Michal Simek [Mon, 7 Oct 2019 08:33:23 +0000 (10:33 +0200)]
arm64: versal: Enable LIBFDT_OVERLAY
Enable device tree overlay to build all dtbs for Versal with -@ flag to
enable applying overlays.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 07:30:34 +0000 (09:30 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu100
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 12 Mar 2019 09:15:27 +0000 (10:15 +0100)]
arm64: zynqmp: Turn comment to gpio-line-names
Label gpio lines properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 08:20:07 +0000 (10:20 +0200)]
arm64: zynqmp: Add label property to all ina226 on zcu102
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 16 Aug 2019 08:42:42 +0000 (10:42 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu102
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Harini Katakam [Wed, 13 Mar 2019 14:11:19 +0000 (19:41 +0530)]
arm64: zynqmp: dt: Add optional gpio phy reset properties
Add gpio phy reset via I2C expander TCA6416 on board ZCU102.
A warning call trace is observer in probe when this reset is called
from context that can sleep. Keep this commented until that is
resolved in phylib.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Harini Katakam [Wed, 13 Feb 2019 11:32:21 +0000 (17:02 +0530)]
arm64: zynqmp: dt: Add missing DP83867 quirk
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 7 Mar 2019 07:15:52 +0000 (08:15 +0100)]
arm64: zynqmp: Enable fpd_dma for zcu104 platforms
Enable fpd_dma for these boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 07:40:23 +0000 (09:40 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu104
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 08:18:13 +0000 (10:18 +0200)]
arm64: zynqmp: Add label property to all ina226 on zcu106
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 07:46:36 +0000 (09:46 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu106
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Venkatesh Yadav Abbarapu [Thu, 5 Sep 2019 03:00:38 +0000 (08:30 +0530)]
arm64: zynqmp: Fix the si570 clock frequency on zcu111
The si570 clock frequency should be 156.25MHz as per datasheet.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 08:00:26 +0000 (10:00 +0200)]
arm64: zynqmp: Add label property to all ina226 on zcu111
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 07:45:03 +0000 (09:45 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu111
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Wed, 28 Aug 2019 09:30:57 +0000 (03:30 -0600)]
arm64: zynqmp: dt: Delete no-1-8-v property from zcu102-rev1.0
Currently zcu102 Rev1.0 board includes RevA sdhci dt node which has
no-1-8-v property. Since Rev1.0 has level shifters delete this
property to enable support for 1.8v.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 14 Oct 2019 08:35:03 +0000 (10:35 +0200)]
arm64: zynqmp: Remove fixme about memory size on zynqmp-p-a2197
System controller has 2GB of memory and fixme can be removed now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 25 Jun 2019 06:55:52 +0000 (08:55 +0200)]
arm64: zynqmp: Sync si570 setup and clock names
Setup proper si570 names and default factory setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 28 Jun 2019 11:52:09 +0000 (13:52 +0200)]
arm64: zynqmp: Fix m-a2197-01 DT based on latest schematics
Remove some FIXMEs and align it with latest schematics.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 7 Aug 2019 07:58:29 +0000 (09:58 +0200)]
arm64: zynqmp: Switch spi-flash to jedec,spi-nor on m-a2197
Mainline has done this switch and there is no reason not to switch it too.
Mainline U-Boot patch which has done that switch:
"dts: switch spi-flash to jedec, spi-nor compatible"
(sha1:
ffd4c7c2ecb745586239eb98d5dc0fe5e6ebe3bd)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 09:10:48 +0000 (11:10 +0200)]
arm64: zynqmp: Add label property to all ina226 on m-a2197-01
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 09:09:54 +0000 (11:09 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on m-a2197-01
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 14 Oct 2019 08:27:42 +0000 (10:27 +0200)]
arm64: zynqmp: Fix typo in zynqmp-p-a2197-00-revA
Trivial fix but not detected by checkpatch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nishant Mittal [Wed, 24 Jul 2019 09:28:52 +0000 (14:58 +0530)]
arm64: zynqmp: Added new tps53679 compatible string for a2197-0x boards
Added tps53679 compatible string to tps53681. They are both compatible to
each other and tps53679 has Linux driver already.
Signed-off-by: Nishant Mittal <nishant.mittal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nishant Mittal [Wed, 24 Jul 2019 09:28:52 +0000 (14:58 +0530)]
arm64: zynqmp: Fix i2c address of u70 on p-a2197-00 board
tps53681 is i2c address 0x60 not 0xc0.
Signed-off-by: Nishant Mittal <nishant.mittal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 09:10:36 +0000 (11:10 +0200)]
arm64: zynqmp: Add label property to all ina226 on g-a2197-00
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 26 Aug 2019 09:09:42 +0000 (11:09 +0200)]
arm64: zynqmp: Enable iio-hwmon for ina226 on g-a2197-00
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 8 Aug 2019 10:44:22 +0000 (12:44 +0200)]
arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 28 Jun 2019 11:16:10 +0000 (13:16 +0200)]
arm64: zynqmp: Sync names for SC with Versal
ZynqMP based System controller is present on Versal boards. This patch is
aligning names with Versal to follow the spec.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 14 Oct 2019 08:14:07 +0000 (10:14 +0200)]
ARM: zynq: Add missing pl353-smc node
DT binding was reviewed in Linux by commit
b0b41af12a1b
("dt-bindings: memory: Add pl353 smc controller devicetree binding
information") that's why this fragment can be also added to U-Boot
repository.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 14 Oct 2019 07:38:39 +0000 (09:38 +0200)]
ARM: zynq: Move BOOTM_NETBSD to Kconfig
The commit
4b0bcfa7c4ec ("Kconfig: Migrate CONFIG_BOOTM_* options")
moved BOOTM_ options to Kconfig that's why align zynq defconfig with it.
Disabling NETBSD was done by commit
d6f48ea5ce18
("ARM: zynq: Do not enable NETBSD support by default").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 14 Oct 2019 07:46:47 +0000 (09:46 +0200)]
arm64: versal: Enable GPIO command for Versal
Enable GPIO command for Xilinx Versal platform. Driver is updated that's
why it can be used directly. Driver is enabled by default through Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Shubhrajyoti Datta [Wed, 18 Sep 2019 06:40:31 +0000 (12:10 +0530)]
gpio: zynq: Add gpio driver support for PMC gpio
This patch adds support for gpio driver for pmc gpio.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ashok Reddy Soma [Mon, 16 Sep 2019 09:35:16 +0000 (03:35 -0600)]
gpio: zynq: Add gpio driver support for Versal
This patch adds support for gpio driver for versal platform
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 10 Oct 2019 09:26:16 +0000 (11:26 +0200)]
firmware: zynqmp: Clean up zynqmp_power_probe
Fix error debug messages to be more accurate and aligned with debug message
style in the whole file.
And do not initialize ret variable because it is initialized later on and
it is just additional step.
Fixes:
1327d1678bd2 ("firmware: zynqmp: Add zynqmp-power support")
Reported-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Michal Simek [Thu, 10 Oct 2019 09:09:15 +0000 (11:09 +0200)]
firmware: zynqmp: Report error when xilinx_pm_request called from EL3
Function should report error when called in EL3 context. Also report it as
error instead 0 (success).
Reported-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Michal Simek [Fri, 4 Oct 2019 13:35:45 +0000 (15:35 +0200)]
arm64: zynqmp: Convert invoke_smc() to xilinx_pm_request()
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 4 Oct 2019 13:52:43 +0000 (15:52 +0200)]
arm64: versal: Rename versal_pm_request to xilinx_pm_request
Use generic name instead of Versal specific because this should be also
used on ZynqMP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 4 Oct 2019 13:45:29 +0000 (15:45 +0200)]
arm64: xilinx: Move firmware functions from platform to driver
versal_pm_request() and invoke_smc() are almost the same. Only one
difference is that versal_pm_request is adding PM_SIP_SVC offset to api_id.
The patch is moving platform implementation to firmware driver code for
synchronization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Michal Simek [Fri, 4 Oct 2019 13:25:18 +0000 (15:25 +0200)]
arm64: versal: Clean pm_api_id usage
Copy enum values from platform code to firmware code. IDs are shared
between ZynqMP and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 23 Oct 2019 18:04:02 +0000 (14:04 -0400)]
Merge tag 'u-boot-stm32-2019-10-23' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Disable CONFIG_NET flag for MCU STM32
- Fix ramdisk_addr_r for stm32f746-disco
- Fix USB product id for stm32mp1
Tom Rini [Wed, 23 Oct 2019 11:55:20 +0000 (07:55 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- Add LS1027A, LS1018A, LS1017A support
- Few updates related to usb, ls1012a, lx2160a
Patrick Delaunay [Fri, 13 Sep 2019 13:24:17 +0000 (15:24 +0200)]
board: stm32mp1: fixup the usb product id for USB download gadget
Select the correct USB product id used by the download gadget
for ST stm32mp1 boards.
The board stm32mp1 select the correct product id, as defined in
http://www.linux-usb.org/usb.ids for the STMicroelectronics
vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM):
- dfu = 0xdf11 : STM Device in DFU mode
it is the value used by ROM code and reused for stm32prog
command
- fasboot = 0x0afb : Android Fastboot device
- others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM)
Mass Storage Device
it is used for UMS command / usb_dnl_ums
This patch avoid conflict when the same USB VID/PID is used for
ums, fastboot or dfu command (two different protocols associated
to the same PID).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Mon, 16 Sep 2019 08:56:51 +0000 (10:56 +0200)]
configs: stm32f746-disco: Fix ramdisk_addr_r
Set ramdisk_addr_r to 0xC0600000.
Reported-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:45 +0000 (10:09 +0200)]
configs: stm32h743-eval: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:44 +0000 (10:09 +0200)]
configs: stm32h743-disco: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:43 +0000 (10:09 +0200)]
configs: stm32f469-discovery: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:42 +0000 (10:09 +0200)]
configs: stm32f429-evaluation: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:41 +0000 (10:09 +0200)]
configs: stm32f429-discovery: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Mon, 21 Oct 2019 13:02:40 +0000 (15:02 +0200)]
dm: pinctrl: fix for introduce PINCONF_RECURSIVE option
Correct the name of the define used CONFIG_IS_ENABLED which is
not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE.
The recursive calls is conditional only for UCLASS_PINCONFIG
"pinconfig" driver.
It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL
"pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to
be removed for this driver.
This correct a regression introduced because the same patch is
applied twice times in u-boot-dm branch:
- commit
e878b53a79d1 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit
c20851b3d850 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Mon, 21 Oct 2019 13:07:54 +0000 (15:07 +0200)]
pinctrl: Kconfig: remove duplicated nodes
Remove the duplicated configs introduced when the same patch is
applied twice times:
- commit
e878b53a79d1 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit
c20851b3d850 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Biwen Li [Mon, 21 Oct 2019 06:53:30 +0000 (12:23 +0530)]
armv7: ls102xa: Don't power down OCRAM1 during deep sleep
To allow OCRAM to be used as wakeup source in
deep sleep, do not power it down.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Wed, 25 Sep 2019 10:40:42 +0000 (18:40 +0800)]
armv7: ls102xa: add errata ID A-008646 for workaround
The patch adds an errata ID A-008646 for workaround
to provide more information by errata ID.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Wasim Khan [Tue, 15 Oct 2019 08:54:11 +0000 (08:54 +0000)]
armv8: Update LX2160A/LX2120A/LX2080A SVR value
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Yuantian Tang [Thu, 10 Oct 2019 09:19:37 +0000 (17:19 +0800)]
armv8: ls1028a: disable multimedia for ls1027a, ls1017a
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Udit Agarwal [Mon, 30 Sep 2019 10:16:57 +0000 (10:16 +0000)]
board/ls1028a: Add call to sec_init()
Adds sec_init call to initialise the job ring parameters
for secure boot operations.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Mon, 30 Sep 2019 07:08:34 +0000 (12:38 +0530)]
configs: ls1012afrwy: Add CONFIG_ENV_ADDR
This configuration enables picking the environment from flash before
DDR init.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Wed, 25 Sep 2019 09:48:11 +0000 (17:48 +0800)]
armv7: ls102xa: Correct endianness of SCFG_SPARECR8 read
The patch corrects endianness of register SCFG_SPARECR8 read
in_le32 -> in_be32
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Ran Wang [Fri, 20 Sep 2019 09:34:29 +0000 (17:34 +0800)]
armv8: fsl-layerscape: Make USB masters snoopable
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Wed, 18 Sep 2019 10:58:04 +0000 (16:28 +0530)]
armv7: ls102xa: Update SCFG_QSPI_CLKSEL value
Update SCFG_QSPI_CLKSEL value : 0xC -> 0x5
which means ClusterPLL/16
Signed-off-by: Ashish Kumar <Ashish.kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Wed, 18 Sep 2019 09:28:11 +0000 (14:58 +0530)]
configs: ls1012ardb: Add CONFIG_ENV_ADDR
CONFIG_ENV_ADDR config option enables picking the environment from
flash before DDR init.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Yuantian Tang [Wed, 18 Sep 2019 08:50:52 +0000 (16:50 +0800)]
armv8: ls1028a: Add more personalities support
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Anatolij Gustschin [Fri, 18 Oct 2019 19:38:33 +0000 (21:38 +0200)]
spl: mmc: make eMMC HW boot partition configuration optional
Loading U-Boot on i.MX8QXP MEK board is broken since recent changes
in spl_mmc:
U-Boot SPL
2019.10-00162-gff5bd397e4 (Oct 18 2019 - 15:50:45 +0200)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
Load image from MMC/SD 0x46400
spl: mmc partition switch failed
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The newly added CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION option
is selected automatically and overrides the EXT_CSC_PART_CONFIG
configurations with default value, always selecting the eMMC boot
partition 1. Boards which place U-Boot image in other partitions
became not bootable.
Fix this by making the eMMC HW boot partition selection optional.
Fixes:
17241ea0543a (spl: mmc: Add option to set eMMC HW boot partition)
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tom Rini [Fri, 18 Oct 2019 20:37:03 +0000 (16:37 -0400)]
Merge tag 'efi-2020-01-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1 (2)
Install the simple file protocol only if there is a file system on the
partition.
Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
Tom Rini [Fri, 18 Oct 2019 20:36:44 +0000 (16:36 -0400)]
Merge tag 'u-boot-amlogic-
20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Tom Rini [Fri, 18 Oct 2019 20:36:16 +0000 (16:36 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Support sifive DM based gpio driver for FU540-SoC.
- Align boot image header with Linux v5.3
Guillaume La Roque [Fri, 11 Oct 2019 15:33:58 +0000 (17:33 +0200)]
configs: sei610: Add config file to fix userdata size
Add separate config file to handle the different eMMC size on
the sei610 board.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Guillaume La Roque [Fri, 11 Oct 2019 15:33:57 +0000 (17:33 +0200)]
configs: sei510: rework header and fix userdata size
Move android generic config and boot sequence in meson64_android header
and fix size of userdata to use all eMMC on SEI510.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:56 +0000 (17:33 +0200)]
boards: amlogic: add SEI610 support
Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
- Amlogic S905X3 ARM Cortex-A55 quad-core SoC
- 2GB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- 1 x USB Type-C DRD
- 1 x FTDI USB Serial Debug Interface
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:55 +0000 (17:33 +0200)]
ARM: dts: meson-sm1: add U-Boot specific DT for graphics
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 13:12:20 +0000 (15:12 +0200)]
configs: sei510: enable everything-else power domain
The GX VPU Power Domain driver has been replaced by the Everything-Else
Power Domain driver for G12A and SM1.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 13:12:19 +0000 (15:12 +0200)]
power: domain: add Amlogic Everything-Else power domain driver
Based on the
54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain
driver for Amlogic SoCs.
This driver handles the VPU Power domain and other domains from the
Everything-Else part of the SM1 and G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:54 +0000 (17:33 +0200)]
ARM: dts: Import SEI610 DT from Linux 5.4-rc2
Import the Amlogic SM1 DT and the SEI610 board DT from [1]
[1]
da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:53 +0000 (17:33 +0200)]
clk: meson-sm1: add compatible
The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:52 +0000 (17:33 +0200)]
mmc: meson-gx: add support for mmc-pwrseq-emmc
Add support for mmc-pwrseq-emmc in the meson-gx mmc driver to support
enabling the eMMC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:51 +0000 (17:33 +0200)]
ARM: meson: add SM1 SoC id
Add the missing IDs to detect the SM1 S905X3 SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:57 +0000 (16:03 +0200)]
arm: meson: Recognize A311D SoC
Values imported from Linux driver, but in correct numeric order.
Khadas VIM3 prints: Amlogic Meson G12B (A311D) Revision 29:b (10:2)
Cc: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:56 +0000 (16:03 +0200)]
arm: meson: Tidy SoC information output
Write SoC instead of Soc. The Linux driver is not affected.
Fixes:
f41d723b9f ("ARM: meson: display Amlogic SoC Information")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:55 +0000 (16:03 +0200)]
configs: Add Khadas VIM3 defconfig
Derived from odroid-n2_defconfig and README.odroid-n2.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:54 +0000 (16:03 +0200)]
arm: dts: Import and update DT for Khadas VIM3
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from
da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 30 Aug 2019 12:09:28 +0000 (14:09 +0200)]
configs: sei510: enable Video Display support
Add the necessary config options to support BMP display over HDMI,
and add a preboot command to load the BMP file from a predefined
eMMC partition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:27 +0000 (14:09 +0200)]
ARM: dts: meson-g12a: add U-Boot specific DT for graphics
Like the meson-gx support, add the U-Boot specific bits in DT
to support graphics on G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:26 +0000 (14:09 +0200)]
arm: meson: board-g12a: Setup VPU in fdt
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:25 +0000 (14:09 +0200)]
video: meson: add compatible for Amlogic G12A
Finally add the Amlogic G12A SoC compatible for the VPU driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:24 +0000 (14:09 +0200)]
video: meson: sync with linux drm-misc tree
Synchronize the Amlogic Meson Video driver back with the latest
DRM misc tree, adding G12A platform support, from the latest commit:
528a25d040bc ("drm: meson: use match data to detect vpu compatibility")
The sync includes the following changes from Linux adapted to U-Boot:
- Add support for VIC alternate timings
- Switch PLL to 5.94GHz base for 297Mhz pixel clock
- Add registers for G12A SoC
- Add G12A Support for VPP setup
- Add G12A Support for VIU setup
- Add G12A support for OSD1 Plane
- Add G12A support for plane handling in CRTC driver
- Add G12A support for CVBS Encoder
- Add G12A Video Clock setup
- Add G12A support for the DW-HDMI Glue
- fix G12A HDMI PLL settings for 4K60 1000/1001 variations
- fix primary plane disabling
- fix G12A primary plane disabling
- mask value when writing bits relaxed
- crtc: drv: vpp: viu: venc: use proper macros instead of magic constants
- global clean-up
- add macro used to enable HDMI PLL
- venc: set the correct macrovision max amplitude value
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:23 +0000 (14:09 +0200)]
video: meson: remove power domain get
Remove getting and enabling the node power domain since it's now handled
by the dm core directly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:22 +0000 (14:09 +0200)]
clk: meson: g12a: add support for VPU/HDMI clocks
Add necessary clock support to set up clock for the VPU and
HDMI support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:21 +0000 (14:09 +0200)]
power: domain: meson-gx-pwrc: add G12A support
Add Amlogic G12A support for the gx-pwrc driver, aligned on the
Linux v5.2 driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Daniel Drake [Tue, 6 Aug 2019 08:10:42 +0000 (16:10 +0800)]
board: amlogic: document alternative libretech-cc installation methods
As already documented in this README, several binaries must be
glued together in order to boot the device.
Extend the documentation to cover the prebuilt binaries
(saving you the hassle of installing ancient cross-compilers),
and also mention the open source replacements for the encryption
tool (which is especially useful if you want to avoid requiring
32-bit x86 binaries in your build system).
Signed-off-by: Daniel Drake <drake@endlessm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Atish Patra [Wed, 9 Oct 2019 17:34:17 +0000 (10:34 -0700)]
RISC-V: Align boot image header with Linux
The released Linux boot image header in v5.3 is different from the
one present in U-Boot. Align the header with the new version. The
changes in Linux are backward compatible. Previous U-Boot releases
with older header will continue to work as well. As v5.3 kernel is
the first one to support image header, there is no compatibility
issue between new U-Boot (with this patch) and older kernel.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Sagar Shrikant Kadam [Tue, 1 Oct 2019 17:00:47 +0000 (10:00 -0700)]
configs: fu540: enable gpio driver
Enable the DM based GPIO driver for FU540-C000 SoC.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Sagar Shrikant Kadam [Tue, 1 Oct 2019 17:00:46 +0000 (10:00 -0700)]
gpio: sifive: add support for DM based gpio driver for FU540-SoC
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Sun, 13 Oct 2019 09:54:20 +0000 (11:54 +0200)]
efi_loader: enable CONFIG_CMD_NVEDIT_EFI on QEMU
To reduce the default image size CONFIG_CMD_NVEDIT_EFI was disabled by
default. Re-enable it on the QEMU platforms supporting the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:38 +0000 (14:59 +0900)]
efi_loader: disk: install FILE_SYSTEM_PROTOCOL only if available
In the current implementation, EFI_SIMPLEFILE_SYSTEM_PROTOCOL is always
installed to all the partitions even if some of them may house no file
system.
With this patch, that protocol will be installed only if any file system
exists.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:37 +0000 (14:59 +0900)]
fs: add fs_get_type() for current filesystem type
This function is a variant of fs_get_type_name() and returns a filesystem
type with which the current device is associated.
We don't want to export fs_type variable directly because we have to take
care of it consistently within fs.c.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:36 +0000 (14:59 +0900)]
fs: clean up around fs_type
fs_ls(), fs_mkdir() and fs_unlink() sets fs_type to FS_TYPE_ANY
explicitly, but it is redundant as they call fs_close().
So just remove those lines.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 13 Oct 2019 08:26:26 +0000 (10:26 +0200)]
fs: update fs_close() description
Provide a more detailed description of fs_close().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:35 +0000 (14:59 +0900)]
fs: export fs_close()
fs_close() closes the connection to a file system which opened with
either fs_set_blk_dev() or fs_set_dev_with_part(). Many file system
functions implicitly call fs_close(), e.g. fs_closedir(), fs_exist(),
fs_ln(), fs_ls(), fs_mkdir(), fs_read(), fs_size(), fs_write()
and fs_unlink().
So just export it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Wed, 9 Oct 2019 07:19:52 +0000 (16:19 +0900)]
efi_loader: device_path: check against file path length
device_path strcuture has 2 bytes of "length" field, and so
file path length should not exceed this limit, 65535.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Thu, 17 Oct 2019 11:26:16 +0000 (07:26 -0400)]
Merge tag 'for-v2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-ubi
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
Tom Rini [Wed, 16 Oct 2019 22:10:31 +0000 (18:10 -0400)]
Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement