thu, 28 Aug 2003 14:17:32 +0000 (14:17 +0000)]
- Added CONFIG_BOOTP_DNS2 and CONFIG_BOOTP_SEND_HOSTNAME to CONFIG_BOOTP_MASK.
wdenk [Thu, 28 Aug 2003 09:41:22 +0000 (09:41 +0000)]
* Fix ICU862 environment problem
* Fix RAM size detection for RMU board
* Implement "reset" for MGT5100/MPC5200 systems
wdenk [Sun, 17 Aug 2003 18:55:18 +0000 (18:55 +0000)]
* Make Ethernet autonegotiation on INCA-IP work for all clock rates;
allow selection of clock frequency as "make" target
* Implement memory autosizing code for IceCube boards
* Configure network port on INCA-IP for autonegotiation
* Fix overflow problem in network timeout code
* Patch by Richard Woodruff, 8 Aug 2003:
Allow crc32 to be used at address 0x000 (crc32_no_comp, too).
wdenk [Thu, 7 Aug 2003 22:18:11 +0000 (22:18 +0000)]
Update for TQM board defaults:
disable clocks_in_mhz, enable boot count limit
dzu [Thu, 7 Aug 2003 15:04:48 +0000 (15:04 +0000)]
Removed tools/gdb from "make all" target. Added make target "gdbtools"
in toplevel directory instead. Removed astest.c from tools/gdb because
it is no longer relevant.
wdenk [Thu, 7 Aug 2003 14:52:18 +0000 (14:52 +0000)]
Disable debug print for normal use.
Fix MPC5200 FEC driver
dzu [Thu, 7 Aug 2003 14:22:10 +0000 (14:22 +0000)]
Removed the file tools/gdb/astest.c
dzu [Thu, 7 Aug 2003 14:20:31 +0000 (14:20 +0000)]
Removed tools/gdb from "make all" target. Added make target "gdbtools"
in toplevel directory instead. Removed astest.c from tools/gdb because
it is no longer relevant.
wdenk [Tue, 5 Aug 2003 18:22:44 +0000 (18:22 +0000)]
* Fix PCI support for MPC5200 / IceCube Board
wdenk [Tue, 5 Aug 2003 17:43:17 +0000 (17:43 +0000)]
* Map ISP1362 USB OTG controller for NSCU board
* Patch by Brad Parker, 02 Aug 2003:
fix sc520_cdp problems
* Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements)
* Allow erase command to cross flash bank boundaries
wdenk [Thu, 31 Jul 2003 22:56:30 +0000 (22:56 +0000)]
Must enable timebase earlier on MPC5200
wdenk [Sun, 27 Jul 2003 00:21:01 +0000 (00:21 +0000)]
* Patch by Scott McNutt, 21 Jul 2003:
Add support for LynuxWorks Kernel Downloadable Images (KDIs).
Both LynxOS and BlueCat linux KDIs are supported.
* Patch by Richard Woodruff, 25 Jul 2003:
use more reliable reset for OMAP/925T
* Patch by Nye Liu, 25 Jul 2003:
fix typo in mpc8xx.h
* Patch by Richard Woodruff, 24 Jul 2003:
Fixes for cmd_nand.c:
- Fixed null dereferece which could result in incorrect ECC values.
- Added support for devices with no Ready/Busy signal hooked up.
- Added OMAP1510 read/write protect handling.
- Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
for non-JFFS2.
- Switched default ECC to be JFFS2.
wdenk [Sat, 26 Jul 2003 08:08:08 +0000 (08:08 +0000)]
* Allow crc32 to be used at address 0x000
* Provide consistent interface to standalone applications to access
the 'global_data' structure
Provide a doc/README.standalone more useful to users/developers.
* Make IceCube MGT5100 FEC driver work
wdenk [Thu, 24 Jul 2003 23:38:38 +0000 (23:38 +0000)]
* Implement new mechanism to export U-Boot's functions to standalone
applications: instead of using (PPC-specific) system calls we now
use a jump table; please see doc/README.standalone for details
* Patch by Dave Westwood, 24 Jul 2003:
added support for Unity OS (a proprietary OS)
wdenk [Thu, 17 Jul 2003 23:16:40 +0000 (23:16 +0000)]
* Patch by Martin Krause, 17 Jul 2003:
add delay to get I2C working with "imm" command and s3c24x0_i2c.c
* Patch by Richard Woodruff, 17 July 03:
- Fixed bug in OMAP1510 baud rate divisor settings.
* Patch by Nye Liu, 16 July 2003:
MPC860FADS fixes:
- add MPC86xADS support (uses MPC86xADS.h)
- add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
o PLPRCR changes
o BRG changes (EXTAL/XTAL restricted to 10MHz)
o don't trust gclk() software measurement by default, depend on
CONFIG_8xx_GCLK_FREQ
- add DRAM SIMM not installed detection
- use more "correct" SDRAM initialization sequence
- allow different SDRAM sizes (8xxADS has 8M)
- default DER is 0
- remove unused MAMR defines from FADS860T.h (all done in fads.c)
- rename MAMR/MBMR defines to be more consistent. Should eventually
be merged into MxMR to better reflect the PowerQUICC datasheet.
* Patch by Yuli Barcohen, 16 Jul 2003:
support new Motorola PQ2FADS-ZU evaluation board which replaced
MPC8260ADS and MPC8266ADS
wdenk [Wed, 16 Jul 2003 21:53:01 +0000 (21:53 +0000)]
* Add support for IceCube board (with MGT5100 and MPC5200 CPUs)
* Add support for MGT5100 and MPC5200 processors
wdenk [Wed, 16 Jul 2003 16:40:22 +0000 (16:40 +0000)]
Incorporate Patch by Lutz Dennig, 15 Jul 2003.
wdenk [Tue, 15 Jul 2003 22:00:22 +0000 (22:00 +0000)]
Mode modem init support to F3+F4 key combination
wdenk [Tue, 15 Jul 2003 21:50:34 +0000 (21:50 +0000)]
Avoid unnecessary call to post_word_load();
make logbuf compile without POST
wdenk [Tue, 15 Jul 2003 21:08:26 +0000 (21:08 +0000)]
Adapt log driver to latest POST changes (POST_SLOWTEST)
wdenk [Tue, 15 Jul 2003 20:04:06 +0000 (20:04 +0000)]
Patches by Kshitij, 04 Jul 2003
- added support for arm925t cpu core
- added support for TI OMAP 1510 Innovator Board
wdenk [Tue, 15 Jul 2003 07:45:49 +0000 (07:45 +0000)]
* Patches by Martin Krause, 14 Jul 2003:
- add I2C support for s3c2400 systems (trab board)
- (re-) add "ping" to command table
* Fix handling of "slow" POST routines
wdenk [Mon, 14 Jul 2003 22:13:32 +0000 (22:13 +0000)]
* Patches by Yuli Barcohen, 13 Jul 2003:
- Correct flash and JFFS2 support for MPC8260ADS
- fix PVR values and clock generation for PowerQUICC II family
(8270/8275/8280)
* Patch by Bernhard Kuhn, 08 Jul 2003:
- add support for M68K targets
* Patch by Ken Chou, 3 Jul:
- Fix PCI config table for A3000
- Fix iobase for natsemi.c
(PCI_BASE_ADDRESS_0 is the IO base register for DP83815)
* Allow to enable "slow" POST routines by key press on power-on
* Fix temperature dependend switching of LCD backlight on LWMON
* Tweak output format for LWMON
stroese [Fri, 11 Jul 2003 08:23:12 +0000 (08:23 +0000)]
- Patch by Stefan Roese, 11 Jul 2003
stroese [Fri, 11 Jul 2003 08:20:33 +0000 (08:20 +0000)]
- Fixed interrupt polarity.
stroese [Fri, 11 Jul 2003 08:17:26 +0000 (08:17 +0000)]
- FPGA updated.
stroese [Fri, 11 Jul 2003 08:14:14 +0000 (08:14 +0000)]
- BSP command added.
stroese [Fri, 11 Jul 2003 08:13:25 +0000 (08:13 +0000)]
- AR405 config updated.
stroese [Fri, 11 Jul 2003 08:00:33 +0000 (08:00 +0000)]
- Fix bug in CONFIG_VERSION_VARIABLE.
wdenk [Mon, 7 Jul 2003 20:07:54 +0000 (20:07 +0000)]
* Add support for NSCU board
* Add support for TQM823M, TQM850M, TQM855M and TQM860M modules
* Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML
mirror bit flash on TQM8xxM modules
wdenk [Tue, 1 Jul 2003 21:06:45 +0000 (21:06 +0000)]
Patch by Kenneth Johansson, 30 Jun 2003:
get rid of MK_CMD_ENTRY macro; update doc/README.command
wdenk [Mon, 30 Jun 2003 16:24:52 +0000 (16:24 +0000)]
* Patch by Seb James, 30 Jun 2003:
Improve documentation of I2C configuration in README
* Fix problems with previous log buffer "fixes"
* Fix minor help text issues
* "log append" did not append a newline
wdenk [Sun, 29 Jun 2003 21:03:46 +0000 (21:03 +0000)]
Fix some missing commands, cleanup header files
(autoscript, bmp, bsp, fat, mmc, nand, portio, ...)
wdenk [Sat, 28 Jun 2003 23:18:28 +0000 (23:18 +0000)]
help text cleanup
wdenk [Sat, 28 Jun 2003 23:13:56 +0000 (23:13 +0000)]
Fix duplicate command entry.
wdenk [Sat, 28 Jun 2003 23:11:04 +0000 (23:11 +0000)]
Rewrite command lookup and help command (fix problems with bubble
sort when sorting command name list). Minor cleanup here and there.
wdenk [Sat, 28 Jun 2003 17:24:46 +0000 (17:24 +0000)]
Merge from "stable branch", tag LABEL_2003_06_28_1800-stable:
- Allow to call sysmon function interactively
- PIC on LWMON board needs delay after power-on
- Add missing RSR definitions for MPC8xx
- Improve log buffer handling: guarantee clean reset after power-on
- Add support for EXBITGEN board
- Add support for SL8245 board
wdenk [Fri, 27 Jun 2003 21:31:46 +0000 (21:31 +0000)]
* Code cleanup:
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
wdenk [Thu, 26 Jun 2003 22:04:09 +0000 (22:04 +0000)]
* Patches by Robert Schwebel, 26 Jun 2003:
- logdl
- csb226
- innokom
* Patch by Pantelis Antoniou, 25 Jun 2003:
update NetVia with V2 board support
wdenk [Wed, 25 Jun 2003 22:26:29 +0000 (22:26 +0000)]
* Header file cleanup for ARM
* Patch by Murray Jensen, 24 Jun 2003:
- make sure to use only U-boot provided header files
- fix problems with ".rodata.str1.4" section as used by GCC-3.x
stroese [Tue, 24 Jun 2003 14:32:24 +0000 (14:32 +0000)]
Patch from Stefan Roese.
stroese [Tue, 24 Jun 2003 14:31:16 +0000 (14:31 +0000)]
- Remove EEPROM command.
stroese [Tue, 24 Jun 2003 14:30:28 +0000 (14:30 +0000)]
- Add ping support.
stroese [Tue, 24 Jun 2003 14:27:27 +0000 (14:27 +0000)]
- Update NAND FLASH support.
stroese [Tue, 24 Jun 2003 14:26:41 +0000 (14:26 +0000)]
- Update new fpga file.
wdenk [Mon, 23 Jun 2003 18:12:28 +0000 (18:12 +0000)]
* Patch by Yuli Barcohen, 23 Jun 2003:
Update for MPC8260ADS board
* Patch by Murray Jensen, 23 Jun 2003:
- cleanup of GCC 3.x compiler warnings
wdenk [Sun, 22 Jun 2003 17:18:28 +0000 (17:18 +0000)]
* Patch by Rune Torgersen, 4 Jun 2003:
add large memory support for MPC8266ADS board
* Patch by Richard Woodruff, 19 June 03:
- Enabled standard u-boot device abstraction for ARM
- Enabled console device for ARM
- Initilized bi_baudrate for ARM
* Patch by Bill Hargen, 23 Apr 2003:
fix byte order for 824x I2C addresses (write op)
wdenk [Sun, 22 Jun 2003 10:30:54 +0000 (10:30 +0000)]
Had to move the RTC area for ATC board to upper addresses
(0xf5000000, to be specific). The reason is that the RTC first gets
accessed before MMU is initialized and, consequently, it needs to be
placed at physical addresses which are later mapped to the same
virtual addresses (like 0xf5000000 physical is mapped to 0xf5000000
virtual).
wdenk [Sat, 21 Jun 2003 00:17:24 +0000 (00:17 +0000)]
Patch by Murray Jensen, 20 Jun 2003:
- hymod update
- cleanup (especially for gcc-3.x compilers)
wdenk [Fri, 20 Jun 2003 23:10:58 +0000 (23:10 +0000)]
Patch by Tom Guilliams, 20 Jun 2003:
added CONFIG_750FX support for IBM 750FX processors
wdenk [Fri, 20 Jun 2003 22:36:30 +0000 (22:36 +0000)]
* Patch by Devin Crumb, 02 Apr 2003:
Fix clock divider rounding problem in drivers/serial.c
* Patch by Ken Chou, 19 June 2003:
Added support for A3000 SBC board (Artis Microsystems Inc.)
wdenk [Thu, 19 Jun 2003 23:58:30 +0000 (23:58 +0000)]
* Patch by Richard Woodruff, 19 June 03:
- Fixed smc91c111 driver to sync with the u-boot environment (driver/smc91c111.c).
- Added eth_init error return check in NetLoop (net/net.c).
wdenk [Thu, 19 Jun 2003 23:40:20 +0000 (23:40 +0000)]
Patches by Murray Jensen, 17 Jun 2003:
- Hymod board database mods: add "who" field and new xilinx chip types
- provide new "init_cmd_timeout()" function so code external to
"common/main.c" can use the "reset_cmd_timeout()" function before
entering the main loop
- add DTT support for adm1021 (new file dtt/adm1021.c; config
slightly different. see include/configs/hymod.h for an example
(requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
CFG_DTT_ADM1021 defined)
- add new "eeprom_probe()" function which has similar args and
behaves in a similar way to "eeprom_read()" etc.
- add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
- gdbtools copyright update
- ensure that set_msr() executes the "sync" and "isync" instructions
after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
- 8260 I/O ports fix: Open Drain should be set last when configuring
- add SIU IRQ defines for 8260
- allow LDSCRIPT override and OBJCFLAGS initialization: change to
config.mk to allow board configurations to override the GNU
linker script, selected via the LDSCRIPT, make variable, and to
give an initial value to the OBJCFLAGS make variable
- 8260 i2c enhancement:
o correctly extends the timeout depending on the size of all
queued messages for both transmit and receive
o will not continue with receive if transmit times out
o ensures that the error callback is done for all queued tx
and rx messages
o correctly detects both tx and rx timeouts, only delivers one to
the callback, and does not overwrite an earlier error
o logic in i2c_probe now correct
- add "vprintf()" function so that "panic()" function can be
technically correct
- many Hymod board changes
wdenk [Thu, 19 Jun 2003 23:04:19 +0000 (23:04 +0000)]
Patches by Robert Schwebel, 14 Jun 2003:
- add support for Logotronic DL datalogger board
- cleanup serial line after kermit binary download
- add debugX macro (debug level support)
- update mach-types.h to latest arm.linux.org.uk master list.
wdenk [Thu, 19 Jun 2003 23:01:32 +0000 (23:01 +0000)]
* Patches by David Müller, 12 Jun 2003:
- rewrite of the S3C24X0 register definitions stuff
- "driver" for the built-in S3C24X0 RTC
* Patches by Yuli Barcohen, 12 Jun 2003:
- Add MII support and Ethernet PHY initialization for MPC8260ADS board
- Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
configuration word supplied by FPGA on some MPC8260ADS boards
* Patch by Pantelis Antoniou, 10 Jun 2003:
Unify status LED interface
wdenk [Wed, 18 Jun 2003 20:22:24 +0000 (20:22 +0000)]
Add support for DS12887 RTC; add RTC support for ATC board
wdenk [Mon, 16 Jun 2003 23:50:08 +0000 (23:50 +0000)]
* Patch by Nicolas Lacressonniere, 11 Jun 2003:
Modifications for Atmel AT91RM9200DK ARM920T based development kit
- Add Atmel DataFlash support for reading and writing.
- Add possibility to boot a Linux from DataFlash with BOOTM command.
- Add Flash detection on Atmel AT91RM9200DK
(between Atmel AT49BV1614 and AT49BV1614A flashes)
- Replace old Ethernet PHY layer functions
- Change link address
* Patch by Frank Smith, 9 Jun 2003:
use CRIT_EXCEPTION for machine check on 4xx
* Patch by Detlev Zundel, 13 Jun 2003:
added implementation of the "carinfo" command in cmd_immap.c
wdenk [Sun, 15 Jun 2003 22:40:42 +0000 (22:40 +0000)]
* Fix CONFIG_NET_MULTI support in include/net.h
* Patches by Kyle Harris, 13 Mar 2003:
- Add FAT partition support
- Add command support for FAT
- Add command support for MMC
----
- Add Intel PXA support for video
- Add Intel PXA support for MMC
----
- Enable MMC and FAT for lubbock board
- Other misc changes for lubbock board
wdenk [Fri, 6 Jun 2003 11:20:01 +0000 (11:20 +0000)]
Patch by Robert Schwebel, April 02, 2003:
fix for SMSC91111 driver
stroese [Fri, 6 Jun 2003 09:44:40 +0000 (09:44 +0000)]
- Update new fpga file.
stroese [Fri, 6 Jun 2003 09:43:42 +0000 (09:43 +0000)]
- Fix compile bug (PPC4xx).
wdenk [Thu, 5 Jun 2003 19:37:36 +0000 (19:37 +0000)]
* Patch by Vladimir Gurevich, 04 Jun 2003:
make ppc405 ethernet driver compatible with CONFIG_NET_MULTI option
wdenk [Thu, 5 Jun 2003 19:27:42 +0000 (19:27 +0000)]
* Add support for RMU board
* Add support for TQM862L at 100/50 MHz
* Patch by Pantelis Antoniou, 02 Jun 2003:
major reconstruction of networking code;
add "ping" support (outgoing only!)
stroese [Thu, 5 Jun 2003 15:44:37 +0000 (15:44 +0000)]
Patch from Stefan Roese.
stroese [Thu, 5 Jun 2003 15:39:44 +0000 (15:39 +0000)]
- CFG_RX_ETH_BUFFER added.
stroese [Thu, 5 Jun 2003 15:38:29 +0000 (15:38 +0000)]
- CFG_ETH_RX_BUFFER added.
stroese [Thu, 5 Jun 2003 15:35:20 +0000 (15:35 +0000)]
- Fix bug for initial stack in data cache as pointed out by Thomas Schaefer (tschaefer@giga-stream.de). Now inital stack in data cache can be used even if the chip select is in use.
wdenk [Wed, 4 Jun 2003 15:05:30 +0000 (15:05 +0000)]
* Patch by Denis Peter, 04 June 2003:
add support for the MIP405T board
wdenk [Tue, 3 Jun 2003 23:54:09 +0000 (23:54 +0000)]
* Patches by Udi Finkelstein, 2 June 2003:
- Added support for custom keyboards, initialized by defining a
board-specific drv_keyboard_init as well as defining CONFIG_KEYBOARD .
- Added support for the RBC823 board.
- cpu/mpc8xx/lcd.c now automatically calculates the
Horizontal Pixel Count field.
* Fix alignment problem in BOOTP (dhcp_leasetime option)
[pointed out by Nicolas Lacressonnière, 2 Jun 2003]
* Patch by Mark Rakes, 14 May 2003:
add support for Intel e1000 gig cards.
* Patch by Nye Liu, 3 Jun 2003:
fix critical typo in MAMR definition (include/mpc8xx.h)
* Fix requirement to align U-Boot image on 16 kB boundaries on PPC.
* Patch by Klaus Heydeck, 2 Jun 2003
Minor changes for KUP4K configuration
wdenk [Sat, 31 May 2003 18:35:21 +0000 (18:35 +0000)]
* Patch by Marc Singer, 29 May 2003:
Fixed rarp boot method for IA32 and other little-endian CPUs.
* Patch by Marc Singer, 28 May 2003:
Added port I/O commands.
* Patch by Matthew McClintock, 28 May 2003
- cpu/mpc824x/start.S: fix relocation code when booting from RAM
- minor patches for utx8245
* Patch by Daniel Engström, 28 May 2003:
x86 update
* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
add nand flash support to SXNI855T configuration
fix/extend nand flash support:
- fix 'nand erase' command so does not erase bad blocks
- fix 'nand write' command so does not write to bad blocks
- fix nand_probe() so handles no flash detected properly
- add doc/README.nand
- add .jffs2 and .oob options to nand read/write
- add 'nand bad' command to list bad blocks
- add 'clean' option to 'nand erase' to write JFFS2 clean markers
- make NAND read/write faster
* Patch by Rune Torgersen, 23 May 2003:
Update for MPC8266ADS board
wdenk [Fri, 30 May 2003 12:48:29 +0000 (12:48 +0000)]
* Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
instead CFG_MONITOR_LEN is now only used to determine _at_compile_
_time_ (!) if the environment is embedded within the U-Boot image,
or in a separate flash sector.
* Cleanup CFG_DER #defines in config files (wd maintained only)
wdenk [Wed, 28 May 2003 08:06:31 +0000 (08:06 +0000)]
* Fix data abort exception handling for arm920t CPU
* Fix alignment problems with flash driver for TRAB board
* Patch by Donald White, 21 May 2003:
fix calculation of base address in pci_hose_config_device()
* Fix bug in command line parsing: "cmd1;cmd2" is supposed to always
execute "cmd2", even if "cmd1" fails. Note that this is different
to "run var1 var2" where the contents of "var2" will NOT be
executed when a command in "var1" fails.
wdenk [Fri, 23 May 2003 23:18:21 +0000 (23:18 +0000)]
Add zero-copy ramdisk support (requires corresponding kernel support!)
wdenk [Fri, 23 May 2003 12:36:20 +0000 (12:36 +0000)]
Patch by Kyle Harris, 20 May 2003:
In preparation for an ixp port, rename cpu/xscale and arch-xscale
into cpu/pxa and arch-pxa.
stroese [Fri, 23 May 2003 11:49:24 +0000 (11:49 +0000)]
Patch from Stefan Roese.
stroese [Fri, 23 May 2003 11:43:00 +0000 (11:43 +0000)]
- ASH405 board added (PPC405EP based).
- CPCI4052 added (PPC405GP based).
- CPCI405AB added (PPC405GP based).
- PCI405 added (PPC405GP based).
- PMC405 added (PPC405GP based).
stroese [Fri, 23 May 2003 11:41:44 +0000 (11:41 +0000)]
- ASH405 board added (PPC405EP based).
- BUBINGA405EP added (PPC405EP based).
- CPCI405AB added (PPC405GP based).
- PMC405 added (PPC405GP based).
stroese [Fri, 23 May 2003 11:39:05 +0000 (11:39 +0000)]
CONFIG_UART1_CONSOLE added.
wdenk [Fri, 23 May 2003 11:38:58 +0000 (11:38 +0000)]
Patch by Denis Peter, 19 Mai 2003:
add support for the MIP405-3 board
stroese [Fri, 23 May 2003 11:38:22 +0000 (11:38 +0000)]
DHCP support added.
stroese [Fri, 23 May 2003 11:35:47 +0000 (11:35 +0000)]
PMC405 board added.
stroese [Fri, 23 May 2003 11:35:09 +0000 (11:35 +0000)]
Code cleanup.
stroese [Fri, 23 May 2003 11:34:40 +0000 (11:34 +0000)]
New FPGA image with 527 support.
stroese [Fri, 23 May 2003 11:33:57 +0000 (11:33 +0000)]
Local Bus Timeout increased.
stroese [Fri, 23 May 2003 11:32:53 +0000 (11:32 +0000)]
Code reworked for PPC405EP support.
stroese [Fri, 23 May 2003 11:30:39 +0000 (11:30 +0000)]
CPCI405AB (special version of esd CPCI405) board added.
stroese [Fri, 23 May 2003 11:28:55 +0000 (11:28 +0000)]
BUBINGA405EP board added (IBM PPC405EP Eval Board).
stroese [Fri, 23 May 2003 11:27:18 +0000 (11:27 +0000)]
ASH405 board added (PPC405EP based).
stroese [Fri, 23 May 2003 11:25:57 +0000 (11:25 +0000)]
- PPC405EP support added.
- CONFIG_UART1_CONSOLE added (see README).
stroese [Fri, 23 May 2003 11:18:02 +0000 (11:18 +0000)]
PPC405EP support added.
stroese [Fri, 23 May 2003 11:16:49 +0000 (11:16 +0000)]
- PPC405EP support added.
- "nand_init" (NAND FLASH) added.
wdenk [Thu, 22 May 2003 22:52:13 +0000 (22:52 +0000)]
* Patch by Dave Ellis, 22 May 2003:
Fix problem with only partially cleared .bss segment
* Patch by Rune Torgersen, 12 May 2003:
get PCI to work on a MPC8266ADS board; incorporate change to
cpu/mpc8260/pci.c to enable overrides of PCI memory parameters
wdenk [Wed, 21 May 2003 20:26:20 +0000 (20:26 +0000)]
Add support for arbitrary bitmaps for TRAB's VFD command;
allow to pass boot bitmap addresses in environment variables;
allow for zero boot delay
wdenk [Tue, 20 May 2003 20:49:01 +0000 (20:49 +0000)]
* Add support for arbitrary bitmaps for TRAB's VFD command
* Patch by Christian Geißinger, 19 May 2002:
On TRAB: wait until the dummy byte has been completely sent
wdenk [Tue, 20 May 2003 14:25:27 +0000 (14:25 +0000)]
* Patch by David Updegraff, 22 Apr 2003:
update for CrayL1 board
* Patch by Pantelis Antoniou, 21 Apr 2003:
add boot support for ARTOS (a proprietary OS)
* Patch by Steven Scholz, 11 Apr 2003:
Add support for RTC DS1338
* Patch by Rod Boyce, 24 Jan 2003:
Fix counting of extended partitions in diskboot command
projects / oweals / u-boot.git / log