From: Georgi Vlaev Date: Fri, 28 Dec 2018 08:24:01 +0000 (+0200) Subject: ath79: add support for TP-Link Archer C6 v2 X-Git-Tag: v19.07.0-rc1~1696 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=d03aae1a09fce5a5d5747855bc07ee1f54388e03;p=oweals%2Fopenwrt.git ath79: add support for TP-Link Archer C6 v2 This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev --- diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 87c9c29624..fa7fe7178f 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -76,6 +76,10 @@ tplink,archer-c59-v1) ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E" ucidef_set_led_netdev "wan" "WAN" "tp-link:green:wan" "eth0" ;; +tplink,archer-c6-v2) + ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x3C" + ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02" + ;; tplink,re450-v2) ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx" ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link" diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 33166079e7..e24c58e208 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -154,6 +154,7 @@ ath79_setup_interfaces() "0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; tplink,archer-a7-v5|\ + tplink,archer-c6-v2|\ tplink,archer-c7-v5|\ tplink,tl-wdr3600|\ tplink,tl-wdr4300) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index d9ce0c9f9f..441893a752 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -155,7 +155,8 @@ case "$FIRMWARE" in /lib/firmware/ath10k/QCA9888/hw2.0/board.bin ;; tplink,archer-c58-v1|\ - tplink,archer-c59-v1) + tplink,archer-c59-v1|\ + tplink,archer-c6-v2) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mac 8) -1) ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts new file mode 100644 index 0000000000..5caec6fab1 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9563_tplink_archer-x6-v2.dtsi" + +/ { + compatible = "tplink,archer-c6-v2", "qca,qca9563"; + model = "TP-Link Archer C6 v2"; +}; diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi new file mode 100644 index 0000000000..37ab16453b --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi @@ -0,0 +1,170 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + leds { + compatible = "gpio-leds"; + + power: power { + label = "tp-link:green:power"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan2g { + label = "tp-link:green:wlan2g"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "tp-link:green:wlan5g"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + lan { + label = "tp-link:green:lan"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "tp-link:green:wan"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + + wan_fail { + label = "tp-link:amber:wan"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "tp-link:green:wps"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&gpio { + status = "okay"; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + mac: partition@20000 { + label = "mac"; + reg = <0x020000 0x010000>; + read-only; + }; + + partition@30000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x030000 0x7a0000>; + }; + + partition@7d0000 { + label = "tplink"; + reg = <0x7d0000 0x020000>; + read-only; + }; + + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "sgmii"; + mtd-mac-address = <&mac 0x8>; + phy-handle = <&phy0>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&mac 0x8>; +}; diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index 093ac7293d..be755c7ec0 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -34,6 +34,16 @@ define Device/tplink_archer-c59-v1 endef TARGET_DEVICES += tplink_archer-c59-v1 +define Device/tplink_archer-c6-v2 + $(Device/tplink-safeloader-uimage) + ATH_SOC := qca9563 + IMAGE_SIZE := 7808k + DEVICE_TITLE := TP-LINK Archer C6 v2 + TPLINK_BOARD_ID := ARCHER-C6-V2 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct +endef +TARGET_DEVICES += tplink_archer-c6-v2 + define Device/tplink_archer-c7-v1 $(Device/tplink-8mlzma) ATH_SOC := qca9558 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 358247e626..74ea697634 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -548,6 +548,42 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system", }, + /** Firmware layout for the C6v2 */ + { + .id = "ARCHER-C6-V2", + .vendor = "", + .support_list = + "SupportList:\r\n" + "{product_name:Archer C6,product_ver:2.0.0,special_id:45550000}\r\n" + "{product_name:Archer C6,product_ver:2.0.0,special_id:52550000}\r\n" + "{product_name:Archer C6,product_ver:2.0.0,special_id:4A500000}\r\n", + .support_trail = '\x00', + .soft_ver = "soft_ver:1.0.0\n", + + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"default-mac", 0x20000, 0x00200}, + {"pin", 0x20200, 0x00100}, + {"product-info", 0x20300, 0x00200}, + {"device-id", 0x20500, 0x0fb00}, + {"firmware", 0x30000, 0x7a9400}, + {"soft-version", 0x7d9400, 0x00100}, + {"extra-para", 0x7d9500, 0x00100}, + {"support-list", 0x7d9600, 0x00200}, + {"profile", 0x7d9800, 0x03000}, + {"default-config", 0x7dc800, 0x03000}, + {"partition-table", 0x7df800, 0x00800}, + {"user-config", 0x7e0000, 0x0c000}, + {"certificate", 0x7ec000, 0x04000}, + {"radio", 0x7f0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system", + }, + + /** Firmware layout for the C60v1 */ { .id = "ARCHER-C60-V1", @@ -1624,6 +1660,9 @@ static void build_image(const char *output, } else if (strcasecmp(info->id, "ARCHER-A7-V5") == 0 || strcasecmp(info->id, "ARCHER-C7-V4") == 0 || strcasecmp(info->id, "ARCHER-C7-V5") == 0) { const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0xca, 0x00, 0x01, 0x00, 0x00}; parts[5] = put_data("extra-para", mdat, 11); + } else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0) { + const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00}; + parts[5] = put_data("extra-para", mdat, 11); } size_t len;