From: Niklaus Giger Date: Sun, 4 Oct 2009 18:04:22 +0000 (+0200) Subject: ppc4xx: respect 80-chars per line in ppc*.h files X-Git-Tag: v2009.11-rc1~64 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=dbcc357166bed20df13450e93a501f30b197efd1;p=oweals%2Fu-boot.git ppc4xx: respect 80-chars per line in ppc*.h files After running checkstyle.pl on the three previous patches I noted that in the *.h files there were a lot of long lines. This patch solves this problem. Signed-off-by: Niklaus Giger Signed-off-by: Stefan Roese --- diff --git a/include/ppc405.h b/include/ppc405.h index 4c62249936..508c77b14e 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -29,9 +29,9 @@ #define PPC_128MB_SACR_VALUE(addr) PPC_REG_VAL(PPC_128MB_SACR_BIT(addr),1) #ifndef CONFIG_IOP480 -#define CONFIG_SYS_DCACHE_SIZE (16 << 10) /* For AMCC 405 CPUs */ +#define CONFIG_SYS_DCACHE_SIZE (16 << 10) /* For AMCC 405 CPUs */ #else -#define CONFIG_SYS_DCACHE_SIZE (2 << 10) /* For PLX IOP480 (403) */ +#define CONFIG_SYS_DCACHE_SIZE (2 << 10) /* For PLX IOP480(403)*/ #endif /****************************************************************************** @@ -71,10 +71,10 @@ * Decompression Controller ******************************************************************************/ #define DECOMP_DCR_BASE 0x14 -#define KIAR (DECOMP_DCR_BASE+0x0) /* Decompression controller addr reg */ -#define KIDR (DECOMP_DCR_BASE+0x1) /* Decompression controller data reg */ +#define KIAR (DECOMP_DCR_BASE+0x0) /* Decompression controller addr reg */ +#define KIDR (DECOMP_DCR_BASE+0x1) /* Decompression controller data reg */ /* values for kiar register - indirect addressing of these regs */ -#define KCONF 0x40 /* decompression core config register */ +#define KCONF 0x40 /* decompression core config register */ #endif /****************************************************************************** @@ -85,61 +85,61 @@ #else #define POWERMAN_DCR_BASE 0xb8 #endif -#define CPMSR (POWERMAN_DCR_BASE+0x0) /* Power management status */ -#define CPMER (POWERMAN_DCR_BASE+0x1) /* Power management enable */ -#define CPMFR (POWERMAN_DCR_BASE+0x2) /* Power management force */ +#define CPMSR (POWERMAN_DCR_BASE+0x0) /* Power management status */ +#define CPMER (POWERMAN_DCR_BASE+0x1) /* Power management enable */ +#define CPMFR (POWERMAN_DCR_BASE+0x2) /* Power management force */ /****************************************************************************** * Extrnal Bus Controller ******************************************************************************/ /* values for EBC0_CFGADDR register - indirect addressing of these regs */ - #define PB0CR 0x00 /* periph bank 0 config reg */ - #define PB1CR 0x01 /* periph bank 1 config reg */ - #define PB2CR 0x02 /* periph bank 2 config reg */ - #define PB3CR 0x03 /* periph bank 3 config reg */ - #define PB4CR 0x04 /* periph bank 4 config reg */ + #define PB0CR 0x00 /* periph bank 0 config reg */ + #define PB1CR 0x01 /* periph bank 1 config reg */ + #define PB2CR 0x02 /* periph bank 2 config reg */ + #define PB3CR 0x03 /* periph bank 3 config reg */ + #define PB4CR 0x04 /* periph bank 4 config reg */ #ifndef CONFIG_405EP - #define PB5CR 0x05 /* periph bank 5 config reg */ - #define PB6CR 0x06 /* periph bank 6 config reg */ - #define PB7CR 0x07 /* periph bank 7 config reg */ + #define PB5CR 0x05 /* periph bank 5 config reg */ + #define PB6CR 0x06 /* periph bank 6 config reg */ + #define PB7CR 0x07 /* periph bank 7 config reg */ #endif - #define PB0AP 0x10 /* periph bank 0 access parameters */ - #define PB1AP 0x11 /* periph bank 1 access parameters */ - #define PB2AP 0x12 /* periph bank 2 access parameters */ - #define PB3AP 0x13 /* periph bank 3 access parameters */ - #define PB4AP 0x14 /* periph bank 4 access parameters */ + #define PB0AP 0x10 /* periph bank 0 access parameters */ + #define PB1AP 0x11 /* periph bank 1 access parameters */ + #define PB2AP 0x12 /* periph bank 2 access parameters */ + #define PB3AP 0x13 /* periph bank 3 access parameters */ + #define PB4AP 0x14 /* periph bank 4 access parameters */ #ifndef CONFIG_405EP - #define PB5AP 0x15 /* periph bank 5 access parameters */ - #define PB6AP 0x16 /* periph bank 6 access parameters */ - #define PB7AP 0x17 /* periph bank 7 access parameters */ + #define PB5AP 0x15 /* periph bank 5 access parameters */ + #define PB6AP 0x16 /* periph bank 6 access parameters */ + #define PB7AP 0x17 /* periph bank 7 access parameters */ #endif - #define PBEAR 0x20 /* periph bus error addr reg */ - #define PBESR0 0x21 /* periph bus error status reg 0 */ - #define PBESR1 0x22 /* periph bus error status reg 1 */ -#define EBC0_CFG 0x23 /* external bus configuration reg */ + #define PBEAR 0x20 /* periph bus error addr reg */ + #define PBESR0 0x21 /* periph bus error status reg 0 */ + #define PBESR1 0x22 /* periph bus error status reg 1 */ +#define EBC0_CFG 0x23 /* external bus configuration reg */ #ifdef CONFIG_405EP /****************************************************************************** * Control ******************************************************************************/ #define CNTRL_DCR_BASE 0x0f0 -#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode register 0 */ -#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Clock status register */ -#define CPC0_EPCTL (CNTRL_DCR_BASE+0x3) /* EMAC to PHY control register */ -#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode register 1 */ -#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART control register */ -#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI control register */ - -#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */ -#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */ -#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */ -#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register*/ -#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */ -#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */ -#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */ -#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */ -#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */ -#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */ +#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode register 0 */ +#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Clock status register */ +#define CPC0_EPCTL (CNTRL_DCR_BASE+0x3) /* EMAC to PHY control register */ +#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode register 1 */ +#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART control register */ +#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI control register */ + +#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */ +#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */ +#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */ +#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register */ +#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */ +#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */ +#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */ +#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */ +#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */ +#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */ /* Bit definitions */ #define PLLMR0_CPU_DIV_MASK 0x00300000 /* CPU clock divider */ @@ -160,13 +160,13 @@ #define PLLMR0_OPB_PLB_DIV_3 0x00002000 #define PLLMR0_OPB_PLB_DIV_4 0x00003000 -#define PLLMR0_EXB_TO_PLB_MASK 0x00000300 /* External Bus:PLB Divisor */ +#define PLLMR0_EXB_TO_PLB_MASK 0x00000300 /* External Bus:PLB Divisor */ #define PLLMR0_EXB_PLB_DIV_2 0x00000000 #define PLLMR0_EXB_PLB_DIV_3 0x00000100 #define PLLMR0_EXB_PLB_DIV_4 0x00000200 #define PLLMR0_EXB_PLB_DIV_5 0x00000300 -#define PLLMR0_MAL_TO_PLB_MASK 0x00000030 /* MAL:PLB Divisor */ +#define PLLMR0_MAL_TO_PLB_MASK 0x00000030 /* MAL:PLB Divisor */ #define PLLMR0_MAL_PLB_DIV_1 0x00000000 #define PLLMR0_MAL_PLB_DIV_2 0x00000010 #define PLLMR0_MAL_PLB_DIV_3 0x00000020 @@ -180,7 +180,7 @@ #define PLLMR1_SSCS_MASK 0x80000000 /* Select system clock source */ #define PLLMR1_PLLR_MASK 0x40000000 /* PLL reset */ -#define PLLMR1_FBMUL_MASK 0x00F00000 /* PLL feedback multiplier value */ +#define PLLMR1_FBMUL_MASK 0x00F00000 /* PLL feedback multiplier value */ #define PLLMR1_FBMUL_DIV_16 0x00000000 #define PLLMR1_FBMUL_DIV_1 0x00100000 #define PLLMR1_FBMUL_DIV_2 0x00200000 @@ -198,7 +198,7 @@ #define PLLMR1_FBMUL_DIV_14 0x00E00000 #define PLLMR1_FBMUL_DIV_15 0x00F00000 -#define PLLMR1_FWDVA_MASK 0x00070000 /* PLL forward divider A value */ +#define PLLMR1_FWDVA_MASK 0x00070000 /* PLL forward divider A value */ #define PLLMR1_FWDVA_DIV_8 0x00000000 #define PLLMR1_FWDVA_DIV_7 0x00010000 #define PLLMR1_FWDVA_DIV_6 0x00020000 @@ -207,132 +207,132 @@ #define PLLMR1_FWDVA_DIV_3 0x00050000 #define PLLMR1_FWDVA_DIV_2 0x00060000 #define PLLMR1_FWDVA_DIV_1 0x00070000 -#define PLLMR1_FWDVB_MASK 0x00007000 /* PLL forward divider B value */ -#define PLLMR1_TUNING_MASK 0x000003FF /* PLL tune bits */ +#define PLLMR1_FWDVB_MASK 0x00007000 /* PLL forward divider B value */ +#define PLLMR1_TUNING_MASK 0x000003FF /* PLL tune bits */ /* Defines for CPC0_EPRCSR register */ -#define CPC0_EPRCSR_E0NFE 0x80000000 -#define CPC0_EPRCSR_E1NFE 0x40000000 -#define CPC0_EPRCSR_E1RPP 0x00000080 -#define CPC0_EPRCSR_E0RPP 0x00000040 -#define CPC0_EPRCSR_E1ERP 0x00000020 -#define CPC0_EPRCSR_E0ERP 0x00000010 -#define CPC0_EPRCSR_E1PCI 0x00000002 -#define CPC0_EPRCSR_E0PCI 0x00000001 +#define CPC0_EPRCSR_E0NFE 0x80000000 +#define CPC0_EPRCSR_E1NFE 0x40000000 +#define CPC0_EPRCSR_E1RPP 0x00000080 +#define CPC0_EPRCSR_E0RPP 0x00000040 +#define CPC0_EPRCSR_E1ERP 0x00000020 +#define CPC0_EPRCSR_E0ERP 0x00000010 +#define CPC0_EPRCSR_E1PCI 0x00000002 +#define CPC0_EPRCSR_E0PCI 0x00000001 /* Defines for CPC0_PCI Register */ -#define CPC0_PCI_SPE 0x00000010 /* PCIINT/WE select */ -#define CPC0_PCI_HOST_CFG_EN 0x00000008 /* PCI host config Enable */ -#define CPC0_PCI_ARBIT_EN 0x00000001 /* PCI Internal Arb Enabled*/ +#define CPC0_PCI_SPE 0x00000010 /* PCIINT/WE select */ +#define CPC0_PCI_HOST_CFG_EN 0x00000008 /* PCI host config Enable */ +#define CPC0_PCI_ARBIT_EN 0x00000001 /* PCI Internal Arb Enabled */ /* Defines for CPC0_BOOR Register */ -#define CPC0_BOOT_SEP 0x00000002 /* serial EEPROM present */ +#define CPC0_BOOT_SEP 0x00000002 /* serial EEPROM present */ /* Defines for CPC0_PLLMR1 Register fields */ -#define PLL_ACTIVE 0x80000000 -#define CPC0_PLLMR1_SSCS 0x80000000 -#define PLL_RESET 0x40000000 -#define CPC0_PLLMR1_PLLR 0x40000000 - /* Feedback multiplier */ -#define PLL_FBKDIV 0x00F00000 -#define CPC0_PLLMR1_FBDV 0x00F00000 -#define PLL_FBKDIV_16 0x00000000 -#define PLL_FBKDIV_1 0x00100000 -#define PLL_FBKDIV_2 0x00200000 -#define PLL_FBKDIV_3 0x00300000 -#define PLL_FBKDIV_4 0x00400000 -#define PLL_FBKDIV_5 0x00500000 -#define PLL_FBKDIV_6 0x00600000 -#define PLL_FBKDIV_7 0x00700000 -#define PLL_FBKDIV_8 0x00800000 -#define PLL_FBKDIV_9 0x00900000 -#define PLL_FBKDIV_10 0x00A00000 -#define PLL_FBKDIV_11 0x00B00000 -#define PLL_FBKDIV_12 0x00C00000 -#define PLL_FBKDIV_13 0x00D00000 -#define PLL_FBKDIV_14 0x00E00000 -#define PLL_FBKDIV_15 0x00F00000 - /* Forward A divisor */ -#define PLL_FWDDIVA 0x00070000 -#define CPC0_PLLMR1_FWDVA 0x00070000 -#define PLL_FWDDIVA_8 0x00000000 -#define PLL_FWDDIVA_7 0x00010000 -#define PLL_FWDDIVA_6 0x00020000 -#define PLL_FWDDIVA_5 0x00030000 -#define PLL_FWDDIVA_4 0x00040000 -#define PLL_FWDDIVA_3 0x00050000 -#define PLL_FWDDIVA_2 0x00060000 -#define PLL_FWDDIVA_1 0x00070000 - /* Forward B divisor */ -#define PLL_FWDDIVB 0x00007000 -#define CPC0_PLLMR1_FWDVB 0x00007000 -#define PLL_FWDDIVB_8 0x00000000 -#define PLL_FWDDIVB_7 0x00001000 -#define PLL_FWDDIVB_6 0x00002000 -#define PLL_FWDDIVB_5 0x00003000 -#define PLL_FWDDIVB_4 0x00004000 -#define PLL_FWDDIVB_3 0x00005000 -#define PLL_FWDDIVB_2 0x00006000 -#define PLL_FWDDIVB_1 0x00007000 - /* PLL tune bits */ +#define PLL_ACTIVE 0x80000000 +#define CPC0_PLLMR1_SSCS 0x80000000 +#define PLL_RESET 0x40000000 +#define CPC0_PLLMR1_PLLR 0x40000000 + /* Feedback multiplier */ +#define PLL_FBKDIV 0x00F00000 +#define CPC0_PLLMR1_FBDV 0x00F00000 +#define PLL_FBKDIV_16 0x00000000 +#define PLL_FBKDIV_1 0x00100000 +#define PLL_FBKDIV_2 0x00200000 +#define PLL_FBKDIV_3 0x00300000 +#define PLL_FBKDIV_4 0x00400000 +#define PLL_FBKDIV_5 0x00500000 +#define PLL_FBKDIV_6 0x00600000 +#define PLL_FBKDIV_7 0x00700000 +#define PLL_FBKDIV_8 0x00800000 +#define PLL_FBKDIV_9 0x00900000 +#define PLL_FBKDIV_10 0x00A00000 +#define PLL_FBKDIV_11 0x00B00000 +#define PLL_FBKDIV_12 0x00C00000 +#define PLL_FBKDIV_13 0x00D00000 +#define PLL_FBKDIV_14 0x00E00000 +#define PLL_FBKDIV_15 0x00F00000 + /* Forward A divisor */ +#define PLL_FWDDIVA 0x00070000 +#define CPC0_PLLMR1_FWDVA 0x00070000 +#define PLL_FWDDIVA_8 0x00000000 +#define PLL_FWDDIVA_7 0x00010000 +#define PLL_FWDDIVA_6 0x00020000 +#define PLL_FWDDIVA_5 0x00030000 +#define PLL_FWDDIVA_4 0x00040000 +#define PLL_FWDDIVA_3 0x00050000 +#define PLL_FWDDIVA_2 0x00060000 +#define PLL_FWDDIVA_1 0x00070000 + /* Forward B divisor */ +#define PLL_FWDDIVB 0x00007000 +#define CPC0_PLLMR1_FWDVB 0x00007000 +#define PLL_FWDDIVB_8 0x00000000 +#define PLL_FWDDIVB_7 0x00001000 +#define PLL_FWDDIVB_6 0x00002000 +#define PLL_FWDDIVB_5 0x00003000 +#define PLL_FWDDIVB_4 0x00004000 +#define PLL_FWDDIVB_3 0x00005000 +#define PLL_FWDDIVB_2 0x00006000 +#define PLL_FWDDIVB_1 0x00007000 + /* PLL tune bits */ #define PLL_TUNE_MASK 0x000003FF -#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ -#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ -#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ -#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ -#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ -#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ -#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ +#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ +#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ +#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ +#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ +#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ +#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ +#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ /* Defines for CPC0_PLLMR0 Register fields */ - /* CPU divisor */ -#define PLL_CPUDIV 0x00300000 -#define CPC0_PLLMR0_CCDV 0x00300000 -#define PLL_CPUDIV_1 0x00000000 -#define PLL_CPUDIV_2 0x00100000 -#define PLL_CPUDIV_3 0x00200000 -#define PLL_CPUDIV_4 0x00300000 - /* PLB divisor */ -#define PLL_PLBDIV 0x00030000 -#define CPC0_PLLMR0_CBDV 0x00030000 -#define PLL_PLBDIV_1 0x00000000 -#define PLL_PLBDIV_2 0x00010000 -#define PLL_PLBDIV_3 0x00020000 -#define PLL_PLBDIV_4 0x00030000 - /* OPB divisor */ -#define PLL_OPBDIV 0x00003000 -#define CPC0_PLLMR0_OPDV 0x00003000 -#define PLL_OPBDIV_1 0x00000000 -#define PLL_OPBDIV_2 0x00001000 -#define PLL_OPBDIV_3 0x00002000 -#define PLL_OPBDIV_4 0x00003000 - /* EBC divisor */ -#define PLL_EXTBUSDIV 0x00000300 -#define CPC0_PLLMR0_EPDV 0x00000300 -#define PLL_EXTBUSDIV_2 0x00000000 -#define PLL_EXTBUSDIV_3 0x00000100 -#define PLL_EXTBUSDIV_4 0x00000200 -#define PLL_EXTBUSDIV_5 0x00000300 - /* MAL divisor */ -#define PLL_MALDIV 0x00000030 -#define CPC0_PLLMR0_MPDV 0x00000030 -#define PLL_MALDIV_1 0x00000000 -#define PLL_MALDIV_2 0x00000010 -#define PLL_MALDIV_3 0x00000020 -#define PLL_MALDIV_4 0x00000030 - /* PCI divisor */ -#define PLL_PCIDIV 0x00000003 -#define CPC0_PLLMR0_PPFD 0x00000003 -#define PLL_PCIDIV_1 0x00000000 -#define PLL_PCIDIV_2 0x00000001 -#define PLL_PCIDIV_3 0x00000002 -#define PLL_PCIDIV_4 0x00000003 + /* CPU divisor */ +#define PLL_CPUDIV 0x00300000 +#define CPC0_PLLMR0_CCDV 0x00300000 +#define PLL_CPUDIV_1 0x00000000 +#define PLL_CPUDIV_2 0x00100000 +#define PLL_CPUDIV_3 0x00200000 +#define PLL_CPUDIV_4 0x00300000 + /* PLB divisor */ +#define PLL_PLBDIV 0x00030000 +#define CPC0_PLLMR0_CBDV 0x00030000 +#define PLL_PLBDIV_1 0x00000000 +#define PLL_PLBDIV_2 0x00010000 +#define PLL_PLBDIV_3 0x00020000 +#define PLL_PLBDIV_4 0x00030000 + /* OPB divisor */ +#define PLL_OPBDIV 0x00003000 +#define CPC0_PLLMR0_OPDV 0x00003000 +#define PLL_OPBDIV_1 0x00000000 +#define PLL_OPBDIV_2 0x00001000 +#define PLL_OPBDIV_3 0x00002000 +#define PLL_OPBDIV_4 0x00003000 + /* EBC divisor */ +#define PLL_EXTBUSDIV 0x00000300 +#define CPC0_PLLMR0_EPDV 0x00000300 +#define PLL_EXTBUSDIV_2 0x00000000 +#define PLL_EXTBUSDIV_3 0x00000100 +#define PLL_EXTBUSDIV_4 0x00000200 +#define PLL_EXTBUSDIV_5 0x00000300 + /* MAL divisor */ +#define PLL_MALDIV 0x00000030 +#define CPC0_PLLMR0_MPDV 0x00000030 +#define PLL_MALDIV_1 0x00000000 +#define PLL_MALDIV_2 0x00000010 +#define PLL_MALDIV_3 0x00000020 +#define PLL_MALDIV_4 0x00000030 + /* PCI divisor */ +#define PLL_PCIDIV 0x00000003 +#define CPC0_PLLMR0_PPFD 0x00000003 +#define PLL_PCIDIV_1 0x00000000 +#define PLL_PCIDIV_2 0x00000001 +#define PLL_PCIDIV_3 0x00000002 +#define PLL_PCIDIV_4 0x00000003 /* - *------------------------------------------------------------------------------- + *------------------------------------------------------------------------------ * PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI, * assuming a 33.3MHz input clock to the 405EP. - *------------------------------------------------------------------------------- + *------------------------------------------------------------------------------ */ #define PLLMR0_266_133_66 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ @@ -427,25 +427,25 @@ #define CPC0_PERD1 0x0e1 /* CPR_PERD1 */ #define CPC0_PERC0 0x180 /* CPR_PERC0 */ -#define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */ -#define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */ -#define CPR_PERD0_SPIDV_MASK 0x000F0000 /* SPI Clock Divider */ +#define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */ +#define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */ +#define CPR_PERD0_SPIDV_MASK 0x000F0000 /* SPI Clock Divider */ -#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */ +#define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */ -#define PLLD_FBDV_MASK 0x1F000000 /* PLL feedback divider value */ -#define PLLD_FWDVA_MASK 0x000F0000 /* PLL forward divider A value */ -#define PLLD_FWDVB_MASK 0x00000700 /* PLL forward divider B value */ +#define PLLD_FBDV_MASK 0x1F000000 /* PLL feedback divider value */ +#define PLLD_FWDVA_MASK 0x000F0000 /* PLL forward divider A value */ +#define PLLD_FWDVB_MASK 0x00000700 /* PLL forward divider B value */ -#define PRIMAD_CPUDV_MASK 0x0F000000 /* CPU Clock Divisor Mask */ -#define PRIMAD_PLBDV_MASK 0x000F0000 /* PLB Clock Divisor Mask */ -#define PRIMAD_OPBDV_MASK 0x00000F00 /* OPB Clock Divisor Mask */ -#define PRIMAD_EBCDV_MASK 0x0000000F /* EBC Clock Divisor Mask */ +#define PRIMAD_CPUDV_MASK 0x0F000000 /* CPU Clock Divisor Mask */ +#define PRIMAD_PLBDV_MASK 0x000F0000 /* PLB Clock Divisor Mask */ +#define PRIMAD_OPBDV_MASK 0x00000F00 /* OPB Clock Divisor Mask */ +#define PRIMAD_EBCDV_MASK 0x0000000F /* EBC Clock Divisor Mask */ -#define PERD0_PWMDV_MASK 0xFF000000 /* PWM Divider Mask */ -#define PERD0_SPIDV_MASK 0x000F0000 /* SPI Divider Mask */ -#define PERD0_U0DV_MASK 0x0000FF00 /* UART 0 Divider Mask */ -#define PERD0_U1DV_MASK 0x000000FF /* UART 1 Divider Mask */ +#define PERD0_PWMDV_MASK 0xFF000000 /* PWM Divider Mask */ +#define PERD0_SPIDV_MASK 0x000F0000 /* SPI Divider Mask */ +#define PERD0_U0DV_MASK 0x0000FF00 /* UART 0 Divider Mask */ +#define PERD0_U1DV_MASK 0x000000FF /* UART 1 Divider Mask */ #else /* #ifdef CONFIG_405EP */ /****************************************************************************** @@ -462,13 +462,13 @@ #define CPC0_ECR 0xaa /* edge conditioner register */ /* Bit definitions */ -#define PLLMR_FWD_DIV_MASK 0xE0000000 /* Forward Divisor */ +#define PLLMR_FWD_DIV_MASK 0xE0000000 /* Forward Divisor */ #define PLLMR_FWD_DIV_BYPASS 0xE0000000 #define PLLMR_FWD_DIV_3 0xA0000000 #define PLLMR_FWD_DIV_4 0x80000000 #define PLLMR_FWD_DIV_6 0x40000000 -#define PLLMR_FB_DIV_MASK 0x1E000000 /* Feedback Divisor */ +#define PLLMR_FB_DIV_MASK 0x1E000000 /* Feedback Divisor */ #define PLLMR_FB_DIV_1 0x02000000 #define PLLMR_FB_DIV_2 0x04000000 #define PLLMR_FB_DIV_3 0x06000000 @@ -476,32 +476,32 @@ #define PLLMR_TUNING_MASK 0x01F80000 -#define PLLMR_CPU_TO_PLB_MASK 0x00060000 /* CPU:PLB Frequency Divisor */ +#define PLLMR_CPU_TO_PLB_MASK 0x00060000 /* CPU:PLB Frequency Divisor */ #define PLLMR_CPU_PLB_DIV_1 0x00000000 #define PLLMR_CPU_PLB_DIV_2 0x00020000 #define PLLMR_CPU_PLB_DIV_3 0x00040000 #define PLLMR_CPU_PLB_DIV_4 0x00060000 -#define PLLMR_OPB_TO_PLB_MASK 0x00018000 /* OPB:PLB Frequency Divisor */ +#define PLLMR_OPB_TO_PLB_MASK 0x00018000 /* OPB:PLB Frequency Divisor */ #define PLLMR_OPB_PLB_DIV_1 0x00000000 #define PLLMR_OPB_PLB_DIV_2 0x00008000 #define PLLMR_OPB_PLB_DIV_3 0x00010000 #define PLLMR_OPB_PLB_DIV_4 0x00018000 -#define PLLMR_PCI_TO_PLB_MASK 0x00006000 /* PCI:PLB Frequency Divisor */ +#define PLLMR_PCI_TO_PLB_MASK 0x00006000 /* PCI:PLB Frequency Divisor */ #define PLLMR_PCI_PLB_DIV_1 0x00000000 #define PLLMR_PCI_PLB_DIV_2 0x00002000 #define PLLMR_PCI_PLB_DIV_3 0x00004000 #define PLLMR_PCI_PLB_DIV_4 0x00006000 -#define PLLMR_EXB_TO_PLB_MASK 0x00001800 /* External Bus:PLB Divisor */ +#define PLLMR_EXB_TO_PLB_MASK 0x00001800 /* External Bus:PLB Divisor */ #define PLLMR_EXB_PLB_DIV_2 0x00000000 #define PLLMR_EXB_PLB_DIV_3 0x00000800 #define PLLMR_EXB_PLB_DIV_4 0x00001000 #define PLLMR_EXB_PLB_DIV_5 0x00001800 /* definitions for PPC405GPr (new mode strapping) */ -#define PLLMR_FWDB_DIV_MASK 0x00000007 /* Forward Divisor B */ +#define PLLMR_FWDB_DIV_MASK 0x00000007 /* Forward Divisor B */ #define PSR_PLL_FWD_MASK 0xC0000000 #define PSR_PLL_FDBACK_MASK 0x30000000 @@ -513,15 +513,15 @@ #define PSR_ROM_WIDTH_MASK 0x00018000 #define PSR_ROM_LOC 0x00004000 #define PSR_PCI_ASYNC_EN 0x00001000 -#define PSR_PERCLK_SYNC_MODE_EN 0x00000800 /* PPC405GPr only */ +#define PSR_PERCLK_SYNC_MODE_EN 0x00000800 /* PPC405GPr only */ #define PSR_PCI_ARBIT_EN 0x00000400 -#define PSR_NEW_MODE_EN 0x00000020 /* PPC405GPr only */ +#define PSR_NEW_MODE_EN 0x00000020 /* PPC405GPr only */ #ifndef CONFIG_IOP480 /* * PLL Voltage Controlled Oscillator (VCO) definitions * Maximum and minimum values (in MHz) for correct PLL operation. - */ +*/ #define VCO_MIN 400 #define VCO_MAX 800 #endif /* #ifndef CONFIG_IOP480 */ @@ -535,35 +535,35 @@ #else #define MAL_DCR_BASE 0x180 #endif -#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */ -#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Err Status (Read/Clear)*/ -#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */ -#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set)*/ -#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset)*/ -#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status*/ -#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int reg */ -#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */ -#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */ -#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status*/ -#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int reg */ -#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table ptr */ -#define MAL0_TXCTP1R (MAL_DCR_BASE + 0x21) /* TX 1 Channel table ptr */ -#define MAL0_TXCTP2R (MAL_DCR_BASE + 0x22) /* TX 2 Channel table ptr */ -#define MAL0_TXCTP3R (MAL_DCR_BASE + 0x23) /* TX 3 Channel table ptr */ -#define MAL0_RXCTP0R (MAL_DCR_BASE + 0x40) /* RX 0 Channel table ptr */ -#define MAL0_RXCTP1R (MAL_DCR_BASE + 0x41) /* RX 1 Channel table ptr */ -#define MAL0_RXCTP2R (MAL_DCR_BASE + 0x42) /* RX 2 Channel table ptr */ -#define MAL0_RXCTP3R (MAL_DCR_BASE + 0x43) /* RX 3 Channel table ptr */ -#define MAL0_RXCTP8R (MAL_DCR_BASE + 0x48) /* RX 8 Channel table ptr */ -#define MAL0_RXCTP16R (MAL_DCR_BASE + 0x50) /* RX 16 Channel table ptr */ -#define MAL0_RXCTP24R (MAL_DCR_BASE + 0x58) /* RX 24 Channel table ptr */ -#define MAL0_RCBS0 (MAL_DCR_BASE + 0x60) /* RX 0 Channel buffer size */ -#define MAL0_RCBS1 (MAL_DCR_BASE + 0x61) /* RX 1 Channel buffer size */ -#define MAL0_RCBS2 (MAL_DCR_BASE + 0x62) /* RX 2 Channel buffer size */ -#define MAL0_RCBS3 (MAL_DCR_BASE + 0x63) /* RX 3 Channel buffer size */ -#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */ -#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */ -#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */ +#define MAL0_CFG (MAL_DCR_BASE + 0x00) /* MAL Config reg */ +#define MAL0_ESR (MAL_DCR_BASE + 0x01) /* Err Status (Read/Clear) */ +#define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */ +#define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set) */ +#define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset) */ +#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status */ +#define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int reg */ +#define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */ +#define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */ +#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status */ +#define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int reg */ +#define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table ptr */ +#define MAL0_TXCTP1R (MAL_DCR_BASE + 0x21) /* TX 1 Channel table ptr */ +#define MAL0_TXCTP2R (MAL_DCR_BASE + 0x22) /* TX 2 Channel table ptr */ +#define MAL0_TXCTP3R (MAL_DCR_BASE + 0x23) /* TX 3 Channel table ptr */ +#define MAL0_RXCTP0R (MAL_DCR_BASE + 0x40) /* RX 0 Channel table ptr */ +#define MAL0_RXCTP1R (MAL_DCR_BASE + 0x41) /* RX 1 Channel table ptr */ +#define MAL0_RXCTP2R (MAL_DCR_BASE + 0x42) /* RX 2 Channel table ptr */ +#define MAL0_RXCTP3R (MAL_DCR_BASE + 0x43) /* RX 3 Channel table ptr */ +#define MAL0_RXCTP8R (MAL_DCR_BASE + 0x48) /* RX 8 Channel table ptr */ +#define MAL0_RXCTP16R (MAL_DCR_BASE + 0x50) /* RX 16 Channel table ptr */ +#define MAL0_RXCTP24R (MAL_DCR_BASE + 0x58) /* RX 24 Channel table ptr */ +#define MAL0_RCBS0 (MAL_DCR_BASE + 0x60) /* RX 0 Channel buffer size */ +#define MAL0_RCBS1 (MAL_DCR_BASE + 0x61) /* RX 1 Channel buffer size */ +#define MAL0_RCBS2 (MAL_DCR_BASE + 0x62) /* RX 2 Channel buffer size */ +#define MAL0_RCBS3 (MAL_DCR_BASE + 0x63) /* RX 3 Channel buffer size */ +#define MAL0_RCBS8 (MAL_DCR_BASE + 0x68) /* RX 8 Channel buffer size */ +#define MAL0_RCBS16 (MAL_DCR_BASE + 0x70) /* RX 16 Channel buffer size */ +#define MAL0_RCBS24 (MAL_DCR_BASE + 0x78) /* RX 24 Channel buffer size */ /*----------------------------------------------------------------------------- | IIC Register Offsets @@ -610,7 +610,7 @@ #define OCM0_DSRC2 (OCM_DCR_BASE + 0x09) /* OCM D-side Bank 2 Config */ #define OCM0_ISRC1 (OCM_DCR_BASE + 0x0A) /* OCM I-side Bank 1Config */ #define OCM0_ISRC2 (OCM_DCR_BASE + 0x0B) /* OCM I-side Bank 2 Config */ -#define OCM0_DISDPC (OCM_DCR_BASE + 0x0C) /* OCM D-/I-side Data Par Chk*/ +#define OCM0_DISDPC (OCM_DCR_BASE + 0x0C) /* OCM D-/I-side Data Par Chk */ #else #define OCM_DCR_BASE 0x018 #define OCM0_ISCNTL (OCM_DCR_BASE+0x01) /* OCM I-side control reg */ @@ -746,14 +746,14 @@ #define SDR0_MFR 0x4300 /* SDR0_MFR reg */ /* Defines for CPC0_EPRCSR register */ -#define CPC0_EPRCSR_E0NFE 0x80000000 -#define CPC0_EPRCSR_E1NFE 0x40000000 -#define CPC0_EPRCSR_E1RPP 0x00000080 -#define CPC0_EPRCSR_E0RPP 0x00000040 -#define CPC0_EPRCSR_E1ERP 0x00000020 -#define CPC0_EPRCSR_E0ERP 0x00000010 -#define CPC0_EPRCSR_E1PCI 0x00000002 -#define CPC0_EPRCSR_E0PCI 0x00000001 +#define CPC0_EPRCSR_E0NFE 0x80000000 +#define CPC0_EPRCSR_E1NFE 0x40000000 +#define CPC0_EPRCSR_E1RPP 0x00000080 +#define CPC0_EPRCSR_E0RPP 0x00000040 +#define CPC0_EPRCSR_E1ERP 0x00000020 +#define CPC0_EPRCSR_E0ERP 0x00000010 +#define CPC0_EPRCSR_E1PCI 0x00000002 +#define CPC0_EPRCSR_E0PCI 0x00000001 #define CPR0_CLKUPD 0x020 #define CPR0_PLLC 0x040 @@ -770,46 +770,46 @@ /* CUST0 Customer Configuration Register0 */ #define SDR0_CUST0 0x4000 -#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ -#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */ -#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */ -#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */ - -#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */ -#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */ -#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */ - -#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */ -#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */ -#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */ - -#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */ -#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24) -#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F) - -#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */ -#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22) -#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03) - -#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */ -#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */ -#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */ - -#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */ -#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */ -#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */ - -#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */ -#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4) -#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF) - -#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */ -#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */ -#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Select Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */ +#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ +#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */ +#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */ +#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */ + +#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */ +#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */ +#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */ + +#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */ +#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width= 16 Bit */ +#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width= 8 Bit */ + +#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */ +#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24) +#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F) + +#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */ +#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22) +#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03) + +#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */ +#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */ +#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */ + +#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */ +#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */ +#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */ + +#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */ +#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4) +#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF) + +#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Sel Gating Mask */ +#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Sel Gating Disable */ +#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Sel Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Sel0 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Sel1 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Sel2 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Sel3 Gating Enable */ #define SDR0_PFC0 0x4100 #define SDR0_PFC1 0x4101 diff --git a/include/ppc440.h b/include/ppc440.h index 9299a7172a..fe0db93b51 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -48,7 +48,7 @@ #ifndef __PPC440_H__ #define __PPC440_H__ -#define CONFIG_SYS_DCACHE_SIZE (32 << 10) /* For AMCC 440 CPUs */ +#define CONFIG_SYS_DCACHE_SIZE (32 << 10) /* For AMCC 440 CPUs */ /****************************************************************************** * DCRs & Related @@ -86,8 +86,8 @@ #define SDR0_XPLLC 0x01c1 #define SDR0_XPLLD 0x01c2 #define SDR0_SRST 0x0200 -#define SD0_AMP0 0x0240 /* Override PLB4 prioritiy for up to 8 masters */ -#define SD0_AMP1 0x0241 /* Override PLB3 prioritiy for up to 8 masters */ +#define SD0_AMP0 0x0240 /* Override PLB4 prioritiy for up to 8 masters */ +#define SD0_AMP1 0x0241 /* Override PLB3 prioritiy for up to 8 masters */ #if defined(CONFIG_460EX) || defined(CONFIG_460GT) #define SDR0_PCI0 0x01c0 #else @@ -145,10 +145,10 @@ #define SDR0_XCR2 0x01c6 #define SDR0_XPLLC0 0x01c1 #define SDR0_XPLLD0 0x01c2 -#define SDR0_XPLLC1 0x01c4 /*notRCW - SG */ -#define SDR0_XPLLD1 0x01c5 /*notRCW - SG */ -#define SDR0_XPLLC2 0x01c7 /*notRCW - SG */ -#define SDR0_XPLLD2 0x01c8 /*notRCW - SG */ +#define SDR0_XPLLC1 0x01c4 /* notRCW - SG */ +#define SDR0_XPLLD1 0x01c5 /* notRCW - SG */ +#define SDR0_XPLLC2 0x01c7 /* notRCW - SG */ +#define SDR0_XPLLD2 0x01c8 /* dnotRCW - SG */ #define SD0_AMP0 0x0240 #define SD0_AMP1 0x0241 #define SDR0_CUST2 0x4004 @@ -187,80 +187,91 @@ #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) -/* PLB3 Arbiter */ + /* PLB3 Arbiter */ #define PLB3_DCR_BASE 0x070 #define PLB3_ACR (PLB3_DCR_BASE + 0x7) -/* PLB4 Arbiter - PowerPC440EP Pass1 */ + /* PLB4 Arbiter - PowerPC440EP Pass1 */ #define PLB4_DCR_BASE 0x080 #define PLB4_ACR (PLB4_DCR_BASE + 0x1) #define PLB4_ACR_WRP (0x80000000 >> 7) -/* Pin Function Control Register 1 */ + /* Pin Function Control Register 1 */ #define SDR0_PFC1 0x4101 -#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ -#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ -#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ -#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ -#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ -#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ -#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ -#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ -#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ -#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ -#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ -#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ -#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */ -#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ -#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ -#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */ -#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ -#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ -#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */ -#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ -#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ -#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */ -#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */ -#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */ - -#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */ -#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */ -#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ -#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ - -/* USB Control Register */ +#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ +#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ +#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ +#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ +#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ +#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ +#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ +#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ +#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ +#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ +#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ +#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ +#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold + Req Selection */ +#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ +#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ +#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) + Selection */ +#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ +#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ +#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) + Selection */ +#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. + Selected */ +#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ +#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject + Selection */ +#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject + Disable */ +#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject + Enable */ + +#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor Enable + Selection */ +#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor + Enable */ +#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor + Enable */ +#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation + Gated In */ + + /* USB Control Register */ #define SDR0_USB0 0x0320 -#define SDR0_USB0_USB_DEVSEL_MASK 0x00000002 /* USB Device Selection */ -#define SDR0_USB0_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */ -#define SDR0_USB0_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */ -#define SDR0_USB0_LEEN_MASK 0x00000001 /* Little Endian selection */ -#define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ -#define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ - -/* Miscealleneaous Function Reg. */ +#define SDR0_USB0_USB_DEVSEL_MASK 0x00000002 /* USB Device Selection */ +#define SDR0_USB0_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */ +#define SDR0_USB0_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */ +#define SDR0_USB0_LEEN_MASK 0x00000001 /* Little Endian selection */ +#define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ +#define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ + + /* Miscealleneaous Function Reg. */ #define SDR0_MFR 0x4300 -#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ -#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 -#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ -#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 -#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ -#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ -#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ -#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ -#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ -#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ -#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ -#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) -#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) - -#define SDR0_MFR_ERRATA3_EN0 0x00800000 -#define SDR0_MFR_ERRATA3_EN1 0x00400000 -#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ -#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */ -#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ -#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ -#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ +#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ +#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) + +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ #define GPT0_COMP6 0x00000098 #define GPT0_COMP5 0x00000094 @@ -278,245 +289,296 @@ #if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define SDR0_USB2D0CR 0x0320 -#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC Master Selection */ -#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection */ -#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */ - -#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface Selection */ -#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */ -#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */ - -#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */ -#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ -#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ - -/* USB2 Host Control Register */ -#define SDR0_USB2H0CR 0x0340 -#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface */ -#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */ -#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */ -#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length Adjustment */ - -/* Pin Function Control Register 1 */ -#define SDR0_PFC1 0x4101 -#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ -#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ -#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ - -#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select EMAC 0 */ -#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII bridge */ -#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ -#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII bridge */ -#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII bridge */ -#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII bridge */ -#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII bridge */ -#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII bridge */ - -#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ -#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ -#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ -#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ -#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ -#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ -#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ -#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ -#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ -#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */ -#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ -#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ -#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */ -#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ -#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ -#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */ -#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ -#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ -#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */ -#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */ -#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */ - -#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */ -#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */ -#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ -#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ - -/* Ethernet PLL Configuration Register */ -#define SDR0_PFC2 0x4102 -#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */ -#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication selector */ -#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */ -#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */ - -#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */ -#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */ -#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ -#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */ -#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */ -#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */ -#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */ -#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */ +#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC + Master Selection */ +#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection*/ +#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */ + +#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface + Selection */ +#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */ +#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */ + +#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */ +#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ +#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ + + /* USB2 Host Control Register */ +#define SDR0_USB2H0CR 0x0340 +#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface*/ +#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */ +#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */ +#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length + Adjustment */ + + /* Pin Function Control Register 1 */ +#define SDR0_PFC1 0x4101 +#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ +#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ +#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ + +#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select + EMAC 0 */ +#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII + bridge */ +#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII + bridge */ +#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII + bridge */ +#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII + bridge */ +#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII + bridge */ +#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII + bridge */ +#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII + bridge */ + +#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ +#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ +#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ +#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ +#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ +#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ +#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ +#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ +#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ +#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req + Selection */ +#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ +#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ +#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) + Selection */ +#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ +#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ +#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) + Selection */ +#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ +#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ +#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject + Selection */ +#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject + Disable */ +#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject + Enable */ + +#define SDR0_PFC1_PLB_PME_MASK 0x00001000 + /* PLB3/PLB4 Perf. Monitor En. Selection */ +#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 + /* PLB3 Performance Monitor Enable */ +#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 + /* PLB3 Performance Monitor Enable */ +#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation + Gated In */ + + /* Ethernet PLL Configuration Register */ +#define SDR0_PFC2 0x4102 +#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */ +#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication + selector */ +#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */ +#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */ + +#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */ +#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */ #define SDR0_PFC4 0x4104 -/* USB2PHY0 Control Register */ -#define SDR0_USB2PHY0CR 0x4103 -#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000 /* PHY UTMI interface connection */ -#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */ -#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */ - -#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */ -#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */ -#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */ - -#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000 /* VBus detect (Device mode only) */ -#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000 /* Pull-up resistance on D+ is disabled */ -#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000 /* Pull-up resistance on D+ is enabled */ - -#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000 /* PHY UTMI data width and clock select */ -#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */ -#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */ - -#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */ -#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */ -#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000 /* Loop back enabled (only test purposes) */ - -#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000 /* Force XO block on during a suspend */ -#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */ -#define SDR0_USB2PHY0CR_XO_OFF 0x04000000 /* PHY XO block is powered-off when all ports are suspended */ - -#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */ -#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */ -#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only for full-speed operation */ - -#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock source */ -#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal 48M clock as a reference */ -#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO block output as a reference */ - -#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO block */ -#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external clock */ -#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock from a crystal */ - -#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */ -#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq = 12 MHz*/ -#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq = 48 MHz*/ -#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq = 24 MHz*/ - -/* Miscealleneaous Function Reg. */ -#define SDR0_MFR 0x4300 -#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ -#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 -#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ -#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 -#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ -#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ -#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ -#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ -#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ -#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) -#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) - -#define SDR0_MFR_ERRATA3_EN0 0x00800000 -#define SDR0_MFR_ERRATA3_EN1 0x00400000 -#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ -#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */ -#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ -#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ -#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ + /* USB2PHY0 Control Register */ +#define SDR0_USB2PHY0CR 0x4103 +#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000 + + /* PHY UTMI interface connection */ +#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */ +#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */ + +#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */ +#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */ +#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */ + +#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000 + /* VBus detect (Device mode only) */ +#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000 + /* Pull-up resistance on D+ is disabled */ +#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000 + /* Pull-up resistance on D+ is enabled */ + +#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000 + /* PHY UTMI data width and clock select */ +#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */ +#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */ + +#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */ +#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */ +#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000 + /* Loop back enabled (only test purposes) */ + +#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000 + /* Force XO block on during a suspend */ +#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */ +#define SDR0_USB2PHY0CR_XO_OFF 0x04000000 + /* PHY XO block is powered-off when all ports are suspended */ + +#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */ +#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */ +#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only + for full-speed operation */ + +#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock + source */ +#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal + 48M clock as a reference */ +#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO + block output as a reference */ + +#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO + block*/ +#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external + clock */ +#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock + from a crystal */ + +#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */ +#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq + = 12 MHz */ +#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq + = 48 MHz */ +#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq + = 24 MHz */ + + /* Miscealleneaous Function Reg. */ +#define SDR0_MFR 0x4300 +#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) + +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Ena. on both EMAC3 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ #endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */ -/* CUST1 Customer Configuration Register1 */ -#define SDR0_CUST1 0x4002 -#define SDR0_CUST1_NDRSC_MASK 0xFFFF0000 /* NDRSC Device Read Count */ -#define SDR0_CUST1_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16) -#define SDR0_CUST1_NDRSC_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF) - -/* Pin Function Control Register 0 */ -#define SDR0_PFC0 0x4100 -#define SDR0_PFC0_CPU_TR_EN_MASK 0x00000100 /* CPU Trace Enable Mask */ -#define SDR0_PFC0_CPU_TRACE_EN 0x00000100 /* CPU Trace Enable */ -#define SDR0_PFC0_CPU_TRACE_DIS 0x00000100 /* CPU Trace Disable */ -#define SDR0_PFC0_CTE_ENCODE(n) ((((unsigned long)(n))&0x01)<<8) -#define SDR0_PFC0_CTE_DECODE(n) ((((unsigned long)(n))>>8)&0x01) - -/* Pin Function Control Register 1 */ -#define SDR0_PFC1 0x4101 -#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ -#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ -#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ -#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ -#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ -#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ -#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ -#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ -#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ -#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ -#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ -#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ -#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */ -#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ -#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ -#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */ -#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ -#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ -#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */ -#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ -#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ -#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */ -#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */ -#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */ - -#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */ -#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */ -#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ -#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ + /* CUST1 Customer Configuration Register1 */ +#define SDR0_CUST1 0x4002 +#define SDR0_CUST1_NDRSC_MASK 0xFFFF0000 /* NDRSC Device Read Count */ +#define SDR0_CUST1_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16) +#define SDR0_CUST1_NDRSC_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF) + + /* Pin Function Control Register 0 */ +#define SDR0_PFC0 0x4100 +#define SDR0_PFC0_CPU_TR_EN_MASK 0x00000100 /* CPU Trace Enable Mask */ +#define SDR0_PFC0_CPU_TRACE_EN 0x00000100 /* CPU Trace Enable */ +#define SDR0_PFC0_CPU_TRACE_DIS 0x00000100 /* CPU Trace Disable */ +#define SDR0_PFC0_CTE_ENCODE(n) ((((unsigned long)(n))&0x01)<<8) +#define SDR0_PFC0_CTE_DECODE(n) ((((unsigned long)(n))>>8)&0x01) + + /* Pin Function Control Register 1 */ +#define SDR0_PFC1 0x4101 +#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ +#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ +#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ +#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ +#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ +#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ +#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ +#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ +#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ +#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ +#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ +#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ +#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req + Selection */ +#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ +#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ +#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) + Selection */ +#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ +#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ +#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) + Selection */ +#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ +#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ +#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject + Selection */ +#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject + Disable */ +#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject + Enable */ + +#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. + Selection */ +#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor + Enable */ +#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor + Enable */ +#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation + Gated In */ #endif /* 440EP || 440GR || 440EPX || 440GRX */ #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ defined(CONFIG_460EX) || defined(CONFIG_460GT) -/* CUST0 Customer Configuration Register0 */ -#define SDR0_CUST0 0x4000 -#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ -#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */ -#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */ -#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */ - -#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */ -#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */ -#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */ - -#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */ -#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */ -#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */ - -#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */ -#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24) -#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F) - -#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */ -#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22) -#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03) - -#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */ -#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */ -#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */ - -#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */ -#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */ -#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */ - -#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */ -#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4) -#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF) - -#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */ -#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */ -#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Select Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */ -#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */ + /* CUST0 Customer Configuration Register0 */ +#define SDR0_CUST0 0x4000 +#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ +#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */ +#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */ +#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */ + +#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */ +#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */ +#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */ + +#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */ +#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */ +#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */ + +#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */ +#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24) +#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F) + +#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */ +#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22) +#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03) + +#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */ +#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */ +#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */ + +#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */ +#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */ +#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */ + +#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */ +#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4) +#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF) + +#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */ +#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */ +#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /*All Chip Select Gating Enable*/ +#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */ #endif /*----------------------------------------------------------------------------- @@ -534,16 +596,16 @@ #define CNTRL_DCR_BASE 0x0b0 #endif -#define CPC0_SYS0 (CNTRL_DCR_BASE+0x30) /* System configuration reg 0 */ -#define CPC0_SYS1 (CNTRL_DCR_BASE+0x31) /* System configuration reg 1 */ +#define CPC0_SYS0 (CNTRL_DCR_BASE+0x30) /* System configuration reg 0 */ +#define CPC0_SYS1 (CNTRL_DCR_BASE+0x31) /* System configuration reg 1 */ -#define CPC0_STRP0 (CNTRL_DCR_BASE+0x34) /* Power-on config reg 0 (RO) */ -#define CPC0_STRP1 (CNTRL_DCR_BASE+0x35) /* Power-on config reg 1 (RO) */ +#define CPC0_STRP0 (CNTRL_DCR_BASE+0x34) /* Power-on config reg 0 (RO) */ +#define CPC0_STRP1 (CNTRL_DCR_BASE+0x35) /* Power-on config reg 1 (RO) */ -#define CPC0_GPIO (CNTRL_DCR_BASE+0x38) /* GPIO config reg (440GP) */ +#define CPC0_GPIO (CNTRL_DCR_BASE+0x38) /* GPIO config reg (440GP) */ -#define CPC0_CR0 (CNTRL_DCR_BASE+0x3b) /* Control 0 register */ -#define CPC0_CR1 (CNTRL_DCR_BASE+0x3a) /* Control 1 register */ +#define CPC0_CR0 (CNTRL_DCR_BASE+0x3b) /* Control 0 register */ +#define CPC0_CR1 (CNTRL_DCR_BASE+0x3a) /* Control 1 register */ /*----------------------------------------------------------------------------- | DMA @@ -572,12 +634,12 @@ #define MAL0_IER (MAL_DCR_BASE + 0x02) /* Interrupt enable */ #define MAL0_TXCASR (MAL_DCR_BASE + 0x04) /* TX Channel active (set) */ #define MAL0_TXCARR (MAL_DCR_BASE + 0x05) /* TX Channel active (reset) */ -#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status */ +#define MAL0_TXEOBISR (MAL_DCR_BASE + 0x06) /* TX End of buffer int status*/ #define MAL0_TXDEIR (MAL_DCR_BASE + 0x07) /* TX Descr. Error Int */ #define MAL0_TXBADDR (MAL_DCR_BASE + 0x09) /* TX descriptor base addr*/ #define MAL0_RXCASR (MAL_DCR_BASE + 0x10) /* RX Channel active (set) */ #define MAL0_RXCARR (MAL_DCR_BASE + 0x11) /* RX Channel active (reset) */ -#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status */ +#define MAL0_RXEOBISR (MAL_DCR_BASE + 0x12) /* RX End of buffer int status*/ #define MAL0_RXDEIR (MAL_DCR_BASE + 0x13) /* RX Descr. Error Int */ #define MAL0_RXBADDR (MAL_DCR_BASE + 0x15) /* RX descriptor base addr */ #define MAL0_TXCTP0R (MAL_DCR_BASE + 0x20) /* TX 0 Channel table pointer */ @@ -658,7 +720,7 @@ #define SDR0_SDSTP0_TUNE_DECODE(n) ((((unsigned long)(n))>>17)&0x3FF) #define SDR0_SDSTP0_FBDV_MASK 0x0001F000 #define SDR0_SDSTP0_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12) -#define SDR0_SDSTP0_FBDV_DECODE(n) ((((((unsigned long)(n))>>12)-1)&0x1F)+1) +#define SDR0_SDSTP0_FBDV_DECODE(n) ((((((unsigned long)(n))>>12)-1)&0x1F)+1) #define SDR0_SDSTP0_FWDVA_MASK 0x00000F00 #define SDR0_SDSTP0_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<8) #define SDR0_SDSTP0_FWDVA_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x0F)+1) @@ -732,8 +794,8 @@ #define SDR0_SDSTP1_DBGEN_MASK 0x00000030 /* $218C */ #define SDR0_SDSTP1_DBGEN_FUNC 0x00000000 #define SDR0_SDSTP1_DBGEN_TRACE 0x00000010 -#define SDR0_SDSTP1_DBGEN_ENCODE(n) ((((unsigned long)(n))&0x03)<<4) /* $218C */ -#define SDR0_SDSTP1_DBGEN_DECODE(n) ((((unsigned long)(n))>>4)&0x03) /* $218C */ +#define SDR0_SDSTP1_DBGEN_ENCODE(n) ((((unsigned long)(n))&0x03)<<4) /* $218C */ +#define SDR0_SDSTP1_DBGEN_DECODE(n) ((((unsigned long)(n))>>4)&0x03) /* $218C */ #define SDR0_SDSTP1_ETH_MASK 0x00000004 #define SDR0_SDSTP1_ETH_10_100 0x00000000 #define SDR0_SDSTP1_ETH_GIGA 0x00000004 @@ -816,10 +878,14 @@ #define SDR0_PINSTP 0x0040 #define SDR0_PINSTP_BOOTSTRAP_MASK 0xC0000000 /* Strap Bits */ -#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 (EBC boot) */ -#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1 (PCI boot) */ -#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled - Addr = 0x54 */ -#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled - Addr = 0x50 */ +#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 + (EBC boot) */ +#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1 + (PCI boot) */ +#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled - + Addr = 0x54 */ +#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled - + Addr = 0x50 */ #define SDR0_SDCS 0x0060 #define SDR0_ECID0 0x0080 #define SDR0_ECID1 0x0081 @@ -960,8 +1026,10 @@ #define SDR0_PFC1_CPU_TRACE_MASK 0x00180000 /* $218C */ #define SDR0_PFC1_CPU_NO_TRACE 0x00000000 #define SDR0_PFC1_CPU_TRACE 0x00080000 -#define SDR0_PFC1_CPU_TRACE_ENCODE(n) ((((unsigned long)(n))&0x3)<<19) /* $218C */ -#define SDR0_PFC1_CPU_TRACE_DECODE(n) ((((unsigned long)(n))>>19)&0x03) /* $218C */ +#define SDR0_PFC1_CPU_TRACE_ENCODE(n) ((((unsigned long)(n))&0x3)<<19) + /* $218C */ +#define SDR0_PFC1_CPU_TRACE_DECODE(n) ((((unsigned long)(n))>>19)&0x03) + /* $218C */ #define SDR0_MFR 0x4300 #endif /* CONFIG_440SPE */ @@ -1023,34 +1091,43 @@ /* Ethernet Configuration Register (SDR0_ETH_CFG) */ #define SDR0_ETH_CFG 0x4103 -#define SDR0_ETH_CFG_SGMII3_LPBK 0x00800000 /* SGMII3 port loopback enable */ -#define SDR0_ETH_CFG_SGMII2_LPBK 0x00400000 /* SGMII2 port loopback enable */ -#define SDR0_ETH_CFG_SGMII1_LPBK 0x00200000 /* SGMII1 port loopback enable */ -#define SDR0_ETH_CFG_SGMII0_LPBK 0x00100000 /* SGMII0 port loopback enable */ -#define SDR0_ETH_CFG_SGMII_MASK 0x00070000 /* SGMII Mask */ -#define SDR0_ETH_CFG_SGMII2_ENABLE 0x00040000 /* SGMII2 port enable */ -#define SDR0_ETH_CFG_SGMII1_ENABLE 0x00020000 /* SGMII1 port enable */ -#define SDR0_ETH_CFG_SGMII0_ENABLE 0x00010000 /* SGMII0 port enable */ -#define SDR0_ETH_CFG_TAHOE1_BYPASS 0x00002000 /* TAHOE1 Bypass selector */ -#define SDR0_ETH_CFG_TAHOE0_BYPASS 0x00001000 /* TAHOE0 Bypass selector */ -#define SDR0_ETH_CFG_EMAC3_PHY_CLK_SEL 0x00000800 /* EMAC 3 PHY clock selector */ -#define SDR0_ETH_CFG_EMAC2_PHY_CLK_SEL 0x00000400 /* EMAC 2 PHY clock selector */ -#define SDR0_ETH_CFG_EMAC1_PHY_CLK_SEL 0x00000200 /* EMAC 1 PHY clock selector */ -#define SDR0_ETH_CFG_EMAC0_PHY_CLK_SEL 0x00000100 /* EMAC 0 PHY clock selector */ -#define SDR0_ETH_CFG_EMAC_2_1_SWAP 0x00000080 /* Swap EMAC2 with EMAC1 */ -#define SDR0_ETH_CFG_EMAC_0_3_SWAP 0x00000040 /* Swap EMAC0 with EMAC3 */ -#define SDR0_ETH_CFG_MDIO_SEL_MASK 0x00000030 /* MDIO source selector mask */ -#define SDR0_ETH_CFG_MDIO_SEL_EMAC0 0x00000000 /* MDIO source - EMAC0 */ -#define SDR0_ETH_CFG_MDIO_SEL_EMAC1 0x00000010 /* MDIO source - EMAC1 */ -#define SDR0_ETH_CFG_MDIO_SEL_EMAC2 0x00000020 /* MDIO source - EMAC2 */ -#define SDR0_ETH_CFG_MDIO_SEL_EMAC3 0x00000030 /* MDIO source - EMAC3 */ -#define SDR0_ETH_CFG_ZMII_MODE_MASK 0x0000000C /* ZMII bridge mode selector mask */ -#define SDR0_ETH_CFG_ZMII_SEL_MII 0x00000000 /* ZMII bridge mode - MII */ -#define SDR0_ETH_CFG_ZMII_SEL_SMII 0x00000004 /* ZMII bridge mode - SMII */ -#define SDR0_ETH_CFG_ZMII_SEL_RMII_10 0x00000008 /* ZMII bridge mode - RMII (10 Mbps) */ -#define SDR0_ETH_CFG_ZMII_SEL_RMII_100 0x0000000C /* ZMII bridge mode - RMII (100 Mbps) */ -#define SDR0_ETH_CFG_GMC1_BRIDGE_SEL 0x00000002 /* GMC Port 1 bridge selector */ -#define SDR0_ETH_CFG_GMC0_BRIDGE_SEL 0x00000001 /* GMC Port 0 bridge selector */ +#define SDR0_ETH_CFG_SGMII3_LPBK 0x00800000 /*SGMII3 port loopback + enable */ +#define SDR0_ETH_CFG_SGMII2_LPBK 0x00400000 /*SGMII2 port loopback + enable */ +#define SDR0_ETH_CFG_SGMII1_LPBK 0x00200000 /*SGMII1 port loopback + enable */ +#define SDR0_ETH_CFG_SGMII0_LPBK 0x00100000 /*SGMII0 port loopback + enable */ +#define SDR0_ETH_CFG_SGMII_MASK 0x00070000 /*SGMII Mask */ +#define SDR0_ETH_CFG_SGMII2_ENABLE 0x00040000 /*SGMII2 port enable */ +#define SDR0_ETH_CFG_SGMII1_ENABLE 0x00020000 /*SGMII1 port enable */ +#define SDR0_ETH_CFG_SGMII0_ENABLE 0x00010000 /*SGMII0 port enable */ +#define SDR0_ETH_CFG_TAHOE1_BYPASS 0x00002000 /*TAHOE1 Bypass selector */ +#define SDR0_ETH_CFG_TAHOE0_BYPASS 0x00001000 /*TAHOE0 Bypass selector */ +#define SDR0_ETH_CFG_EMAC3_PHY_CLK_SEL 0x00000800 /*EMAC 3 PHY clock selector*/ +#define SDR0_ETH_CFG_EMAC2_PHY_CLK_SEL 0x00000400 /*EMAC 2 PHY clock selector*/ +#define SDR0_ETH_CFG_EMAC1_PHY_CLK_SEL 0x00000200 /*EMAC 1 PHY clock selector*/ +#define SDR0_ETH_CFG_EMAC0_PHY_CLK_SEL 0x00000100 /*EMAC 0 PHY clock selector*/ +#define SDR0_ETH_CFG_EMAC_2_1_SWAP 0x00000080 /*Swap EMAC2 with EMAC1 */ +#define SDR0_ETH_CFG_EMAC_0_3_SWAP 0x00000040 /*Swap EMAC0 with EMAC3 */ +#define SDR0_ETH_CFG_MDIO_SEL_MASK 0x00000030 /*MDIO source selector mask*/ +#define SDR0_ETH_CFG_MDIO_SEL_EMAC0 0x00000000 /*MDIO source - EMAC0 */ +#define SDR0_ETH_CFG_MDIO_SEL_EMAC1 0x00000010 /*MDIO source - EMAC1 */ +#define SDR0_ETH_CFG_MDIO_SEL_EMAC2 0x00000020 /*MDIO source - EMAC2 */ +#define SDR0_ETH_CFG_MDIO_SEL_EMAC3 0x00000030 /*MDIO source - EMAC3 */ +#define SDR0_ETH_CFG_ZMII_MODE_MASK 0x0000000C /*ZMII bridge mode selector + mask */ +#define SDR0_ETH_CFG_ZMII_SEL_MII 0x00000000 /*ZMII bridge mode - MII */ +#define SDR0_ETH_CFG_ZMII_SEL_SMII 0x00000004 /*ZMII bridge mode - SMII */ +#define SDR0_ETH_CFG_ZMII_SEL_RMII_10 0x00000008 /*ZMII bridge mode - RMII + (10 Mbps) */ +#define SDR0_ETH_CFG_ZMII_SEL_RMII_100 0x0000000C /*ZMII bridge mode - RMII + (100 Mbps) */ +#define SDR0_ETH_CFG_GMC1_BRIDGE_SEL 0x00000002 /*GMC Port 1 bridge + selector */ +#define SDR0_ETH_CFG_GMC0_BRIDGE_SEL 0x00000001 /*GMC Port 0 bridge + selector */ #define SDR0_ETH_CFG_ZMII_MODE_SHIFT 4 #define SDR0_ETH_CFG_ZMII_MII_MODE 0x00 @@ -1063,26 +1140,46 @@ /* Miscealleneaous Function Reg. (SDR0_MFR) */ #define SDR0_MFR 0x4300 -#define SDR0_MFR_T0TxFL 0x00800000 /* force parity error TAHOE0 Tx FIFO bits 0:63 */ -#define SDR0_MFR_T0TxFH 0x00400000 /* force parity error TAHOE0 Tx FIFO bits 64:127 */ -#define SDR0_MFR_T1TxFL 0x00200000 /* force parity error TAHOE1 Tx FIFO bits 0:63 */ -#define SDR0_MFR_T1TxFH 0x00100000 /* force parity error TAHOE1 Tx FIFO bits 64:127 */ -#define SDR0_MFR_E0TxFL 0x00008000 /* force parity error EMAC0 Tx FIFO bits 0:63 */ -#define SDR0_MFR_E0TxFH 0x00004000 /* force parity error EMAC0 Tx FIFO bits 64:127 */ -#define SDR0_MFR_E0RxFL 0x00002000 /* force parity error EMAC0 Rx FIFO bits 0:63 */ -#define SDR0_MFR_E0RxFH 0x00001000 /* force parity error EMAC0 Rx FIFO bits 64:127 */ -#define SDR0_MFR_E1TxFL 0x00000800 /* force parity error EMAC1 Tx FIFO bits 0:63 */ -#define SDR0_MFR_E1TxFH 0x00000400 /* force parity error EMAC1 Tx FIFO bits 64:127 */ -#define SDR0_MFR_E1RxFL 0x00000200 /* force parity error EMAC1 Rx FIFO bits 0:63 */ -#define SDR0_MFR_E1RxFH 0x00000100 /* force parity error EMAC1 Rx FIFO bits 64:127 */ -#define SDR0_MFR_E2TxFL 0x00000080 /* force parity error EMAC2 Tx FIFO bits 0:63 */ -#define SDR0_MFR_E2TxFH 0x00000040 /* force parity error EMAC2 Tx FIFO bits 64:127 */ -#define SDR0_MFR_E2RxFL 0x00000020 /* force parity error EMAC2 Rx FIFO bits 0:63 */ -#define SDR0_MFR_E2RxFH 0x00000010 /* force parity error EMAC2 Rx FIFO bits 64:127 */ -#define SDR0_MFR_E3TxFL 0x00000008 /* force parity error EMAC3 Tx FIFO bits 0:63 */ -#define SDR0_MFR_E3TxFH 0x00000004 /* force parity error EMAC3 Tx FIFO bits 64:127 */ -#define SDR0_MFR_E3RxFL 0x00000002 /* force parity error EMAC3 Rx FIFO bits 0:63 */ -#define SDR0_MFR_E3RxFH 0x00000001 /* force parity error EMAC3 Rx FIFO bits 64:127 */ +#define SDR0_MFR_T0TxFL 0x00800000 /* force parity error TAHOE0 Tx + FIFO bits 0:63 */ +#define SDR0_MFR_T0TxFH 0x00400000 /* force parity error TAHOE0 Tx + FIFO bits 64:127 */ +#define SDR0_MFR_T1TxFL 0x00200000 /* force parity error TAHOE1 Tx + FIFO bits 0:63 */ +#define SDR0_MFR_T1TxFH 0x00100000 /* force parity error TAHOE1 Tx + FIFO bits 64:127 */ +#define SDR0_MFR_E0TxFL 0x00008000 /* force parity error EMAC0 Tx + FIFO bits 0:63 */ +#define SDR0_MFR_E0TxFH 0x00004000 /* force parity error EMAC0 Tx + FIFO bits 64:127 */ +#define SDR0_MFR_E0RxFL 0x00002000 /* force parity error EMAC0 Rx + FIFO bits 0:63 */ +#define SDR0_MFR_E0RxFH 0x00001000 /* force parity error EMAC0 Rx + FIFO bits 64:127 */ +#define SDR0_MFR_E1TxFL 0x00000800 /* force parity error EMAC1 Tx + FIFO bits 0:63 */ +#define SDR0_MFR_E1TxFH 0x00000400 /* force parity error EMAC1 Tx + FIFO bits 64:127 */ +#define SDR0_MFR_E1RxFL 0x00000200 /* force parity error EMAC1 Rx + FIFO bits 0:63 */ +#define SDR0_MFR_E1RxFH 0x00000100 /* force parity error EMAC1 Rx + FIFO bits 64:127 */ +#define SDR0_MFR_E2TxFL 0x00000080 /* force parity error EMAC2 Tx + FIFO bits 0:63 */ +#define SDR0_MFR_E2TxFH 0x00000040 /* force parity error EMAC2 Tx + FIFO bits 64:127 */ +#define SDR0_MFR_E2RxFL 0x00000020 /* force parity error EMAC2 Rx + FIFO bits 0:63 */ +#define SDR0_MFR_E2RxFH 0x00000010 /* force parity error EMAC2 Rx + FIFO bits 64:127 */ +#define SDR0_MFR_E3TxFL 0x00000008 /* force parity error EMAC3 Tx + FIFO bits 0:63 */ +#define SDR0_MFR_E3TxFH 0x00000004 /* force parity error EMAC3 Tx + FIFO bits 64:127 */ +#define SDR0_MFR_E3RxFL 0x00000002 /* force parity error EMAC3 Rx + FIFO bits 0:63 */ +#define SDR0_MFR_E3RxFH 0x00000001 /* force parity error EMAC3 Rx + FIFO bits 64:127 */ /* EMACx TX Status Register (SDR0_EMACxTXST)*/ #define SDR0_EMAC0TXST 0x4400 @@ -1090,30 +1187,30 @@ #define SDR0_EMAC2TXST 0x4402 #define SDR0_EMAC3TXST 0x4403 -#define SDR0_EMACxTXST_FUR 0x02000000 /* TX FIFO underrun */ -#define SDR0_EMACxTXST_BC 0x01000000 /* broadcase address */ -#define SDR0_EMACxTXST_MC 0x00800000 /* multicast address */ -#define SDR0_EMACxTXST_UC 0x00400000 /* unicast address */ -#define SDR0_EMACxTXST_FP 0x00200000 /* frame paused by control packet */ -#define SDR0_EMACxTXST_BFCS 0x00100000 /* bad FCS in the transmitted frame */ -#define SDR0_EMACxTXST_CPF 0x00080000 /* TX control pause frame */ -#define SDR0_EMACxTXST_CF 0x00040000 /* TX control frame */ -#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */ -#define SDR0_EMACxTXST_1023 0x00010000 /* 512-1023 bytes transmitted */ -#define SDR0_EMACxTXST_511 0x00008000 /* 256-511 bytes transmitted */ -#define SDR0_EMACxTXST_255 0x00004000 /* 128-255 bytes transmitted */ -#define SDR0_EMACxTXST_127 0x00002000 /* 65-127 bytes transmitted */ -#define SDR0_EMACxTXST_64 0x00001000 /* 64 bytes transmitted */ -#define SDR0_EMACxTXST_SQE 0x00000800 /* SQE indication */ -#define SDR0_EMACxTXST_LOC 0x00000400 /* loss of carrier sense */ -#define SDR0_EMACxTXST_IERR 0x00000080 /* EMAC internal error */ -#define SDR0_EMACxTXST_EDF 0x00000040 /* excessive deferral */ -#define SDR0_EMACxTXST_ECOL 0x00000020 /* excessive collisions */ -#define SDR0_EMACxTXST_LCOL 0x00000010 /* late collision */ -#define SDR0_EMACxTXST_DFFR 0x00000008 /* deferred frame */ -#define SDR0_EMACxTXST_MCOL 0x00000004 /* multiple collision frame */ -#define SDR0_EMACxTXST_SCOL 0x00000002 /* single collision frame */ -#define SDR0_EMACxTXST_TXOK 0x00000001 /* transmit OK */ +#define SDR0_EMACxTXST_FUR 0x02000000 /*TX FIFO underrun */ +#define SDR0_EMACxTXST_BC 0x01000000 /*broadcase address */ +#define SDR0_EMACxTXST_MC 0x00800000 /*multicast address */ +#define SDR0_EMACxTXST_UC 0x00400000 /*unicast address */ +#define SDR0_EMACxTXST_FP 0x00200000 /*frame paused by control packet */ +#define SDR0_EMACxTXST_BFCS 0x00100000 /*bad FCS in the transmitted frame */ +#define SDR0_EMACxTXST_CPF 0x00080000 /*TX control pause frame */ +#define SDR0_EMACxTXST_CF 0x00040000 /*TX control frame */ +#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */ +#define SDR0_EMACxTXST_1023 0x00010000 /*512-1023 bytes transmitted */ +#define SDR0_EMACxTXST_511 0x00008000 /*256-511 bytes transmitted */ +#define SDR0_EMACxTXST_255 0x00004000 /*128-255 bytes transmitted */ +#define SDR0_EMACxTXST_127 0x00002000 /*65-127 bytes transmitted */ +#define SDR0_EMACxTXST_64 0x00001000 /*64 bytes transmitted */ +#define SDR0_EMACxTXST_SQE 0x00000800 /*SQE indication */ +#define SDR0_EMACxTXST_LOC 0x00000400 /*loss of carrier sense */ +#define SDR0_EMACxTXST_IERR 0x00000080 /*EMAC internal error */ +#define SDR0_EMACxTXST_EDF 0x00000040 /*excessive deferral */ +#define SDR0_EMACxTXST_ECOL 0x00000020 /*excessive collisions */ +#define SDR0_EMACxTXST_LCOL 0x00000010 /*late collision */ +#define SDR0_EMACxTXST_DFFR 0x00000008 /*deferred frame */ +#define SDR0_EMACxTXST_MCOL 0x00000004 /*multiple collision frame */ +#define SDR0_EMACxTXST_SCOL 0x00000002 /*single collision frame */ +#define SDR0_EMACxTXST_TXOK 0x00000001 /*transmit OK */ /* EMACx RX Status Register (SDR0_EMACxRXST)*/ #define SDR0_EMAC0RXST 0x4404 @@ -1146,8 +1243,9 @@ #define SDR0_EMACxRXST_F2L 0x00000020 /* frame is to long */ #define SDR0_EMACxRXST_OERR 0x00000010 /* out of range length error */ #define SDR0_EMACxRXST_IERR 0x00000008 /* in range length error */ -#define SDR0_EMACxRXST_LOST 0x00000004 /* frame lost due to internal EMAC receive error */ -#define SDR0_EMACxRXST_BFCS 0x00000002 /* bad FCS in the recieved frame */ +#define SDR0_EMACxRXST_LOST 0x00000004 /* frame lost due to internal + EMAC receive error */ +#define SDR0_EMACxRXST_BFCS 0x00000002 /* bad FCS in the recieved frame */ #define SDR0_EMACxRXST_RXOK 0x00000001 /* Recieve OK */ /* EMACx TX Status Register (SDR0_EMACxREJCNT)*/ @@ -1300,23 +1398,24 @@ #define SDR0_MFR_ECS_MASK 0x10000000 #define SDR0_MFR_ECS_INTERNAL 0x10000000 -#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */ -#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */ -#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ -#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ -#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ -#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ -#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ -#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ -#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ -#define SDR0_MFR_ERRATA3_EN0 0x00800000 -#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ +#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs*/ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 #if defined(CONFIG_440GX) /* test-only: only 440GX or 440SPE??? */ -#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */ -#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 0-1 */ -#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */ -#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */ -#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */ +#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 + 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */ #endif @@ -1343,60 +1442,67 @@ #define SDR0_MFR_ECS_INTERNAL 0x10000000 #if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) -#define SDR0_SRST0 0x200 -#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */ -#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */ -#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */ -#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */ -#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/transmitter 0 */ -#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/transmitter 1 */ -#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */ -#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */ -#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */ -#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */ -#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */ -#define SDR0_SRST0_PCI 0x00100000 /* PCI */ -#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */ -#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */ -#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */ -#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */ -#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */ -#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */ -#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */ -#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */ -#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */ -#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */ -#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */ -#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */ -#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */ -#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */ -#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */ -#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */ -#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */ -#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/transmitter 2 */ -#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/transmitter 3 */ - -#define SDR0_SRST1 0x201 -#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */ -#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */ -#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */ +#define SDR0_SRST0 0x200 +#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */ +#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */ +#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */ +#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */ +#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/ + transmitter 0 */ +#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/ + transmitter 1 */ +#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */ +#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */ +#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */ +#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */ +#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */ +#define SDR0_SRST0_PCI 0x00100000 /* PCI */ +#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */ +#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */ +#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */ +#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */ +#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */ +#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */ +#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */ +#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */ +#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */ +#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */ +#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */ +#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */ +#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */ +#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */ +#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */ +#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */ +#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */ +#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/ + transmitter 2 */ +#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/ + transmitter 3 */ + +#define SDR0_SRST1 0x201 +#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */ +#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */ +#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */ #define SDR0_SRST1_PLB42OPB0 SDR0_SRST1_P4OPB0 -#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */ -#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */ -#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4 USB 2.0 Host */ -#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to USB 2.0 Host */ -#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to USB 2.0 Host */ -#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */ -#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2 */ -#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */ -#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */ -#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */ -#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */ -#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */ -#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */ -#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */ -#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */ -#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */ +#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */ +#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */ +#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4 + USB 2.0 Host */ +#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to + USB 2.0 Host */ +#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to + USB 2.0 Host */ +#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */ +#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2*/ +#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */ +#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */ +#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */ +#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */ +#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */ +#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */ +#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */ +#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */ +#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */ #define SDR0_EMAC0RXST 0x00004301 /* */ #define SDR0_EMAC0TXST 0x00004302 /* */ @@ -1411,8 +1517,10 @@ #define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */ #define SDR0_SRST0_EBC 0x20000000 /* External bus controller */ #define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */ -#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/transmitter 0 */ -#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/transmitter 1 */ +#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/ + transmitter 0 */ +#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/ + transmitter 1 */ #define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */ #define SDR0_SRST0_IIC1 0x01000000 /* Inter integrated circuit 1 */ #define SDR0_SRST0_GPIO0 0x00800000 /* General purpose I/O 0 */ @@ -1427,11 +1535,13 @@ #define SDR0_SRST0_UIC2 0x00001000 /* Universal interrupt controller 2*/ #define SDR0_SRST0_UIC3 0x00000800 /* Universal interrupt controller 3*/ #define SDR0_SRST0_OCM 0x00000400 /* Universal interrupt controller 0*/ -#define SDR0_SRST0_UART2 0x00000200 /* Universal asynchronous receiver/transmitter 2 */ +#define SDR0_SRST0_UART2 0x00000200 /* Universal asynchronous receiver/ + transmitter 2 */ #define SDR0_SRST0_MAL 0x00000100 /* Media access layer */ #define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */ #define SDR0_SRST0_L2CACHE 0x00000004 /* L2 Cache */ -#define SDR0_SRST0_UART3 0x00000002 /* Universal asynchronous receiver/transmitter 3 */ +#define SDR0_SRST0_UART3 0x00000002 /* Universal asynchronous receiver/ + transmitter 3 */ #define SDR0_SRST0_GPIO1 0x00000001 /* General purpose I/O 1 */ #define SDR0_SRST1 0x201 @@ -1440,17 +1550,22 @@ #define SDR0_SRST1_PLBARB 0x20000000 /* PLB Arbiter */ #define SDR0_SRST1_EIPPKP 0x10000000 /* EIPPPKP */ #define SDR0_SRST1_EIP94 0x08000000 /* EIP 94 */ -#define SDR0_SRST1_EMAC0 0x04000000 /* Ethernet media access controller 0 */ -#define SDR0_SRST1_EMAC1 0x02000000 /* Ethernet media access controller 1 */ -#define SDR0_SRST1_EMAC2 0x01000000 /* Ethernet media access controller 2 */ -#define SDR0_SRST1_EMAC3 0x00800000 /* Ethernet media access controller 3 */ +#define SDR0_SRST1_EMAC0 0x04000000 /* Ethernet media access + controller 0 */ +#define SDR0_SRST1_EMAC1 0x02000000 /* Ethernet media access + controller 1 */ +#define SDR0_SRST1_EMAC2 0x01000000 /* Ethernet media access + controller 2 */ +#define SDR0_SRST1_EMAC3 0x00800000 /* Ethernet media access + controller 3 */ #define SDR0_SRST1_ZMII 0x00400000 /* Ethernet ZMII/RMII/SMII */ #define SDR0_SRST1_RGMII0 0x00200000 /* Ethernet RGMII/RTBI 0 */ #define SDR0_SRST1_RGMII1 0x00100000 /* Ethernet RGMII/RTBI 1 */ #define SDR0_SRST1_DMA4 0x00080000 /* DMA to PLB4 */ #define SDR0_SRST1_DMA4CH 0x00040000 /* DMA Channel to PLB4 */ #define SDR0_SRST1_SATAPHY 0x00020000 /* Serial ATA PHY */ -#define SDR0_SRST1_SRIODEV 0x00010000 /* Serial Rapid IO core, PCS, and serdes */ +#define SDR0_SRST1_SRIODEV 0x00010000 /* Serial Rapid IO core, PCS, and + serdes */ #define SDR0_SRST1_SRIOPCS 0x00008000 /* Serial Rapid IO core and PCS */ #define SDR0_SRST1_NDFC 0x00004000 /* Nand flash controller */ #define SDR0_SRST1_SRIOPLB 0x00002000 /* Serial Rapid IO PLB */ @@ -1539,7 +1654,7 @@ #else /* !CONFIG_440GX or CONFIG_440EP or CONFIG_440GR */ #define PLLSYS0_ENG_MASK 0x80000000 /* 0 = SysClk, 1 = PLL VCO */ #define PLLSYS0_SRC_MASK 0x40000000 /* 0 = PLL A, 1 = PLL B */ -#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */ +#define PLLSYS0_SEL_MASK 0x38000000 /* 0 = PLL, 1 = CPU, 5 = PerClk */ #define PLLSYS0_TUNE_MASK 0x07fe0000 /* PLL Tune bits */ #define PLLSYS0_FB_DIV_MASK 0x0001f000 /* Feedback divisor */ #define PLLSYS0_FWD_DIV_A_MASK 0x00000f00 /* Fwd Div A */ @@ -1547,7 +1662,7 @@ #define PLLSYS0_PRI_DIV_B_MASK 0x0000001c /* PLL Primary Divisor B */ #define PLLSYS0_OPB_DIV_MASK 0x00000003 /* OPB Divisor */ -#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */ +#define PLLC_ENG_MASK 0x20000000 /* PLL primary forward divisor source */ #define PLLC_SRC_MASK 0x20000000 /* PLL feedback source */ #define PLLD_FBDV_MASK 0x1f000000 /* PLL Feedback Divisor */ #define PLLD_FWDVA_MASK 0x000f0000 /* PLL Forward Divisor A */ @@ -1624,27 +1739,30 @@ /* PCI Local Configuration Registers --------------------------------- */ -#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real => 0x0EF400000 */ +#define PCI_MMIO_LCR_BASE (CONFIG_SYS_PCI_BASE + 0x0f400000) /* Real => + 0x0EF400000 */ /* PCI Master Local Configuration Registers */ -#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */ -#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */ -#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */ -#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */ -#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */ -#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */ -#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */ -#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */ -#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */ -#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */ -#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */ -#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */ +#define PCIL0_PMM0LA (PCI_MMIO_LCR_BASE + 0x00) /* PMM0 Local Address */ +#define PCIL0_PMM0MA (PCI_MMIO_LCR_BASE + 0x04) /* PMM0 Mask/Attribute */ +#define PCIL0_PMM0PCILA (PCI_MMIO_LCR_BASE + 0x08) /* PMM0 PCI Low Address */ +#define PCIL0_PMM0PCIHA (PCI_MMIO_LCR_BASE + 0x0C) /* PMM0 PCI High Address */ +#define PCIL0_PMM1LA (PCI_MMIO_LCR_BASE + 0x10) /* PMM1 Local Address */ +#define PCIL0_PMM1MA (PCI_MMIO_LCR_BASE + 0x14) /* PMM1 Mask/Attribute */ +#define PCIL0_PMM1PCILA (PCI_MMIO_LCR_BASE + 0x18) /* PMM1 PCI Low Address */ +#define PCIL0_PMM1PCIHA (PCI_MMIO_LCR_BASE + 0x1C) /* PMM1 PCI High Address */ +#define PCIL0_PMM2LA (PCI_MMIO_LCR_BASE + 0x20) /* PMM2 Local Address */ +#define PCIL0_PMM2MA (PCI_MMIO_LCR_BASE + 0x24) /* PMM2 Mask/Attribute */ +#define PCIL0_PMM2PCILA (PCI_MMIO_LCR_BASE + 0x28) /* PMM2 PCI Low Address */ +#define PCIL0_PMM2PCIHA (PCI_MMIO_LCR_BASE + 0x2C) /* PMM2 PCI High Address */ /* PCI Target Local Configuration Registers */ -#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/Attribute */ -#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */ -#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/Attribute */ -#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */ +#define PCIL0_PTM1MS (PCI_MMIO_LCR_BASE + 0x30) /* PTM1 Memory Size/ + Attribute */ +#define PCIL0_PTM1LA (PCI_MMIO_LCR_BASE + 0x34) /* PTM1 Local Addr. Reg */ +#define PCIL0_PTM2MS (PCI_MMIO_LCR_BASE + 0x38) /* PTM2 Memory Size/ + Attribute */ +#define PCIL0_PTM2LA (PCI_MMIO_LCR_BASE + 0x3C) /* PTM2 Local Addr. Reg */ #else @@ -1674,6 +1792,31 @@ #define PCIL0_RES2 (PCIL0_CFGBASE + 0x0038 ) #define PCIL0_INTLN (PCIL0_CFGBASE + PCI_INTERRUPT_LINE ) #define PCIL0_INTPN (PCIL0_CFGBASE + PCI_INTERRUPT_PIN ) +#define SDR0_EMACxTXST_FUR 0x02000000 /* TX FIFO underrun */ +#define SDR0_EMACxTXST_BC 0x01000000 /* broadcase address */ +#define SDR0_EMACxTXST_MC 0x00800000 /* multicast address */ +#define SDR0_EMACxTXST_UC 0x00400000 /* unicast address */ +#define SDR0_EMACxTXST_FP 0x00200000 /* frame paused by control packet */ +#define SDR0_EMACxTXST_BFCS 0x00100000 /* bad FCS in the transmitted frame*/ +#define SDR0_EMACxTXST_CPF 0x00080000 /* TX control pause frame */ +#define SDR0_EMACxTXST_CF 0x00040000 /* TX control frame */ +#define SDR0_EMACxTXST_MSIZ 0x00020000 /* 1024-maxsize bytes transmitted */ +#define SDR0_EMACxTXST_1023 0x00010000 /* 512-1023 bytes transmitted */ +#define SDR0_EMACxTXST_511 0x00008000 /* 256-511 bytes transmitted */ +#define SDR0_EMACxTXST_255 0x00004000 /* 128-255 bytes transmitted */ +#define SDR0_EMACxTXST_127 0x00002000 /* 65-127 bytes transmitted */ +#define SDR0_EMACxTXST_64 0x00001000 /* 64 bytes transmitted */ +#define SDR0_EMACxTXST_SQE 0x00000800 /* SQE indication */ +#define SDR0_EMACxTXST_LOC 0x00000400 /* loss of carrier sense */ +#define SDR0_EMACxTXST_IERR 0x00000080 /* EMAC internal error */ +#define SDR0_EMACxTXST_EDF 0x00000040 /* excessive deferral */ +#define SDR0_EMACxTXST_ECOL 0x00000020 /* excessive collisions */ +#define SDR0_EMACxTXST_LCOL 0x00000010 /* late collision */ +#define SDR0_EMACxTXST_DFFR 0x00000008 /* deferred frame */ +#define SDR0_EMACxTXST_MCOL 0x00000004 /* multiple collision frame */ +#define SDR0_EMACxTXST_SCOL 0x00000002 /* single collision frame */ +#define SDR0_EMACxTXST_TXOK 0x00000001 /* transmit OK */ + #define PCIL0_MINGNT (PCIL0_CFGBASE + PCI_MIN_GNT ) #define PCIL0_MAXLTNCY (PCIL0_CFGBASE + PCI_MAX_LAT ) @@ -1713,24 +1856,41 @@ #define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) -#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for Endpoint 0 plus IN Endpoints 1 to 3 */ -#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management register */ -#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address register */ -#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRIN */ -#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for OUT Endpoints 1 to 3 */ -#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRUSB */ -#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for common USB interrupts */ -#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for IntrOut */ -#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0 test modes */ -#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for selecting the Endpoint status/control registers */ +#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for + Endpoint 0 plus IN Endpoints 1 to 3 */ +#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management + register */ +#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address + register */ +#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable + register for USB2D0_INTRIN */ +#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for + OUT Endpoints 1 to 3 */ +#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable + register for USB2D0_INTRUSB */ +#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for + common USB interrupts */ +#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable + register for IntrOut */ +#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0 + test modes */ +#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for + selecting the Endpoint status/control registers */ #define USB2D0_FRAME (USB2D0_BASE + 0x00000000) /* Frame number */ -#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status register for Endpoint 0. (Index register set to select Endpoint 0) */ -#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status register for IN Endpoint. (Index register set to select Endpoints 13) */ -#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for IN Endpoint. (Index register set to select Endpoints 13) */ -#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status register for OUT Endpoint. (Index register set to select Endpoints 13) */ -#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for OUT Endpoint. (Index register set to select Endpoints 13) */ -#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */ -#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in OUT Endpoint FIFO. (Index register set to select Endpoints 13) */ +#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status + register for Endpoint 0. (Index register set to select Endpoint 0) */ +#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status + register for IN Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet + size for IN Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status + register for OUT Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet + size for OUT Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received + bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */ +#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in + OUT Endpoint FIFO. (Index register set to select Endpoints 13) */ #endif /****************************************************************************** @@ -1739,55 +1899,55 @@ #if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ defined(CONFIG_460SX) -#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000700) +#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000700) -#define GPIO0_OR (GPIO0_BASE+0x0) -#define GPIO0_TCR (GPIO0_BASE+0x4) -#define GPIO0_ODR (GPIO0_BASE+0x18) -#define GPIO0_IR (GPIO0_BASE+0x1C) +#define GPIO0_OR (GPIO0_BASE+0x0) +#define GPIO0_TCR (GPIO0_BASE+0x4) +#define GPIO0_ODR (GPIO0_BASE+0x18) +#define GPIO0_IR (GPIO0_BASE+0x1C) #endif /* CONFIG_440GP */ #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000B00) -#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000C00) - -#define GPIO0_OR (GPIO0_BASE+0x0) -#define GPIO0_TCR (GPIO0_BASE+0x4) -#define GPIO0_OSRL (GPIO0_BASE+0x8) -#define GPIO0_OSRH (GPIO0_BASE+0xC) -#define GPIO0_TSRL (GPIO0_BASE+0x10) -#define GPIO0_TSRH (GPIO0_BASE+0x14) -#define GPIO0_ODR (GPIO0_BASE+0x18) -#define GPIO0_IR (GPIO0_BASE+0x1C) -#define GPIO0_RR1 (GPIO0_BASE+0x20) -#define GPIO0_RR2 (GPIO0_BASE+0x24) -#define GPIO0_RR3 (GPIO0_BASE+0x28) -#define GPIO0_ISR1L (GPIO0_BASE+0x30) -#define GPIO0_ISR1H (GPIO0_BASE+0x34) -#define GPIO0_ISR2L (GPIO0_BASE+0x38) -#define GPIO0_ISR2H (GPIO0_BASE+0x3C) -#define GPIO0_ISR3L (GPIO0_BASE+0x40) -#define GPIO0_ISR3H (GPIO0_BASE+0x44) - -#define GPIO1_OR (GPIO1_BASE+0x0) -#define GPIO1_TCR (GPIO1_BASE+0x4) -#define GPIO1_OSRL (GPIO1_BASE+0x8) -#define GPIO1_OSRH (GPIO1_BASE+0xC) -#define GPIO1_TSRL (GPIO1_BASE+0x10) -#define GPIO1_TSRH (GPIO1_BASE+0x14) -#define GPIO1_ODR (GPIO1_BASE+0x18) -#define GPIO1_IR (GPIO1_BASE+0x1C) -#define GPIO1_RR1 (GPIO1_BASE+0x20) -#define GPIO1_RR2 (GPIO1_BASE+0x24) -#define GPIO1_RR3 (GPIO1_BASE+0x28) -#define GPIO1_ISR1L (GPIO1_BASE+0x30) -#define GPIO1_ISR1H (GPIO1_BASE+0x34) -#define GPIO1_ISR2L (GPIO1_BASE+0x38) -#define GPIO1_ISR2H (GPIO1_BASE+0x3C) -#define GPIO1_ISR3L (GPIO1_BASE+0x40) -#define GPIO1_ISR3H (GPIO1_BASE+0x44) +#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000B00) +#define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE+0x00000C00) + +#define GPIO0_OR (GPIO0_BASE+0x0) +#define GPIO0_TCR (GPIO0_BASE+0x4) +#define GPIO0_OSRL (GPIO0_BASE+0x8) +#define GPIO0_OSRH (GPIO0_BASE+0xC) +#define GPIO0_TSRL (GPIO0_BASE+0x10) +#define GPIO0_TSRH (GPIO0_BASE+0x14) +#define GPIO0_ODR (GPIO0_BASE+0x18) +#define GPIO0_IR (GPIO0_BASE+0x1C) +#define GPIO0_RR1 (GPIO0_BASE+0x20) +#define GPIO0_RR2 (GPIO0_BASE+0x24) +#define GPIO0_RR3 (GPIO0_BASE+0x28) +#define GPIO0_ISR1L (GPIO0_BASE+0x30) +#define GPIO0_ISR1H (GPIO0_BASE+0x34) +#define GPIO0_ISR2L (GPIO0_BASE+0x38) +#define GPIO0_ISR2H (GPIO0_BASE+0x3C) +#define GPIO0_ISR3L (GPIO0_BASE+0x40) +#define GPIO0_ISR3H (GPIO0_BASE+0x44) + +#define GPIO1_OR (GPIO1_BASE+0x0) +#define GPIO1_TCR (GPIO1_BASE+0x4) +#define GPIO1_OSRL (GPIO1_BASE+0x8) +#define GPIO1_OSRH (GPIO1_BASE+0xC) +#define GPIO1_TSRL (GPIO1_BASE+0x10) +#define GPIO1_TSRH (GPIO1_BASE+0x14) +#define GPIO1_ODR (GPIO1_BASE+0x18) +#define GPIO1_IR (GPIO1_BASE+0x1C) +#define GPIO1_RR1 (GPIO1_BASE+0x20) +#define GPIO1_RR2 (GPIO1_BASE+0x24) +#define GPIO1_RR3 (GPIO1_BASE+0x28) +#define GPIO1_ISR1L (GPIO1_BASE+0x30) +#define GPIO1_ISR1H (GPIO1_BASE+0x34) +#define GPIO1_ISR2L (GPIO1_BASE+0x38) +#define GPIO1_ISR2H (GPIO1_BASE+0x3C) +#define GPIO1_ISR3L (GPIO1_BASE+0x40) +#define GPIO1_ISR3H (GPIO1_BASE+0x44) #endif #ifndef __ASSEMBLY__ diff --git a/include/ppc4xx.h b/include/ppc4xx.h index 086f8fb7ee..3bff00a559 100644 --- a/include/ppc4xx.h +++ b/include/ppc4xx.h @@ -136,12 +136,12 @@ * Common stuff for 4xx (405 and 440) */ -#define EXC_OFF_SYS_RESET 0x0100 /* System reset */ +#define EXC_OFF_SYS_RESET 0x0100 /* System reset */ #define _START_OFFSET (EXC_OFF_SYS_RESET + 0x2000) #define RESET_VECTOR 0xfffffffc -#define CACHELINE_MASK (CONFIG_SYS_CACHELINE_SIZE - 1) /* Address mask for cache - line aligned data. */ +#define CACHELINE_MASK (CONFIG_SYS_CACHELINE_SIZE - 1) /* Address mask for + cache line aligned data. */ #define CPR0_DCR_BASE 0x0C #define CPR0_CFGADDR (CPR0_DCR_BASE + 0x0) @@ -162,17 +162,25 @@ /* * Macros for indirect DCR access */ -#define mtcpr(reg, d) do { mtdcr(CPR0_CFGADDR,reg);mtdcr(CPR0_CFGDATA,d); } while (0) -#define mfcpr(reg, d) do { mtdcr(CPR0_CFGADDR,reg);d = mfdcr(CPR0_CFGDATA); } while (0) - -#define mtebc(reg, d) do { mtdcr(EBC0_CFGADDR,reg);mtdcr(EBC0_CFGDATA,d); } while (0) -#define mfebc(reg, d) do { mtdcr(EBC0_CFGADDR,reg);d = mfdcr(EBC0_CFGDATA); } while (0) - -#define mtsdram(reg, d) do { mtdcr(SDRAM0_CFGADDR,reg);mtdcr(SDRAM0_CFGDATA,d); } while (0) -#define mfsdram(reg, d) do { mtdcr(SDRAM0_CFGADDR,reg);d = mfdcr(SDRAM0_CFGDATA); } while (0) - -#define mtsdr(reg, d) do { mtdcr(SDR0_CFGADDR,reg);mtdcr(SDR0_CFGDATA,d); } while (0) -#define mfsdr(reg, d) do { mtdcr(SDR0_CFGADDR,reg);d = mfdcr(SDR0_CFGDATA); } while (0) +#define mtcpr(reg, d) \ + do { mtdcr(CPR0_CFGADDR, reg); mtdcr(CPR0_CFGDATA, d); } while (0) +#define mfcpr(reg, d) \ + do { mtdcr(CPR0_CFGADDR, reg); d = mfdcr(CPR0_CFGDATA); } while (0) + +#define mtebc(reg, d) \ + do { mtdcr(EBC0_CFGADDR, reg); mtdcr(EBC0_CFGDATA, d); } while (0) +#define mfebc(reg, d) \ + do { mtdcr(EBC0_CFGADDR, reg); d = mfdcr(EBC0_CFGDATA); } while (0) + +#define mtsdram(reg, d) \ + do { mtdcr(SDRAM0_CFGADDR, reg); mtdcr(SDRAM0_CFGDATA, d); } while (0) +#define mfsdram(reg, d) \ + do { mtdcr(SDRAM0_CFGADDR, reg); d = mfdcr(SDRAM0_CFGDATA); } while (0) + +#define mtsdr(reg, d) \ + do { mtdcr(SDR0_CFGADDR, reg); mtdcr(SDR0_CFGDATA, d); } while (0) +#define mfsdr(reg, d) \ + do { mtdcr(SDR0_CFGADDR, reg); d = mfdcr(SDR0_CFGDATA); } while (0) #ifndef __ASSEMBLY__ diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index 9be22e7d5a..3095aedc38 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -119,11 +119,11 @@ typedef struct emac_4xx_hw_st { int first_init; int tx_err_index; int rx_err_index; - int rx_slot; /* MAL Receive Slot */ - int rx_i_index; /* Receive Interrupt Queue Index */ - int rx_u_index; /* Receive User Queue Index */ - int tx_slot; /* MAL Transmit Slot */ - int tx_i_index; /* Transmit Interrupt Queue Index */ + int rx_slot; /* MAL Receive Slot */ + int rx_i_index; /* Receive Interrupt Queue Index */ + int rx_u_index; /* Receive User Queue Index */ + int tx_slot; /* MAL Transmit Slot */ + int tx_i_index; /* Transmit Interrupt Queue Index */ int tx_u_index; /* Transmit User Queue Index */ int rx_ready[NUM_RX_BUFF]; /* Receive Ready Queue */ int tx_run[NUM_TX_BUFF]; /* Transmit Running Queue */ @@ -262,16 +262,16 @@ typedef struct emac_4xx_hw_st { | TCP/IP Acceleration Hardware (TAH) 440GX Only +---------------------------------------------------------------------------*/ #if defined(CONFIG_440GX) -#define TAH_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x0B50) -#define TAH_REVID (TAH_BASE + 0x0) /* Revision ID (RO)*/ -#define TAH_MR (TAH_BASE + 0x10) /* Mode Register (R/W) */ -#define TAH_SSR0 (TAH_BASE + 0x14) /* Segment Size Reg 0 (R/W) */ -#define TAH_SSR1 (TAH_BASE + 0x18) /* Segment Size Reg 1 (R/W) */ -#define TAH_SSR2 (TAH_BASE + 0x1C) /* Segment Size Reg 2 (R/W) */ -#define TAH_SSR3 (TAH_BASE + 0x20) /* Segment Size Reg 3 (R/W) */ -#define TAH_SSR4 (TAH_BASE + 0x24) /* Segment Size Reg 4 (R/W) */ -#define TAH_SSR5 (TAH_BASE + 0x28) /* Segment Size Reg 5 (R/W) */ -#define TAH_TSR (TAH_BASE + 0x2C) /* Transmit Status Register (RO) */ +#define TAH_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x0B50) +#define TAH_REVID (TAH_BASE + 0x0) /* Revision ID (RO)*/ +#define TAH_MR (TAH_BASE + 0x10) /* Mode Register (R/W) */ +#define TAH_SSR0 (TAH_BASE + 0x14) /* Segment Size Reg 0 (R/W) */ +#define TAH_SSR1 (TAH_BASE + 0x18) /* Segment Size Reg 1 (R/W) */ +#define TAH_SSR2 (TAH_BASE + 0x1C) /* Segment Size Reg 2 (R/W) */ +#define TAH_SSR3 (TAH_BASE + 0x20) /* Segment Size Reg 3 (R/W) */ +#define TAH_SSR4 (TAH_BASE + 0x24) /* Segment Size Reg 4 (R/W) */ +#define TAH_SSR5 (TAH_BASE + 0x28) /* Segment Size Reg 5 (R/W) */ +#define TAH_TSR (TAH_BASE + 0x2C) /* Transmit Status Register (RO) */ /* TAH Revision */ #define TAH_REV_RN_M (0x000FFF00) /* Revision Number */ @@ -281,45 +281,45 @@ typedef struct emac_4xx_hw_st { #define TAH_REV_BN_V (0) /* TAH Mode Register */ -#define TAH_MR_CVR (0x80000000) /* Checksum verification on RX */ -#define TAH_MR_SR (0x40000000) /* Software reset */ -#define TAH_MR_ST (0x3F000000) /* Send Threshold */ -#define TAH_MR_TFS (0x00E00000) /* Transmit FIFO size */ -#define TAH_MR_DTFP (0x00100000) /* Disable TX FIFO parity */ -#define TAH_MR_DIG (0x00080000) /* Disable interrupt generation */ -#define TAH_MR_RSVD (0x0007FFFF) /* Reserved */ +#define TAH_MR_CVR (0x80000000) /* Checksum verification on RX */ +#define TAH_MR_SR (0x40000000) /* Software reset */ +#define TAH_MR_ST (0x3F000000) /* Send Threshold */ +#define TAH_MR_TFS (0x00E00000) /* Transmit FIFO size */ +#define TAH_MR_DTFP (0x00100000) /* Disable TX FIFO parity */ +#define TAH_MR_DIG (0x00080000) /* Disable interrupt generation */ +#define TAH_MR_RSVD (0x0007FFFF) /* Reserved */ -#define TAH_MR_ST_V (20) -#define TAH_MR_TFS_V (17) +#define TAH_MR_ST_V (20) +#define TAH_MR_TFS_V (17) -#define TAH_MR_TFS_2K (0x1) /* Transmit FIFO size 2Kbyte */ -#define TAH_MR_TFS_4K (0x2) /* Transmit FIFO size 4Kbyte */ -#define TAH_MR_TFS_6K (0x3) /* Transmit FIFO size 6Kbyte */ -#define TAH_MR_TFS_8K (0x4) /* Transmit FIFO size 8Kbyte */ -#define TAH_MR_TFS_10K (0x5) /* Transmit FIFO size 10Kbyte (max)*/ +#define TAH_MR_TFS_2K (0x1) /* Transmit FIFO size 2Kbyte */ +#define TAH_MR_TFS_4K (0x2) /* Transmit FIFO size 4Kbyte */ +#define TAH_MR_TFS_6K (0x3) /* Transmit FIFO size 6Kbyte */ +#define TAH_MR_TFS_8K (0x4) /* Transmit FIFO size 8Kbyte */ +#define TAH_MR_TFS_10K (0x5) /* Transmit FIFO size 10Kbyte (max)*/ /* TAH Segment Size Registers 0:5 */ -#define TAH_SSR_RSVD0 (0xC0000000) /* Reserved */ -#define TAH_SSR_SS (0x3FFE0000) /* Segment size in multiples of 2 */ -#define TAH_SSR_RSVD1 (0x0001FFFF) /* Reserved */ +#define TAH_SSR_RSVD0 (0xC0000000) /* Reserved */ +#define TAH_SSR_SS (0x3FFE0000) /* Segment size in multiples of 2 */ +#define TAH_SSR_RSVD1 (0x0001FFFF) /* Reserved */ /* TAH Transmit Status Register */ -#define TAH_TSR_TFTS (0x80000000) /* Transmit FIFO too small */ -#define TAH_TSR_UH (0x40000000) /* Unrecognized header */ -#define TAH_TSR_NIPF (0x20000000) /* Not IPv4 */ -#define TAH_TSR_IPOP (0x10000000) /* IP option present */ -#define TAH_TSR_NISF (0x08000000) /* No IEEE SNAP format */ -#define TAH_TSR_ILTS (0x04000000) /* IP length too short */ -#define TAH_TSR_IPFP (0x02000000) /* IP fragment present */ -#define TAH_TSR_UP (0x01000000) /* Unsupported protocol */ -#define TAH_TSR_TFP (0x00800000) /* TCP flags present */ -#define TAH_TSR_SUDP (0x00400000) /* Segmentation for UDP */ -#define TAH_TSR_DLM (0x00200000) /* Data length mismatch */ -#define TAH_TSR_SIEEE (0x00100000) /* Segmentation for IEEE */ -#define TAH_TSR_TFPE (0x00080000) /* Transmit FIFO parity error */ -#define TAH_TSR_SSTS (0x00040000) /* Segment size too small */ -#define TAH_TSR_RSVD (0x0003FFFF) /* Reserved */ +#define TAH_TSR_TFTS (0x80000000) /* Transmit FIFO too small */ +#define TAH_TSR_UH (0x40000000) /* Unrecognized header */ +#define TAH_TSR_NIPF (0x20000000) /* Not IPv4 */ +#define TAH_TSR_IPOP (0x10000000) /* IP option present */ +#define TAH_TSR_NISF (0x08000000) /* No IEEE SNAP format */ +#define TAH_TSR_ILTS (0x04000000) /* IP length too short */ +#define TAH_TSR_IPFP (0x02000000) /* IP fragment present */ +#define TAH_TSR_UP (0x01000000) /* Unsupported protocol */ +#define TAH_TSR_TFP (0x00800000) /* TCP flags present */ +#define TAH_TSR_SUDP (0x00400000) /* Segmentation for UDP */ +#define TAH_TSR_DLM (0x00200000) /* Data length mismatch */ +#define TAH_TSR_SIEEE (0x00100000) /* Segmentation for IEEE */ +#define TAH_TSR_TFPE (0x00080000) /* Transmit FIFO parity error */ +#define TAH_TSR_SSTS (0x00040000) /* Segment size too small */ +#define TAH_TSR_RSVD (0x0003FFFF) /* Reserved */ #endif /* CONFIG_440GX */