Wolfgang Denk [Sat, 7 Feb 2009 21:53:45 +0000 (22:53 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Sat, 7 Feb 2009 21:17:44 +0000 (22:17 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash
Wolfgang Denk [Sat, 7 Feb 2009 21:17:19 +0000 (22:17 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Sat, 7 Feb 2009 21:08:53 +0000 (22:08 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Dirk Eibach [Tue, 3 Feb 2009 14:15:21 +0000 (15:15 +0100)]
ppc4xx: Make PCIE support selectable
On some platforms PCIE support is not required, but would be included
because the cpu supports it. To reduce fooprint it is now configurable
via CONFIG_PCI_DISABLE_PCIE.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 3 Feb 2009 21:13:16 +0000 (22:13 +0100)]
ppc4xx: Only fixup opb attached UARTs
This patch updates the fdt UART clock fixup code to
only touch CPU internal UARTs on 4xx systems.
Only these UARTs are definitely clocked by gd->uart_clk.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Mike Frysinger [Tue, 13 Jan 2009 16:00:29 +0000 (11:00 -0500)]
Blackfin: move default boot SPI CS to common code
Move the default SPI CS that we boot from into common code so that it can
be used in other SPI drivers and environment settings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 10 Dec 2008 17:33:54 +0000 (12:33 -0500)]
Blackfin: dynamically update UART speed when initializing
Previously, booting over the UART required the baud rate to be known ahead
of time. Using a bit of tricky simple math, we can calculate the new board
rate based on the old divisors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Mike Frysinger [Tue, 9 Dec 2008 22:21:08 +0000 (17:21 -0500)]
Blackfin: add support for fast SPI reads with Boot ROM
Newer Blackfin boot roms support using the fast SPI read command rather than
just the slow one. If the functionality is available, then use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 01:46:52 +0000 (21:46 -0400)]
Blackfin: check for reserved settings in DDR MMRs
Some bits of the DDR MMRs should not be set. If they do, bad things may
happen (like random failures or hardware destruction).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 01:54:00 +0000 (21:54 -0400)]
Blackfin: set default voltage levels for BF538/BF539 parts
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 1 Jun 2008 05:29:57 +0000 (01:29 -0400)]
Blackfin: use on-chip syscontrol() rom function when available
Newer Blackfin's have an on-chip rom with a syscontrol() function that needs
to be used to properly program the memory and voltage settings as it will
include (possibly critical) factory tested bias values.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Stefan Roese [Thu, 5 Feb 2009 10:44:52 +0000 (11:44 +0100)]
cfi_flash: Fix typo in cfi_flash.c
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small typo and compilation warning for systems with CFI
legacy support (e.g. hcu4). This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 29 Jan 2009 10:21:38 +0000 (11:21 +0100)]
jedec_flash: Only use manufacturer defines from common flash.h
This patch removes the double defined manufacturer defines from
jedec_flash.c. Since the common defines in flash.h are 32bit
we now need the (16) cast. This patch also removes the compilation
warning (e.g. seen on hcu5):
./MAKEALL hcu5
Configuring for hcu5 board...
jedec_flash.c:219: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 5 Feb 2009 10:25:57 +0000 (11:25 +0100)]
cfi_flash: Silence compilation warning
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small compilation warning. This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
Becky Bruce [Mon, 2 Feb 2009 22:34:51 +0000 (16:34 -0600)]
flash/cfi_flash: Use virtual sector start address, not phys
include/flash.h was commented to say that the address in
flash_info->start was a physical address. However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address. So I corrected the
comment to indicate that this was a virtual address.
The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver. However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places. I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls. The code is now consistent.
The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Mike Frysinger [Mon, 6 Oct 2008 07:45:55 +0000 (03:45 -0400)]
Blackfin: update anomaly lists
Update the anomaly lists to match latest anomaly sheets.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Ralph Kondziella [Mon, 26 Jan 2009 19:34:36 +0000 (12:34 -0700)]
ADS5121 Add PATA support
Original patch from Ralph Kondziella
plus clean up by Wolfgang Denk
plus changes by John Rigby
use ips clock not lpc
port forward to current u-boot release
Signed-off-by: Ralph Kondziella <rk@argos-messtechnik.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: John Rigby <jrigby@freescale.com>
Martha Marx [Mon, 26 Jan 2009 17:45:07 +0000 (10:45 -0700)]
ADS5121 Add IC Ident Module (IIM) support
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
Wolfgang Denk [Tue, 3 Feb 2009 22:16:15 +0000 (23:16 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
John Rigby [Fri, 23 Jan 2009 17:33:15 +0000 (10:33 -0700)]
ADS5121 Fix rev2 silicon pci iopad config
Reset config is not correct
Signed-off-by: John Rigby <jrigby@freescale.com>
John Rigby [Wed, 19 Nov 2008 20:57:34 +0000 (13:57 -0700)]
ADS5121 DIU Add diu_bmp_addr env
Add support for using a bmp other than
FSL_Logo_BMP for the DIU splash screen.
Can now set the env var "diu_bmp_addr" to
the address of a BMP in flash to use instead
of the default FSL_Logo_BMP.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
John Rigby [Thu, 30 Oct 2008 22:39:35 +0000 (16:39 -0600)]
ADS5121 DIU Make inclusion of FSL logo optional
Make inclusion of FSL logo optional and
turn it off by default.
Signed-off-by: John Rigby <jrigby@freescale.com>
Remy Bohmer [Sun, 1 Feb 2009 11:27:53 +0000 (12:27 +0100)]
Compile warning fix in onenand_uboot.h
Regression since merge window after 2009.01
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Thu, 29 Jan 2009 05:33:55 +0000 (06:33 +0100)]
USB: Add EHCI support for VCT EHCI controller (really with driver now)
Somehow I missed the real driver part in my last patch version. This patch
now adds the driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Cliff Cai [Sat, 29 Nov 2008 23:22:38 +0000 (18:22 -0500)]
Blackfin: add driver for on-chip MMC/SD controller
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 02:47:34 +0000 (22:47 -0400)]
Blackfin: add port muxing for BF51x SPI
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 6 Jan 2009 11:16:19 +0000 (06:16 -0500)]
Blackfin: output booting source when booting
Knowing the booting source of the part is useful, especially when the part
can switch dynamically between sources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 11 Dec 2008 11:30:46 +0000 (06:30 -0500)]
Blackfin: set default CONFIG_ENV_SPI_CS based on bootrom
Set the default CONFIG_ENV_SPI_CS value to match the SPI CS that is used by
the Blackfin on-chip bootrom to boot out of SPI flash.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 11 Dec 2008 09:06:26 +0000 (04:06 -0500)]
Blackfin: update asm-blackfin/posix_types.h to latest Linux version
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 6 Dec 2008 07:54:52 +0000 (02:54 -0500)]
Blackfin: add port I bits
Some people need to access port I, so make sure the pins are defined.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Thu, 27 Nov 2008 03:16:45 +0000 (22:16 -0500)]
Blackfin: add driver for on-chip ATAPI controller
This is a port of the Linux Blackfin on-chip ATAPI driver to U-Boot.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 27 Nov 2008 02:43:06 +0000 (21:43 -0500)]
Blackfin: add driver for on-chip NAND controller
This is a port of the Linux Blackfin on-chip NFC driver to U-Boot.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 12 Nov 2008 12:18:15 +0000 (07:18 -0500)]
Blackfin: build with -mno-fdpic
Use the -mno-fdpic flag so that any Blackfin toolchain can be used to build
up u-boot, including ones that output FDPIC ELF by default.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 11 Nov 2008 10:43:57 +0000 (05:43 -0500)]
Blackfin: fix up EBIU defines
The EBIU defines for EBSZ 256/512 were incorrect.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 5 Nov 2008 17:45:24 +0000 (12:45 -0500)]
Blackfin: use 8/16/32 bit transfer widths in dma_memcpy()
Rather than using 8bit transfers for everything, use 8/16/32 bit transfers
as usable with the source/destination addresses and the count size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 5 Nov 2008 13:50:23 +0000 (08:50 -0500)]
Blackfin: only flag L1 instruction for DMA memcpy
The performance difference from doing an 8 bit DMA memcpy vs an optimized
core memcpy can be pretty big when you add in the overhead of setting up the
MDMA registers, cache flushes, etc... So only use dma_memcpy() when we
actually require it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 5 Nov 2008 12:20:37 +0000 (07:20 -0500)]
Blackfin: dma_memcpy(): fix random failures
We have to make sure the DMA channel is actually disabled in hardware before
attempting to reprogram it. Otherwise the new settings are ignored and we
end up with random hangs/failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 4 Nov 2008 05:04:03 +0000 (00:04 -0500)]
Blackfin: rewrite cache handling functions
Take the cache flush functions from the kernel as they use hardware loops in
order to get optimal performance.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 4 Nov 2008 03:30:05 +0000 (22:30 -0500)]
Blackfin: setup bi_enetaddr for single nets
For systems with CONFIG_NET_MULTI disabled, bi_enetaddr does not get setup
based on $ethaddr, so set it up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 25 Oct 2008 02:48:47 +0000 (22:48 -0400)]
Blackfin: cache core/system clock values
Calculating the clocks requires a bit of calls to gcc math functions, so
cache the values after the first run since they'll most likely never
change once U-Boot is up and running.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 24 Oct 2008 22:18:16 +0000 (18:18 -0400)]
Blackfin: enable --gc-sections
Start building all Blackfin boards with -ffunction-sections/-fdata-sections
and linking with --gc-sections.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 21 Oct 2008 01:08:54 +0000 (21:08 -0400)]
Blackfin: dont check baud if it wont actually get used
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 14 Oct 2008 11:54:09 +0000 (07:54 -0400)]
Blackfin: add driver for on-chip SPI controller
This fills out the SPI backend for the Blackfin on-chip SPI peripheral.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 18 Oct 2008 09:33:51 +0000 (05:33 -0400)]
Blackfin: only build post code when CONFIG_POST
Save some time by using CONFIG_POST in the Makefile rather than C files.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 8 Jan 2009 16:57:57 +0000 (11:57 -0500)]
Blackfin: bfin_mac: cleanup pointer/casts for aliasing issues
Redo how pointers are managed to get rid of ugly casts and strict pointer
aliasing issues that are highlighted by gcc 4.3.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Tue, 9 Dec 2008 22:46:21 +0000 (17:46 -0500)]
Blackfin: bfin_mac: convert CONFIG_BFIN_MAC_RMII to CONFIG_RMII
No point in having a Blackfin-specific define "CONFIG_BFIN_MAC_RMII" that
does exactly the same thing as common "CONFIG_RMII".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Wed, 5 Nov 2008 11:36:15 +0000 (06:36 -0500)]
Blackfin: bfin_mac: use common debug()
Rather then defining our own DEBUGF(), just use the common debug().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Mon, 20 Oct 2008 17:59:51 +0000 (13:59 -0400)]
Blackfin: bfin_mac: respect CONFIG_PHY_{ADDR,CLOCK_FREQ}
Rather than having the on-chip MAC hardcoded to phy address 1 and a speed
of 2.5mhz, use these as defaults if the board doesn't specify otherwise.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Tue, 14 Oct 2008 08:52:00 +0000 (04:52 -0400)]
Blackfin: bfin_mac: cleanup MII/PHY functions
Cleanup and rewrite the MII/PHY related functions so that we can reuse the
existing common linux/miiphy.h code and hook into the `mii` command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Tue, 14 Oct 2008 04:31:30 +0000 (00:31 -0400)]
Blackfin: bfin_mac: set MDCDIV based on SCLK
Rather than hardcoding MDCDIV to 24 (which is correct for ~125mhz SCLK),
use the real algorithm so it gets set correctly regardless of SCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Wolfgang Denk [Sun, 1 Feb 2009 20:38:07 +0000 (21:38 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Sun, 1 Feb 2009 20:31:37 +0000 (21:31 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Wolfgang Denk [Sun, 1 Feb 2009 20:24:38 +0000 (21:24 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-ixp
Jean-Christophe PLAGNIOL-VILLARD [Sat, 31 Jan 2009 08:10:48 +0000 (09:10 +0100)]
ixp: move serial to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 31 Jan 2009 08:04:58 +0000 (09:04 +0100)]
ixp: move pci init in arm/board instead of cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 31 Jan 2009 07:56:49 +0000 (08:56 +0100)]
ixp: move pci drivers to drivers/pci
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 31 Jan 2009 07:53:44 +0000 (08:53 +0100)]
ixp: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 31 Jan 2009 07:53:44 +0000 (08:53 +0100)]
ixp: add missing os define
need by arm-elf toolchains and no impact on the arm-linux one
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 31 Jan 2009 08:53:39 +0000 (09:53 +0100)]
ixp: remove the option to include the Microcode
instead the board will have to load it from flash or ram
which will be specified by npe_ucode env var
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 30 Jan 2009 08:45:23 +0000 (09:45 +0100)]
ixp/npe: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 28 Jan 2009 20:58:04 +0000 (21:58 +0100)]
SX1: add hardware V2 support
In the V2 the 2 flash has been replace by one 32MB flash
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 28 Jan 2009 20:58:03 +0000 (21:58 +0100)]
SX1: Fix second flash mapping
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 28 Jan 2009 20:58:03 +0000 (21:58 +0100)]
SX1: add CONFIG_STDOUT_USBTTY to enable preboot stdout redirect to usbtty
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 28 Jan 2009 20:57:59 +0000 (21:57 +0100)]
move Samsung's board to board/samsung
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 29 Jan 2009 11:07:21 +0000 (12:07 +0100)]
move ARM Ltd. to vendor dir
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Larry Johnson [Wed, 28 Jan 2009 20:30:37 +0000 (15:30 -0500)]
ppc4xx: Clean up configuration file for Korat board
This patch updates the default environmental variables for the
Korat PPC 440EPx board, and makes additional minor fixes.
Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Larry Johnson [Wed, 28 Jan 2009 20:30:02 +0000 (15:30 -0500)]
ppc4xx: Add variable "korat_usbcf" for Korat board
The new environment variable "korat_usbcf" selects the USB
port used by the Korat board's CompactFlash controller.
Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Gunnar Rangoy [Fri, 23 Jan 2009 11:56:31 +0000 (12:56 +0100)]
AVR32: macb - Search for PHY id
This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.
This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Olav Morken [Fri, 23 Jan 2009 11:56:26 +0000 (12:56 +0100)]
Fix IP alignment problem
This patch removes volatile from:
volatile IP_t *ip = (IP_t *)xip;
Due to a bug, avr32-gcc will assume that ip is aligned on a word boundary when
using volatile, which causes an exception since xip isn't aligned on a word
boundary.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ron Madrid [Thu, 29 Jan 2009 00:17:21 +0000 (16:17 -0800)]
Marvell
88E1118 interrupt fix
This patch adjusts the LED control so that interrupt lines are not reading LEDs
and effectively causing indefinite interrupts to the controller.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Stefan Roese [Wed, 21 Jan 2009 16:14:26 +0000 (17:14 +0100)]
net: smc911x.c: Add LAN9211 to chip_ids[] array
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Tue, 27 Jan 2009 21:53:39 +0000 (16:53 -0500)]
Move is_valid_ether_addr() to include/net.h
Import the is_valid_ether_addr() function from the Linux kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Michal Simek [Mon, 5 Jan 2009 11:25:13 +0000 (12:25 +0100)]
net: Sort Makefile labels
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Wolfgang Denk [Wed, 28 Jan 2009 22:14:22 +0000 (23:14 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Wolfgang Denk [Wed, 28 Jan 2009 22:06:42 +0000 (23:06 +0100)]
85xx: Fix compile breakage with sbc8540 and sbc8560
This fixes an error which raises just a warning:
sbc8560.c:250: warning: passing argument 2 of 'strmhz' makes integer from pointer without a cast
Signed-off-by: Wolfgang Denk <wd@denx.de>
Mike Frysinger [Wed, 28 Jan 2009 18:48:55 +0000 (13:48 -0500)]
SPD823TS: do not define CONFIG_CMD_ENV
Since the SPD823TS board does not actually have any writable flash to save
its environment, undefine CONFIG_CMD_ENV so the "saveenv" command is
disabled.
This fixes the build error:
common/libcommon.a(cmd_nvedit.o): In function `do_saveenv':
common/cmd_nvedit.c:557: undefined reference to `saveenv'
make: *** [u-boot] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Dirk Behme [Wed, 28 Jan 2009 20:40:16 +0000 (21:40 +0100)]
OMAP3: Add Zoom1 board support
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here:
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Dirk Behme [Wed, 28 Jan 2009 20:39:58 +0000 (21:39 +0100)]
OMAP3: Add Pandora support
Add Pandora support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Dirk Behme [Wed, 28 Jan 2009 20:39:58 +0000 (21:39 +0100)]
OMAP3: Add EVM board
Add EVM board support.
Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Dirk Behme [Wed, 28 Jan 2009 20:39:57 +0000 (21:39 +0100)]
OMAP3: Add Overo board
Add Overo board support.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Dirk Behme [Tue, 27 Jan 2009 17:19:12 +0000 (18:19 +0100)]
OMAP3: Add common power code, README, and BeagleBoard
Add BeagleBoard support, common power code and README.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Wolfgang Denk [Wed, 28 Jan 2009 20:09:46 +0000 (21:09 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Wolfgang Denk [Wed, 28 Jan 2009 20:09:32 +0000 (21:09 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Kumar Gala [Wed, 28 Jan 2009 14:31:10 +0000 (08:31 -0600)]
85xx: Fix compile breakage with MPC8540EVAL
Configuring for MPC8540EVAL board...
mpc8540eval.c: In function 'checkboard':
mpc8540eval.c:53: error: invalid operands to binary /
make[1]: *** [mpc8540eval.o] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Bryan Wu [Mon, 19 Jan 2009 04:04:27 +0000 (23:04 -0500)]
usb_scan_devices: fix output with no devices
We should check the return of usb_new_device() so that if no USB device is
found, we print out the right message rather than always saying "new usb
device found".
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Thu, 22 Jan 2009 09:11:21 +0000 (10:11 +0100)]
USB: Add high-speed (480Mb/s) to all USB related outputs
With this patch the USB related connection speed output ("usb tree" command and
debug output) is now high-speed enabled.
This patch also fixes a compilation warning when debugging is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Wed, 21 Jan 2009 16:12:19 +0000 (17:12 +0100)]
USB: Add dcache support to the EHCI driver
This patch adds routines to handle (flush/invalidate) the dcache for the
QH and qTD structures and data buffers. This is needed on platforms using
this EHCI support with dcache enabled (like the MIPS VCT board port).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Wed, 21 Jan 2009 16:12:28 +0000 (17:12 +0100)]
USB: Add EHCI support for VCT EHCI controller
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Wed, 21 Jan 2009 16:12:10 +0000 (17:12 +0100)]
USB: Add config option to call ehci_hcd_init() again after EHCI reset
This patch adds the config option CONFIG_EHCI_HCD_INIT_AFTER_RESET
to call ehci_hcd_init() again after ehci_reset() is executed. This
is needed for the upcoming VCT EHCI support which needs to re-init
the hcd part again after the EHCI CMD_RESET is executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Wed, 21 Jan 2009 16:12:01 +0000 (17:12 +0100)]
USB: Fix speed detection on EHCI cntr with root hub transaction translators
This patch fixes an issue that the speed of USB devices was not detected
correctly on some EHCI controllers. This will be used on the upcoming VCT
EHCI support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Thomas Abraham [Sun, 4 Jan 2009 04:11:20 +0000 (09:41 +0530)]
usb : musb : Enabling USB MSC support for DM6446 (TI DaVinci) platform
Enabling USB MSC support for DM6446 (TI DaVinci) platform in the
configuration file.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Thomas Abraham [Sun, 4 Jan 2009 04:11:16 +0000 (09:41 +0530)]
usb : musb : Enabling DM6446 (TI DaVinci) USB module power
Enabling DM6446 (TI DaVinci) USB module power and MUSB low-level
controller hook up to USB core layer.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Thomas Abraham [Sun, 4 Jan 2009 04:11:13 +0000 (09:41 +0530)]
usb : musb : Adding DM6446 (TI DaVinci) platform specific USB support
Adding DM6446 (TI DaVinci) platform specific USB functionality for
USB Phy and VBUS initialization.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Thomas Abraham [Sun, 4 Jan 2009 04:11:09 +0000 (09:41 +0530)]
usb : musb : Adding USB VBUS enable functionality for DM644x DVEVM
Adding USB VBUS enable functionality for DM644x DVEVM (TI DaVinci)
platform.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Thomas Abraham [Sun, 4 Jan 2009 04:11:03 +0000 (09:41 +0530)]
usb : musb : Adding host controller driver for Mentor USB controller
Adding Mentor USB core functionality and Mentor USB Host controller
functionality for Mentor USB OTG controller (musbhdrc).
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Mike Frysinger [Thu, 1 Jan 2009 23:27:27 +0000 (18:27 -0500)]
usb.h: use standard __LITTLE_ENDIAN from Linux headers
Rather than forcing people to define a custom "LITTLEENDIAN", just use the
__LITTLE_ENDIAN one from the Linux byteorder headers that every arch is
already setting up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Michael Trimarchi [Wed, 31 Dec 2008 09:33:56 +0000 (10:33 +0100)]
USB ehci ixp4xx support
Add USB ehci ixp4xx host controller. Test on ixdp465 board.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Michael Trimarchi [Wed, 31 Dec 2008 09:33:22 +0000 (10:33 +0100)]
USB ehci remove infinite loop and use handshake function
USB ehci code cleanup. Use handshake instead of infinite while loop
to check the STD_ASS status
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Michael Trimarchi [Wed, 31 Dec 2008 09:32:41 +0000 (10:32 +0100)]
Add initial support for USB ehci pci
Add USB ehci pci support. This patch doesn't include any
pci_ids and it is not tested on real hardware.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
projects / oweals / u-boot.git / log