From: Remy Bohmer <linux@bohmer.net>
Date: Tue, 3 Jun 2008 13:26:24 +0000 (+0200)
Subject: DM9000: Improve eth_reset() routine
X-Git-Tag: v1.3.4-rc1~108^2~7
X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=fbcb7ece0ea1e364180f1cf963e0fa0ce7f6560d;p=oweals%2Fu-boot.git

DM9000: Improve eth_reset() routine

According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the
reset procedure must be done twice to properly reset the DM9000 by means of software.
This errata is not needed anymore for the DM9000A, but it does not bother it.

This change has been tested with DM9000A, DM9000E, DM9000EP.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
---

diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c
index c6c24dd6fb..5b00e9588f 100644
--- a/drivers/net/dm9000x.c
+++ b/drivers/net/dm9000x.c
@@ -45,6 +45,8 @@ v1.2   03/18/2003       Weilun Huang <weilun_huang@davicom.com.tw>:
 			- Adapt eth_send such that it matches the DM9000*
 			  application notes. Needed to make it work properly
 			  for DM9000A.
+			- Adapted reset procedure to match DM9000 application
+			  notes (i.e. double reset)
 			These changes are tested with DM9000{A,EP,E} together
 			with a 200MHz Atmel AT91SAM92161 core
 
@@ -362,9 +364,35 @@ identify_nic(void)
 static void
 dm9000_reset(void)
 {
-	DM9000_DBG("resetting\n");
-	DM9000_iow(DM9000_NCR, NCR_RST);
-	udelay(1000);		/* delay 1ms */
+	DM9000_DBG("resetting DM9000\n");
+
+	/* Reset DM9000,
+	   see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */
+
+	/* DEBUG: Make all GPIO pins outputs */
+	DM9000_iow(DM9000_GPCR, 0x0F);
+	/* Step 1: Power internal PHY by writing 0 to GPIO0 pin */
+	DM9000_iow(DM9000_GPR, 0);
+	/* Step 2: Software reset */
+	DM9000_iow(DM9000_NCR, 3);
+
+	do {
+		DM9000_DBG("resetting the DM9000, 1st reset\n");
+		udelay(25); /* Wait at least 20 us */
+	} while (DM9000_ior(DM9000_NCR) & 1);
+
+	DM9000_iow(DM9000_NCR, 0);
+	DM9000_iow(DM9000_NCR, 3); /* Issue a second reset */
+
+	do {
+		DM9000_DBG("resetting the DM9000, 2nd reset\n");
+		udelay(25); /* Wait at least 20 us */
+	} while (DM9000_ior(DM9000_NCR) & 1);
+
+	/* Check whether the ethernet controller is present */
+	if ((DM9000_ior(DM9000_PIDL) != 0x0) ||
+	    (DM9000_ior(DM9000_PIDH) != 0x90))
+		printf("ERROR: resetting DM9000 -> not responding\n");
 }
 
 /* Initilize dm9000 board