From: wdenk Date: Thu, 6 Mar 2003 00:58:30 +0000 (+0000) Subject: * Patch by Rune Torgersen, 13 Feb 2003: X-Git-Tag: LABEL_2006_03_12_0025~941 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=db2f721ffcf9693086a7e5c6c7015f2019e7f52e;p=oweals%2Fu-boot.git * Patch by Rune Torgersen, 13 Feb 2003: Add support for Motorola MPC8266ADS board * Patch by Kyle Harris, 19 Feb 2003: patches for the Intel lubbock board: memsetup.S - general cleanup (based on Robert's csb226 code) flash.c - overhaul, actually works now lubbock.c - fix init funcs to return proper value * Patch by Kenneth Johansson, 26 Feb 2003: - Fixed off by one in RFTA calculation. - No need to abort when LDF is lower than we can program it's only minimum timing so clamp it to what we can do. - Takes function pointer to function for reading the spd_nvram. Usefull for faking data or hardcode a module without the nvram. - fix other user for above change - fix some comments. * Patches by Brian Waite, 26 Feb 2003: - fix port for evb64260 board - fix PCI for evb64260 board - fix PCI scan * Patch by Reinhard Meyer, 1 Mar 2003: Add support for EMK TOP860 Module * Patch by Yuli Barcohen, 02 Mar 2003: Add SPD EEPROM support for MPC8260ADS board --- diff --git a/CHANGELOG b/CHANGELOG index 8457040d4b..8d6e2fa71c 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,35 @@ Changes since U-Boot 0.2.2: ====================================================================== +* Patch by Rune Torgersen, 13 Feb 2003: + Add support for Motorola MPC8266ADS board + +* Patch by Kyle Harris, 19 Feb 2003: + patches for the Intel lubbock board: + memsetup.S - general cleanup (based on Robert's csb226 code) + flash.c - overhaul, actually works now + lubbock.c - fix init funcs to return proper value + +* Patch by Kenneth Johansson, 26 Feb 2003: + - Fixed off by one in RFTA calculation. + - No need to abort when LDF is lower than we can program it's only + minimum timing so clamp it to what we can do. + - Takes function pointer to function for reading the spd_nvram. Usefull + for faking data or hardcode a module without the nvram. + - fix other user for above change + - fix some comments. + +* Patches by Brian Waite, 26 Feb 2003: + - fix port for evb64260 board + - fix PCI for evb64260 board + - fix PCI scan + +* Patch by Reinhard Meyer, 1 Mar 2003: + Add support for EMK TOP860 Module + +* Patch by Yuli Barcohen, 02 Mar 2003: + Add SPD EEPROM support for MPC8260ADS board + * Patch by Robert Schwebel, 21 Jan 2003: - Add support for Innokom board - Don't complain if "install" fails diff --git a/CREDITS b/CREDITS index 0b6353ae3e..77e609eda4 100644 --- a/CREDITS +++ b/CREDITS @@ -174,6 +174,10 @@ N: Dan Malek E: dan@netx4.com D: FADSROM, the grandfather of all of this +N: Reinhard Meyer +E: r.meyer@emk-elektronik.de +D: Port to EMK TOP860 Module + N: Jay Monkman E: jtm@smoothsmoothie.com D: EST SBC8260 support @@ -241,6 +245,10 @@ N: Jim Thompson E: jim@musenki.com D: Support for MUSENKI board +N: Rune Torgersen +E: +D: Support for Motorola MPC8266ADS board + N: David Updegraff E: dave@cray.com D: Port to Cray L1 board; DHCP vendor extensions diff --git a/MAINTAINERS b/MAINTAINERS index 1048ee105b..fee603a9c4 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -14,6 +14,7 @@ ######################################################################### +# PowerPC Systems: # # # # Maintainer Name, Email Address # # Board CPU # @@ -140,6 +141,10 @@ Eran Man EVB64260_750CX MPC750CX +Reinhard Meyer + + TOP860 MPC860 + Scott McNutt EBONY PPC440GP @@ -184,6 +189,10 @@ Jim Thompson MUSENKI MPC8245/8241 Sandpoint8245 MPC8245 +Rune Torgersen + + MPC8266ADS MPC8266 + ------------------------------------------------------------------------- Unknown / orphaned boards: diff --git a/MAKEALL b/MAKEALL index 75d934a506..8a4b1d484a 100644 --- a/MAKEALL +++ b/MAKEALL @@ -25,9 +25,9 @@ LIST_8xx=" \ MBX MBX860T MHPC MVS1 \ NETVIA NX823 pcu_e R360MPI \ RPXClassic RPXlite RRvision SM850 \ - SPD823TS SXNI855T TQM823L TQM823L_LCD \ - TQM850L TQM855L TQM860L TQM860L_FEC \ - TTTech v37 \ + SPD823TS SXNI855T TOP860 TQM823L \ + TQM823L_LCD TQM850L TQM855L TQM860L \ + TQM860L_FEC TTTech v37 \ " ######################################################################### @@ -59,9 +59,9 @@ LIST_824x=" \ LIST_8260=" \ cogent_mpc8260 CPU86 ep8260 gw8260 \ - hymod IPHASE4539 MPC8260ADS PM826 \ - ppmc8260 RPXsuper rsdproto sacsng \ - sbc8260 SCM TQM8260 \ + hymod IPHASE4539 MPC8260ADS MPC8266ADS \ + PM826 ppmc8260 RPXsuper rsdproto \ + sacsng sbc8260 SCM TQM8260 \ " ######################################################################### diff --git a/Makefile b/Makefile index 78babef40c..7ba2c436c2 100644 --- a/Makefile +++ b/Makefile @@ -329,6 +329,10 @@ SPD823TS_config: unconfig SXNI855T_config: unconfig @./mkconfig $(@:_config=) ppc mpc8xx sixnet +# EMK MPC8xx based modules +TOP860_config: unconfig + @./mkconfig $(@:_config=) ppc mpc8xx top860 emk + # Play some tricks for configuration selection # All boards can come with 50 MHz (default), 66MHz or 80MHz clock, # but only 855 and 860 boards may come with FEC @@ -516,6 +520,9 @@ IPHASE4539_config: unconfig MPC8260ADS_config: unconfig @./mkconfig $(@:_config=) ppc mpc8260 mpc8260ads +MPC8266ADS_config: unconfig + @./mkconfig $(@:_config=) ppc mpc8260 mpc8266ads + PM826_config \ PM826_ROMBOOT_config: unconfig @./mkconfig $(call xtract_82xx,$@) ppc mpc8260 pm826 diff --git a/board/ebony/ebony.c b/board/ebony/ebony.c index 723fad328c..b36d54224f 100644 --- a/board/ebony/ebony.c +++ b/board/ebony/ebony.c @@ -21,11 +21,10 @@ */ -extern long int spd_sdram (void); - #include #include "ebony.h" #include +#include #define BOOT_SMALL_FLASH 32 /* 00100000 */ #define FLASH_ONBD_N 2 /* 00000010 */ @@ -113,10 +112,9 @@ int checkboard (void) long int initdram (int board_type) { long dram_size = 0; - extern long spd_sdram (void); #if defined(CONFIG_SPD_EEPROM) - dram_size = spd_sdram (); + dram_size = spd_sdram (0); #else dram_size = fixed_sdram (); #endif diff --git a/board/emk/top860/Makefile b/board/emk/top860/Makefile new file mode 100644 index 0000000000..ef173d0366 --- /dev/null +++ b/board/emk/top860/Makefile @@ -0,0 +1,40 @@ +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS = $(BOARD).o flash.o + +$(LIB): .depend $(OBJS) + $(AR) crv $@ $^ + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +sinclude .depend + +######################################################################### diff --git a/board/emk/top860/flash.c b/board/emk/top860/flash.c new file mode 100644 index 0000000000..a9a9771144 --- /dev/null +++ b/board/emk/top860/flash.c @@ -0,0 +1,490 @@ +/* + * (C) Copyright 2003 + * EMK Elektronik GmbH + * Reinhard Meyer + * + * copied from the BMW Port - seems that its similiar enough + * to be easily adaped ;) --- Well, it turned out to become a + * merger between parts of the EMKstax Flash routines and the + * BMW funtion frames... + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#define FLASH_WORD_SIZE unsigned short +#define FLASH_WORD_WIDTH (sizeof (FLASH_WORD_SIZE)) + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/*----------------------------------------------------------------------- + * Functions + */ +static int write_word (flash_info_t *info, ulong dest, ulong data); + + +/***************************************************************************** + * software product ID entry/exit + *****************************************************************************/ +static void FlashProductIdMode ( + volatile FLASH_WORD_SIZE *b, + int on_off) +{ + b[0x5555] = 0xaa; + b[0x2aaa] = 0x55; + b[0x5555] = on_off ? 0x90 : 0xf0; +} + +/***************************************************************************** + * sector erase start + *****************************************************************************/ +static void FlashSectorErase ( + volatile FLASH_WORD_SIZE *b, + volatile FLASH_WORD_SIZE *a) +{ + b[0x5555] = 0xaa; + b[0x2aaa] = 0x55; + b[0x5555] = 0x80; + b[0x5555] = 0xaa; + b[0x2aaa] = 0x55; + a[0] = 0x30; +} + +/***************************************************************************** + * program a word + *****************************************************************************/ +static void FlashProgWord ( + volatile FLASH_WORD_SIZE *b, + volatile FLASH_WORD_SIZE *a, + FLASH_WORD_SIZE v) +{ + b[0x5555] = 0xaa; + b[0x2aaa] = 0x55; + b[0x5555] = 0xa0; + a[0] = v; +} + +/***************************************************************************** + * reset bank, back to read mode + *****************************************************************************/ +static void FlashReset (volatile FLASH_WORD_SIZE *b) +{ + b[0] = 0xf0; +} + +/***************************************************************************** + * identify FLASH chip + * this code is a stripped version of the FlashGetType() function in EMKstax + *****************************************************************************/ +unsigned long flash_init (void) +{ + volatile FLASH_WORD_SIZE * const flash = (volatile FLASH_WORD_SIZE *) CFG_FLASH_BASE; + FLASH_WORD_SIZE manu, dev; + flash_info_t * const pflinfo = &flash_info[0]; + int j; + + /* get Id Bytes */ + FlashProductIdMode (flash, 1); + manu = flash[0]; + dev = flash[1]; + FlashProductIdMode (flash, 0); + + pflinfo->size = 0; + pflinfo->sector_count = 0; + pflinfo->flash_id = 0xffffffff; + pflinfo->portwidth = FLASH_CFI_16BIT; + pflinfo->chipwidth = FLASH_CFI_BY16; + + switch (manu&0xff) + { + case 0x01: /* AMD */ + pflinfo->flash_id = FLASH_MAN_AMD; + switch (dev&0xff) + { + case 0x49: + pflinfo->size = 0x00200000; + pflinfo->sector_count = 35; + pflinfo->flash_id |= FLASH_AM160B; + pflinfo->start[0] = CFG_FLASH_BASE; + pflinfo->start[1] = CFG_FLASH_BASE + 0x4000; + pflinfo->start[2] = CFG_FLASH_BASE + 0x6000; + pflinfo->start[3] = CFG_FLASH_BASE + 0x8000; + for (j = 4; j < 35; j++) + { + pflinfo->start[j] = CFG_FLASH_BASE + 0x00010000 * (j-3); + } + break; + + case 0xf9: + pflinfo->size = 0x00400000; + pflinfo->sector_count = 71; + pflinfo->flash_id |= FLASH_AM320B; + pflinfo->start[0] = CFG_FLASH_BASE; + pflinfo->start[1] = CFG_FLASH_BASE + 0x4000; + pflinfo->start[2] = CFG_FLASH_BASE + 0x6000; + pflinfo->start[3] = CFG_FLASH_BASE + 0x8000; + for (j = 0; j < 8; j++) + { + pflinfo->start[j] = CFG_FLASH_BASE + 0x00002000 * (j); + } + for (j = 8; j < 71; j++) + { + pflinfo->start[j] = CFG_FLASH_BASE + 0x00010000 * (j-7); + } + break; + + default: + printf ("unknown AMD dev=%x ", dev); + pflinfo->flash_id |= FLASH_UNKNOWN; + } + break; + + default: + printf ("unknown manu=%x ", manu); + } + return pflinfo->size; +} + +/***************************************************************************** + * print info about a FLASH + *****************************************************************************/ +void flash_print_info (flash_info_t *info) +{ + static const char unk[] = "Unknown"; + unsigned int i; + const char *mfct=unk, + *type=unk; + + if(info->flash_id != FLASH_UNKNOWN) + { + switch (info->flash_id & FLASH_VENDMASK) + { + case FLASH_MAN_AMD: + mfct = "AMD"; + break; + } + + switch (info->flash_id & FLASH_TYPEMASK) + { + case FLASH_AM160B: + type = "AM29LV160B (16 Mbit, bottom boot sect)"; + break; + case FLASH_AM320B: + type = "AM29LV320B (32 Mbit, bottom boot sect)"; + break; + } + } + + printf ( + "\n Brand: %s Type: %s\n" + " Size: %lu KB in %d Sectors\n", + mfct, + type, + info->size >> 10, + info->sector_count + ); + + printf (" Sector Start Addresses:"); + + for (i = 0; i < info->sector_count; i++) + { + unsigned long size; + unsigned int erased; + unsigned long *flash = (unsigned long *) info->start[i]; + + /* + * Check if whole sector is erased + */ + size = + (i != (info->sector_count - 1)) ? + (info->start[i + 1] - info->start[i]) >> 2 : + (info->start[0] + info->size - info->start[i]) >> 2; + + for ( + flash = (unsigned long *) info->start[i], erased = 1; + (flash != (unsigned long *) info->start[i] + size) && erased; + flash++ + ) + erased = *flash == ~0x0UL; + + printf ( + "%s %08lX %s %s", + (i % 5) ? "" : "\n ", + info->start[i], + erased ? "E" : " ", + info->protect[i] ? "RO" : " " + ); + } + + puts ("\n"); + return; +} + +/***************************************************************************** + * erase one or more sectors + *****************************************************************************/ +int flash_erase (flash_info_t *info, int s_first, int s_last) +{ + volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *)(info->start[0]); + int flag, + prot, + sect, + l_sect; + ulong start, + now, + last; + + if ((s_first < 0) || (s_first > s_last)) + { + if (info->flash_id == FLASH_UNKNOWN) + { + printf ("- missing\n"); + } + else + { + printf ("- no sectors to erase\n"); + } + return 1; + } + + if ((info->flash_id == FLASH_UNKNOWN) || + (info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP))) + { + printf ("Can't erase unknown flash type - aborted\n"); + return 1; + } + + prot = 0; + for (sect=s_first; sect<=s_last; ++sect) + { + if (info->protect[sect]) + { + prot++; + } + } + + if (prot) + { + printf ("- Warning: %d protected sectors will not be erased!\n", + prot); + } + else + { + printf ("\n"); + } + + l_sect = -1; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect<=s_last; sect++) + { + if (info->protect[sect] == 0) + { /* not protected */ + FlashSectorErase ((FLASH_WORD_SIZE *)info->start[0], (FLASH_WORD_SIZE *)info->start[sect]); + l_sect = sect; + } + } + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* wait at least 80us - let's wait 1 ms */ + udelay (1000); + + /* + * We wait for the last triggered sector + */ + if (l_sect < 0) + goto DONE; + + start = get_timer (0); + last = start; + addr = (FLASH_WORD_SIZE *)info->start[l_sect]; + while ((addr[0] & 0x0080) != 0x0080) + { + if ((now = get_timer (start)) > CFG_FLASH_ERASE_TOUT) + { + printf ("Timeout\n"); + return 1; + } + /* show that we're waiting */ + if ((now - last) > 1000) + { /* every second */ + serial_putc ('.'); + last = now; + } + } + + DONE: + /* reset to read mode */ + FlashReset ((FLASH_WORD_SIZE *)info->start[0]); + + printf (" done\n"); + return 0; +} + +/***************************************************************************** + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + *****************************************************************************/ +int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) +{ + ulong cp, + wp, + data; + int i, + l, + rc; + + wp = (addr & ~(FLASH_WORD_WIDTH-1)); /* get lower word aligned address */ + + /* + * handle unaligned start bytes, if there are... + */ + if ((l = addr - wp) != 0) + { + data = 0; + + /* get the current before the new data into our data word */ + for (i=0, cp=wp; i0; ++i, ++cp, --cnt) + { + data = (data << 8) | *src++; + } + + /* get the current after the new data into our data word */ + for (; cnt==0 && i= FLASH_WORD_WIDTH) + { + data = 0; + for (i=0; i0; ++i, ++cp) + { + data = (data << 8) | *src++; + --cnt; + } + + /* get the current after the new data into our data word */ + for (; istart[0]; + volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *)dest; + FLASH_WORD_SIZE data2 = data; + ulong start; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ((*dest2 & data2) != data2) + { + return (2); + } + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + + FlashProgWord (addr2, dest2, data2); + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts (); + + /* data polling for D7 */ + start = get_timer (0); + while ((*dest2 & 0x0080) != (data2 & 0x0080)) + { + if (get_timer (start) > CFG_FLASH_WRITE_TOUT) + { + return (1); + } + } + + return (0); +} + +/*----------------------------------------------------------------------- + */ + diff --git a/board/emk/top860/top860.c b/board/emk/top860/top860.c new file mode 100644 index 0000000000..b99bf0e928 --- /dev/null +++ b/board/emk/top860/top860.c @@ -0,0 +1,187 @@ +/* + * (C) Copyright 2003 + * EMK Elektronik GmbH + * Reinhard Meyer + * + * Board specific routines for the TOP860 + * + * - initialisation + * - interface to VPD data (mac address, clock speeds) + * - memory controller + * - serial io initialisation + * - ethernet io initialisation + * + * ----------------------------------------------------------------- + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/***************************************************************************** + * UPM table for 60ns EDO RAM at 25 MHz bus/external clock + *****************************************************************************/ +static const uint edo_60ns_25MHz_tbl[] = { + +/* single read (offset 0x00 in upm ram) */ + 0x0ff3fc04,0x08f3fc04,0x00f3fc04,0x00f3fc00, + 0x33f7fc07,0xfffffc05,0xfffffc05,0xfffffc05, +/* burst read (offset 0x08 in upm ram) */ + 0x0ff3fc04,0x08f3fc04,0x00f3fc0c,0x0ff3fc40, + 0x0cf3fc04,0x03f3fc48,0x0cf3fc04,0x03f3fc48, + 0x0cf3fc04,0x03f3fc00,0x3ff7fc07,0xfffffc05, + 0xfffffc05,0xfffffc05,0xfffffc05,0xfffffc05, +/* single write (offset 0x18 in upm ram) */ + 0x0ffffc04,0x08fffc04,0x30fffc00,0xf1fffc07, + 0xfffffc05,0xfffffc05,0xfffffc05,0xfffffc05, +/* burst write (offset 0x20 in upm ram) */ + 0x0ffffc04,0x08fffc00,0x00fffc04,0x03fffc4c, + 0x00fffc00,0x07fffc4c,0x00fffc00,0x0ffffc4c, + 0x00fffc00,0x3ffffc07,0xfffffc05,0xfffffc05, + 0xfffffc05,0xfffffc05,0xfffffc05,0xfffffc05, +/* refresh (offset 0x30 in upm ram) */ + 0xc0fffc04,0x07fffc04,0x0ffffc04,0x0ffffc04, + 0xfffffc05,0xfffffc05,0xfffffc05,0xfffffc05, + 0xfffffc05,0xfffffc05,0xfffffc05,0xfffffc05, +/* exception (offset 0x3C in upm ram) */ + 0xfffffc07,0xfffffc03,0xfffffc05,0xfffffc05, +}; + +/***************************************************************************** + * Print Board Identity + *****************************************************************************/ +int checkboard (void) +{ + puts ("Board:"CONFIG_IDENT_STRING"\n"); + return (0); +} + +/***************************************************************************** + * Initialize DRAM controller + *****************************************************************************/ +long int initdram (int board_type) +{ + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + + /* + * Only initialize memory controller when running from FLASH. + * When running from RAM, don't touch it. + */ + if ((ulong) initdram & 0xff000000) + { + volatile uint *addr1, *addr2; + uint i, j; + + upmconfig (UPMA, (uint *) edo_60ns_25MHz_tbl, + sizeof (edo_60ns_25MHz_tbl) / sizeof (uint)); + memctl->memc_mptpr = 0x0200; + memctl->memc_mamr = 0x0ca20330; + memctl->memc_or2 = -CFG_DRAM_MAX | OR_CSNT_SAM; + memctl->memc_br2 = CFG_DRAM_BASE | BR_MS_UPMA | BR_V; + /* + * Do 8 read accesses to DRAM + */ + addr1 = (volatile uint*) 0; + addr2 = (volatile uint*) 0x00400000; + for (i=0, j=0; i<8; i++) + j = addr1[0]; + + /* + * Now check whether we got 4MB or 16MB populated + */ + addr1[0] = 0x12345678; + addr1[1] = 0x9abcdef0; + addr2[0] = 0xfeedc0de; + addr2[1] = 0x47110815; + if (addr1[0] == 0xfeedc0de && addr1[1] == 0x47110815) + { + /* only 4MB populated */ + memctl->memc_or2 = -(CFG_DRAM_MAX/4) | OR_CSNT_SAM; + } + } + + return -(memctl->memc_or2 & 0xffff0000); +} + +/***************************************************************************** + * otherinits after RAM is there and we are relocated to RAM + * note: though this is an int function, nobody cares for the result! + *****************************************************************************/ +int misc_init_r (void) +{ + /* read 'factory' part of EEPROM */ + uchar buf[81]; + uchar *p; + uint length; + uint addr; + uint len; + + /* get length first */ + addr = CFG_FACT_OFFSET; + if (eeprom_read (CFG_I2C_FACT_ADDR, addr, buf, 2)) + { +bailout: + printf ("cannot read factory configuration\n"); + printf ("be sure to set ethaddr yourself!\n"); + return 0; + } + length = buf[0] + (buf[1]<<8); + addr += 2; + + /* sanity check */ + if (length < 20 || length > CFG_FACT_SIZE-2) + goto bailout; + + /* read lines */ + while (length > 0) + { + /* read one line */ + len = length > 80 ? 80 : length; + if (eeprom_read (CFG_I2C_FACT_ADDR, addr, buf, len)) + goto bailout; + /* mark end of buffer */ + buf[len] = 0; + /* search end of line */ + for (p=buf; *p && *p != 0x0a; p++) ; + if (!*p) + goto bailout; + *p++ = 0; + /* advance to next line start */ + length -= p-buf; + addr += p-buf; + /*printf ("%s\n", buf);*/ + /* search for our specific entry */ + if (!strncmp ((char *)buf, "[RLA/lan/Ethernet] ", 19)) + { + setenv ("ethaddr", buf+19); + } + else if (!strncmp ((char *)buf, "[BOARD/SERIAL] ", 15)) + { + setenv ("serial#", buf+15); + } + else if (!strncmp ((char *)buf, "[BOARD/TYPE] ", 13)) + { + setenv ("board_id", buf+13); + } + } + return (0); +} + diff --git a/board/emk/top860/u-boot.lds b/board/emk/top860/u-boot.lds new file mode 100644 index 0000000000..d647be362a --- /dev/null +++ b/board/emk/top860/u-boot.lds @@ -0,0 +1,122 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc8xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} + diff --git a/board/emk/top860/u-boot.lds.debug b/board/emk/top860/u-boot.lds.debug new file mode 100644 index 0000000000..bd13b7b96f --- /dev/null +++ b/board/emk/top860/u-boot.lds.debug @@ -0,0 +1,132 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/mpc8xx/start.o (.text) + common/dlmalloc.o (.text) + lib_generic/vsprintf.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + + . = env_offset; + common/environment.o(.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} + diff --git a/board/evb64260/evb64260.c b/board/evb64260/evb64260.c index 1c02e321f4..02431dab55 100644 --- a/board/evb64260/evb64260.c +++ b/board/evb64260/evb64260.c @@ -315,8 +315,10 @@ int misc_init_r (void) } void -after_reloc(gd_t *gd, ulong dest_addr) +after_reloc(ulong dest_addr) { + DECLARE_GLOBAL_DATA_PTR; + /* check to see if we booted from the sram. If so, move things * back to the way they should be. (we're running from main * memory at this point now */ diff --git a/board/evb64260/pci.c b/board/evb64260/pci.c index 585906d31d..5f3b154d55 100644 --- a/board/evb64260/pci.c +++ b/board/evb64260/pci.c @@ -52,6 +52,7 @@ static const unsigned int pci_scs_bank_size[2][4] = { static const unsigned int pci_p2p_configuration[] = { PCI_0P2P_CONFIGURATION, PCI_1P2P_CONFIGURATION}; +static unsigned int local_buses[] = { 0, 0}; /******************************************************************** * pciWriteConfigReg - Write to a PCI configuration register * - Make sure the GT is configured as a master before writing @@ -74,7 +75,7 @@ void pciWriteConfigReg(PCI_HOST host, unsigned int regOffset,unsigned int pciDev { volatile unsigned int DataForAddrReg; unsigned int functionNum; - unsigned int busNum = 0; + unsigned int busNum = PCI_BUS(pciDevNum); unsigned int addr; if(pciDevNum > 32) /* illegal device Number */ @@ -117,7 +118,7 @@ unsigned int pciReadConfigReg (PCI_HOST host, unsigned int regOffset,unsigned in volatile unsigned int DataForAddrReg; unsigned int data; unsigned int functionNum; - unsigned int busNum = 0; + unsigned int busNum = PCI_BUS(pciDevNum); if(pciDevNum > 32) /* illegal device Number */ return 0xffffffff; @@ -531,16 +532,32 @@ static int gt_read_config_dword(struct pci_controller *hose, pci_dev_t dev, int offset, u32* value) { - *value = pciReadConfigReg((PCI_HOST) hose->cfg_addr, offset, PCI_DEV(dev)); - return 0; + int bus = PCI_BUS(dev); + + if ((bus == local_buses[0]) || (bus == local_buses[1])){ + *value = pciReadConfigReg((PCI_HOST) hose->cfg_addr, offset, + PCI_DEV(dev)); + } else { + *value = pciOverBridgeReadConfigReg((PCI_HOST) hose->cfg_addr, + offset, PCI_DEV(dev), bus); + } + return 0; } static int gt_write_config_dword(struct pci_controller *hose, pci_dev_t dev, int offset, u32 value) { - pciWriteConfigReg((PCI_HOST)hose->cfg_addr, offset, PCI_DEV(dev), value); - return 0; + int bus = PCI_BUS(dev); + + if ((bus == local_buses[0]) || (bus == local_buses[1])){ + pciWriteConfigReg((PCI_HOST)hose->cfg_addr, offset, + PCI_DEV(dev), value); + } else { + pciOverBridgeWriteConfigReg((PCI_HOST)hose->cfg_addr, offset, + PCI_DEV(dev), value, bus); + } + return 0; } /* @@ -603,7 +620,7 @@ pci_init_board(void) pci0_hose.first_busno = 0; pci0_hose.last_busno = 0xff; - + local_buses[0] = pci0_hose.first_busno; /* PCI memory space */ pci_set_region(pci0_hose.regions + 0, CFG_PCI0_0_MEM_SPACE, @@ -647,6 +664,8 @@ pci_init_board(void) pci1_hose.first_busno = pci0_hose.last_busno + 1; pci1_hose.last_busno = 0xff; + pci1_hose.current_busno = pci0_hose.current_busno; + local_buses[1] = pci1_hose.first_busno; /* PCI memory space */ pci_set_region(pci1_hose.regions + 0, diff --git a/board/lubbock/config.mk b/board/lubbock/config.mk index d6ec08cf1a..0ffe1ba639 100644 --- a/board/lubbock/config.mk +++ b/board/lubbock/config.mk @@ -1,12 +1,3 @@ -# -# Linux-Kernel is expected to be at c000'8000, entry c000'8000 -# -# we load ourself to c170'0000, the upper 1 MB of second bank -# -# download areas is c800'0000 -# - - #TEXT_BASE = 0xa1700000 TEXT_BASE = 0xa3000000 #TEXT_BASE = 0 diff --git a/board/lubbock/flash.c b/board/lubbock/flash.c index 84c09a853c..a93875083b 100644 --- a/board/lubbock/flash.c +++ b/board/lubbock/flash.c @@ -1,10 +1,9 @@ /* - * (C) Copyright 2002 + * (C) Copyright 2001 * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. @@ -26,46 +25,62 @@ */ #include +#include -#define FLASH_BANK_SIZE 0x2000000 -#define MAIN_SECT_SIZE 0x40000 /* 2x16 = 256k per sector */ -flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ +/* Board support for 1 or 2 flash devices */ +#define FLASH_PORT_WIDTH32 +#undef FLASH_PORT_WIDTH16 + +#ifdef FLASH_PORT_WIDTH16 +#define FLASH_PORT_WIDTH ushort +#define FLASH_PORT_WIDTHV vu_short +#define SWAP(x) __swab16(x) +#else +#define FLASH_PORT_WIDTH ulong +#define FLASH_PORT_WIDTHV vu_long +#define SWAP(x) __swab32(x) +#endif + +#define FPW FLASH_PORT_WIDTH +#define FPWV FLASH_PORT_WIDTHV + +#define mb() __asm__ __volatile__ ("" : : : "memory") /*----------------------------------------------------------------------- + * Functions */ +static ulong flash_get_size (FPW *addr, flash_info_t *info); +static int write_data (flash_info_t *info, ulong dest, FPW data); +static void flash_get_offsets (ulong base, flash_info_t *info); +void inline spin_wheel(void); -ulong flash_init(void) +/*----------------------------------------------------------------------- + */ + +unsigned long flash_init (void) { - int i, j; + int i; ulong size = 0; for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) { - ulong flashbase = 0; - flash_info[i].flash_id = - (INTEL_MANUFACT & FLASH_VENDMASK) | - (INTEL_ID_28F128J3 & FLASH_TYPEMASK); - flash_info[i].size = FLASH_BANK_SIZE; - flash_info[i].sector_count = CFG_MAX_FLASH_SECT; - memset(flash_info[i].protect, 0, CFG_MAX_FLASH_SECT); switch (i) { case 0: - flashbase = PHYS_FLASH_1; + flash_get_size((FPW *)PHYS_FLASH_1, &flash_info[i]); + flash_get_offsets(PHYS_FLASH_1, &flash_info[i]); break; case 1: - flashbase = PHYS_FLASH_2; + flash_get_size((FPW *)PHYS_FLASH_2, &flash_info[i]); + flash_get_offsets(PHYS_FLASH_2, &flash_info[i]); break; default: panic("configured to many flash banks!\n"); break; } - for (j = 0; j < flash_info[i].sector_count; j++) - { - flash_info[i].start[j] = flashbase + j*MAIN_SECT_SIZE; - } size += flash_info[i].size; } @@ -84,73 +99,142 @@ ulong flash_init(void) return size; } +/*----------------------------------------------------------------------- + */ +static void flash_get_offsets (ulong base, flash_info_t *info) +{ + int i; + + if (info->flash_id == FLASH_UNKNOWN) { + return; + } + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) { + for (i = 0; i < info->sector_count; i++) { + info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE); + info->protect[i] = 0; + } + } +} + /*----------------------------------------------------------------------- */ void flash_print_info (flash_info_t *info) { - int i, j; + int i; - for (j=0; jflash_id & FLASH_VENDMASK) - { - case (INTEL_MANUFACT & FLASH_VENDMASK): - printf("Intel: "); - break; - default: - printf("Unknown Vendor "); - break; + if (info->flash_id == FLASH_UNKNOWN) { + printf ("missing or unknown FLASH type\n"); + return; } - switch (info->flash_id & FLASH_TYPEMASK) - { - case (INTEL_ID_28F128J3 & FLASH_TYPEMASK): - printf("28F128J3 (128Mbit)\n"); - break; - default: - printf("Unknown Chip Type\n"); - goto Done; - break; + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_INTEL: printf ("INTEL "); break; + default: printf ("Unknown Vendor "); break; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_28F128J3A: + printf ("28F128J3A\n"); break; + default: printf ("Unknown Chip Type\n"); break; } - printf(" Size: %ld MB in %d Sectors\n", + printf (" Size: %ld MB in %d Sectors\n", info->size >> 20, info->sector_count); - printf(" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; i++) - { + printf (" Sector Start Addresses:"); + for (i=0; isector_count; ++i) { if ((i % 5) == 0) - { printf ("\n "); - } - printf (" %08lX%s", info->start[i], - info->protect[i] ? " (RO)" : " "); + printf (" %08lX%s", + info->start[i], + info->protect[i] ? " (RO)" : " " + ); } printf ("\n"); - info++; + return; +} + +/* + * The following code cannot be run from FLASH! + */ +static ulong flash_get_size (FPW *addr, flash_info_t *info) +{ + volatile FPW value; + + /* Write auto select command: read Manufacturer ID */ + addr[0x5555] = (FPW)0x00AA00AA; + addr[0x2AAA] = (FPW)0x00550055; + addr[0x5555] = (FPW)0x00900090; + + mb(); + value = addr[0]; + + switch (value) { + + case (FPW)INTEL_MANUFACT: + info->flash_id = FLASH_MAN_INTEL; + break; + + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + addr[0] = (FPW)0x00FF00FF; /* restore read mode */ + return (0); /* no or unknown flash */ + } + + mb(); + value = addr[1]; /* device ID */ + + switch (value) { + + case (FPW)INTEL_ID_28F128J3A: + info->flash_id += FLASH_28F128J3A; + info->sector_count = 128; + info->size = 0x02000000; + break; /* => 16 MB */ + + default: + info->flash_id = FLASH_UNKNOWN; + break; + } + + if (info->sector_count > CFG_MAX_FLASH_SECT) { + printf ("** ERROR: sector count %d > max (%d) **\n", + info->sector_count, CFG_MAX_FLASH_SECT); + info->sector_count = CFG_MAX_FLASH_SECT; } -Done: + addr[0] = (FPW)0x00FF00FF; /* restore read mode */ + + return (info->size); } + /*----------------------------------------------------------------------- */ int flash_erase (flash_info_t *info, int s_first, int s_last) { int flag, prot, sect; - int rc = ERR_OK; - - if (info->flash_id == FLASH_UNKNOWN) - return ERR_UNKNOWN_FLASH_TYPE; + ulong type, start, now, last; + int rcode = 0; if ((s_first < 0) || (s_first > s_last)) { - return ERR_INVAL; + if (info->flash_id == FLASH_UNKNOWN) { + printf ("- missing\n"); + } else { + printf ("- no sectors to erase\n"); + } + return 1; } - if ((info->flash_id & FLASH_VENDMASK) != - (INTEL_MANUFACT & FLASH_VENDMASK)) { - return ERR_UNKNOWN_FLASH_VENDOR; + type = (info->flash_id & FLASH_VENDMASK); + if ((type != FLASH_MAN_INTEL)) { + printf ("Can't erase unknown flash type %08lx - aborted\n", + info->flash_id); + return 1; } prot = 0; @@ -159,153 +243,79 @@ int flash_erase (flash_info_t *info, int s_first, int s_last) prot++; } } - if (prot) - return ERR_PROTECTED; - /* - * Disable interrupts which might cause a timeout - * here. Remember that our exception vectors are - * at address 0 in the flash, and we don't want a - * (ticker) exception to happen while the flash - * chip is in programming mode. - */ + if (prot) { + printf ("- Warning: %d protected sectors will not be erased!\n", + prot); + } else { + printf ("\n"); + } + + start = get_timer (0); + last = start; + + /* Disable interrupts which might cause a timeout here */ flag = disable_interrupts(); /* Start erase on unprotected sectors */ - for (sect = s_first; sect<=s_last && !ctrlc(); sect++) { + for (sect = s_first; sect<=s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + FPWV *addr = (FPWV *)(info->start[sect]); + FPW status; printf("Erasing sector %2d ... ", sect); /* arm simple, non interrupt dependent timer */ reset_timer_masked(); - if (info->protect[sect] == 0) { /* not protected */ - vu_short *addr = (vu_short *)(info->start[sect]); + *addr = (FPW)0x00500050; /* clear status register */ + *addr = (FPW)0x00200020; /* erase setup */ + *addr = (FPW)0x00D000D0; /* erase confirm */ - *addr = 0x20; /* erase setup */ - *addr = 0xD0; /* erase confirm */ - - while ((*addr & 0x80) != 0x80) { + while (((status = *addr) & (FPW)0x00800080) != (FPW)0x00800080) { if (get_timer_masked() > CFG_FLASH_ERASE_TOUT) { - *addr = 0xB0; /* suspend erase */ - *addr = 0xFF; /* reset to read mode */ - rc = ERR_TIMOUT; - goto outahere; - } - } - - /* clear status register command */ - *addr = 0x50; - /* reset to read mode */ - *addr = 0xFF; + printf ("Timeout\n"); + *addr = (FPW)0x00B000B0; /* suspend erase */ + *addr = (FPW)0x00FF00FF; /* reset to read mode */ + rcode = 1; + break; } - printf("ok.\n"); } - if (ctrlc()) - printf("User Interrupt!\n"); -outahere: + *addr = 0x00500050; /* clear status register cmd. */ + *addr = 0x00FF00FF; /* resest to read mode */ - /* allow flash to settle - wait 10 ms */ - udelay_masked(10000); - - if (flag) - enable_interrupts(); - - return rc; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash - */ - -static int write_word (flash_info_t *info, ulong dest, ushort data) -{ - vu_short *addr = (vu_short *)dest, val; - int rc = ERR_OK; - int flag; - - /* Check if Flash is (sufficiently) erased - */ - if ((*addr & data) != data) - return ERR_NOT_ERASED; - - /* - * Disable interrupts which might cause a timeout - * here. Remember that our exception vectors are - * at address 0 in the flash, and we don't want a - * (ticker) exception to happen while the flash - * chip is in programming mode. - */ - flag = disable_interrupts(); - - /* clear status register command */ - *addr = 0x50; - - /* program set-up command */ - *addr = 0x40; - - /* latch address/data */ - *addr = data; - - /* arm simple, non interrupt dependent timer */ - reset_timer_masked(); - - /* wait while polling the status register */ - while(((val = *addr) & 0x80) != 0x80) - { - if (get_timer_masked() > CFG_FLASH_WRITE_TOUT) { - rc = ERR_TIMOUT; - /* suspend program command */ - *addr = 0xB0; - goto outahere; - } - } - - if(val & 0x1A) { /* check for error */ - printf("\nFlash write error %02x at address %08lx\n", - (int)val, (unsigned long)dest); - if(val & (1<<3)) { - printf("Voltage range error.\n"); - rc = ERR_PROG_ERROR; - goto outahere; + printf (" done\n"); } - if(val & (1<<1)) { - printf("Device protect error.\n"); - rc = ERR_PROTECTED; - goto outahere; } - if(val & (1<<4)) { - printf("Programming error.\n"); - rc = ERR_PROG_ERROR; - goto outahere; - } - rc = ERR_PROG_ERROR; - goto outahere; - } - -outahere: - /* read array command */ - *addr = 0xFF; - - if (flag) - enable_interrupts(); - - return rc; + return rcode; } /*----------------------------------------------------------------------- - * Copy memory to flash. + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + * 4 - Flash not identified */ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) { ulong cp, wp; - ushort data; - int l; - int i, rc; + FPW data; + int count, i, l, rc, port_width; - wp = (addr & ~1); /* get lower word aligned address */ + if (info->flash_id == FLASH_UNKNOWN) { + return 4; + } +/* get lower word aligned address */ +#ifdef FLASH_PORT_WIDTH16 + wp = (addr & ~1); + port_width = 2; +#else + wp = (addr & ~3); + port_width = 4; +#endif /* * handle unaligned start bytes @@ -313,51 +323,110 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) if ((l = addr - wp) != 0) { data = 0; for (i=0, cp=wp; i> 8) | (*(uchar *)cp << 8); + data = (data << 8) | (*(uchar *)cp); } - for (; i<2 && cnt>0; ++i) { - data = (data >> 8) | (*src++ << 8); + for (; i0; ++i) { + data = (data << 8) | *src++; --cnt; ++cp; } - for (; cnt==0 && i<2; ++i, ++cp) { - data = (data >> 8) | (*(uchar *)cp << 8); + for (; cnt==0 && i= 2) { - data = *((vu_short*)src); - if ((rc = write_word(info, wp, data)) != 0) { + count = 0; + while (cnt >= port_width) { + data = 0; + for (i=0; i 0x800) + { + spin_wheel(); + count = 0; + } } if (cnt == 0) { - return ERR_OK; + return (0); } /* * handle unaligned tail bytes */ data = 0; - for (i=0, cp=wp; i<2 && cnt>0; ++i, ++cp) { - data = (data >> 8) | (*src++ << 8); + for (i=0, cp=wp; i0; ++i, ++cp) { + data = (data << 8) | *src++; --cnt; } - for (; i<2; ++i, ++cp) { - data = (data >> 8) | (*(uchar *)cp << 8); + for (; i CFG_FLASH_WRITE_TOUT) { + *addr = (FPW)0x00FF00FF; /* restore read mode */ + return (1); + } } - return write_word(info, wp, data); + *addr = (FPW)0x00FF00FF; /* restore read mode */ + + return (0); +} + +void inline +spin_wheel(void) +{ + static int r=0,p=0; + static char w[] = "\\/-"; + + printf("\010%c", w[p]); + (++p == 3) ? (p = 0) : 0; } + diff --git a/board/lubbock/lubbock.c b/board/lubbock/lubbock.c index ba9b86b314..2487a4cbae 100644 --- a/board/lubbock/lubbock.c +++ b/board/lubbock/lubbock.c @@ -47,7 +47,7 @@ int board_init (void) /* adress of boot parameters */ gd->bd->bi_boot_params = 0xa0000100; - return 1; + return 0; } int dram_init (void) @@ -62,6 +62,6 @@ int dram_init (void) gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; gd->bd->bi_dram[3].start = PHYS_SDRAM_4; gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; - return PHYS_SDRAM_1_SIZE + PHYS_SDRAM_2_SIZE + PHYS_SDRAM_3_SIZE + - PHYS_SDRAM_4_SIZE; + + return 0; } diff --git a/board/lubbock/memsetup.S b/board/lubbock/memsetup.S index c0278340a8..5bbd859585 100644 --- a/board/lubbock/memsetup.S +++ b/board/lubbock/memsetup.S @@ -39,12 +39,16 @@ DRAM_SIZE: .long CFG_DRAM_SIZE .endm +/* + * Memory setup + */ + .globl memsetup memsetup: mov r10, lr - /* Set up GPIO pins first */ + /* Set up GPIO pins first ----------------------------------------- */ ldr r0, =GPSR0 ldr r1, =CFG_GPSR0_VAL @@ -106,562 +110,284 @@ memsetup: ldr r1, =CFG_GAFR2_U_VAL str r1, [r0] - /* enable GPIO pins */ - ldr r0, =PSSR + ldr r0, =PSSR /* enable GPIO pins */ ldr r1, =CFG_PSSR_VAL str r1, [r0] - ldr r3, =MSC1 /* low - bank 2 Lubbock Registers / SRAM */ - ldr r2, =CFG_MSC1_VAL /* high - bank 3 Ethernet Controller */ - str r2, [r3] /* need to set MSC1 before trying to write to the HEX LEDs */ - ldr r2, [r3] /* need to read it back to make sure the value latches (see MSC section of manual) */ - - ldr r1, =LED_BLANK - mov r0, #0xFF - str r0, [r1] /* turn on hex leds */ - -loop: - ldr r0, =0xB0070001 - ldr r1, =_LED - str r0, [r1] /* hex display */ - -/********************************************************************* - Initlialize Memory Controller - The sequence below is based on the recommended init steps detailed - in the EAS, chapter 5 (Chapter 10, Operating Systems Developers Guide) - - - pause for 200 uSecs- allow internal clocks to settle - *Note: only need this if hard reset... doing it anyway for now -*/ - - @ ---- Wait 200 usec - ldr r3, =OSCR @ reset the OS Timer Count to zero + /* ---------------------------------------------------------------- */ + /* Enable memory interface */ + /* */ + /* The sequence below is based on the recommended init steps */ + /* detailed in the Intel PXA250 Operating Systems Developers Guide, */ + /* Chapter 10. */ + /* ---------------------------------------------------------------- */ + + /* ---------------------------------------------------------------- */ + /* Step 1: Wait for at least 200 microsedonds to allow internal */ + /* clocks to settle. Only necessary after hard reset... */ + /* FIXME: can be optimized later */ + /* ---------------------------------------------------------------- */ + + ldr r3, =OSCR /* reset the OS Timer Count to zero */ mov r2, #0 str r2, [r3] - ldr r4, =0x300 @ really 0x2E1 is about 200usec, so 0x300 should be plenty + ldr r4, =0x300 /* really 0x2E1 is about 200usec, */ + /* so 0x300 should be plenty */ 1: ldr r2, [r3] cmp r4, r2 bgt 1b mem_init: - @ get memory controller base address - ldr r1, =MEMC_BASE -@**************************************************************************** -@ Step 1 -@ + ldr r1, =MEMC_BASE /* get memory controller base addr. */ - @ write msc0, read back to ensure data latches - @ + /* ---------------------------------------------------------------- */ + /* Step 2a: Initialize Asynchronous static memory controller */ + /* ---------------------------------------------------------------- */ + + /* MSC registers: timing, bus width, mem type */ + + /* MSC0: nCS(0,1) */ ldr r2, =CFG_MSC0_VAL str r2, [r1, #MSC0_OFFSET] - ldr r2, [r1, #MSC0_OFFSET] - - @ write msc1 + ldr r2, [r1, #MSC0_OFFSET] /* read back to ensure */ + /* that data latches */ + /* MSC1: nCS(2,3) */ ldr r2, =CFG_MSC1_VAL str r2, [r1, #MSC1_OFFSET] ldr r2, [r1, #MSC1_OFFSET] - @ write msc2 + /* MSC2: nCS(4,5) */ ldr r2, =CFG_MSC2_VAL str r2, [r1, #MSC2_OFFSET] ldr r2, [r1, #MSC2_OFFSET] - @ write mecr + /* ---------------------------------------------------------------- */ + /* Step 2b: Initialize Card Interface */ + /* ---------------------------------------------------------------- */ + + /* MECR: Memory Expansion Card Register */ ldr r2, =CFG_MECR_VAL str r2, [r1, #MECR_OFFSET] + ldr r2, [r1, #MECR_OFFSET] - @ write mcmem0 + /* MCMEM0: Card Interface slot 0 timing */ ldr r2, =CFG_MCMEM0_VAL str r2, [r1, #MCMEM0_OFFSET] + ldr r2, [r1, #MCMEM0_OFFSET] - @ write mcmem1 + /* MCMEM1: Card Interface slot 1 timing */ ldr r2, =CFG_MCMEM1_VAL str r2, [r1, #MCMEM1_OFFSET] + ldr r2, [r1, #MCMEM1_OFFSET] - @ write mcatt0 + /* MCATT0: Card Interface Attribute Space Timing, slot 0 */ ldr r2, =CFG_MCATT0_VAL str r2, [r1, #MCATT0_OFFSET] + ldr r2, [r1, #MCATT0_OFFSET] - @ write mcatt1 + /* MCATT1: Card Interface Attribute Space Timing, slot 1 */ ldr r2, =CFG_MCATT1_VAL str r2, [r1, #MCATT1_OFFSET] + ldr r2, [r1, #MCATT1_OFFSET] - @ write mcio0 + /* MCIO0: Card Interface I/O Space Timing, slot 0 */ ldr r2, =CFG_MCIO0_VAL str r2, [r1, #MCIO0_OFFSET] + ldr r2, [r1, #MCIO0_OFFSET] - @ write mcio1 + /* MCIO1: Card Interface I/O Space Timing, slot 1 */ ldr r2, =CFG_MCIO1_VAL str r2, [r1, #MCIO1_OFFSET] + ldr r2, [r1, #MCIO1_OFFSET] - @------------------------------------------------------- - @ 3rd bullet, Step 1 - @ + /* ---------------------------------------------------------------- */ + /* Step 2c: Write FLYCNFG FIXME: what's that??? */ + /* ---------------------------------------------------------------- */ - @ get the mdrefr settings - ldr r3, =CFG_MDREFR_VAL_100 - @ extract DRI field (we need a valid DRI field) - @ - ldr r2, =0xFFF + /* ---------------------------------------------------------------- */ + /* Step 2d: Initialize Timing for Sync Memory (SDCLK0) */ + /* ---------------------------------------------------------------- */ - @ valid DRI field in r3 - @ - and r3, r3, r2 + /* Before accessing MDREFR we need a valid DRI field, so we set */ + /* this to power on defaults + DRI field. */ - @ get the reset state of MDREFR - @ + ldr r3, =CFG_MDREFR_VAL + ldr r2, =0xFFF + and r3, r3, r2 + ldr r4, =0x03ca4000 + orr r4, r4, r3 + str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ ldr r4, [r1, #MDREFR_OFFSET] - @ clear the DRI field - @ - bic r4, r4, r2 - - @ insert the valid DRI field loaded above - @ - orr r4, r4, r3 - - @ write back mdrefr - @ - str r4, [r1, #MDREFR_OFFSET] - - @ *Note: preserve the mdrefr value in r4 * - -@**************************************************************************** -@ Step 2 -@ - /* This should be for SRAM, why is it commented out??? */ - - @ fetch sxcnfg value - @ - @ldr r2, =0 - @ write back sxcnfg - @str r2, [r1, #SXCNFG_OFFSET] - -/* @if sxcnfg=0, don't program for synch-static memory */ - @cmp r2, #0 - @beq 1f - - @program sxmrs - @ldr r2, =SXMRS_SETTINGS - @str r2, [r1, #SXMRS_OFFSET] - - -@**************************************************************************** -@ Step 3 -@ - - @ Assumes previous mdrefr value in r4, if not then read current mdrefr - - @ clear the free-running clock bits - @ (clear K0Free, K1Free, K2Free - @ - bic r4, r4, #(0x00800000 | 0x01000000 | 0x02000000) - - @ set K1RUN if bank 0 installed - @ - orr r4, r4, #0x00010000 - - - -#ifdef THIS -@ 100MHz. - @ - @ Adjust MSC0 for MemClks > 100 MHz - @ - ldreq r0, [r1, #MSC0_OFFSET] - ldreq r3, =0x7F007F00 - biceq r0, r0, r3 @ clear MSC0[14:12, 11:8] (RRR, RDN) - ldreq r3, =0x46004600 - orreq r0, r0, r3 @ set MSC0[14, 10:9] (doubling RRR, RDN) - streq r0, [r1, #MSC0_OFFSET] - ldreq r0, [r1, #MSC0_OFFSET] @ read it back to ensure that the data latches - - @ - @ Adjust MSC1.LH for MemClks > 100 MHz - @ - ldreq r0, [r1, #MSC1_OFFSET] - ldreq r3, =0x7FF0 - biceq r0, r0, r3 @ clear MSC1[14:12, 11:8, 7:4] (RRR, RDN, RDF) - ldreq r3, =0x4880 - orreq r0, r0, r3 @ set MSC1[14, 11, 7] (doubling RRR, RDN, RDF) - streq r0, [r1, #MSC1_OFFSET] - ldreq r0, [r1, #MSC1_OFFSET] @ read it back to ensure that the data latches - - @ @ - @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ -#endif + /* Note: preserve the mdrefr value in r4 */ -@ #include #include +#include +#include /* * I/O Port configuration table @@ -167,8 +169,8 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ - /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 1, 0, 0, 1, 0, 0 }, /* LED */ + /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ + /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ @@ -197,76 +199,222 @@ typedef struct bscr_ { unsigned long bcsr7; } bcsr_t; -void reset_phy(void) +void reset_phy (void) { - volatile bcsr_t *bcsr = (bcsr_t *)CFG_BCSR; + volatile bcsr_t *bcsr = (bcsr_t *) CFG_BCSR; - /* reset the FEC port */ - bcsr->bcsr1 &= ~FETH_RST; - bcsr->bcsr1 |= FETH_RST; + /* reset the FEC port */ + bcsr->bcsr1 &= ~FETH_RST; + bcsr->bcsr1 |= FETH_RST; } int board_pre_init (void) { - volatile bcsr_t *bcsr = (bcsr_t *)CFG_BCSR; - bcsr->bcsr1 = ~FETHIEN & ~RS232EN_1; + volatile bcsr_t *bcsr = (bcsr_t *) CFG_BCSR; - return 0; + bcsr->bcsr1 = ~FETHIEN & ~RS232EN_1; + + return 0; } -long int initdram(int board_type) +#define ns2clk(ns) (ns / (1000000000 / CONFIG_8260_CLKIN) + 1) + +long int initdram (int board_type) { - volatile immap_t *immap = (immap_t *)CFG_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - volatile uchar *ramaddr, - c = 0xff; - int i; + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile memctl8260_t *memctl = &immap->im_memctl; + volatile uchar *ramaddr, c = 0xff; + + /* Initialisation is for 16MB DIMM the board is shipped with */ + long int msize = 16; + uint or = 0xFF000CA0; + uint psdmr = CFG_PSDMR; + uint psrt = CFG_PSRT; + + int i; #ifndef CFG_RAMBOOT - immap->im_siu_conf.sc_ppc_acr = 0x00000002; - immap->im_siu_conf.sc_ppc_alrh = 0x01267893; - immap->im_siu_conf.sc_tescr1 = 0x00004000; - - /* init local sdram, bank 4 */ - memctl->memc_lsrt = 0x00000010; - memctl->memc_or4 = 0xFFC01480; - memctl->memc_br4 = 0x04001861; - memctl->memc_lsdmr = 0x2886A522; - ramaddr = (uchar *)CFG_LSDRAM_BASE; - *ramaddr = c; - memctl->memc_lsdmr = 0x0886A522; - for( i = 0; i < 8; i++ ) { - *ramaddr = c; - } - memctl->memc_lsdmr = 0x1886A522; - *ramaddr = c; - memctl->memc_lsdmr = 0x4086A522; - - /* init sdram dimm */ - ramaddr = (uchar *)CFG_SDRAM_BASE; - memctl->memc_psrt = 0x00000010; - immap->im_memctl.memc_or2 = 0xFF000CA0; - immap->im_memctl.memc_br2 = 0x00000041; - memctl->memc_psdmr = 0x296EB452; - *ramaddr = c; - memctl->memc_psdmr = 0x096EB452; - for (i = 0; i < 8; i++) - *ramaddr = c; - - memctl->memc_psdmr = 0x196EB452; - *ramaddr = c; - memctl->memc_psdmr = 0x416EB452; - *ramaddr = c; + immap->im_siu_conf.sc_ppc_acr = 0x00000002; + immap->im_siu_conf.sc_ppc_alrh = 0x01267893; + immap->im_siu_conf.sc_tescr1 = 0x00004000; + + memctl->memc_mptpr = CFG_MPTPR; + /* init local sdram, bank 4 */ + memctl->memc_lsrt = 0x00000010; + memctl->memc_or4 = 0xFFC01480; + memctl->memc_br4 = 0x04001861; + memctl->memc_lsdmr = 0x2886A522; + ramaddr = (uchar *) CFG_LSDRAM_BASE; + *ramaddr = c; + memctl->memc_lsdmr = 0x0886A522; + for (i = 0; i < 8; i++) { + *ramaddr = c; + } + memctl->memc_lsdmr = 0x1886A522; + *ramaddr = c; + memctl->memc_lsdmr = 0x4086A522; + + /* init sdram dimm */ +#ifdef CONFIG_SPD_EEPROM + { + spd_eeprom_t spd; + uint pbi, bsel, rowst, lsb, tmp; + + i2c_read (CONFIG_SPD_ADDR, 0, 1, (uchar *) & spd, sizeof (spd)); + + /* Bank-based interleaving is not supported for physical bank + sizes greater than 128MB which is encoded as 0x20 in SPD + */ + pbi = (spd.row_dens > 32) ? 1 : CONFIG_SDRAM_PBI; + msize = spd.nrows * (4 * spd.row_dens); /* Mixed size not supported */ + or = ~(msize - 1) << 20; /* SDAM */ + switch (spd.nbanks) { /* BPD */ + case 2: + bsel = 1; + break; + case 4: + bsel = 2; + or |= 0x00002000; + break; + case 8: + bsel = 3; + or |= 0x00004000; + break; + } + lsb = 3; /* For 64-bit port, lsb is 3 bits */ + + if (pbi) { /* Bus partition depends on interleaving */ + rowst = 32 - (spd.nrow_addr + spd.ncol_addr + bsel + lsb); + or |= (rowst << 9); /* ROWST */ + } else { + rowst = 32 - (spd.nrow_addr + spd.ncol_addr + lsb); + or |= ((rowst * 2 - 12) << 9); /* ROWST */ + } + or |= ((spd.nrow_addr - 9) << 6); /* NUMR */ + + psdmr = (pbi << 31); /* PBI */ + /* Bus multiplexing parameters */ + tmp = 32 - (lsb + spd.nrow_addr); /* Tables 10-19 and 10-20 */ + psdmr |= ((tmp - (rowst - 5) - 13) << 24); /* SDAM */ + psdmr |= ((tmp - 3 - 12) << 21); /* BSMA */ + + tmp = (31 - lsb - 10) - tmp; + /* Pin connected to SDA10 is (31 - lsb - 10). + rowst is multiplexed over (32 - (lsb + spd.nrow_addr)), + so (rowst + tmp) alternates with AP. + */ + if (pbi) /* Table 10-7 */ + psdmr |= ((10 - (rowst + tmp)) << 18); /* SDA10 */ + else + psdmr |= ((12 - (rowst + tmp)) << 18); /* SDA10 */ + + /* SDRAM device-specific parameters */ + tmp = ns2clk (70); /* Refresh recovery is not in SPD, so assume 70ns */ + switch (tmp) { /* RFRC */ + case 1: + case 2: + psdmr |= (1 << 15); + break; + case 3: + case 4: + case 5: + case 6: + case 7: + case 8: + psdmr |= ((tmp - 2) << 15); + break; + default: + psdmr |= (7 << 15); + } + psdmr |= (ns2clk (spd.trp) % 8 << 12); /* PRETOACT */ + psdmr |= (ns2clk (spd.trcd) % 8 << 9); /* ACTTORW */ + /* BL=0 because for 64-bit SDRAM burst length must be 4 */ + /* LDOTOPRE ??? */ + for (i = 0, tmp = spd.write_lat; (i < 4) && ((tmp & 1) == 0); i++) + tmp >>= 1; + switch (i) { /* WRC */ + case 0: + case 1: + psdmr |= (1 << 4); + break; + case 2: + case 3: + psdmr |= (i << 4); + break; + } + /* EAMUX=0 - no external address multiplexing */ + /* BUFCMD=0 - no external buffers */ + for (i = 1, tmp = spd.cas_lat; (i < 3) && ((tmp & 1) == 0); i++) + tmp >>= 1; + psdmr |= i; /* CL */ + + switch (spd.refresh & 0x7F) { + case 1: + tmp = 3900; + break; + case 2: + tmp = 7800; + break; + case 3: + tmp = 31300; + break; + case 4: + tmp = 62500; + break; + case 5: + tmp = 125000; + break; + default: + tmp = 15625; + } + psrt = tmp / (1000000000 / CONFIG_8260_CLKIN * + ((memctl->memc_mptpr >> 8) + 1)) - 1; +#ifdef SPD_DEBUG + printf ("\nDIMM type: %-18.18s\n", spd.mpart); + printf ("SPD size: %d\n", spd.info_size); + printf ("EEPROM size: %d\n", 1 << spd.chip_size); + printf ("Memory type: %d\n", spd.mem_type); + printf ("Row addr: %d\n", spd.nrow_addr); + printf ("Column addr: %d\n", spd.ncol_addr); + printf ("# of rows: %d\n", spd.nrows); + printf ("Row density: %d\n", spd.row_dens); + printf ("# of banks: %d\n", spd.nbanks); + printf ("Data width: %d\n", + 256 * spd.dataw_msb + spd.dataw_lsb); + printf ("Chip width: %d\n", spd.primw); + printf ("Refresh rate: %02X\n", spd.refresh); + printf ("CAS latencies: %02X\n", spd.cas_lat); + printf ("Write latencies: %02X\n", spd.write_lat); + printf ("tRP: %d\n", spd.trp); + printf ("tRCD: %d\n", spd.trcd); + + printf ("OR=%X, PSDMR=%08X, PSRT=%0X\n", or, psdmr, psrt); +#endif /* SPD_DEBUG */ + } +#endif /* CONFIG_SPD_EEPROM */ + memctl->memc_psrt = psrt; + memctl->memc_or2 = or; + memctl->memc_br2 = CFG_SDRAM_BASE | 0x00000041; + ramaddr = (uchar *) CFG_SDRAM_BASE; + memctl->memc_psdmr = psdmr | 0x28000000; /* Precharge all banks */ + *ramaddr = c; + memctl->memc_psdmr = psdmr | 0x08000000; /* CBR refresh */ + for (i = 0; i < 8; i++) + *ramaddr = c; + + memctl->memc_psdmr = psdmr | 0x18000000; /* Mode Register write */ + *ramaddr = c; + memctl->memc_psdmr = psdmr | 0x40000000; /* Refresh enable */ + *ramaddr = c; #endif - /* return total ram size of simm */ - return (16 * 1024 * 1024); + /* return total ram size of DIMM */ + return (msize * 1024 * 1024); } -int checkboard(void) +int checkboard (void) { - puts ("Board: Motorola MPC8260ADS\n"); - return 0; + puts ("Board: Motorola MPC8260ADS\n"); + return 0; } - diff --git a/board/mpc8266ads/Makefile b/board/mpc8266ads/Makefile new file mode 100644 index 0000000000..9280bf7d60 --- /dev/null +++ b/board/mpc8266ads/Makefile @@ -0,0 +1,46 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := $(BOARD).o flash.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $^ + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff --git a/board/mpc8266ads/config.mk b/board/mpc8266ads/config.mk new file mode 100644 index 0000000000..9d55598264 --- /dev/null +++ b/board/mpc8266ads/config.mk @@ -0,0 +1,32 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Modified by, Stuart Hughes, Lineo Inc, stuarth@lineo.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# mpc8260ads board +# + +TEXT_BASE = 0xfff00000 + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/board diff --git a/board/mpc8266ads/flash.c b/board/mpc8266ads/flash.c new file mode 100644 index 0000000000..5ec6e33cfc --- /dev/null +++ b/board/mpc8266ads/flash.c @@ -0,0 +1,509 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com + * Add support the Sharp chips on the mpc8260ads. + * I started with board/ip860/flash.c and made changes I found in + * the MTD project by David Schleef. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +#if defined(CFG_ENV_IS_IN_FLASH) +# ifndef CFG_ENV_ADDR +# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_ENV_OFFSET) +# endif +# ifndef CFG_ENV_SIZE +# define CFG_ENV_SIZE CFG_ENV_SECT_SIZE +# endif +# ifndef CFG_ENV_SECT_SIZE +# define CFG_ENV_SECT_SIZE CFG_ENV_SIZE +# endif +#endif + +/*----------------------------------------------------------------------- + * Functions + */ +static ulong flash_get_size (vu_long *addr, flash_info_t *info); +static int write_word (flash_info_t *info, ulong dest, ulong data); +static int clear_block_lock_bit(vu_long * addr); + +/*----------------------------------------------------------------------- + */ + +unsigned long flash_init (void) +{ +#ifndef CONFIG_MPC8260ADS + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + volatile ip860_bcsr_t *bcsr = (ip860_bcsr_t *)BCSR_BASE; +#endif + unsigned long size; + int i; + + /* Init: enable write, + * or we cannot even write flash commands + */ +#ifndef CONFIG_MPC8260ADS + bcsr->bd_ctrl |= BD_CTRL_FLWE; +#endif + + + for (i=0; imemc_or1 = CFG_OR_TIMING_FLASH | (-size & 0xFFFF8000); + memctl->memc_br1 = (CFG_FLASH_BASE & BR_BA_MSK) | + (memctl->memc_br1 & ~(BR_BA_MSK)); +#endif + /* Re-do sizing to get full correct info */ + size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]); + + flash_info[0].size = size; + +#if CFG_MONITOR_BASE >= CFG_FLASH_BASE + /* monitor protection ON by default */ + flash_protect(FLAG_PROTECT_SET, + CFG_MONITOR_BASE, + CFG_MONITOR_BASE+CFG_MONITOR_LEN-1, + &flash_info[0]); +#endif + +#ifdef CFG_ENV_IS_IN_FLASH + /* ENV protection ON by default */ + flash_protect(FLAG_PROTECT_SET, + CFG_ENV_ADDR, + CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1, + &flash_info[0]); +#endif + return (size); +} + +/*----------------------------------------------------------------------- + */ +void flash_print_info (flash_info_t *info) +{ + int i; + + if (info->flash_id == FLASH_UNKNOWN) { + printf ("missing or unknown FLASH type\n"); + return; + } + + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_INTEL: printf ("Intel "); break; + case FLASH_MAN_SHARP: printf ("Sharp "); break; + default: printf ("Unknown Vendor "); break; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_28F016SV: printf ("28F016SV (16 Mbit, 32 x 64k)\n"); + break; + case FLASH_28F160S3: printf ("28F160S3 (16 Mbit, 32 x 512K)\n"); + break; + case FLASH_28F320S3: printf ("28F320S3 (32 Mbit, 64 x 512K)\n"); + break; + case FLASH_LH28F016SCT: printf ("28F016SC (16 Mbit, 32 x 64K)\n"); + break; + default: printf ("Unknown Chip Type\n"); + break; + } + + printf (" Size: %ld MB in %d Sectors\n", + info->size >> 20, info->sector_count); + + printf (" Sector Start Addresses:"); + for (i=0; isector_count; ++i) { + if ((i % 5) == 0) + printf ("\n "); + printf (" %08lX%s", + info->start[i], + info->protect[i] ? " (RO)" : " " + ); + } + printf ("\n"); +} + +/*----------------------------------------------------------------------- + */ + + +/*----------------------------------------------------------------------- + */ + +/* + * The following code cannot be run from FLASH! + */ + +static ulong flash_get_size (vu_long *addr, flash_info_t *info) +{ + short i; + ulong value; + ulong base = (ulong)addr; + ulong sector_offset; + + /* Write "Intelligent Identifier" command: read Manufacturer ID */ + *addr = 0x90909090; + + value = addr[0] & 0x00FF00FF; + switch (value) { + case MT_MANUFACT: /* SHARP, MT or => Intel */ + case INTEL_ALT_MANU: + info->flash_id = FLASH_MAN_INTEL; + break; + default: + printf("unknown manufacturer: %x\n", (unsigned int)value); + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + return (0); /* no or unknown flash */ + } + + value = addr[1]; /* device ID */ + + switch (value) { + case (INTEL_ID_28F016S): + info->flash_id += FLASH_28F016SV; + info->sector_count = 32; + info->size = 0x00400000; + sector_offset = 0x20000; + break; /* => 2x2 MB */ + + case (INTEL_ID_28F160S3): + info->flash_id += FLASH_28F160S3; + info->sector_count = 32; + info->size = 0x00400000; + sector_offset = 0x20000; + break; /* => 2x2 MB */ + + case (INTEL_ID_28F320S3): + info->flash_id += FLASH_28F320S3; + info->sector_count = 64; + info->size = 0x00800000; + sector_offset = 0x20000; + break; /* => 2x4 MB */ + + case SHARP_ID_28F016SCL: + case SHARP_ID_28F016SCZ: + info->flash_id = FLASH_MAN_SHARP | FLASH_LH28F016SCT; + info->sector_count = 32; + info->size = 0x00800000; + sector_offset = 0x40000; + break; /* => 4x2 MB */ + + + default: + info->flash_id = FLASH_UNKNOWN; + return (0); /* => no or unknown flash */ + + } + + /* set up sector start address table */ + for (i = 0; i < info->sector_count; i++) { + info->start[i] = base; + base += sector_offset; + /* don't know how to check sector protection */ + info->protect[i] = 0; + } + + /* + * Prevent writes to uninitialized FLASH. + */ + if (info->flash_id != FLASH_UNKNOWN) { + addr = (vu_long *)info->start[0]; + + *addr = 0xFFFFFF; /* reset bank to read array mode */ + } + + return (info->size); +} + + +/*----------------------------------------------------------------------- + */ + +int flash_erase (flash_info_t *info, int s_first, int s_last) +{ + int flag, prot, sect; + ulong start, now, last; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf ("- missing\n"); + } else { + printf ("- no sectors to erase\n"); + } + return 1; + } + + if ( ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) + && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) { + printf ("Can't erase unknown flash type %08lx - aborted\n", + info->flash_id); + return 1; + } + + prot = 0; + for (sect=s_first; sect<=s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) { + printf ("- Warning: %d protected sectors will not be erased!\n", + prot); + } else { + printf ("\n"); + } + + /* Make Sure Block Lock Bit is not set. */ + if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){ + return 1; + } + + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect<=s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + vu_long *addr = (vu_long *)(info->start[sect]); + + last = start = get_timer (0); + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + /* Reset Array */ + *addr = 0xffffffff; + /* Clear Status Register */ + *addr = 0x50505050; + /* Single Block Erase Command */ + *addr = 0x20202020; + /* Confirm */ + *addr = 0xD0D0D0D0; + + if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) { + /* Resume Command, as per errata update */ + *addr = 0xD0D0D0D0; + } + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* wait at least 80us - let's wait 1 ms */ + udelay (1000); + while ((*addr & 0x80808080) != 0x80808080) { + if(*addr & 0x20202020){ + printf("Error in Block Erase - Lock Bit may be set!\n"); + printf("Status Register = 0x%X\n", (uint)*addr); + *addr = 0xFFFFFFFF; /* reset bank */ + return 1; + } + if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) { + printf ("Timeout\n"); + *addr = 0xFFFFFFFF; /* reset bank */ + return 1; + } + /* show that we're waiting */ + if ((now - last) > 1000) { /* every second */ + putc ('.'); + last = now; + } + } + + /* reset to read mode */ + *addr = 0xFFFFFFFF; + } + } + + printf (" done\n"); + return 0; +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ + +int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) +{ + ulong cp, wp, data; + int i, l, rc; + + wp = (addr & ~3); /* get lower word aligned address */ + + /* + * handle unaligned start bytes + */ + if ((l = addr - wp) != 0) { + data = 0; + for (i=0, cp=wp; i0; ++i) { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt==0 && i<4; ++i, ++cp) { + data = (data << 8) | (*(uchar *)cp); + } + + if ((rc = write_word(info, wp, data)) != 0) { + return (rc); + } + wp += 4; + } + + /* + * handle word aligned part + */ + while (cnt >= 4) { + data = 0; + for (i=0; i<4; ++i) { + data = (data << 8) | *src++; + } + if ((rc = write_word(info, wp, data)) != 0) { + return (rc); + } + wp += 4; + cnt -= 4; + } + + if (cnt == 0) { + return (0); + } + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) { + data = (data << 8) | *src++; + --cnt; + } + for (; i<4; ++i, ++cp) { + data = (data << 8) | (*(uchar *)cp); + } + + return (write_word(info, wp, data)); +} + +/*----------------------------------------------------------------------- + * Write a word to Flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int write_word (flash_info_t *info, ulong dest, ulong data) +{ + vu_long *addr = (vu_long *)dest; + ulong start, csr; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ((*addr & data) != data) { + return (2); + } + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + /* Write Command */ + *addr = 0x10101010; + + /* Write Data */ + *addr = data; + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* data polling for D7 */ + start = get_timer (0); + flag = 0; + while (((csr = *addr) & 0x80808080) != 0x80808080) { + if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { + flag = 1; + break; + } + } + if (csr & 0x40404040) { + printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr); + flag = 1; + } + + /* Clear Status Registers Command */ + *addr = 0x50505050; + /* Reset to read array mode */ + *addr = 0xFFFFFFFF; + + return (flag); +} + +/*----------------------------------------------------------------------- + * Clear Block Lock Bit, returns: + * 0 - OK + * 1 - Timeout + */ + +static int clear_block_lock_bit(vu_long * addr) +{ + ulong start, now; + + /* Reset Array */ + *addr = 0xffffffff; + /* Clear Status Register */ + *addr = 0x50505050; + + *addr = 0x60606060; + *addr = 0xd0d0d0d0; + + start = get_timer (0); + while(*addr != 0x80808080){ + if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) { + printf ("Timeout on clearing Block Lock Bit\n"); + *addr = 0xFFFFFFFF; /* reset bank */ + return 1; + } + } + return 0; +} diff --git a/board/mpc8266ads/mpc8266ads.c b/board/mpc8266ads/mpc8266ads.c new file mode 100644 index 0000000000..796b37de1e --- /dev/null +++ b/board/mpc8266ads/mpc8266ads.c @@ -0,0 +1,565 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * Modified during 2001 by + * Advanced Communications Technologies (Australia) Pty. Ltd. + * Howard Walker, Tuong Vu-Dinh + * + * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com + * Added support for the 16M dram simm on the 8260ads boards + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include + +/* + * PBI Page Based Interleaving + * PSDMR_PBI page based interleaving + * 0 bank based interleaving + * External Address Multiplexing (EAMUX) adds a clock to address cycles + * (this can help with marginal board layouts) + * PSDMR_EAMUX adds a clock + * 0 no extra clock + * Buffer Command (BUFCMD) adds a clock to command cycles. + * PSDMR_BUFCMD adds a clock + * 0 no extra clock + */ +#define CONFIG_PBI 0 +#define PESSIMISTIC_SDRAM 0 +#define EAMUX 0 /* EST requires EAMUX */ +#define BUFCMD 0 + + +/* + * I/O Port configuration table + * + * if conf is 1, then that port pin will be configured at boot time + * according to the five values podr/pdir/ppar/psor/pdat for that entry + */ + +const iop_conf_t iop_conf_tab[4][32] = { + + /* Port A configuration */ + { /* conf ppar psor pdir podr pdat */ + /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */ + /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */ + /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */ + /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */ + /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */ + /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */ + /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ + /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ + /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ + /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ + /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ + /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ + /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ + /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ + /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */ + /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */ + /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */ + /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */ + /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */ + /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */ + /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */ + /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */ + /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */ + /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */ + /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ + /* PA6 */ { 1, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */ + /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ + /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ + /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ + /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ + /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */ + /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ + }, + + /* Port B configuration */ + { /* conf ppar psor pdir podr pdat */ + /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ + /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ + /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ + /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ + /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ + /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ + /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ + /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ + /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ + /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ + /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ + /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ + /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ + /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ + /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */ + /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */ + /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */ + /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */ + /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */ + /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */ + /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ + }, + + /* Port C */ + { /* conf ppar psor pdir podr pdat */ + /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ + /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ + /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ + /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ + /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */ + /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ + /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ + /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ + /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ + /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ + /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ + /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ + /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */ + /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */ + /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */ + /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */ + /* PC15 */ { 0, 0, 0, 1, 0, 0 }, /* PC15 */ + /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ + /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */ + /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */ + /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */ + /* PC10 */ { 1, 1, 0, 0, 0, 0 }, /* LXT970 FETHMDC */ + /* PC9 */ { 1, 1, 0, 0, 0, 0 }, /* LXT970 FETHMDIO */ + /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ + /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ + /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ + /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ + /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ + /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ + /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ + /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ + /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ + }, + + /* Port D */ + { /* conf ppar psor pdir podr pdat */ + /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ + /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ + /* PD29 */ { 0, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ + /* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */ + /* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */ + /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */ + /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ + /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ + /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ + /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ + /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ + /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ + /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ + /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ + /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ + /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ + /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ + /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ + /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ + /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ + /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ + /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ + /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ + /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ + /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ + /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ + /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ + /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ + /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ + } +}; + +typedef struct bscr_ { + unsigned long bcsr0; + unsigned long bcsr1; + unsigned long bcsr2; + unsigned long bcsr3; + unsigned long bcsr4; + unsigned long bcsr5; + unsigned long bcsr6; + unsigned long bcsr7; +} bcsr_t; + +void reset_phy(void) +{ + volatile bcsr_t *bcsr = (bcsr_t *)CFG_BCSR; + + /* reset the FEC port */ + bcsr->bcsr1 &= ~FETH_RST; + bcsr->bcsr1 |= FETH_RST; +} + + +int board_pre_init (void) +{ + volatile bcsr_t *bcsr = (bcsr_t *)CFG_BCSR; + bcsr->bcsr1 = ~FETHIEN & ~RS232EN_1; + + return 0; +} + +int checkboard(void) +{ + puts ("Board: Motorola MPC8266ADS\n"); + return 0; +} + +long int initdram(int board_type) +{ + /* Autoinit part stolen from board/sacsng/sacsng.c */ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile memctl8260_t *memctl = &immap->im_memctl; + volatile uchar c = 0xff; + volatile uchar *ramaddr = (uchar *)(CFG_SDRAM_BASE + 0x8); + uint psdmr = CFG_PSDMR; + int i; + + uint psrt = 14; /* for no SPD */ + uint chipselects = 1; /* for no SPD */ + uint sdram_size = CFG_SDRAM_SIZE * 1024 * 1024; /* for no SPD */ + uint or = CFG_OR2_PRELIM; /* for no SPD */ + uint data_width; + uint rows; + uint banks; + uint cols; + uint caslatency; + uint width; + uint rowst; + uint sdam; + uint bsma; + uint sda10; + u_char spd_size; + u_char data; + u_char cksum; + int j; + + /* Keep the compiler from complaining about potentially uninitialized vars */ + data_width = chipselects = rows = banks = cols = caslatency = psrt = 0; + + /* + * Read the SDRAM SPD EEPROM via I2C. + */ + i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE); + + i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1); + spd_size = data; + cksum = data; + for(j = 1; j < 64; j++) + { /* read only the checksummed bytes */ + /* note: the I2C address autoincrements when alen == 0 */ + i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1); + /*printf("addr %d = 0x%02x\n", j, data);*/ + if(j == 5) chipselects = data & 0x0F; + else if(j == 6) data_width = data; + else if(j == 7) data_width |= data << 8; + else if(j == 3) rows = data & 0x0F; + else if(j == 4) cols = data & 0x0F; + else if(j == 12) + { + /* + * Refresh rate: this assumes the prescaler is set to + * approximately 1uSec per tick. + */ + switch(data & 0x7F) + { + default: + case 0: psrt = 16; /* 15.625uS */ break; + case 1: psrt = 2; /* 3.9uS */ break; + case 2: psrt = 6; /* 7.8uS */ break; + case 3: psrt = 29; /* 31.3uS */ break; + case 4: psrt = 60; /* 62.5uS */ break; + case 5: psrt = 120; /* 125uS */ break; + } + } + else if(j == 17) banks = data; + else if(j == 18) + { + caslatency = 3; /* default CL */ +# if(PESSIMISTIC_SDRAM) + if((data & 0x04) != 0) caslatency = 3; + else if((data & 0x02) != 0) caslatency = 2; + else if((data & 0x01) != 0) caslatency = 1; +# else + if((data & 0x01) != 0) caslatency = 1; + else if((data & 0x02) != 0) caslatency = 2; + else if((data & 0x04) != 0) caslatency = 3; +# endif + else + { + printf ("WARNING: Unknown CAS latency 0x%02X, using 3\n", + data); + } + } + else if(j == 63) + { + if(data != cksum) + { + printf ("WARNING: Configuration data checksum failure:" + " is 0x%02x, calculated 0x%02x\n", + data, cksum); + } + } + cksum += data; + } + + /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */ + if(caslatency < 2) { + printf("CL was %d, forcing to 2\n", caslatency); + caslatency = 2; + } + if(rows > 14) { + printf("This doesn't look good, rows = %d, should be <= 14\n", rows); + rows = 14; + } + if(cols > 11) { + printf("This doesn't look good, columns = %d, should be <= 11\n", cols); + cols = 11; + } + + if((data_width != 64) && (data_width != 72)) + { + printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n", + data_width); + } + width = 3; /* 2^3 = 8 bytes = 64 bits wide */ + /* + * Convert banks into log2(banks) + */ + if (banks == 2) banks = 1; + else if(banks == 4) banks = 2; + else if(banks == 8) banks = 3; + + + sdram_size = 1 << (rows + cols + banks + width); + +#if(CONFIG_PBI == 0) /* bank-based interleaving */ + rowst = ((32 - 6) - (rows + cols + width)) * 2; +#else + rowst = 32 - (rows + banks + cols + width); +#endif + + or = ~(sdram_size - 1) | /* SDAM address mask */ + ((banks-1) << 13) | /* banks per device */ + (rowst << 9) | /* rowst */ + ((rows - 9) << 6); /* numr */ + + + /*printf("memctl->memc_or2 = 0x%08x\n", or);*/ + + /* + * SDAM specifies the number of columns that are multiplexed + * (reference AN2165/D), defined to be (columns - 6) for page + * interleave, (columns - 8) for bank interleave. + * + * BSMA is 14 - max(rows, cols). The bank select lines come + * into play above the highest "address" line going into the + * the SDRAM. + */ +#if(CONFIG_PBI == 0) /* bank-based interleaving */ + sdam = cols - 8; + bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols); + sda10 = sdam + 2; +#else + sdam = cols - 6; + bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols); + sda10 = sdam; +#endif +#if(PESSIMISTIC_SDRAM) + psdmr = (CONFIG_PBI |\ + PSDMR_RFEN |\ + PSDMR_RFRC_16_CLK |\ + PSDMR_PRETOACT_8W |\ + PSDMR_ACTTORW_8W |\ + PSDMR_WRC_4C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD) |\ + caslatency |\ + ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */ \ + (sdam << 24) |\ + (bsma << 21) |\ + (sda10 << 18); +#else + psdmr = (CONFIG_PBI |\ + PSDMR_RFEN |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */ \ + PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */ \ + PSDMR_WRC_1C | /* 1 clock + 7nSec */ + EAMUX |\ + BUFCMD) |\ + caslatency |\ + ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */ \ + (sdam << 24) |\ + (bsma << 21) |\ + (sda10 << 18); +#endif + /*printf("psdmr = 0x%08x\n", psdmr);*/ + + /* + * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): + * + * "At system reset, initialization software must set up the + * programmable parameters in the memory controller banks registers + * (ORx, BRx, P/LSDMR). After all memory parameters are configured, + * system software should execute the following initialization sequence + * for each SDRAM device. + * + * 1. Issue a PRECHARGE-ALL-BANKS command + * 2. Issue eight CBR REFRESH commands + * 3. Issue a MODE-SET command to initialize the mode register + * + * Quote from Micron MT48LC8M16A2 data sheet: + * + * "...the SDRAM requires a 100uS delay prior to issuing any + * command other than a COMMAND INHIBIT or NOP. Starting at some + * point during this 100uS period and continuing at least through + * the end of this period, COMMAND INHIBIT or NOP commands should + * be applied." + * + * "Once the 100uS delay has been satisfied with at least one COMMAND + * INHIBIT or NOP command having been applied, a /PRECHARGE command/ + * should be applied. All banks must then be precharged, thereby + * placing the device in the all banks idle state." + * + * "Once in the idle state, /two/ AUTO REFRESH cycles must be + * performed. After the AUTO REFRESH cycles are complete, the + * SDRAM is ready for mode register programming." + * + * (/emphasis/ mine, gvb) + * + * The way I interpret this, Micron start up sequence is: + * 1. Issue a PRECHARGE-BANK command (initial precharge) + * 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged") + * 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands + * 4. Issue a MODE-SET command to initialize the mode register + * + * -------- + * + * The initial commands are executed by setting P/LSDMR[OP] and + * accessing the SDRAM with a single-byte transaction." + * + * The appropriate BRx/ORx registers have already been set when we + * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE. + */ +#if 1 + memctl->memc_mptpr = CFG_MPTPR; + memctl->memc_psrt = psrt; + + memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; + for (i = 0; i < 8; i++) + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN; + *ramaddr = c; + + /* + * Do it a second time for the second set of chips if the DIMM has + * two chip selects (double sided). + */ + if(chipselects > 1) + { + ramaddr += sdram_size; + + memctl->memc_br3 = CFG_BR3_PRELIM + sdram_size; + memctl->memc_or3 = or; + + memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; + for (i = 0; i < 8; i++) + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; + *ramaddr = c; + + memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN; + *ramaddr = c; + } +#endif + /* + printf("memctl->memc_mptpr = 0x%08x\n", CFG_MPTPR); + printf("memctl->memc_psrt = 0x%08x\n", psrt); + + printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_PREA); + printf("ramaddr = 0x%08x\n", ramaddr); + + printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_CBRR); + + printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_MRW); + + printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_NORM | PSDMR_RFEN); + + immap->im_siu_conf.sc_ppc_acr = 0x00000002; + immap->im_siu_conf.sc_ppc_alrh = 0x01267893; + immap->im_siu_conf.sc_tescr1 = 0x00004000; + */ +#if 0 + /* init sdram dimm */ + ramaddr = (uchar *)CFG_SDRAM_BASE; + memctl->memc_psrt = 0x00000010; + immap->im_memctl.memc_or2 = 0xFF000CA0; + immap->im_memctl.memc_br2 = 0x00000041; + memctl->memc_psdmr = 0x296EB452; + *ramaddr = c; + memctl->memc_psdmr = 0x096EB452; + for (i = 0; i < 8; i++) + *ramaddr = c; + + memctl->memc_psdmr = 0x196EB452; + *ramaddr = c; + memctl->memc_psdmr = 0x416EB452; + *ramaddr = c; +#endif + /* print info */ + printf("SDRAM configuration read from SPD\n"); + printf("\tSize per side = %dMB\n", sdram_size >> 20); + printf("\tOrganization: %d sides, %d banks, %d Columns, %d Rows, Data width = %d bits\n", chipselects, 1<<(banks), cols, rows, data_width); + printf("\tRefresh rate = %d, CAS latency = %d\n", psrt, caslatency); + printf("\tTotal size: "); + + return (sdram_size * chipselects); + /*return (16 * 1024 * 1024);*/ +} diff --git a/board/mpc8266ads/u-boot.lds b/board/mpc8266ads/u-boot.lds new file mode 100644 index 0000000000..671e70db88 --- /dev/null +++ b/board/mpc8266ads/u-boot.lds @@ -0,0 +1,117 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc8260/start.o (.text) + *(.text) + *(.fixup) + *(.got1) + . = ALIGN(16); + *(.rodata) + *(.rodata1) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} + diff --git a/board/w7o/init.S b/board/w7o/init.S index 0abf21fe86..511a1bb52e 100644 --- a/board/w7o/init.S +++ b/board/w7o/init.S @@ -162,6 +162,7 @@ sdram_init: * contents of the SPD EEPROM. If the SPD EEPROM is blank or * erronious, spd_sdram returns 0 in R3. */ + li r3,0 bl spd_sdram addic. r3, r3, 0 /* Check for error, save dram size */ bne ..sdri_done /* If it worked, we're done... */ diff --git a/board/walnut405/walnut405.c b/board/walnut405/walnut405.c index 93c2034328..598509f7c2 100644 --- a/board/walnut405/walnut405.c +++ b/board/walnut405/walnut405.c @@ -20,13 +20,11 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ -long int spd_sdram (void); #include #include "walnut405.h" #include - - +#include int board_pre_init (void) { @@ -118,11 +116,8 @@ int checkboard (void) the necessary info for SDRAM controller configuration ------------------------------------------------------------------------- */ long int initdram (int board_type) -{ - long int ret; - - ret = spd_sdram (); - return ret; +{ + return spd_sdram (0); } /* ------------------------------------------------------------------------- */ diff --git a/cpu/ppc4xx/spd_sdram.c b/cpu/ppc4xx/spd_sdram.c index fc0c980c73..bf5d22429d 100644 --- a/cpu/ppc4xx/spd_sdram.c +++ b/cpu/ppc4xx/spd_sdram.c @@ -4,8 +4,8 @@ * * Based on code by: * - * Kenneth Johansson ,Ericsson Business Innovation. - * kenneth.johansson@inn.ericsson.se + * Kenneth Johansson ,Ericsson AB. + * kenneth.johansson@etx.ericsson.se * * hacked up by bill hunter. fixed so we could run before * serial_init and console_init. previous version avoided this by @@ -87,25 +87,16 @@ #define SDRAM0_BXCR_SZ(x) ( (( x << SDRAM0_BXCR_SZ_SHIFT) & SDRAM0_BXCR_SZ_MASK) ) #define SDRAM0_BXCR_AM(x) ( (( x << SDRAM0_BXCR_AM_SHIFT) & SDRAM0_BXCR_AM_MASK) ) -#ifdef CONFIG_W7O +#ifdef CONFIG_SPDDRAM_SILENT # define SPD_ERR(x) do { return 0; } while (0) #else -# define SPD_ERR(x) do { printf(x); hang(); } while (0) +# define SPD_ERR(x) do { printf(x); return(0); } while (0) #endif -/* - * what we really want is - * (1/hertz) but we don't want to use floats so multiply with 10E9 - * - * The error needs to be on the safe side so we want the floor function. - * This means we get an exact value or we calculate that our bus frequency is - * a bit faster than it really is and thus we don't progam the sdram controller - * to run to fast - */ #define sdram_HZ_to_ns(hertz) (1000000000/(hertz)) /* function prototypes */ -int spd_read(uint addr); /* prototype */ +int spd_read(uint addr); /* @@ -114,17 +105,17 @@ int spd_read(uint addr); /* prototype */ * * This works on boards that has the same schematics that the IBM walnut has. * - * BUG: Don't handle ECC memory - * BUG: A few values in the TR register is currently hardcoded + * Input: null for default I2C spd functions or a pointer to a custom function + * returning spd_data. */ -long int spd_sdram(void) +long int spd_sdram(int(read_spd)(uint addr)) { int bus_period,tmp,row,col; int total_size,bank_size,bank_code; int ecc_on; - int mode = 4; - int bank_cnt = 1; + int mode; + int bank_cnt; int sdram0_pmit=0x07c00000; int sdram0_besr0=-1; @@ -144,14 +135,19 @@ long int spd_sdram(void) int t_rp; int t_rcd; - int t_rc = 70; /* This value not available in SPD_EEPROM */ - int min_cas = 2; + int t_ras; + int t_rc; + int min_cas; + if(read_spd == 0){ + read_spd=spd_read; /* * Make sure I2C controller is initialized * before continuing. */ - i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); + i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); + } + /* * Calculate the bus period, we do it this @@ -162,7 +158,7 @@ long int spd_sdram(void) bus_period = sdram_HZ_to_ns(tmp); /* get sdram speed */ /* Make shure we are using SDRAM */ - if (spd_read(2) != 0x04){ + if (read_spd(2) != 0x04){ SPD_ERR("SDRAM - non SDRAM memory module found\n"); } @@ -180,34 +176,35 @@ long int spd_sdram(void) * use the min supported mode */ - tmp = spd_read(127) & 0x6; + tmp = read_spd(127) & 0x6; if(tmp == 0x02){ /* only cas = 2 supported */ min_cas = 2; -/* t_ck = spd_read(9); */ -/* t_ac = spd_read(10); */ +/* t_ck = read_spd(9); */ +/* t_ac = read_spd(10); */ } else if (tmp == 0x04){ /* only cas = 3 supported */ min_cas = 3; -/* t_ck = spd_read(9); */ -/* t_ac = spd_read(10); */ +/* t_ck = read_spd(9); */ +/* t_ac = read_spd(10); */ } else if (tmp == 0x06){ /* 2,3 supported, so use 2 */ min_cas = 2; -/* t_ck = spd_read(23); */ -/* t_ac = spd_read(24); */ +/* t_ck = read_spd(23); */ +/* t_ac = read_spd(24); */ } else { SPD_ERR("SDRAM - unsupported CAS latency \n"); } - /* get some timing values, t_rp,t_rcd + /* get some timing values, t_rp,t_rcd,t_ras,t_rc */ - t_rp = spd_read(27); - t_rcd = spd_read(29); - + t_rp = read_spd(27); + t_rcd = read_spd(29); + t_ras = read_spd(30); + t_rc = t_ras + t_rp; /* The following timing calcs subtract 1 before deviding. - * this has effect of using ceiling intead of floor rounding, + * this has effect of using ceiling instead of floor rounding, * and also subtracting 1 to convert number to reg value */ /* set up CASL */ @@ -216,12 +213,12 @@ long int spd_sdram(void) sdram0_tr |= (((t_rp - 1)/bus_period) & 0x3) << SDRAM0_TR_PTA_SHIFT; /* set up CTP */ tmp = ((t_rc - t_rcd - t_rp -1) / bus_period) & 0x3; - if(tmp<1) SPD_ERR("SDRAM - unsupported prech to act time (Trp)\n"); + if(tmp<1) tmp=1; sdram0_tr |= tmp << SDRAM0_TR_CTP_SHIFT; /* set LDF = 2 cycles, reg value = 1 */ sdram0_tr |= 1 << SDRAM0_TR_LDF_SHIFT; /* set RFTA = t_rfc/bus_period, use t_rfc = t_rc */ - tmp = ((t_rc - 1) / bus_period)-4; + tmp = ( (t_rc - 1) / bus_period)-3; if(tmp<0)tmp=0; if(tmp>6)tmp=6; sdram0_tr |= tmp << SDRAM0_TR_RFTA_SHIFT; @@ -232,9 +229,9 @@ long int spd_sdram(void) /*------------------------------------------------------------------ configure RTR register -------------------------------------------------------------------*/ - row = spd_read(3); - col = spd_read(4); - tmp = spd_read(12) & 0x7f ; /* refresh type less self refresh bit */ + row = read_spd(3); + col = read_spd(4); + tmp = read_spd(12) & 0x7f ; /* refresh type less self refresh bit */ switch(tmp){ case 0x00: tmp=15625; @@ -265,9 +262,9 @@ long int spd_sdram(void) determine the number of banks used -------------------------------------------------------------------*/ /* byte 7:6 is module data width */ - if(spd_read(7) != 0) + if(read_spd(7) != 0) SPD_ERR("SDRAM - unsupported module width\n"); - tmp = spd_read(6); + tmp = read_spd(6); if (tmp < 32) SPD_ERR("SDRAM - unsupported module width\n"); else if (tmp < 64) @@ -280,7 +277,7 @@ long int spd_sdram(void) SPD_ERR("SDRAM - unsupported module width\n"); /* byte 5 is the module row count (refered to as dimm "sides") */ - tmp = spd_read(5); + tmp = read_spd(5); if(tmp==1); else if(tmp==2) bank_cnt *=2; else if(tmp==4) bank_cnt *=4; @@ -292,7 +289,7 @@ long int spd_sdram(void) /* now check for ECC ability of module. We only support ECC * on 32 bit wide devices with 8 bit ECC. */ - if ( (spd_read(11)==2) && ((spd_read(6)==40) || (spd_read(14)==8)) ){ + if ( (read_spd(11)==2) && ((read_spd(6)==40) || (read_spd(14)==8)) ){ sdram0_ecccfg=0xf<>1; } - total_size *= spd_read(5); /* mult by module rows (dimm sides) */ + total_size *= read_spd(5); /* mult by module rows (dimm sides) */ /*------------------------------------------------------------------ map rows * cols * banks to a mode @@ -357,7 +354,7 @@ long int spd_sdram(void) break; case 9: case 10: - if (spd_read(17) ==2 ) + if (read_spd(17) ==2 ) mode=6; /* mode 7 */ else mode=2; /* mode 3 */ diff --git a/drivers/pci_auto.c b/drivers/pci_auto.c index 295f7c848d..00177cc282 100644 --- a/drivers/pci_auto.c +++ b/drivers/pci_auto.c @@ -285,34 +285,22 @@ int pciauto_config_device(struct pci_controller *hose, pci_dev_t dev) unsigned int sub_bus = PCI_BUS(dev); unsigned short class; unsigned char prg_iface; - int n; pci_hose_read_config_word(hose, dev, PCI_CLASS_DEVICE, &class); switch(class) { case PCI_CLASS_BRIDGE_PCI: + hose->current_busno++; pciauto_setup_device(hose, dev, 2, hose->pci_mem, hose->pci_io); - DEBUGF("PCI Autoconfig: Found P2P bridge, device %d\n", - PCI_DEV(dev)); - - /* HJF: Make sure two bridges on the same bus - * won't get the same bus number - */ - pciauto_prescan_setup_bridge(hose, dev, - max(sub_bus, hose->current_busno)); - - n = pci_hose_scan_bus(hose, hose->current_busno+1 /*PCI_BUS(dev)+1*/); - sub_bus = max(sub_bus, n); - sub_bus = max(sub_bus, hose->current_busno); + DEBUGF("PCI Autoconfig: Found P2P bridge, device %d\n", PCI_DEV(dev)); + pciauto_prescan_setup_bridge(hose, dev, sub_bus); + + pci_hose_scan_bus(hose, hose->current_busno); - DEBUGF("PCI Autoconfig: Got %d from pci_hose_scan_bus\n", - sub_bus); - - pciauto_postscan_setup_bridge(hose, dev, - max(sub_bus, hose->current_busno)); - hose->current_busno++; + pciauto_postscan_setup_bridge(hose, dev, sub_bus); + sub_bus = hose->current_busno; break; case PCI_CLASS_STORAGE_IDE: diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h index b4d8406aa5..7968c8b2b1 100644 --- a/include/configs/MPC8260ADS.h +++ b/include/configs/MPC8260ADS.h @@ -99,8 +99,17 @@ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F +#if defined(CONFIG_SPD_EEPROM) && !defined(CONFIG_SPD_ADDR) +#define CONFIG_SPD_ADDR 0x50 +#endif + +#ifndef CONFIG_SDRAM_PBI +#define CONFIG_SDRAM_PBI 1 /* By default, use page-based interleaving */ +#endif +#ifndef CONFIG_8260_CLKIN #define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#endif #define CONFIG_BAUDRATE 115200 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \ diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h new file mode 100644 index 0000000000..e72ce0a78a --- /dev/null +++ b/include/configs/MPC8266ADS.h @@ -0,0 +1,411 @@ +/* + * (C) Copyright 2001 + * Stuart Hughes + * This file is based on similar values for other boards found in other + * U-Boot config files, and some that I found in the mpc8260ads manual. + * + * Note: my board is a PILOT rev. + * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Config header file for a MPC8260ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_MPC8260ADS 1 /* ...on motorola ads board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +/* allow serial and ethaddr to be overwritten */ +#define CONFIG_ENV_OVERWRITE + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ + +#if (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers (see 28-13) + * - Half duplex + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR 0 + +#endif /* CONFIG_ETHER_INDEX */ + +/* other options */ +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_EEPROM_ADDR_LEN 1 + +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 + + +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#define CONFIG_BAUDRATE 115200 + + +#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \ + CFG_CMD_BEDBUG | \ + CFG_CMD_BSP | \ + CFG_CMD_DATE | \ + CFG_CMD_DOC | \ + CFG_CMD_DTT | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_FDC | \ + CFG_CMD_FDOS | \ + CFG_CMD_HWFLOW | \ + CFG_CMD_IDE | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_KGDB | \ + CFG_CMD_MII | \ + CFG_CMD_PCI | \ + CFG_CMD_PCMCIA | \ + CFG_CMD_SCSI | \ + CFG_CMD_SPI | \ + CFG_CMD_VFD | \ + CFG_CMD_USB ) ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */ +#define CONFIG_BOOTARGS "root=/dev/ram rw" + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ +#endif + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + /* for versions < 2.4.5-pre5 */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CFG_FLASH_BASE 0xff800000 +#define FLASH_BASE 0xff800000 +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 32 /* max num of sects on one chip */ +#define CFG_FLASH_SIZE 8 +#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ + +#undef CFG_FLASH_CHECKSUM + +/* this is stuff came out of the Motorola docs */ +/* Only change this if you also change the Hardware configuration Word */ +#define CFG_DEFAULT_IMMR 0x0F010000 + +/* +#define CFG_IMMR 0x04700000 +#define CFG_BCSR 0x04500000 +*/ + +/* Set IMMR to 0xF0000000 or above to boot Linux */ +#define CFG_IMMR 0xF0000000 +#define CFG_BCSR 0x04500000 + +/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes + */ +/*#define CONFIG_VERY_BIG_RAM 1*/ + +/* What should be the base address of SDRAM DIMM and how big is + * it (in Mbytes)? This will normally auto-configure via the SPD. +*/ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 16 + +#define SDRAM_SPD_ADDR 0x50 + + +/*----------------------------------------------------------------------- + * BR2,BR3 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR2,OR3 - Option Register + * Ref: Section 10.3.2 on page 10-16 + *----------------------------------------------------------------------- + */ + +/* Bank 2,3 - SDRAM DIMM + */ + +/* The BR2 is configured as follows: + * + * - Base address of 0x00000000 + * - 64 bit port size (60x bus only) + * - Data errors checking is disabled + * - Read and write access + * - SDRAM 60x bus + * - Access are handled by the memory controller according to MSEL + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + */ +#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_BR3_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +/* With a 64 MB DIMM, the OR2 is configured as follows: + * + * - 64 MB + * - 4 internal banks per device + * - Row start address bit is A8 with PSDMR[PBI] = 0 + * - 12 row address lines + * - Back-to-back page mode + * - Internal bank interleaving within save device enabled + */ +#if (CFG_SDRAM_SIZE == 64) +#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A8 |\ + ORxS_NUMR_12) +#elif (CFG_SDRAM_SIZE == 16) +#define CFG_OR2_PRELIM (0xFF000CA0) +#else +#error "INVALID SDRAM CONFIGURATION" +#endif + +/*----------------------------------------------------------------------- + * PSDMR - 60x Bus SDRAM Mode Register + * Ref: Section 10.3.3 on page 10-21 + *----------------------------------------------------------------------- + */ + +#if (CFG_SDRAM_SIZE == 64) +/* With a 64 MB DIMM, the PSDMR is configured as follows: + * + * - Bank Based Interleaving, + * - Refresh Enable, + * - Address Multiplexing where A5 is output on A14 pin + * (A6 on A15, and so on), + * - use address pins A14-A16 as bank select, + * - A9 is output on SDA10 during an ACTIVATE command, + * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, + * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command + * is 3 clocks, + * - earliest timing for READ/WRITE command after ACTIVATE command is + * 2 clocks, + * - earliest timing for PRECHARGE after last data was read is 1 clock, + * - earliest timing for PRECHARGE after last data was written is 1 clock, + * - CAS Latency is 2. + */ +#define CFG_PSDMR (PSDMR_RFEN |\ + PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A14_A16 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_3W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) +#elif (CFG_SDRAM_SIZE == 16) +/* With a 16 MB DIMM, the PSDMR is configured as follows: + * + * configuration parameters found in Motorola documentation + */ +#define CFG_PSDMR (0x016EB452) +#else +#error "INVALID SDRAM CONFIGURATION" +#endif + + +#define RS232EN_1 0x02000002 +#define RS232EN_2 0x01000001 +#define FETHIEN 0x08000008 +#define FETH_RST 0x04000004 + +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + +/* 0x0EA28205 */ +/*#define CFG_HRCW_MASTER ( ( HRCW_BPS11 | HRCW_CIP ) |\ + ( HRCW_L2CPC10 | HRCW_DPPC10 | HRCW_ISB010 ) |\ + ( HRCW_BMS | HRCW_APPC10 ) |\ + ( HRCW_MODCK_H0101 ) \ + ) +*/ + +/* This value should actually be situated in the first 256 bytes of the FLASH + which on the standard MPC8266ADS board is at address 0xFF800000 + The linker script places it at 0xFFF00000 instead. + + It still works, however, as long as the ADS board jumper JP3 is set to + position 2-3 so the board is using the BCSR as Hardware Configuration Word + + If you want to use the one defined here instead, ust copy the first 256 bytes from + 0xfff00000 to 0xff800000 (for 8MB flash) + + - Rune + + */ +#define CFG_HRCW_MASTER 0x0cb23645 + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#ifndef CFG_RAMBOOT +# define CFG_ENV_IS_IN_FLASH 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +# define CFG_ENV_SECT_SIZE 0x40000 +#else +# define CFG_ENV_IS_IN_NVRAM 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +# define CFG_ENV_SIZE 0x200 +#endif /* CFG_RAMBOOT */ + + +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + + +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE ) + +#define CFG_HID2 0 + +#define CFG_SYPCR 0xFFFFFFC3 +#define CFG_BCR 0x100C0000 +#define CFG_SIUMCR 0x0A200000 +#define CFG_SCCR 0x00000000 +#define CFG_BR0_PRELIM 0xFF801801 +#define CFG_OR0_PRELIM 0xFF800836 +#define CFG_BR1_PRELIM 0x04501801 +#define CFG_OR1_PRELIM 0xFFFF8010 + +#define CFG_RMR 0 +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) +#define CFG_RCCR 0 +/*#define CFG_PSDMR 0x016EB452*/ +#define CFG_MPTPR 0x00001900 +#define CFG_PSRT 0x00000021 + +#define CFG_RESET_ADDRESS 0x04400000 + +#endif /* __CONFIG_H */ diff --git a/include/configs/TOP860.h b/include/configs/TOP860.h new file mode 100644 index 0000000000..f902685b32 --- /dev/null +++ b/include/configs/TOP860.h @@ -0,0 +1,439 @@ +/* + * (C) Copyright 2003 + * EMK Elektronik GmbH + * Reinhard Meyer + * + * Configuation settings for the TOP860 board. + * + * ----------------------------------------------------------------- + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +/* + * TOP860 is a simple module: + * 16-bit wide FLASH on CS0 (2MB or more) + * 32-bit wide DRAM on CS2 (either 4MB or 16MB) + * FEC with Am79C874 100-Base-T and Fiber Optic + * Ports available, but we choose SMC1 for Console + * 8k I2C EEPROM at address 0xae, 6k user available, 2k factory set + * 32768Hz crystal PLL set for 49.152MHz Core and 24.576MHz Bus Clock + * + * This config has been copied from MBX.h / MBX860T.h + */ +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +/*----------------------------------------------------------------------- + * CPU and BOARD type + */ +#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ +#define CONFIG_MPC860T 1 /* even better... an FEC! */ +#define CONFIG_TOP860 1 /* ...on a TOP860 module */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_IDENT_STRING " EMK TOP860" + +/*----------------------------------------------------------------------- + * CLOCK settings + */ +#define CONFIG_SYSCLK 49152000 +#define CFG_XTAL 32768 +#define CONFIG_EBDF 1 +#define CONFIG_COM 3 +#define CONFIG_RTC_MPC8xx + +/*----------------------------------------------------------------------- + * Physical memory map as defined by EMK + */ +#define CFG_IMMR 0xFFF00000 /* Internal Memory Mapped Register */ +#define CFG_FLASH_BASE 0x80000000 /* FLASH in final mapping */ +#define CFG_DRAM_BASE 0x00000000 /* DRAM in final mapping */ +#define CFG_FLASH_MAX 0x00400000 /* max FLASH to expect */ +#define CFG_DRAM_MAX 0x01000000 /* max DRAM to expect */ + +/*----------------------------------------------------------------------- + * derived values + */ +#define CFG_MF (CONFIG_SYSCLK/CFG_XTAL) +#define CFG_CPUCLOCK CONFIG_SYSCLK +#define CFG_BRGCLOCK CONFIG_SYSCLK +#define CFG_BUSCLOCK (CONFIG_SYSCLK >> CONFIG_EBDF) +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_8xx_GCLK_FREQ CONFIG_SYSCLK + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_CFI + +/*----------------------------------------------------------------------- + * Command interpreter + */ +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#define CONFIG_BAUDRATE 9600 + +/* + * Allow partial commands to be matched to uniqueness. + */ +#define CFG_MATCH_PARTIAL_CMD + +/* + * List of available monitor commands. Use the system default list + * plus add some of the "non-standard" commands back in. + * See ./cmd_confdefs.h + */ +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM | \ + CFG_CMD_REGINFO | \ + CFG_CMD_IMMAP | \ + CFG_CMD_ELF | \ + CFG_CMD_DATE | \ + CFG_CMD_MII | \ + CFG_CMD_BEDBUG \ + ) + +#define CONFIG_AUTOSCRIPT 1 +#define CFG_LOADS_BAUD_CHANGE 1 +#undef CONFIG_LOADS_ECHO /* NO echo on for serial download */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#undef CFG_HUSH_PARSER /* Hush parse for U-Boot */ + +#ifdef CFG_HUSH_PARSER + #define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +/*----------------------------------------------------------------------- + * Memory Test Command + */ +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +/*----------------------------------------------------------------------- + * Environment handler + * only the first 6k in EEPROM are available for user. Of that we use 256b + */ +#define CONFIG_SOFT_I2C +#define CFG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ +#define CFG_ENV_OFFSET 0x1000 +#define CFG_ENV_SIZE 0x0700 +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_FACT_OFFSET 0x1800 +#define CFG_FACT_SIZE 0x0800 +#define CFG_I2C_FACT_ADDR 0x57 +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_SIZE 0x2000 +#define CFG_I2C_SPEED 100000 +#define CFG_I2C_SLAVE 0xFE +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 +#define CONFIG_ENV_OVERWRITE +#define CONFIG_MISC_INIT_R + +#if defined (CONFIG_SOFT_I2C) +#define SDA 0x00010 +#define SCL 0x00020 +#define DIR immr->im_cpm.cp_pbdir +#define DAT immr->im_cpm.cp_pbdat +#define PAR immr->im_cpm.cp_pbpar +#define ODR immr->im_cpm.cp_pbodr +#define I2C_INIT {PAR&=~(SDA|SCL);ODR&=~(SDA|SCL);DAT|=(SDA|SCL);DIR|=(SDA|SCL);} +#define I2C_READ ((DAT&SDA)?1:0) +#define I2C_SDA(x) {if(x)DAT|=SDA;else DAT&=~SDA;} +#define I2C_SCL(x) {if(x)DAT|=SCL;else DAT&=~SCL;} +#define I2C_DELAY {udelay(5);} +#define I2C_ACTIVE {DIR|=SDA;} +#define I2C_TRISTATE {DIR&=~SDA;} +#endif + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/*----------------------------------------------------------------------- + * defines we need to get FEC running + */ +#define CONFIG_NET_MULTI 1 /* the only way to get the FEC in */ +#define CONFIG_FEC_ENET 1 /* Ethernet only via FEC */ +#define FEC_ENET 1 /* eth.c needs it that way... */ +#define CFG_DISCOVER_PHY 1 +#define CONFIG_MII 1 +#define CONFIG_PHY_ADDR 31 + +/*----------------------------------------------------------------------- + * adresses + */ +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x80000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2f00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */ +#define CFG_INIT_VPD_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_VPD_SIZE) +#define CFG_INIT_SP_OFFSET (CFG_INIT_VPD_OFFSET-8) + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/*----------------------------------------------------------------------- + * Debug Enable Register + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 /* used in start.S */ + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * set up PLPRCR (PLL, Low-Power, and Reset Control Register) + * 12 MF calculated Multiplication factor + * 4 0 0000 + * 1 SPLSS 0 System PLL lock status sticky + * 1 TEXPS 1 Timer expired status + * 1 0 0 + * 1 TMIST 0 Timers interrupt status + * 1 0 0 + * 1 CSRC 0 Clock source (0=DFNH, 1=DFNL) + * 2 LPM 00 Low-power modes + * 1 CSR 0 Checkstop reset enable + * 1 LOLRE 0 Loss-of-lock reset enable + * 1 FIOPD 0 Force I/O pull down + * 5 0 00000 + */ +#define CFG_PLPRCR (PLPRCR_TEXPS | ((CFG_MF-1)<<20)) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * set up SYPCR: + * 16 SWTC 0xffff Software watchdog timer count + * 8 BMT 0xff Bus monitor timing + * 1 BME 1 Bus monitor enable + * 3 0 000 + * 1 SWF 1 Software watchdog freeze + * 1 SWE 0/1 Software watchdog enable + * 1 SWRI 0/1 Software watchdog reset/interrupt select (1=HRESET) + * 1 SWP 0/1 Software watchdog prescale (1=/2048) + */ +#if defined (CONFIG_WATCHDOG) + #define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else + #define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * set up SIUMCR + * 1 EARB 0 External arbitration + * 3 EARP 000 External arbitration request priority + * 4 0 0000 + * 1 DSHW 0 Data show cycles + * 2 DBGC 00 Debug pin configuration + * 2 DBPC 00 Debug port pins configuration + * 1 0 0 + * 1 FRC 0 FRZ pin configuration + * 1 DLK 0 Debug register lock + * 1 OPAR 0 Odd parity + * 1 PNCS 0 Parity enable for non memory controller regions + * 1 DPC 0 Data parity pins configuration + * 1 MPRE 0 Multiprocessor reservation enable + * 2 MLRC 11 Multi level reservation control (00=IRQ4, 01=3State, 10=KR/RETRY, 11=SPKROUT) + * 1 AEME 0 Async external master enable + * 1 SEME 0 Sync external master enable + * 1 BSC 0 Byte strobe configuration + * 1 GB5E 0 GPL_B5 enable + * 1 B2DD 0 Bank 2 double drive + * 1 B3DD 0 Bank 3 double drive + * 4 0 0000 + */ +#define CFG_SIUMCR (SIUMCR_MLRC11) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * set up SCCR (System Clock and Reset Control Register) + * 1 0 0 + * 2 COM 11 Clock output module (00=full, 01=half, 11=off) + * 3 0 000 + * 1 TBS 1 Timebase source (0=OSCCLK, 1=GCLK2) + * 1 RTDIV 0 Real-time clock divide (0=/4, 1=/512) + * 1 RTSEL 0 Real-time clock select (0=OSCM, 1=EXTCLK) + * 1 CRQEN 0 CPM request enable + * 1 PRQEN 0 Power management request enable + * 2 0 00 + * 2 EBDF xx External bus division factor + * 2 0 00 + * 2 DFSYNC 00 Division factor for SYNCLK + * 2 DFBRG 00 Division factor for BRGCLK + * 3 DFNL 000 Division factor low frequency + * 3 DFNH 000 Division factor high frequency + * 5 0 00000 + */ +#define SCCR_MASK 0 +#if CONFIG_EBDF + #define CFG_SCCR (SCCR_COM11 | SCCR_TBS | SCCR_EBDF01) +#else + #define CFG_SCCR (SCCR_COM11 | SCCR_TBS) +#endif + +/*----------------------------------------------------------------------- + * Chip Select 0 - FLASH + *----------------------------------------------------------------------- + * Preliminary Values + */ +/* FLASH timing: CSNT=1 ACS=10 BIH=1 SCY=4 SETA=0 TLRX=1 EHTR=1 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_4_CLK | OR_TRLX | OR_EHTR) +#define CFG_OR0_PRELIM (-CFG_FLASH_MAX | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V ) + +/*----------------------------------------------------------------------- + * misc + *----------------------------------------------------------------------- + * + */ +/* + * Set the autoboot delay in seconds. A delay of -1 disables autoboot + */ +#define CONFIG_BOOTDELAY 5 + +/* + * Pass the clock frequency to the Linux kernel in units of MHz + */ +#define CONFIG_CLOCKS_IN_MHZ + +#define CONFIG_PREBOOT \ + "echo;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +/* + * BOOTP options + */ +#undef CONFIG_BOOTP_MASK +#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE \ + ) + + +/* + * Set default IP stuff just to get bootstrap entries into the + * environment so that we can autoscript the full default environment. + */ +#define CONFIG_ETHADDR 9a:52:63:15:85:25 +#define CONFIG_SERVERIP 10.0.4.200 +#define CONFIG_IPADDR 10.0.4.111 + +/*----------------------------------------------------------------------- + * Defaults for Autoscript + */ +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ +#define CFG_TFTP_LOADADDR 0x00100000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + + +#endif /* __CONFIG_H */ diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h index 1b867e056d..b5610c9506 100644 --- a/include/configs/W7OLMC.h +++ b/include/configs/W7OLMC.h @@ -81,7 +81,7 @@ #define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ #define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ - +#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ /* * Miscellaneous configurable options */ diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h index 0c06e9181f..89373b9040 100644 --- a/include/configs/W7OLMG.h +++ b/include/configs/W7OLMG.h @@ -87,7 +87,7 @@ #define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ #define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ - +#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ /* * Miscellaneous configurable options */ diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h index 187c33f294..87282acc39 100644 --- a/include/configs/lubbock.h +++ b/include/configs/lubbock.h @@ -70,12 +70,13 @@ #include #define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600" #define CONFIG_ETHADDR 08:00:3e:26:0a:5b #define CONFIG_NETMASK 255.255.0.0 #define CONFIG_IPADDR 192.168.0.21 #define CONFIG_SERVERIP 192.168.0.250 -#define CONFIG_BOOTCOMMAND "FIXME" +#define CONFIG_BOOTCOMMAND "bootm 40000" +#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200" +#define CONFIG_CMDLINE_TAG #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ @@ -100,7 +101,7 @@ #define CFG_LOAD_ADDR 0xa8000000 /* default load address */ #define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ -#define CFG_CPUSPEED 0x141 /* set core clock to 200/200/100 MHz */ +#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */ /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } @@ -130,8 +131,10 @@ #define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ #define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ -#define PHYS_FLASH_2 0x04000000 /* Flash Bank #1 */ +#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */ #define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */ +#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */ +#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ #define CFG_DRAM_BASE 0xa0000000 #define CFG_DRAM_SIZE 0x04000000 @@ -168,8 +171,7 @@ #define CFG_MSC1_VAL 0x3FF1A441 #define CFG_MSC2_VAL 0x7FF17FF1 #define CFG_MDCNFG_VAL 0x00001AC9 -#define CFG_MDREFR_VAL 0x000BC018 -#define CFG_MDREFR_VAL_100 0x00018018 +#define CFG_MDREFR_VAL 0x00018018 #define CFG_MDMRS_VAL 0x00000000 /* @@ -193,8 +195,8 @@ #define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ /* timeout values are in ticks */ -#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */ -#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */ +#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */ /* FIXME */ #define CFG_ENV_IS_IN_FLASH 1 diff --git a/include/spd.h b/include/spd.h new file mode 100644 index 0000000000..1ad4d801f5 --- /dev/null +++ b/include/spd.h @@ -0,0 +1,78 @@ +/* + * Copyright (C) 2003 Arabella Software Ltd. + * Yuli Barcohen + * + * Serial Presence Detect (SPD) EEPROM format according to the + * Intel's PC SDRAM Serial Presence Detect (SPD) Specification, + * revision 1.2B, November 1999 + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef _SPD_H_ +#define _SPD_H_ + +typedef struct spd_eeprom_s { + unsigned char info_size; /* # of bytes written into serial memory */ + unsigned char chip_size; /* Total # of bytes of SPD memory device */ + unsigned char mem_type; /* Fundamental memory type (FPM, EDO, SDRAM...) */ + unsigned char nrow_addr; /* # of Row Addresses on this assembly */ + unsigned char ncol_addr; /* # of Column Addresses on this assembly */ + unsigned char nrows; /* # of Module Rows on this assembly */ + unsigned char dataw_lsb; /* Data Width of this assembly */ + unsigned char dataw_msb; /* ... Data Width continuation */ + unsigned char voltage; /* Voltage interface standard of this assembly */ + unsigned char clk_cycle; /* SDRAM Cycle time at CL=X */ + unsigned char clk_access; /* SDRAM Access from Clock at CL=X */ + unsigned char config; /* DIMM Configuration type (non-parity, ECC) */ + unsigned char refresh; /* Refresh Rate/Type */ + unsigned char primw; /* Primary SDRAM Width */ + unsigned char ecw; /* Error Checking SDRAM width */ + unsigned char min_delay; /* Min Clock Delay for Back to Back Random Address */ + unsigned char burstl; /* Burst Lengths Supported */ + unsigned char nbanks; /* # of Banks on Each SDRAM Device */ + unsigned char cas_lat; /* CAS# Latencies Supported */ + unsigned char cs_lat; /* CS# Latency */ + unsigned char write_lat; /* Write Latency (also called Write Recovery time) */ + unsigned char mod_attr; /* SDRAM Module Attributes */ + unsigned char dev_attr; /* SDRAM Device Attributes */ + unsigned char clk_cycle2; /* Min SDRAM Cycle time at CL=X-1 */ + unsigned char clk_access2; /* SDRAM Access from Clock at CL=X-1 */ + unsigned char clk_cycle3; /* Min SDRAM Cycle time at CL=X-2 */ + unsigned char clk_access3; /* Max SDRAM Access from Clock at CL=X-2 */ + unsigned char trp; /* Min Row Precharge Time (tRP) */ + unsigned char trrd; /* Min Row Active to Row Active (tRRD) */ + unsigned char trcd; /* Min RAS to CAS Delay (tRCD) */ + unsigned char tras; /* Minimum RAS Pulse Width (tRAS) */ + unsigned char row_dens; /* Density of each row on module */ + unsigned char ca_setup; /* Command and Address signal input setup time */ + unsigned char ca_hold; /* Command and Address signal input hold time */ + unsigned char data_setup; /* Data signal input setup time */ + unsigned char data_hold; /* Data signal input hold time */ + unsigned char sset[26]; /* Superset Information (may be used in future) */ + unsigned char spd_rev; /* SPD Data Revision Code */ + unsigned char cksum; /* Checksum for bytes 0-62 */ + unsigned char mid[8]; /* Manufacturer's JEDEC ID code per JEP-108E */ + unsigned char mloc; /* Manufacturing Location */ + unsigned char mpart[18]; /* Manufacturer's Part Number */ + unsigned char rev[2]; /* Revision Code */ + unsigned char mdate[2]; /* Manufacturing Date */ + unsigned char sernum[4]; /* Assembly Serial Number */ + unsigned char mspec[27]; /* Manufacturer Specific Data */ + unsigned char freq; /* Intel specification frequency */ + unsigned char intel_cas; /* Intel Specification CAS# Latency support */ +} spd_eeprom_t; + +#endif /* _SPD_H_ */ diff --git a/include/spd_sdram.h b/include/spd_sdram.h new file mode 100644 index 0000000000..feb1bbd4c5 --- /dev/null +++ b/include/spd_sdram.h @@ -0,0 +1,6 @@ +#ifndef _SPD_SDRAM_H_ +#define _SPD_SDRAM_H_ + +long int spd_sdram(int(read_spd)(uint addr)); + +#endif