Gregory CLEMENT [Tue, 9 May 2017 11:35:22 +0000 (13:35 +0200)]
arm64: mvebu: armada37xx: add pinctrl definition
Start to populate the device tree of the Armada 37xx with the pincontrol
configuration used on the board providing a dts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Gregory CLEMENT [Tue, 9 May 2017 11:35:32 +0000 (13:35 +0200)]
arm64: mvebu: Add pinctrl nodes for Armada 3700
Add the nodes for the two pin controller present in the Armada 37xx SoCs.
Initially the node was named gpio1 using the same name that for the
register range in the datasheet. However renaming it pinctr_nb (nb for
North Bridge) makes more sens.
Minor changes for U-Boot because of the slightly different dts version
done by Stefan Roese.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Tom Rini [Tue, 30 May 2017 18:07:23 +0000 (14:07 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
Philipp Tomsich [Mon, 15 May 2017 22:16:32 +0000 (00:16 +0200)]
doc: document u-boot, mmc-env-offset and u-boot, mmc-env-offset-redund
Adding documentation on the new config properties:
'u-boot,mmc-env-offset' - overrides CONFIG_ENV_OFFSET
'u-boot,mmc-env-offset-redundant'
- overrides CONFIG_ENV_OFFSET_REDUND
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Philipp Tomsich [Mon, 15 May 2017 22:16:31 +0000 (00:16 +0200)]
env_mmc: configure environment offsets via device tree
This introduces the ability to override the environment offets from the
device tree by setting the following nodes in '/config':
'u-boot,mmc-env-offset' - overrides CONFIG_ENV_OFFSET
'u-boot,mmc-env-offset-redundant'
- overrides CONFIG_ENV_OFFSET_REDUND
To keep with the previous logic, the CONFIG_* defines still need to
be available and the statically defined values become the defaults,
when the corresponding properties are not set in the device-tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Keerthy [Wed, 24 May 2017 04:49:27 +0000 (10:19 +0530)]
power: pmic: tps65218: Fix tps65218_voltage_update function
Currently while setting the vsel value for dcdc1 and dcdc2
the driver is wrongly masking the entire 8 bits in the process
clearing PFM (bit7) field as well. Hence describe an appropriate
mask for vsel field and modify only those bits in the vsel
mask.
Source: http://www.ti.com/lit/ds/symlink/tps65218.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes:
86db550b38 ("power: Add support for the TPS65218 PMIC")
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Heiner Kallweit [Fri, 14 Apr 2017 08:10:19 +0000 (10:10 +0200)]
mmc: meson: increase max block number per request
Number of blocks is a 9 bit field where 0 stands for a unlimited
number of blocks. Therefore the max number of blocks which can
be set is 511.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tom Rini [Wed, 10 May 2017 19:20:17 +0000 (15:20 -0400)]
drivers/power/regulator/max77686.c: Fix comparisons of unsigned expressions
Inside of
max77686_buck_volt2hex/max77686_buck_hex2volt/max77686_ldo_volt2hex we
check that the value we calculate is >= 0 however we declare 'hex' as
unsigned int making these always true. Mark these as 'int' instead. We
also move hex_max to int as they are constants that are 0x3f/0xff.
Given that the above functions are marked as returning an int, make the
variables we assign their return value to also be int to be able to
catch the error condition now. Reported by clang-3.8.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 10 May 2017 19:20:16 +0000 (15:20 -0400)]
mmc: Change 'part_config' to be a u8 not char.
In some places we check if part_config is set to MMCPART_NOAVAILABLE
(0xff). With part_config being a char this is always false. We should
be using a u8 to store this value instead, after a quick consultation
with the Linux Kernel. Reported by clang-3.8.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 26 May 2017 15:19:27 +0000 (11:19 -0400)]
Merge git://git.denx.de/u-boot-fsl-qoriq
Tom Rini [Fri, 26 May 2017 15:18:53 +0000 (11:18 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-nds32
Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
drivers/net/Kconfig
Tom Rini [Tue, 23 May 2017 20:22:03 +0000 (16:22 -0400)]
Merge branch 'rmobile' of git://git.denx.de/u-boot-sh
Udit Agarwal [Tue, 2 May 2017 12:13:57 +0000 (17:43 +0530)]
armv8: LS2080A: Adjust memory map for secure boot headers for NOR-boot
This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Santan Kumar [Fri, 28 Apr 2017 07:17:24 +0000 (12:47 +0530)]
armv8: ls2080ardb, ls2080aqds: Adjust memory map for NOR-boot
This patch adjusts memory map for images on LS2080ARDB and
LS2080AQDS NOR flash as below
Image Flash Offset
RCW+PBI 0x00000000
Boot firmware (U-Boot) 0x00100000
Boot firmware Environment 0x00300000
PPA firmware 0x00400000
PHY firmware 0x00980000
DPAA2 MC 0x00A00000
DPAA2 DPL 0x00D00000
DPAA2 DPC 0x00E00000
Kernel.itb 0x01000000
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Alison Wang [Tue, 16 May 2017 02:45:59 +0000 (10:45 +0800)]
armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1046A
This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Alison Wang [Tue, 16 May 2017 02:45:58 +0000 (10:45 +0800)]
armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1043A
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Alison Wang [Tue, 16 May 2017 02:45:57 +0000 (10:45 +0800)]
arm: ls1021a: Adjust memory mapping for Flash/SD card on LS1021AQDS/TWR
This patch is to adjust the memory mapping for FLash/SD card on
LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial
Flash, QE firmware load address and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Thu, 27 Apr 2017 09:38:07 +0000 (15:08 +0530)]
armv8: ls2080ardb: Add LS2081ARDB board support
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Thu, 27 Apr 2017 09:38:06 +0000 (15:08 +0530)]
armv8: fsl-layerscape: Add NXP LS2081A, LS2041A SoC support
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Fri, 28 Apr 2017 05:11:35 +0000 (10:41 +0530)]
armv8: ls2080ardb: Add QSPI-boot support
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Fri, 28 Apr 2017 05:11:34 +0000 (10:41 +0530)]
board: freescale: ls2080ardb: Update QIXIS code
Update QIXIS related code to be executed only if CONFIG_FSL_QIXIS
flag is enabled. In case QIXIS code is not enabled, use default
sysclk value as 100MHz per board documentation.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yogesh Gaur [Thu, 27 Apr 2017 04:44:16 +0000 (10:14 +0530)]
driver: net: fsl-mc: Update fsl_mc_ldpaa_exit() path
Earlier when MC is loaded but DPL is not deployed results in FDT
fix-up code execution hangs. For this case now print message on
console and return success instead of return -ENODEV. This update
allows fdt fixup to continue execution.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <Priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Tue, 25 Apr 2017 15:39:52 +0000 (08:39 -0700)]
armv8: ls1043ardb: Make NET independent of FMan
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
York Sun [Tue, 25 Apr 2017 15:39:51 +0000 (08:39 -0700)]
armv8: ls1046ardb: Make NET independent of FMan
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
Suresh Gupta [Tue, 25 Apr 2017 09:21:38 +0000 (14:51 +0530)]
armv8: ls1012a: fix the size of flash for multiple boards
LS1012AFRDM, LS1012ARDB, LS1012AQDS all have S25FS512S flash
of 64MB size.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Suresh Gupta [Tue, 25 Apr 2017 09:21:37 +0000 (14:51 +0530)]
armv8: layperscape: remove CONFIG_SPI_FLASH_BAR from some platforms
ls1012ardb, ls1046ardb, ls2080ardb have S25FS512S flash which does
not support Bank Address Register commands.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Tue, 25 Apr 2017 04:42:31 +0000 (10:12 +0530)]
board: freescale: ls2080ardb: Enable SD interface for RevF board
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 14 Apr 2017 08:49:01 +0000 (16:49 +0800)]
armv8: ls1046a: enable PCI command tool
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
rick [Tue, 23 May 2017 05:48:27 +0000 (13:48 +0800)]
nds32: eth: Support ftmac100 DM.
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
Boot linux kernel via dhcp and bootm ok.
NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4899 ms)
Using mac@
e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'boomimage-310y-ae300-spi.bin'.
Load address: 0x600000
Loading: #################################################################
#################################################################
#################################################################
...
...
###################################
233.4 KiB/s
done
Bytes transferred =
13872076 (d3abcc hex)
NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4592 ms)
Using mac@
e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'ae300.dtb'.
Load address: 0x2000000
Loading: #
82 KiB/s
done
Bytes transferred = 2378 (94a hex)
NDS32 # bootm 0x600000 - 0x2000000
Image Name:
Created: 2017-03-22 6:52:03 UTC
Image Type: NDS32 Linux Kernel Image (uncompressed)
Data Size:
13872012 Bytes = 13.2 MiB
Load Address:
0000c000
Entry Point:
0000c000
Verifying Checksum ... OK
Booting using the fdt blob at 0x2000000
Loading Kernel Image ... OK
Loading Device Tree to
01efc000, end
01eff949 ... OK
Linux version
3.10.102-20375-gb0034c1-dirty (rick@app09)
(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
#293 PREEMPT Wed Mar 22 14:49:28 CST 2017
CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick <rick@andestech.com>
Tom Rini [Mon, 22 May 2017 19:40:11 +0000 (15:40 -0400)]
mksunxi_fit_atf.sh: Allow for this to complete when bl31.bin is missing
In situations like an autobuilder we are likely to not have bl31.bin
present and thus would fail to build and propagate the error upwards.
Instead, print a big warning to stderr so that human will see that
something is wrong but complete the build.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 22 May 2017 18:15:16 +0000 (14:15 -0400)]
Merge git://git.denx.de/u-boot-sunxi
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 22 May 2017 18:14:57 +0000 (14:14 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Mon, 22 May 2017 18:14:44 +0000 (14:14 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-nds32
Lothar Waßmann [Thu, 18 May 2017 15:26:58 +0000 (17:26 +0200)]
ColdFire: Remove rogue 'CONFIG_SYS_NO_FLASH' embedded within another CONFIG_ name
The original commit for the MCF54418TWR ColdFire development board
support defined a 'CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN'
which obviously has a rogue 'CONFIG_SYS_NO_FLASH' embedded in the
intended 'CONFIG_SYS_FAULT_ECHO_LINK_DOWN' define.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Simon Glass [Wed, 17 May 2017 09:25:44 +0000 (03:25 -0600)]
sandbox: Enable CMD_GETTIME
Enable this option by default on sandbox to increase build coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:43 +0000 (03:25 -0600)]
Convert CONFIG_CMD_LZMADEC to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_LZMADEC
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:42 +0000 (03:25 -0600)]
Convert CONFIG_LZMA to Kconfig
This converts the following to Kconfig:
CONFIG_LZMA
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:41 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_LOADY
This is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:40 +0000 (03:25 -0600)]
Convert CONFIG_CMD_KGDB to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_KGDB
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:39 +0000 (03:25 -0600)]
Convert CONFIG_CMD_IRQ to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_IRQ
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:38 +0000 (03:25 -0600)]
fs: Kconfig: Add a separate option for FS_JFFS2
Rather than using CMD_JFFS2 for both the filesystem and its command, we
should have a separate option for each. This allows us to enable JFFS2
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:37 +0000 (03:25 -0600)]
Convert CONFIG_CMD_JFFS2 to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_JFFS2
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:36 +0000 (03:25 -0600)]
Convert CONFIG_CMD_IOTRACE to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_IOTRACE
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:35 +0000 (03:25 -0600)]
Convert CONFIG_CMD_IOLOOP to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_IOLOOP
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:34 +0000 (03:25 -0600)]
Convert CONFIG_CMD_IO to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_IO
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:33 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_IMX_FUSE
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:32 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_IMXOTP
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:31 +0000 (03:25 -0600)]
Convert CONFIG_CMD_IMMAP to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_IMMAP
Also move this command out of the cmd/ directory since it is
PowerPC-specific.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:30 +0000 (03:25 -0600)]
Kconfig: Add a CONFIG_IDE option
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:29 +0000 (03:25 -0600)]
Convert CONFIG_CMD_IDE to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_IDE
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:28 +0000 (03:25 -0600)]
Convert CONFIG_CMD_HDMIDETECT to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_HDMIDETECT
Note that we cannot do 'default y if VIDEO' because this option is only
enabled for a small subset of mx6 boards. Also this command is is not a
great implementation (it doesn't use driver model).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:27 +0000 (03:25 -0600)]
Convert CONFIG_CMD_HD44760 to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_HD44760
Also drop CONFIG_CMD_HD44780 which appears to be a typo.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 15:05:34 +0000 (09:05 -0600)]
Kconfig: Add CONFIG_HASH to enable hashing API
At present CONFIG_CMD_HASH enables the 'hash' command which also brings
in the hashing API. Some boards may wish to enable the API without the
command. Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:25 +0000 (03:25 -0600)]
Convert CONFIG_CMD_HASH to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:24 +0000 (03:25 -0600)]
Convert CONFIG_CMD_GSC to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_GSC
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:23 +0000 (03:25 -0600)]
Convert CONFIG_CMD_GETTIME to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_GETTIME
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:22 +0000 (03:25 -0600)]
Convert CONFIG_CMD_FUSE to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_FUSE
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:21 +0000 (03:25 -0600)]
Convert CONFIG_CMD_FPGA_LOADBP et al to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_FPGA_LOADBP
CONFIG_CMD_FPGA_LOADFS
CONFIG_CMD_FPGA_LOADMK
CONFIG_CMD_FPGA_LOADP
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:20 +0000 (03:25 -0600)]
Convert CONFIG_CMD_FPGAD to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_FPGAD
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:19 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_FDT_MAX_DUMP
This option is not used by any board. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:18 +0000 (03:25 -0600)]
Convert CONFIG_CMD_FDC to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_FDC
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:17 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ETHSW to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ETHSW
Also enable it for sandbox to increase build coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:16 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ESBC_VALIDATE to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ESBC_VALIDATE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:15 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ERRATA to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ERRATA
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:14 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ENV_FLAGS to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ENV_FLAGS
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:13 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ENV_CALLBACK to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ENV_CALLBACK
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:12 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_ENV
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:11 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ENTERRCM to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ENTERRCM
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:10 +0000 (03:25 -0600)]
Convert CONFIG_CMD_EEPROM et al to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:09 +0000 (03:25 -0600)]
Convert CONFIG_CMD_EECONFIG to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_EECONFIG
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:08 +0000 (03:25 -0600)]
Convert CONFIG_CMD_ECCTEST to Kconfig
This converts the following to Kconfig:
CONFIG_CMD_ECCTEST
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 May 2017 09:25:07 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_SYS_I2C_DS4510_ADDR
This is only used by one board and always set to 0x51. Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Wed, 17 May 2017 09:25:06 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_SYS_I2C_DS1621_ADDR
Now that dtt is gone, this is not used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:05 +0000 (03:25 -0600)]
Drop digital thermometer and thermostat (DTT) drivers
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:04 +0000 (03:25 -0600)]
Drop three-wire serial (TWS) support
This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.
Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 17 May 2017 09:25:03 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_SYS_I2C_DTT_ADDR
This option is only defined to a non-default value by canyonlands, which
needs conversion to driver model (where the I2C address would be defined
by the device tree).
Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Wed, 17 May 2017 09:25:02 +0000 (03:25 -0600)]
Convert CONFIG_DS4510 to Kconfig
This converts the following to Kconfig:
CONFIG_DS4510
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Wed, 17 May 2017 09:25:01 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_DS4510
This option enables a command in the driver. But the functions defined by
the driver are not called anywhere else in U-Boot. So it does not seem
useful to have this driver without its commands.
Drop this option, move the header file out of the common include/
directory and make all the function static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Wed, 17 May 2017 09:25:00 +0000 (03:25 -0600)]
Kconfig: Drop CONFIG_CMD_DS4510_RST
This option is only used in one driver and is not enabled by any board. It
does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Wed, 17 May 2017 09:24:59 +0000 (03:24 -0600)]
Kconfig: Drop CONFIG_CMD_DS4510_MEM
This option is only used in one driver and is not enabled by any board. It
does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Wed, 17 May 2017 09:24:58 +0000 (03:24 -0600)]
Kconfig: Drop CONFIG_CMD_DS4510_INFO
This option is only used in one driver and two boards. It does not seem
worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Mon, 15 May 2017 16:17:49 +0000 (12:17 -0400)]
lib: move hash CONFIG options to Kconfig
Commit
94e3c8c4fd7b ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 15 May 2017 16:17:48 +0000 (12:17 -0400)]
FIT: Rename FIT_DISABLE_SHA256 to FIT_ENABLE_SHA256_SUPPORT
We rename CONFIG_FIT_DISABLE_SHA256 to CONFIG_FIT_ENABLE_SHA256_SUPPORT which
is enabled by default and now a positive option. Convert the handful of boards
that were disabling it before to save space.
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 15 May 2017 12:29:02 +0000 (14:29 +0200)]
test: py: Add cmd_echo dependency
There is missing dependency on echo command. Mark tests which requires
echo.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Ley Foon Tan [Wed, 3 May 2017 09:13:32 +0000 (17:13 +0800)]
Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Hiroyuki Yokoyama [Sat, 13 May 2017 13:56:20 +0000 (15:56 +0200)]
usb: ehci: Add Renesas RCar M3/H3 EHCI support
Add a USB controller driver for the EHCI block in R8A7795/R8A7796 SoC.
This is a stopgap measure until we have proper DT support, clock and
reset framework in place, at which point we can switch to ehci-generic.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 13 May 2017 16:47:30 +0000 (01:47 +0900)]
ARM: rmobile: Move address of IICDVFS(I2C) to rcar-gen3-base.h
The IICDVFS(I2C) set in r8a7796.h is common in rcar-gen3.
This moves CONFIG_SYS_I2C_SH_BASE0 in rcar-gen3-base.h.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
rick [Thu, 18 May 2017 06:37:53 +0000 (14:37 +0800)]
nds32: Support AE3XX platform.
Support Andestech AE3xx platform: serial, timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
rick [Wed, 17 May 2017 02:59:20 +0000 (10:59 +0800)]
nds32: Support AG101P timer DM.
Support AG101P timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
rick [Mon, 17 Apr 2017 06:41:58 +0000 (14:41 +0800)]
nds32: Support AG101P serial DM.
Support AG101P serial device tree flow.
Signed-off-by: rick <rick@andestech.com>
Marek Vasut [Sat, 13 May 2017 13:57:53 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Add R8A7796 support
Add minor ifdeffery and default board config for the Salvator-XS board
with R8A7796 M3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:52 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Rename the defconfig to match the SoC
Rename the salvator-x_defconfig to r8a7795_salvator-x_defconfig in
preparation for the r8a7796 support on salvator-x board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:51 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Enable SCIF2 clock
There are two UARTs on the board, so enable the clock for the
second one as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:50 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Count all DRAM in all slots
Instead of counting only the DRAM in the first slot, count
all the DRAM in all slots and report it accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:49 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Add USB support
Add support for the EHCI USB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:48 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Add DVFS and PMIC support
Add support for rebooting the board using the ROHM BD9571MWV I2C PMIC,
but keep the CPU reboot option as a fallback.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:47 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Add RAVB ethernet support
Add support for the AVB ethernet on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:46 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Add SD support
Add support for the SD card slots on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:45 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Adjust UART clock
The UART uses internal SCIF clock except on R8A7795 H3 WS1.0 .
Use the internal clock and ignore the early version of the chip.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 13 May 2017 13:57:44 +0000 (15:57 +0200)]
ARM: rmobile: salvator-x: Zap redefined DECLARE_GLOBAL_DATA_PTR
The macro is used twice in the salvator-x board file, drop one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
projects / oweals / u-boot.git / log