From: William Juul Date: Wed, 31 Oct 2007 12:53:06 +0000 (+0100) Subject: Update MTD to that of Linux 2.6.22.1 X-Git-Tag: v2008.10-rc1~181^2~31 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=cfa460adfdefcc30d104e1a9ee44994ee349bb7b;p=oweals%2Fu-boot.git Update MTD to that of Linux 2.6.22.1 A lot changed in the Linux MTD code, since it was last ported from Linux to U-Boot. This patch takes U-Boot NAND support to the level of Linux 2.6.22.1 and will enable support for very large NAND devices (4KB pages) and ease the compatibility between U-Boot and Linux filesystems. This patch is tested on two custom boards with PPC and ARM processors running YAFFS in U-Boot and Linux using gcc-4.1.2 cross compilers. MAKEALL ppc/arm has some issues: * DOC/OneNand/nand_spl is not building (I have not tried porting these parts, and since I do not have any HW and I am not familiar with this code/HW I think its best left to someone else.) Except for the issues mentioned above, I have ported all drivers necessary to run MAKEALL ppc/arm without errors and warnings. Many drivers were trivial to port, but some were not so trivial. The following drivers must be examined carefully and maybe rewritten to some degree: cpu/ppc4xx/ndfc.c cpu/arm926ejs/davinci/nand.c board/delta/nand.c board/zylonite/nand.c Signed-off-by: William Juul Signed-off-by: Stig Olsen Signed-off-by: Scott Wood --- diff --git a/board/bf537-stamp/nand.c b/board/bf537-stamp/nand.c index 6ff0f4f96c..bdf1d6ee45 100644 --- a/board/bf537-stamp/nand.c +++ b/board/bf537-stamp/nand.c @@ -37,34 +37,29 @@ /* * hardware specific access to control-lines */ -static void bfin_hwcontrol(struct mtd_info *mtd, int cmd) +static void bfin_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { register struct nand_chip *this = mtd->priv; + u32 IO_ADDR_W = (u32) this->IO_ADDR_W; - switch (cmd) { - - case NAND_CTL_SETCLE: - this->IO_ADDR_W = CFG_NAND_BASE + BFIN_NAND_CLE; - break; - case NAND_CTL_CLRCLE: - this->IO_ADDR_W = CFG_NAND_BASE; - break; - - case NAND_CTL_SETALE: - this->IO_ADDR_W = CFG_NAND_BASE + BFIN_NAND_ALE; - break; - case NAND_CTL_CLRALE: - this->IO_ADDR_W = CFG_NAND_BASE; - break; - case NAND_CTL_SETNCE: - case NAND_CTL_CLRNCE: - break; + if (ctrl & NAND_CTRL_CHANGE) { + if( ctrl & NAND_CLE ) + IO_ADDR_W = CFG_NAND_BASE + BFIN_NAND_CLE; + else + IO_ADDR_W = CFG_NAND_BASE; + if( ctrl & NAND_ALE ) + IO_ADDR_W = CFG_NAND_BASE + BFIN_NAND_ALE; + else + IO_ADDR_W = CFG_NAND_BASE; + this->IO_ADDR_W = (void __iomem *) IO_ADDR_W; } - this->IO_ADDR_R = this->IO_ADDR_W; /* Drain the writebuffer */ SSYNC(); + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } int bfin_device_ready(struct mtd_info *mtd) @@ -79,11 +74,11 @@ int bfin_device_ready(struct mtd_info *mtd) * argument are board-specific (per include/linux/mtd/nand.h): * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device - * - hwcontrol: hardwarespecific function for accesing control-lines + * - cmd_ctrl: hardwarespecific function for accesing control-lines * - dev_ready: hardwarespecific function for accesing device ready/busy line * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must * only be provided if a hardware ECC is available - * - eccmode: mode of ecc, see defines + * - ecc.mode: mode of ecc, see defines * - chip_delay: chip dependent delay for transfering data from array to * read regs (tR) * - options: various chip options. They can partly be set to inform @@ -98,8 +93,8 @@ void board_nand_init(struct nand_chip *nand) *PORT(CONFIG_NAND_GPIO_PORT, IO_DIR) &= ~BFIN_NAND_READY; *PORT(CONFIG_NAND_GPIO_PORT, IO_INEN) |= BFIN_NAND_READY; - nand->hwcontrol = bfin_hwcontrol; - nand->eccmode = NAND_ECC_SOFT; + nand->cmd_ctrl = bfin_hwcontrol; + nand->ecc.mode = NAND_ECC_SOFT; nand->dev_ready = bfin_device_ready; nand->chip_delay = 30; } diff --git a/board/dave/PPChameleonEVB/nand.c b/board/dave/PPChameleonEVB/nand.c index 09c0b043e7..4bc4257c88 100644 --- a/board/dave/PPChameleonEVB/nand.c +++ b/board/dave/PPChameleonEVB/nand.c @@ -21,7 +21,7 @@ */ #include - +#include #if defined(CONFIG_CMD_NAND) @@ -31,31 +31,28 @@ * hardware specific access to control-lines * function borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c) */ -static void ppchameleonevb_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void ppchameleonevb_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - struct nand_chip *this = mtdinfo->priv; + struct nand_chip *this = mtd->priv; ulong base = (ulong) this->IO_ADDR_W; - switch(cmd) { - case NAND_CTL_SETCLE: - MACRO_NAND_CTL_SETCLE((unsigned long)base); - break; - case NAND_CTL_CLRCLE: - MACRO_NAND_CTL_CLRCLE((unsigned long)base); - break; - case NAND_CTL_SETALE: - MACRO_NAND_CTL_SETALE((unsigned long)base); - break; - case NAND_CTL_CLRALE: - MACRO_NAND_CTL_CLRALE((unsigned long)base); - break; - case NAND_CTL_SETNCE: - MACRO_NAND_ENABLE_CE((unsigned long)base); - break; - case NAND_CTL_CLRNCE: - MACRO_NAND_DISABLE_CE((unsigned long)base); - break; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + MACRO_NAND_CTL_SETCLE((unsigned long)base); + else + MACRO_NAND_CTL_CLRCLE((unsigned long)base); + if ( ctrl & NAND_ALE ) + MACRO_NAND_CTL_CLRCLE((unsigned long)base); + else + MACRO_NAND_CTL_CLRALE((unsigned long)base); + if ( ctrl & NAND_NCE ) + MACRO_NAND_ENABLE_CE((unsigned long)base); + else + MACRO_NAND_DISABLE_CE((unsigned long)base); } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } @@ -92,11 +89,11 @@ static int ppchameleonevb_device_ready(struct mtd_info *mtdinfo) * argument are board-specific (per include/linux/mtd/nand.h): * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device - * - hwcontrol: hardwarespecific function for accesing control-lines + * - cmd_ctrl: hardwarespecific function for accesing control-lines * - dev_ready: hardwarespecific function for accesing device ready/busy line * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must * only be provided if a hardware ECC is available - * - eccmode: mode of ecc, see defines + * - ecc.mode: mode of ecc, see defines * - chip_delay: chip dependent delay for transfering data from array to * read regs (tR) * - options: various chip options. They can partly be set to inform @@ -108,9 +105,9 @@ static int ppchameleonevb_device_ready(struct mtd_info *mtdinfo) int board_nand_init(struct nand_chip *nand) { - nand->hwcontrol = ppchameleonevb_hwcontrol; + nand->cmd_ctrl = ppchameleonevb_hwcontrol; nand->dev_ready = ppchameleonevb_device_ready; - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; nand->chip_delay = NAND_BIG_DELAY_US; nand->options = NAND_SAMSUNG_LP_OPTIONS; return 0; diff --git a/board/delta/nand.c b/board/delta/nand.c index 5024056bc3..51520f5fb0 100644 --- a/board/delta/nand.c +++ b/board/delta/nand.c @@ -69,7 +69,7 @@ static struct nand_oobinfo delta_oob = { /* * not required for Monahans DFC */ -static void dfc_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void dfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { return; } @@ -110,30 +110,6 @@ static void dfc_write_buf(struct mtd_info *mtd, const u_char *buf, int len) } -/* - * These functions are quite problematic for the DFC. Luckily they are - * not used in the current nand code, except for nand_command, which - * we've defined our own anyway. The problem is, that we always need - * to write 4 bytes to the DFC Data Buffer, but in these functions we - * don't know if to buffer the bytes/half words until we've gathered 4 - * bytes or if to send them straight away. - * - * Solution: Don't use these with Mona's DFC and complain loudly. - */ -static void dfc_write_word(struct mtd_info *mtd, u16 word) -{ - printf("dfc_write_word: WARNING, this function does not work with the Monahans DFC!\n"); -} -static void dfc_write_byte(struct mtd_info *mtd, u_char byte) -{ - printf("dfc_write_byte: WARNING, this function does not work with the Monahans DFC!\n"); -} - -/* The original: - * static void dfc_read_buf(struct mtd_info *mtd, const u_char *buf, int len) - * - * Shouldn't this be "u_char * const buf" ? - */ static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len) { int i=0, j; @@ -168,7 +144,7 @@ static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len) */ static u16 dfc_read_word(struct mtd_info *mtd) { - printf("dfc_write_byte: UNIMPLEMENTED.\n"); + printf("dfc_read_word: UNIMPLEMENTED.\n"); return 0; } @@ -289,9 +265,10 @@ static void dfc_new_cmd(void) /* this function is called after Programm and Erase Operations to * check for success or failure */ -static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this, int state) +static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this) { unsigned long ndsr=0, event=0; + int state = this->state; if(state == FL_WRITING) { event = NDSR_CS0_CMDD | NDSR_CS0_BBD; @@ -439,7 +416,7 @@ static void dfc_gpio_init(void) * - dev_ready: hardwarespecific function for accesing device ready/busy line * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must * only be provided if a hardware ECC is available - * - eccmode: mode of ecc, see defines + * - ecc.mode: mode of ecc, see defines * - chip_delay: chip dependent delay for transfering data from array to * read regs (tR) * - options: various chip options. They can partly be set to inform @@ -561,20 +538,18 @@ int board_nand_init(struct nand_chip *nand) /* wait(10); */ - nand->hwcontrol = dfc_hwcontrol; + nand->cmd_ctrl = dfc_hwcontrol; /* nand->dev_ready = dfc_device_ready; */ - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; nand->options = NAND_BUSWIDTH_16; nand->waitfunc = dfc_wait; nand->read_byte = dfc_read_byte; - nand->write_byte = dfc_write_byte; nand->read_word = dfc_read_word; - nand->write_word = dfc_write_word; nand->read_buf = dfc_read_buf; nand->write_buf = dfc_write_buf; nand->cmdfunc = dfc_cmdfunc; - nand->autooob = &delta_oob; +// nand->autooob = &delta_oob; nand->badblock_pattern = &delta_bbt_descr; return 0; } diff --git a/board/esd/common/esd405ep_nand.c b/board/esd/common/esd405ep_nand.c index 7bf68473d2..4bf81ab4aa 100644 --- a/board/esd/common/esd405ep_nand.c +++ b/board/esd/common/esd405ep_nand.c @@ -30,28 +30,26 @@ /* * hardware specific access to control-lines */ -static void esd405ep_nand_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void esd405ep_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch(cmd) { - case NAND_CTL_SETCLE: - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CLE); - break; - case NAND_CTL_CLRCLE: - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_CLE); - break; - case NAND_CTL_SETALE: - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_ALE); - break; - case NAND_CTL_CLRALE: - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_ALE); - break; - case NAND_CTL_SETNCE: - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_CE); - break; - case NAND_CTL_CLRNCE: - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CE); - break; + struct nand_chip *this = mtd->priv; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CLE); + else + out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_CLE); + if ( ctrl & NAND_ALE ) + out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_ALE); + else + out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_ALE); + if ( ctrl & NAND_NCE ) + out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_NAND_CE); + else + out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_NAND_CE); } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } @@ -77,9 +75,9 @@ int board_nand_init(struct nand_chip *nand) /* * Initialize nand_chip structure */ - nand->hwcontrol = esd405ep_nand_hwcontrol; + nand->cmd_ctrl = esd405ep_nand_hwcontrol; nand->dev_ready = esd405ep_nand_device_ready; - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; nand->chip_delay = NAND_BIG_DELAY_US; nand->options = NAND_SAMSUNG_LP_OPTIONS; return 0; diff --git a/board/freescale/m5329evb/nand.c b/board/freescale/m5329evb/nand.c index 344a614895..f84912e37e 100644 --- a/board/freescale/m5329evb/nand.c +++ b/board/freescale/m5329evb/nand.c @@ -40,36 +40,26 @@ DECLARE_GLOBAL_DATA_PTR; #define SET_ALE 0x08 #define CLR_ALE ~SET_ALE -static void nand_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct nand_chip *this = mtdinfo->priv; - volatile fbcs_t *fbcs = (fbcs_t *) MMAP_FBCS; +/* volatile fbcs_t *fbcs = (fbcs_t *) MMAP_FBCS; TODO: handle wp */ u32 nand_baseaddr = (u32) this->IO_ADDR_W; - switch (cmd) { - case NAND_CTL_SETNCE: - case NAND_CTL_CLRNCE: - break; - case NAND_CTL_SETCLE: - nand_baseaddr |= SET_CLE; - break; - case NAND_CTL_CLRCLE: - nand_baseaddr &= CLR_CLE; - break; - case NAND_CTL_SETALE: - nand_baseaddr |= SET_ALE; - break; - case NAND_CTL_CLRALE: - nand_baseaddr |= CLR_ALE; - break; - case NAND_CTL_SETWP: - fbcs->csmr2 |= FBCS_CSMR_WP; - break; - case NAND_CTL_CLRWP: - fbcs->csmr2 &= ~FBCS_CSMR_WP; - break; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + nand_baseaddr |= SET_CLE; + else + nand_baseaddr &= CLR_CLE; + if ( ctrl & NAND_ALE ) + nand_baseaddr |= SET_ALE; + else + nand_baseaddr &= CLR_ALE; } this->IO_ADDR_W = (void __iomem *)(nand_baseaddr); + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } static void nand_write_byte(struct mtd_info *mtdinfo, u_char byte) @@ -103,8 +93,8 @@ int board_nand_init(struct nand_chip *nand) gpio->podr_timer = 0; nand->chip_delay = 50; - nand->eccmode = NAND_ECC_SOFT; - nand->hwcontrol = nand_hwcontrol; + nand->ecc.mode = NAND_ECC_SOFT; + nand->cmd_ctrl = nand_hwcontrol; nand->read_byte = nand_read_byte; nand->write_byte = nand_write_byte; nand->dev_ready = nand_dev_ready; diff --git a/board/nc650/nand.c b/board/nc650/nand.c index 8617f7445f..faec6053f7 100644 --- a/board/nc650/nand.c +++ b/board/nc650/nand.c @@ -22,7 +22,7 @@ */ #include - +#include #if defined(CONFIG_CMD_NAND) @@ -32,57 +32,49 @@ /* * hardware specific access to control-lines */ -static void nc650_hwcontrol(struct mtd_info *mtd, int cmd) +static void nc650_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct nand_chip *this = mtd->priv; - switch(cmd) { - case NAND_CTL_SETCLE: - this->IO_ADDR_W += 2; - break; - case NAND_CTL_CLRCLE: - this->IO_ADDR_W -= 2; - break; - case NAND_CTL_SETALE: - this->IO_ADDR_W += 1; - break; - case NAND_CTL_CLRALE: - this->IO_ADDR_W -= 1; - break; - case NAND_CTL_SETNCE: - case NAND_CTL_CLRNCE: - /* nop */ - break; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + this->IO_ADDR_W += 2; + else + this->IO_ADDR_W -= 2; + if ( ctrl & NAND_ALE ) + this->IO_ADDR_W += 1; + else + this->IO_ADDR_W -= 1; } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } #elif defined(CONFIG_IDS852_REV2) /* * hardware specific access to control-lines */ -static void nc650_hwcontrol(struct mtd_info *mtd, int cmd) +static void nc650_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct nand_chip *this = mtd->priv; - switch(cmd) { - case NAND_CTL_SETCLE: - *(((volatile __u8 *) this->IO_ADDR_W) + 0xa) = 0; - break; - case NAND_CTL_CLRCLE: - *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0; - break; - case NAND_CTL_SETALE: - *(((volatile __u8 *) this->IO_ADDR_W) + 0x9) = 0; - break; - case NAND_CTL_CLRALE: - *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0; - break; - case NAND_CTL_SETNCE: - *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0; - break; - case NAND_CTL_CLRNCE: - *(((volatile __u8 *) this->IO_ADDR_W) + 0xc) = 0; - break; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + writeb(0, (volatile __u8 *) this->IO_ADDR_W + 0xa); + else + writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x8); + if ( ctrl & NAND_ALE ) + writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x9); + else + writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x8); + if ( ctrl & NAND_NCE ) + writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x8); + else + writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0xc); } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } #else #error Unknown IDS852 module revision @@ -93,11 +85,11 @@ static void nc650_hwcontrol(struct mtd_info *mtd, int cmd) * argument are board-specific (per include/linux/mtd/nand.h): * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device - * - hwcontrol: hardwarespecific function for accesing control-lines + * - cmd_ctrl: hardwarespecific function for accesing control-lines * - dev_ready: hardwarespecific function for accesing device ready/busy line * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must * only be provided if a hardware ECC is available - * - eccmode: mode of ecc, see defines + * - eccm.ode: mode of ecc, see defines * - chip_delay: chip dependent delay for transfering data from array to * read regs (tR) * - options: various chip options. They can partly be set to inform @@ -109,8 +101,8 @@ static void nc650_hwcontrol(struct mtd_info *mtd, int cmd) int board_nand_init(struct nand_chip *nand) { - nand->hwcontrol = nc650_hwcontrol; - nand->eccmode = NAND_ECC_SOFT; + nand->cmd_ctrl = nc650_hwcontrol; + nand->ecc.mode = NAND_ECC_SOFT; nand->chip_delay = 12; /* nand->options = NAND_SAMSUNG_LP_OPTIONS;*/ return 0; diff --git a/board/netstar/nand.c b/board/netstar/nand.c index b76d2a3324..302d78efef 100644 --- a/board/netstar/nand.c +++ b/board/netstar/nand.c @@ -21,6 +21,7 @@ */ #include +#include #if defined(CONFIG_CMD_NAND) @@ -32,24 +33,29 @@ #define MASK_CLE 0x02 #define MASK_ALE 0x04 -static void netstar_nand_hwcontrol(struct mtd_info *mtd, int cmd) +static void netstar_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct nand_chip *this = mtd->priv; ulong IO_ADDR_W = (ulong) this->IO_ADDR_W; IO_ADDR_W &= ~(MASK_ALE|MASK_CLE); - switch (cmd) { - case NAND_CTL_SETCLE: IO_ADDR_W |= MASK_CLE; break; - case NAND_CTL_SETALE: IO_ADDR_W |= MASK_ALE; break; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + IO_ADDR_W |= MASK_CLE; + if ( ctrl & NAND_ALE ) + IO_ADDR_W |= MASK_ALE; } - this->IO_ADDR_W = (void *) IO_ADDR_W; + this->IO_ADDR_W = (void __iomem *) IO_ADDR_W; + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } int board_nand_init(struct nand_chip *nand) { nand->options = NAND_SAMSUNG_LP_OPTIONS; - nand->eccmode = NAND_ECC_SOFT; - nand->hwcontrol = netstar_nand_hwcontrol; + nand->ecc.mode = NAND_ECC_SOFT; + nand->cmd_ctrl = netstar_nand_hwcontrol; nand->chip_delay = 400; return 0; } diff --git a/board/prodrive/alpr/nand.c b/board/prodrive/alpr/nand.c index 097e183719..3224d3dd63 100644 --- a/board/prodrive/alpr/nand.c +++ b/board/prodrive/alpr/nand.c @@ -56,43 +56,24 @@ static struct alpr_ndfc_regs *alpr_ndfc = NULL; * * There are 2 NAND devices on the board, a Hynix HY27US08561A (1 GByte). */ -static void alpr_nand_hwcontrol(struct mtd_info *mtd, int cmd) -{ - switch (cmd) { - case NAND_CTL_SETCLE: - hwctl |= 0x1; - break; - case NAND_CTL_CLRCLE: - hwctl &= ~0x1; - break; - case NAND_CTL_SETALE: - hwctl |= 0x2; - break; - case NAND_CTL_CLRALE: - hwctl &= ~0x2; - break; - case NAND_CTL_SETNCE: - break; - case NAND_CTL_CLRNCE: - writeb(0x00, &(alpr_ndfc->term)); - break; - } -} +static void alpr_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *this = mtd->priv; -static void alpr_nand_write_byte(struct mtd_info *mtd, u_char byte) -{ - struct nand_chip *nand = mtd->priv; - - if (hwctl & 0x1) - /* - * IO_ADDR_W used as CMD[i] reg to support multiple NAND - * chips. - */ - writeb(byte, nand->IO_ADDR_W); - else if (hwctl & 0x2) { - writeb(byte, &(alpr_ndfc->addr_wait)); - } else - writeb(byte, &(alpr_ndfc->data)); + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + hwctl |= 0x1; + else + hwctl &= ~0x1; + if ( ctrl & NAND_ALE ) + hwctl |= 0x2; + else + hwctl &= ~0x2; + if ( (ctrl & NAND_NCE) != NAND_NCE) + writeb(0x00, &(alpr_ndfc->term)); + } + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } static u_char alpr_nand_read_byte(struct mtd_info *mtd) @@ -158,12 +139,10 @@ int board_nand_init(struct nand_chip *nand) { alpr_ndfc = (struct alpr_ndfc_regs *)CFG_NAND_BASE; - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; /* Reference hardware control function */ - nand->hwcontrol = alpr_nand_hwcontrol; - /* Set command delay time */ - nand->write_byte = alpr_nand_write_byte; + nand->cmd_ctrl = alpr_nand_hwcontrol; nand->read_byte = alpr_nand_read_byte; nand->write_buf = alpr_nand_write_buf; nand->read_buf = alpr_nand_read_buf; diff --git a/board/prodrive/pdnb3/nand.c b/board/prodrive/pdnb3/nand.c index b1e7041046..281ae70af6 100644 --- a/board/prodrive/pdnb3/nand.c +++ b/board/prodrive/pdnb3/nand.c @@ -52,40 +52,26 @@ static struct pdnb3_ndfc_regs *pdnb3_ndfc; * * There is one NAND devices on the board, a Hynix HY27US08561A (32 MByte). */ -static void pdnb3_nand_hwcontrol(struct mtd_info *mtd, int cmd) +static void pdnb3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch (cmd) { - case NAND_CTL_SETCLE: - hwctl |= 0x1; - break; - case NAND_CTL_CLRCLE: - hwctl &= ~0x1; - break; - - case NAND_CTL_SETALE: - hwctl |= 0x2; - break; - case NAND_CTL_CLRALE: - hwctl &= ~0x2; - break; - - case NAND_CTL_SETNCE: - break; - case NAND_CTL_CLRNCE: - writeb(0x00, &(pdnb3_ndfc->term)); - break; + struct nand_chip *this = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + hwctl |= 0x1; + else + hwctl &= ~0x1; + if ( ctrl & NAND_ALE ) + hwctl |= 0x2; + else + hwctl &= ~0x2; + if ( (ctrl & NAND_NCE) != NAND_NCE) + writeb(0x00, &(pdnb3_ndfc->term)); } + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } -static void pdnb3_nand_write_byte(struct mtd_info *mtd, u_char byte) -{ - if (hwctl & 0x1) - writeb(byte, &(pdnb3_ndfc->cmd)); - else if (hwctl & 0x2) - writeb(byte, &(pdnb3_ndfc->addr)); - else - writeb(byte, &(pdnb3_ndfc->data)); -} static u_char pdnb3_nand_read_byte(struct mtd_info *mtd) { @@ -152,16 +138,13 @@ int board_nand_init(struct nand_chip *nand) { pdnb3_ndfc = (struct pdnb3_ndfc_regs *)CFG_NAND_BASE; - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; /* Set address of NAND IO lines (Using Linear Data Access Region) */ nand->IO_ADDR_R = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4); nand->IO_ADDR_W = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4); /* Reference hardware control function */ - nand->hwcontrol = pdnb3_nand_hwcontrol; - /* Set command delay time */ - nand->hwcontrol = pdnb3_nand_hwcontrol; - nand->write_byte = pdnb3_nand_write_byte; + nand->cmd_ctrl = pdnb3_nand_hwcontrol; nand->read_byte = pdnb3_nand_read_byte; nand->write_buf = pdnb3_nand_write_buf; nand->read_buf = pdnb3_nand_read_buf; diff --git a/board/sc3/sc3nand.c b/board/sc3/sc3nand.c index 009567b50b..2f2e745897 100644 --- a/board/sc3/sc3nand.c +++ b/board/sc3/sc3nand.c @@ -39,30 +39,26 @@ static void *sc3_io_base; static void *sc3_control_base = (void *)0xEF600700; -static void sc3_nand_hwcontrol(struct mtd_info *mtd, int cmd) +static void sc3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch (cmd) { - case NAND_CTL_SETCLE: - set_bit (SC3_NAND_CLE, sc3_control_base); - break; - case NAND_CTL_CLRCLE: - clear_bit (SC3_NAND_CLE, sc3_control_base); - break; - - case NAND_CTL_SETALE: - set_bit (SC3_NAND_ALE, sc3_control_base); - break; - case NAND_CTL_CLRALE: - clear_bit (SC3_NAND_ALE, sc3_control_base); - break; - - case NAND_CTL_SETNCE: - set_bit (SC3_NAND_CE, sc3_control_base); - break; - case NAND_CTL_CLRNCE: - clear_bit (SC3_NAND_CE, sc3_control_base); - break; + struct nand_chip *this = mtd->priv; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + set_bit (SC3_NAND_CLE, sc3_control_base); + else + clear_bit (SC3_NAND_CLE, sc3_control_base); + if ( ctrl & NAND_ALE ) + set_bit (SC3_NAND_ALE, sc3_control_base); + else + clear_bit (SC3_NAND_ALE, sc3_control_base); + if ( ctrl & NAND_NCE ) + set_bit (SC3_NAND_CE, sc3_control_base); + else + clear_bit (SC3_NAND_CE, sc3_control_base); } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } static int sc3_nand_dev_ready(struct mtd_info *mtd) @@ -79,14 +75,14 @@ static void sc3_select_chip(struct mtd_info *mtd, int chip) int board_nand_init(struct nand_chip *nand) { - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; sc3_io_base = (void *) CFG_NAND_BASE; /* Set address of NAND IO lines (Using Linear Data Access Region) */ nand->IO_ADDR_R = (void __iomem *) sc3_io_base; nand->IO_ADDR_W = (void __iomem *) sc3_io_base; /* Reference hardware control function */ - nand->hwcontrol = sc3_nand_hwcontrol; + nand->cmd_ctrl = sc3_nand_hwcontrol; nand->dev_ready = sc3_nand_dev_ready; nand->select_chip = sc3_select_chip; return 0; diff --git a/board/tqc/tqm8272/tqm8272.c b/board/tqc/tqm8272/tqm8272.c index cde02961be..5148f3de5f 100644 --- a/board/tqc/tqm8272/tqm8272.c +++ b/board/tqc/tqm8272/tqm8272.c @@ -1068,24 +1068,22 @@ int update_flash_size (int flash_size) static u8 hwctl = 0; -static void upmnand_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void upmnand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch (cmd) { - case NAND_CTL_SETCLE: - hwctl |= 0x1; - break; - case NAND_CTL_CLRCLE: - hwctl &= ~0x1; - break; - - case NAND_CTL_SETALE: - hwctl |= 0x2; - break; - - case NAND_CTL_CLRALE: - hwctl &= ~0x2; - break; + struct nand_chip *this = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + hwctl |= 0x1; + else + hwctl &= ~0x1; + if ( ctrl & NAND_ALE ) + hwctl |= 0x2; + else + hwctl &= ~0x2; } + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } static void upmnand_write_byte(struct mtd_info *mtdinfo, u_char byte) @@ -1188,9 +1186,9 @@ int board_nand_init(struct nand_chip *nand) memctl->memc_br3 = CFG_NAND_BR; memctl->memc_mbmr = (MxMR_OP_NORM); - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; - nand->hwcontrol = upmnand_hwcontrol; + nand->cmd_ctrl = upmnand_hwcontrol; nand->read_byte = upmnand_read_byte; nand->write_byte = upmnand_write_byte; nand->dev_ready = tqm8272_dev_ready; diff --git a/board/zylonite/nand.c b/board/zylonite/nand.c index ca16578432..47d5d4b0d7 100644 --- a/board/zylonite/nand.c +++ b/board/zylonite/nand.c @@ -69,7 +69,7 @@ static struct nand_oobinfo delta_oob = { /* * not required for Monahans DFC */ -static void dfc_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void dfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { return; } @@ -110,25 +110,6 @@ static void dfc_write_buf(struct mtd_info *mtd, const u_char *buf, int len) } -/* - * These functions are quite problematic for the DFC. Luckily they are - * not used in the current nand code, except for nand_command, which - * we've defined our own anyway. The problem is, that we always need - * to write 4 bytes to the DFC Data Buffer, but in these functions we - * don't know if to buffer the bytes/half words until we've gathered 4 - * bytes or if to send them straight away. - * - * Solution: Don't use these with Mona's DFC and complain loudly. - */ -static void dfc_write_word(struct mtd_info *mtd, u16 word) -{ - printf("dfc_write_word: WARNING, this function does not work with the Monahans DFC!\n"); -} -static void dfc_write_byte(struct mtd_info *mtd, u_char byte) -{ - printf("dfc_write_byte: WARNING, this function does not work with the Monahans DFC!\n"); -} - /* The original: * static void dfc_read_buf(struct mtd_info *mtd, const u_char *buf, int len) * @@ -168,7 +149,7 @@ static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len) */ static u16 dfc_read_word(struct mtd_info *mtd) { - printf("dfc_write_byte: UNIMPLEMENTED.\n"); + printf("dfc_read_word: UNIMPLEMENTED.\n"); return 0; } @@ -289,9 +270,10 @@ static void dfc_new_cmd(void) /* this function is called after Programm and Erase Operations to * check for success or failure */ -static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this, int state) +static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this) { unsigned long ndsr=0, event=0; + int state = this->state; if(state == FL_WRITING) { event = NDSR_CS0_CMDD | NDSR_CS0_BBD; @@ -435,11 +417,11 @@ static void dfc_gpio_init(void) * argument are board-specific (per include/linux/mtd/nand_new.h): * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device - * - hwcontrol: hardwarespecific function for accesing control-lines + * - cmd_ctrl: hardwarespecific function for accesing control-lines * - dev_ready: hardwarespecific function for accesing device ready/busy line * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must * only be provided if a hardware ECC is available - * - eccmode: mode of ecc, see defines + * - ecc.mode: mode of ecc, see defines * - chip_delay: chip dependent delay for transfering data from array to * read regs (tR) * - options: various chip options. They can partly be set to inform @@ -560,21 +542,18 @@ int board_nand_init(struct nand_chip *nand) /* wait 10 us due to cmd buffer clear reset */ /* wait(10); */ - - nand->hwcontrol = dfc_hwcontrol; + nand->cmd_ctrl = dfc_hwcontrol; /* nand->dev_ready = dfc_device_ready; */ - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; nand->options = NAND_BUSWIDTH_16; nand->waitfunc = dfc_wait; nand->read_byte = dfc_read_byte; - nand->write_byte = dfc_write_byte; nand->read_word = dfc_read_word; - nand->write_word = dfc_write_word; nand->read_buf = dfc_read_buf; nand->write_buf = dfc_write_buf; nand->cmdfunc = dfc_cmdfunc; - nand->autooob = &delta_oob; +// nand->autooob = &delta_oob; nand->badblock_pattern = &delta_bbt_descr; return 0; } diff --git a/common/cmd_doc.c b/common/cmd_doc.c index d7b2f535f3..9d5b3001cc 100644 --- a/common/cmd_doc.c +++ b/common/cmd_doc.c @@ -14,6 +14,7 @@ #include #include +#if 0 #ifdef CFG_DOC_SUPPORT_2000 #define DoC_is_2000(doc) (doc->ChipID == DOC_ChipID_Doc2k) #else @@ -1629,3 +1630,6 @@ void doc_probe(unsigned long physadr) puts ("No DiskOnChip found\n"); } } +#else +void doc_probe(unsigned long physadr) {} +#endif diff --git a/common/cmd_nand.c b/common/cmd_nand.c index 9e38bf768f..3e76d8207d 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -18,6 +18,7 @@ * */ #include +#include #if defined(CONFIG_CMD_NAND) @@ -34,7 +35,7 @@ int mtdparts_init(void); int id_parse(const char *id, const char **ret_id, u8 *dev_type, u8 *dev_num); int find_dev_and_part(const char *id, struct mtd_device **dev, - u8 *part_num, struct part_info **part); + u8 *part_num, struct part_info **part); #endif static int nand_dump_oob(nand_info_t *nand, ulong off) @@ -47,32 +48,38 @@ static int nand_dump(nand_info_t *nand, ulong off) int i; u_char *buf, *p; - buf = malloc(nand->oobblock + nand->oobsize); + buf = malloc(nand->writesize + nand->oobsize); if (!buf) { puts("No memory for page buffer\n"); return 1; } - off &= ~(nand->oobblock - 1); - i = nand_read_raw(nand, buf, off, nand->oobblock, nand->oobsize); + off &= ~(nand->writesize - 1); +#if 0 + i = nand_read_raw(nand, buf, off, nand->writesize, nand->oobsize); +#else + size_t dummy; + loff_t addr = (loff_t) off; + i = nand->read(nand, addr, nand->writesize, &dummy, buf); +#endif if (i < 0) { printf("Error (%d) reading page %08lx\n", i, off); free(buf); return 1; } printf("Page %08lx dump:\n", off); - i = nand->oobblock >> 4; p = buf; + i = nand->writesize >> 4; p = buf; while (i--) { - printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x" - " %02x %02x %02x %02x %02x %02x %02x %02x\n", - p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], - p[8], p[9], p[10], p[11], p[12], p[13], p[14], p[15]); + printf("\t%02x %02x %02x %02x %02x %02x %02x %02x" + " %02x %02x %02x %02x %02x %02x %02x %02x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], + p[8], p[9], p[10], p[11], p[12], p[13], p[14], p[15]); p += 16; } puts("OOB:\n"); i = nand->oobsize >> 3; while (i--) { - printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x\n", - p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7]); + printf("\t%02x %02x %02x %02x %02x %02x %02x %02x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7]); p += 8; } free(buf); @@ -155,7 +162,7 @@ out: int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) { - int i, dev, ret; + int i, dev, ret = 0; ulong addr, off; size_t size; char *cmd, *s; @@ -182,8 +189,8 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) for (i = 0; i < CFG_MAX_NAND_DEVICE; i++) { if (nand_info[i].name) printf("Device %d: %s, sector size %u KiB\n", - i, nand_info[i].name, - nand_info[i].erasesize >> 10); + i, nand_info[i].name, + nand_info[i].erasesize >> 10); } return 0; } @@ -192,11 +199,11 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) if (argc < 3) { if ((nand_curr_device < 0) || - (nand_curr_device >= CFG_MAX_NAND_DEVICE)) + (nand_curr_device >= CFG_MAX_NAND_DEVICE)) puts("\nno devices available\n"); else printf("\nDevice %d: %s\n", nand_curr_device, - nand_info[nand_curr_device].name); + nand_info[nand_curr_device].name); return 0; } dev = (int)simple_strtoul(argv[2], NULL, 10); @@ -219,11 +226,11 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) } if (strcmp(cmd, "bad") != 0 && strcmp(cmd, "erase") != 0 && - strncmp(cmd, "dump", 4) != 0 && - strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0 && - strcmp(cmd, "scrub") != 0 && strcmp(cmd, "markbad") != 0 && - strcmp(cmd, "biterr") != 0 && - strcmp(cmd, "lock") != 0 && strcmp(cmd, "unlock") != 0 ) + strncmp(cmd, "dump", 4) != 0 && + strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0 && + strcmp(cmd, "scrub") != 0 && strcmp(cmd, "markbad") != 0 && + strcmp(cmd, "biterr") != 0 && + strcmp(cmd, "lock") != 0 && strcmp(cmd, "unlock") != 0 ) goto usage; /* the following commands operate on the current device */ @@ -250,7 +257,7 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) if (strcmp(cmd, "erase") == 0 || strcmp(cmd, "scrub") == 0) { nand_erase_options_t opts; /* "clean" at index 2 means request to write cleanmarker */ - int clean = argc > 2 && !strcmp("clean", argv[2]); + int clean = !strcmp("clean", argv[2]); int o = clean ? 3 : 2; int scrub = !strcmp(cmd, "scrub"); @@ -260,6 +267,7 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) return 1; memset(&opts, 0, sizeof(opts)); + opts.offset = off; opts.length = size; opts.jffs2 = clean; @@ -320,40 +328,41 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) printf("\nNAND %s: ", read ? "read" : "write"); if (arg_off_size(argc - 3, argv + 3, nand, &off, &size) != 0) return 1; - + s = strchr(cmd, '.'); if (s != NULL && - (!strcmp(s, ".jffs2") || !strcmp(s, ".e") || !strcmp(s, ".i"))) { + (!strcmp(s, ".jffs2") || !strcmp(s, ".e") || !strcmp(s, ".i"))) { if (read) { /* read */ nand_read_options_t opts; memset(&opts, 0, sizeof(opts)); - opts.buffer = (u_char*) addr; - opts.length = size; - opts.offset = off; - opts.quiet = quiet; - ret = nand_read_opts(nand, &opts); + opts.buffer = (u_char*) addr; + opts.length = size; + opts.offset = off; + opts.quiet = quiet; +// ret = nand_read_opts(nand, &opts); } else { /* write */ - nand_write_options_t opts; + mtd_oob_ops_t opts; memset(&opts, 0, sizeof(opts)); - opts.buffer = (u_char*) addr; - opts.length = size; - opts.offset = off; - /* opts.forcejffs2 = 1; */ - opts.pad = 1; - opts.blockalign = 1; - opts.quiet = quiet; - ret = nand_write_opts(nand, &opts); + opts.datbuf = (u_char*) addr; + opts.len = size; + opts.ooblen = 64; + opts.mode = MTD_OOB_AUTO; + ret = nand_write_opts(nand, off, &opts); } } else if (s != NULL && !strcmp(s, ".oob")) { - /* read out-of-band data */ + /* out-of-band data */ + mtd_oob_ops_t ops = { + .oobbuf = (u8 *)addr, + .ooblen = size, + .mode = MTD_OOB_RAW + }; + if (read) - ret = nand->read_oob(nand, off, size, &size, - (u_char *) addr); + ret = nand->read_oob(nand, off, &ops); else - ret = nand->write_oob(nand, off, size, &size, - (u_char *) addr); + ret = nand->write_oob(nand, off, &ops); } else { if (read) ret = nand_read(nand, off, &size, (u_char *)addr); @@ -397,44 +406,44 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) } if (status) { - ulong block_start = 0; +// ulong block_start = 0; ulong off; - int last_status = -1; +// int last_status = -1; struct nand_chip *nand_chip = nand->priv; /* check the WP bit */ nand_chip->cmdfunc (nand, NAND_CMD_STATUS, -1, -1); printf("device is %swrite protected\n", (nand_chip->read_byte(nand) & 0x80 ? - "NOT " : "" ) ); - - for (off = 0; off < nand->size; off += nand->oobblock) { - int s = nand_get_lock_status(nand, off); - - /* print message only if status has changed - * or at end of chip - */ - if (off == nand->size - nand->oobblock - || (s != last_status && off != 0)) { - - printf("%08lx - %08lx: %8lu pages %s%s%s\n", - block_start, - off-1, - (off-block_start)/nand->oobblock, - ((last_status & NAND_LOCK_STATUS_TIGHT) ? "TIGHT " : ""), - ((last_status & NAND_LOCK_STATUS_LOCK) ? "LOCK " : ""), - ((last_status & NAND_LOCK_STATUS_UNLOCK) ? "UNLOCK " : "")); - } - - last_status = s; - } - } else { - if (!nand_lock(nand, tight)) { - puts("NAND flash successfully locked\n"); - } else { - puts("Error locking NAND flash\n"); - return 1; + "NOT " : "" ) ); + + for (off = 0; off < nand->size; off += nand->writesize) { +// int s = nand_get_lock_status(nand, off); +// +// /* print message only if status has changed +// * or at end of chip +// */ +// if (off == nand->size - nand->writesize +// || (s != last_status && off != 0)) { +// +// printf("%08lx - %08lx: %8d pages %s%s%s\n", +// block_start, +// off-1, +// (off-block_start)/nand->writesize, +// ((last_status & NAND_LOCK_STATUS_TIGHT) ? "TIGHT " : ""), +// ((last_status & NAND_LOCK_STATUS_LOCK) ? "LOCK " : ""), +// ((last_status & NAND_LOCK_STATUS_UNLOCK) ? "UNLOCK " : "")); +// } +// +// last_status = s; } + } else { +// if (!nand_lock(nand, tight)) { +// puts("NAND flash successfully locked\n"); +// } else { +// puts("Error locking NAND flash\n"); +// return 1; +// } } return 0; } @@ -443,13 +452,13 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) if (arg_off_size(argc - 2, argv + 2, nand, &off, &size) < 0) return 1; - if (!nand_unlock(nand, off, size)) { - puts("NAND flash successfully unlocked\n"); - } else { - puts("Error unlocking NAND flash, " - "write and erase will probably fail\n"); - return 1; - } +// if (!nand_unlock(nand, off, size)) { +// puts("NAND flash successfully unlocked\n"); +// } else { +// puts("Error unlocking NAND flash, " +// "write and erase will probably fail\n"); +// return 1; +// } return 0; } @@ -459,24 +468,26 @@ usage: } U_BOOT_CMD(nand, 5, 1, do_nand, - "nand - NAND sub-system\n", - "info - show available NAND devices\n" - "nand device [dev] - show or set current device\n" - "nand read[.jffs2] - addr off|partition size\n" - "nand write[.jffs2] - addr off|partition size - read/write `size' bytes starting\n" - " at offset `off' to/from memory address `addr'\n" - "nand erase [clean] [off size] - erase `size' bytes from\n" - " offset `off' (entire device if not specified)\n" - "nand bad - show bad blocks\n" - "nand dump[.oob] off - dump page\n" - "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n" - "nand markbad off - mark bad block at offset (UNSAFE)\n" - "nand biterr off - make a bit error at offset (UNSAFE)\n" - "nand lock [tight] [status] - bring nand to lock state or display locked pages\n" - "nand unlock [offset] [size] - unlock section\n"); + "nand - NAND sub-system\n", + "info - show available NAND devices\n" + "nand device [dev] - show or set current device\n" + "nand read[.jffs2] - addr off|partition size\n" + "nand write[.jffs2] - addr off|partition size\n" + " read/write 'size' bytes starting at offset 'off'\n" + " to/from memory address 'addr'\n" + "nand erase [clean] [off size] - erase 'size' bytes from\n" + " offset 'off' (entire device if not specified)\n" + "nand bad - show bad blocks\n" + "nand dump[.oob] off - dump page\n" + "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n" + "nand markbad off - mark bad block at offset (UNSAFE)\n" + "nand biterr off - make a bit error at offset (UNSAFE)\n" + "nand lock [tight] [status]\n" + " bring nand to lock state or display locked pages\n" + "nand unlock [offset] [size] - unlock section\n"); static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand, - ulong offset, ulong addr, char *cmd) + ulong offset, ulong addr, char *cmd) { int r; char *ep, *s; @@ -494,19 +505,8 @@ static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand, printf("\nLoading from %s, offset 0x%lx\n", nand->name, offset); - cnt = nand->oobblock; - if (jffs2) { - nand_read_options_t opts; - memset(&opts, 0, sizeof(opts)); - opts.buffer = (u_char*) addr; - opts.length = cnt; - opts.offset = offset; - opts.quiet = 1; - r = nand_read_opts(nand, &opts); - } else { - r = nand_read(nand, offset, &cnt, (u_char *) addr); - } - + cnt = nand->writesize; + r = nand_read(nand, offset, &cnt, (u_char *) addr); if (r) { puts("** Read error\n"); show_boot_progress (-56); @@ -537,18 +537,7 @@ static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand, return 1; } - if (jffs2) { - nand_read_options_t opts; - memset(&opts, 0, sizeof(opts)); - opts.buffer = (u_char*) addr; - opts.length = cnt; - opts.offset = offset; - opts.quiet = 1; - r = nand_read_opts(nand, &opts); - } else { - r = nand_read(nand, offset, &cnt, (u_char *) addr); - } - + r = nand_read(nand, offset, &cnt, (u_char *) addr); if (r) { puts("** Read error\n"); show_boot_progress (-58); @@ -614,7 +603,7 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) else addr = CFG_LOAD_ADDR; return nand_load_image(cmdtp, &nand_info[dev->id->num], - part->offset, addr, argv[0]); + part->offset, addr, argv[0]); } } #endif @@ -704,8 +693,8 @@ void archflashwp(void *archdata, int wp); #define ROUND_DOWN(value,boundary) ((value) & (~((boundary)-1))) -#undef NAND_DEBUG -#undef PSYCHO_DEBUG +#undef NAND_DEBUG +#undef PSYCHO_DEBUG /* ****************** WARNING ********************* * When ALLOW_ERASE_BAD_DEBUG is non-zero the erase command will @@ -720,16 +709,16 @@ void archflashwp(void *archdata, int wp); * and attempting to program or erase bad blocks can affect * the data in _other_ (good) blocks. */ -#define ALLOW_ERASE_BAD_DEBUG 0 +#define ALLOW_ERASE_BAD_DEBUG 0 #define CONFIG_MTD_NAND_ECC /* enable ECC */ #define CONFIG_MTD_NAND_ECC_JFFS2 /* bits for nand_legacy_rw() `cmd'; or together as needed */ -#define NANDRW_READ 0x01 -#define NANDRW_WRITE 0x00 -#define NANDRW_JFFS2 0x02 -#define NANDRW_JFFS2_SKIP 0x04 +#define NANDRW_READ 0x01 +#define NANDRW_WRITE 0x00 +#define NANDRW_JFFS2 0x02 +#define NANDRW_JFFS2_SKIP 0x04 /* * Imports from nand_legacy.c @@ -737,15 +726,15 @@ void archflashwp(void *archdata, int wp); extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; extern int curr_device; extern int nand_legacy_erase(struct nand_chip *nand, size_t ofs, - size_t len, int clean); + size_t len, int clean); extern int nand_legacy_rw(struct nand_chip *nand, int cmd, size_t start, - size_t len, size_t *retlen, u_char *buf); + size_t len, size_t *retlen, u_char *buf); extern void nand_print(struct nand_chip *nand); extern void nand_print_bad(struct nand_chip *nand); extern int nand_read_oob(struct nand_chip *nand, size_t ofs, - size_t len, size_t *retlen, u_char *buf); + size_t len, size_t *retlen, u_char *buf); extern int nand_write_oob(struct nand_chip *nand, size_t ofs, - size_t len, size_t *retlen, const u_char *buf); + size_t len, size_t *retlen, const u_char *buf); int do_nand (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) @@ -878,7 +867,7 @@ int do_nand (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) else if (cmdtail && !strcmp (cmdtail, ".i")) { cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */ if (cmd & NANDRW_READ) - cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */ + cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */ } #endif /* CFG_NAND_SKIP_BAD_DOT_I */ else if (cmdtail) { @@ -928,7 +917,7 @@ int do_nand (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) } U_BOOT_CMD( - nand, 5, 1, do_nand, + nand, 5, 1, do_nand, "nand - legacy NAND sub-system\n", "info - show available NAND devices\n" "nand device [dev] - show or set current device\n" @@ -992,7 +981,7 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) dev = simple_strtoul(boot_device, &ep, 16); if ((dev >= CFG_MAX_NAND_DEVICE) || - (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN)) { + (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN)) { printf ("\n** Device %d not available\n", dev); show_boot_progress (-55); return 1; @@ -1000,11 +989,11 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) show_boot_progress (55); printf ("\nLoading from device %d: %s at 0x%lx (offset 0x%lx)\n", - dev, nand_dev_desc[dev].name, nand_dev_desc[dev].IO_ADDR, - offset); + dev, nand_dev_desc[dev].name, nand_dev_desc[dev].IO_ADDR, + offset); if (nand_legacy_rw (nand_dev_desc + dev, NANDRW_READ, offset, - SECTORSIZE, NULL, (u_char *)addr)) { + SECTORSIZE, NULL, (u_char *)addr)) { printf ("** Read error on %d\n", dev); show_boot_progress (-56); return 1; @@ -1035,8 +1024,8 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) show_boot_progress (57); if (nand_legacy_rw (nand_dev_desc + dev, NANDRW_READ, - offset + SECTORSIZE, cnt, NULL, - (u_char *)(addr+SECTORSIZE))) { + offset + SECTORSIZE, cnt, NULL, + (u_char *)(addr+SECTORSIZE))) { printf ("** Read error on %d\n", dev); show_boot_progress (-58); return 1; @@ -1077,7 +1066,7 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) } U_BOOT_CMD( - nboot, 4, 1, do_nandboot, + nboot, 4, 1, do_nandboot, "nboot - boot from NAND device\n", "loadAddr dev\n" ); diff --git a/cpu/arm926ejs/davinci/nand.c b/cpu/arm926ejs/davinci/nand.c index 36468e6c3a..43041b635c 100644 --- a/cpu/arm926ejs/davinci/nand.c +++ b/cpu/arm926ejs/davinci/nand.c @@ -42,6 +42,7 @@ */ #include +#include #ifdef CFG_USE_NAND #if !defined(CFG_NAND_LEGACY) @@ -52,23 +53,23 @@ extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; -static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd) +static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct nand_chip *this = mtd->priv; u_int32_t IO_ADDR_W = (u_int32_t)this->IO_ADDR_W; IO_ADDR_W &= ~(MASK_ALE|MASK_CLE); - switch (cmd) { - case NAND_CTL_SETCLE: + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) IO_ADDR_W |= MASK_CLE; - break; - case NAND_CTL_SETALE: + if ( ctrl & NAND_ALE ) IO_ADDR_W |= MASK_ALE; - break; + this->IO_ADDR_W = (void __iomem *) IO_ADDR_W; } - this->IO_ADDR_W = (void *)IO_ADDR_W; + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } /* Set WP on deselect, write enable on select */ @@ -145,7 +146,7 @@ static int nand_davinci_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u int region, n; struct nand_chip *this = mtd->priv; - n = (this->eccmode == NAND_ECC_HW12_2048) ? 4 : 1; + n = (this->ecc.size/512); region = 1; while (n--) { @@ -281,7 +282,7 @@ static int nand_davinci_correct_data(struct mtd_info *mtd, u_char *dat, u_char * int block_count = 0, i, rc; this = mtd->priv; - block_count = (this->eccmode == NAND_ECC_HW12_2048) ? 4 : 1; + block_count = (this->ecc.size/512); for (i = 0; i < block_count; i++) { if (memcmp(read_ecc, calc_ecc, 3) != 0) { rc = nand_davinci_compare_ecc(read_ecc, calc_ecc, dat); @@ -306,7 +307,7 @@ static int nand_davinci_dev_ready(struct mtd_info *mtd) return(emif_addr->NANDFSR & 0x1); } -static int nand_davinci_waitfunc(struct mtd_info *mtd, struct nand_chip *this, int state) +static int nand_davinci_waitfunc(struct mtd_info *mtd, struct nand_chip *this) { while(!nand_davinci_dev_ready(mtd)) {;} *NAND_CE0CLE = NAND_STATUS; @@ -362,22 +363,26 @@ int board_nand_init(struct nand_chip *nand) #endif #ifdef CFG_NAND_HW_ECC #ifdef CFG_NAND_LARGEPAGE - nand->eccmode = NAND_ECC_HW12_2048; + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.size = 2048; + nand->ecc.bytes = 12; #elif defined(CFG_NAND_SMALLPAGE) - nand->eccmode = NAND_ECC_HW3_512; + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.size = 512; + nand->ecc.bytes = 3; #else #error "Either CFG_NAND_LARGEPAGE or CFG_NAND_SMALLPAGE must be defined!" #endif - nand->autooob = &davinci_nand_oobinfo; - nand->calculate_ecc = nand_davinci_calculate_ecc; - nand->correct_data = nand_davinci_correct_data; - nand->enable_hwecc = nand_davinci_enable_hwecc; +// nand->autooob = &davinci_nand_oobinfo; + nand->ecc.calculate = nand_davinci_calculate_ecc; + nand->ecc.correct = nand_davinci_correct_data; + nand->ecc.hwctl = nand_davinci_enable_hwecc; #else - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; #endif /* Set address of hardware control function */ - nand->hwcontrol = nand_davinci_hwcontrol; + nand->cmd_ctrl = nand_davinci_hwcontrol; nand->dev_ready = nand_davinci_dev_ready; nand->waitfunc = nand_davinci_waitfunc; diff --git a/cpu/ppc4xx/ndfc.c b/cpu/ppc4xx/ndfc.c index 5b2ae88d93..7818eb9c54 100644 --- a/cpu/ppc4xx/ndfc.c +++ b/cpu/ppc4xx/ndfc.c @@ -46,38 +46,22 @@ static u8 hwctl = 0; -static void ndfc_hwcontrol(struct mtd_info *mtdinfo, int cmd) +static void ndfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch (cmd) { - case NAND_CTL_SETCLE: - hwctl |= 0x1; - break; - - case NAND_CTL_CLRCLE: - hwctl &= ~0x1; - break; - - case NAND_CTL_SETALE: - hwctl |= 0x2; - break; - - case NAND_CTL_CLRALE: - hwctl &= ~0x2; - break; + struct nand_chip *this = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + hwctl |= 0x1; + else + hwctl &= ~0x1; + if ( ctrl & NAND_ALE ) + hwctl |= 0x2; + else + hwctl &= ~0x2; } -} - -static void ndfc_write_byte(struct mtd_info *mtdinfo, u_char byte) -{ - struct nand_chip *this = mtdinfo->priv; - ulong base = (ulong) this->IO_ADDR_W & 0xfffffffc; - - if (hwctl & 0x1) - out_8((u8 *)(base + NDFC_CMD), byte); - else if (hwctl & 0x2) - out_8((u8 *)(base + NDFC_ALE), byte); - else - out_8((u8 *)(base + NDFC_DATA), byte); + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } static u_char ndfc_read_byte(struct mtd_info *mtdinfo) @@ -194,16 +178,17 @@ int board_nand_init(struct nand_chip *nand) int cs = (ulong)nand->IO_ADDR_W & 0x00000003; ulong base = (ulong)nand->IO_ADDR_W & 0xfffffffc; - nand->hwcontrol = ndfc_hwcontrol; + nand->cmd_ctrl = ndfc_hwcontrol; nand->read_byte = ndfc_read_byte; nand->read_buf = ndfc_read_buf; - nand->write_byte = ndfc_write_byte; nand->dev_ready = ndfc_dev_ready; - nand->eccmode = NAND_ECC_HW3_256; - nand->enable_hwecc = ndfc_enable_hwecc; - nand->calculate_ecc = ndfc_calculate_ecc; - nand->correct_data = nand_correct_data; + nand->ecc.correct = nand_correct_data; + nand->ecc.hwctl = ndfc_enable_hwecc; + nand->ecc.calculate = ndfc_calculate_ecc; + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.size = 256; + nand->ecc.bytes = 3; #ifndef CONFIG_NAND_SPL nand->write_buf = ndfc_write_buf; diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c index fdd85c159d..a03f982be5 100644 --- a/drivers/mtd/nand/diskonchip.c +++ b/drivers/mtd/nand/diskonchip.c @@ -16,7 +16,7 @@ * * Interface to generic NAND code for M-Systems DiskOnChip devices * - * $Id: diskonchip.c,v 1.45 2005/01/05 18:05:14 dwmw2 Exp $ + * $Id: diskonchip.c,v 1.55 2005/11/07 11:14:30 gleixner Exp $ */ #include @@ -39,13 +39,13 @@ #include /* Where to look for the devices? */ -#ifndef CONFIG_MTD_DISKONCHIP_PROBE_ADDRESS -#define CONFIG_MTD_DISKONCHIP_PROBE_ADDRESS 0 +#ifndef CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS +#define CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS 0 #endif static unsigned long __initdata doc_locations[] = { #if defined (__alpha__) || defined(__i386__) || defined(__x86_64__) -#ifdef CONFIG_MTD_DISKONCHIP_PROBE_HIGH +#ifdef CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH 0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000, 0xfffd0000, 0xfffd2000, 0xfffd4000, 0xfffd6000, 0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000, @@ -65,7 +65,7 @@ static unsigned long __initdata doc_locations[] = { 0xff000000, #elif defined(CONFIG_MOMENCO_OCELOT_G) || defined (CONFIG_MOMENCO_OCELOT_C) 0xff000000, -##else +#else #warning Unknown architecture for DiskOnChip. No default probe locations defined #endif 0xffffffff }; @@ -77,7 +77,7 @@ struct doc_priv { unsigned long physadr; u_char ChipID; u_char CDSNControl; - int chips_per_floor; /* The number of chips detected on each floor */ + int chips_per_floor; /* The number of chips detected on each floor */ int curfloor; int curchip; int mh0_page; @@ -85,14 +85,10 @@ struct doc_priv { struct mtd_info *nextdoc; }; -/* Max number of eraseblocks to scan (from start of device) for the (I)NFTL - MediaHeader. The spec says to just keep going, I think, but that's just - silly. */ -#define MAX_MEDIAHEADER_SCAN 8 - /* This is the syndrome computed by the HW ecc generator upon reading an empty page, one with all 0xff for data and stored ecc code. */ static u_char empty_read_syndrome[6] = { 0x26, 0xff, 0x6d, 0x47, 0x73, 0x7a }; + /* This is the ecc value computed by the HW ecc generator upon writing an empty page, one with all 0xff for data. */ static u_char empty_write_ecc[6] = { 0x4b, 0x00, 0xe2, 0x0e, 0x93, 0xf7 }; @@ -103,35 +99,36 @@ static u_char empty_write_ecc[6] = { 0x4b, 0x00, 0xe2, 0x0e, 0x93, 0xf7 }; #define DoC_is_Millennium(doc) ((doc)->ChipID == DOC_ChipID_DocMil) #define DoC_is_2000(doc) ((doc)->ChipID == DOC_ChipID_Doc2k) -static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd); +static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int bitmask); static void doc200x_select_chip(struct mtd_info *mtd, int chip); -static int debug=0; +static int debug = 0; module_param(debug, int, 0); -static int try_dword=1; +static int try_dword = 1; module_param(try_dword, int, 0); -static int no_ecc_failures=0; +static int no_ecc_failures = 0; module_param(no_ecc_failures, int, 0); -#ifdef CONFIG_MTD_PARTITIONS -static int no_autopart=0; +static int no_autopart = 0; module_param(no_autopart, int, 0); -#endif -#ifdef MTD_NAND_DISKONCHIP_BBTWRITE -static int inftl_bbt_write=1; +static int show_firmware_partition = 0; +module_param(show_firmware_partition, int, 0); + +#ifdef CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE +static int inftl_bbt_write = 1; #else -static int inftl_bbt_write=0; +static int inftl_bbt_write = 0; #endif module_param(inftl_bbt_write, int, 0); -static unsigned long doc_config_location = CONFIG_MTD_DISKONCHIP_PROBE_ADDRESS; +static unsigned long doc_config_location = CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS; module_param(doc_config_location, ulong, 0); MODULE_PARM_DESC(doc_config_location, "Physical memory address at which to probe for DiskOnChip"); - /* Sector size for HW ECC */ #define SECTOR_SIZE 512 /* The sector bytes are packed into NB_DATA 10 bit words */ @@ -155,7 +152,7 @@ static struct rs_control *rs_decoder; * some comments, improved a minor bit and converted it to make use * of the generic Reed-Solomon libary. tglx */ -static int doc_ecc_decode (struct rs_control *rs, uint8_t *data, uint8_t *ecc) +static int doc_ecc_decode(struct rs_control *rs, uint8_t *data, uint8_t *ecc) { int i, j, nerr, errpos[8]; uint8_t parity; @@ -176,11 +173,11 @@ static int doc_ecc_decode (struct rs_control *rs, uint8_t *data, uint8_t *ecc) * s[i] = ds[3]x^3 + ds[2]x^2 + ds[1]x^1 + ds[0] * where x = alpha^(FCR + i) */ - for(j = 1; j < NROOTS; j++) { - if(ds[j] == 0) + for (j = 1; j < NROOTS; j++) { + if (ds[j] == 0) continue; tmp = rs->index_of[ds[j]]; - for(i = 0; i < NROOTS; i++) + for (i = 0; i < NROOTS; i++) s[i] ^= rs->alpha_to[rs_modnn(rs, tmp + (FCR + i) * j)]; } @@ -201,7 +198,7 @@ static int doc_ecc_decode (struct rs_control *rs, uint8_t *data, uint8_t *ecc) * but they are given by the design of the de/encoder circuit * in the DoC ASIC's. */ - for(i = 0;i < nerr; i++) { + for (i = 0; i < nerr; i++) { int index, bitpos, pos = 1015 - errpos[i]; uint8_t val; if (pos >= NB_DATA && pos < 1019) @@ -213,8 +210,7 @@ static int doc_ecc_decode (struct rs_control *rs, uint8_t *data, uint8_t *ecc) can be modified since pos is even */ index = (pos >> 3) ^ 1; bitpos = pos & 7; - if ((index >= 0 && index < SECTOR_SIZE) || - index == (SECTOR_SIZE + 1)) { + if ((index >= 0 && index < SECTOR_SIZE) || index == (SECTOR_SIZE + 1)) { val = (uint8_t) (errval[i] >> (2 + bitpos)); parity ^= val; if (index < SECTOR_SIZE) @@ -224,9 +220,8 @@ static int doc_ecc_decode (struct rs_control *rs, uint8_t *data, uint8_t *ecc) bitpos = (bitpos + 10) & 7; if (bitpos == 0) bitpos = 8; - if ((index >= 0 && index < SECTOR_SIZE) || - index == (SECTOR_SIZE + 1)) { - val = (uint8_t)(errval[i] << (8 - bitpos)); + if ((index >= 0 && index < SECTOR_SIZE) || index == (SECTOR_SIZE + 1)) { + val = (uint8_t) (errval[i] << (8 - bitpos)); parity ^= val; if (index < SECTOR_SIZE) data[index] ^= val; @@ -261,7 +256,8 @@ static int _DoC_WaitReady(struct doc_priv *doc) void __iomem *docptr = doc->virtadr; unsigned long timeo = jiffies + (HZ * 10); - if(debug) printk("_DoC_WaitReady...\n"); + if (debug) + printk("_DoC_WaitReady...\n"); /* Out-of-line routine to wait for chip response */ if (DoC_is_MillenniumPlus(doc)) { while ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) { @@ -306,7 +302,8 @@ static inline int DoC_WaitReady(struct doc_priv *doc) DoC_Delay(doc, 2); } - if(debug) printk("DoC_WaitReady OK\n"); + if (debug) + printk("DoC_WaitReady OK\n"); return ret; } @@ -316,7 +313,8 @@ static void doc2000_write_byte(struct mtd_info *mtd, u_char datum) struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; - if(debug)printk("write_byte %02x\n", datum); + if (debug) + printk("write_byte %02x\n", datum); WriteDOC(datum, docptr, CDSNSlowIO); WriteDOC(datum, docptr, 2k_CDSN_IO); } @@ -331,37 +329,39 @@ static u_char doc2000_read_byte(struct mtd_info *mtd) ReadDOC(docptr, CDSNSlowIO); DoC_Delay(doc, 2); ret = ReadDOC(docptr, 2k_CDSN_IO); - if (debug) printk("read_byte returns %02x\n", ret); + if (debug) + printk("read_byte returns %02x\n", ret); return ret; } -static void doc2000_writebuf(struct mtd_info *mtd, - const u_char *buf, int len) +static void doc2000_writebuf(struct mtd_info *mtd, const u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - if (debug)printk("writebuf of %d bytes: ", len); - for (i=0; i < len; i++) { + if (debug) + printk("writebuf of %d bytes: ", len); + for (i = 0; i < len; i++) { WriteDOC_(buf[i], docptr, DoC_2k_CDSN_IO + i); if (debug && i < 16) printk("%02x ", buf[i]); } - if (debug) printk("\n"); + if (debug) + printk("\n"); } -static void doc2000_readbuf(struct mtd_info *mtd, - u_char *buf, int len) +static void doc2000_readbuf(struct mtd_info *mtd, u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - if (debug)printk("readbuf of %d bytes: ", len); + if (debug) + printk("readbuf of %d bytes: ", len); - for (i=0; i < len; i++) { + for (i = 0; i < len; i++) { buf[i] = ReadDOC(docptr, 2k_CDSN_IO + i); } } @@ -374,28 +374,28 @@ static void doc2000_readbuf_dword(struct mtd_info *mtd, void __iomem *docptr = doc->virtadr; int i; - if (debug) printk("readbuf_dword of %d bytes: ", len); + if (debug) + printk("readbuf_dword of %d bytes: ", len); - if (unlikely((((unsigned long)buf)|len) & 3)) { - for (i=0; i < len; i++) { - *(uint8_t *)(&buf[i]) = ReadDOC(docptr, 2k_CDSN_IO + i); + if (unlikely((((unsigned long)buf) | len) & 3)) { + for (i = 0; i < len; i++) { + *(uint8_t *) (&buf[i]) = ReadDOC(docptr, 2k_CDSN_IO + i); } } else { - for (i=0; i < len; i+=4) { - *(uint32_t*)(&buf[i]) = readl(docptr + DoC_2k_CDSN_IO + i); + for (i = 0; i < len; i += 4) { + *(uint32_t*) (&buf[i]) = readl(docptr + DoC_2k_CDSN_IO + i); } } } -static int doc2000_verifybuf(struct mtd_info *mtd, - const u_char *buf, int len) +static int doc2000_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - for (i=0; i < len; i++) + for (i = 0; i < len; i++) if (buf[i] != ReadDOC(docptr, 2k_CDSN_IO)) return -EFAULT; return 0; @@ -408,12 +408,15 @@ static uint16_t __init doc200x_ident_chip(struct mtd_info *mtd, int nr) uint16_t ret; doc200x_select_chip(mtd, nr); - doc200x_hwcontrol(mtd, NAND_CTL_SETCLE); - this->write_byte(mtd, NAND_CMD_READID); - doc200x_hwcontrol(mtd, NAND_CTL_CLRCLE); - doc200x_hwcontrol(mtd, NAND_CTL_SETALE); - this->write_byte(mtd, 0); - doc200x_hwcontrol(mtd, NAND_CTL_CLRALE); + doc200x_hwcontrol(mtd, NAND_CMD_READID, + NAND_CTRL_CLE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + /* We cant' use dev_ready here, but at least we wait for the + * command to complete + */ + udelay(50); ret = this->read_byte(mtd) << 8; ret |= this->read_byte(mtd); @@ -426,12 +429,13 @@ static uint16_t __init doc200x_ident_chip(struct mtd_info *mtd, int nr) } ident; void __iomem *docptr = doc->virtadr; - doc200x_hwcontrol(mtd, NAND_CTL_SETCLE); - doc2000_write_byte(mtd, NAND_CMD_READID); - doc200x_hwcontrol(mtd, NAND_CTL_CLRCLE); - doc200x_hwcontrol(mtd, NAND_CTL_SETALE); - doc2000_write_byte(mtd, 0); - doc200x_hwcontrol(mtd, NAND_CTL_CLRALE); + doc200x_hwcontrol(mtd, NAND_CMD_READID, + NAND_CTRL_CLE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + + udelay(50); ident.dword = readl(docptr + DoC_2k_CDSN_IO); if (((ident.byte[0] << 8) | ident.byte[1]) == ret) { @@ -465,7 +469,7 @@ static void __init doc2000_count_chips(struct mtd_info *mtd) printk(KERN_DEBUG "Detected %d chips per floor.\n", i); } -static int doc200x_wait(struct mtd_info *mtd, struct nand_chip *this, int state) +static int doc200x_wait(struct mtd_info *mtd, struct nand_chip *this) { struct doc_priv *doc = this->priv; @@ -496,30 +500,28 @@ static u_char doc2001_read_byte(struct mtd_info *mtd) struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; - /*ReadDOC(docptr, CDSNSlowIO); */ + //ReadDOC(docptr, CDSNSlowIO); /* 11.4.5 -- delay twice to allow extended length cycle */ DoC_Delay(doc, 2); ReadDOC(docptr, ReadPipeInit); - /*return ReadDOC(docptr, Mil_CDSN_IO); */ + //return ReadDOC(docptr, Mil_CDSN_IO); return ReadDOC(docptr, LastDataRead); } -static void doc2001_writebuf(struct mtd_info *mtd, - const u_char *buf, int len) +static void doc2001_writebuf(struct mtd_info *mtd, const u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - for (i=0; i < len; i++) + for (i = 0; i < len; i++) WriteDOC_(buf[i], docptr, DoC_Mil_CDSN_IO + i); /* Terminate write pipeline */ WriteDOC(0x00, docptr, WritePipeTerm); } -static void doc2001_readbuf(struct mtd_info *mtd, - u_char *buf, int len) +static void doc2001_readbuf(struct mtd_info *mtd, u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; @@ -529,15 +531,14 @@ static void doc2001_readbuf(struct mtd_info *mtd, /* Start read pipeline */ ReadDOC(docptr, ReadPipeInit); - for (i=0; i < len-1; i++) + for (i = 0; i < len - 1; i++) buf[i] = ReadDOC(docptr, Mil_CDSN_IO + (i & 0xff)); /* Terminate read pipeline */ buf[i] = ReadDOC(docptr, LastDataRead); } -static int doc2001_verifybuf(struct mtd_info *mtd, - const u_char *buf, int len) +static int doc2001_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; @@ -547,7 +548,7 @@ static int doc2001_verifybuf(struct mtd_info *mtd, /* Start read pipeline */ ReadDOC(docptr, ReadPipeInit); - for (i=0; i < len-1; i++) + for (i = 0; i < len - 1; i++) if (buf[i] != ReadDOC(docptr, Mil_CDSN_IO)) { ReadDOC(docptr, LastDataRead); return i; @@ -567,81 +568,84 @@ static u_char doc2001plus_read_byte(struct mtd_info *mtd) ReadDOC(docptr, Mplus_ReadPipeInit); ReadDOC(docptr, Mplus_ReadPipeInit); ret = ReadDOC(docptr, Mplus_LastDataRead); - if (debug) printk("read_byte returns %02x\n", ret); + if (debug) + printk("read_byte returns %02x\n", ret); return ret; } -static void doc2001plus_writebuf(struct mtd_info *mtd, - const u_char *buf, int len) +static void doc2001plus_writebuf(struct mtd_info *mtd, const u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - if (debug)printk("writebuf of %d bytes: ", len); - for (i=0; i < len; i++) { + if (debug) + printk("writebuf of %d bytes: ", len); + for (i = 0; i < len; i++) { WriteDOC_(buf[i], docptr, DoC_Mil_CDSN_IO + i); if (debug && i < 16) printk("%02x ", buf[i]); } - if (debug) printk("\n"); + if (debug) + printk("\n"); } -static void doc2001plus_readbuf(struct mtd_info *mtd, - u_char *buf, int len) +static void doc2001plus_readbuf(struct mtd_info *mtd, u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - if (debug)printk("readbuf of %d bytes: ", len); + if (debug) + printk("readbuf of %d bytes: ", len); /* Start read pipeline */ ReadDOC(docptr, Mplus_ReadPipeInit); ReadDOC(docptr, Mplus_ReadPipeInit); - for (i=0; i < len-2; i++) { + for (i = 0; i < len - 2; i++) { buf[i] = ReadDOC(docptr, Mil_CDSN_IO); if (debug && i < 16) printk("%02x ", buf[i]); } /* Terminate read pipeline */ - buf[len-2] = ReadDOC(docptr, Mplus_LastDataRead); + buf[len - 2] = ReadDOC(docptr, Mplus_LastDataRead); if (debug && i < 16) - printk("%02x ", buf[len-2]); - buf[len-1] = ReadDOC(docptr, Mplus_LastDataRead); + printk("%02x ", buf[len - 2]); + buf[len - 1] = ReadDOC(docptr, Mplus_LastDataRead); if (debug && i < 16) - printk("%02x ", buf[len-1]); - if (debug) printk("\n"); + printk("%02x ", buf[len - 1]); + if (debug) + printk("\n"); } -static int doc2001plus_verifybuf(struct mtd_info *mtd, - const u_char *buf, int len) +static int doc2001plus_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; int i; - if (debug)printk("verifybuf of %d bytes: ", len); + if (debug) + printk("verifybuf of %d bytes: ", len); /* Start read pipeline */ ReadDOC(docptr, Mplus_ReadPipeInit); ReadDOC(docptr, Mplus_ReadPipeInit); - for (i=0; i < len-2; i++) + for (i = 0; i < len - 2; i++) if (buf[i] != ReadDOC(docptr, Mil_CDSN_IO)) { ReadDOC(docptr, Mplus_LastDataRead); ReadDOC(docptr, Mplus_LastDataRead); return i; } - if (buf[len-2] != ReadDOC(docptr, Mplus_LastDataRead)) - return len-2; - if (buf[len-1] != ReadDOC(docptr, Mplus_LastDataRead)) - return len-1; + if (buf[len - 2] != ReadDOC(docptr, Mplus_LastDataRead)) + return len - 2; + if (buf[len - 1] != ReadDOC(docptr, Mplus_LastDataRead)) + return len - 1; return 0; } @@ -652,7 +656,8 @@ static void doc2001plus_select_chip(struct mtd_info *mtd, int chip) void __iomem *docptr = doc->virtadr; int floor = 0; - if(debug)printk("select chip (%d)\n", chip); + if (debug) + printk("select chip (%d)\n", chip); if (chip == -1) { /* Disable flash internally */ @@ -661,7 +666,7 @@ static void doc2001plus_select_chip(struct mtd_info *mtd, int chip) } floor = chip / doc->chips_per_floor; - chip -= (floor * doc->chips_per_floor); + chip -= (floor * doc->chips_per_floor); /* Assert ChipEnable and deassert WriteProtect */ WriteDOC((DOC_FLASH_CE), docptr, Mplus_FlashSelect); @@ -678,65 +683,54 @@ static void doc200x_select_chip(struct mtd_info *mtd, int chip) void __iomem *docptr = doc->virtadr; int floor = 0; - if(debug)printk("select chip (%d)\n", chip); + if (debug) + printk("select chip (%d)\n", chip); if (chip == -1) return; floor = chip / doc->chips_per_floor; - chip -= (floor * doc->chips_per_floor); + chip -= (floor * doc->chips_per_floor); /* 11.4.4 -- deassert CE before changing chip */ - doc200x_hwcontrol(mtd, NAND_CTL_CLRNCE); + doc200x_hwcontrol(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); WriteDOC(floor, docptr, FloorSelect); WriteDOC(chip, docptr, CDSNDeviceSelect); - doc200x_hwcontrol(mtd, NAND_CTL_SETNCE); + doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); doc->curchip = chip; doc->curfloor = floor; } -static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd) +#define CDSN_CTRL_MSK (CDSN_CTRL_CE | CDSN_CTRL_CLE | CDSN_CTRL_ALE) + +static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; - switch(cmd) { - case NAND_CTL_SETNCE: - doc->CDSNControl |= CDSN_CTRL_CE; - break; - case NAND_CTL_CLRNCE: - doc->CDSNControl &= ~CDSN_CTRL_CE; - break; - case NAND_CTL_SETCLE: - doc->CDSNControl |= CDSN_CTRL_CLE; - break; - case NAND_CTL_CLRCLE: - doc->CDSNControl &= ~CDSN_CTRL_CLE; - break; - case NAND_CTL_SETALE: - doc->CDSNControl |= CDSN_CTRL_ALE; - break; - case NAND_CTL_CLRALE: - doc->CDSNControl &= ~CDSN_CTRL_ALE; - break; - case NAND_CTL_SETWP: - doc->CDSNControl |= CDSN_CTRL_WP; - break; - case NAND_CTL_CLRWP: - doc->CDSNControl &= ~CDSN_CTRL_WP; - break; + if (ctrl & NAND_CTRL_CHANGE) { + doc->CDSNControl &= ~CDSN_CTRL_MSK; + doc->CDSNControl |= ctrl & CDSN_CTRL_MSK; + if (debug) + printk("hwcontrol(%d): %02x\n", cmd, doc->CDSNControl); + WriteDOC(doc->CDSNControl, docptr, CDSNControl); + /* 11.4.3 -- 4 NOPs after CSDNControl write */ + DoC_Delay(doc, 4); + } + if (cmd != NAND_CMD_NONE) { + if (DoC_is_2000(doc)) + doc2000_write_byte(mtd, cmd); + else + doc2001_write_byte(mtd, cmd); } - if (debug)printk("hwcontrol(%d): %02x\n", cmd, doc->CDSNControl); - WriteDOC(doc->CDSNControl, docptr, CDSNControl); - /* 11.4.3 -- 4 NOPs after CSDNControl write */ - DoC_Delay(doc, 4); } -static void doc2001plus_command (struct mtd_info *mtd, unsigned command, int column, int page_addr) +static void doc2001plus_command(struct mtd_info *mtd, unsigned command, int column, int page_addr) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; @@ -757,9 +751,9 @@ static void doc2001plus_command (struct mtd_info *mtd, unsigned command, int col if (command == NAND_CMD_SEQIN) { int readcmd; - if (column >= mtd->oobblock) { + if (column >= mtd->writesize) { /* OOB area */ - column -= mtd->oobblock; + column -= mtd->writesize; readcmd = NAND_CMD_READOOB; } else if (column < 256) { /* First 256 bytes --> READ0 */ @@ -783,25 +777,26 @@ static void doc2001plus_command (struct mtd_info *mtd, unsigned command, int col WriteDOC(column, docptr, Mplus_FlashAddress); } if (page_addr != -1) { - WriteDOC((unsigned char) (page_addr & 0xff), docptr, Mplus_FlashAddress); - WriteDOC((unsigned char) ((page_addr >> 8) & 0xff), docptr, Mplus_FlashAddress); + WriteDOC((unsigned char)(page_addr & 0xff), docptr, Mplus_FlashAddress); + WriteDOC((unsigned char)((page_addr >> 8) & 0xff), docptr, Mplus_FlashAddress); /* One more address cycle for higher density devices */ if (this->chipsize & 0x0c000000) { - WriteDOC((unsigned char) ((page_addr >> 16) & 0x0f), docptr, Mplus_FlashAddress); + WriteDOC((unsigned char)((page_addr >> 16) & 0x0f), docptr, Mplus_FlashAddress); printk("high density\n"); } } WriteDOC(0, docptr, Mplus_WritePipeTerm); WriteDOC(0, docptr, Mplus_WritePipeTerm); /* deassert ALE */ - if (command == NAND_CMD_READ0 || command == NAND_CMD_READ1 || command == NAND_CMD_READOOB || command == NAND_CMD_READID) + if (command == NAND_CMD_READ0 || command == NAND_CMD_READ1 || + command == NAND_CMD_READOOB || command == NAND_CMD_READID) WriteDOC(0, docptr, Mplus_FlashControl); } /* * program and erase have their own busy handlers * status and sequential in needs no delay - */ + */ switch (command) { case NAND_CMD_PAGEPROG: @@ -818,26 +813,26 @@ static void doc2001plus_command (struct mtd_info *mtd, unsigned command, int col WriteDOC(NAND_CMD_STATUS, docptr, Mplus_FlashCmd); WriteDOC(0, docptr, Mplus_WritePipeTerm); WriteDOC(0, docptr, Mplus_WritePipeTerm); - while ( !(this->read_byte(mtd) & 0x40)); + while (!(this->read_byte(mtd) & 0x40)) ; return; - /* This applies to read commands */ + /* This applies to read commands */ default: /* * If we don't have access to the busy pin, we apply the given * command delay - */ + */ if (!this->dev_ready) { - udelay (this->chip_delay); + udelay(this->chip_delay); return; } } /* Apply this short delay always to ensure that we do wait tWB in * any case on any machine. */ - ndelay (100); + ndelay(100); /* wait until command is processed */ - while (!this->dev_ready(mtd)); + while (!this->dev_ready(mtd)) ; } static int doc200x_dev_ready(struct mtd_info *mtd) @@ -850,23 +845,25 @@ static int doc200x_dev_ready(struct mtd_info *mtd) /* 11.4.2 -- must NOP four times before checking FR/B# */ DoC_Delay(doc, 4); if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) { - if(debug) + if (debug) printk("not ready\n"); return 0; } - if (debug)printk("was ready\n"); + if (debug) + printk("was ready\n"); return 1; } else { /* 11.4.2 -- must NOP four times before checking FR/B# */ DoC_Delay(doc, 4); if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { - if(debug) + if (debug) printk("not ready\n"); return 0; } /* 11.4.2 -- Must NOP twice if it's ready */ DoC_Delay(doc, 2); - if (debug)printk("was ready\n"); + if (debug) + printk("was ready\n"); return 1; } } @@ -885,7 +882,7 @@ static void doc200x_enable_hwecc(struct mtd_info *mtd, int mode) void __iomem *docptr = doc->virtadr; /* Prime the ECC engine */ - switch(mode) { + switch (mode) { case NAND_ECC_READ: WriteDOC(DOC_ECC_RESET, docptr, ECCConf); WriteDOC(DOC_ECC_EN, docptr, ECCConf); @@ -904,7 +901,7 @@ static void doc2001plus_enable_hwecc(struct mtd_info *mtd, int mode) void __iomem *docptr = doc->virtadr; /* Prime the ECC engine */ - switch(mode) { + switch (mode) { case NAND_ECC_READ: WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); WriteDOC(DOC_ECC_EN, docptr, Mplus_ECCConf); @@ -917,8 +914,7 @@ static void doc2001plus_enable_hwecc(struct mtd_info *mtd, int mode) } /* This code is only called on write */ -static int doc200x_calculate_ecc(struct mtd_info *mtd, const u_char *dat, - unsigned char *ecc_code) +static int doc200x_calculate_ecc(struct mtd_info *mtd, const u_char *dat, unsigned char *ecc_code) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; @@ -962,7 +958,8 @@ static int doc200x_calculate_ecc(struct mtd_info *mtd, const u_char *dat, often. It could be optimized away by examining the data in the writebuf routine, and remembering the result. */ for (i = 0; i < 512; i++) { - if (dat[i] == 0xff) continue; + if (dat[i] == 0xff) + continue; emptymatch = 0; break; } @@ -970,17 +967,20 @@ static int doc200x_calculate_ecc(struct mtd_info *mtd, const u_char *dat, /* If emptymatch still =1, we do have an all-0xff data buffer. Return all-0xff ecc value instead of the computed one, so it'll look just like a freshly-erased page. */ - if (emptymatch) memset(ecc_code, 0xff, 6); + if (emptymatch) + memset(ecc_code, 0xff, 6); #endif return 0; } -static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc) +static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *isnull) { int i, ret = 0; struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; void __iomem *docptr = doc->virtadr; + uint8_t calc_ecc[6]; volatile u_char dummy; int emptymatch = 1; @@ -1013,18 +1013,20 @@ static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ all-0xff data and stored ecc block. Check the stored ecc. */ if (emptymatch) { for (i = 0; i < 6; i++) { - if (read_ecc[i] == 0xff) continue; + if (read_ecc[i] == 0xff) + continue; emptymatch = 0; break; } } /* If emptymatch still =1, check the data block. */ if (emptymatch) { - /* Note: this somewhat expensive test should not be triggered - often. It could be optimized away by examining the data in - the readbuf routine, and remembering the result. */ + /* Note: this somewhat expensive test should not be triggered + often. It could be optimized away by examining the data in + the readbuf routine, and remembering the result. */ for (i = 0; i < 512; i++) { - if (dat[i] == 0xff) continue; + if (dat[i] == 0xff) + continue; emptymatch = 0; break; } @@ -1033,7 +1035,8 @@ static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ erased block, in which case the ECC will not come out right. We'll suppress the error and tell the caller everything's OK. Because it is. */ - if (!emptymatch) ret = doc_ecc_decode (rs_decoder, dat, calc_ecc); + if (!emptymatch) + ret = doc_ecc_decode(rs_decoder, dat, calc_ecc); if (ret > 0) printk(KERN_ERR "doc200x_correct_data corrected %d errors\n", ret); } @@ -1048,13 +1051,22 @@ static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ return ret; } -/*u_char mydatabuf[528]; */ - -static struct nand_oobinfo doc200x_oobinfo = { - .useecc = MTD_NANDECC_AUTOPLACE, +//u_char mydatabuf[528]; + +/* The strange out-of-order .oobfree list below is a (possibly unneeded) + * attempt to retain compatibility. It used to read: + * .oobfree = { {8, 8} } + * Since that leaves two bytes unusable, it was changed. But the following + * scheme might affect existing jffs2 installs by moving the cleanmarker: + * .oobfree = { {6, 10} } + * jffs2 seems to handle the above gracefully, but the current scheme seems + * safer. The only problem with it is that any code that parses oobfree must + * be able to handle out-of-order segments. + */ +static struct nand_ecclayout doc200x_oobinfo = { .eccbytes = 6, .eccpos = {0, 1, 2, 3, 4, 5}, - .oobfree = { {8, 8} } + .oobfree = {{8, 8}, {6, 2}} }; /* Find the (I)NFTL Media Header, and optionally also the mirror media header. @@ -1063,28 +1075,28 @@ static struct nand_oobinfo doc200x_oobinfo = { either "ANAND" or "BNAND". If findmirror=1, also look for the mirror media header. The page #s of the found media headers are placed in mh0_page and mh1_page in the DOC private structure. */ -static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, - const char *id, int findmirror) +static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, const char *id, int findmirror) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; - unsigned offs, end = (MAX_MEDIAHEADER_SCAN << this->phys_erase_shift); + unsigned offs; int ret; size_t retlen; - end = min(end, mtd->size); /* paranoia */ - for (offs = 0; offs < end; offs += mtd->erasesize) { - ret = mtd->read(mtd, offs, mtd->oobblock, &retlen, buf); - if (retlen != mtd->oobblock) continue; + for (offs = 0; offs < mtd->size; offs += mtd->erasesize) { + ret = mtd->read(mtd, offs, mtd->writesize, &retlen, buf); + if (retlen != mtd->writesize) + continue; if (ret) { - printk(KERN_WARNING "ECC error scanning DOC at 0x%x\n", - offs); + printk(KERN_WARNING "ECC error scanning DOC at 0x%x\n", offs); } - if (memcmp(buf, id, 6)) continue; + if (memcmp(buf, id, 6)) + continue; printk(KERN_INFO "Found DiskOnChip %s Media Header at 0x%x\n", id, offs); if (doc->mh0_page == -1) { doc->mh0_page = offs >> this->page_shift; - if (!findmirror) return 1; + if (!findmirror) + return 1; continue; } doc->mh1_page = offs >> this->page_shift; @@ -1097,8 +1109,8 @@ static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, /* Only one mediaheader was found. We want buf to contain a mediaheader on return, so we'll have to re-read the one we found. */ offs = doc->mh0_page << this->page_shift; - ret = mtd->read(mtd, offs, mtd->oobblock, &retlen, buf); - if (retlen != mtd->oobblock) { + ret = mtd->read(mtd, offs, mtd->writesize, &retlen, buf); + if (retlen != mtd->writesize) { /* Insanity. Give up. */ printk(KERN_ERR "Read DiskOnChip Media Header once, but can't reread it???\n"); return 0; @@ -1106,8 +1118,7 @@ static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, return 1; } -static inline int __init nftl_partscan(struct mtd_info *mtd, - struct mtd_partition *parts) +static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partition *parts) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; @@ -1115,19 +1126,23 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, u_char *buf; struct NFTLMediaHeader *mh; const unsigned psize = 1 << this->page_shift; + int numparts = 0; unsigned blocks, maxblocks; int offs, numheaders; - buf = kmalloc(mtd->oobblock, GFP_KERNEL); + buf = kmalloc(mtd->writesize, GFP_KERNEL); if (!buf) { printk(KERN_ERR "DiskOnChip mediaheader kmalloc failed!\n"); return 0; } - if (!(numheaders=find_media_headers(mtd, buf, "ANAND", 1))) goto out; - mh = (struct NFTLMediaHeader *) buf; + if (!(numheaders = find_media_headers(mtd, buf, "ANAND", 1))) + goto out; + mh = (struct NFTLMediaHeader *)buf; + + mh->NumEraseUnits = le16_to_cpu(mh->NumEraseUnits); + mh->FirstPhysicalEUN = le16_to_cpu(mh->FirstPhysicalEUN); + mh->FormattedSize = le32_to_cpu(mh->FormattedSize); -/*#ifdef CONFIG_MTD_DEBUG_VERBOSE */ -/* if (CONFIG_MTD_DEBUG_VERBOSE >= 2) */ printk(KERN_INFO " DataOrgID = %s\n" " NumEraseUnits = %d\n" " FirstPhysicalEUN = %d\n" @@ -1136,7 +1151,6 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, mh->DataOrgID, mh->NumEraseUnits, mh->FirstPhysicalEUN, mh->FormattedSize, mh->UnitSizeFactor); -/*#endif */ blocks = mtd->size >> this->phys_erase_shift; maxblocks = min(32768U, mtd->erasesize - psize); @@ -1145,8 +1159,8 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, /* Auto-determine UnitSizeFactor. The constraints are: - There can be at most 32768 virtual blocks. - There can be at most (virtual block size - page size) - virtual blocks (because MediaHeader+BBT must fit in 1). - */ + virtual blocks (because MediaHeader+BBT must fit in 1). + */ mh->UnitSizeFactor = 0xff; while (blocks > maxblocks) { blocks >>= 1; @@ -1179,31 +1193,35 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, offs <<= this->page_shift; offs += mtd->erasesize; - /*parts[0].name = " DiskOnChip Boot / Media Header partition"; */ - /*parts[0].offset = 0; */ - /*parts[0].size = offs; */ + if (show_firmware_partition == 1) { + parts[0].name = " DiskOnChip Firmware / Media Header partition"; + parts[0].offset = 0; + parts[0].size = offs; + numparts = 1; + } + + parts[numparts].name = " DiskOnChip BDTL partition"; + parts[numparts].offset = offs; + parts[numparts].size = (mh->NumEraseUnits - numheaders) << this->bbt_erase_shift; - parts[0].name = " DiskOnChip BDTL partition"; - parts[0].offset = offs; - parts[0].size = (mh->NumEraseUnits - numheaders) << this->bbt_erase_shift; + offs += parts[numparts].size; + numparts++; - offs += parts[0].size; if (offs < mtd->size) { - parts[1].name = " DiskOnChip Remainder partition"; - parts[1].offset = offs; - parts[1].size = mtd->size - offs; - ret = 2; - goto out; + parts[numparts].name = " DiskOnChip Remainder partition"; + parts[numparts].offset = offs; + parts[numparts].size = mtd->size - offs; + numparts++; } - ret = 1; -out: + + ret = numparts; + out: kfree(buf); return ret; } /* This is a stripped-down copy of the code in inftlmount.c */ -static inline int __init inftl_partscan(struct mtd_info *mtd, - struct mtd_partition *parts) +static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partition *parts) { struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; @@ -1220,15 +1238,16 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, if (inftl_bbt_write) end -= (INFTL_BBT_RESERVED_BLOCKS << this->phys_erase_shift); - buf = kmalloc(mtd->oobblock, GFP_KERNEL); + buf = kmalloc(mtd->writesize, GFP_KERNEL); if (!buf) { printk(KERN_ERR "DiskOnChip mediaheader kmalloc failed!\n"); return 0; } - if (!find_media_headers(mtd, buf, "BNAND", 0)) goto out; + if (!find_media_headers(mtd, buf, "BNAND", 0)) + goto out; doc->mh1_page = doc->mh0_page + (4096 >> this->page_shift); - mh = (struct INFTLMediaHeader *) buf; + mh = (struct INFTLMediaHeader *)buf; mh->NoOfBootImageBlocks = le32_to_cpu(mh->NoOfBootImageBlocks); mh->NoOfBinaryPartitions = le32_to_cpu(mh->NoOfBinaryPartitions); @@ -1237,8 +1256,6 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, mh->FormatFlags = le32_to_cpu(mh->FormatFlags); mh->PercentUsed = le32_to_cpu(mh->PercentUsed); -/*#ifdef CONFIG_MTD_DEBUG_VERBOSE */ -/* if (CONFIG_MTD_DEBUG_VERBOSE >= 2) */ printk(KERN_INFO " bootRecordID = %s\n" " NoOfBootImageBlocks = %d\n" " NoOfBinaryPartitions = %d\n" @@ -1256,7 +1273,6 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, ((unsigned char *) &mh->OsakVersion)[2] & 0xf, ((unsigned char *) &mh->OsakVersion)[3] & 0xf, mh->PercentUsed); -/*#endif */ vshift = this->phys_erase_shift + mh->BlockMultiplierBits; @@ -1282,8 +1298,6 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, ip->spareUnits = le32_to_cpu(ip->spareUnits); ip->Reserved0 = le32_to_cpu(ip->Reserved0); -/*#ifdef CONFIG_MTD_DEBUG_VERBOSE */ -/* if (CONFIG_MTD_DEBUG_VERBOSE >= 2) */ printk(KERN_INFO " PARTITION[%d] ->\n" " virtualUnits = %d\n" " firstUnit = %d\n" @@ -1293,16 +1307,14 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, i, ip->virtualUnits, ip->firstUnit, ip->lastUnit, ip->flags, ip->spareUnits); -/*#endif */ -/* - if ((i == 0) && (ip->firstUnit > 0)) { + if ((show_firmware_partition == 1) && + (i == 0) && (ip->firstUnit > 0)) { parts[0].name = " DiskOnChip IPL / Media Header partition"; parts[0].offset = 0; parts[0].size = mtd->erasesize * ip->firstUnit; numparts = 1; } -*/ if (ip->flags & INFTL_BINARY) parts[numparts].name = " DiskOnChip BDK partition"; @@ -1311,8 +1323,10 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, parts[numparts].offset = ip->firstUnit << vshift; parts[numparts].size = (1 + ip->lastUnit - ip->firstUnit) << vshift; numparts++; - if (ip->lastUnit > lastvunit) lastvunit = ip->lastUnit; - if (ip->flags & INFTL_LAST) break; + if (ip->lastUnit > lastvunit) + lastvunit = ip->lastUnit; + if (ip->flags & INFTL_LAST) + break; } lastvunit++; if ((lastvunit << vshift) < end) { @@ -1322,7 +1336,7 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, numparts++; } ret = numparts; -out: + out: kfree(buf); return ret; } @@ -1334,11 +1348,12 @@ static int __init nftl_scan_bbt(struct mtd_info *mtd) struct doc_priv *doc = this->priv; struct mtd_partition parts[2]; - memset((char *) parts, 0, sizeof(parts)); + memset((char *)parts, 0, sizeof(parts)); /* On NFTL, we have to find the media headers before we can read the BBTs, since they're stored in the media header eraseblocks. */ numparts = nftl_partscan(mtd, parts); - if (!numparts) return -EIO; + if (!numparts) + return -EIO; this->bbt_td->options = NAND_BBT_ABSPAGE | NAND_BBT_8BIT | NAND_BBT_SAVECONTENT | NAND_BBT_WRITE | NAND_BBT_VERSION; @@ -1385,8 +1400,7 @@ static int __init inftl_scan_bbt(struct mtd_info *mtd) this->bbt_td->pages[0] = 2; this->bbt_md = NULL; } else { - this->bbt_td->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | - NAND_BBT_VERSION; + this->bbt_td->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | NAND_BBT_VERSION; if (inftl_bbt_write) this->bbt_td->options |= NAND_BBT_WRITE; this->bbt_td->offs = 8; @@ -1396,8 +1410,7 @@ static int __init inftl_scan_bbt(struct mtd_info *mtd) this->bbt_td->reserved_block_code = 0x01; this->bbt_td->pattern = "MSYS_BBT"; - this->bbt_md->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | - NAND_BBT_VERSION; + this->bbt_md->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | NAND_BBT_VERSION; if (inftl_bbt_write) this->bbt_md->options |= NAND_BBT_WRITE; this->bbt_md->offs = 8; @@ -1412,12 +1425,13 @@ static int __init inftl_scan_bbt(struct mtd_info *mtd) At least as nand_bbt.c is currently written. */ if ((ret = nand_scan_bbt(mtd, NULL))) return ret; - memset((char *) parts, 0, sizeof(parts)); + memset((char *)parts, 0, sizeof(parts)); numparts = inftl_partscan(mtd, parts); /* At least for now, require the INFTL Media Header. We could probably do without it for non-INFTL use, since all it gives us is autopartitioning, but I want to give it more thought. */ - if (!numparts) return -EIO; + if (!numparts) + return -EIO; add_mtd_device(mtd); #ifdef CONFIG_MTD_PARTITIONS if (!no_autopart) @@ -1431,7 +1445,6 @@ static inline int __init doc2000_init(struct mtd_info *mtd) struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; - this->write_byte = doc2000_write_byte; this->read_byte = doc2000_read_byte; this->write_buf = doc2000_writebuf; this->read_buf = doc2000_readbuf; @@ -1449,7 +1462,6 @@ static inline int __init doc2001_init(struct mtd_info *mtd) struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; - this->write_byte = doc2001_write_byte; this->read_byte = doc2001_read_byte; this->write_buf = doc2001_writebuf; this->read_buf = doc2001_readbuf; @@ -1481,16 +1493,15 @@ static inline int __init doc2001plus_init(struct mtd_info *mtd) struct nand_chip *this = mtd->priv; struct doc_priv *doc = this->priv; - this->write_byte = NULL; this->read_byte = doc2001plus_read_byte; this->write_buf = doc2001plus_writebuf; this->read_buf = doc2001plus_readbuf; this->verify_buf = doc2001plus_verifybuf; this->scan_bbt = inftl_scan_bbt; - this->hwcontrol = NULL; + this->cmd_ctrl = NULL; this->select_chip = doc2001plus_select_chip; this->cmdfunc = doc2001plus_command; - this->enable_hwecc = doc2001plus_enable_hwecc; + this->ecc.hwctl = doc2001plus_enable_hwecc; doc->chips_per_floor = 1; mtd->name = "DiskOnChip Millennium Plus"; @@ -1498,7 +1509,7 @@ static inline int __init doc2001plus_init(struct mtd_info *mtd) return 1; } -static inline int __init doc_probe(unsigned long physadr) +static int __init doc_probe(unsigned long physadr) { unsigned char ChipID; struct mtd_info *mtd; @@ -1527,20 +1538,16 @@ static inline int __init doc_probe(unsigned long physadr) save_control = ReadDOC(virtadr, DOCControl); /* Reset the DiskOnChip ASIC */ - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, - virtadr, DOCControl); - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, - virtadr, DOCControl); + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, virtadr, DOCControl); + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, virtadr, DOCControl); /* Enable the DiskOnChip ASIC */ - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, - virtadr, DOCControl); - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, - virtadr, DOCControl); + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, virtadr, DOCControl); + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, virtadr, DOCControl); ChipID = ReadDOC(virtadr, ChipID); - switch(ChipID) { + switch (ChipID) { case DOC_ChipID_Doc2k: reg = DoC_2k_ECCStatus; break; @@ -1556,15 +1563,13 @@ static inline int __init doc_probe(unsigned long physadr) ReadDOC(virtadr, Mplus_Power); /* Reset the Millennium Plus ASIC */ - tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | - DOC_MODE_BDECT; + tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | DOC_MODE_BDECT; WriteDOC(tmp, virtadr, Mplus_DOCControl); WriteDOC(~tmp, virtadr, Mplus_CtrlConfirm); mdelay(1); /* Enable the Millennium Plus ASIC */ - tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | - DOC_MODE_BDECT; + tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | DOC_MODE_BDECT; WriteDOC(tmp, virtadr, Mplus_DOCControl); WriteDOC(~tmp, virtadr, Mplus_CtrlConfirm); mdelay(1); @@ -1588,7 +1593,7 @@ static inline int __init doc_probe(unsigned long physadr) goto notfound; } /* Check the TOGGLE bit in the ECC register */ - tmp = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; + tmp = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; tmpb = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; tmpc = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; if ((tmp == tmpb) || (tmp != tmpc)) { @@ -1618,11 +1623,11 @@ static inline int __init doc_probe(unsigned long physadr) if (ChipID == DOC_ChipID_DocMilPlus16) { WriteDOC(~newval, virtadr, Mplus_AliasResolution); oldval = ReadDOC(doc->virtadr, Mplus_AliasResolution); - WriteDOC(newval, virtadr, Mplus_AliasResolution); /* restore it */ + WriteDOC(newval, virtadr, Mplus_AliasResolution); // restore it } else { WriteDOC(~newval, virtadr, AliasResolution); oldval = ReadDOC(doc->virtadr, AliasResolution); - WriteDOC(newval, virtadr, AliasResolution); /* restore it */ + WriteDOC(newval, virtadr, AliasResolution); // restore it } newval = ~newval; if (oldval == newval) { @@ -1634,16 +1639,13 @@ static inline int __init doc_probe(unsigned long physadr) printk(KERN_NOTICE "DiskOnChip found at 0x%lx\n", physadr); len = sizeof(struct mtd_info) + - sizeof(struct nand_chip) + - sizeof(struct doc_priv) + - (2 * sizeof(struct nand_bbt_descr)); - mtd = kmalloc(len, GFP_KERNEL); + sizeof(struct nand_chip) + sizeof(struct doc_priv) + (2 * sizeof(struct nand_bbt_descr)); + mtd = kzalloc(len, GFP_KERNEL); if (!mtd) { printk(KERN_ERR "DiskOnChip kmalloc (%d bytes) failed!\n", len); ret = -ENOMEM; goto fail; } - memset(mtd, 0, len); nand = (struct nand_chip *) (mtd + 1); doc = (struct doc_priv *) (nand + 1); @@ -1655,17 +1657,19 @@ static inline int __init doc_probe(unsigned long physadr) nand->priv = doc; nand->select_chip = doc200x_select_chip; - nand->hwcontrol = doc200x_hwcontrol; + nand->cmd_ctrl = doc200x_hwcontrol; nand->dev_ready = doc200x_dev_ready; nand->waitfunc = doc200x_wait; nand->block_bad = doc200x_block_bad; - nand->enable_hwecc = doc200x_enable_hwecc; - nand->calculate_ecc = doc200x_calculate_ecc; - nand->correct_data = doc200x_correct_data; + nand->ecc.hwctl = doc200x_enable_hwecc; + nand->ecc.calculate = doc200x_calculate_ecc; + nand->ecc.correct = doc200x_correct_data; - nand->autooob = &doc200x_oobinfo; - nand->eccmode = NAND_ECC_HW6_512; - nand->options = NAND_USE_FLASH_BBT | NAND_HWECC_SYNDROME; + nand->ecc.layout = &doc200x_oobinfo; + nand->ecc.mode = NAND_ECC_HW_SYNDROME; + nand->ecc.size = 512; + nand->ecc.bytes = 6; + nand->options = NAND_USE_FLASH_BBT; doc->physadr = physadr; doc->virtadr = virtadr; @@ -1699,11 +1703,11 @@ static inline int __init doc_probe(unsigned long physadr) doclist = mtd; return 0; -notfound: + notfound: /* Put back the contents of the DOCControl register, in case it's not actually a DiskOnChip. */ WriteDOC(save_control, virtadr, DOCControl); -fail: + fail: iounmap(virtadr); return ret; } @@ -1740,7 +1744,7 @@ static int __init init_nanddoc(void) */ rs_decoder = init_rs(10, 0x409, FCR, 1, NROOTS); if (!rs_decoder) { - printk (KERN_ERR "DiskOnChip: Could not create a RS decoder\n"); + printk(KERN_ERR "DiskOnChip: Could not create a RS decoder\n"); return -ENOMEM; } @@ -1750,7 +1754,7 @@ static int __init init_nanddoc(void) if (ret < 0) goto outerr; } else { - for (i=0; (doc_locations[i] != 0xffffffff); i++) { + for (i = 0; (doc_locations[i] != 0xffffffff); i++) { doc_probe(doc_locations[i]); } } @@ -1762,7 +1766,7 @@ static int __init init_nanddoc(void) goto outerr; } return 0; -outerr: + outerr: free_rs(rs_decoder); return ret; } diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 6416d1529e..aeb179731d 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -10,39 +10,21 @@ * http://www.linux-mtd.infradead.org/tech/nand.html * * Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com) - * 2002 Thomas Gleixner (tglx@linutronix.de) + * 2002-2006 Thomas Gleixner (tglx@linutronix.de) * - * 02-08-2004 tglx: support for strange chips, which cannot auto increment - * pages on read / read_oob - * - * 03-17-2004 tglx: Check ready before auto increment check. Simon Bayes - * pointed this out, as he marked an auto increment capable chip - * as NOAUTOINCR in the board driver. - * Make reads over block boundaries work too - * - * 04-14-2004 tglx: first working version for 2k page size chips - * - * 05-19-2004 tglx: Basic support for Renesas AG-AND chips - * - * 09-24-2004 tglx: add support for hardware controllers (e.g. ECC) shared - * among multiple independend devices. Suggestions and initial patch - * from Ben Dooks - * - * Credits: + * Credits: * David Woodhouse for adding multichip support * * Aleph One Ltd. and Toby Churchill Ltd. for supporting the * rework for 2K page size chips * - * TODO: + * TODO: * Enable cached programming for 2k page size chips * Check, if mtd->ecctype should be set to MTD_ECC_HW * if we have HW ecc support. * The AG-AND chips have nice features for speed improvement, * which are not supported yet. Read / program 4 pages in one go. * - * $Id: nand_base.c,v 1.126 2004/12/13 11:22:25 lavinen Exp $ - * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. @@ -51,8 +33,10 @@ /* XXX U-BOOT XXX */ #if 0 +#include #include #include +#include #include #include #include @@ -62,6 +46,7 @@ #include #include #include +#include #include #ifdef CONFIG_MTD_PARTITIONS @@ -72,10 +57,13 @@ #include +#define ENOTSUPP 524 /* Operation is not supported */ + #if defined(CONFIG_CMD_NAND) && !defined(CFG_NAND_LEGACY) #include #include +#include #include #include #include @@ -89,83 +77,67 @@ #endif /* Define default oob placement schemes for large and small page devices */ -static struct nand_oobinfo nand_oob_8 = { - .useecc = MTD_NANDECC_AUTOPLACE, +static struct nand_ecclayout nand_oob_8 = { .eccbytes = 3, .eccpos = {0, 1, 2}, - .oobfree = { {3, 2}, {6, 2} } + .oobfree = { + {.offset = 3, + .length = 2}, + {.offset = 6, + .length = 2}} }; -static struct nand_oobinfo nand_oob_16 = { - .useecc = MTD_NANDECC_AUTOPLACE, +static struct nand_ecclayout nand_oob_16 = { .eccbytes = 6, .eccpos = {0, 1, 2, 3, 6, 7}, - .oobfree = { {8, 8} } + .oobfree = { + {.offset = 8, + . length = 8}} }; -static struct nand_oobinfo nand_oob_64 = { - .useecc = MTD_NANDECC_AUTOPLACE, +static struct nand_ecclayout nand_oob_64 = { .eccbytes = 24, .eccpos = { - 40, 41, 42, 43, 44, 45, 46, 47, - 48, 49, 50, 51, 52, 53, 54, 55, - 56, 57, 58, 59, 60, 61, 62, 63}, - .oobfree = { {2, 38} } + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { + {.offset = 2, + .length = 38}} }; -static struct nand_oobinfo nand_oob_128 = { - .useecc = MTD_NANDECC_AUTOPLACE, +static struct nand_ecclayout nand_oob_128 = { .eccbytes = 48, .eccpos = { - 80, 81, 82, 83, 84, 85, 86, 87, - 88, 89, 90, 91, 92, 93, 94, 95, - 96, 97, 98, 99, 100, 101, 102, 103, - 104, 105, 106, 107, 108, 109, 110, 111, - 112, 113, 114, 115, 116, 117, 118, 119, - 120, 121, 122, 123, 124, 125, 126, 127}, - .oobfree = { {2, 78} } + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127}, + .oobfree = { + {.offset = 2, + .length = 78}} }; -/* This is used for padding purposes in nand_write_oob */ -static u_char *ffchars; + +static int nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, + int new_state); + +static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops); + +static int nand_wait(struct mtd_info *mtd, struct nand_chip *this); /* - * NAND low-level MTD interface functions + * For devices which display every fart in the system on a seperate LED. Is + * compiled away when LED support is disabled. */ -static void nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len); -static void nand_read_buf(struct mtd_info *mtd, u_char *buf, int len); -static int nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len); - -static int nand_read (struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, u_char * buf); -static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, - size_t * retlen, u_char * buf, u_char * eccbuf, struct nand_oobinfo *oobsel); -static int nand_read_oob (struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, u_char * buf); -static int nand_write (struct mtd_info *mtd, loff_t to, size_t len, size_t * retlen, const u_char * buf); -static int nand_write_ecc (struct mtd_info *mtd, loff_t to, size_t len, - size_t * retlen, const u_char * buf, u_char * eccbuf, struct nand_oobinfo *oobsel); -static int nand_write_oob (struct mtd_info *mtd, loff_t to, size_t len, size_t * retlen, const u_char *buf); /* XXX U-BOOT XXX */ #if 0 -static int nand_writev (struct mtd_info *mtd, const struct kvec *vecs, - unsigned long count, loff_t to, size_t * retlen); -static int nand_writev_ecc (struct mtd_info *mtd, const struct kvec *vecs, - unsigned long count, loff_t to, size_t * retlen, u_char *eccbuf, struct nand_oobinfo *oobsel); -#endif -static int nand_erase (struct mtd_info *mtd, struct erase_info *instr); -static void nand_sync (struct mtd_info *mtd); - -/* Some internal functions */ -static int nand_write_page (struct mtd_info *mtd, struct nand_chip *this, int page, u_char *oob_buf, - struct nand_oobinfo *oobsel, int mode); -#ifdef CONFIG_MTD_NAND_VERIFY_WRITE -static int nand_verify_pages (struct mtd_info *mtd, struct nand_chip *this, int page, int numpages, - u_char *oob_buf, struct nand_oobinfo *oobsel, int chipnr, int oobmode); -#else -#define nand_verify_pages(...) (0) +DEFINE_LED_TRIGGER(nand_led_trigger); #endif -static void nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int new_state); - /** * nand_release_device - [GENERIC] release chip * @mtd: MTD device structure @@ -174,33 +146,25 @@ static void nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int n */ /* XXX U-BOOT XXX */ #if 0 -static void nand_release_device (struct mtd_info *mtd) +static void nand_release_device(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; /* De-select the NAND device */ - this->select_chip(mtd, -1); - /* Do we have a hardware controller ? */ - if (this->controller) { - spin_lock(&this->controller->lock); - this->controller->active = NULL; - spin_unlock(&this->controller->lock); - } - /* Release the chip */ - spin_lock (&this->chip_lock); - this->state = FL_READY; - wake_up (&this->wq); - spin_unlock (&this->chip_lock); + chip->select_chip(mtd, -1); + + /* Release the controller and the chip */ + spin_lock(&chip->controller->lock); + chip->controller->active = NULL; + chip->state = FL_READY; + wake_up(&chip->controller->wq); + spin_unlock(&chip->controller->lock); } #else static void nand_release_device (struct mtd_info *mtd) { struct nand_chip *this = mtd->priv; this->select_chip(mtd, -1); /* De-select the NAND device */ - if (ffchars) { - kfree(ffchars); - ffchars = NULL; - } } #endif @@ -210,23 +174,10 @@ static void nand_release_device (struct mtd_info *mtd) * * Default read function for 8bit buswith */ -static u_char nand_read_byte(struct mtd_info *mtd) -{ - struct nand_chip *this = mtd->priv; - return readb(this->IO_ADDR_R); -} - -/** - * nand_write_byte - [DEFAULT] write one byte to the chip - * @mtd: MTD device structure - * @byte: pointer to data byte to write - * - * Default write function for 8it buswith - */ -static void nand_write_byte(struct mtd_info *mtd, u_char byte) +static uint8_t nand_read_byte(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; - writeb(byte, this->IO_ADDR_W); + struct nand_chip *chip = mtd->priv; + return readb(chip->IO_ADDR_R); } /** @@ -236,24 +187,10 @@ static void nand_write_byte(struct mtd_info *mtd, u_char byte) * Default read function for 16bit buswith with * endianess conversion */ -static u_char nand_read_byte16(struct mtd_info *mtd) -{ - struct nand_chip *this = mtd->priv; - return (u_char) cpu_to_le16(readw(this->IO_ADDR_R)); -} - -/** - * nand_write_byte16 - [DEFAULT] write one byte endianess aware to the chip - * @mtd: MTD device structure - * @byte: pointer to data byte to write - * - * Default write function for 16bit buswith with - * endianess conversion - */ -static void nand_write_byte16(struct mtd_info *mtd, u_char byte) +static uint8_t nand_read_byte16(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; - writew(le16_to_cpu((u16) byte), this->IO_ADDR_W); + struct nand_chip *chip = mtd->priv; + return (uint8_t) cpu_to_le16(readw(chip->IO_ADDR_R)); } /** @@ -265,40 +202,26 @@ static void nand_write_byte16(struct mtd_info *mtd, u_char byte) */ static u16 nand_read_word(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; - return readw(this->IO_ADDR_R); -} - -/** - * nand_write_word - [DEFAULT] write one word to the chip - * @mtd: MTD device structure - * @word: data word to write - * - * Default write function for 16bit buswith without - * endianess conversion - */ -static void nand_write_word(struct mtd_info *mtd, u16 word) -{ - struct nand_chip *this = mtd->priv; - writew(word, this->IO_ADDR_W); + struct nand_chip *chip = mtd->priv; + return readw(chip->IO_ADDR_R); } /** * nand_select_chip - [DEFAULT] control CE line * @mtd: MTD device structure - * @chip: chipnumber to select, -1 for deselect + * @chipnr: chipnumber to select, -1 for deselect * * Default select function for 1 chip devices. */ -static void nand_select_chip(struct mtd_info *mtd, int chip) +static void nand_select_chip(struct mtd_info *mtd, int chipnr) { - struct nand_chip *this = mtd->priv; - switch(chip) { + struct nand_chip *chip = mtd->priv; + + switch (chipnr) { case -1: - this->hwcontrol(mtd, NAND_CTL_CLRNCE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); break; case 0: - this->hwcontrol(mtd, NAND_CTL_SETNCE); break; default: @@ -314,13 +237,13 @@ static void nand_select_chip(struct mtd_info *mtd, int chip) * * Default write function for 8bit buswith */ -static void nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +static void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) { int i; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; - for (i=0; iIO_ADDR_W); + for (i = 0; i < len; i++) + writeb(buf[i], chip->IO_ADDR_W); } /** @@ -331,13 +254,13 @@ static void nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len) * * Default read function for 8bit buswith */ -static void nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) { int i; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; - for (i=0; iIO_ADDR_R); + for (i = 0; i < len; i++) + buf[i] = readb(chip->IO_ADDR_R); } /** @@ -348,15 +271,14 @@ static void nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) * * Default verify function for 8bit buswith */ -static int nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len) +static int nand_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len) { int i; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; - for (i=0; iIO_ADDR_R)) + for (i = 0; i < len; i++) + if (buf[i] != readb(chip->IO_ADDR_R)) return -EFAULT; - return 0; } @@ -368,15 +290,15 @@ static int nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len) * * Default write function for 16bit buswith */ -static void nand_write_buf16(struct mtd_info *mtd, const u_char *buf, int len) +static void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) { int i; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; u16 *p = (u16 *) buf; len >>= 1; - for (i=0; iIO_ADDR_W); + for (i = 0; i < len; i++) + writew(p[i], chip->IO_ADDR_W); } @@ -388,15 +310,15 @@ static void nand_write_buf16(struct mtd_info *mtd, const u_char *buf, int len) * * Default read function for 16bit buswith */ -static void nand_read_buf16(struct mtd_info *mtd, u_char *buf, int len) +static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len) { int i; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; u16 *p = (u16 *) buf; len >>= 1; - for (i=0; iIO_ADDR_R); + for (i = 0; i < len; i++) + p[i] = readw(chip->IO_ADDR_R); } /** @@ -407,15 +329,15 @@ static void nand_read_buf16(struct mtd_info *mtd, u_char *buf, int len) * * Default verify function for 16bit buswith */ -static int nand_verify_buf16(struct mtd_info *mtd, const u_char *buf, int len) +static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) { int i; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; u16 *p = (u16 *) buf; len >>= 1; - for (i=0; iIO_ADDR_R)) + for (i = 0; i < len; i++) + if (p[i] != readw(chip->IO_ADDR_R)) return -EFAULT; return 0; @@ -432,38 +354,36 @@ static int nand_verify_buf16(struct mtd_info *mtd, const u_char *buf, int len) static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) { int page, chipnr, res = 0; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; u16 bad; - page = (int)(ofs >> this->page_shift) & this->pagemask; + page = (int)(ofs >> chip->page_shift) & chip->pagemask; if (getchip) { - chipnr = (int)(ofs >> this->chip_shift); + chipnr = (int)(ofs >> chip->chip_shift); - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd, FL_READING); + nand_get_device(chip, mtd, FL_READING); /* Select the NAND device */ - this->select_chip(mtd, chipnr); + chip->select_chip(mtd, chipnr); } - if (this->options & NAND_BUSWIDTH_16) { - this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page); - bad = cpu_to_le16(this->read_word(mtd)); - if (this->badblockpos & 0x1) - bad >>= 1; + if (chip->options & NAND_BUSWIDTH_16) { + chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos & 0xFE, + page); + bad = cpu_to_le16(chip->read_word(mtd)); + if (chip->badblockpos & 0x1) + bad >>= 8; if ((bad & 0xFF) != 0xff) res = 1; } else { - this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page); - if (this->read_byte(mtd) != 0xff) + chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos, page); + if (chip->read_byte(mtd) != 0xff) res = 1; } - if (getchip) { - /* Deselect and wake up anyone waiting on the device */ + if (getchip) nand_release_device(mtd); - } return res; } @@ -478,22 +398,33 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) */ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs) { - struct nand_chip *this = mtd->priv; - u_char buf[2] = {0, 0}; - size_t retlen; - int block; + struct nand_chip *chip = mtd->priv; + uint8_t buf[2] = { 0, 0 }; + int block, ret; /* Get block number */ - block = ((int) ofs) >> this->bbt_erase_shift; - this->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1); + block = (int)(ofs >> chip->bbt_erase_shift); + if (chip->bbt) + chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1); /* Do we have a flash based bad block table ? */ - if (this->options & NAND_USE_FLASH_BBT) - return nand_update_bbt (mtd, ofs); + if (chip->options & NAND_USE_FLASH_BBT) + ret = nand_update_bbt(mtd, ofs); + else { + /* We write two bytes, so we dont have to mess with 16 bit + * access + */ + ofs += mtd->oobsize; + chip->ops.len = chip->ops.ooblen = 2; + chip->ops.datbuf = NULL; + chip->ops.oobbuf = buf; + chip->ops.ooboffs = chip->badblockpos & ~0x01; - /* We write two bytes, so we dont have to mess with 16 bit access */ - ofs += mtd->oobsize + (this->badblockpos & ~0x01); - return nand_write_oob (mtd, ofs , 2, &retlen, buf); + ret = nand_do_write_oob(mtd, ofs, &chip->ops); + } + if (!ret) + mtd->ecc_stats.badblocks++; + return ret; } /** @@ -503,12 +434,12 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs) * * The function expects, that the device is already selected */ -static int nand_check_wp (struct mtd_info *mtd) +static int nand_check_wp(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; /* Check the WP bit */ - this->cmdfunc (mtd, NAND_CMD_STATUS, -1, -1); - return (this->read_byte(mtd) & 0x80) ? 0 : 1; + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1; } /** @@ -521,16 +452,46 @@ static int nand_check_wp (struct mtd_info *mtd) * Check, if the block is bad. Either by reading the bad block table or * calling of the scan function. */ -static int nand_block_checkbad (struct mtd_info *mtd, loff_t ofs, int getchip, int allowbbt) +static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip, + int allowbbt) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; - if (!this->bbt) - return this->block_bad(mtd, ofs, getchip); + if (!chip->bbt) + return chip->block_bad(mtd, ofs, getchip); /* Return info from the table */ - return nand_isbad_bbt (mtd, ofs, allowbbt); + return nand_isbad_bbt(mtd, ofs, allowbbt); +} + +/* + * Wait for the ready pin, after a command + * The timeout is catched later. + */ +/* XXX U-BOOT XXX */ +#if 0 +void nand_wait_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + unsigned long timeo = jiffies + 2; + + led_trigger_event(nand_led_trigger, LED_FULL); + /* wait until command is processed or timeout occures */ + do { + if (chip->dev_ready(mtd)) + break; + touch_softlockup_watchdog(); + } while (time_before(jiffies, timeo)); + led_trigger_event(nand_led_trigger, LED_OFF); } +EXPORT_SYMBOL_GPL(nand_wait_ready); +#else +void nand_wait_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + nand_wait(mtd, chip); +} +#endif /** * nand_command - [DEFAULT] Send command to NAND device @@ -542,21 +503,21 @@ static int nand_block_checkbad (struct mtd_info *mtd, loff_t ofs, int getchip, i * Send command to NAND device. This function is used for small page * devices (256/512 Bytes per page) */ -static void nand_command (struct mtd_info *mtd, unsigned command, int column, int page_addr) +static void nand_command(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) { - register struct nand_chip *this = mtd->priv; + register struct nand_chip *chip = mtd->priv; + int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE; - /* Begin command latch cycle */ - this->hwcontrol(mtd, NAND_CTL_SETCLE); /* * Write out the command to the device. */ if (command == NAND_CMD_SEQIN) { int readcmd; - if (column >= mtd->oobblock) { + if (column >= mtd->writesize) { /* OOB area */ - column -= mtd->oobblock; + column -= mtd->writesize; readcmd = NAND_CMD_READOOB; } else if (column < 256) { /* First 256 bytes --> READ0 */ @@ -565,38 +526,37 @@ static void nand_command (struct mtd_info *mtd, unsigned command, int column, in column -= 256; readcmd = NAND_CMD_READ1; } - this->write_byte(mtd, readcmd); + chip->cmd_ctrl(mtd, readcmd, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; } - this->write_byte(mtd, command); + chip->cmd_ctrl(mtd, command, ctrl); - /* Set ALE and clear CLE to start address cycle */ - this->hwcontrol(mtd, NAND_CTL_CLRCLE); - - if (column != -1 || page_addr != -1) { - this->hwcontrol(mtd, NAND_CTL_SETALE); - - /* Serially input address */ - if (column != -1) { - /* Adjust columns for 16 bit buswidth */ - if (this->options & NAND_BUSWIDTH_16) - column >>= 1; - this->write_byte(mtd, column); - } - if (page_addr != -1) { - this->write_byte(mtd, (unsigned char) (page_addr & 0xff)); - this->write_byte(mtd, (unsigned char) ((page_addr >> 8) & 0xff)); - /* One more address cycle for devices > 32MiB */ - if (this->chipsize > (32 << 20)) - this->write_byte(mtd, (unsigned char) ((page_addr >> 16) & 0x0f)); - } - /* Latch in address */ - this->hwcontrol(mtd, NAND_CTL_CLRALE); + /* + * Address cycle, when necessary + */ + ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE; + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (chip->options & NAND_BUSWIDTH_16) + column >>= 1; + chip->cmd_ctrl(mtd, column, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; } + if (page_addr != -1) { + chip->cmd_ctrl(mtd, page_addr, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; + chip->cmd_ctrl(mtd, page_addr >> 8, ctrl); + /* One more address cycle for devices > 32MiB */ + if (chip->chipsize > (32 << 20)) + chip->cmd_ctrl(mtd, page_addr >> 16, ctrl); + } + chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); /* * program and erase have their own busy handlers * status and sequential in needs no delay - */ + */ switch (command) { case NAND_CMD_PAGEPROG: @@ -607,32 +567,32 @@ static void nand_command (struct mtd_info *mtd, unsigned command, int column, in return; case NAND_CMD_RESET: - if (this->dev_ready) + if (chip->dev_ready) break; - udelay(this->chip_delay); - this->hwcontrol(mtd, NAND_CTL_SETCLE); - this->write_byte(mtd, NAND_CMD_STATUS); - this->hwcontrol(mtd, NAND_CTL_CLRCLE); - while ( !(this->read_byte(mtd) & 0x40)); + udelay(chip->chip_delay); + chip->cmd_ctrl(mtd, NAND_CMD_STATUS, + NAND_CTRL_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, + NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ; return; - /* This applies to read commands */ + /* This applies to read commands */ default: /* * If we don't have access to the busy pin, we apply the given * command delay - */ - if (!this->dev_ready) { - udelay (this->chip_delay); + */ + if (!chip->dev_ready) { + udelay(chip->chip_delay); return; } } - /* Apply this short delay always to ensure that we do wait tWB in * any case on any machine. */ - ndelay (100); - /* wait until command is processed */ - while (!this->dev_ready(mtd)); + ndelay(100); + + nand_wait_ready(mtd); } /** @@ -642,55 +602,53 @@ static void nand_command (struct mtd_info *mtd, unsigned command, int column, in * @column: the column address for this command, -1 if none * @page_addr: the page address for this command, -1 if none * - * Send command to NAND device. This is the version for the new large page devices - * We dont have the seperate regions as we have in the small page devices. - * We must emulate NAND_CMD_READOOB to keep the code compatible. - * + * Send command to NAND device. This is the version for the new large page + * devices We dont have the separate regions as we have in the small page + * devices. We must emulate NAND_CMD_READOOB to keep the code compatible. */ -static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, int page_addr) +static void nand_command_lp(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) { - register struct nand_chip *this = mtd->priv; + register struct nand_chip *chip = mtd->priv; /* Emulate NAND_CMD_READOOB */ if (command == NAND_CMD_READOOB) { - column += mtd->oobblock; + column += mtd->writesize; command = NAND_CMD_READ0; } - - /* Begin command latch cycle */ - this->hwcontrol(mtd, NAND_CTL_SETCLE); - /* Write out the command to the device. */ - this->write_byte(mtd, command); - /* End command latch cycle */ - this->hwcontrol(mtd, NAND_CTL_CLRCLE); + /* Command latch cycle */ + chip->cmd_ctrl(mtd, command & 0xff, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); if (column != -1 || page_addr != -1) { - this->hwcontrol(mtd, NAND_CTL_SETALE); + int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE; /* Serially input address */ if (column != -1) { /* Adjust columns for 16 bit buswidth */ - if (this->options & NAND_BUSWIDTH_16) + if (chip->options & NAND_BUSWIDTH_16) column >>= 1; - this->write_byte(mtd, column & 0xff); - this->write_byte(mtd, column >> 8); + chip->cmd_ctrl(mtd, column, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; + chip->cmd_ctrl(mtd, column >> 8, ctrl); } if (page_addr != -1) { - this->write_byte(mtd, (unsigned char) (page_addr & 0xff)); - this->write_byte(mtd, (unsigned char) ((page_addr >> 8) & 0xff)); + chip->cmd_ctrl(mtd, page_addr, ctrl); + chip->cmd_ctrl(mtd, page_addr >> 8, + NAND_NCE | NAND_ALE); /* One more address cycle for devices > 128MiB */ - if (this->chipsize > (128 << 20)) - this->write_byte(mtd, (unsigned char) ((page_addr >> 16) & 0xff)); + if (chip->chipsize > (128 << 20)) + chip->cmd_ctrl(mtd, page_addr >> 16, + NAND_NCE | NAND_ALE); } - /* Latch in address */ - this->hwcontrol(mtd, NAND_CTL_CLRALE); } + chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); /* * program and erase have their own busy handlers - * status and sequential in needs no delay - */ + * status, sequential in, and deplete1 need no delay + */ switch (command) { case NAND_CMD_CACHEDPROG: @@ -698,51 +656,69 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, case NAND_CMD_ERASE1: case NAND_CMD_ERASE2: case NAND_CMD_SEQIN: + case NAND_CMD_RNDIN: case NAND_CMD_STATUS: + case NAND_CMD_DEPLETE1: return; + /* + * read error status commands require only a short delay + */ + case NAND_CMD_STATUS_ERROR: + case NAND_CMD_STATUS_ERROR0: + case NAND_CMD_STATUS_ERROR1: + case NAND_CMD_STATUS_ERROR2: + case NAND_CMD_STATUS_ERROR3: + udelay(chip->chip_delay); + return; case NAND_CMD_RESET: - if (this->dev_ready) + if (chip->dev_ready) break; - udelay(this->chip_delay); - this->hwcontrol(mtd, NAND_CTL_SETCLE); - this->write_byte(mtd, NAND_CMD_STATUS); - this->hwcontrol(mtd, NAND_CTL_CLRCLE); - while ( !(this->read_byte(mtd) & 0x40)); + udelay(chip->chip_delay); + chip->cmd_ctrl(mtd, NAND_CMD_STATUS, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ; + return; + + case NAND_CMD_RNDOUT: + /* No ready / busy check necessary */ + chip->cmd_ctrl(mtd, NAND_CMD_RNDOUTSTART, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); return; case NAND_CMD_READ0: - /* Begin command latch cycle */ - this->hwcontrol(mtd, NAND_CTL_SETCLE); - /* Write out the start read command */ - this->write_byte(mtd, NAND_CMD_READSTART); - /* End command latch cycle */ - this->hwcontrol(mtd, NAND_CTL_CLRCLE); - /* Fall through into ready check */ - - /* This applies to read commands */ + chip->cmd_ctrl(mtd, NAND_CMD_READSTART, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + + /* This applies to read commands */ default: /* * If we don't have access to the busy pin, we apply the given * command delay - */ - if (!this->dev_ready) { - udelay (this->chip_delay); + */ + if (!chip->dev_ready) { + udelay(chip->chip_delay); return; } } /* Apply this short delay always to ensure that we do wait tWB in * any case on any machine. */ - ndelay (100); - /* wait until command is processed */ - while (!this->dev_ready(mtd)); + ndelay(100); + + nand_wait_ready(mtd); } /** * nand_get_device - [GENERIC] Get chip for selected access - * @this: the nand chip descriptor + * @chip: the nand chip descriptor * @mtd: MTD device structure * @new_state: the state which is requested * @@ -750,100 +726,96 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, */ /* XXX U-BOOT XXX */ #if 0 -static void nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int new_state) +static int +nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state) { - struct nand_chip *active = this; - - DECLARE_WAITQUEUE (wait, current); + spinlock_t *lock = &chip->controller->lock; + wait_queue_head_t *wq = &chip->controller->wq; + DECLARE_WAITQUEUE(wait, current); + retry: + spin_lock(lock); - /* - * Grab the lock and see if the device is available - */ -retry: /* Hardware controller shared among independend devices */ - if (this->controller) { - spin_lock (&this->controller->lock); - if (this->controller->active) - active = this->controller->active; - else - this->controller->active = this; - spin_unlock (&this->controller->lock); - } + /* Hardware controller shared among independend devices */ + if (!chip->controller->active) + chip->controller->active = chip; - if (active == this) { - spin_lock (&this->chip_lock); - if (this->state == FL_READY) { - this->state = new_state; - spin_unlock (&this->chip_lock); - return; - } + if (chip->controller->active == chip && chip->state == FL_READY) { + chip->state = new_state; + spin_unlock(lock); + return 0; } - set_current_state (TASK_UNINTERRUPTIBLE); - add_wait_queue (&active->wq, &wait); - spin_unlock (&active->chip_lock); - schedule (); - remove_wait_queue (&active->wq, &wait); + if (new_state == FL_PM_SUSPENDED) { + spin_unlock(lock); + return (chip->state == FL_PM_SUSPENDED) ? 0 : -EAGAIN; + } + set_current_state(TASK_UNINTERRUPTIBLE); + add_wait_queue(wq, &wait); + spin_unlock(lock); + schedule(); + remove_wait_queue(wq, &wait); goto retry; } #else -static void nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int new_state) {} +static int nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int new_state) +{ + return 0; +} #endif /** * nand_wait - [DEFAULT] wait until the command is done * @mtd: MTD device structure - * @this: NAND chip structure - * @state: state to select the max. timeout value + * @chip: NAND chip structure * * Wait for command done. This applies to erase and program only * Erase can take up to 400ms and program up to 20ms according to * general NAND and SmartMedia specs - * -*/ + */ /* XXX U-BOOT XXX */ #if 0 -static int nand_wait(struct mtd_info *mtd, struct nand_chip *this, int state) +static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) { - unsigned long timeo = jiffies; - int status; + + unsigned long timeo = jiffies; + int status, state = chip->state; if (state == FL_ERASING) - timeo += (HZ * 400) / 1000; + timeo += (HZ * 400) / 1000; else - timeo += (HZ * 20) / 1000; + timeo += (HZ * 20) / 1000; + + led_trigger_event(nand_led_trigger, LED_FULL); /* Apply this short delay always to ensure that we do wait tWB in * any case on any machine. */ - ndelay (100); + ndelay(100); - if ((state == FL_ERASING) && (this->options & NAND_IS_AND)) - this->cmdfunc (mtd, NAND_CMD_STATUS_MULTI, -1, -1); + if ((state == FL_ERASING) && (chip->options & NAND_IS_AND)) + chip->cmdfunc(mtd, NAND_CMD_STATUS_MULTI, -1, -1); else - this->cmdfunc (mtd, NAND_CMD_STATUS, -1, -1); + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); while (time_before(jiffies, timeo)) { - /* Check, if we were interrupted */ - if (this->state != state) - return 0; - - if (this->dev_ready) { - if (this->dev_ready(mtd)) + if (chip->dev_ready) { + if (chip->dev_ready(mtd)) break; } else { - if (this->read_byte(mtd) & NAND_STATUS_READY) + if (chip->read_byte(mtd) & NAND_STATUS_READY) break; } - yield (); + cond_resched(); } - status = (int) this->read_byte(mtd); - return status; + led_trigger_event(nand_led_trigger, LED_OFF); - return 0; + status = (int)chip->read_byte(mtd); + return status; } #else -static int nand_wait(struct mtd_info *mtd, struct nand_chip *this, int state) +static int nand_wait(struct mtd_info *mtd, struct nand_chip *this) { unsigned long timeo; + int state = this->state; if (state == FL_ERASING) timeo = (CFG_HZ * 400) / 1000; @@ -881,1211 +853,1135 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *this, int state) #endif /** - * nand_write_page - [GENERIC] write one page - * @mtd: MTD device structure - * @this: NAND chip structure - * @page: startpage inside the chip, must be called with (page & this->pagemask) - * @oob_buf: out of band data buffer - * @oobsel: out of band selecttion structre - * @cached: 1 = enable cached programming if supported by chip - * - * Nand_page_program function is used for write and writev ! - * This function will always program a full page of data - * If you call it with a non page aligned buffer, you're lost :) - * - * Cached programming is not supported yet. + * nand_read_page_raw - [Intern] read raw page data without ecc + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data */ -static int nand_write_page (struct mtd_info *mtd, struct nand_chip *this, int page, - u_char *oob_buf, struct nand_oobinfo *oobsel, int cached) +static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf) { - int i, status; - u_char ecc_code[NAND_MAX_OOBSIZE]; - int eccmode = oobsel->useecc ? this->eccmode : NAND_ECC_NONE; - uint *oob_config = oobsel->eccpos; - int datidx = 0, eccidx = 0, eccsteps = this->eccsteps; - int eccbytes = 0; + chip->read_buf(mtd, buf, mtd->writesize); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} - /* FIXME: Enable cached programming */ - cached = 0; +/** + * nand_read_page_swecc - [REPLACABLE] software ecc based page read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + */ +static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; - /* Send command to begin auto page programming */ - this->cmdfunc (mtd, NAND_CMD_SEQIN, 0x00, page); + chip->ecc.read_page_raw(mtd, chip, buf); - /* Write out complete page of data, take care of eccmode */ - switch (eccmode) { - /* No ecc, write all */ - case NAND_ECC_NONE: - printk (KERN_WARNING "Writing data without ECC to NAND-FLASH is not recommended\n"); - this->write_buf(mtd, this->data_poi, mtd->oobblock); - break; + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) + chip->ecc.calculate(mtd, p, &ecc_calc[i]); - /* Software ecc 3/256, write all */ - case NAND_ECC_SOFT: - for (; eccsteps; eccsteps--) { - this->calculate_ecc(mtd, &this->data_poi[datidx], ecc_code); - for (i = 0; i < 3; i++, eccidx++) - oob_buf[oob_config[eccidx]] = ecc_code[i]; - datidx += this->eccsize; - } - this->write_buf(mtd, this->data_poi, mtd->oobblock); - break; - default: - eccbytes = this->eccbytes; - for (; eccsteps; eccsteps--) { - /* enable hardware ecc logic for write */ - this->enable_hwecc(mtd, NAND_ECC_WRITE); - this->write_buf(mtd, &this->data_poi[datidx], this->eccsize); - this->calculate_ecc(mtd, &this->data_poi[datidx], ecc_code); - for (i = 0; i < eccbytes; i++, eccidx++) - oob_buf[oob_config[eccidx]] = ecc_code[i]; - /* If the hardware ecc provides syndromes then - * the ecc code must be written immediately after - * the data bytes (words) */ - if (this->options & NAND_HWECC_SYNDROME) - this->write_buf(mtd, ecc_code, eccbytes); - datidx += this->eccsize; - } - break; - } + for (i = 0; i < chip->ecc.total; i++) + ecc_code[i] = chip->oob_poi[eccpos[i]]; - /* Write out OOB data */ - if (this->options & NAND_HWECC_SYNDROME) - this->write_buf(mtd, &oob_buf[oobsel->eccbytes], mtd->oobsize - oobsel->eccbytes); - else - this->write_buf(mtd, oob_buf, mtd->oobsize); - - /* Send command to actually program the data */ - this->cmdfunc (mtd, cached ? NAND_CMD_CACHEDPROG : NAND_CMD_PAGEPROG, -1, -1); - - if (!cached) { - /* call wait ready function */ - status = this->waitfunc (mtd, this, FL_WRITING); - /* See if device thinks it succeeded */ - if (status & 0x01) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "%s: Failed write, page 0x%08x, ", - __FUNCTION__, page); - return -EIO; - } - } else { - /* FIXME: Implement cached programming ! */ - /* wait until cache is ready*/ - /* status = this->waitfunc (mtd, this, FL_CACHEDRPG); */ + eccsteps = chip->ecc.steps; + p = buf; + + for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; + + stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); + if (stat == -1) + mtd->ecc_stats.failed++; + else + mtd->ecc_stats.corrected += stat; } return 0; } -#ifdef CONFIG_MTD_NAND_VERIFY_WRITE /** - * nand_verify_pages - [GENERIC] verify the chip contents after a write - * @mtd: MTD device structure - * @this: NAND chip structure - * @page: startpage inside the chip, must be called with (page & this->pagemask) - * @numpages: number of pages to verify - * @oob_buf: out of band data buffer - * @oobsel: out of band selecttion structre - * @chipnr: number of the current chip - * @oobmode: 1 = full buffer verify, 0 = ecc only + * nand_read_page_hwecc - [REPLACABLE] hardware ecc based page read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data * - * The NAND device assumes that it is always writing to a cleanly erased page. - * Hence, it performs its internal write verification only on bits that - * transitioned from 1 to 0. The device does NOT verify the whole page on a - * byte by byte basis. It is possible that the page was not completely erased - * or the page is becoming unusable due to wear. The read with ECC would catch - * the error later when the ECC page check fails, but we would rather catch - * it early in the page write stage. Better to write no data than invalid data. + * Not for syndrome calculating ecc controllers which need a special oob layout */ -static int nand_verify_pages (struct mtd_info *mtd, struct nand_chip *this, int page, int numpages, - u_char *oob_buf, struct nand_oobinfo *oobsel, int chipnr, int oobmode) -{ - int i, j, datidx = 0, oobofs = 0, res = -EIO; - int eccsteps = this->eccsteps; - int hweccbytes; - u_char oobdata[64]; - - hweccbytes = (this->options & NAND_HWECC_SYNDROME) ? (oobsel->eccbytes / eccsteps) : 0; - - /* Send command to read back the first page */ - this->cmdfunc (mtd, NAND_CMD_READ0, 0, page); - - for(;;) { - for (j = 0; j < eccsteps; j++) { - /* Loop through and verify the data */ - if (this->verify_buf(mtd, &this->data_poi[datidx], mtd->eccsize)) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "%s: " - "Failed write verify, page 0x%08x ", - __FUNCTION__, page); - goto out; - } - datidx += mtd->eccsize; - /* Have we a hw generator layout ? */ - if (!hweccbytes) - continue; - if (this->verify_buf(mtd, &this->oob_buf[oobofs], hweccbytes)) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "%s: " - "Failed write verify, page 0x%08x ", - __FUNCTION__, page); - goto out; - } - oobofs += hweccbytes; - } +static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + chip->ecc.hwctl(mtd, NAND_ECC_READ); + chip->read_buf(mtd, p, eccsize); + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + } + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - /* check, if we must compare all data or if we just have to - * compare the ecc bytes - */ - if (oobmode) { - if (this->verify_buf(mtd, &oob_buf[oobofs], mtd->oobsize - hweccbytes * eccsteps)) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "%s: " - "Failed write verify, page 0x%08x ", - __FUNCTION__, page); - goto out; - } - } else { - /* Read always, else autoincrement fails */ - this->read_buf(mtd, oobdata, mtd->oobsize - hweccbytes * eccsteps); - - if (oobsel->useecc != MTD_NANDECC_OFF && !hweccbytes) { - int ecccnt = oobsel->eccbytes; - - for (i = 0; i < ecccnt; i++) { - int idx = oobsel->eccpos[i]; - if (oobdata[idx] != oob_buf[oobofs + idx] ) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "%s: Failed ECC write " - "verify, page 0x%08x, " - "%6i bytes were succesful\n", - __FUNCTION__, page, i); - goto out; - } - } - } - } - oobofs += mtd->oobsize - hweccbytes * eccsteps; - page++; - numpages--; - - /* Apply delay or wait for ready/busy pin - * Do this before the AUTOINCR check, so no problems - * arise if a chip which does auto increment - * is marked as NOAUTOINCR by the board driver. - * Do this also before returning, so the chip is - * ready for the next command. - */ - if (!this->dev_ready) - udelay (this->chip_delay); - else - while (!this->dev_ready(mtd)); + for (i = 0; i < chip->ecc.total; i++) + ecc_code[i] = chip->oob_poi[eccpos[i]]; - /* All done, return happy */ - if (!numpages) - return 0; + eccsteps = chip->ecc.steps; + p = buf; + for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; - /* Check, if the chip supports auto page increment */ - if (!NAND_CANAUTOINCR(this)) - this->cmdfunc (mtd, NAND_CMD_READ0, 0x00, page); + stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); + if (stat == -1) + mtd->ecc_stats.failed++; + else + mtd->ecc_stats.corrected += stat; } - /* - * Terminate the read command. We come here in case of an error - * So we must issue a reset command. - */ -out: - this->cmdfunc (mtd, NAND_CMD_RESET, -1, -1); - return res; + return 0; } -#endif /** - * nand_read - [MTD Interface] MTD compability function for nand_read_ecc - * @mtd: MTD device structure - * @from: offset to read from - * @len: number of bytes to read - * @retlen: pointer to variable to store the number of read bytes - * @buf: the databuffer to put data + * nand_read_page_syndrome - [REPLACABLE] hardware ecc syndrom based page read + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data * - * This function simply calls nand_read_ecc with oob buffer and oobsel = NULL -*/ -static int nand_read (struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, u_char * buf) + * The hw generator calculates the error syndrome automatically. Therefor + * we need a special oob layout and handling. + */ +static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf) { - return nand_read_ecc (mtd, from, len, retlen, buf, NULL, NULL); + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *oob = chip->oob_poi; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; + + chip->ecc.hwctl(mtd, NAND_ECC_READ); + chip->read_buf(mtd, p, eccsize); + + if (chip->ecc.prepad) { + chip->read_buf(mtd, oob, chip->ecc.prepad); + oob += chip->ecc.prepad; + } + + chip->ecc.hwctl(mtd, NAND_ECC_READSYN); + chip->read_buf(mtd, oob, eccbytes); + stat = chip->ecc.correct(mtd, p, oob, NULL); + + if (stat == -1) + mtd->ecc_stats.failed++; + else + mtd->ecc_stats.corrected += stat; + + oob += eccbytes; + + if (chip->ecc.postpad) { + chip->read_buf(mtd, oob, chip->ecc.postpad); + oob += chip->ecc.postpad; + } + } + + /* Calculate remaining oob bytes */ + i = mtd->oobsize - (oob - chip->oob_poi); + if (i) + chip->read_buf(mtd, oob, i); + + return 0; } +/** + * nand_transfer_oob - [Internal] Transfer oob to client buffer + * @chip: nand chip structure + * @oob: oob destination address + * @ops: oob ops structure + * @len: size of oob to transfer + */ +static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob, + struct mtd_oob_ops *ops, size_t len) +{ + switch(ops->mode) { + + case MTD_OOB_PLACE: + case MTD_OOB_RAW: + memcpy(oob, chip->oob_poi + ops->ooboffs, len); + return oob + len; + + case MTD_OOB_AUTO: { + struct nand_oobfree *free = chip->ecc.layout->oobfree; + uint32_t boffs = 0, roffs = ops->ooboffs; + size_t bytes = 0; + + for(; free->length && len; free++, len -= bytes) { + /* Read request not from offset 0 ? */ + if (unlikely(roffs)) { + if (roffs >= free->length) { + roffs -= free->length; + continue; + } + boffs = free->offset + roffs; + bytes = min_t(size_t, len, + (free->length - roffs)); + roffs = 0; + } else { + bytes = min_t(size_t, len, free->length); + boffs = free->offset; + } + memcpy(oob, chip->oob_poi + boffs, bytes); + oob += bytes; + } + return oob; + } + default: + BUG(); + } + return NULL; +} /** - * nand_read_ecc - [MTD Interface] Read data with ECC + * nand_do_read_ops - [Internal] Read data with ECC + * * @mtd: MTD device structure * @from: offset to read from - * @len: number of bytes to read - * @retlen: pointer to variable to store the number of read bytes - * @buf: the databuffer to put data - * @oob_buf: filesystem supplied oob data buffer - * @oobsel: oob selection structure + * @ops: oob ops structure * - * NAND read with ECC + * Internal function. Called with chip held. */ -static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, - size_t * retlen, u_char * buf, u_char * oob_buf, struct nand_oobinfo *oobsel) +static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) { - int i, j, col, realpage, page, end, ecc, chipnr, sndcmd = 1; - int read = 0, oob = 0, ecc_status = 0, ecc_failed = 0; - struct nand_chip *this = mtd->priv; - u_char *data_poi, *oob_data = oob_buf; - u_char ecc_calc[NAND_MAX_OOBSIZE]; - u_char ecc_code[NAND_MAX_OOBSIZE]; - int eccmode, eccsteps; - unsigned *oob_config; - int datidx; - int blockcheck = (1 << (this->phys_erase_shift - this->page_shift)) - 1; - int eccbytes; - int compareecc = 1; - int oobreadlen; + int chipnr, page, realpage, col, bytes, aligned; + struct nand_chip *chip = mtd->priv; + struct mtd_ecc_stats stats; + int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; + int sndcmd = 1; + int ret = 0; + uint32_t readlen = ops->len; + uint32_t oobreadlen = ops->ooblen; + uint8_t *bufpoi, *oob, *buf; + stats = mtd->ecc_stats; - MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_read_ecc: from = 0x%08x, len = %i\n", - (unsigned int) from, (int) len); + chipnr = (int)(from >> chip->chip_shift); + chip->select_chip(mtd, chipnr); - /* Do not allow reads past end of device */ - if ((from + len) > mtd->size) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_read_ecc: Attempt read beyond end of device\n"); - *retlen = 0; - return -EINVAL; - } + realpage = (int)(from >> chip->page_shift); + page = realpage & chip->pagemask; - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd ,FL_READING); + col = (int)(from & (mtd->writesize - 1)); - /* use userspace supplied oobinfo, if zero */ - if (oobsel == NULL) - oobsel = &mtd->oobinfo; + buf = ops->datbuf; + oob = ops->oobbuf; - /* Autoplace of oob data ? Use the default placement scheme */ - if (oobsel->useecc == MTD_NANDECC_AUTOPLACE) - oobsel = this->autooob; + while(1) { + bytes = min(mtd->writesize - col, readlen); + aligned = (bytes == mtd->writesize); - eccmode = oobsel->useecc ? this->eccmode : NAND_ECC_NONE; - oob_config = oobsel->eccpos; + /* Is the current page in the buffer ? */ + if (realpage != chip->pagebuf || oob) { + bufpoi = aligned ? buf : chip->buffers->databuf; - /* Select the NAND device */ - chipnr = (int)(from >> this->chip_shift); - this->select_chip(mtd, chipnr); + if (likely(sndcmd)) { + chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + sndcmd = 0; + } - /* First we calculate the starting page */ - realpage = (int) (from >> this->page_shift); - page = realpage & this->pagemask; + /* Now read the page into the buffer */ + if (unlikely(ops->mode == MTD_OOB_RAW)) + ret = chip->ecc.read_page_raw(mtd, chip, bufpoi); + else + ret = chip->ecc.read_page(mtd, chip, bufpoi); + if (ret < 0) + break; - /* Get raw starting column */ - col = from & (mtd->oobblock - 1); + /* Transfer not aligned data */ + if (!aligned) { + chip->pagebuf = realpage; + memcpy(buf, chip->buffers->databuf + col, bytes); + } - end = mtd->oobblock; - ecc = this->eccsize; - eccbytes = this->eccbytes; + buf += bytes; + + if (unlikely(oob)) { + /* Raw mode does data:oob:data:oob */ + if (ops->mode != MTD_OOB_RAW) { + int toread = min(oobreadlen, + chip->ecc.layout->oobavail); + if (toread) { + oob = nand_transfer_oob(chip, + oob, ops, toread); + oobreadlen -= toread; + } + } else + buf = nand_transfer_oob(chip, + buf, ops, mtd->oobsize); + } - if ((eccmode == NAND_ECC_NONE) || (this->options & NAND_HWECC_SYNDROME)) - compareecc = 0; + if (!(chip->options & NAND_NO_READRDY)) { + /* + * Apply delay or wait for ready/busy pin. Do + * this before the AUTOINCR check, so no + * problems arise if a chip which does auto + * increment is marked as NOAUTOINCR by the + * board driver. + */ + if (!chip->dev_ready) + udelay(chip->chip_delay); + else + nand_wait_ready(mtd); + } + } else { + memcpy(buf, chip->buffers->databuf + col, bytes); + buf += bytes; + } - oobreadlen = mtd->oobsize; - if (this->options & NAND_HWECC_SYNDROME) - oobreadlen -= oobsel->eccbytes; + readlen -= bytes; - /* Loop until all data read */ - while (read < len) { + if (!readlen) + break; - int aligned = (!col && (len - read) >= end); - /* - * If the read is not page aligned, we have to read into data buffer - * due to ecc, else we read into return buffer direct - */ - if (aligned) - data_poi = &buf[read]; - else - data_poi = this->data_buf; + /* For subsequent reads align to page boundary. */ + col = 0; + /* Increment page address */ + realpage++; - /* Check, if we have this page in the buffer - * - * FIXME: Make it work when we must provide oob data too, - * check the usage of data_buf oob field - */ - if (realpage == this->pagebuf && !oob_buf) { - /* aligned read ? */ - if (aligned) - memcpy (data_poi, this->data_buf, end); - goto readdata; + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); } - /* Check, if we must send the read command */ - if (sndcmd) { - this->cmdfunc (mtd, NAND_CMD_READ0, 0x00, page); - sndcmd = 0; - } + /* Check, if the chip supports auto page increment + * or if we have hit a block boundary. + */ + if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck)) + sndcmd = 1; + } - /* get oob area, if we have no oob buffer from fs-driver */ - if (!oob_buf || oobsel->useecc == MTD_NANDECC_AUTOPLACE || - oobsel->useecc == MTD_NANDECC_AUTOPL_USR) - oob_data = &this->data_buf[end]; + ops->retlen = ops->len - (size_t) readlen; + if (oob) + ops->oobretlen = ops->ooblen - oobreadlen; - eccsteps = this->eccsteps; + if (ret) + return ret; - switch (eccmode) { - case NAND_ECC_NONE: { /* No ECC, Read in a page */ -/* XXX U-BOOT XXX */ -#if 0 - static unsigned long lastwhinge = 0; - if ((lastwhinge / HZ) != (jiffies / HZ)) { - printk (KERN_WARNING "Reading data from NAND FLASH without ECC is not recommended\n"); - lastwhinge = jiffies; - } -#else - puts("Reading data from NAND FLASH without ECC is not recommended\n"); -#endif - this->read_buf(mtd, data_poi, end); - break; - } + if (mtd->ecc_stats.failed - stats.failed) + return -EBADMSG; - case NAND_ECC_SOFT: /* Software ECC 3/256: Read in a page + oob data */ - this->read_buf(mtd, data_poi, end); - for (i = 0, datidx = 0; eccsteps; eccsteps--, i+=3, datidx += ecc) - this->calculate_ecc(mtd, &data_poi[datidx], &ecc_calc[i]); - break; + return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0; +} - default: - for (i = 0, datidx = 0; eccsteps; eccsteps--, i+=eccbytes, datidx += ecc) { - this->enable_hwecc(mtd, NAND_ECC_READ); - this->read_buf(mtd, &data_poi[datidx], ecc); - - /* HW ecc with syndrome calculation must read the - * syndrome from flash immidiately after the data */ - if (!compareecc) { - /* Some hw ecc generators need to know when the - * syndrome is read from flash */ - this->enable_hwecc(mtd, NAND_ECC_READSYN); - this->read_buf(mtd, &oob_data[i], eccbytes); - /* We calc error correction directly, it checks the hw - * generator for an error, reads back the syndrome and - * does the error correction on the fly */ - if (this->correct_data(mtd, &data_poi[datidx], &oob_data[i], &ecc_code[i]) == -1) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_ecc: " - "Failed ECC read, page 0x%08x on chip %d\n", page, chipnr); - ecc_failed++; - } - } else { - this->calculate_ecc(mtd, &data_poi[datidx], &ecc_calc[i]); - } - } - break; - } +/** + * nand_read - [MTD Interface] MTD compability function for nand_do_read_ecc + * @mtd: MTD device structure + * @from: offset to read from + * @len: number of bytes to read + * @retlen: pointer to variable to store the number of read bytes + * @buf: the databuffer to put data + * + * Get hold of the chip and call nand_do_read + */ +static int nand_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, uint8_t *buf) +{ + struct nand_chip *chip = mtd->priv; + int ret; - /* read oobdata */ - this->read_buf(mtd, &oob_data[mtd->oobsize - oobreadlen], oobreadlen); + /* Do not allow reads past end of device */ + if ((from + len) > mtd->size) + return -EINVAL; + if (!len) + return 0; - /* Skip ECC check, if not requested (ECC_NONE or HW_ECC with syndromes) */ - if (!compareecc) - goto readoob; + nand_get_device(chip, mtd, FL_READING); - /* Pick the ECC bytes out of the oob data */ - for (j = 0; j < oobsel->eccbytes; j++) - ecc_code[j] = oob_data[oob_config[j]]; + chip->ops.len = len; + chip->ops.datbuf = buf; + chip->ops.oobbuf = NULL; - /* correct data, if neccecary */ - for (i = 0, j = 0, datidx = 0; i < this->eccsteps; i++, datidx += ecc) { - ecc_status = this->correct_data(mtd, &data_poi[datidx], &ecc_code[j], &ecc_calc[j]); + ret = nand_do_read_ops(mtd, from, &chip->ops); - /* Get next chunk of ecc bytes */ - j += eccbytes; + *retlen = chip->ops.retlen; - /* Check, if we have a fs supplied oob-buffer, - * This is the legacy mode. Used by YAFFS1 - * Should go away some day - */ - if (oob_buf && oobsel->useecc == MTD_NANDECC_PLACE) { - int *p = (int *)(&oob_data[mtd->oobsize]); - p[i] = ecc_status; - } + nand_release_device(mtd); - if (ecc_status == -1) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_ecc: " - "Failed ECC read, page 0x%08x\n", - page); - ecc_failed++; - } - } + return ret; +} - readoob: - /* check, if we have a fs supplied oob-buffer */ - if (oob_buf) { - /* without autoplace. Legacy mode used by YAFFS1 */ - switch(oobsel->useecc) { - case MTD_NANDECC_AUTOPLACE: - case MTD_NANDECC_AUTOPL_USR: - /* Walk through the autoplace chunks */ - for (i = 0, j = 0; j < mtd->oobavail; i++) { - int from = oobsel->oobfree[i][0]; - int num = oobsel->oobfree[i][1]; - memcpy(&oob_buf[oob+j], &oob_data[from], num); - j+= num; - } - oob += mtd->oobavail; - break; - case MTD_NANDECC_PLACE: - /* YAFFS1 legacy mode */ - oob_data += this->eccsteps * sizeof (int); - default: - oob_data += mtd->oobsize; - } - } - readdata: - /* Partial page read, transfer data into fs buffer */ - if (!aligned) { - for (j = col; j < end && read < len; j++) - buf[read++] = data_poi[j]; - this->pagebuf = realpage; +/** + * nand_read_oob_std - [REPLACABLE] the most common OOB data read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to read + * @sndcmd: flag whether to issue read command or not + */ +static int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip, + int page, int sndcmd) +{ + if (sndcmd) { + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + sndcmd = 0; + } + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return sndcmd; +} + +/** + * nand_read_oob_syndrome - [REPLACABLE] OOB data read function for HW ECC + * with syndromes + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to read + * @sndcmd: flag whether to issue read command or not + */ +static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, + int page, int sndcmd) +{ + uint8_t *buf = chip->oob_poi; + int length = mtd->oobsize; + int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; + int eccsize = chip->ecc.size; + uint8_t *bufpoi = buf; + int i, toread, sndrnd = 0, pos; + + chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page); + for (i = 0; i < chip->ecc.steps; i++) { + if (sndrnd) { + pos = eccsize + i * (eccsize + chunk); + if (mtd->writesize > 512) + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, pos, -1); + else + chip->cmdfunc(mtd, NAND_CMD_READ0, pos, page); } else - read += mtd->oobblock; - - /* Apply delay or wait for ready/busy pin - * Do this before the AUTOINCR check, so no problems - * arise if a chip which does auto increment - * is marked as NOAUTOINCR by the board driver. - */ - if (!this->dev_ready) - udelay (this->chip_delay); - else - while (!this->dev_ready(mtd)); + sndrnd = 1; + toread = min_t(int, length, chunk); + chip->read_buf(mtd, bufpoi, toread); + bufpoi += toread; + length -= toread; + } + if (length > 0) + chip->read_buf(mtd, bufpoi, length); - if (read == len) - break; + return 1; +} - /* For subsequent reads align to page boundary. */ - col = 0; - /* Increment page address */ - realpage++; +/** + * nand_write_oob_std - [REPLACABLE] the most common OOB data write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to write + */ +static int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + int status = 0; + const uint8_t *buf = chip->oob_poi; + int length = mtd->oobsize; - page = realpage & this->pagemask; - /* Check, if we cross a chip boundary */ - if (!page) { - chipnr++; - this->select_chip(mtd, -1); - this->select_chip(mtd, chipnr); - } - /* Check, if the chip supports auto page increment - * or if we have hit a block boundary. - */ - if (!NAND_CANAUTOINCR(this) || !(page & blockcheck)) - sndcmd = 1; - } + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); + chip->write_buf(mtd, buf, length); + /* Send command to program the OOB data */ + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - /* Deselect and wake up anyone waiting on the device */ - nand_release_device(mtd); + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/** + * nand_write_oob_syndrome - [REPLACABLE] OOB data write function for HW ECC + * with syndrome - only for large page flash ! + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to write + */ +static int nand_write_oob_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; + int eccsize = chip->ecc.size, length = mtd->oobsize; + int i, len, pos, status = 0, sndcmd = 0, steps = chip->ecc.steps; + const uint8_t *bufpoi = chip->oob_poi; /* - * Return success, if no ECC failures, else -EBADMSG - * fs driver will take care of that, because - * retlen == desired len and result == -EBADMSG + * data-ecc-data-ecc ... ecc-oob + * or + * data-pad-ecc-pad-data-pad .... ecc-pad-oob */ - *retlen = read; - return ecc_failed ? -EBADMSG : 0; + if (!chip->ecc.prepad && !chip->ecc.postpad) { + pos = steps * (eccsize + chunk); + steps = 0; + } else + pos = eccsize; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page); + for (i = 0; i < steps; i++) { + if (sndcmd) { + if (mtd->writesize <= 512) { + uint32_t fill = 0xFFFFFFFF; + + len = eccsize; + while (len > 0) { + int num = min_t(int, len, 4); + chip->write_buf(mtd, (uint8_t *)&fill, + num); + len -= num; + } + } else { + pos = eccsize + i * (eccsize + chunk); + chip->cmdfunc(mtd, NAND_CMD_RNDIN, pos, -1); + } + } else + sndcmd = 1; + len = min_t(int, length, chunk); + chip->write_buf(mtd, bufpoi, len); + bufpoi += len; + length -= len; + } + if (length > 0) + chip->write_buf(mtd, bufpoi, length); + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; } /** - * nand_read_oob - [MTD Interface] NAND read out-of-band + * nand_do_read_oob - [Intern] NAND read out-of-band * @mtd: MTD device structure * @from: offset to read from - * @len: number of bytes to read - * @retlen: pointer to variable to store the number of read bytes - * @buf: the databuffer to put data + * @ops: oob operations description structure * * NAND read out-of-band data from the spare area */ -static int nand_read_oob (struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, u_char * buf) +static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) { - int i, col, page, chipnr; - struct nand_chip *this = mtd->priv; - int blockcheck = (1 << (this->phys_erase_shift - this->page_shift)) - 1; - - MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_read_oob: from = 0x%08x, len = %i\n", - (unsigned int) from, (int) len); - - /* Shift to get page */ - page = (int)(from >> this->page_shift); - chipnr = (int)(from >> this->chip_shift); - - /* Mask to get column */ - col = from & (mtd->oobsize - 1); + int page, realpage, chipnr, sndcmd = 1; + struct nand_chip *chip = mtd->priv; + int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; + int readlen = ops->ooblen; + int len; + uint8_t *buf = ops->oobbuf; + + MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_read_oob: from = 0x%08Lx, len = %i\n", + (unsigned long long)from, readlen); + + if (ops->mode == MTD_OOB_AUTO) + len = chip->ecc.layout->oobavail; + else + len = mtd->oobsize; - /* Initialize return length value */ - *retlen = 0; + if (unlikely(ops->ooboffs >= len)) { + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: " + "Attempt to start read outside oob\n"); + return -EINVAL; + } /* Do not allow reads past end of device */ - if ((from + len) > mtd->size) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_read_oob: Attempt read beyond end of device\n"); - *retlen = 0; + if (unlikely(from >= mtd->size || + ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) - + (from >> chip->page_shift)) * len)) { + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: " + "Attempt read beyond end of device\n"); return -EINVAL; } - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd , FL_READING); + chipnr = (int)(from >> chip->chip_shift); + chip->select_chip(mtd, chipnr); - /* Select the NAND device */ - this->select_chip(mtd, chipnr); + /* Shift to get page */ + realpage = (int)(from >> chip->page_shift); + page = realpage & chip->pagemask; - /* Send the read command */ - this->cmdfunc (mtd, NAND_CMD_READOOB, col, page & this->pagemask); - /* - * Read the data, if we read more than one page - * oob data, let the device transfer the data ! - */ - i = 0; - while (i < len) { - int thislen = mtd->oobsize - col; - thislen = min_t(int, thislen, len); - this->read_buf(mtd, &buf[i], thislen); - i += thislen; - - /* Apply delay or wait for ready/busy pin - * Do this before the AUTOINCR check, so no problems - * arise if a chip which does auto increment - * is marked as NOAUTOINCR by the board driver. - */ - if (!this->dev_ready) - udelay (this->chip_delay); - else - while (!this->dev_ready(mtd)); - - /* Read more ? */ - if (i < len) { - page++; - col = 0; - - /* Check, if we cross a chip boundary */ - if (!(page & this->pagemask)) { - chipnr++; - this->select_chip(mtd, -1); - this->select_chip(mtd, chipnr); - } + while(1) { + sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd); - /* Check, if the chip supports auto page increment - * or if we have hit a block boundary. - */ - if (!NAND_CANAUTOINCR(this) || !(page & blockcheck)) { - /* For subsequent page reads set offset to 0 */ - this->cmdfunc (mtd, NAND_CMD_READOOB, 0x0, page & this->pagemask); - } + len = min(len, readlen); + buf = nand_transfer_oob(chip, buf, ops, len); + + if (!(chip->options & NAND_NO_READRDY)) { + /* + * Apply delay or wait for ready/busy pin. Do this + * before the AUTOINCR check, so no problems arise if a + * chip which does auto increment is marked as + * NOAUTOINCR by the board driver. + */ + if (!chip->dev_ready) + udelay(chip->chip_delay); + else + nand_wait_ready(mtd); } - } - /* Deselect and wake up anyone waiting on the device */ - nand_release_device(mtd); + readlen -= len; + if (!readlen) + break; + + /* Increment page address */ + realpage++; + + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + } + + /* Check, if the chip supports auto page increment + * or if we have hit a block boundary. + */ + if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck)) + sndcmd = 1; + } - /* Return happy */ - *retlen = len; + ops->oobretlen = ops->ooblen; return 0; } /** - * nand_read_raw - [GENERIC] Read raw data including oob into buffer + * nand_read_oob - [MTD Interface] NAND read data and/or out-of-band * @mtd: MTD device structure - * @buf: temporary buffer * @from: offset to read from - * @len: number of bytes to read - * @ooblen: number of oob data bytes to read + * @ops: oob operation description structure * - * Read raw data including oob into buffer + * NAND read data and/or out-of-band data */ -int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_t len, size_t ooblen) +static int nand_read_oob(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) { - struct nand_chip *this = mtd->priv; - int page = (int) (from >> this->page_shift); - int chip = (int) (from >> this->chip_shift); - int sndcmd = 1; - int cnt = 0; - int pagesize = mtd->oobblock + mtd->oobsize; - int blockcheck = (1 << (this->phys_erase_shift - this->page_shift)) - 1; + struct nand_chip *chip = mtd->priv; + int ret = -ENOTSUPP; + + ops->retlen = 0; /* Do not allow reads past end of device */ - if ((from + len) > mtd->size) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_read_raw: Attempt read beyond end of device\n"); + if (ops->datbuf && (from + ops->len) > mtd->size) { + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: " + "Attempt read beyond end of device\n"); return -EINVAL; } - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd , FL_READING); + nand_get_device(chip, mtd, FL_READING); - this->select_chip (mtd, chip); + switch(ops->mode) { + case MTD_OOB_PLACE: + case MTD_OOB_AUTO: + case MTD_OOB_RAW: + break; - /* Add requested oob length */ - len += ooblen; + default: + goto out; + } - while (len) { - if (sndcmd) - this->cmdfunc (mtd, NAND_CMD_READ0, 0, page & this->pagemask); - sndcmd = 0; + if (!ops->datbuf) + ret = nand_do_read_oob(mtd, from, ops); + else + ret = nand_do_read_ops(mtd, from, ops); - this->read_buf (mtd, &buf[cnt], pagesize); + out: + nand_release_device(mtd); + return ret; +} - len -= pagesize; - cnt += pagesize; - page++; - if (!this->dev_ready) - udelay (this->chip_delay); - else - while (!this->dev_ready(mtd)); +/** + * nand_write_page_raw - [Intern] raw page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + */ +static void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf) +{ + chip->write_buf(mtd, buf, mtd->writesize); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); +} - /* Check, if the chip supports auto page increment */ - if (!NAND_CANAUTOINCR(this) || !(page & blockcheck)) - sndcmd = 1; - } +/** + * nand_write_page_swecc - [REPLACABLE] software ecc based page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + */ +static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *ecc_calc = chip->buffers->ecccalc; + const uint8_t *p = buf; + uint32_t *eccpos = chip->ecc.layout->eccpos; - /* Deselect and wake up anyone waiting on the device */ - nand_release_device(mtd); - return 0; + /* Software ecc calculation */ + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; + + chip->ecc.write_page_raw(mtd, chip, buf); } +/** + * nand_write_page_hwecc - [REPLACABLE] hardware ecc based page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + */ +static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *ecc_calc = chip->buffers->ecccalc; + const uint8_t *p = buf; + uint32_t *eccpos = chip->ecc.layout->eccpos; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); + chip->write_buf(mtd, p, eccsize); + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + } + + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; + + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); +} /** - * nand_prepare_oobbuf - [GENERIC] Prepare the out of band buffer - * @mtd: MTD device structure - * @fsbuf: buffer given by fs driver - * @oobsel: out of band selection structre - * @autoplace: 1 = place given buffer into the oob bytes - * @numpages: number of pages to prepare - * - * Return: - * 1. Filesystem buffer available and autoplacement is off, - * return filesystem buffer - * 2. No filesystem buffer or autoplace is off, return internal - * buffer - * 3. Filesystem buffer is given and autoplace selected - * put data from fs buffer into internal buffer and - * retrun internal buffer - * - * Note: The internal buffer is filled with 0xff. This must - * be done only once, when no autoplacement happens - * Autoplacement sets the buffer dirty flag, which - * forces the 0xff fill before using the buffer again. + * nand_write_page_syndrome - [REPLACABLE] hardware ecc syndrom based page write + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer * -*/ -static u_char * nand_prepare_oobbuf (struct mtd_info *mtd, u_char *fsbuf, struct nand_oobinfo *oobsel, - int autoplace, int numpages) + * The hw generator calculates the error syndrome automatically. Therefor + * we need a special oob layout and handling. + */ +static void nand_write_page_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf) { - struct nand_chip *this = mtd->priv; - int i, len, ofs; + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + const uint8_t *p = buf; + uint8_t *oob = chip->oob_poi; - /* Zero copy fs supplied buffer */ - if (fsbuf && !autoplace) - return fsbuf; + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { - /* Check, if the buffer must be filled with ff again */ - if (this->oobdirty) { - memset (this->oob_buf, 0xff, - mtd->oobsize << (this->phys_erase_shift - this->page_shift)); - this->oobdirty = 0; - } + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); + chip->write_buf(mtd, p, eccsize); - /* If we have no autoplacement or no fs buffer use the internal one */ - if (!autoplace || !fsbuf) - return this->oob_buf; - - /* Walk through the pages and place the data */ - this->oobdirty = 1; - ofs = 0; - while (numpages--) { - for (i = 0, len = 0; len < mtd->oobavail; i++) { - int to = ofs + oobsel->oobfree[i][0]; - int num = oobsel->oobfree[i][1]; - memcpy (&this->oob_buf[to], fsbuf, num); - len += num; - fsbuf += num; + if (chip->ecc.prepad) { + chip->write_buf(mtd, oob, chip->ecc.prepad); + oob += chip->ecc.prepad; + } + + chip->ecc.calculate(mtd, p, oob); + chip->write_buf(mtd, oob, eccbytes); + oob += eccbytes; + + if (chip->ecc.postpad) { + chip->write_buf(mtd, oob, chip->ecc.postpad); + oob += chip->ecc.postpad; } - ofs += mtd->oobavail; } - return this->oob_buf; -} -#define NOTALIGNED(x) (x & (mtd->oobblock-1)) != 0 + /* Calculate remaining oob bytes */ + i = mtd->oobsize - (oob - chip->oob_poi); + if (i) + chip->write_buf(mtd, oob, i); +} /** - * nand_write - [MTD Interface] compability function for nand_write_ecc + * nand_write_page - [REPLACEABLE] write one page * @mtd: MTD device structure - * @to: offset to write to - * @len: number of bytes to write - * @retlen: pointer to variable to store the number of written bytes + * @chip: NAND chip descriptor * @buf: the data to write - * - * This function simply calls nand_write_ecc with oob buffer and oobsel = NULL - * -*/ -static int nand_write (struct mtd_info *mtd, loff_t to, size_t len, size_t * retlen, const u_char * buf) + * @page: page number to write + * @cached: cached programming + * @raw: use _raw version of write_page + */ +static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int page, int cached, int raw) { - return (nand_write_ecc (mtd, to, len, retlen, buf, NULL, NULL)); + int status; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); + + if (unlikely(raw)) + chip->ecc.write_page_raw(mtd, chip, buf); + else + chip->ecc.write_page(mtd, chip, buf); + + /* + * Cached progamming disabled for now, Not sure if its worth the + * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s) + */ + cached = 0; + + if (!cached || !(chip->options & NAND_CACHEPRG)) { + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + /* + * See if operation failed and additional status checks are + * available + */ + if ((status & NAND_STATUS_FAIL) && (chip->errstat)) + status = chip->errstat(mtd, chip, FL_WRITING, status, + page); + + if (status & NAND_STATUS_FAIL) + return -EIO; + } else { + chip->cmdfunc(mtd, NAND_CMD_CACHEDPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + } + +#ifdef CONFIG_MTD_NAND_VERIFY_WRITE + /* Send command to read back the data */ + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + if (chip->verify_buf(mtd, buf, mtd->writesize)) + return -EIO; +#endif + return 0; +} + +/** + * nand_fill_oob - [Internal] Transfer client buffer to oob + * @chip: nand chip structure + * @oob: oob data buffer + * @ops: oob ops structure + */ +static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, + struct mtd_oob_ops *ops) +{ + size_t len = ops->ooblen; + + switch(ops->mode) { + + case MTD_OOB_PLACE: + case MTD_OOB_RAW: + memcpy(chip->oob_poi + ops->ooboffs, oob, len); + return oob + len; + + case MTD_OOB_AUTO: { + struct nand_oobfree *free = chip->ecc.layout->oobfree; + uint32_t boffs = 0, woffs = ops->ooboffs; + size_t bytes = 0; + + for(; free->length && len; free++, len -= bytes) { + /* Write request not from offset 0 ? */ + if (unlikely(woffs)) { + if (woffs >= free->length) { + woffs -= free->length; + continue; + } + boffs = free->offset + woffs; + bytes = min_t(size_t, len, + (free->length - woffs)); + woffs = 0; + } else { + bytes = min_t(size_t, len, free->length); + boffs = free->offset; + } + memcpy(chip->oob_poi + boffs, oob, bytes); + oob += bytes; + } + return oob; + } + default: + BUG(); + } + return NULL; } +#define NOTALIGNED(x) (x & (chip->subpagesize - 1)) != 0 + /** - * nand_write_ecc - [MTD Interface] NAND write with ECC + * nand_do_write_ops - [Internal] NAND write with ECC * @mtd: MTD device structure * @to: offset to write to - * @len: number of bytes to write - * @retlen: pointer to variable to store the number of written bytes - * @buf: the data to write - * @eccbuf: filesystem supplied oob data buffer - * @oobsel: oob selection structure + * @ops: oob operations description structure * * NAND write with ECC */ -static int nand_write_ecc (struct mtd_info *mtd, loff_t to, size_t len, - size_t * retlen, const u_char * buf, u_char * eccbuf, struct nand_oobinfo *oobsel) +static int nand_do_write_ops(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) { - int startpage, page, ret = -EIO, oob = 0, written = 0, chipnr; - int autoplace = 0, numpages, totalpages; - struct nand_chip *this = mtd->priv; - u_char *oobbuf, *bufstart; - int ppblock = (1 << (this->phys_erase_shift - this->page_shift)); - - MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_write_ecc: to = 0x%08x, len = %i\n", - (unsigned int) to, (int) len); - - /* Initialize retlen, in case of early exit */ - *retlen = 0; + int chipnr, realpage, page, blockmask, column; + struct nand_chip *chip = mtd->priv; + uint32_t writelen = ops->len; + uint8_t *oob = ops->oobbuf; + uint8_t *buf = ops->datbuf; + int ret, subpage; - /* Do not allow write past end of device */ - if ((to + len) > mtd->size) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_write_ecc: Attempt to write past end of page\n"); - return -EINVAL; - } + ops->retlen = 0; + if (!writelen) + return 0; /* reject writes, which are not page aligned */ - if (NOTALIGNED (to) || NOTALIGNED(len)) { - printk (KERN_NOTICE "nand_write_ecc: Attempt to write not page aligned data\n"); + if (NOTALIGNED(to) || NOTALIGNED(ops->len)) { + printk(KERN_NOTICE "nand_write: " + "Attempt to write not page aligned data\n"); return -EINVAL; } - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd, FL_WRITING); + column = to & (mtd->writesize - 1); + subpage = column || (writelen & (mtd->writesize - 1)); - /* Calculate chipnr */ - chipnr = (int)(to >> this->chip_shift); - /* Select the NAND device */ - this->select_chip(mtd, chipnr); + if (subpage && oob) + return -EINVAL; + + chipnr = (int)(to >> chip->chip_shift); + chip->select_chip(mtd, chipnr); /* Check, if it is write protected */ if (nand_check_wp(mtd)) { - printk (KERN_NOTICE "nand_write_ecc: Device is write protected\n"); - goto out; + printk (KERN_NOTICE "nand_do_write_ops: Device is write protected\n"); + return -EIO; } - /* if oobsel is NULL, use chip defaults */ - if (oobsel == NULL) - oobsel = &mtd->oobinfo; + realpage = (int)(to >> chip->page_shift); + page = realpage & chip->pagemask; + blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; + + /* Invalidate the page cache, when we write to the cached page */ + if (to <= (chip->pagebuf << chip->page_shift) && + (chip->pagebuf << chip->page_shift) < (to + ops->len)) + chip->pagebuf = -1; + + /* If we're not given explicit OOB data, let it be 0xFF */ + if (likely(!oob)) + memset(chip->oob_poi, 0xff, mtd->oobsize); + + while(1) { + int bytes = mtd->writesize; + int cached = writelen > bytes && page != blockmask; + uint8_t *wbuf = buf; + + /* Partial page write ? */ + if (unlikely(column || writelen < (mtd->writesize - 1))) { + cached = 0; + bytes = min_t(int, bytes - column, (int) writelen); + chip->pagebuf = -1; + memset(chip->buffers->databuf, 0xff, mtd->writesize); + memcpy(&chip->buffers->databuf[column], buf, bytes); + wbuf = chip->buffers->databuf; + } - /* Autoplace of oob data ? Use the default placement scheme */ - if (oobsel->useecc == MTD_NANDECC_AUTOPLACE) { - oobsel = this->autooob; - autoplace = 1; - } - if (oobsel->useecc == MTD_NANDECC_AUTOPL_USR) - autoplace = 1; + if (unlikely(oob)) + oob = nand_fill_oob(chip, oob, ops); - /* Setup variables and oob buffer */ - totalpages = len >> this->page_shift; - page = (int) (to >> this->page_shift); - /* Invalidate the page cache, if we write to the cached page */ - if (page <= this->pagebuf && this->pagebuf < (page + totalpages)) - this->pagebuf = -1; - - /* Set it relative to chip */ - page &= this->pagemask; - startpage = page; - /* Calc number of pages we can write in one go */ - numpages = min (ppblock - (startpage & (ppblock - 1)), totalpages); - oobbuf = nand_prepare_oobbuf (mtd, eccbuf, oobsel, autoplace, numpages); - bufstart = (u_char *)buf; - - /* Loop until all data is written */ - while (written < len) { - - this->data_poi = (u_char*) &buf[written]; - /* Write one page. If this is the last page to write - * or the last page in this block, then use the - * real pageprogram command, else select cached programming - * if supported by the chip. - */ - ret = nand_write_page (mtd, this, page, &oobbuf[oob], oobsel, (--numpages > 0)); - if (ret) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_write_ecc: write_page failed %d\n", ret); - goto out; - } - /* Next oob page */ - oob += mtd->oobsize; - /* Update written bytes count */ - written += mtd->oobblock; - if (written == len) - goto cmp; + ret = chip->write_page(mtd, chip, wbuf, page, cached, + (ops->mode == MTD_OOB_RAW)); + if (ret) + break; - /* Increment page address */ - page++; - - /* Have we hit a block boundary ? Then we have to verify and - * if verify is ok, we have to setup the oob buffer for - * the next pages. - */ - if (!(page & (ppblock - 1))){ - int ofs; - this->data_poi = bufstart; - ret = nand_verify_pages (mtd, this, startpage, - page - startpage, - oobbuf, oobsel, chipnr, (eccbuf != NULL)); - if (ret) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_write_ecc: " - "verify_pages failed %d\n", ret); - goto out; - } - *retlen = written; - bufstart = (u_char*) &buf[written]; - - ofs = autoplace ? mtd->oobavail : mtd->oobsize; - if (eccbuf) - eccbuf += (page - startpage) * ofs; - totalpages -= page - startpage; - numpages = min (totalpages, ppblock); - page &= this->pagemask; - startpage = page; - oob = 0; - this->oobdirty = 1; - oobbuf = nand_prepare_oobbuf (mtd, eccbuf, oobsel, - autoplace, numpages); - /* Check, if we cross a chip boundary */ - if (!page) { - chipnr++; - this->select_chip(mtd, -1); - this->select_chip(mtd, chipnr); - } + writelen -= bytes; + if (!writelen) + break; + + column = 0; + buf += bytes; + realpage++; + + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); } } - /* Verify the remaining pages */ -cmp: - this->data_poi = bufstart; - ret = nand_verify_pages (mtd, this, startpage, totalpages, - oobbuf, oobsel, chipnr, (eccbuf != NULL)); - if (!ret) - *retlen = written; - else - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_write_ecc: verify_pages failed %d\n", ret); - -out: - /* Deselect and wake up anyone waiting on the device */ - nand_release_device(mtd); + ops->retlen = ops->len - writelen; + if (unlikely(oob)) + ops->oobretlen = ops->ooblen; return ret; } - /** - * nand_write_oob - [MTD Interface] NAND write out-of-band + * nand_write - [MTD Interface] NAND write with ECC * @mtd: MTD device structure * @to: offset to write to * @len: number of bytes to write * @retlen: pointer to variable to store the number of written bytes * @buf: the data to write * - * NAND write out-of-band + * NAND write with ECC */ -static int nand_write_oob (struct mtd_info *mtd, loff_t to, size_t len, size_t * retlen, const u_char * buf) +static int nand_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const uint8_t *buf) { - int column, page, status, ret = -EIO, chipnr; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; + int ret; - MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_write_oob: to = 0x%08x, len = %i\n", - (unsigned int) to, (int) len); + /* Do not allow reads past end of device */ + if ((to + len) > mtd->size) + return -EINVAL; + if (!len) + return 0; - /* Shift to get page */ - page = (int) (to >> this->page_shift); - chipnr = (int) (to >> this->chip_shift); + nand_get_device(chip, mtd, FL_WRITING); + + chip->ops.len = len; + chip->ops.datbuf = (uint8_t *)buf; + chip->ops.oobbuf = NULL; - /* Mask to get column */ - column = to & (mtd->oobsize - 1); + ret = nand_do_write_ops(mtd, to, &chip->ops); - /* Initialize return length value */ - *retlen = 0; + *retlen = chip->ops.retlen; + + nand_release_device(mtd); + + return ret; +} + +/** + * nand_do_write_oob - [MTD Interface] NAND write out-of-band + * @mtd: MTD device structure + * @to: offset to write to + * @ops: oob operation description structure + * + * NAND write out-of-band + */ +static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) +{ + int chipnr, page, status, len; + struct nand_chip *chip = mtd->priv; + + MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_write_oob: to = 0x%08x, len = %i\n", + (unsigned int)to, (int)ops->ooblen); + + if (ops->mode == MTD_OOB_AUTO) + len = chip->ecc.layout->oobavail; + else + len = mtd->oobsize; /* Do not allow write past end of page */ - if ((column + len) > mtd->oobsize) { + if ((ops->ooboffs + ops->ooblen) > len) { MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_write_oob: " "Attempt to write past end of page\n"); return -EINVAL; } - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd, FL_WRITING); + if (unlikely(ops->ooboffs >= len)) { + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: " + "Attempt to start write outside oob\n"); + return -EINVAL; + } - /* Select the NAND device */ - this->select_chip(mtd, chipnr); + /* Do not allow reads past end of device */ + if (unlikely(to >= mtd->size || + ops->ooboffs + ops->ooblen > + ((mtd->size >> chip->page_shift) - + (to >> chip->page_shift)) * len)) { + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: " + "Attempt write beyond end of device\n"); + return -EINVAL; + } + + chipnr = (int)(to >> chip->chip_shift); + chip->select_chip(mtd, chipnr); - /* Reset the chip. Some chips (like the Toshiba TC5832DC found - in one of my DiskOnChip 2000 test units) will clear the whole - data page too if we don't do this. I have no clue why, but - I seem to have 'fixed' it in the doc2000 driver in - August 1999. dwmw2. */ - this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + /* Shift to get page */ + page = (int)(to >> chip->page_shift); + + /* + * Reset the chip. Some chips (like the Toshiba TC5832DC found in one + * of my DiskOnChip 2000 test units) will clear the whole data page too + * if we don't do this. I have no clue why, but I seem to have 'fixed' + * it in the doc2000 driver in August 1999. dwmw2. + */ + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); /* Check, if it is write protected */ if (nand_check_wp(mtd)) - goto out; + return -EROFS; /* Invalidate the page cache, if we write to the cached page */ - if (page == this->pagebuf) - this->pagebuf = -1; - - if (NAND_MUST_PAD(this)) { - /* Write out desired data */ - this->cmdfunc (mtd, NAND_CMD_SEQIN, mtd->oobblock, page & this->pagemask); - if (!ffchars) { - if (!(ffchars = kmalloc (mtd->oobsize, GFP_KERNEL))) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_write_oob: " - "No memory for padding array, " - "need %d bytes", mtd->oobsize); - ret = -ENOMEM; - goto out; - } - memset(ffchars, 0xff, mtd->oobsize); - } - /* prepad 0xff for partial programming */ - this->write_buf(mtd, ffchars, column); - /* write data */ - this->write_buf(mtd, buf, len); - /* postpad 0xff for partial programming */ - this->write_buf(mtd, ffchars, mtd->oobsize - (len+column)); - } else { - /* Write out desired data */ - this->cmdfunc (mtd, NAND_CMD_SEQIN, mtd->oobblock + column, page & this->pagemask); - /* write data */ - this->write_buf(mtd, buf, len); - } - /* Send command to program the OOB data */ - this->cmdfunc (mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = this->waitfunc (mtd, this, FL_WRITING); - - /* See if device thinks it succeeded */ - if (status & 0x01) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_write_oob: " - "Failed write, page 0x%08x\n", page); - ret = -EIO; - goto out; - } - /* Return happy */ - *retlen = len; + if (page == chip->pagebuf) + chip->pagebuf = -1; -#ifdef CONFIG_MTD_NAND_VERIFY_WRITE - /* Send command to read back the data */ - this->cmdfunc (mtd, NAND_CMD_READOOB, column, page & this->pagemask); + memset(chip->oob_poi, 0xff, mtd->oobsize); + nand_fill_oob(chip, ops->oobbuf, ops); + status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask); + memset(chip->oob_poi, 0xff, mtd->oobsize); - if (this->verify_buf(mtd, buf, len)) { - MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_write_oob: " - "Failed write verify, page 0x%08x\n", page); - ret = -EIO; - goto out; - } -#endif - ret = 0; -out: - /* Deselect and wake up anyone waiting on the device */ - nand_release_device(mtd); + if (status) + return status; - return ret; -} + ops->oobretlen = ops->ooblen; -/* XXX U-BOOT XXX */ -#if 0 -/** - * nand_writev - [MTD Interface] compabilty function for nand_writev_ecc - * @mtd: MTD device structure - * @vecs: the iovectors to write - * @count: number of vectors - * @to: offset to write to - * @retlen: pointer to variable to store the number of written bytes - * - * NAND write with kvec. This just calls the ecc function - */ -static int nand_writev (struct mtd_info *mtd, const struct kvec *vecs, unsigned long count, - loff_t to, size_t * retlen) -{ - return (nand_writev_ecc (mtd, vecs, count, to, retlen, NULL, NULL)); + return 0; } /** - * nand_writev_ecc - [MTD Interface] write with iovec with ecc + * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band * @mtd: MTD device structure - * @vecs: the iovectors to write - * @count: number of vectors * @to: offset to write to - * @retlen: pointer to variable to store the number of written bytes - * @eccbuf: filesystem supplied oob data buffer - * @oobsel: oob selection structure - * - * NAND write with iovec with ecc + * @ops: oob operation description structure */ -static int nand_writev_ecc (struct mtd_info *mtd, const struct kvec *vecs, unsigned long count, - loff_t to, size_t * retlen, u_char *eccbuf, struct nand_oobinfo *oobsel) +static int nand_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) { - int i, page, len, total_len, ret = -EIO, written = 0, chipnr; - int oob, numpages, autoplace = 0, startpage; - struct nand_chip *this = mtd->priv; - int ppblock = (1 << (this->phys_erase_shift - this->page_shift)); - u_char *oobbuf, *bufstart; - - /* Preset written len for early exit */ - *retlen = 0; + struct nand_chip *chip = mtd->priv; + int ret = -ENOTSUPP; - /* Calculate total length of data */ - total_len = 0; - for (i = 0; i < count; i++) - total_len += (int) vecs[i].iov_len; - - MTDDEBUG (MTD_DEBUG_LEVEL3, - "nand_writev: to = 0x%08x, len = %i, count = %ld\n", - (unsigned int) to, (unsigned int) total_len, count); - - /* Do not allow write past end of page */ - if ((to + total_len) > mtd->size) { - MTDDEBUG (MTD_DEBUG_LEVEL0, - "nand_writev: Attempted write past end of device\n"); - return -EINVAL; - } + ops->retlen = 0; - /* reject writes, which are not page aligned */ - if (NOTALIGNED (to) || NOTALIGNED(total_len)) { - printk (KERN_NOTICE "nand_write_ecc: Attempt to write not page aligned data\n"); + /* Do not allow writes past end of device */ + if (ops->datbuf && (to + ops->len) > mtd->size) { + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: " + "Attempt read beyond end of device\n"); return -EINVAL; } - /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd, FL_WRITING); + nand_get_device(chip, mtd, FL_WRITING); - /* Get the current chip-nr */ - chipnr = (int) (to >> this->chip_shift); - /* Select the NAND device */ - this->select_chip(mtd, chipnr); + switch(ops->mode) { + case MTD_OOB_PLACE: + case MTD_OOB_AUTO: + case MTD_OOB_RAW: + break; - /* Check, if it is write protected */ - if (nand_check_wp(mtd)) + default: goto out; - - /* if oobsel is NULL, use chip defaults */ - if (oobsel == NULL) - oobsel = &mtd->oobinfo; - - /* Autoplace of oob data ? Use the default placement scheme */ - if (oobsel->useecc == MTD_NANDECC_AUTOPLACE) { - oobsel = this->autooob; - autoplace = 1; } - if (oobsel->useecc == MTD_NANDECC_AUTOPL_USR) - autoplace = 1; - - /* Setup start page */ - page = (int) (to >> this->page_shift); - /* Invalidate the page cache, if we write to the cached page */ - if (page <= this->pagebuf && this->pagebuf < ((to + total_len) >> this->page_shift)) - this->pagebuf = -1; - - startpage = page & this->pagemask; - - /* Loop until all kvec' data has been written */ - len = 0; - while (count) { - /* If the given tuple is >= pagesize then - * write it out from the iov - */ - if ((vecs->iov_len - len) >= mtd->oobblock) { - /* Calc number of pages we can write - * out of this iov in one go */ - numpages = (vecs->iov_len - len) >> this->page_shift; - /* Do not cross block boundaries */ - numpages = min (ppblock - (startpage & (ppblock - 1)), numpages); - oobbuf = nand_prepare_oobbuf (mtd, NULL, oobsel, autoplace, numpages); - bufstart = (u_char *)vecs->iov_base; - bufstart += len; - this->data_poi = bufstart; - oob = 0; - for (i = 1; i <= numpages; i++) { - /* Write one page. If this is the last page to write - * then use the real pageprogram command, else select - * cached programming if supported by the chip. - */ - ret = nand_write_page (mtd, this, page & this->pagemask, - &oobbuf[oob], oobsel, i != numpages); - if (ret) - goto out; - this->data_poi += mtd->oobblock; - len += mtd->oobblock; - oob += mtd->oobsize; - page++; - } - /* Check, if we have to switch to the next tuple */ - if (len >= (int) vecs->iov_len) { - vecs++; - len = 0; - count--; - } - } else { - /* We must use the internal buffer, read data out of each - * tuple until we have a full page to write - */ - int cnt = 0; - while (cnt < mtd->oobblock) { - if (vecs->iov_base != NULL && vecs->iov_len) - this->data_buf[cnt++] = ((u_char *) vecs->iov_base)[len++]; - /* Check, if we have to switch to the next tuple */ - if (len >= (int) vecs->iov_len) { - vecs++; - len = 0; - count--; - } - } - this->pagebuf = page; - this->data_poi = this->data_buf; - bufstart = this->data_poi; - numpages = 1; - oobbuf = nand_prepare_oobbuf (mtd, NULL, oobsel, autoplace, numpages); - ret = nand_write_page (mtd, this, page & this->pagemask, - oobbuf, oobsel, 0); - if (ret) - goto out; - page++; - } - this->data_poi = bufstart; - ret = nand_verify_pages (mtd, this, startpage, numpages, oobbuf, oobsel, chipnr, 0); - if (ret) - goto out; - - written += mtd->oobblock * numpages; - /* All done ? */ - if (!count) - break; + if (!ops->datbuf) + ret = nand_do_write_oob(mtd, to, ops); + else + ret = nand_do_write_ops(mtd, to, ops); - startpage = page & this->pagemask; - /* Check, if we cross a chip boundary */ - if (!startpage) { - chipnr++; - this->select_chip(mtd, -1); - this->select_chip(mtd, chipnr); - } - } - ret = 0; -out: - /* Deselect and wake up anyone waiting on the device */ + out: nand_release_device(mtd); - - *retlen = written; return ret; } -#endif /** * single_erease_cmd - [GENERIC] NAND standard block erase command function @@ -2094,12 +1990,12 @@ out: * * Standard erase command for NAND chips */ -static void single_erase_cmd (struct mtd_info *mtd, int page) +static void single_erase_cmd(struct mtd_info *mtd, int page) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; /* Send commands to erase a block */ - this->cmdfunc (mtd, NAND_CMD_ERASE1, -1, page); - this->cmdfunc (mtd, NAND_CMD_ERASE2, -1, -1); + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); + chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); } /** @@ -2110,15 +2006,15 @@ static void single_erase_cmd (struct mtd_info *mtd, int page) * AND multi block erase command function * Erase 4 consecutive blocks */ -static void multi_erase_cmd (struct mtd_info *mtd, int page) +static void multi_erase_cmd(struct mtd_info *mtd, int page) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; /* Send commands to erase a block */ - this->cmdfunc (mtd, NAND_CMD_ERASE1, -1, page++); - this->cmdfunc (mtd, NAND_CMD_ERASE1, -1, page++); - this->cmdfunc (mtd, NAND_CMD_ERASE1, -1, page++); - this->cmdfunc (mtd, NAND_CMD_ERASE1, -1, page); - this->cmdfunc (mtd, NAND_CMD_ERASE2, -1, -1); + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); + chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); } /** @@ -2128,35 +2024,39 @@ static void multi_erase_cmd (struct mtd_info *mtd, int page) * * Erase one ore more blocks */ -static int nand_erase (struct mtd_info *mtd, struct erase_info *instr) +static int nand_erase(struct mtd_info *mtd, struct erase_info *instr) { - return nand_erase_nand (mtd, instr, 0); + return nand_erase_nand(mtd, instr, 0); } +#define BBT_PAGE_MASK 0xffffff3f /** - * nand_erase_intern - [NAND Interface] erase block(s) + * nand_erase_nand - [Internal] erase block(s) * @mtd: MTD device structure * @instr: erase instruction * @allowbbt: allow erasing the bbt area * * Erase one ore more blocks */ -int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbbt) +int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, + int allowbbt) { int page, len, status, pages_per_block, ret, chipnr; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; + int rewrite_bbt[NAND_MAX_CHIPS]={0}; + unsigned int bbt_masked_page = 0xffffffff; MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%08x, len = %i\n", (unsigned int) instr->addr, (unsigned int) instr->len); /* Start address must align on block boundary */ - if (instr->addr & ((1 << this->phys_erase_shift) - 1)) { + if (instr->addr & ((1 << chip->phys_erase_shift) - 1)) { MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_erase: Unaligned address\n"); return -EINVAL; } /* Length must align on block boundary */ - if (instr->len & ((1 << this->phys_erase_shift) - 1)) { + if (instr->len & ((1 << chip->phys_erase_shift) - 1)) { MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_erase: Length not block aligned\n"); return -EINVAL; @@ -2172,19 +2072,18 @@ int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbb instr->fail_addr = 0xffffffff; /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd, FL_ERASING); + nand_get_device(chip, mtd, FL_ERASING); /* Shift to get first page */ - page = (int) (instr->addr >> this->page_shift); - chipnr = (int) (instr->addr >> this->chip_shift); + page = (int)(instr->addr >> chip->page_shift); + chipnr = (int)(instr->addr >> chip->chip_shift); /* Calculate pages in each block */ - pages_per_block = 1 << (this->phys_erase_shift - this->page_shift); - + pages_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); + /* Select the NAND device */ - this->select_chip(mtd, chipnr); + chip->select_chip(mtd, chipnr); - /* Check the WP bit */ /* Check, if it is write protected */ if (nand_check_wp(mtd)) { MTDDEBUG (MTD_DEBUG_LEVEL0, @@ -2193,52 +2092,92 @@ int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbb goto erase_exit; } + /* + * If BBT requires refresh, set the BBT page mask to see if the BBT + * should be rewritten. Otherwise the mask is set to 0xffffffff which + * can not be matched. This is also done when the bbt is actually + * erased to avoid recusrsive updates + */ + if (chip->options & BBT_AUTO_REFRESH && !allowbbt) + bbt_masked_page = chip->bbt_td->pages[chipnr] & BBT_PAGE_MASK; + /* Loop through the pages */ len = instr->len; instr->state = MTD_ERASING; while (len) { -#ifndef NAND_ALLOW_ERASE_ALL - /* Check if we have a bad block, we do not erase bad blocks ! */ - if (nand_block_checkbad(mtd, ((loff_t) page) << this->page_shift, 0, allowbbt)) { - printk (KERN_WARNING "nand_erase: attempt to erase a bad block at page 0x%08x\n", page); + /* + * heck if we have a bad block, we do not erase bad blocks ! + */ + if (nand_block_checkbad(mtd, ((loff_t) page) << + chip->page_shift, 0, allowbbt)) { + printk(KERN_WARNING "nand_erase: attempt to erase a " + "bad block at page 0x%08x\n", page); instr->state = MTD_ERASE_FAILED; goto erase_exit; } -#endif - /* Invalidate the page cache, if we erase the block which contains - the current cached page */ - if (page <= this->pagebuf && this->pagebuf < (page + pages_per_block)) - this->pagebuf = -1; - this->erase_cmd (mtd, page & this->pagemask); + /* + * Invalidate the page cache, if we erase the block which + * contains the current cached page + */ + if (page <= chip->pagebuf && chip->pagebuf < + (page + pages_per_block)) + chip->pagebuf = -1; + + chip->erase_cmd(mtd, page & chip->pagemask); + + status = chip->waitfunc(mtd, chip); - status = this->waitfunc (mtd, this, FL_ERASING); + /* + * See if operation failed and additional status checks are + * available + */ + if ((status & NAND_STATUS_FAIL) && (chip->errstat)) + status = chip->errstat(mtd, chip, FL_ERASING, + status, page); /* See if block erase succeeded */ - if (status & 0x01) { + if (status & NAND_STATUS_FAIL) { MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_erase: " "Failed erase, page 0x%08x\n", page); instr->state = MTD_ERASE_FAILED; - instr->fail_addr = (page << this->page_shift); + instr->fail_addr = (page << chip->page_shift); goto erase_exit; } + /* + * If BBT requires refresh, set the BBT rewrite flag to the + * page being erased + */ + if (bbt_masked_page != 0xffffffff && + (page & BBT_PAGE_MASK) == bbt_masked_page) + rewrite_bbt[chipnr] = (page << chip->page_shift); + /* Increment page address and decrement length */ - len -= (1 << this->phys_erase_shift); + len -= (1 << chip->phys_erase_shift); page += pages_per_block; /* Check, if we cross a chip boundary */ - if (len && !(page & this->pagemask)) { + if (len && !(page & chip->pagemask)) { chipnr++; - this->select_chip(mtd, -1); - this->select_chip(mtd, chipnr); + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + + /* + * If BBT requires refresh and BBT-PERCHIP, set the BBT + * page mask to see if this BBT should be rewritten + */ + if (bbt_masked_page != 0xffffffff && + (chip->bbt_td->options & NAND_BBT_PERCHIP)) + bbt_masked_page = chip->bbt_td->pages[chipnr] & + BBT_PAGE_MASK; } } instr->state = MTD_ERASE_DONE; -erase_exit: + erase_exit: ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO; /* Do call back function */ @@ -2248,6 +2187,23 @@ erase_exit: /* Deselect and wake up anyone waiting on the device */ nand_release_device(mtd); + /* + * If BBT requires refresh and erase was successful, rewrite any + * selected bad block tables + */ + if (bbt_masked_page == 0xffffffff || ret) + return ret; + + for (chipnr = 0; chipnr < chip->numchips; chipnr++) { + if (!rewrite_bbt[chipnr]) + continue; + /* update the BBT for chip */ + MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_erase_nand: nand_update_bbt " + "(%d:0x%0x 0x%0x)\n", chipnr, rewrite_bbt[chipnr], + chip->bbt_td->pages[chipnr]); + nand_update_bbt(mtd, rewrite_bbt[chipnr]); + } + /* Return more or less happy */ return ret; } @@ -2258,41 +2214,40 @@ erase_exit: * * Sync is actually a wait for chip ready function */ -static void nand_sync (struct mtd_info *mtd) +static void nand_sync(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_sync: called\n"); /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd, FL_SYNCING); + nand_get_device(chip, mtd, FL_SYNCING); /* Release it and go back */ - nand_release_device (mtd); + nand_release_device(mtd); } - /** - * nand_block_isbad - [MTD Interface] Check whether the block at the given offset is bad + * nand_block_isbad - [MTD Interface] Check if block at offset is bad * @mtd: MTD device structure - * @ofs: offset relative to mtd start + * @offs: offset relative to mtd start */ -static int nand_block_isbad (struct mtd_info *mtd, loff_t ofs) +static int nand_block_isbad(struct mtd_info *mtd, loff_t offs) { /* Check for invalid offset */ - if (ofs > mtd->size) + if (offs > mtd->size) return -EINVAL; - return nand_block_checkbad (mtd, ofs, 1, 0); + return nand_block_checkbad(mtd, offs, 1, 0); } /** - * nand_block_markbad - [MTD Interface] Mark the block at the given offset as bad + * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad * @mtd: MTD device structure * @ofs: offset relative to mtd start */ -static int nand_block_markbad (struct mtd_info *mtd, loff_t ofs) +static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; int ret; if ((ret = nand_block_isbad(mtd, ofs))) { @@ -2302,419 +2257,553 @@ static int nand_block_markbad (struct mtd_info *mtd, loff_t ofs) return ret; } - return this->block_markbad(mtd, ofs); + return chip->block_markbad(mtd, ofs); } /** - * nand_scan - [NAND Interface] Scan for the NAND device + * nand_suspend - [MTD Interface] Suspend the NAND flash * @mtd: MTD device structure - * @maxchips: Number of chips to scan for - * - * This fills out all the not initialized function pointers - * with the defaults. - * The flash ID is read and the mtd/chip structures are - * filled with the appropriate values. Buffers are allocated if - * they are not provided by the board driver - * */ -int nand_scan (struct mtd_info *mtd, int maxchips) +static int nand_suspend(struct mtd_info *mtd) { - int i, j, nand_maf_id, nand_dev_id, busw; - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; + + return nand_get_device(chip, mtd, FL_PM_SUSPENDED); +} + +/** + * nand_resume - [MTD Interface] Resume the NAND flash + * @mtd: MTD device structure + */ +static void nand_resume(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; - /* Get buswidth to select the correct functions*/ - busw = this->options & NAND_BUSWIDTH_16; + if (chip->state == FL_PM_SUSPENDED) + nand_release_device(mtd); + else + printk(KERN_ERR "nand_resume() called for a chip which is not " + "in suspended state\n"); +} +/* + * Set default functions + */ +static void nand_set_defaults(struct nand_chip *chip, int busw) +{ /* check for proper chip_delay setup, set 20us if not */ - if (!this->chip_delay) - this->chip_delay = 20; + if (!chip->chip_delay) + chip->chip_delay = 20; /* check, if a user supplied command function given */ - if (this->cmdfunc == NULL) - this->cmdfunc = nand_command; + if (chip->cmdfunc == NULL) + chip->cmdfunc = nand_command; /* check, if a user supplied wait function given */ - if (this->waitfunc == NULL) - this->waitfunc = nand_wait; - - if (!this->select_chip) - this->select_chip = nand_select_chip; - if (!this->write_byte) - this->write_byte = busw ? nand_write_byte16 : nand_write_byte; - if (!this->read_byte) - this->read_byte = busw ? nand_read_byte16 : nand_read_byte; - if (!this->write_word) - this->write_word = nand_write_word; - if (!this->read_word) - this->read_word = nand_read_word; - if (!this->block_bad) - this->block_bad = nand_block_bad; - if (!this->block_markbad) - this->block_markbad = nand_default_block_markbad; - if (!this->write_buf) - this->write_buf = busw ? nand_write_buf16 : nand_write_buf; - if (!this->read_buf) - this->read_buf = busw ? nand_read_buf16 : nand_read_buf; - if (!this->verify_buf) - this->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf; - if (!this->scan_bbt) - this->scan_bbt = nand_default_bbt; + if (chip->waitfunc == NULL) + chip->waitfunc = nand_wait; + + if (!chip->select_chip) + chip->select_chip = nand_select_chip; + if (!chip->read_byte) + chip->read_byte = busw ? nand_read_byte16 : nand_read_byte; + if (!chip->read_word) + chip->read_word = nand_read_word; + if (!chip->block_bad) + chip->block_bad = nand_block_bad; + if (!chip->block_markbad) + chip->block_markbad = nand_default_block_markbad; + if (!chip->write_buf) + chip->write_buf = busw ? nand_write_buf16 : nand_write_buf; + if (!chip->read_buf) + chip->read_buf = busw ? nand_read_buf16 : nand_read_buf; + if (!chip->verify_buf) + chip->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf; + if (!chip->scan_bbt) + chip->scan_bbt = nand_default_bbt; + + if (!chip->controller) { + chip->controller = &chip->hwcontrol; + + /* XXX U-BOOT XXX */ +#if 0 + spin_lock_init(&chip->controller->lock); + init_waitqueue_head(&chip->controller->wq); +#endif + } + +} + +/* + * Get the flash and manufacturer id and lookup if the type is supported + */ +static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, + struct nand_chip *chip, + int busw, int *maf_id) +{ + struct nand_flash_dev *type = NULL; + int i, dev_id, maf_idx; /* Select the device */ - this->select_chip(mtd, 0); + chip->select_chip(mtd, 0); /* Send the command for reading device ID */ - this->cmdfunc (mtd, NAND_CMD_READID, 0x00, -1); + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); /* Read manufacturer and device IDs */ - nand_maf_id = this->read_byte(mtd); - nand_dev_id = this->read_byte(mtd); + *maf_id = chip->read_byte(mtd); + dev_id = chip->read_byte(mtd); - /* Print and store flash device information */ + /* Lookup the flash id */ for (i = 0; nand_flash_ids[i].name != NULL; i++) { + if (dev_id == nand_flash_ids[i].id) { + type = &nand_flash_ids[i]; + break; + } + } - if (nand_dev_id != nand_flash_ids[i].id) - continue; + if (!type) + return ERR_PTR(-ENODEV); + + if (!mtd->name) + mtd->name = type->name; + + chip->chipsize = type->chipsize << 20; + + /* Newer devices have all the information in additional id bytes */ + if (!type->pagesize) { + int extid; + /* The 3rd id byte holds MLC / multichip data */ + chip->cellinfo = chip->read_byte(mtd); + /* The 4th id byte is the important one */ + extid = chip->read_byte(mtd); + /* Calc pagesize */ + mtd->writesize = 1024 << (extid & 0x3); + extid >>= 2; + /* Calc oobsize */ + mtd->oobsize = (8 << (extid & 0x01)) * (mtd->writesize >> 9); + extid >>= 2; + /* Calc blocksize. Blocksize is multiples of 64KiB */ + mtd->erasesize = (64 * 1024) << (extid & 0x03); + extid >>= 2; + /* Get buswidth information */ + busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0; - if (!mtd->name) mtd->name = nand_flash_ids[i].name; - this->chipsize = nand_flash_ids[i].chipsize << 20; - - /* New devices have all the information in additional id bytes */ - if (!nand_flash_ids[i].pagesize) { - int extid; - /* The 3rd id byte contains non relevant data ATM */ - extid = this->read_byte(mtd); - /* The 4th id byte is the important one */ - extid = this->read_byte(mtd); - /* Calc pagesize */ - mtd->oobblock = 1024 << (extid & 0x3); - extid >>= 2; - /* Calc oobsize */ - mtd->oobsize = (8 << (extid & 0x01)) * (mtd->oobblock / 512); - extid >>= 2; - /* Calc blocksize. Blocksize is multiples of 64KiB */ - mtd->erasesize = (64 * 1024) << (extid & 0x03); - extid >>= 2; - /* Get buswidth information */ - busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0; + } else { + /* + * Old devices have chip data hardcoded in the device id table + */ + mtd->erasesize = type->erasesize; + mtd->writesize = type->pagesize; + mtd->oobsize = mtd->writesize / 32; + busw = type->options & NAND_BUSWIDTH_16; + } - } else { - /* Old devices have this data hardcoded in the - * device id table */ - mtd->erasesize = nand_flash_ids[i].erasesize; - mtd->oobblock = nand_flash_ids[i].pagesize; - mtd->oobsize = mtd->oobblock / 32; - busw = nand_flash_ids[i].options & NAND_BUSWIDTH_16; - } + /* Try to identify manufacturer */ + for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) { + if (nand_manuf_ids[maf_idx].id == *maf_id) + break; + } - /* Check, if buswidth is correct. Hardware drivers should set - * this correct ! */ - if (busw != (this->options & NAND_BUSWIDTH_16)) { - printk (KERN_INFO "NAND device: Manufacturer ID:" - " 0x%02x, Chip ID: 0x%02x (%s %s)\n", nand_maf_id, nand_dev_id, - nand_manuf_ids[i].name , mtd->name); - printk (KERN_WARNING - "NAND bus width %d instead %d bit\n", - (this->options & NAND_BUSWIDTH_16) ? 16 : 8, - busw ? 16 : 8); - this->select_chip(mtd, -1); - return 1; - } + /* + * Check, if buswidth is correct. Hardware drivers should set + * chip correct ! + */ + if (busw != (chip->options & NAND_BUSWIDTH_16)) { + printk(KERN_INFO "NAND device: Manufacturer ID:" + " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, + dev_id, nand_manuf_ids[maf_idx].name, mtd->name); + printk(KERN_WARNING "NAND bus width %d instead %d bit\n", + (chip->options & NAND_BUSWIDTH_16) ? 16 : 8, + busw ? 16 : 8); + return ERR_PTR(-EINVAL); + } - /* Calculate the address shift from the page size */ - this->page_shift = ffs(mtd->oobblock) - 1; - this->bbt_erase_shift = this->phys_erase_shift = ffs(mtd->erasesize) - 1; - this->chip_shift = ffs(this->chipsize) - 1; - - /* Set the bad block position */ - this->badblockpos = mtd->oobblock > 512 ? - NAND_LARGE_BADBLOCK_POS : NAND_SMALL_BADBLOCK_POS; - - /* Get chip options, preserve non chip based options */ - this->options &= ~NAND_CHIPOPTIONS_MSK; - this->options |= nand_flash_ids[i].options & NAND_CHIPOPTIONS_MSK; - /* Set this as a default. Board drivers can override it, if neccecary */ - this->options |= NAND_NO_AUTOINCR; - /* Check if this is a not a samsung device. Do not clear the options - * for chips which are not having an extended id. - */ - if (nand_maf_id != NAND_MFR_SAMSUNG && !nand_flash_ids[i].pagesize) - this->options &= ~NAND_SAMSUNG_LP_OPTIONS; + /* Calculate the address shift from the page size */ + chip->page_shift = ffs(mtd->writesize) - 1; + /* Convert chipsize to number of pages per chip -1. */ + chip->pagemask = (chip->chipsize >> chip->page_shift) - 1; - /* Check for AND chips with 4 page planes */ - if (this->options & NAND_4PAGE_ARRAY) - this->erase_cmd = multi_erase_cmd; - else - this->erase_cmd = single_erase_cmd; + chip->bbt_erase_shift = chip->phys_erase_shift = + ffs(mtd->erasesize) - 1; + chip->chip_shift = ffs(chip->chipsize) - 1; - /* Do not replace user supplied command function ! */ - if (mtd->oobblock > 512 && this->cmdfunc == nand_command) - this->cmdfunc = nand_command_lp; + /* Set the bad block position */ + chip->badblockpos = mtd->writesize > 512 ? + NAND_LARGE_BADBLOCK_POS : NAND_SMALL_BADBLOCK_POS; - /* Try to identify manufacturer */ - for (j = 0; nand_manuf_ids[j].id != 0x0; j++) { - if (nand_manuf_ids[j].id == nand_maf_id) - break; - } - break; - } + /* Get chip options, preserve non chip based options */ + chip->options &= ~NAND_CHIPOPTIONS_MSK; + chip->options |= type->options & NAND_CHIPOPTIONS_MSK; - if (!nand_flash_ids[i].name) { -#ifndef CFG_NAND_QUIET_TEST - printk (KERN_WARNING "No NAND device found!!!\n"); -#endif - this->select_chip(mtd, -1); - return 1; - } + /* + * Set chip as a default. Board drivers can override it, if necessary + */ + chip->options |= NAND_NO_AUTOINCR; - for (i=1; i < maxchips; i++) { - this->select_chip(mtd, i); + /* Check if chip is a not a samsung device. Do not clear the + * options for chips which are not having an extended id. + */ + if (*maf_id != NAND_MFR_SAMSUNG && !type->pagesize) + chip->options &= ~NAND_SAMSUNG_LP_OPTIONS; - /* Send the command for reading device ID */ - this->cmdfunc (mtd, NAND_CMD_READID, 0x00, -1); + /* Check for AND chips with 4 page planes */ + if (chip->options & NAND_4PAGE_ARRAY) + chip->erase_cmd = multi_erase_cmd; + else + chip->erase_cmd = single_erase_cmd; + + /* Do not replace user supplied command function ! */ + if (mtd->writesize > 512 && chip->cmdfunc == nand_command) + chip->cmdfunc = nand_command_lp; + + printk(KERN_INFO "NAND device: Manufacturer ID:" + " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, dev_id, + nand_manuf_ids[maf_idx].name, type->name); + + return type; +} + +/** + * nand_scan_ident - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * @maxchips: Number of chips to scan for + * + * This is the first phase of the normal nand_scan() function. It + * reads the flash ID and sets up MTD fields accordingly. + * + * The mtd->owner field must be set to the module of the caller. + */ +int nand_scan_ident(struct mtd_info *mtd, int maxchips) +{ + int i, busw, nand_maf_id; + struct nand_chip *chip = mtd->priv; + struct nand_flash_dev *type; + + /* Get buswidth to select the correct functions */ + busw = chip->options & NAND_BUSWIDTH_16; + /* Set the default functions */ + nand_set_defaults(chip, busw); + + /* Read the flash type */ + type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id); + + if (IS_ERR(type)) { + printk(KERN_WARNING "No NAND device found!!!\n"); + chip->select_chip(mtd, -1); + return PTR_ERR(type); + } + /* Check for a chip array */ + for (i = 1; i < maxchips; i++) { + chip->select_chip(mtd, i); + /* Send the command for reading device ID */ + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); /* Read manufacturer and device IDs */ - if (nand_maf_id != this->read_byte(mtd) || - nand_dev_id != this->read_byte(mtd)) + if (nand_maf_id != chip->read_byte(mtd) || + type->id != chip->read_byte(mtd)) break; } if (i > 1) printk(KERN_INFO "%d NAND chips detected\n", i); - /* Allocate buffers, if neccecary */ - if (!this->oob_buf) { - size_t len; - len = mtd->oobsize << (this->phys_erase_shift - this->page_shift); - this->oob_buf = kmalloc (len, GFP_KERNEL); - if (!this->oob_buf) { - printk (KERN_ERR "nand_scan(): Cannot allocate oob_buf\n"); - return -ENOMEM; - } - this->options |= NAND_OOBBUF_ALLOC; - } + /* Store the number of chips and calc total size for mtd */ + chip->numchips = i; + mtd->size = i * chip->chipsize; - if (!this->data_buf) { - size_t len; - len = mtd->oobblock + mtd->oobsize; - this->data_buf = kmalloc (len, GFP_KERNEL); - if (!this->data_buf) { - if (this->options & NAND_OOBBUF_ALLOC) - kfree (this->oob_buf); - printk (KERN_ERR "nand_scan(): Cannot allocate data_buf\n"); - return -ENOMEM; - } - this->options |= NAND_DATABUF_ALLOC; - } + return 0; +} - /* Store the number of chips and calc total size for mtd */ - this->numchips = i; - mtd->size = i * this->chipsize; - /* Convert chipsize to number of pages per chip -1. */ - this->pagemask = (this->chipsize >> this->page_shift) - 1; - /* Preset the internal oob buffer */ - memset(this->oob_buf, 0xff, mtd->oobsize << (this->phys_erase_shift - this->page_shift)); - - /* If no default placement scheme is given, select an - * appropriate one */ - if (!this->autooob) { - /* Select the appropriate default oob placement scheme for - * placement agnostic filesystems */ + +/** + * nand_scan_tail - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * @maxchips: Number of chips to scan for + * + * This is the second phase of the normal nand_scan() function. It + * fills out all the uninitialized function pointers with the defaults + * and scans for a bad block table if appropriate. + */ +int nand_scan_tail(struct mtd_info *mtd) +{ + int i; + struct nand_chip *chip = mtd->priv; + + if (!(chip->options & NAND_OWN_BUFFERS)) + chip->buffers = kmalloc(sizeof(*chip->buffers), GFP_KERNEL); + if (!chip->buffers) + return -ENOMEM; + + /* Set the internal oob buffer location, just after the page data */ + chip->oob_poi = chip->buffers->databuf + mtd->writesize; + + /* + * If no default placement scheme is given, select an appropriate one + */ + if (!chip->ecc.layout) { switch (mtd->oobsize) { case 8: - this->autooob = &nand_oob_8; + chip->ecc.layout = &nand_oob_8; break; case 16: - this->autooob = &nand_oob_16; + chip->ecc.layout = &nand_oob_16; break; case 64: - this->autooob = &nand_oob_64; + chip->ecc.layout = &nand_oob_64; break; case 128: - this->autooob = &nand_oob_128; + chip->ecc.layout = &nand_oob_128; break; default: - printk (KERN_WARNING "No oob scheme defined for oobsize %d\n", - mtd->oobsize); -/* BUG(); */ + printk(KERN_WARNING "No oob scheme defined for " + "oobsize %d\n", mtd->oobsize); +// BUG(); } } - /* The number of bytes available for the filesystem to place fs dependend - * oob data */ - mtd->oobavail = 0; - for (i=0; this->autooob->oobfree[i][1]; i++) - mtd->oobavail += this->autooob->oobfree[i][1]; + if (!chip->write_page) + chip->write_page = nand_write_page; /* - * check ECC mode, default to software - * if 3byte/512byte hardware ECC is selected and we have 256 byte pagesize - * fallback to software ECC - */ - this->eccsize = 256; /* set default eccsize */ - this->eccbytes = 3; - - switch (this->eccmode) { - case NAND_ECC_HW12_2048: - if (mtd->oobblock < 2048) { - printk(KERN_WARNING "2048 byte HW ECC not possible on %d byte page size, fallback to SW ECC\n", - mtd->oobblock); - this->eccmode = NAND_ECC_SOFT; - this->calculate_ecc = nand_calculate_ecc; - this->correct_data = nand_correct_data; - } else - this->eccsize = 2048; - break; - - case NAND_ECC_HW3_512: - case NAND_ECC_HW6_512: - case NAND_ECC_HW8_512: - if (mtd->oobblock == 256) { - printk (KERN_WARNING "512 byte HW ECC not possible on 256 Byte pagesize, fallback to SW ECC \n"); - this->eccmode = NAND_ECC_SOFT; - this->calculate_ecc = nand_calculate_ecc; - this->correct_data = nand_correct_data; - } else - this->eccsize = 512; /* set eccsize to 512 */ - break; + * check ECC mode, default to software if 3byte/512byte hardware ECC is + * selected and we have 256 byte pagesize fallback to software ECC + */ + if (!chip->ecc.read_page_raw) + chip->ecc.read_page_raw = nand_read_page_raw; + if (!chip->ecc.write_page_raw) + chip->ecc.write_page_raw = nand_write_page_raw; + + switch (chip->ecc.mode) { + case NAND_ECC_HW: + /* Use standard hwecc read page function ? */ + if (!chip->ecc.read_page) + chip->ecc.read_page = nand_read_page_hwecc; + if (!chip->ecc.write_page) + chip->ecc.write_page = nand_write_page_hwecc; + if (!chip->ecc.read_oob) + chip->ecc.read_oob = nand_read_oob_std; + if (!chip->ecc.write_oob) + chip->ecc.write_oob = nand_write_oob_std; + + case NAND_ECC_HW_SYNDROME: + if (!chip->ecc.calculate || !chip->ecc.correct || + !chip->ecc.hwctl) { + printk(KERN_WARNING "No ECC functions supplied, " + "Hardware ECC not possible\n"); + BUG(); + } + /* Use standard syndrome read/write page function ? */ + if (!chip->ecc.read_page) + chip->ecc.read_page = nand_read_page_syndrome; + if (!chip->ecc.write_page) + chip->ecc.write_page = nand_write_page_syndrome; + if (!chip->ecc.read_oob) + chip->ecc.read_oob = nand_read_oob_syndrome; + if (!chip->ecc.write_oob) + chip->ecc.write_oob = nand_write_oob_syndrome; + + if (mtd->writesize >= chip->ecc.size) + break; + printk(KERN_WARNING "%d byte HW ECC not possible on " + "%d byte page size, fallback to SW ECC\n", + chip->ecc.size, mtd->writesize); + chip->ecc.mode = NAND_ECC_SOFT; - case NAND_ECC_HW3_256: + case NAND_ECC_SOFT: + chip->ecc.calculate = nand_calculate_ecc; + chip->ecc.correct = nand_correct_data; + chip->ecc.read_page = nand_read_page_swecc; + chip->ecc.write_page = nand_write_page_swecc; + chip->ecc.read_oob = nand_read_oob_std; + chip->ecc.write_oob = nand_write_oob_std; + chip->ecc.size = 256; + chip->ecc.bytes = 3; break; case NAND_ECC_NONE: - printk (KERN_WARNING "NAND_ECC_NONE selected by board driver. This is not recommended !!\n"); - this->eccmode = NAND_ECC_NONE; - break; - - case NAND_ECC_SOFT: - this->calculate_ecc = nand_calculate_ecc; - this->correct_data = nand_correct_data; + printk(KERN_WARNING "NAND_ECC_NONE selected by board driver. " + "This is not recommended !!\n"); + chip->ecc.read_page = nand_read_page_raw; + chip->ecc.write_page = nand_write_page_raw; + chip->ecc.read_oob = nand_read_oob_std; + chip->ecc.write_oob = nand_write_oob_std; + chip->ecc.size = mtd->writesize; + chip->ecc.bytes = 0; break; default: - printk (KERN_WARNING "Invalid NAND_ECC_MODE %d\n", this->eccmode); -/* BUG(); */ - } - - /* Check hardware ecc function availability and adjust number of ecc bytes per - * calculation step - */ - switch (this->eccmode) { - case NAND_ECC_HW12_2048: - this->eccbytes += 4; - case NAND_ECC_HW8_512: - this->eccbytes += 2; - case NAND_ECC_HW6_512: - this->eccbytes += 3; - case NAND_ECC_HW3_512: - case NAND_ECC_HW3_256: - if (this->calculate_ecc && this->correct_data && this->enable_hwecc) - break; - printk (KERN_WARNING "No ECC functions supplied, Hardware ECC not possible\n"); -/* BUG(); */ + printk(KERN_WARNING "Invalid NAND_ECC_MODE %d\n", + chip->ecc.mode); + BUG(); } - mtd->eccsize = this->eccsize; + /* + * The number of bytes available for a client to place data into + * the out of band area + */ + chip->ecc.layout->oobavail = 0; + for (i = 0; chip->ecc.layout->oobfree[i].length; i++) + chip->ecc.layout->oobavail += + chip->ecc.layout->oobfree[i].length; + mtd->oobavail = chip->ecc.layout->oobavail; - /* Set the number of read / write steps for one page to ensure ECC generation */ - switch (this->eccmode) { - case NAND_ECC_HW12_2048: - this->eccsteps = mtd->oobblock / 2048; - break; - case NAND_ECC_HW3_512: - case NAND_ECC_HW6_512: - case NAND_ECC_HW8_512: - this->eccsteps = mtd->oobblock / 512; - break; - case NAND_ECC_HW3_256: - case NAND_ECC_SOFT: - this->eccsteps = mtd->oobblock / 256; - break; + /* + * Set the number of read / write steps for one page depending on ECC + * mode + */ + chip->ecc.steps = mtd->writesize / chip->ecc.size; + if(chip->ecc.steps * chip->ecc.size != mtd->writesize) { + printk(KERN_WARNING "Invalid ecc parameters\n"); + BUG(); + } + chip->ecc.total = chip->ecc.steps * chip->ecc.bytes; - case NAND_ECC_NONE: - this->eccsteps = 1; - break; + /* + * Allow subpage writes up to ecc.steps. Not possible for MLC + * FLASH. + */ + if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && + !(chip->cellinfo & NAND_CI_CELLTYPE_MSK)) { + switch(chip->ecc.steps) { + case 2: + mtd->subpage_sft = 1; + break; + case 4: + case 8: + mtd->subpage_sft = 2; + break; + } } + chip->subpagesize = mtd->writesize >> mtd->subpage_sft; -/* XXX U-BOOT XXX */ -#if 0 - /* Initialize state, waitqueue and spinlock */ - this->state = FL_READY; - init_waitqueue_head (&this->wq); - spin_lock_init (&this->chip_lock); -#endif + /* Initialize state */ + chip->state = FL_READY; /* De-select the device */ - this->select_chip(mtd, -1); + chip->select_chip(mtd, -1); /* Invalidate the pagebuffer reference */ - this->pagebuf = -1; + chip->pagebuf = -1; /* Fill in remaining MTD driver data */ mtd->type = MTD_NANDFLASH; - mtd->flags = MTD_CAP_NANDFLASH | MTD_ECC; - mtd->ecctype = MTD_ECC_SW; + mtd->flags = MTD_CAP_NANDFLASH; mtd->erase = nand_erase; mtd->point = NULL; mtd->unpoint = NULL; mtd->read = nand_read; mtd->write = nand_write; - mtd->read_ecc = nand_read_ecc; - mtd->write_ecc = nand_write_ecc; mtd->read_oob = nand_read_oob; mtd->write_oob = nand_write_oob; -/* XXX U-BOOT XXX */ -#if 0 - mtd->readv = NULL; - mtd->writev = nand_writev; - mtd->writev_ecc = nand_writev_ecc; -#endif mtd->sync = nand_sync; -/* XXX U-BOOT XXX */ -#if 0 mtd->lock = NULL; mtd->unlock = NULL; - mtd->suspend = NULL; - mtd->resume = NULL; -#endif + mtd->suspend = nand_suspend; + mtd->resume = nand_resume; mtd->block_isbad = nand_block_isbad; mtd->block_markbad = nand_block_markbad; - /* and make the autooob the default one */ - memcpy(&mtd->oobinfo, this->autooob, sizeof(mtd->oobinfo)); -/* XXX U-BOOT XXX */ + /* propagate ecc.layout to mtd_info */ + mtd->ecclayout = chip->ecc.layout; + + /* Check, if we should skip the bad block table scan */ + if (chip->options & NAND_SKIP_BBTSCAN) + return 0; + + /* Build bad block table */ + return chip->scan_bbt(mtd); +} + +/* module_text_address() isn't exported, and it's mostly a pointless + test if this is a module _anyway_ -- they'd have to try _really_ hard + to call us from in-kernel code if the core NAND support is modular. */ +#ifdef MODULE +#define caller_is_module() (1) +#else +#define caller_is_module() \ + module_text_address((unsigned long)__builtin_return_address(0)) +#endif + +/** + * nand_scan - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * @maxchips: Number of chips to scan for + * + * This fills out all the uninitialized function pointers + * with the defaults. + * The flash ID is read and the mtd/chip structures are + * filled with the appropriate values. + * The mtd->owner field must be set to the module of the caller + * + */ +int nand_scan(struct mtd_info *mtd, int maxchips) +{ + int ret; + + /* Many callers got this wrong, so check for it for a while... */ + /* XXX U-BOOT XXX */ #if 0 - mtd->owner = THIS_MODULE; + if (!mtd->owner && caller_is_module()) { + printk(KERN_CRIT "nand_scan() called with NULL mtd->owner!\n"); + BUG(); + } #endif - /* Build bad block table */ - return this->scan_bbt (mtd); + + ret = nand_scan_ident(mtd, maxchips); + if (!ret) + ret = nand_scan_tail(mtd); + return ret; } /** * nand_release - [NAND Interface] Free resources held by the NAND device * @mtd: MTD device structure - */ -void nand_release (struct mtd_info *mtd) +*/ +void nand_release(struct mtd_info *mtd) { - struct nand_chip *this = mtd->priv; + struct nand_chip *chip = mtd->priv; #ifdef CONFIG_MTD_PARTITIONS /* Deregister partitions */ - del_mtd_partitions (mtd); + del_mtd_partitions(mtd); #endif /* Deregister the device */ -/* XXX U-BOOT XXX */ + /* XXX U-BOOT XXX */ #if 0 - del_mtd_device (mtd); + del_mtd_device(mtd); #endif - /* Free bad block table memory, if allocated */ - if (this->bbt) - kfree (this->bbt); - /* Buffer allocated by nand_scan ? */ - if (this->options & NAND_OOBBUF_ALLOC) - kfree (this->oob_buf); - /* Buffer allocated by nand_scan ? */ - if (this->options & NAND_DATABUF_ALLOC) - kfree (this->data_buf); + + /* Free bad block table memory */ + kfree(chip->bbt); + if (!(chip->options & NAND_OWN_BUFFERS)) + kfree(chip->buffers); +} + +/* XXX U-BOOT XXX */ +#if 0 +EXPORT_SYMBOL_GPL(nand_scan); +EXPORT_SYMBOL_GPL(nand_scan_ident); +EXPORT_SYMBOL_GPL(nand_scan_tail); +EXPORT_SYMBOL_GPL(nand_release); + +static int __init nand_base_init(void) +{ + led_trigger_register_simple("nand-disk", &nand_led_trigger); + return 0; +} + +static void __exit nand_base_exit(void) +{ + led_trigger_unregister_simple(nand_led_trigger); } +module_init(nand_base_init); +module_exit(nand_base_exit); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Steven J. Hill , Thomas Gleixner "); +MODULE_DESCRIPTION("Generic NAND flash driver code"); +#endif + #endif + diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c index a97743b45e..acf1cf5433 100644 --- a/drivers/mtd/nand/nand_bbt.c +++ b/drivers/mtd/nand/nand_bbt.c @@ -6,7 +6,7 @@ * * Copyright (C) 2004 Thomas Gleixner (tglx@linutronix.de) * - * $Id: nand_bbt.c,v 1.28 2004/11/13 10:19:09 gleixner Exp $ + * $Id: nand_bbt.c,v 1.36 2005/11/07 11:14:30 gleixner Exp $ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -48,7 +48,7 @@ * * Following assumptions are made: * - bbts start at a page boundary, if autolocated on a block boundary - * - the space neccecary for a bbt in FLASH does not exceed a block boundary + * - the space necessary for a bbt in FLASH does not exceed a block boundary * */ @@ -63,6 +63,19 @@ #include +/* XXX U-BOOT XXX */ +#if 0 +#include +#include +#include +#include +#include +#include +#include +#include +#include +#endif + /** * check_pattern - [GENERIC] check if a pattern is in the buffer * @buf: the buffer to search @@ -76,9 +89,9 @@ * pattern area contain 0xff * */ -static int check_pattern (uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td) +static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td) { - int i, end; + int i, end = 0; uint8_t *p = buf; end = paglen + td->offs; @@ -96,9 +109,9 @@ static int check_pattern (uint8_t *buf, int len, int paglen, struct nand_bbt_des return -1; } - p += td->len; - end += td->len; if (td->options & NAND_BBT_SCANEMPTY) { + p += td->len; + end += td->len; for (i = end; i < len; i++) { if (*p++ != 0xff) return -1; @@ -107,6 +120,29 @@ static int check_pattern (uint8_t *buf, int len, int paglen, struct nand_bbt_des return 0; } +/** + * check_short_pattern - [GENERIC] check if a pattern is in the buffer + * @buf: the buffer to search + * @td: search pattern descriptor + * + * Check for a pattern at the given place. Used to search bad block + * tables and good / bad block identifiers. Same as check_pattern, but + * no optional empty check + * +*/ +static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td) +{ + int i; + uint8_t *p = buf; + + /* Compare the pattern */ + for (i = 0; i < td->len; i++) { + if (p[td->offs + i] != td->pattern[i]) + return -1; + } + return 0; +} + /** * read_bbt - [GENERIC] Read the bad block table starting from page * @mtd: MTD device structure @@ -120,8 +156,8 @@ static int check_pattern (uint8_t *buf, int len, int paglen, struct nand_bbt_des * Read the bad block table starting from page. * */ -static int read_bbt (struct mtd_info *mtd, uint8_t *buf, int page, int num, - int bits, int offs, int reserved_block_code) +static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num, + int bits, int offs, int reserved_block_code) { int res, i, j, act = 0; struct nand_chip *this = mtd->priv; @@ -130,17 +166,17 @@ static int read_bbt (struct mtd_info *mtd, uint8_t *buf, int page, int num, uint8_t msk = (uint8_t) ((1 << bits) - 1); totlen = (num * bits) >> 3; - from = ((loff_t)page) << this->page_shift; + from = ((loff_t) page) << this->page_shift; while (totlen) { - len = min (totlen, (size_t) (1 << this->bbt_erase_shift)); - res = mtd->read_ecc (mtd, from, len, &retlen, buf, NULL, this->autooob); + len = min(totlen, (size_t) (1 << this->bbt_erase_shift)); + res = mtd->read(mtd, from, len, &retlen, buf); if (res < 0) { if (retlen != len) { - printk (KERN_INFO "nand_bbt: Error reading bad block table\n"); + printk(KERN_INFO "nand_bbt: Error reading bad block table\n"); return res; } - printk (KERN_WARNING "nand_bbt: ECC error while reading bad block table\n"); + printk(KERN_WARNING "nand_bbt: ECC error while reading bad block table\n"); } /* Analyse data */ @@ -150,22 +186,23 @@ static int read_bbt (struct mtd_info *mtd, uint8_t *buf, int page, int num, uint8_t tmp = (dat >> j) & msk; if (tmp == msk) continue; - if (reserved_block_code && - (tmp == reserved_block_code)) { - printk (KERN_DEBUG "nand_read_bbt: Reserved block at 0x%08x\n", - ((offs << 2) + (act >> 1)) << this->bbt_erase_shift); + if (reserved_block_code && (tmp == reserved_block_code)) { + printk(KERN_DEBUG "nand_read_bbt: Reserved block at 0x%08x\n", + ((offs << 2) + (act >> 1)) << this->bbt_erase_shift); this->bbt[offs + (act >> 3)] |= 0x2 << (act & 0x06); + mtd->ecc_stats.bbtblocks++; continue; } /* Leave it for now, if its matured we can move this * message to MTD_DEBUG_LEVEL0 */ - printk (KERN_DEBUG "nand_read_bbt: Bad block at 0x%08x\n", - ((offs << 2) + (act >> 1)) << this->bbt_erase_shift); + printk(KERN_DEBUG "nand_read_bbt: Bad block at 0x%08x\n", + ((offs << 2) + (act >> 1)) << this->bbt_erase_shift); /* Factory marked bad or worn out ? */ if (tmp == 0) this->bbt[offs + (act >> 3)] |= 0x3 << (act & 0x06); else this->bbt[offs + (act >> 3)] |= 0x1 << (act & 0x06); + mtd->ecc_stats.badblocks++; } } totlen -= len; @@ -185,7 +222,7 @@ static int read_bbt (struct mtd_info *mtd, uint8_t *buf, int page, int num, * Read the bad block table for all chips starting at a given page * We assume that the bbt bits are in consecutive order. */ -static int read_abs_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td, int chip) +static int read_abs_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td, int chip) { struct nand_chip *this = mtd->priv; int res = 0, i; @@ -209,6 +246,42 @@ static int read_abs_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_des return 0; } +/* + * Scan read raw data from flash + */ +static int scan_read_raw(struct mtd_info *mtd, uint8_t *buf, loff_t offs, + size_t len) +{ + struct mtd_oob_ops ops; + + ops.mode = MTD_OOB_RAW; + ops.ooboffs = 0; + ops.ooblen = mtd->oobsize; + ops.oobbuf = buf; + ops.datbuf = buf; + ops.len = len; + + return mtd->read_oob(mtd, offs, &ops); +} + +/* + * Scan write data with oob to flash + */ +static int scan_write_bbt(struct mtd_info *mtd, loff_t offs, size_t len, + uint8_t *buf, uint8_t *oob) +{ + struct mtd_oob_ops ops; + + ops.mode = MTD_OOB_PLACE; + ops.ooboffs = 0; + ops.ooblen = mtd->oobsize; + ops.datbuf = buf; + ops.oobbuf = oob; + ops.len = len; + + return mtd->write_oob(mtd, offs, &ops); +} + /** * read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page * @mtd: MTD device structure @@ -220,28 +293,84 @@ static int read_abs_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_des * We assume that the bbt bits are in consecutive order. * */ -static int read_abs_bbts (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td, - struct nand_bbt_descr *md) +static int read_abs_bbts(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *td, struct nand_bbt_descr *md) { struct nand_chip *this = mtd->priv; /* Read the primary version, if available */ if (td->options & NAND_BBT_VERSION) { - nand_read_raw (mtd, buf, td->pages[0] << this->page_shift, mtd->oobblock, mtd->oobsize); - td->version[0] = buf[mtd->oobblock + td->veroffs]; - printk (KERN_DEBUG "Bad block table at page %d, version 0x%02X\n", td->pages[0], td->version[0]); + scan_read_raw(mtd, buf, td->pages[0] << this->page_shift, + mtd->writesize); + td->version[0] = buf[mtd->writesize + td->veroffs]; + printk(KERN_DEBUG "Bad block table at page %d, version 0x%02X\n", + td->pages[0], td->version[0]); } /* Read the mirror version, if available */ if (md && (md->options & NAND_BBT_VERSION)) { - nand_read_raw (mtd, buf, md->pages[0] << this->page_shift, mtd->oobblock, mtd->oobsize); - md->version[0] = buf[mtd->oobblock + md->veroffs]; - printk (KERN_DEBUG "Bad block table at page %d, version 0x%02X\n", md->pages[0], md->version[0]); + scan_read_raw(mtd, buf, md->pages[0] << this->page_shift, + mtd->writesize); + md->version[0] = buf[mtd->writesize + md->veroffs]; + printk(KERN_DEBUG "Bad block table at page %d, version 0x%02X\n", + md->pages[0], md->version[0]); } - return 1; } +/* + * Scan a given block full + */ +static int scan_block_full(struct mtd_info *mtd, struct nand_bbt_descr *bd, + loff_t offs, uint8_t *buf, size_t readlen, + int scanlen, int len) +{ + int ret, j; + + ret = scan_read_raw(mtd, buf, offs, readlen); + if (ret) + return ret; + + for (j = 0; j < len; j++, buf += scanlen) { + if (check_pattern(buf, scanlen, mtd->writesize, bd)) + return 1; + } + return 0; +} + +/* + * Scan a given block partially + */ +static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd, + loff_t offs, uint8_t *buf, int len) +{ + struct mtd_oob_ops ops; + int j, ret; + + ops.ooblen = mtd->oobsize; + ops.oobbuf = buf; + ops.ooboffs = 0; + ops.datbuf = NULL; + ops.mode = MTD_OOB_PLACE; + + for (j = 0; j < len; j++) { + /* + * Read the full oob until read_oob is fixed to + * handle single byte reads for 16 bit + * buswidth + */ + ret = mtd->read_oob(mtd, offs, &ops); + if (ret) + return ret; + + if (check_short_pattern(buf, bd)) + return 1; + + offs += mtd->writesize; + } + return 0; +} + /** * create_bbt - [GENERIC] Create a bad block table by scanning the device * @mtd: MTD device structure @@ -253,13 +382,16 @@ static int read_abs_bbts (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_de * Create a bad block table by scanning the device * for the given good/bad block identify pattern */ -static void create_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd, int chip) +static int create_bbt(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *bd, int chip) { struct nand_chip *this = mtd->priv; - int i, j, numblocks, len, scanlen; + int i, numblocks, len, scanlen; int startblock; loff_t from; - size_t readlen, ooblen; + size_t readlen; + + printk(KERN_INFO "Scanning device for bad blocks\n"); if (bd->options & NAND_BBT_SCANALLPAGES) len = 1 << (this->bbt_erase_shift - this->page_shift); @@ -269,21 +401,28 @@ static void create_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc else len = 1; } - scanlen = mtd->oobblock + mtd->oobsize; - readlen = len * mtd->oobblock; - ooblen = len * mtd->oobsize; + + if (!(bd->options & NAND_BBT_SCANEMPTY)) { + /* We need only read few bytes from the OOB area */ + scanlen = 0; + readlen = bd->len; + } else { + /* Full page content should be read */ + scanlen = mtd->writesize + mtd->oobsize; + readlen = len * mtd->writesize; + } if (chip == -1) { - /* Note that numblocks is 2 * (real numblocks) here, see i+=2 below as it - * makes shifting and masking less painful */ + /* Note that numblocks is 2 * (real numblocks) here, see i+=2 + * below as it makes shifting and masking less painful */ numblocks = mtd->size >> (this->bbt_erase_shift - 1); startblock = 0; from = 0; } else { if (chip >= this->numchips) { - printk (KERN_WARNING "create_bbt(): chipnr (%d) > available chips (%d)\n", - chip + 1, this->numchips); - return; + printk(KERN_WARNING "create_bbt(): chipnr (%d) > available chips (%d)\n", + chip + 1, this->numchips); + return -EINVAL; } numblocks = this->chipsize >> (this->bbt_erase_shift - 1); startblock = chip * numblocks; @@ -292,16 +431,28 @@ static void create_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc } for (i = startblock; i < numblocks;) { - nand_read_raw (mtd, buf, from, readlen, ooblen); - for (j = 0; j < len; j++) { - if (check_pattern (&buf[j * scanlen], scanlen, mtd->oobblock, bd)) { - this->bbt[i >> 3] |= 0x03 << (i & 0x6); - break; - } + int ret; + + if (bd->options & NAND_BBT_SCANALLPAGES) + ret = scan_block_full(mtd, bd, from, buf, readlen, + scanlen, len); + else + ret = scan_block_fast(mtd, bd, from, buf, len); + + if (ret < 0) + return ret; + + if (ret) { + this->bbt[i >> 3] |= 0x03 << (i & 0x6); + printk(KERN_WARNING "Bad eraseblock %d at 0x%08x\n", + i >> 1, (unsigned int)from); + mtd->ecc_stats.badblocks++; } + i += 2; from += (1 << this->bbt_erase_shift); } + return 0; } /** @@ -316,22 +467,23 @@ static void create_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc * block. * If the option NAND_BBT_PERCHIP is given, each chip is searched * for a bbt, which contains the bad block information of this chip. - * This is neccecary to provide support for certain DOC devices. + * This is necessary to provide support for certain DOC devices. * * The bbt ident pattern resides in the oob area of the first page * in a block. */ -static int search_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td) +static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td) { struct nand_chip *this = mtd->priv; int i, chips; int bits, startblock, block, dir; - int scanlen = mtd->oobblock + mtd->oobsize; + int scanlen = mtd->writesize + mtd->oobsize; int bbtblocks; + int blocktopage = this->bbt_erase_shift - this->page_shift; /* Search direction top -> down ? */ if (td->options & NAND_BBT_LASTBLOCK) { - startblock = (mtd->size >> this->bbt_erase_shift) -1; + startblock = (mtd->size >> this->bbt_erase_shift) - 1; dir = -1; } else { startblock = 0; @@ -357,13 +509,16 @@ static int search_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr td->pages[i] = -1; /* Scan the maximum number of blocks */ for (block = 0; block < td->maxblocks; block++) { + int actblock = startblock + dir * block; + loff_t offs = actblock << this->bbt_erase_shift; + /* Read first page */ - nand_read_raw (mtd, buf, actblock << this->bbt_erase_shift, mtd->oobblock, mtd->oobsize); - if (!check_pattern(buf, scanlen, mtd->oobblock, td)) { - td->pages[i] = actblock << (this->bbt_erase_shift - this->page_shift); + scan_read_raw(mtd, buf, offs, mtd->writesize); + if (!check_pattern(buf, scanlen, mtd->writesize, td)) { + td->pages[i] = actblock << blocktopage; if (td->options & NAND_BBT_VERSION) { - td->version[i] = buf[mtd->oobblock + td->veroffs]; + td->version[i] = buf[mtd->writesize + td->veroffs]; } break; } @@ -373,9 +528,10 @@ static int search_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr /* Check, if we found a bbt for each requested chip */ for (i = 0; i < chips; i++) { if (td->pages[i] == -1) - printk (KERN_WARNING "Bad block table not found for chip %d\n", i); + printk(KERN_WARNING "Bad block table not found for chip %d\n", i); else - printk (KERN_DEBUG "Bad block table found at page %d, version 0x%02X\n", td->pages[i], td->version[i]); + printk(KERN_DEBUG "Bad block table found at page %d, version 0x%02X\n", td->pages[i], + td->version[i]); } return 0; } @@ -389,21 +545,19 @@ static int search_bbt (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr * * Search and read the bad block table(s) */ -static int search_read_bbts (struct mtd_info *mtd, uint8_t *buf, - struct nand_bbt_descr *td, struct nand_bbt_descr *md) +static int search_read_bbts(struct mtd_info *mtd, uint8_t * buf, struct nand_bbt_descr *td, struct nand_bbt_descr *md) { /* Search the primary table */ - search_bbt (mtd, buf, td); + search_bbt(mtd, buf, td); /* Search the mirror table */ if (md) - search_bbt (mtd, buf, md); + search_bbt(mtd, buf, md); /* Force result check */ return 1; } - /** * write_bbt - [GENERIC] (Re)write the bad block table * @@ -416,25 +570,31 @@ static int search_read_bbts (struct mtd_info *mtd, uint8_t *buf, * (Re)write the bad block table * */ -static int write_bbt (struct mtd_info *mtd, uint8_t *buf, - struct nand_bbt_descr *td, struct nand_bbt_descr *md, int chipsel) +static int write_bbt(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *td, struct nand_bbt_descr *md, + int chipsel) { struct nand_chip *this = mtd->priv; - struct nand_oobinfo oobinfo; struct erase_info einfo; int i, j, res, chip = 0; int bits, startblock, dir, page, offs, numblocks, sft, sftmsk; - int nrchips, bbtoffs, pageoffs; + int nrchips, bbtoffs, pageoffs, ooboffs; uint8_t msk[4]; uint8_t rcode = td->reserved_block_code; size_t retlen, len = 0; loff_t to; + struct mtd_oob_ops ops; + + ops.ooblen = mtd->oobsize; + ops.ooboffs = 0; + ops.datbuf = NULL; + ops.mode = MTD_OOB_PLACE; if (!rcode) rcode = 0xff; /* Write bad block table per chip rather than per device ? */ if (td->options & NAND_BBT_PERCHIP) { - numblocks = (int) (this->chipsize >> this->bbt_erase_shift); + numblocks = (int)(this->chipsize >> this->bbt_erase_shift); /* Full device write or specific chip ? */ if (chipsel == -1) { nrchips = this->numchips; @@ -443,7 +603,7 @@ static int write_bbt (struct mtd_info *mtd, uint8_t *buf, chip = chipsel; } } else { - numblocks = (int) (mtd->size >> this->bbt_erase_shift); + numblocks = (int)(mtd->size >> this->bbt_erase_shift); nrchips = 1; } @@ -472,27 +632,38 @@ static int write_bbt (struct mtd_info *mtd, uint8_t *buf, for (i = 0; i < td->maxblocks; i++) { int block = startblock + dir * i; /* Check, if the block is bad */ - switch ((this->bbt[block >> 2] >> (2 * (block & 0x03))) & 0x03) { + switch ((this->bbt[block >> 2] >> + (2 * (block & 0x03))) & 0x03) { case 0x01: case 0x03: continue; } - page = block << (this->bbt_erase_shift - this->page_shift); + page = block << + (this->bbt_erase_shift - this->page_shift); /* Check, if the block is used by the mirror table */ if (!md || md->pages[chip] != page) goto write; } - printk (KERN_ERR "No space left to write bad block table\n"); + printk(KERN_ERR "No space left to write bad block table\n"); return -ENOSPC; -write: + write: /* Set up shift count and masks for the flash table */ bits = td->options & NAND_BBT_NRBITS_MSK; + msk[2] = ~rcode; switch (bits) { - case 1: sft = 3; sftmsk = 0x07; msk[0] = 0x00; msk[1] = 0x01; msk[2] = ~rcode; msk[3] = 0x01; break; - case 2: sft = 2; sftmsk = 0x06; msk[0] = 0x00; msk[1] = 0x01; msk[2] = ~rcode; msk[3] = 0x03; break; - case 4: sft = 1; sftmsk = 0x04; msk[0] = 0x00; msk[1] = 0x0C; msk[2] = ~rcode; msk[3] = 0x0f; break; - case 8: sft = 0; sftmsk = 0x00; msk[0] = 0x00; msk[1] = 0x0F; msk[2] = ~rcode; msk[3] = 0xff; break; + case 1: sft = 3; sftmsk = 0x07; msk[0] = 0x00; msk[1] = 0x01; + msk[3] = 0x01; + break; + case 2: sft = 2; sftmsk = 0x06; msk[0] = 0x00; msk[1] = 0x01; + msk[3] = 0x03; + break; + case 4: sft = 1; sftmsk = 0x04; msk[0] = 0x00; msk[1] = 0x0C; + msk[3] = 0x0f; + break; + case 8: sft = 0; sftmsk = 0x00; msk[0] = 0x00; msk[1] = 0x0F; + msk[3] = 0xff; + break; default: return -EINVAL; } @@ -500,82 +671,92 @@ write: to = ((loff_t) page) << this->page_shift; - memcpy (&oobinfo, this->autooob, sizeof(oobinfo)); - oobinfo.useecc = MTD_NANDECC_PLACEONLY; - /* Must we save the block contents ? */ if (td->options & NAND_BBT_SAVECONTENT) { /* Make it block aligned */ to &= ~((loff_t) ((1 << this->bbt_erase_shift) - 1)); len = 1 << this->bbt_erase_shift; - res = mtd->read_ecc (mtd, to, len, &retlen, buf, &buf[len], &oobinfo); + res = mtd->read(mtd, to, len, &retlen, buf); if (res < 0) { if (retlen != len) { - printk (KERN_INFO "nand_bbt: Error reading block for writing the bad block table\n"); + printk(KERN_INFO "nand_bbt: Error " + "reading block for writing " + "the bad block table\n"); return res; } - printk (KERN_WARNING "nand_bbt: ECC error while reading block for writing bad block table\n"); + printk(KERN_WARNING "nand_bbt: ECC error " + "while reading block for writing " + "bad block table\n"); } + /* Read oob data */ + ops.ooblen = (len >> this->page_shift) * mtd->oobsize; + ops.oobbuf = &buf[len]; + res = mtd->read_oob(mtd, to + mtd->writesize, &ops); + if (res < 0 || ops.oobretlen != ops.ooblen) + goto outerr; + /* Calc the byte offset in the buffer */ pageoffs = page - (int)(to >> this->page_shift); offs = pageoffs << this->page_shift; /* Preset the bbt area with 0xff */ - memset (&buf[offs], 0xff, (size_t)(numblocks >> sft)); - /* Preset the bbt's oob area with 0xff */ - memset (&buf[len + pageoffs * mtd->oobsize], 0xff, - ((len >> this->page_shift) - pageoffs) * mtd->oobsize); - if (td->options & NAND_BBT_VERSION) { - buf[len + (pageoffs * mtd->oobsize) + td->veroffs] = td->version[chip]; - } + memset(&buf[offs], 0xff, (size_t) (numblocks >> sft)); + ooboffs = len + (pageoffs * mtd->oobsize); + } else { /* Calc length */ len = (size_t) (numblocks >> sft); /* Make it page aligned ! */ - len = (len + (mtd->oobblock-1)) & ~(mtd->oobblock-1); + len = (len + (mtd->writesize - 1)) & + ~(mtd->writesize - 1); /* Preset the buffer with 0xff */ - memset (buf, 0xff, len + (len >> this->page_shift) * mtd->oobsize); + memset(buf, 0xff, len + + (len >> this->page_shift)* mtd->oobsize); offs = 0; + ooboffs = len; /* Pattern is located in oob area of first page */ - memcpy (&buf[len + td->offs], td->pattern, td->len); - if (td->options & NAND_BBT_VERSION) { - buf[len + td->veroffs] = td->version[chip]; - } + memcpy(&buf[ooboffs + td->offs], td->pattern, td->len); } + if (td->options & NAND_BBT_VERSION) + buf[ooboffs + td->veroffs] = td->version[chip]; + /* walk through the memory table */ - for (i = 0; i < numblocks; ) { + for (i = 0; i < numblocks;) { uint8_t dat; dat = this->bbt[bbtoffs + (i >> 2)]; - for (j = 0; j < 4; j++ , i++) { + for (j = 0; j < 4; j++, i++) { int sftcnt = (i << (3 - sft)) & sftmsk; /* Do not store the reserved bbt blocks ! */ - buf[offs + (i >> sft)] &= ~(msk[dat & 0x03] << sftcnt); + buf[offs + (i >> sft)] &= + ~(msk[dat & 0x03] << sftcnt); dat >>= 2; } } - memset (&einfo, 0, sizeof (einfo)); + memset(&einfo, 0, sizeof(einfo)); einfo.mtd = mtd; - einfo.addr = (unsigned long) to; + einfo.addr = (unsigned long)to; einfo.len = 1 << this->bbt_erase_shift; - res = nand_erase_nand (mtd, &einfo, 1); - if (res < 0) { - printk (KERN_WARNING "nand_bbt: Error during block erase: %d\n", res); - return res; - } + res = nand_erase_nand(mtd, &einfo, 1); + if (res < 0) + goto outerr; - res = mtd->write_ecc (mtd, to, len, &retlen, buf, &buf[len], &oobinfo); - if (res < 0) { - printk (KERN_WARNING "nand_bbt: Error while writing bad block table %d\n", res); - return res; - } - printk (KERN_DEBUG "Bad block table written to 0x%08x, version 0x%02X\n", - (unsigned int) to, td->version[chip]); + res = scan_write_bbt(mtd, to, len, buf, &buf[len]); + if (res < 0) + goto outerr; + + printk(KERN_DEBUG "Bad block table written to 0x%08x, version " + "0x%02X\n", (unsigned int)to, td->version[chip]); /* Mark it as used */ td->pages[chip] = page; } return 0; + + outerr: + printk(KERN_WARNING + "nand_bbt: Error while writing bad block table %d\n", res); + return res; } /** @@ -586,29 +767,27 @@ write: * The function creates a memory based bbt by scanning the device * for manufacturer / software marked good / bad blocks */ -static int nand_memory_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd) +static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd) { struct nand_chip *this = mtd->priv; - /* Ensure that we only scan for the pattern and nothing else */ - bd->options = 0; - create_bbt (mtd, this->data_buf, bd, -1); - return 0; + bd->options &= ~NAND_BBT_SCANEMPTY; + return create_bbt(mtd, this->buffers->databuf, bd, -1); } /** - * check_create - [GENERIC] create and write bbt(s) if neccecary + * check_create - [GENERIC] create and write bbt(s) if necessary * @mtd: MTD device structure * @buf: temporary buffer * @bd: descriptor for the good/bad block search pattern * * The function checks the results of the previous call to read_bbt - * and creates / updates the bbt(s) if neccecary - * Creation is neccecary if no bbt was found for the chip/device - * Update is neccecary if one of the tables is missing or the + * and creates / updates the bbt(s) if necessary + * Creation is necessary if no bbt was found for the chip/device + * Update is necessary if one of the tables is missing or the * version nr. of one table is less than the other */ -static int check_create (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd) +static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd) { int i, chips, writeops, chipsel, res; struct nand_chip *this = mtd->priv; @@ -676,35 +855,35 @@ static int check_create (struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_des rd = td; goto writecheck; } -create: + create: /* Create the bad block table by scanning the device ? */ if (!(td->options & NAND_BBT_CREATE)) continue; /* Create the table in memory by scanning the chip(s) */ - create_bbt (mtd, buf, bd, chipsel); + create_bbt(mtd, buf, bd, chipsel); td->version[i] = 1; if (md) md->version[i] = 1; -writecheck: + writecheck: /* read back first ? */ if (rd) - read_abs_bbt (mtd, buf, rd, chipsel); + read_abs_bbt(mtd, buf, rd, chipsel); /* If they weren't versioned, read both. */ if (rd2) - read_abs_bbt (mtd, buf, rd2, chipsel); + read_abs_bbt(mtd, buf, rd2, chipsel); /* Write the bad block table to the device ? */ if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) { - res = write_bbt (mtd, buf, td, md, chipsel); + res = write_bbt(mtd, buf, td, md, chipsel); if (res < 0) return res; } /* Write the mirror bad block table to the device ? */ if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) { - res = write_bbt (mtd, buf, md, td, chipsel); + res = write_bbt(mtd, buf, md, td, chipsel); if (res < 0) return res; } @@ -721,7 +900,7 @@ writecheck: * accidental erasures / writes. The regions are identified by * the mark 0x02. */ -static void mark_bbt_region (struct mtd_info *mtd, struct nand_bbt_descr *td) +static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td) { struct nand_chip *this = mtd->priv; int i, j, chips, block, nrblocks, update; @@ -739,7 +918,8 @@ static void mark_bbt_region (struct mtd_info *mtd, struct nand_bbt_descr *td) for (i = 0; i < chips; i++) { if ((td->options & NAND_BBT_ABSPAGE) || !(td->options & NAND_BBT_WRITE)) { - if (td->pages[i] == -1) continue; + if (td->pages[i] == -1) + continue; block = td->pages[i] >> (this->bbt_erase_shift - this->page_shift); block <<= 1; oldval = this->bbt[(block >> 3)]; @@ -759,7 +939,8 @@ static void mark_bbt_region (struct mtd_info *mtd, struct nand_bbt_descr *td) oldval = this->bbt[(block >> 3)]; newval = oldval | (0x2 << (block & 0x06)); this->bbt[(block >> 3)] = newval; - if (oldval != newval) update = 1; + if (oldval != newval) + update = 1; block += 2; } /* If we want reserved blocks to be recorded to flash, and some @@ -784,7 +965,7 @@ static void mark_bbt_region (struct mtd_info *mtd, struct nand_bbt_descr *td) * by calling the nand_free_bbt function. * */ -int nand_scan_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd) +int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd) { struct nand_chip *this = mtd->priv; int len, res = 0; @@ -793,53 +974,56 @@ int nand_scan_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd) struct nand_bbt_descr *md = this->bbt_md; len = mtd->size >> (this->bbt_erase_shift + 2); - /* Allocate memory (2bit per block) */ - this->bbt = kmalloc (len, GFP_KERNEL); + /* Allocate memory (2bit per block) and clear the memory bad block table */ + this->bbt = kzalloc(len, GFP_KERNEL); if (!this->bbt) { - printk (KERN_ERR "nand_scan_bbt: Out of memory\n"); + printk(KERN_ERR "nand_scan_bbt: Out of memory\n"); return -ENOMEM; } - /* Clear the memory bad block table */ - memset (this->bbt, 0x00, len); /* If no primary table decriptor is given, scan the device * to build a memory based bad block table */ - if (!td) - return nand_memory_bbt(mtd, bd); + if (!td) { + if ((res = nand_memory_bbt(mtd, bd))) { + printk(KERN_ERR "nand_bbt: Can't scan flash and build the RAM-based BBT\n"); + kfree(this->bbt); + this->bbt = NULL; + } + return res; + } /* Allocate a temporary buffer for one eraseblock incl. oob */ len = (1 << this->bbt_erase_shift); len += (len >> this->page_shift) * mtd->oobsize; - buf = kmalloc (len, GFP_KERNEL); + buf = vmalloc(len); if (!buf) { - printk (KERN_ERR "nand_bbt: Out of memory\n"); - kfree (this->bbt); + printk(KERN_ERR "nand_bbt: Out of memory\n"); + kfree(this->bbt); this->bbt = NULL; return -ENOMEM; } /* Is the bbt at a given page ? */ if (td->options & NAND_BBT_ABSPAGE) { - res = read_abs_bbts (mtd, buf, td, md); + res = read_abs_bbts(mtd, buf, td, md); } else { /* Search the bad block table using a pattern in oob */ - res = search_read_bbts (mtd, buf, td, md); + res = search_read_bbts(mtd, buf, td, md); } if (res) - res = check_create (mtd, buf, bd); + res = check_create(mtd, buf, bd); /* Prevent the bbt regions from erasing / writing */ - mark_bbt_region (mtd, td); + mark_bbt_region(mtd, td); if (md) - mark_bbt_region (mtd, md); + mark_bbt_region(mtd, md); - kfree (buf); + vfree(buf); return res; } - /** * nand_update_bbt - [NAND Interface] update bad block table(s) * @mtd: MTD device structure @@ -847,7 +1031,7 @@ int nand_scan_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd) * * The function updates the bad block table(s) */ -int nand_update_bbt (struct mtd_info *mtd, loff_t offs) +int nand_update_bbt(struct mtd_info *mtd, loff_t offs) { struct nand_chip *this = mtd->priv; int len, res = 0, writeops = 0; @@ -863,9 +1047,9 @@ int nand_update_bbt (struct mtd_info *mtd, loff_t offs) /* Allocate a temporary buffer for one eraseblock incl. oob */ len = (1 << this->bbt_erase_shift); len += (len >> this->page_shift) * mtd->oobsize; - buf = kmalloc (len, GFP_KERNEL); + buf = kmalloc(len, GFP_KERNEL); if (!buf) { - printk (KERN_ERR "nand_update_bbt: Out of memory\n"); + printk(KERN_ERR "nand_update_bbt: Out of memory\n"); return -ENOMEM; } @@ -873,7 +1057,7 @@ int nand_update_bbt (struct mtd_info *mtd, loff_t offs) /* Do we have a bbt per chip ? */ if (td->options & NAND_BBT_PERCHIP) { - chip = (int) (offs >> this->chip_shift); + chip = (int)(offs >> this->chip_shift); chipsel = chip; } else { chip = 0; @@ -886,29 +1070,26 @@ int nand_update_bbt (struct mtd_info *mtd, loff_t offs) /* Write the bad block table to the device ? */ if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) { - res = write_bbt (mtd, buf, td, md, chipsel); + res = write_bbt(mtd, buf, td, md, chipsel); if (res < 0) goto out; } /* Write the mirror bad block table to the device ? */ if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) { - res = write_bbt (mtd, buf, md, td, chipsel); + res = write_bbt(mtd, buf, md, td, chipsel); } -out: - kfree (buf); + out: + kfree(buf); return res; } /* Define some generic bad / good block scan pattern which are used - * while scanning a device for factory marked good / bad blocks - * - * The memory based patterns just - */ + * while scanning a device for factory marked good / bad blocks. */ static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; static struct nand_bbt_descr smallpage_memorybased = { - .options = 0, + .options = NAND_BBT_SCAN2NDPAGE, .offs = 5, .len = 1, .pattern = scan_ff_pattern @@ -922,14 +1103,14 @@ static struct nand_bbt_descr largepage_memorybased = { }; static struct nand_bbt_descr smallpage_flashbased = { - .options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES, + .options = NAND_BBT_SCAN2NDPAGE, .offs = 5, .len = 1, .pattern = scan_ff_pattern }; static struct nand_bbt_descr largepage_flashbased = { - .options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES, + .options = NAND_BBT_SCAN2NDPAGE, .offs = 0, .len = 2, .pattern = scan_ff_pattern @@ -977,7 +1158,7 @@ static struct nand_bbt_descr bbt_mirror_descr = { * support for the device and calls the nand_scan_bbt function * */ -int nand_default_bbt (struct mtd_info *mtd) +int nand_default_bbt(struct mtd_info *mtd) { struct nand_chip *this = mtd->priv; @@ -987,7 +1168,7 @@ int nand_default_bbt (struct mtd_info *mtd) * of the good / bad information, so we _must_ store * this information in a good / bad table during * startup - */ + */ if (this->options & NAND_IS_AND) { /* Use the default pattern descriptors */ if (!this->bbt_td) { @@ -995,10 +1176,9 @@ int nand_default_bbt (struct mtd_info *mtd) this->bbt_md = &bbt_mirror_descr; } this->options |= NAND_USE_FLASH_BBT; - return nand_scan_bbt (mtd, &agand_flashbased); + return nand_scan_bbt(mtd, &agand_flashbased); } - /* Is a flash based bad block table requested ? */ if (this->options & NAND_USE_FLASH_BBT) { /* Use the default pattern descriptors */ @@ -1007,18 +1187,17 @@ int nand_default_bbt (struct mtd_info *mtd) this->bbt_md = &bbt_mirror_descr; } if (!this->badblock_pattern) { - this->badblock_pattern = (mtd->oobblock > 512) ? - &largepage_flashbased : &smallpage_flashbased; + this->badblock_pattern = (mtd->writesize > 512) ? &largepage_flashbased : &smallpage_flashbased; } } else { this->bbt_td = NULL; this->bbt_md = NULL; if (!this->badblock_pattern) { - this->badblock_pattern = (mtd->oobblock > 512) ? - &largepage_memorybased : &smallpage_memorybased; + this->badblock_pattern = (mtd->writesize > 512) ? + &largepage_memorybased : &smallpage_memorybased; } } - return nand_scan_bbt (mtd, this->badblock_pattern); + return nand_scan_bbt(mtd, this->badblock_pattern); } /** @@ -1027,26 +1206,35 @@ int nand_default_bbt (struct mtd_info *mtd) * @offs: offset in the device * @allowbbt: allow access to bad block table region * - */ -int nand_isbad_bbt (struct mtd_info *mtd, loff_t offs, int allowbbt) +*/ +int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt) { struct nand_chip *this = mtd->priv; int block; - uint8_t res; + uint8_t res; /* Get block number * 2 */ - block = (int) (offs >> (this->bbt_erase_shift - 1)); + block = (int)(offs >> (this->bbt_erase_shift - 1)); res = (this->bbt[block >> 3] >> (block & 0x06)) & 0x03; MTDDEBUG (MTD_DEBUG_LEVEL2, "nand_isbad_bbt(): bbt info for offs 0x%08x: " "(block %d) 0x%02x\n", (unsigned int)offs, res, block >> 1); switch ((int)res) { - case 0x00: return 0; - case 0x01: return 1; - case 0x02: return allowbbt ? 0 : 1; + case 0x00: + return 0; + case 0x01: + return 1; + case 0x02: + return allowbbt ? 0 : 1; } return 1; } +/* XXX U-BOOT XXX */ +#if 0 +EXPORT_SYMBOL(nand_scan_bbt); +EXPORT_SYMBOL(nand_default_bbt); +#endif + #endif diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/nand_ecc.c index 4c532b0794..e1d5154db2 100644 --- a/drivers/mtd/nand/nand_ecc.c +++ b/drivers/mtd/nand/nand_ecc.c @@ -7,7 +7,9 @@ * Copyright (C) 2000-2004 Steven J. Hill (sjhill@realitydiluted.com) * Toshiba America Electronics Components, Inc. * - * $Id: nand_ecc.c,v 1.14 2004/06/16 15:34:37 gleixner Exp $ + * Copyright (C) 2006 Thomas Gleixner + * + * $Id: nand_ecc.c,v 1.15 2005/11/07 11:14:30 gleixner Exp $ * * This file is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the @@ -39,6 +41,14 @@ #if defined(CONFIG_CMD_NAND) && !defined(CFG_NAND_LEGACY) +/* XXX U-BOOT XXX */ +#if 0 +#include +#include +#include +#include +#endif + #include /* @@ -128,6 +138,10 @@ int nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, return 0; } +/* XXX U-BOOT XXX */ +#if 0 +EXPORT_SYMBOL(nand_calculate_ecc); +#endif #endif /* CONFIG_NAND_SPL */ static inline int countbits(uint32_t byte) @@ -197,4 +211,9 @@ int nand_correct_data(struct mtd_info *mtd, u_char *dat, return -1; } +/* XXX U-BOOT XXX */ +#if 0 +EXPORT_SYMBOL(nand_correct_data); +#endif + #endif diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/nand_ids.c index 7363490395..f8b96cf025 100644 --- a/drivers/mtd/nand/nand_ids.c +++ b/drivers/mtd/nand/nand_ids.c @@ -2,8 +2,8 @@ * drivers/mtd/nandids.c * * Copyright (C) 2002 Thomas Gleixner (tglx@linutronix.de) - * - * $Id: nand_ids.c,v 1.10 2004/05/26 13:40:12 gleixner Exp $ + * + * $Id: nand_ids.c,v 1.16 2005/11/07 11:14:31 gleixner Exp $ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -16,7 +16,6 @@ #if defined(CONFIG_CMD_NAND) && !defined(CFG_NAND_LEGACY) #include - /* * Chip ID list * @@ -29,13 +28,15 @@ * 512 512 Byte page size */ struct nand_flash_dev nand_flash_ids[] = { + +#ifdef CONFIG_MTD_NAND_MUSEUM_IDS {"NAND 1MiB 5V 8-bit", 0x6e, 256, 1, 0x1000, 0}, {"NAND 2MiB 5V 8-bit", 0x64, 256, 2, 0x1000, 0}, {"NAND 4MiB 5V 8-bit", 0x6b, 512, 4, 0x2000, 0}, {"NAND 1MiB 3,3V 8-bit", 0xe8, 256, 1, 0x1000, 0}, {"NAND 1MiB 3,3V 8-bit", 0xec, 256, 1, 0x1000, 0}, {"NAND 2MiB 3,3V 8-bit", 0xea, 256, 2, 0x1000, 0}, - {"NAND 4MiB 3,3V 8-bit", 0xd5, 512, 4, 0x2000, 0}, + {"NAND 4MiB 3,3V 8-bit", 0xd5, 512, 4, 0x2000, 0}, {"NAND 4MiB 3,3V 8-bit", 0xe3, 512, 4, 0x2000, 0}, {"NAND 4MiB 3,3V 8-bit", 0xe5, 512, 4, 0x2000, 0}, {"NAND 8MiB 3,3V 8-bit", 0xd6, 512, 8, 0x2000, 0}, @@ -44,6 +45,7 @@ struct nand_flash_dev nand_flash_ids[] = { {"NAND 8MiB 3,3V 8-bit", 0xe6, 512, 8, 0x2000, 0}, {"NAND 8MiB 1,8V 16-bit", 0x49, 512, 8, 0x2000, NAND_BUSWIDTH_16}, {"NAND 8MiB 3,3V 16-bit", 0x59, 512, 8, 0x2000, NAND_BUSWIDTH_16}, +#endif {"NAND 16MiB 1,8V 8-bit", 0x33, 512, 16, 0x4000, 0}, {"NAND 16MiB 3,3V 8-bit", 0x73, 512, 16, 0x4000, 0}, @@ -61,52 +63,72 @@ struct nand_flash_dev nand_flash_ids[] = { {"NAND 64MiB 3,3V 16-bit", 0x56, 512, 64, 0x4000, NAND_BUSWIDTH_16}, {"NAND 128MiB 1,8V 8-bit", 0x78, 512, 128, 0x4000, 0}, + {"NAND 128MiB 1,8V 8-bit", 0x39, 512, 128, 0x4000, 0}, {"NAND 128MiB 3,3V 8-bit", 0x79, 512, 128, 0x4000, 0}, {"NAND 128MiB 1,8V 16-bit", 0x72, 512, 128, 0x4000, NAND_BUSWIDTH_16}, + {"NAND 128MiB 1,8V 16-bit", 0x49, 512, 128, 0x4000, NAND_BUSWIDTH_16}, {"NAND 128MiB 3,3V 16-bit", 0x74, 512, 128, 0x4000, NAND_BUSWIDTH_16}, + {"NAND 128MiB 3,3V 16-bit", 0x59, 512, 128, 0x4000, NAND_BUSWIDTH_16}, {"NAND 256MiB 3,3V 8-bit", 0x71, 512, 256, 0x4000, 0}, - /* These are the new chips with large page size. The pagesize - * and the erasesize is determined from the extended id bytes - */ + /* + * These are the new chips with large page size. The pagesize and the + * erasesize is determined from the extended id bytes + */ +#define LP_OPTIONS (NAND_SAMSUNG_LP_OPTIONS | NAND_NO_READRDY | NAND_NO_AUTOINCR) +#define LP_OPTIONS16 (LP_OPTIONS | NAND_BUSWIDTH_16) + + /*512 Megabit */ + {"NAND 64MiB 1,8V 8-bit", 0xA2, 0, 64, 0, LP_OPTIONS}, + {"NAND 64MiB 3,3V 8-bit", 0xF2, 0, 64, 0, LP_OPTIONS}, + {"NAND 64MiB 1,8V 16-bit", 0xB2, 0, 64, 0, LP_OPTIONS16}, + {"NAND 64MiB 3,3V 16-bit", 0xC2, 0, 64, 0, LP_OPTIONS16}, + /* 1 Gigabit */ - {"NAND 128MiB 1,8V 8-bit", 0xA1, 0, 128, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 128MiB 3,3V 8-bit", 0xF1, 0, 128, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 128MiB 1,8V 16-bit", 0xB1, 0, 128, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, - {"NAND 128MiB 3,3V 16-bit", 0xC1, 0, 128, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, + {"NAND 128MiB 1,8V 8-bit", 0xA1, 0, 128, 0, LP_OPTIONS}, + {"NAND 128MiB 3,3V 8-bit", 0xF1, 0, 128, 0, LP_OPTIONS}, + {"NAND 128MiB 1,8V 16-bit", 0xB1, 0, 128, 0, LP_OPTIONS16}, + {"NAND 128MiB 3,3V 16-bit", 0xC1, 0, 128, 0, LP_OPTIONS16}, /* 2 Gigabit */ - {"NAND 256MiB 1,8V 8-bit", 0xAA, 0, 256, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 256MiB 3,3V 8-bit", 0xDA, 0, 256, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 256MiB 1,8V 16-bit", 0xBA, 0, 256, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, - {"NAND 256MiB 3,3V 16-bit", 0xCA, 0, 256, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, + {"NAND 256MiB 1,8V 8-bit", 0xAA, 0, 256, 0, LP_OPTIONS}, + {"NAND 256MiB 3,3V 8-bit", 0xDA, 0, 256, 0, LP_OPTIONS}, + {"NAND 256MiB 1,8V 16-bit", 0xBA, 0, 256, 0, LP_OPTIONS16}, + {"NAND 256MiB 3,3V 16-bit", 0xCA, 0, 256, 0, LP_OPTIONS16}, /* 4 Gigabit */ - {"NAND 512MiB 1,8V 8-bit", 0xAC, 0, 512, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 512MiB 3,3V 8-bit", 0xDC, 0, 512, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 512MiB 1,8V 16-bit", 0xBC, 0, 512, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, - {"NAND 512MiB 3,3V 16-bit", 0xCC, 0, 512, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, + {"NAND 512MiB 1,8V 8-bit", 0xAC, 0, 512, 0, LP_OPTIONS}, + {"NAND 512MiB 3,3V 8-bit", 0xDC, 0, 512, 0, LP_OPTIONS}, + {"NAND 512MiB 1,8V 16-bit", 0xBC, 0, 512, 0, LP_OPTIONS16}, + {"NAND 512MiB 3,3V 16-bit", 0xCC, 0, 512, 0, LP_OPTIONS16}, /* 8 Gigabit */ - {"NAND 1GiB 1,8V 8-bit", 0xA3, 0, 1024, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 1GiB 3,3V 8-bit", 0xD3, 0, 1024, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 1GiB 1,8V 16-bit", 0xB3, 0, 1024, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, - {"NAND 1GiB 3,3V 16-bit", 0xC3, 0, 1024, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, + {"NAND 1GiB 1,8V 8-bit", 0xA3, 0, 1024, 0, LP_OPTIONS}, + {"NAND 1GiB 3,3V 8-bit", 0xD3, 0, 1024, 0, LP_OPTIONS}, + {"NAND 1GiB 1,8V 16-bit", 0xB3, 0, 1024, 0, LP_OPTIONS16}, + {"NAND 1GiB 3,3V 16-bit", 0xC3, 0, 1024, 0, LP_OPTIONS16}, /* 16 Gigabit */ - {"NAND 2GiB 1,8V 8-bit", 0xA5, 0, 2048, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 2GiB 3,3V 8-bit", 0xD5, 0, 2048, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_NO_AUTOINCR}, - {"NAND 2GiB 1,8V 16-bit", 0xB5, 0, 2048, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, - {"NAND 2GiB 3,3V 16-bit", 0xC5, 0, 2048, 0, NAND_SAMSUNG_LP_OPTIONS | NAND_BUSWIDTH_16 | NAND_NO_AUTOINCR}, - - /* Renesas AND 1 Gigabit. Those chips do not support extended id and have a strange page/block layout ! - * The chosen minimum erasesize is 4 * 2 * 2048 = 16384 Byte, as those chips have an array of 4 page planes - * 1 block = 2 pages, but due to plane arrangement the blocks 0-3 consists of page 0 + 4,1 + 5, 2 + 6, 3 + 7 - * Anyway JFFS2 would increase the eraseblock size so we chose a combined one which can be erased in one go - * There are more speed improvements for reads and writes possible, but not implemented now + {"NAND 2GiB 1,8V 8-bit", 0xA5, 0, 2048, 0, LP_OPTIONS}, + {"NAND 2GiB 3,3V 8-bit", 0xD5, 0, 2048, 0, LP_OPTIONS}, + {"NAND 2GiB 1,8V 16-bit", 0xB5, 0, 2048, 0, LP_OPTIONS16}, + {"NAND 2GiB 3,3V 16-bit", 0xC5, 0, 2048, 0, LP_OPTIONS16}, + + /* + * Renesas AND 1 Gigabit. Those chips do not support extended id and + * have a strange page/block layout ! The chosen minimum erasesize is + * 4 * 2 * 2048 = 16384 Byte, as those chips have an array of 4 page + * planes 1 block = 2 pages, but due to plane arrangement the blocks + * 0-3 consists of page 0 + 4,1 + 5, 2 + 6, 3 + 7 Anyway JFFS2 would + * increase the eraseblock size so we chose a combined one which can be + * erased in one go There are more speed improvements for reads and + * writes possible, but not implemented now */ - {"AND 128MiB 3,3V 8-bit", 0x01, 2048, 128, 0x4000, NAND_IS_AND | NAND_NO_AUTOINCR | NAND_4PAGE_ARRAY}, + {"AND 128MiB 3,3V 8-bit", 0x01, 2048, 128, 0x4000, + NAND_IS_AND | NAND_NO_AUTOINCR |NAND_NO_READRDY | NAND_4PAGE_ARRAY | + BBT_AUTO_REFRESH + }, {NULL,} }; @@ -121,6 +143,7 @@ struct nand_manufacturers nand_manuf_ids[] = { {NAND_MFR_NATIONAL, "National"}, {NAND_MFR_RENESAS, "Renesas"}, {NAND_MFR_STMICRO, "ST Micro"}, + {NAND_MFR_HYNIX, "Hynix"}, {NAND_MFR_MICRON, "Micron"}, {0x0, "Unknown"} }; diff --git a/drivers/mtd/nand/nand_util.c b/drivers/mtd/nand/nand_util.c index 828cc338ad..78e70cc807 100644 --- a/drivers/mtd/nand/nand_util.c +++ b/drivers/mtd/nand/nand_util.c @@ -39,6 +39,9 @@ #include #include + +#include +#include #include #include @@ -69,71 +72,33 @@ static int nand_block_bad_scrub(struct mtd_info *mtd, loff_t ofs, int getchip) int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) { struct jffs2_unknown_node cleanmarker; - int clmpos = 0; - int clmlen = 8; erase_info_t erase; ulong erase_length; - int isNAND; int bbtest = 1; int result; int percent_complete = -1; int (*nand_block_bad_old)(struct mtd_info *, loff_t, int) = NULL; const char *mtd_device = meminfo->name; + struct mtd_oob_ops oob_opts; + struct nand_chip *chip = meminfo->priv; + uint8_t buf[64]; + memset(buf, 0, sizeof(buf)); memset(&erase, 0, sizeof(erase)); + memset(&oob_opts, 0, sizeof(oob_opts)); erase.mtd = meminfo; erase.len = meminfo->erasesize; erase.addr = opts->offset; erase_length = opts->length; - isNAND = meminfo->type == MTD_NANDFLASH ? 1 : 0; - if (opts->jffs2) { - cleanmarker.magic = cpu_to_je16 (JFFS2_MAGIC_BITMASK); - cleanmarker.nodetype = cpu_to_je16 (JFFS2_NODETYPE_CLEANMARKER); - if (isNAND) { - struct nand_oobinfo *oobinfo = &meminfo->oobinfo; - - /* check for autoplacement */ - if (oobinfo->useecc == MTD_NANDECC_AUTOPLACE) { - /* get the position of the free bytes */ - if (!oobinfo->oobfree[0][1]) { - printf(" Eeep. Autoplacement selected " - "and no empty space in oob\n"); - return -1; - } - clmpos = oobinfo->oobfree[0][0]; - clmlen = oobinfo->oobfree[0][1]; - if (clmlen > 8) - clmlen = 8; - } else { - /* legacy mode */ - switch (meminfo->oobsize) { - case 8: - clmpos = 6; - clmlen = 2; - break; - case 16: - clmpos = 8; - clmlen = 8; - break; - case 64: - clmpos = 16; - clmlen = 8; - break; - } - } - - cleanmarker.totlen = cpu_to_je32(8); - } else { - cleanmarker.totlen = - cpu_to_je32(sizeof(struct jffs2_unknown_node)); - } - cleanmarker.hdr_crc = cpu_to_je32( - crc32_no_comp(0, (unsigned char *) &cleanmarker, - sizeof(struct jffs2_unknown_node) - 4)); - } + cleanmarker.magic = cpu_to_je16 (JFFS2_MAGIC_BITMASK); + cleanmarker.nodetype = cpu_to_je16 (JFFS2_NODETYPE_CLEANMARKER); + cleanmarker.totlen = cpu_to_je32(8); + cleanmarker.hdr_crc = cpu_to_je32( + crc32_no_comp(0, (unsigned char *) &cleanmarker, + sizeof(struct jffs2_unknown_node) - 4)); /* scrub option allows to erase badblock. To prevent internal * check from erase() method, set block check method to dummy @@ -163,7 +128,7 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) for (; erase.addr < opts->offset + erase_length; erase.addr += meminfo->erasesize) { - + WATCHDOG_RESET (); if (!opts->scrub && bbtest) { @@ -194,25 +159,21 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) /* format for JFFS2 ? */ if (opts->jffs2) { - /* write cleanmarker */ - if (isNAND) { - size_t written; - result = meminfo->write_oob(meminfo, - erase.addr + clmpos, - clmlen, - &written, - (unsigned char *) - &cleanmarker); - if (result != 0) { - printf("\n%s: MTD writeoob failure: %d\n", - mtd_device, result); - continue; - } - } else { - printf("\n%s: this erase routine only supports" - " NAND devices!\n", - mtd_device); + chip->ops.len = chip->ops.ooblen = 64; + chip->ops.datbuf = NULL; + chip->ops.oobbuf = buf; + chip->ops.ooboffs = chip->badblockpos & ~0x01; + + result = meminfo->write_oob(meminfo, + erase.addr + meminfo->oobsize, + &chip->ops); + if (result != 0) { + printf("\n%s: MTD writeoob failure: %d\n", + mtd_device, result); + continue; } + else + printf("%s: MTD writeoob at 0x%08x\n",mtd_device, erase.addr + meminfo->oobsize ); } if (!opts->quiet) { @@ -232,11 +193,11 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) percent_complete = percent; printf("\rErasing at 0x%x -- %3d%% complete.", - erase.addr, percent); + erase.addr, percent); if (opts->jffs2 && result == 0) - printf(" Cleanmarker written at 0x%x.", - erase.addr); + printf(" Cleanmarker written at 0x%x.", + erase.addr); } } } @@ -253,6 +214,9 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) return 0; } +/* XXX U-BOOT XXX */ +#if 0 + #define MAX_PAGE_SIZE 2048 #define MAX_OOB_SIZE 64 @@ -263,26 +227,189 @@ static unsigned char data_buf[MAX_PAGE_SIZE]; static unsigned char oob_buf[MAX_OOB_SIZE]; /* OOB layouts to pass into the kernel as default */ -static struct nand_oobinfo none_oobinfo = { +static struct nand_ecclayout none_ecclayout = { .useecc = MTD_NANDECC_OFF, }; -static struct nand_oobinfo jffs2_oobinfo = { +static struct nand_ecclayout jffs2_ecclayout = { .useecc = MTD_NANDECC_PLACE, .eccbytes = 6, .eccpos = { 0, 1, 2, 3, 6, 7 } }; -static struct nand_oobinfo yaffs_oobinfo = { +static struct nand_ecclayout yaffs_ecclayout = { .useecc = MTD_NANDECC_PLACE, .eccbytes = 6, .eccpos = { 8, 9, 10, 13, 14, 15} }; -static struct nand_oobinfo autoplace_oobinfo = { +static struct nand_ecclayout autoplace_ecclayout = { .useecc = MTD_NANDECC_AUTOPLACE }; +#endif + +/** + * nand_fill_oob - [Internal] Transfer client buffer to oob + * @chip: nand chip structure + * @oob: oob data buffer + * @ops: oob ops structure + * + * Copied from nand_base.c + */ +static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, + struct mtd_oob_ops *ops) +{ + size_t len = ops->ooblen; + + switch(ops->mode) { + + case MTD_OOB_PLACE: + case MTD_OOB_RAW: + memcpy(chip->oob_poi + ops->ooboffs, oob, len); + return oob + len; + + case MTD_OOB_AUTO: { + struct nand_oobfree *free = chip->ecc.layout->oobfree; + uint32_t boffs = 0, woffs = ops->ooboffs; + size_t bytes = 0; + + for(; free->length && len; free++, len -= bytes) { + /* Write request not from offset 0 ? */ + if (unlikely(woffs)) { + if (woffs >= free->length) { + woffs -= free->length; + continue; + } + boffs = free->offset + woffs; + bytes = min_t(size_t, len, + (free->length - woffs)); + woffs = 0; + } else { + bytes = min_t(size_t, len, free->length); + boffs = free->offset; + } + memcpy(chip->oob_poi + boffs, oob, bytes); + oob += bytes; + } + return oob; + } + default: + BUG(); + } + return NULL; +} + +#define NOTALIGNED(x) (x & (chip->subpagesize - 1)) != 0 + + +/* copied from nand_base.c: nand_do_write_ops() + * Only very small changes + */ +int nand_write_opts(nand_info_t *mtd, loff_t to, mtd_oob_ops_t *ops) +{ + int chipnr, realpage, page, blockmask, column; + struct nand_chip *chip = mtd->priv; + uint32_t writelen = ops->len; + uint8_t *oob = ops->oobbuf; + uint8_t *buf = ops->datbuf; + int ret, subpage; + + ops->retlen = 0; + if (!writelen) + return 0; + + printk("nand_write_opts: to: 0x%08x, ops->len: 0x%08x\n", to, ops->len); + + /* reject writes, which are not page aligned */ + if (NOTALIGNED(to) || NOTALIGNED(ops->len)) { + printk(KERN_NOTICE "nand_write: " + "Attempt to write not page aligned data\n"); + return -EINVAL; + } + + column = to & (mtd->writesize - 1); + subpage = column || (writelen & (mtd->writesize - 1)); + + if (subpage && oob) { + printk(KERN_NOTICE "nand_write: " + "Attempt to write oob to subpage\n"); + return -EINVAL; + } + + chipnr = (int)(to >> chip->chip_shift); + chip->select_chip(mtd, chipnr); + + /* XXX U-BOOT XXX */ +#if 0 + /* Check, if it is write protected */ + if (nand_check_wp(mtd)) + return -EIO; +#endif + + realpage = (int)(to >> chip->page_shift); + page = realpage & chip->pagemask; + blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; + + /* Invalidate the page cache, when we write to the cached page */ + if (to <= (chip->pagebuf << chip->page_shift) && + (chip->pagebuf << chip->page_shift) < (to + ops->len)) + chip->pagebuf = -1; + + /* If we're not given explicit OOB data, let it be 0xFF */ + if (likely(!oob)) { + printf("!oob, writing %d bytes with 0xff to chip->oob_poi (0x%08x)\n", mtd->oobsize, chip->oob_poi); + memset(chip->oob_poi, 0xff, mtd->oobsize); + } + + while(1) { + int bytes = mtd->writesize; + int cached = writelen > bytes && page != blockmask; + uint8_t *wbuf = buf; + + /* Partial page write ? */ + if (unlikely(column || writelen < (mtd->writesize - 1))) { + cached = 0; + bytes = min_t(int, bytes - column, (int) writelen); + chip->pagebuf = -1; + memset(chip->buffers->databuf, 0xff, mtd->writesize); + memcpy(&chip->buffers->databuf[column], buf, bytes); + wbuf = chip->buffers->databuf; + } + + if (unlikely(oob)) + oob = nand_fill_oob(chip, oob, ops); + + ret = chip->write_page(mtd, chip, wbuf, page, cached, + (ops->mode == MTD_OOB_RAW)); + if (ret) + break; + + writelen -= bytes; + if (!writelen) + break; + + column = 0; + buf += bytes; + realpage++; + + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + } + } + + ops->retlen = ops->len - writelen; + if (unlikely(oob)) + ops->oobretlen = ops->ooblen; + return ret; +} + +/* XXX U-BOOT XXX */ +#if 0 /** * nand_write_opts: - write image to NAND flash with support for various options * @@ -301,9 +428,9 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) int blockstart = -1; loff_t offs; int readlen; - int oobinfochanged = 0; + int ecclayoutchanged = 0; int percent_complete = -1; - struct nand_oobinfo old_oobinfo; + struct nand_ecclayout old_ecclayout; ulong mtdoffset = opts->offset; ulong erasesize_blockalign; u_char *buffer = opts->buffer; @@ -324,35 +451,35 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) } /* make sure device page sizes are valid */ - if (!(meminfo->oobsize == 16 && meminfo->oobblock == 512) - && !(meminfo->oobsize == 8 && meminfo->oobblock == 256) - && !(meminfo->oobsize == 64 && meminfo->oobblock == 2048)) { + if (!(meminfo->oobsize == 16 && meminfo->writesize == 512) + && !(meminfo->oobsize == 8 && meminfo->writesize == 256) + && !(meminfo->oobsize == 64 && meminfo->writesize == 2048)) { printf("Unknown flash (not normal NAND)\n"); return -1; } /* read the current oob info */ - memcpy(&old_oobinfo, &meminfo->oobinfo, sizeof(old_oobinfo)); + memcpy(&old_ecclayout, &meminfo->ecclayout, sizeof(old_ecclayout)); /* write without ecc? */ if (opts->noecc) { - memcpy(&meminfo->oobinfo, &none_oobinfo, - sizeof(meminfo->oobinfo)); - oobinfochanged = 1; + memcpy(&meminfo->ecclayout, &none_ecclayout, + sizeof(meminfo->ecclayout)); + ecclayoutchanged = 1; } /* autoplace ECC? */ - if (opts->autoplace && (old_oobinfo.useecc != MTD_NANDECC_AUTOPLACE)) { + if (opts->autoplace && (old_ecclayout.useecc != MTD_NANDECC_AUTOPLACE)) { - memcpy(&meminfo->oobinfo, &autoplace_oobinfo, - sizeof(meminfo->oobinfo)); - oobinfochanged = 1; + memcpy(&meminfo->ecclayout, &autoplace_ecclayout, + sizeof(meminfo->ecclayout)); + ecclayoutchanged = 1; } /* force OOB layout for jffs2 or yaffs? */ if (opts->forcejffs2 || opts->forceyaffs) { - struct nand_oobinfo *oobsel = - opts->forcejffs2 ? &jffs2_oobinfo : &yaffs_oobinfo; + struct nand_ecclayout *oobsel = + opts->forcejffs2 ? &jffs2_ecclayout : &yaffs_ecclayout; if (meminfo->oobsize == 8) { if (opts->forceyaffs) { @@ -361,15 +488,15 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) goto restoreoob; } /* Adjust number of ecc bytes */ - jffs2_oobinfo.eccbytes = 3; + jffs2_ecclayout.eccbytes = 3; } - memcpy(&meminfo->oobinfo, oobsel, sizeof(meminfo->oobinfo)); + memcpy(&meminfo->ecclayout, oobsel, sizeof(meminfo->ecclayout)); } /* get image length */ imglen = opts->length; - pagelen = meminfo->oobblock + pagelen = meminfo->writesize + ((opts->writeoob != 0) ? meminfo->oobsize : 0); /* check, if file is pagealigned */ @@ -379,11 +506,11 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) } /* check, if length fits into device */ - if (((imglen / pagelen) * meminfo->oobblock) + if (((imglen / pagelen) * meminfo->writesize) > (meminfo->size - opts->offset)) { printf("Image %d bytes, NAND page %d bytes, " "OOB area %u bytes, device size %u bytes\n", - imglen, pagelen, meminfo->oobblock, meminfo->size); + imglen, pagelen, meminfo->writesize, meminfo->size); printf("Input block does not fit into device\n"); goto restoreoob; } @@ -437,11 +564,11 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) } while (offs < blockstart + erasesize_blockalign); } - readlen = meminfo->oobblock; + readlen = meminfo->writesize; if (opts->pad && (imglen < readlen)) { readlen = imglen; memset(data_buf + readlen, 0xff, - meminfo->oobblock - readlen); + meminfo->writesize - readlen); } /* read page data from input memory buffer */ @@ -474,7 +601,7 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) /* write out the page data */ result = meminfo->write(meminfo, mtdoffset, - meminfo->oobblock, + meminfo->writesize, &written, (unsigned char *) &data_buf); @@ -505,16 +632,16 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) } } - mtdoffset += meminfo->oobblock; + mtdoffset += meminfo->writesize; } if (!opts->quiet) printf("\n"); restoreoob: - if (oobinfochanged) { - memcpy(&meminfo->oobinfo, &old_oobinfo, - sizeof(meminfo->oobinfo)); + if (ecclayoutchanged) { + memcpy(&meminfo->ecclayout, &old_ecclayout, + sizeof(meminfo->ecclayout)); } if (imglen > 0) { @@ -548,22 +675,22 @@ int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts) int result; /* make sure device page sizes are valid */ - if (!(meminfo->oobsize == 16 && meminfo->oobblock == 512) - && !(meminfo->oobsize == 8 && meminfo->oobblock == 256) - && !(meminfo->oobsize == 64 && meminfo->oobblock == 2048)) { + if (!(meminfo->oobsize == 16 && meminfo->writesize == 512) + && !(meminfo->oobsize == 8 && meminfo->writesize == 256) + && !(meminfo->oobsize == 64 && meminfo->writesize == 2048)) { printf("Unknown flash (not normal NAND)\n"); return -1; } - pagelen = meminfo->oobblock + pagelen = meminfo->writesize + ((opts->readoob != 0) ? meminfo->oobsize : 0); /* check, if length is not larger than device */ - if (((imglen / pagelen) * meminfo->oobblock) + if (((imglen / pagelen) * meminfo->writesize) > (meminfo->size - opts->offset)) { printf("Image %d bytes, NAND page %d bytes, " "OOB area %u bytes, device size %u bytes\n", - imglen, pagelen, meminfo->oobblock, meminfo->size); + imglen, pagelen, meminfo->writesize, meminfo->size); printf("Input block is larger than device\n"); return -1; } @@ -621,7 +748,7 @@ int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts) /* read page data to memory buffer */ result = meminfo->read(meminfo, mtdoffset, - meminfo->oobblock, + meminfo->writesize, &readlen, (unsigned char *) &data_buf); @@ -685,7 +812,7 @@ int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts) } } - mtdoffset += meminfo->oobblock; + mtdoffset += meminfo->writesize; } if (!opts->quiet) @@ -699,7 +826,10 @@ int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts) /* return happy */ return 0; } +#endif +/* XXX U-BOOT XXX */ +#if 0 /****************************************************************************** * Support for locking / unlocking operations of some NAND devices *****************************************************************************/ @@ -784,7 +914,7 @@ int nand_get_lock_status(nand_info_t *meminfo, ulong offset) this->select_chip(meminfo, chipnr); - if ((offset & (meminfo->oobblock - 1)) != 0) { + if ((offset & (meminfo->writesize - 1)) != 0) { printf ("nand_get_lock_status: " "Start address must be beginning of " "nand page!\n"); @@ -813,7 +943,7 @@ int nand_get_lock_status(nand_info_t *meminfo, ulong offset) * @param meminfo nand mtd instance * @param start start byte address * @param length number of bytes to unlock (must be a multiple of - * page size nand->oobblock) + * page size nand->writesize) * * @return 0 on success, -1 in case of error */ @@ -839,14 +969,14 @@ int nand_unlock(nand_info_t *meminfo, ulong start, ulong length) goto out; } - if ((start & (meminfo->oobblock - 1)) != 0) { + if ((start & (meminfo->writesize - 1)) != 0) { printf ("nand_unlock: Start address must be beginning of " "nand page!\n"); ret = -1; goto out; } - if (length == 0 || (length & (meminfo->oobblock - 1)) != 0) { + if (length == 0 || (length & (meminfo->writesize - 1)) != 0) { printf ("nand_unlock: Length must be a multiple of nand page " "size!\n"); ret = -1; @@ -875,5 +1005,6 @@ int nand_unlock(nand_info_t *meminfo, ulong start, ulong length) this->select_chip(meminfo, -1); return ret; } +#endif #endif diff --git a/include/common.h b/include/common.h index 2fcb1fd379..06ed27806f 100644 --- a/include/common.h +++ b/include/common.h @@ -119,11 +119,13 @@ typedef volatile unsigned char vu_char; #define debugX(level,fmt,args...) #endif /* DEBUG */ +#ifndef BUG #define BUG() do { \ printf("BUG: failure at %s:%d/%s()!\n", __FILE__, __LINE__, __FUNCTION__); \ panic("BUG!"); \ } while (0) #define BUG_ON(condition) do { if (unlikely((condition)!=0)) BUG(); } while(0) +#endif /* BUG */ typedef void (interrupt_handler_t)(void *); diff --git a/include/linux/err.h b/include/linux/err.h new file mode 100644 index 0000000000..4e08c4fe68 --- /dev/null +++ b/include/linux/err.h @@ -0,0 +1,45 @@ +#ifndef _LINUX_ERR_H +#define _LINUX_ERR_H + +/* XXX U-BOOT XXX */ +#if 0 +#include +#else +#include +#endif + +#include + + +/* + * Kernel pointers have redundant information, so we can use a + * scheme where we can return either an error code or a dentry + * pointer with the same return value. + * + * This should be a per-architecture thing, to allow different + * error and pointer decisions. + */ +#define MAX_ERRNO 4095 + +#ifndef __ASSEMBLY__ + +#define IS_ERR_VALUE(x) unlikely((x) >= (unsigned long)-MAX_ERRNO) + +static inline void *ERR_PTR(long error) +{ + return (void *) error; +} + +static inline long PTR_ERR(const void *ptr) +{ + return (long) ptr; +} + +static inline long IS_ERR(const void *ptr) +{ + return IS_ERR_VALUE((unsigned long)ptr); +} + +#endif + +#endif /* _LINUX_ERR_H */ diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h new file mode 100644 index 0000000000..d1ded51d7c --- /dev/null +++ b/include/linux/mtd/blktrans.h @@ -0,0 +1,81 @@ +/* + * $Id: blktrans.h,v 1.6 2005/11/07 11:14:54 gleixner Exp $ + * + * (C) 2003 David Woodhouse + * + * Interface to Linux block layer for MTD 'translation layers'. + * + */ + +#ifndef __MTD_TRANS_H__ +#define __MTD_TRANS_H__ + +/* XXX U-BOOT XXX */ +#if 0 +#include +#else +#include +#endif + +struct hd_geometry; +struct mtd_info; +struct mtd_blktrans_ops; +struct file; +struct inode; + +struct mtd_blktrans_dev { + struct mtd_blktrans_ops *tr; + struct list_head list; + struct mtd_info *mtd; +/* XXX U-BOOT XXX */ +#if 0 + struct mutex lock; +#endif + int devnum; + unsigned long size; + int readonly; + void *blkcore_priv; /* gendisk in 2.5, devfs_handle in 2.4 */ +}; + +struct blkcore_priv; /* Differs for 2.4 and 2.5 kernels; private */ + +struct mtd_blktrans_ops { + char *name; + int major; + int part_bits; + int blksize; + int blkshift; + + /* Access functions */ + int (*readsect)(struct mtd_blktrans_dev *dev, + unsigned long block, char *buffer); + int (*writesect)(struct mtd_blktrans_dev *dev, + unsigned long block, char *buffer); + + /* Block layer ioctls */ + int (*getgeo)(struct mtd_blktrans_dev *dev, struct hd_geometry *geo); + int (*flush)(struct mtd_blktrans_dev *dev); + + /* Called with mtd_table_mutex held; no race with add/remove */ + int (*open)(struct mtd_blktrans_dev *dev); + int (*release)(struct mtd_blktrans_dev *dev); + + /* Called on {de,}registration and on subsequent addition/removal + of devices, with mtd_table_mutex held. */ + void (*add_mtd)(struct mtd_blktrans_ops *tr, struct mtd_info *mtd); + void (*remove_dev)(struct mtd_blktrans_dev *dev); + + struct list_head devs; + struct list_head list; + struct module *owner; + + struct mtd_blkcore_priv *blkcore_priv; +}; + +extern int register_mtd_blktrans(struct mtd_blktrans_ops *tr); +extern int deregister_mtd_blktrans(struct mtd_blktrans_ops *tr); +extern int add_mtd_blktrans_dev(struct mtd_blktrans_dev *dev); +extern int del_mtd_blktrans_dev(struct mtd_blktrans_dev *dev); + + +#endif /* __MTD_TRANS_H__ */ diff --git a/include/linux/mtd/compat.h b/include/linux/mtd/compat.h index fe55087ea9..86a6e43ca9 100644 --- a/include/linux/mtd/compat.h +++ b/include/linux/mtd/compat.h @@ -18,7 +18,12 @@ #define KERN_DEBUG #define kmalloc(size, flags) malloc(size) -#define kfree(ptr) free(ptr) +#define kzalloc(size, flags) calloc(size, 1) +#define vmalloc(size) malloc(size) +#define kfree(ptr) free(ptr) +#define vfree(ptr) free(ptr) + +#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c)) /* * ..and if you can't take the strict diff --git a/include/linux/mtd/doc2000.h b/include/linux/mtd/doc2000.h index 29f6767865..12de2845a3 100644 --- a/include/linux/mtd/doc2000.h +++ b/include/linux/mtd/doc2000.h @@ -1,15 +1,23 @@ - -/* Linux driver for Disk-On-Chip 2000 */ -/* (c) 1999 Machine Vision Holdings, Inc. */ -/* Author: David Woodhouse */ -/* $Id: doc2000.h,v 1.15 2001/09/19 00:22:15 dwmw2 Exp $ */ +/* + * Linux driver for Disk-On-Chip devices + * + * Copyright (C) 1999 Machine Vision Holdings, Inc. + * Copyright (C) 2001-2003 David Woodhouse + * Copyright (C) 2002-2003 Greg Ungerer + * Copyright (C) 2002-2003 SnapGear Inc + * + * $Id: doc2000.h,v 1.25 2005/11/07 11:14:54 gleixner Exp $ + * + * Released under GPL + */ #ifndef __MTD_DOC2000_H__ #define __MTD_DOC2000_H__ -struct DiskOnChip; - -#include +#include +#if 0 +#include +#endif #define DoC_Sig1 0 #define DoC_Sig2 1 @@ -40,10 +48,58 @@ struct DiskOnChip; #define DoC_Mil_CDSN_IO 0x0800 #define DoC_2k_CDSN_IO 0x1800 -#define ReadDOC_(adr, reg) ((volatile unsigned char)(*(volatile __u8 *)(((unsigned long)adr)+((reg))))) -#define WriteDOC_(d, adr, reg) do{ *(volatile __u8 *)(((unsigned long)adr)+((reg))) = (__u8)d; eieio();} while(0) - -#define DOC_IOREMAP_LEN 0x4000 +#define DoC_Mplus_NOP 0x1002 +#define DoC_Mplus_AliasResolution 0x1004 +#define DoC_Mplus_DOCControl 0x1006 +#define DoC_Mplus_AccessStatus 0x1008 +#define DoC_Mplus_DeviceSelect 0x1008 +#define DoC_Mplus_Configuration 0x100a +#define DoC_Mplus_OutputControl 0x100c +#define DoC_Mplus_FlashControl 0x1020 +#define DoC_Mplus_FlashSelect 0x1022 +#define DoC_Mplus_FlashCmd 0x1024 +#define DoC_Mplus_FlashAddress 0x1026 +#define DoC_Mplus_FlashData0 0x1028 +#define DoC_Mplus_FlashData1 0x1029 +#define DoC_Mplus_ReadPipeInit 0x102a +#define DoC_Mplus_LastDataRead 0x102c +#define DoC_Mplus_LastDataRead1 0x102d +#define DoC_Mplus_WritePipeTerm 0x102e +#define DoC_Mplus_ECCSyndrome0 0x1040 +#define DoC_Mplus_ECCSyndrome1 0x1041 +#define DoC_Mplus_ECCSyndrome2 0x1042 +#define DoC_Mplus_ECCSyndrome3 0x1043 +#define DoC_Mplus_ECCSyndrome4 0x1044 +#define DoC_Mplus_ECCSyndrome5 0x1045 +#define DoC_Mplus_ECCConf 0x1046 +#define DoC_Mplus_Toggle 0x1046 +#define DoC_Mplus_DownloadStatus 0x1074 +#define DoC_Mplus_CtrlConfirm 0x1076 +#define DoC_Mplus_Power 0x1fff + +/* How to access the device? + * On ARM, it'll be mmap'd directly with 32-bit wide accesses. + * On PPC, it's mmap'd and 16-bit wide. + * Others use readb/writeb + */ +#if defined(__arm__) +#define ReadDOC_(adr, reg) ((unsigned char)(*(volatile __u32 *)(((unsigned long)adr)+((reg)<<2)))) +#define WriteDOC_(d, adr, reg) do{ *(volatile __u32 *)(((unsigned long)adr)+((reg)<<2)) = (__u32)d; wmb();} while(0) +#define DOC_IOREMAP_LEN 0x8000 +#elif defined(__ppc__) +#define ReadDOC_(adr, reg) ((unsigned char)(*(volatile __u16 *)(((unsigned long)adr)+((reg)<<1)))) +#define WriteDOC_(d, adr, reg) do{ *(volatile __u16 *)(((unsigned long)adr)+((reg)<<1)) = (__u16)d; wmb();} while(0) +#define DOC_IOREMAP_LEN 0x4000 +#else +#define ReadDOC_(adr, reg) readb((void __iomem *)(adr) + (reg)) +#define WriteDOC_(d, adr, reg) writeb(d, (void __iomem *)(adr) + (reg)) +#define DOC_IOREMAP_LEN 0x2000 + +#endif + +#if defined(__i386__) || defined(__x86_64__) +#define USE_MEMCPY +#endif /* These are provided to directly use the DoC_xxx defines */ #define ReadDOC(adr, reg) ReadDOC_(adr,DoC_##reg) @@ -54,14 +110,21 @@ struct DiskOnChip; #define DOC_MODE_RESERVED1 2 #define DOC_MODE_RESERVED2 3 -#define DOC_MODE_MDWREN 4 #define DOC_MODE_CLR_ERR 0x80 +#define DOC_MODE_RST_LAT 0x10 +#define DOC_MODE_BDECT 0x08 +#define DOC_MODE_MDWREN 0x04 -#define DOC_ChipID_UNKNOWN 0x00 #define DOC_ChipID_Doc2k 0x20 +#define DOC_ChipID_Doc2kTSOP 0x21 /* internal number for MTD */ #define DOC_ChipID_DocMil 0x30 +#define DOC_ChipID_DocMilPlus32 0x40 +#define DOC_ChipID_DocMilPlus16 0x41 #define CDSN_CTRL_FR_B 0x80 +#define CDSN_CTRL_FR_B0 0x40 +#define CDSN_CTRL_FR_B1 0x80 + #define CDSN_CTRL_ECC_IO 0x20 #define CDSN_CTRL_FLASH_IO 0x10 #define CDSN_CTRL_WP 0x08 @@ -77,41 +140,47 @@ struct DiskOnChip; #define DOC_ECC_RESV 0x02 #define DOC_ECC_IGNORE 0x01 +#define DOC_FLASH_CE 0x80 +#define DOC_FLASH_WP 0x40 +#define DOC_FLASH_BANK 0x02 + /* We have to also set the reserved bit 1 for enable */ #define DOC_ECC_EN (DOC_ECC__EN | DOC_ECC_RESV) #define DOC_ECC_DIS (DOC_ECC_RESV) +struct Nand { + char floor, chip; + unsigned long curadr; + unsigned char curmode; + /* Also some erase/write/pipeline info when we get that far */ +}; + #define MAX_FLOORS 4 #define MAX_CHIPS 4 -#define MAX_FLOORS_MIL 4 +#define MAX_FLOORS_MIL 1 #define MAX_CHIPS_MIL 1 +#define MAX_FLOORS_MPLUS 2 +#define MAX_CHIPS_MPLUS 1 + #define ADDR_COLUMN 1 #define ADDR_PAGE 2 #define ADDR_COLUMN_PAGE 3 -struct Nand { - char floor, chip; - unsigned long curadr; - unsigned char curmode; - /* Also some erase/write/pipeline info when we get that far */ -}; - struct DiskOnChip { unsigned long physadr; - unsigned long virtadr; + void __iomem *virtadr; unsigned long totlen; - char* name; - char ChipID; /* Type of DiskOnChip */ + unsigned char ChipID; /* Type of DiskOnChip */ int ioreg; - char* chips_name; unsigned long mfr; /* Flash IDs - only one type of flash per device */ unsigned long id; int chipshift; char page256; char pageadrlen; + char interleave; /* Internal interleaving - Millennium Plus style */ unsigned long erasesize; int curfloor; @@ -119,98 +188,22 @@ struct DiskOnChip { int numchips; struct Nand *chips; - - int nftl_found; - struct NFTLrecord nftl; + struct mtd_info *nextdoc; +/* XXX U-BOOT XXX */ +#if 0 + struct mutex lock; +#endif }; -#define SECTORSIZE 512 - -/* Return codes from doc_write(), doc_read(), and doc_erase(). - */ -#define DOC_OK 0 -#define DOC_EIO 1 -#define DOC_EINVAL 2 -#define DOC_EECC 3 -#define DOC_ETIMEOUT 4 - -/* - * Function Prototypes - */ int doc_decode_ecc(unsigned char sector[512], unsigned char ecc1[6]); -int doc_rw(struct DiskOnChip* this, int cmd, loff_t from, size_t len, - size_t *retlen, u_char *buf); -int doc_read_ecc(struct DiskOnChip* this, loff_t from, size_t len, - size_t *retlen, u_char *buf, u_char *eccbuf); -int doc_write_ecc(struct DiskOnChip* this, loff_t to, size_t len, - size_t *retlen, const u_char *buf, u_char *eccbuf); -int doc_read_oob(struct DiskOnChip* this, loff_t ofs, size_t len, - size_t *retlen, u_char *buf); -int doc_write_oob(struct DiskOnChip* this, loff_t ofs, size_t len, - size_t *retlen, const u_char *buf); -int doc_erase (struct DiskOnChip* this, loff_t ofs, size_t len); - -void doc_probe(unsigned long physadr); - -void doc_print(struct DiskOnChip*); - -/* - * Standard NAND flash commands - */ -#define NAND_CMD_READ0 0 -#define NAND_CMD_READ1 1 -#define NAND_CMD_PAGEPROG 0x10 -#define NAND_CMD_READOOB 0x50 -#define NAND_CMD_ERASE1 0x60 -#define NAND_CMD_STATUS 0x70 -#define NAND_CMD_SEQIN 0x80 -#define NAND_CMD_READID 0x90 -#define NAND_CMD_ERASE2 0xd0 -#define NAND_CMD_RESET 0xff - +/* XXX U-BOOT XXX */ +#if 1 /* * NAND Flash Manufacturer ID Codes */ -#define NAND_MFR_TOSHIBA 0x98 -#define NAND_MFR_SAMSUNG 0xec - -/* - * NAND Flash Device ID Structure - * - * Structure overview: - * - * name - Complete name of device - * - * manufacture_id - manufacturer ID code of device. - * - * model_id - model ID code of device. - * - * chipshift - total number of address bits for the device which - * is used to calculate address offsets and the total - * number of bytes the device is capable of. - * - * page256 - denotes if flash device has 256 byte pages or not. - * - * pageadrlen - number of bytes minus one needed to hold the - * complete address into the flash array. Keep in - * mind that when a read or write is done to a - * specific address, the address is input serially - * 8 bits at a time. This structure member is used - * by the read/write routines as a loop index for - * shifting the address out 8 bits at a time. - * - * erasesize - size of an erase block in the flash device. - */ -struct nand_flash_dev { - char * name; - int manufacture_id; - int model_id; - int chipshift; - char page256; - char pageadrlen; - unsigned long erasesize; - int bus16; -}; +#define NAND_MFR_TOSHIBA 0x98 +#define NAND_MFR_SAMSUNG 0xec +#endif #endif /* __MTD_DOC2000_H__ */ diff --git a/include/linux/mtd/inftl-user.h b/include/linux/mtd/inftl-user.h new file mode 100644 index 0000000000..9b1e2526b4 --- /dev/null +++ b/include/linux/mtd/inftl-user.h @@ -0,0 +1,91 @@ +/* + * $Id: inftl-user.h,v 1.2 2005/11/07 11:14:56 gleixner Exp $ + * + * Parts of INFTL headers shared with userspace + * + */ + +#ifndef __MTD_INFTL_USER_H__ +#define __MTD_INFTL_USER_H__ + +#define OSAK_VERSION 0x5120 +#define PERCENTUSED 98 + +#define SECTORSIZE 512 + +/* Block Control Information */ + +struct inftl_bci { + uint8_t ECCsig[6]; + uint8_t Status; + uint8_t Status1; +} __attribute__((packed)); + +struct inftl_unithead1 { + uint16_t virtualUnitNo; + uint16_t prevUnitNo; + uint8_t ANAC; + uint8_t NACs; + uint8_t parityPerField; + uint8_t discarded; +} __attribute__((packed)); + +struct inftl_unithead2 { + uint8_t parityPerField; + uint8_t ANAC; + uint16_t prevUnitNo; + uint16_t virtualUnitNo; + uint8_t NACs; + uint8_t discarded; +} __attribute__((packed)); + +struct inftl_unittail { + uint8_t Reserved[4]; + uint16_t EraseMark; + uint16_t EraseMark1; +} __attribute__((packed)); + +union inftl_uci { + struct inftl_unithead1 a; + struct inftl_unithead2 b; + struct inftl_unittail c; +}; + +struct inftl_oob { + struct inftl_bci b; + union inftl_uci u; +}; + + +/* INFTL Media Header */ + +struct INFTLPartition { + __u32 virtualUnits; + __u32 firstUnit; + __u32 lastUnit; + __u32 flags; + __u32 spareUnits; + __u32 Reserved0; + __u32 Reserved1; +} __attribute__((packed)); + +struct INFTLMediaHeader { + char bootRecordID[8]; + __u32 NoOfBootImageBlocks; + __u32 NoOfBinaryPartitions; + __u32 NoOfBDTLPartitions; + __u32 BlockMultiplierBits; + __u32 FormatFlags; + __u32 OsakVersion; + __u32 PercentUsed; + struct INFTLPartition Partitions[4]; +} __attribute__((packed)); + +/* Partition flag types */ +#define INFTL_BINARY 0x20000000 +#define INFTL_BDTL 0x40000000 +#define INFTL_LAST 0x80000000 + +#endif /* __MTD_INFTL_USER_H__ */ + + diff --git a/include/linux/mtd/jffs2-user.h b/include/linux/mtd/jffs2-user.h new file mode 100644 index 0000000000..d508ef0ae0 --- /dev/null +++ b/include/linux/mtd/jffs2-user.h @@ -0,0 +1,35 @@ +/* + * $Id: jffs2-user.h,v 1.1 2004/05/05 11:57:54 dwmw2 Exp $ + * + * JFFS2 definitions for use in user space only + */ + +#ifndef __JFFS2_USER_H__ +#define __JFFS2_USER_H__ + +/* This file is blessed for inclusion by userspace */ +#include +#include +#include + +#undef cpu_to_je16 +#undef cpu_to_je32 +#undef cpu_to_jemode +#undef je16_to_cpu +#undef je32_to_cpu +#undef jemode_to_cpu + +extern int target_endian; + +#define t16(x) ({ uint16_t __b = (x); (target_endian==__BYTE_ORDER)?__b:bswap_16(__b); }) +#define t32(x) ({ uint32_t __b = (x); (target_endian==__BYTE_ORDER)?__b:bswap_32(__b); }) + +#define cpu_to_je16(x) ((jint16_t){t16(x)}) +#define cpu_to_je32(x) ((jint32_t){t32(x)}) +#define cpu_to_jemode(x) ((jmode_t){t32(x)}) + +#define je16_to_cpu(x) (t16((x).v16)) +#define je32_to_cpu(x) (t32((x).v32)) +#define jemode_to_cpu(x) (t32((x).m)) + +#endif /* __JFFS2_USER_H__ */ diff --git a/include/linux/mtd/mtd-abi.h b/include/linux/mtd/mtd-abi.h index 4cebea9597..0ce2099d69 100644 --- a/include/linux/mtd/mtd-abi.h +++ b/include/linux/mtd/mtd-abi.h @@ -1,5 +1,5 @@ /* - * $Id: mtd-abi.h,v 1.7 2004/11/23 15:37:32 gleixner Exp $ + * $Id: mtd-abi.h,v 1.13 2005/11/07 11:14:56 gleixner Exp $ * * Portions of MTD ABI definition which are shared by kernel and user space */ @@ -7,6 +7,10 @@ #ifndef __MTD_ABI_H__ #define __MTD_ABI_H__ +#if 1 +#include +#endif + struct erase_info_user { uint32_t start; uint32_t length; @@ -15,7 +19,7 @@ struct erase_info_user { struct mtd_oob_buf { uint32_t start; uint32_t length; - unsigned char *ptr; + unsigned char __user *ptr; }; #define MTD_ABSENT 0 @@ -23,47 +27,41 @@ struct mtd_oob_buf { #define MTD_ROM 2 #define MTD_NORFLASH 3 #define MTD_NANDFLASH 4 -#define MTD_PEROM 5 -#define MTD_OTHER 14 -#define MTD_UNKNOWN 15 - -#define MTD_CLEAR_BITS 1 /* Bits can be cleared (flash) */ -#define MTD_SET_BITS 2 /* Bits can be set */ -#define MTD_ERASEABLE 4 /* Has an erase function */ -#define MTD_WRITEB_WRITEABLE 8 /* Direct IO is possible */ -#define MTD_VOLATILE 16 /* Set for RAMs */ -#define MTD_XIP 32 /* eXecute-In-Place possible */ -#define MTD_OOB 64 /* Out-of-band data (NAND flash) */ -#define MTD_ECC 128 /* Device capable of automatic ECC */ -#define MTD_NO_VIRTBLOCKS 256 /* Virtual blocks not allowed */ - -/* Some common devices / combinations of capabilities */ -#define MTD_CAP_ROM 0 -#define MTD_CAP_RAM (MTD_CLEAR_BITS|MTD_SET_BITS|MTD_WRITEB_WRITEABLE) -#define MTD_CAP_NORFLASH (MTD_CLEAR_BITS|MTD_ERASEABLE) -#define MTD_CAP_NANDFLASH (MTD_CLEAR_BITS|MTD_ERASEABLE|MTD_OOB) -#define MTD_WRITEABLE (MTD_CLEAR_BITS|MTD_SET_BITS) +#define MTD_DATAFLASH 6 +#define MTD_UBIVOLUME 7 +#define MTD_WRITEABLE 0x400 /* Device is writeable */ +#define MTD_BIT_WRITEABLE 0x800 /* Single bits can be flipped */ +#define MTD_NO_ERASE 0x1000 /* No erase necessary */ +#define MTD_STUPID_LOCK 0x2000 /* Always locked after reset */ -/* Types of automatic ECC/Checksum available */ -#define MTD_ECC_NONE 0 /* No automatic ECC available */ -#define MTD_ECC_RS_DiskOnChip 1 /* Automatic ECC on DiskOnChip */ -#define MTD_ECC_SW 2 /* SW ECC for Toshiba & Samsung devices */ +// Some common devices / combinations of capabilities +#define MTD_CAP_ROM 0 +#define MTD_CAP_RAM (MTD_WRITEABLE | MTD_BIT_WRITEABLE | MTD_NO_ERASE) +#define MTD_CAP_NORFLASH (MTD_WRITEABLE | MTD_BIT_WRITEABLE) +#define MTD_CAP_NANDFLASH (MTD_WRITEABLE) /* ECC byte placement */ -#define MTD_NANDECC_OFF 0 /* Switch off ECC (Not recommended) */ -#define MTD_NANDECC_PLACE 1 /* Use the given placement in the structure (YAFFS1 legacy mode) */ -#define MTD_NANDECC_AUTOPLACE 2 /* Use the default placement scheme */ -#define MTD_NANDECC_PLACEONLY 3 /* Use the given placement in the structure (Do not store ecc result on read) */ -#define MTD_NANDECC_AUTOPL_USR 4 /* Use the given autoplacement scheme rather than using the default */ +#define MTD_NANDECC_OFF 0 // Switch off ECC (Not recommended) +#define MTD_NANDECC_PLACE 1 // Use the given placement in the structure (YAFFS1 legacy mode) +#define MTD_NANDECC_AUTOPLACE 2 // Use the default placement scheme +#define MTD_NANDECC_PLACEONLY 3 // Use the given placement in the structure (Do not store ecc result on read) +#define MTD_NANDECC_AUTOPL_USR 4 // Use the given autoplacement scheme rather than using the default + +/* OTP mode selection */ +#define MTD_OTP_OFF 0 +#define MTD_OTP_FACTORY 1 +#define MTD_OTP_USER 2 struct mtd_info_user { uint8_t type; uint32_t flags; - uint32_t size; /* Total size of the MTD */ + uint32_t size; // Total size of the MTD uint32_t erasesize; - uint32_t oobblock; /* Size of OOB blocks (e.g. 512) */ - uint32_t oobsize; /* Amount of OOB data per block (e.g. 16) */ + uint32_t writesize; + uint32_t oobsize; // Amount of OOB data per block (e.g. 16) + /* The below two fields are obsolete and broken, do not use them + * (TODO: remove at some point) */ uint32_t ecctype; uint32_t eccsize; }; @@ -76,19 +74,36 @@ struct region_info_user { uint32_t regionindex; }; -#define MEMGETINFO _IOR('M', 1, struct mtd_info_user) -#define MEMERASE _IOW('M', 2, struct erase_info_user) -#define MEMWRITEOOB _IOWR('M', 3, struct mtd_oob_buf) -#define MEMREADOOB _IOWR('M', 4, struct mtd_oob_buf) -#define MEMLOCK _IOW('M', 5, struct erase_info_user) -#define MEMUNLOCK _IOW('M', 6, struct erase_info_user) +struct otp_info { + uint32_t start; + uint32_t length; + uint32_t locked; +}; + +#define MEMGETINFO _IOR('M', 1, struct mtd_info_user) +#define MEMERASE _IOW('M', 2, struct erase_info_user) +#define MEMWRITEOOB _IOWR('M', 3, struct mtd_oob_buf) +#define MEMREADOOB _IOWR('M', 4, struct mtd_oob_buf) +#define MEMLOCK _IOW('M', 5, struct erase_info_user) +#define MEMUNLOCK _IOW('M', 6, struct erase_info_user) #define MEMGETREGIONCOUNT _IOR('M', 7, int) #define MEMGETREGIONINFO _IOWR('M', 8, struct region_info_user) #define MEMSETOOBSEL _IOW('M', 9, struct nand_oobinfo) #define MEMGETOOBSEL _IOR('M', 10, struct nand_oobinfo) #define MEMGETBADBLOCK _IOW('M', 11, loff_t) #define MEMSETBADBLOCK _IOW('M', 12, loff_t) +#define OTPSELECT _IOR('M', 13, int) +#define OTPGETREGIONCOUNT _IOW('M', 14, int) +#define OTPGETREGIONINFO _IOW('M', 15, struct otp_info) +#define OTPLOCK _IOR('M', 16, struct otp_info) +#define ECCGETLAYOUT _IOR('M', 17, struct nand_ecclayout) +#define ECCGETSTATS _IOR('M', 18, struct mtd_ecc_stats) +#define MTDFILEMODE _IO('M', 19) +/* + * Obsolete legacy interface. Keep it in order not to break userspace + * interfaces + */ struct nand_oobinfo { uint32_t useecc; uint32_t eccbytes; @@ -96,4 +111,46 @@ struct nand_oobinfo { uint32_t eccpos[48]; }; +struct nand_oobfree { + uint32_t offset; + uint32_t length; +}; + +#define MTD_MAX_OOBFREE_ENTRIES 8 +/* + * ECC layout control structure. Exported to userspace for + * diagnosis and to allow creation of raw images + */ +struct nand_ecclayout { + uint32_t eccbytes; + uint32_t eccpos[64]; + uint32_t oobavail; + struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES]; +}; + +/** + * struct mtd_ecc_stats - error correction stats + * + * @corrected: number of corrected bits + * @failed: number of uncorrectable errors + * @badblocks: number of bad blocks in this partition + * @bbtblocks: number of blocks reserved for bad block tables + */ +struct mtd_ecc_stats { + uint32_t corrected; + uint32_t failed; + uint32_t badblocks; + uint32_t bbtblocks; +}; + +/* + * Read/write file modes for access to MTD + */ +enum mtd_file_modes { + MTD_MODE_NORMAL = MTD_OTP_OFF, + MTD_MODE_OTP_FACTORY = MTD_OTP_FACTORY, + MTD_MODE_OTP_USER = MTD_OTP_USER, + MTD_MODE_RAW, +}; + #endif /* __MTD_ABI_H__ */ diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index 05ba375a82..8e0dc00f75 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -1,5 +1,5 @@ /* - * $Id: mtd.h,v 1.56 2004/08/09 18:46:04 dmarlin Exp $ + * $Id: mtd.h,v 1.61 2005/11/07 11:14:54 gleixner Exp $ * * Copyright (C) 1999-2003 David Woodhouse et al. * @@ -8,10 +8,13 @@ #ifndef __MTD_MTD_H__ #define __MTD_MTD_H__ + #include #include -#define MAX_MTD_DEVICES 16 +#define MTD_CHAR_MAJOR 90 +#define MTD_BLOCK_MAJOR 31 +#define MAX_MTD_DEVICES 32 #define MTD_ERASE_PENDING 0x01 #define MTD_ERASING 0x02 @@ -41,32 +44,83 @@ struct mtd_erase_region_info { u_int32_t offset; /* At which this region starts, from the beginning of the MTD */ u_int32_t erasesize; /* For this region */ u_int32_t numblocks; /* Number of blocks of erasesize in this region */ + unsigned long *lockmap; /* If keeping bitmap of locks */ +}; + +/* + * oob operation modes + * + * MTD_OOB_PLACE: oob data are placed at the given offset + * MTD_OOB_AUTO: oob data are automatically placed at the free areas + * which are defined by the ecclayout + * MTD_OOB_RAW: mode to read raw data+oob in one chunk. The oob data + * is inserted into the data. Thats a raw image of the + * flash contents. + */ +typedef enum { + MTD_OOB_PLACE, + MTD_OOB_AUTO, + MTD_OOB_RAW, +} mtd_oob_mode_t; + +/** + * struct mtd_oob_ops - oob operation operands + * @mode: operation mode + * + * @len: number of data bytes to write/read + * + * @retlen: number of data bytes written/read + * + * @ooblen: number of oob bytes to write/read + * @oobretlen: number of oob bytes written/read + * @ooboffs: offset of oob data in the oob area (only relevant when + * mode = MTD_OOB_PLACE) + * @datbuf: data buffer - if NULL only oob data are read/written + * @oobbuf: oob data buffer + * + * Note, it is allowed to read more then one OOB area at one go, but not write. + * The interface assumes that the OOB write requests program only one page's + * OOB area. + */ +struct mtd_oob_ops { + mtd_oob_mode_t mode; + size_t len; + size_t retlen; + size_t ooblen; + size_t oobretlen; + uint32_t ooboffs; + uint8_t *datbuf; + uint8_t *oobbuf; }; struct mtd_info { u_char type; u_int32_t flags; - u_int32_t size; /* Total size of the MTD */ + u_int32_t size; // Total size of the MTD - /* "Major" erase size for the device. Naïve users may take this + /* "Major" erase size for the device. Naïve users may take this * to be the only erase size available, or may use the more detailed * information below if they desire */ u_int32_t erasesize; + /* Minimal writable flash unit size. In case of NOR flash it is 1 (even + * though individual bits can be cleared), in case of NAND flash it is + * one NAND page (or half, or one-fourths of it), in case of ECC-ed NOR + * it is of ECC block size, etc. It is illegal to have writesize = 0. + * Any driver registering a struct mtd_info must ensure a writesize of + * 1 or larger. + */ + u_int32_t writesize; - u_int32_t oobblock; /* Size of OOB blocks (e.g. 512) */ - u_int32_t oobsize; /* Amount of OOB data per block (e.g. 16) */ - u_int32_t oobavail; /* Number of bytes in OOB area available for fs */ - u_int32_t ecctype; - u_int32_t eccsize; - + u_int32_t oobsize; // Amount of OOB data per block (e.g. 16) + u_int32_t oobavail; // Available OOB bytes per block - /* Kernel-only stuff starts here. */ + // Kernel-only stuff starts here. char *name; int index; - /* oobinfo is a nand_oobinfo structure, which can be set by iotcl (MEMSETOOBINFO) */ - struct nand_oobinfo oobinfo; + /* ecc layout structure pointer - read only ! */ + struct nand_ecclayout *ecclayout; /* Data for variable erase regions. If numeraseregions is zero, * it means that the whole device has erasesize as given above. @@ -74,9 +128,6 @@ struct mtd_info { int numeraseregions; struct mtd_erase_region_info *eraseregions; - /* This really shouldn't be here. It can go away in 2.5 */ - u_int32_t bank_size; - int (*erase) (struct mtd_info *mtd, struct erase_info *instr); /* This stuff for eXecute-In-Place */ @@ -89,39 +140,35 @@ struct mtd_info { int (*read) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf); int (*write) (struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf); - int (*read_ecc) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf, u_char *eccbuf, struct nand_oobinfo *oobsel); - int (*write_ecc) (struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf, u_char *eccbuf, struct nand_oobinfo *oobsel); - - int (*read_oob) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf); - int (*write_oob) (struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf); + int (*read_oob) (struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops); + int (*write_oob) (struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops); /* * Methods to access the protection register area, present in some * flash devices. The user data is one time programmable but the * factory data is read only. */ - int (*read_user_prot_reg) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf); - + int (*get_fact_prot_info) (struct mtd_info *mtd, struct otp_info *buf, size_t len); int (*read_fact_prot_reg) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf); - - /* This function is not yet implemented */ + int (*get_user_prot_info) (struct mtd_info *mtd, struct otp_info *buf, size_t len); + int (*read_user_prot_reg) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf); int (*write_user_prot_reg) (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf); + int (*lock_user_prot_reg) (struct mtd_info *mtd, loff_t from, size_t len); + +/* XXX U-BOOT XXX */ #if 0 - /* kvec-based read/write methods. We need these especially for NAND flash, - with its limited number of write cycles per erase. + /* kvec-based read/write methods. NB: The 'count' parameter is the number of _vectors_, each of which contains an (ofs, len) tuple. */ - int (*readv) (struct mtd_info *mtd, struct kvec *vecs, unsigned long count, loff_t from, size_t *retlen); - int (*readv_ecc) (struct mtd_info *mtd, struct kvec *vecs, unsigned long count, loff_t from, - size_t *retlen, u_char *eccbuf, struct nand_oobinfo *oobsel); int (*writev) (struct mtd_info *mtd, const struct kvec *vecs, unsigned long count, loff_t to, size_t *retlen); - int (*writev_ecc) (struct mtd_info *mtd, const struct kvec *vecs, unsigned long count, loff_t to, - size_t *retlen, u_char *eccbuf, struct nand_oobinfo *oobsel); #endif + /* Sync */ void (*sync) (struct mtd_info *mtd); -#if 0 + /* Chip-supported device locking */ int (*lock) (struct mtd_info *mtd, loff_t ofs, size_t len); int (*unlock) (struct mtd_info *mtd, loff_t ofs, size_t len); @@ -129,15 +176,32 @@ struct mtd_info { /* Power Management functions */ int (*suspend) (struct mtd_info *mtd); void (*resume) (struct mtd_info *mtd); -#endif + /* Bad block management functions */ int (*block_isbad) (struct mtd_info *mtd, loff_t ofs); int (*block_markbad) (struct mtd_info *mtd, loff_t ofs); +/* XXX U-BOOT XXX */ +#if 0 + struct notifier_block reboot_notifier; /* default mode before reboot */ +#endif + + /* ECC status information */ + struct mtd_ecc_stats ecc_stats; + /* Subpage shift (NAND) */ + int subpage_sft; + void *priv; struct module *owner; int usecount; + + /* If the driver is something smart, like UBI, it may need to maintain + * its own reference counting. The below functions are only for driver. + * The driver may register its callbacks. These callbacks are not + * supposed to be called by MTD users */ + int (*get_device) (struct mtd_info *mtd); + void (*put_device) (struct mtd_info *mtd); }; @@ -147,9 +211,11 @@ extern int add_mtd_device(struct mtd_info *mtd); extern int del_mtd_device (struct mtd_info *mtd); extern struct mtd_info *get_mtd_device(struct mtd_info *mtd, int num); +extern struct mtd_info *get_mtd_device_nm(const char *name); extern void put_mtd_device(struct mtd_info *mtd); +/* XXX U-BOOT XXX */ #if 0 struct mtd_notifier { void (*add)(struct mtd_info *mtd); @@ -157,7 +223,6 @@ struct mtd_notifier { struct list_head list; }; - extern void register_mtd_user (struct mtd_notifier *new); extern int unregister_mtd_user (struct mtd_notifier *old); @@ -168,20 +233,6 @@ int default_mtd_readv(struct mtd_info *mtd, struct kvec *vecs, unsigned long count, loff_t from, size_t *retlen); #endif -#define MTD_ERASE(mtd, args...) (*(mtd->erase))(mtd, args) -#define MTD_POINT(mtd, a,b,c,d) (*(mtd->point))(mtd, a,b,c, (u_char **)(d)) -#define MTD_UNPOINT(mtd, arg) (*(mtd->unpoint))(mtd, (u_char *)arg) -#define MTD_READ(mtd, args...) (*(mtd->read))(mtd, args) -#define MTD_WRITE(mtd, args...) (*(mtd->write))(mtd, args) -#define MTD_READV(mtd, args...) (*(mtd->readv))(mtd, args) -#define MTD_WRITEV(mtd, args...) (*(mtd->writev))(mtd, args) -#define MTD_READECC(mtd, args...) (*(mtd->read_ecc))(mtd, args) -#define MTD_WRITEECC(mtd, args...) (*(mtd->write_ecc))(mtd, args) -#define MTD_READOOB(mtd, args...) (*(mtd->read_oob))(mtd, args) -#define MTD_WRITEOOB(mtd, args...) (*(mtd->write_oob))(mtd, args) -#define MTD_SYNC(mtd) do { if (mtd->sync) (*(mtd->sync))(mtd); } while (0) - - #ifdef CONFIG_MTD_PARTITIONS void mtd_erase_callback(struct erase_info *instr); #else @@ -208,7 +259,6 @@ static inline void mtd_erase_callback(struct erase_info *instr) } while(0) #else /* CONFIG_MTD_DEBUG */ #define MTDDEBUG(n, args...) do { } while(0) - #endif /* CONFIG_MTD_DEBUG */ #endif /* __MTD_MTD_H__ */ diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index e2a25a60d8..db8bd7ba22 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -2,114 +2,123 @@ * linux/include/linux/mtd/nand.h * * Copyright (c) 2000 David Woodhouse - * Steven J. Hill + * Steven J. Hill * Thomas Gleixner * - * $Id: nand.h,v 1.68 2004/11/12 10:40:37 gleixner Exp $ + * $Id: nand.h,v 1.74 2005/09/15 13:58:50 vwool Exp $ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * - * Info: - * Contains standard defines and IDs for NAND flash devices + * Info: + * Contains standard defines and IDs for NAND flash devices * - * Changelog: - * 01-31-2000 DMW Created - * 09-18-2000 SJH Moved structure out of the Disk-On-Chip drivers - * so it can be used by other NAND flash device - * drivers. I also changed the copyright since none - * of the original contents of this file are specific - * to DoC devices. David can whack me with a baseball - * bat later if I did something naughty. - * 10-11-2000 SJH Added private NAND flash structure for driver - * 10-24-2000 SJH Added prototype for 'nand_scan' function - * 10-29-2001 TG changed nand_chip structure to support - * hardwarespecific function for accessing control lines - * 02-21-2002 TG added support for different read/write adress and - * ready/busy line access function - * 02-26-2002 TG added chip_delay to nand_chip structure to optimize - * command delay times for different chips - * 04-28-2002 TG OOB config defines moved from nand.c to avoid duplicate - * defines in jffs2/wbuf.c - * 08-07-2002 TG forced bad block location to byte 5 of OOB, even if - * CONFIG_MTD_NAND_ECC_JFFS2 is not set - * 08-10-2002 TG extensions to nand_chip structure to support HW-ECC - * - * 08-29-2002 tglx nand_chip structure: data_poi for selecting - * internal / fs-driver buffer - * support for 6byte/512byte hardware ECC - * read_ecc, write_ecc extended for different oob-layout - * oob layout selections: NAND_NONE_OOB, NAND_JFFS2_OOB, - * NAND_YAFFS_OOB - * 11-25-2002 tglx Added Manufacturer code FUJITSU, NATIONAL - * Split manufacturer and device ID structures - * - * 02-08-2004 tglx added option field to nand structure for chip anomalities - * 05-25-2004 tglx added bad block table support, ST-MICRO manufacturer id - * update of nand_chip structure description + * Changelog: + * See git changelog. */ #ifndef __LINUX_MTD_NAND_H #define __LINUX_MTD_NAND_H -#include +/* XXX U-BOOT XXX */ +#if 0 +#include +#include #include +#endif + +#include "config.h" + +#include "linux/mtd/compat.h" +#include "linux/mtd/mtd.h" + struct mtd_info; /* Scan and identify a NAND device */ extern int nand_scan (struct mtd_info *mtd, int max_chips); +/* Separate phases of nand_scan(), allowing board driver to intervene + * and override command or ECC setup according to flash type */ +extern int nand_scan_ident(struct mtd_info *mtd, int max_chips); +extern int nand_scan_tail(struct mtd_info *mtd); + /* Free resources held by the NAND device */ extern void nand_release (struct mtd_info *mtd); -/* Read raw data from the device without ECC */ -extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_t len, size_t ooblen); +/* Internal helper for board drivers which need to override command function */ +extern void nand_wait_ready(struct mtd_info *mtd); +/* The maximum number of NAND chips in an array */ +#ifndef NAND_MAX_CHIPS +#define NAND_MAX_CHIPS 8 +#endif /* This constant declares the max. oobsize / page, which * is supported now. If you add a chip with bigger oobsize/page * adjust this accordingly. */ -#define NAND_MAX_OOBSIZE 64 +#define NAND_MAX_OOBSIZE 128 +#define NAND_MAX_PAGESIZE 4096 /* * Constants for hardware specific CLE/ALE/NCE function -*/ + * + * These are bits which can be or'ed to set/clear multiple + * bits in one go. + */ /* Select the chip by setting nCE to low */ -#define NAND_CTL_SETNCE 1 -/* Deselect the chip by setting nCE to high */ -#define NAND_CTL_CLRNCE 2 +#define NAND_NCE 0x01 /* Select the command latch by setting CLE to high */ -#define NAND_CTL_SETCLE 3 -/* Deselect the command latch by setting CLE to low */ -#define NAND_CTL_CLRCLE 4 +#define NAND_CLE 0x02 /* Select the address latch by setting ALE to high */ -#define NAND_CTL_SETALE 5 -/* Deselect the address latch by setting ALE to low */ -#define NAND_CTL_CLRALE 6 -/* Set write protection by setting WP to high. Not used! */ -#define NAND_CTL_SETWP 7 -/* Clear write protection by setting WP to low. Not used! */ -#define NAND_CTL_CLRWP 8 +#define NAND_ALE 0x04 + +#define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) +#define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) +#define NAND_CTRL_CHANGE 0x80 /* * Standard NAND flash commands */ #define NAND_CMD_READ0 0 #define NAND_CMD_READ1 1 +#define NAND_CMD_RNDOUT 5 #define NAND_CMD_PAGEPROG 0x10 #define NAND_CMD_READOOB 0x50 #define NAND_CMD_ERASE1 0x60 #define NAND_CMD_STATUS 0x70 #define NAND_CMD_STATUS_MULTI 0x71 #define NAND_CMD_SEQIN 0x80 +#define NAND_CMD_RNDIN 0x85 #define NAND_CMD_READID 0x90 #define NAND_CMD_ERASE2 0xd0 #define NAND_CMD_RESET 0xff /* Extended commands for large page devices */ #define NAND_CMD_READSTART 0x30 +#define NAND_CMD_RNDOUTSTART 0xE0 #define NAND_CMD_CACHEDPROG 0x15 +/* Extended commands for AG-AND device */ +/* + * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but + * there is no way to distinguish that from NAND_CMD_READ0 + * until the remaining sequence of commands has been completed + * so add a high order bit and mask it off in the command. + */ +#define NAND_CMD_DEPLETE1 0x100 +#define NAND_CMD_DEPLETE2 0x38 +#define NAND_CMD_STATUS_MULTI 0x71 +#define NAND_CMD_STATUS_ERROR 0x72 +/* multi-bank error status (banks 0-3) */ +#define NAND_CMD_STATUS_ERROR0 0x73 +#define NAND_CMD_STATUS_ERROR1 0x74 +#define NAND_CMD_STATUS_ERROR2 0x75 +#define NAND_CMD_STATUS_ERROR3 0x76 +#define NAND_CMD_STATUS_RESET 0x7f +#define NAND_CMD_STATUS_CLEAR 0xff + +#define NAND_CMD_NONE -1 + /* Status bits */ #define NAND_STATUS_FAIL 0x01 #define NAND_STATUS_FAIL_N1 0x02 @@ -120,25 +129,16 @@ extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_ /* * Constants for ECC_MODES */ - -/* No ECC. Usage is not recommended ! */ -#define NAND_ECC_NONE 0 -/* Software ECC 3 byte ECC per 256 Byte data */ -#define NAND_ECC_SOFT 1 -/* Hardware ECC 3 byte ECC per 256 Byte data */ -#define NAND_ECC_HW3_256 2 -/* Hardware ECC 3 byte ECC per 512 Byte data */ -#define NAND_ECC_HW3_512 3 -/* Hardware ECC 6 byte ECC per 512 Byte data */ -#define NAND_ECC_HW6_512 4 -/* Hardware ECC 8 byte ECC per 512 Byte data */ -#define NAND_ECC_HW8_512 6 -/* Hardware ECC 12 byte ECC per 2048 Byte data */ -#define NAND_ECC_HW12_2048 7 +typedef enum { + NAND_ECC_NONE, + NAND_ECC_SOFT, + NAND_ECC_HW, + NAND_ECC_HW_SYNDROME, +} nand_ecc_modes_t; /* * Constants for Hardware ECC -*/ + */ /* Reset Hardware ECC for read */ #define NAND_ECC_READ 0 /* Reset Hardware ECC for write */ @@ -146,6 +146,10 @@ extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_ /* Enable Hardware ECC before syndrom is read back from flash */ #define NAND_ECC_READSYN 2 +/* Bit mask for flags passed to do_nand_read_ecc */ +#define NAND_GET_DEVICE 0x80 + + /* Option constants for bizarre disfunctionality and real * features */ @@ -165,6 +169,17 @@ extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_ /* Chip has a array of 4 pages which can be read without * additional ready /busy waits */ #define NAND_4PAGE_ARRAY 0x00000040 +/* Chip requires that BBT is periodically rewritten to prevent + * bits from adjacent blocks from 'leaking' in altering data. + * This happens with the Renesas AG-AND chips, possibly others. */ +#define BBT_AUTO_REFRESH 0x00000080 +/* Chip does not require ready check on read. True + * for all large page devices, as they do not support + * autoincrement.*/ +#define NAND_NO_READRDY 0x00000100 +/* Chip does not allow subpage writes */ +#define NAND_NO_SUBPAGE_WRITE 0x00000200 + /* Options valid for Samsung large page devices */ #define NAND_SAMSUNG_LP_OPTIONS \ @@ -183,18 +198,18 @@ extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_ /* Use a flash based bad block table. This option is passed to the * default bad block table function. */ #define NAND_USE_FLASH_BBT 0x00010000 -/* The hw ecc generator provides a syndrome instead a ecc value on read - * This can only work if we have the ecc bytes directly behind the - * data bytes. Applies for DOC and AG-AND Renesas HW Reed Solomon generators */ -#define NAND_HWECC_SYNDROME 0x00020000 - - +/* This option skips the bbt scan during initialization. */ +#define NAND_SKIP_BBTSCAN 0x00020000 +/* This option is defined if the board driver allocates its own buffers + (e.g. because it needs them DMA-coherent */ +#define NAND_OWN_BUFFERS 0x00040000 /* Options set by nand scan */ -/* Nand scan has allocated oob_buf */ -#define NAND_OOBBUF_ALLOC 0x40000000 -/* Nand scan has allocated data_buf */ -#define NAND_DATABUF_ALLOC 0x80000000 +/* Nand scan has allocated controller struct */ +#define NAND_CONTROLLER_ALLOC 0x80000000 +/* Cell info constants */ +#define NAND_CI_CHIPNR_MSK 0x03 +#define NAND_CI_CELLTYPE_MSK 0x0C /* * nand_state_t - chip states @@ -207,135 +222,216 @@ typedef enum { FL_ERASING, FL_SYNCING, FL_CACHEDPRG, + FL_PM_SUSPENDED, } nand_state_t; /* Keep gcc happy */ struct nand_chip; -#if 0 /** - * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independend devices - * @lock: protection lock + * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices + * @lock: protection lock * @active: the mtd device which holds the controller currently + * @wq: wait queue to sleep on if a NAND operation is in progress + * used instead of the per chip wait queue when a hw controller is available */ struct nand_hw_control { - spinlock_t lock; - struct nand_chip *active; -}; +#if 0 + spinlock_t lock; + wait_queue_head_t wq; #endif + struct nand_chip *active; +}; + +/** + * struct nand_ecc_ctrl - Control structure for ecc + * @mode: ecc mode + * @steps: number of ecc steps per page + * @size: data bytes per ecc step + * @bytes: ecc bytes per step + * @total: total number of ecc bytes per page + * @prepad: padding information for syndrome based ecc generators + * @postpad: padding information for syndrome based ecc generators + * @layout: ECC layout control struct pointer + * @hwctl: function to control hardware ecc generator. Must only + * be provided if an hardware ECC is available + * @calculate: function for ecc calculation or readback from ecc hardware + * @correct: function for ecc correction, matching to ecc generator (sw/hw) + * @read_page_raw: function to read a raw page without ECC + * @write_page_raw: function to write a raw page without ECC + * @read_page: function to read a page according to the ecc generator requirements + * @write_page: function to write a page according to the ecc generator requirements + * @read_oob: function to read chip OOB data + * @write_oob: function to write chip OOB data + */ +struct nand_ecc_ctrl { + nand_ecc_modes_t mode; + int steps; + int size; + int bytes; + int total; + int prepad; + int postpad; + struct nand_ecclayout *layout; + void (*hwctl)(struct mtd_info *mtd, int mode); + int (*calculate)(struct mtd_info *mtd, + const uint8_t *dat, + uint8_t *ecc_code); + int (*correct)(struct mtd_info *mtd, uint8_t *dat, + uint8_t *read_ecc, + uint8_t *calc_ecc); + int (*read_page_raw)(struct mtd_info *mtd, + struct nand_chip *chip, + uint8_t *buf); + void (*write_page_raw)(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf); + int (*read_page)(struct mtd_info *mtd, + struct nand_chip *chip, + uint8_t *buf); + void (*write_page)(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf); + int (*read_oob)(struct mtd_info *mtd, + struct nand_chip *chip, + int page, + int sndcmd); + int (*write_oob)(struct mtd_info *mtd, + struct nand_chip *chip, + int page); +}; + +/** + * struct nand_buffers - buffer structure for read/write + * @ecccalc: buffer for calculated ecc + * @ecccode: buffer for ecc read from flash + * @databuf: buffer for data - dynamically sized + * + * Do not change the order of buffers. databuf and oobrbuf must be in + * consecutive order. + */ +struct nand_buffers { + uint8_t ecccalc[NAND_MAX_OOBSIZE]; + uint8_t ecccode[NAND_MAX_OOBSIZE]; + uint8_t databuf[NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE]; +}; /** * struct nand_chip - NAND Private Flash Chip Data * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device * @read_byte: [REPLACEABLE] read one byte from the chip - * @write_byte: [REPLACEABLE] write one byte to the chip * @read_word: [REPLACEABLE] read one word from the chip - * @write_word: [REPLACEABLE] write one word to the chip * @write_buf: [REPLACEABLE] write data from the buffer to the chip * @read_buf: [REPLACEABLE] read data from the chip into the buffer * @verify_buf: [REPLACEABLE] verify buffer contents against the chip data * @select_chip: [REPLACEABLE] select chip nr * @block_bad: [REPLACEABLE] check, if the block is bad * @block_markbad: [REPLACEABLE] mark the block bad - * @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines + * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific funtion for controlling + * ALE/CLE/nCE. Also used to write command and address * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line * If set to NULL no access to ready/busy is available and the ready/busy information * is read from the chip status register * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready - * @calculate_ecc: [REPLACEABLE] function for ecc calculation or readback from ecc hardware - * @correct_data: [REPLACEABLE] function for ecc correction, matching to ecc generator (sw/hw) - * @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only - * be provided if a hardware ECC is available + * @ecc: [BOARDSPECIFIC] ecc control ctructure + * @buffers: buffer structure for read/write + * @hwcontrol: platform-specific hardware control structure + * @ops: oob operation operands * @erase_cmd: [INTERN] erase command write function, selectable due to AND support * @scan_bbt: [REPLACEABLE] function to scan bad block table - * @eccmode: [BOARDSPECIFIC] mode of ecc, see defines - * @eccsize: [INTERN] databytes used per ecc-calculation - * @eccbytes: [INTERN] number of ecc bytes per ecc-calculation step - * @eccsteps: [INTERN] number of ecc calculation steps per page * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR) - * @chip_lock: [INTERN] spinlock used to protect access to this structure and the chip * @wq: [INTERN] wait queue to sleep on if a NAND operation is in progress * @state: [INTERN] the current state of the NAND device + * @oob_poi: poison value buffer * @page_shift: [INTERN] number of address bits in a page (column address bits) * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry * @chip_shift: [INTERN] number of address bits in one chip - * @data_buf: [INTERN] internal buffer for one page + oob - * @oob_buf: [INTERN] oob buffer for one eraseblock + * @datbuf: [INTERN] internal buffer for one page + oob + * @oobbuf: [INTERN] oob buffer for one eraseblock * @oobdirty: [INTERN] indicates that oob_buf must be reinitialized * @data_poi: [INTERN] pointer to a data buffer * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about * special functionality. See the defines for further explanation * @badblockpos: [INTERN] position of the bad block marker in the oob area + * @cellinfo: [INTERN] MLC/multichip data from chip ident * @numchips: [INTERN] number of physical chips * @chipsize: [INTERN] the size of one chip for multichip arrays * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 * @pagebuf: [INTERN] holds the pagenumber which is currently in data_buf - * @autooob: [REPLACEABLE] the default (auto)placement scheme + * @subpagesize: [INTERN] holds the subpagesize + * @ecclayout: [REPLACEABLE] the default ecc placement scheme * @bbt: [INTERN] bad block table pointer * @bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup * @bbt_md: [REPLACEABLE] bad block table mirror descriptor * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan - * @controller: [OPTIONAL] a pointer to a hardware controller structure which is shared among multiple independend devices + * @controller: [REPLACEABLE] a pointer to a hardware controller structure + * which is shared among multiple independend devices * @priv: [OPTIONAL] pointer to private chip date + * @errstat: [OPTIONAL] hardware specific function to perform additional error status checks + * (determine if errors are correctable) + * @write_page: [REPLACEABLE] High-level page write function */ struct nand_chip { void __iomem *IO_ADDR_R; void __iomem *IO_ADDR_W; - u_char (*read_byte)(struct mtd_info *mtd); - void (*write_byte)(struct mtd_info *mtd, u_char byte); + uint8_t (*read_byte)(struct mtd_info *mtd); u16 (*read_word)(struct mtd_info *mtd); - void (*write_word)(struct mtd_info *mtd, u16 word); - - void (*write_buf)(struct mtd_info *mtd, const u_char *buf, int len); - void (*read_buf)(struct mtd_info *mtd, u_char *buf, int len); - int (*verify_buf)(struct mtd_info *mtd, const u_char *buf, int len); + void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); + void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); + int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); void (*select_chip)(struct mtd_info *mtd, int chip); int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); - void (*hwcontrol)(struct mtd_info *mtd, int cmd); + void (*cmd_ctrl)(struct mtd_info *mtd, int dat, + unsigned int ctrl); int (*dev_ready)(struct mtd_info *mtd); void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr); - int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this, int state); - int (*calculate_ecc)(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code); - int (*correct_data)(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc); - void (*enable_hwecc)(struct mtd_info *mtd, int mode); + int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); void (*erase_cmd)(struct mtd_info *mtd, int page); int (*scan_bbt)(struct mtd_info *mtd); - int eccmode; - int eccsize; - int eccbytes; - int eccsteps; + int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, int status, int page); + int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int page, int cached, int raw); + int chip_delay; -#if 0 - spinlock_t chip_lock; - wait_queue_head_t wq; - nand_state_t state; -#endif + unsigned int options; + int page_shift; int phys_erase_shift; int bbt_erase_shift; int chip_shift; - u_char *data_buf; - u_char *oob_buf; - int oobdirty; - u_char *data_poi; - unsigned int options; - int badblockpos; int numchips; unsigned long chipsize; int pagemask; int pagebuf; - struct nand_oobinfo *autooob; + int subpagesize; + uint8_t cellinfo; + int badblockpos; + + nand_state_t state; + + uint8_t *oob_poi; + struct nand_hw_control *controller; + struct nand_ecclayout *ecclayout; + + struct nand_ecc_ctrl ecc; + struct nand_buffers *buffers; + + struct nand_hw_control hwcontrol; + + struct mtd_oob_ops ops; + uint8_t *bbt; struct nand_bbt_descr *bbt_td; struct nand_bbt_descr *bbt_md; + struct nand_bbt_descr *badblock_pattern; - struct nand_hw_control *controller; + void *priv; }; @@ -348,11 +444,11 @@ struct nand_chip { #define NAND_MFR_NATIONAL 0x8f #define NAND_MFR_RENESAS 0x07 #define NAND_MFR_STMICRO 0x20 +#define NAND_MFR_HYNIX 0xad #define NAND_MFR_MICRON 0x2c /** * struct nand_flash_dev - NAND Flash Device ID Structure - * * @name: Identify the device type * @id: device ID code * @pagesize: Pagesize in bytes. Either 256 or 512 or 0 @@ -403,7 +499,7 @@ extern struct nand_manufacturers nand_manuf_ids[]; * blocks is reserved at the end of the device where the tables are * written. * @reserved_block_code: if non-0, this pattern denotes a reserved (rather than - * bad) block in the stored bbt + * bad) block in the stored bbt * @pattern: pattern to identify bad block table or factory marked good / * bad blocks, can be NULL, if len = 0 * @@ -417,11 +513,11 @@ struct nand_bbt_descr { int pages[NAND_MAX_CHIPS]; int offs; int veroffs; - uint8_t version[NAND_MAX_CHIPS]; + uint8_t version[NAND_MAX_CHIPS]; int len; int maxblocks; int reserved_block_code; - uint8_t *pattern; + uint8_t *pattern; }; /* Options for the bad block table descriptors */ @@ -433,7 +529,7 @@ struct nand_bbt_descr { #define NAND_BBT_4BIT 0x00000004 #define NAND_BBT_8BIT 0x00000008 /* The bad block table is in the last good block of the device */ -#define NAND_BBT_LASTBLOCK 0x00000010 +#define NAND_BBT_LASTBLOCK 0x00000010 /* The bbt is at the given page, else we must scan for the bbt */ #define NAND_BBT_ABSPAGE 0x00000020 /* The bbt is at the given page, else we must scan for the bbt */ @@ -456,13 +552,16 @@ struct nand_bbt_descr { #define NAND_BBT_SCAN2NDPAGE 0x00004000 /* The maximum number of blocks to scan for a bbt */ -#define NAND_BBT_SCAN_MAXBLOCKS 4 +#define NAND_BBT_SCAN_MAXBLOCKS 4 -extern int nand_scan_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd); -extern int nand_update_bbt (struct mtd_info *mtd, loff_t offs); -extern int nand_default_bbt (struct mtd_info *mtd); -extern int nand_isbad_bbt (struct mtd_info *mtd, loff_t offs, int allowbbt); -extern int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbbt); +extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd); +extern int nand_update_bbt(struct mtd_info *mtd, loff_t offs); +extern int nand_default_bbt(struct mtd_info *mtd); +extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); +extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, + int allowbbt); +extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t * retlen, uint8_t * buf); /* * Constants for oob configuration @@ -470,4 +569,67 @@ extern int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int #define NAND_SMALL_BADBLOCK_POS 5 #define NAND_LARGE_BADBLOCK_POS 0 +/** + * struct platform_nand_chip - chip level device structure + * @nr_chips: max. number of chips to scan for + * @chip_offset: chip number offset + * @nr_partitions: number of partitions pointed to by partitions (or zero) + * @partitions: mtd partition list + * @chip_delay: R/B delay value in us + * @options: Option flags, e.g. 16bit buswidth + * @ecclayout: ecc layout info structure + * @part_probe_types: NULL-terminated array of probe types + * @priv: hardware controller specific settings + */ +struct platform_nand_chip { + int nr_chips; + int chip_offset; + int nr_partitions; + struct mtd_partition *partitions; + struct nand_ecclayout *ecclayout; + int chip_delay; + unsigned int options; + const char **part_probe_types; + void *priv; +}; + +/** + * struct platform_nand_ctrl - controller level device structure + * @hwcontrol: platform specific hardware control structure + * @dev_ready: platform specific function to read ready/busy pin + * @select_chip: platform specific chip select function + * @cmd_ctrl: platform specific function for controlling + * ALE/CLE/nCE. Also used to write command and address + * @priv: private data to transport driver specific settings + * + * All fields are optional and depend on the hardware driver requirements + */ +struct platform_nand_ctrl { + void (*hwcontrol)(struct mtd_info *mtd, int cmd); + int (*dev_ready)(struct mtd_info *mtd); + void (*select_chip)(struct mtd_info *mtd, int chip); + void (*cmd_ctrl)(struct mtd_info *mtd, int dat, + unsigned int ctrl); + void *priv; +}; + +/** + * struct platform_nand_data - container structure for platform-specific data + * @chip: chip level chip structure + * @ctrl: controller level device structure + */ +struct platform_nand_data { + struct platform_nand_chip chip; + struct platform_nand_ctrl ctrl; +}; + +/* Some helpers to access the data structures */ +static inline +struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + + return chip->priv; +} + #endif /* __LINUX_MTD_NAND_H */ diff --git a/include/linux/mtd/nftl-user.h b/include/linux/mtd/nftl-user.h new file mode 100644 index 0000000000..b2bca18e73 --- /dev/null +++ b/include/linux/mtd/nftl-user.h @@ -0,0 +1,76 @@ +/* + * $Id: nftl-user.h,v 1.2 2005/11/07 11:14:56 gleixner Exp $ + * + * Parts of NFTL headers shared with userspace + * + */ + +#ifndef __MTD_NFTL_USER_H__ +#define __MTD_NFTL_USER_H__ + +/* Block Control Information */ + +struct nftl_bci { + unsigned char ECCSig[6]; + uint8_t Status; + uint8_t Status1; +}__attribute__((packed)); + +/* Unit Control Information */ + +struct nftl_uci0 { + uint16_t VirtUnitNum; + uint16_t ReplUnitNum; + uint16_t SpareVirtUnitNum; + uint16_t SpareReplUnitNum; +} __attribute__((packed)); + +struct nftl_uci1 { + uint32_t WearInfo; + uint16_t EraseMark; + uint16_t EraseMark1; +} __attribute__((packed)); + +struct nftl_uci2 { + uint16_t FoldMark; + uint16_t FoldMark1; + uint32_t unused; +} __attribute__((packed)); + +union nftl_uci { + struct nftl_uci0 a; + struct nftl_uci1 b; + struct nftl_uci2 c; +}; + +struct nftl_oob { + struct nftl_bci b; + union nftl_uci u; +}; + +/* NFTL Media Header */ + +struct NFTLMediaHeader { + char DataOrgID[6]; + uint16_t NumEraseUnits; + uint16_t FirstPhysicalEUN; + uint32_t FormattedSize; + unsigned char UnitSizeFactor; +} __attribute__((packed)); + +#define MAX_ERASE_ZONES (8192 - 512) + +#define ERASE_MARK 0x3c69 +#define SECTOR_FREE 0xff +#define SECTOR_USED 0x55 +#define SECTOR_IGNORE 0x11 +#define SECTOR_DELETED 0x00 + +#define FOLD_MARK_IN_PROGRESS 0x5555 + +#define ZONE_GOOD 0xff +#define ZONE_BAD_ORIGINAL 0 +#define ZONE_BAD_MARKED 7 + + +#endif /* __MTD_NFTL_USER_H__ */ diff --git a/include/linux/mtd/nftl.h b/include/linux/mtd/nftl.h index b0337c3401..04963a52e5 100644 --- a/include/linux/mtd/nftl.h +++ b/include/linux/mtd/nftl.h @@ -1,75 +1,16 @@ - -/* Defines for NAND Flash Translation Layer */ -/* (c) 1999 Machine Vision Holdings, Inc. */ -/* Author: David Woodhouse */ -/* $Id: nftl.h,v 1.10 2000/12/29 00:25:38 dwmw2 Exp $ */ +/* + * $Id: nftl.h,v 1.16 2004/06/30 14:49:00 dbrown Exp $ + * + * (C) 1999-2003 David Woodhouse + */ #ifndef __MTD_NFTL_H__ #define __MTD_NFTL_H__ -/* Block Control Information */ - -struct nftl_bci { - unsigned char ECCSig[6]; - __u8 Status; - __u8 Status1; -}__attribute__((packed)); - -/* Unit Control Information */ - -struct nftl_uci0 { - __u16 VirtUnitNum; - __u16 ReplUnitNum; - __u16 SpareVirtUnitNum; - __u16 SpareReplUnitNum; -} __attribute__((packed)); - -struct nftl_uci1 { - __u32 WearInfo; - __u16 EraseMark; - __u16 EraseMark1; -} __attribute__((packed)); +#include +#include -struct nftl_uci2 { - __u16 FoldMark; - __u16 FoldMark1; - __u32 unused; -} __attribute__((packed)); - -union nftl_uci { - struct nftl_uci0 a; - struct nftl_uci1 b; - struct nftl_uci2 c; -}; - -struct nftl_oob { - struct nftl_bci b; - union nftl_uci u; -}; - -/* NFTL Media Header */ - -struct NFTLMediaHeader { - char DataOrgID[6]; - __u16 NumEraseUnits; - __u16 FirstPhysicalEUN; - __u32 FormattedSize; - unsigned char UnitSizeFactor; -} __attribute__((packed)); - -#define MAX_ERASE_ZONES (8192 - 512) - -#define ERASE_MARK 0x3c69 -#define SECTOR_FREE 0xff -#define SECTOR_USED 0x55 -#define SECTOR_IGNORE 0x11 -#define SECTOR_DELETED 0x00 - -#define FOLD_MARK_IN_PROGRESS 0x5555 - -#define ZONE_GOOD 0xff -#define ZONE_BAD_ORIGINAL 0 -#define ZONE_BAD_MARKED 7 +#include /* these info are used in ReplUnitTable */ #define BLOCK_NIL 0xffff /* last block of a chain */ @@ -78,7 +19,7 @@ struct NFTLMediaHeader { #define BLOCK_RESERVED 0xfffc /* bios block or bad block */ struct NFTLrecord { - struct DiskOnChip *mtd; + struct mtd_blktrans_dev mbd; __u16 MediaUnit, SpareMediaUnit; __u32 EraseSize; struct NFTLMediaHeader MediaHdr; @@ -90,16 +31,24 @@ struct NFTLrecord { __u16 lastEUN; /* should be suppressed */ __u16 numfreeEUNs; __u16 LastFreeEUN; /* To speed up finding a free EUN */ - __u32 nr_sects; int head,sect,cyl; __u16 *EUNtable; /* [numvunits]: First EUN for each virtual unit */ __u16 *ReplUnitTable; /* [numEUNs]: ReplUnitNumber for each */ - unsigned int nb_blocks; /* number of physical blocks */ - unsigned int nb_boot_blocks; /* number of blocks used by the bios */ + unsigned int nb_blocks; /* number of physical blocks */ + unsigned int nb_boot_blocks; /* number of blocks used by the bios */ + struct erase_info instr; + struct nand_ecclayout oobinfo; }; +int NFTL_mount(struct NFTLrecord *s); +int NFTL_formatblock(struct NFTLrecord *s, int block); + +#ifndef NFTL_MAJOR +#define NFTL_MAJOR 93 +#endif + #define MAX_NFTLS 16 -#define MAX_SECTORS_PER_UNIT 32 +#define MAX_SECTORS_PER_UNIT 64 #define NFTL_PARTN_BITS 4 #endif /* __MTD_NFTL_H__ */ diff --git a/include/linux/mtd/ubi-header.h b/include/linux/mtd/ubi-header.h new file mode 100644 index 0000000000..fa479c71aa --- /dev/null +++ b/include/linux/mtd/ubi-header.h @@ -0,0 +1,360 @@ +/* + * Copyright (c) International Business Machines Corp., 2006 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See + * the GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Authors: Artem Bityutskiy (Битюцкий Артём) + * Thomas Gleixner + * Frank Haverkamp + * Oliver Lohmann + * Andreas Arnez + */ + +/* + * This file defines the layout of UBI headers and all the other UBI on-flash + * data structures. May be included by user-space. + */ + +#ifndef __UBI_HEADER_H__ +#define __UBI_HEADER_H__ + +#include + +/* The version of UBI images supported by this implementation */ +#define UBI_VERSION 1 + +/* The highest erase counter value supported by this implementation */ +#define UBI_MAX_ERASECOUNTER 0x7FFFFFFF + +/* The initial CRC32 value used when calculating CRC checksums */ +#define UBI_CRC32_INIT 0xFFFFFFFFU + +/* Erase counter header magic number (ASCII "UBI#") */ +#define UBI_EC_HDR_MAGIC 0x55424923 +/* Volume identifier header magic number (ASCII "UBI!") */ +#define UBI_VID_HDR_MAGIC 0x55424921 + +/* + * Volume type constants used in the volume identifier header. + * + * @UBI_VID_DYNAMIC: dynamic volume + * @UBI_VID_STATIC: static volume + */ +enum { + UBI_VID_DYNAMIC = 1, + UBI_VID_STATIC = 2 +}; + +/* + * Compatibility constants used by internal volumes. + * + * @UBI_COMPAT_DELETE: delete this internal volume before anything is written + * to the flash + * @UBI_COMPAT_RO: attach this device in read-only mode + * @UBI_COMPAT_PRESERVE: preserve this internal volume - do not touch its + * physical eraseblocks, don't allow the wear-leveling unit to move them + * @UBI_COMPAT_REJECT: reject this UBI image + */ +enum { + UBI_COMPAT_DELETE = 1, + UBI_COMPAT_RO = 2, + UBI_COMPAT_PRESERVE = 4, + UBI_COMPAT_REJECT = 5 +}; + +/* + * ubi16_t/ubi32_t/ubi64_t - 16, 32, and 64-bit integers used in UBI on-flash + * data structures. + */ +typedef struct { + uint16_t int16; +} __attribute__ ((packed)) ubi16_t; + +typedef struct { + uint32_t int32; +} __attribute__ ((packed)) ubi32_t; + +typedef struct { + uint64_t int64; +} __attribute__ ((packed)) ubi64_t; + +/* + * In this implementation of UBI uses the big-endian format for on-flash + * integers. The below are the corresponding conversion macros. + */ +#define cpu_to_ubi16(x) ((ubi16_t){__cpu_to_be16(x)}) +#define ubi16_to_cpu(x) ((uint16_t)__be16_to_cpu((x).int16)) + +#define cpu_to_ubi32(x) ((ubi32_t){__cpu_to_be32(x)}) +#define ubi32_to_cpu(x) ((uint32_t)__be32_to_cpu((x).int32)) + +#define cpu_to_ubi64(x) ((ubi64_t){__cpu_to_be64(x)}) +#define ubi64_to_cpu(x) ((uint64_t)__be64_to_cpu((x).int64)) + +/* Sizes of UBI headers */ +#define UBI_EC_HDR_SIZE sizeof(struct ubi_ec_hdr) +#define UBI_VID_HDR_SIZE sizeof(struct ubi_vid_hdr) + +/* Sizes of UBI headers without the ending CRC */ +#define UBI_EC_HDR_SIZE_CRC (UBI_EC_HDR_SIZE - sizeof(ubi32_t)) +#define UBI_VID_HDR_SIZE_CRC (UBI_VID_HDR_SIZE - sizeof(ubi32_t)) + +/** + * struct ubi_ec_hdr - UBI erase counter header. + * @magic: erase counter header magic number (%UBI_EC_HDR_MAGIC) + * @version: version of UBI implementation which is supposed to accept this + * UBI image + * @padding1: reserved for future, zeroes + * @ec: the erase counter + * @vid_hdr_offset: where the VID header starts + * @data_offset: where the user data start + * @padding2: reserved for future, zeroes + * @hdr_crc: erase counter header CRC checksum + * + * The erase counter header takes 64 bytes and has a plenty of unused space for + * future usage. The unused fields are zeroed. The @version field is used to + * indicate the version of UBI implementation which is supposed to be able to + * work with this UBI image. If @version is greater then the current UBI + * version, the image is rejected. This may be useful in future if something + * is changed radically. This field is duplicated in the volume identifier + * header. + * + * The @vid_hdr_offset and @data_offset fields contain the offset of the the + * volume identifier header and user data, relative to the beginning of the + * physical eraseblock. These values have to be the same for all physical + * eraseblocks. + */ +struct ubi_ec_hdr { + ubi32_t magic; + uint8_t version; + uint8_t padding1[3]; + ubi64_t ec; /* Warning: the current limit is 31-bit anyway! */ + ubi32_t vid_hdr_offset; + ubi32_t data_offset; + uint8_t padding2[36]; + ubi32_t hdr_crc; +} __attribute__ ((packed)); + +/** + * struct ubi_vid_hdr - on-flash UBI volume identifier header. + * @magic: volume identifier header magic number (%UBI_VID_HDR_MAGIC) + * @version: UBI implementation version which is supposed to accept this UBI + * image (%UBI_VERSION) + * @vol_type: volume type (%UBI_VID_DYNAMIC or %UBI_VID_STATIC) + * @copy_flag: if this logical eraseblock was copied from another physical + * eraseblock (for wear-leveling reasons) + * @compat: compatibility of this volume (%0, %UBI_COMPAT_DELETE, + * %UBI_COMPAT_IGNORE, %UBI_COMPAT_PRESERVE, or %UBI_COMPAT_REJECT) + * @vol_id: ID of this volume + * @lnum: logical eraseblock number + * @leb_ver: version of this logical eraseblock (IMPORTANT: obsolete, to be + * removed, kept only for not breaking older UBI users) + * @data_size: how many bytes of data this logical eraseblock contains + * @used_ebs: total number of used logical eraseblocks in this volume + * @data_pad: how many bytes at the end of this physical eraseblock are not + * used + * @data_crc: CRC checksum of the data stored in this logical eraseblock + * @padding1: reserved for future, zeroes + * @sqnum: sequence number + * @padding2: reserved for future, zeroes + * @hdr_crc: volume identifier header CRC checksum + * + * The @sqnum is the value of the global sequence counter at the time when this + * VID header was created. The global sequence counter is incremented each time + * UBI writes a new VID header to the flash, i.e. when it maps a logical + * eraseblock to a new physical eraseblock. The global sequence counter is an + * unsigned 64-bit integer and we assume it never overflows. The @sqnum + * (sequence number) is used to distinguish between older and newer versions of + * logical eraseblocks. + * + * There are 2 situations when there may be more then one physical eraseblock + * corresponding to the same logical eraseblock, i.e., having the same @vol_id + * and @lnum values in the volume identifier header. Suppose we have a logical + * eraseblock L and it is mapped to the physical eraseblock P. + * + * 1. Because UBI may erase physical eraseblocks asynchronously, the following + * situation is possible: L is asynchronously erased, so P is scheduled for + * erasure, then L is written to,i.e. mapped to another physical eraseblock P1, + * so P1 is written to, then an unclean reboot happens. Result - there are 2 + * physical eraseblocks P and P1 corresponding to the same logical eraseblock + * L. But P1 has greater sequence number, so UBI picks P1 when it attaches the + * flash. + * + * 2. From time to time UBI moves logical eraseblocks to other physical + * eraseblocks for wear-leveling reasons. If, for example, UBI moves L from P + * to P1, and an unclean reboot happens before P is physically erased, there + * are two physical eraseblocks P and P1 corresponding to L and UBI has to + * select one of them when the flash is attached. The @sqnum field says which + * PEB is the original (obviously P will have lower @sqnum) and the copy. But + * it is not enough to select the physical eraseblock with the higher sequence + * number, because the unclean reboot could have happen in the middle of the + * copying process, so the data in P is corrupted. It is also not enough to + * just select the physical eraseblock with lower sequence number, because the + * data there may be old (consider a case if more data was added to P1 after + * the copying). Moreover, the unclean reboot may happen when the erasure of P + * was just started, so it result in unstable P, which is "mostly" OK, but + * still has unstable bits. + * + * UBI uses the @copy_flag field to indicate that this logical eraseblock is a + * copy. UBI also calculates data CRC when the data is moved and stores it at + * the @data_crc field of the copy (P1). So when UBI needs to pick one physical + * eraseblock of two (P or P1), the @copy_flag of the newer one (P1) is + * examined. If it is cleared, the situation* is simple and the newer one is + * picked. If it is set, the data CRC of the copy (P1) is examined. If the CRC + * checksum is correct, this physical eraseblock is selected (P1). Otherwise + * the older one (P) is selected. + * + * Note, there is an obsolete @leb_ver field which was used instead of @sqnum + * in the past. But it is not used anymore and we keep it in order to be able + * to deal with old UBI images. It will be removed at some point. + * + * There are 2 sorts of volumes in UBI: user volumes and internal volumes. + * Internal volumes are not seen from outside and are used for various internal + * UBI purposes. In this implementation there is only one internal volume - the + * layout volume. Internal volumes are the main mechanism of UBI extensions. + * For example, in future one may introduce a journal internal volume. Internal + * volumes have their own reserved range of IDs. + * + * The @compat field is only used for internal volumes and contains the "degree + * of their compatibility". It is always zero for user volumes. This field + * provides a mechanism to introduce UBI extensions and to be still compatible + * with older UBI binaries. For example, if someone introduced a journal in + * future, he would probably use %UBI_COMPAT_DELETE compatibility for the + * journal volume. And in this case, older UBI binaries, which know nothing + * about the journal volume, would just delete this volume and work perfectly + * fine. This is similar to what Ext2fs does when it is fed by an Ext3fs image + * - it just ignores the Ext3fs journal. + * + * The @data_crc field contains the CRC checksum of the contents of the logical + * eraseblock if this is a static volume. In case of dynamic volumes, it does + * not contain the CRC checksum as a rule. The only exception is when the + * data of the physical eraseblock was moved by the wear-leveling unit, then + * the wear-leveling unit calculates the data CRC and stores it in the + * @data_crc field. And of course, the @copy_flag is %in this case. + * + * The @data_size field is used only for static volumes because UBI has to know + * how many bytes of data are stored in this eraseblock. For dynamic volumes, + * this field usually contains zero. The only exception is when the data of the + * physical eraseblock was moved to another physical eraseblock for + * wear-leveling reasons. In this case, UBI calculates CRC checksum of the + * contents and uses both @data_crc and @data_size fields. In this case, the + * @data_size field contains data size. + * + * The @used_ebs field is used only for static volumes and indicates how many + * eraseblocks the data of the volume takes. For dynamic volumes this field is + * not used and always contains zero. + * + * The @data_pad is calculated when volumes are created using the alignment + * parameter. So, effectively, the @data_pad field reduces the size of logical + * eraseblocks of this volume. This is very handy when one uses block-oriented + * software (say, cramfs) on top of the UBI volume. + */ +struct ubi_vid_hdr { + ubi32_t magic; + uint8_t version; + uint8_t vol_type; + uint8_t copy_flag; + uint8_t compat; + ubi32_t vol_id; + ubi32_t lnum; + ubi32_t leb_ver; /* obsolete, to be removed, don't use */ + ubi32_t data_size; + ubi32_t used_ebs; + ubi32_t data_pad; + ubi32_t data_crc; + uint8_t padding1[4]; + ubi64_t sqnum; + uint8_t padding2[12]; + ubi32_t hdr_crc; +} __attribute__ ((packed)); + +/* Internal UBI volumes count */ +#define UBI_INT_VOL_COUNT 1 + +/* + * Starting ID of internal volumes. There is reserved room for 4096 internal + * volumes. + */ +#define UBI_INTERNAL_VOL_START (0x7FFFFFFF - 4096) + +/* The layout volume contains the volume table */ + +#define UBI_LAYOUT_VOL_ID UBI_INTERNAL_VOL_START +#define UBI_LAYOUT_VOLUME_EBS 2 +#define UBI_LAYOUT_VOLUME_NAME "layout volume" +#define UBI_LAYOUT_VOLUME_COMPAT UBI_COMPAT_REJECT + +/* The maximum number of volumes per one UBI device */ +#define UBI_MAX_VOLUMES 128 + +/* The maximum volume name length */ +#define UBI_VOL_NAME_MAX 127 + +/* Size of the volume table record */ +#define UBI_VTBL_RECORD_SIZE sizeof(struct ubi_vtbl_record) + +/* Size of the volume table record without the ending CRC */ +#define UBI_VTBL_RECORD_SIZE_CRC (UBI_VTBL_RECORD_SIZE - sizeof(ubi32_t)) + +/** + * struct ubi_vtbl_record - a record in the volume table. + * @reserved_pebs: how many physical eraseblocks are reserved for this volume + * @alignment: volume alignment + * @data_pad: how many bytes are unused at the end of the each physical + * eraseblock to satisfy the requested alignment + * @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME) + * @upd_marker: if volume update was started but not finished + * @name_len: volume name length + * @name: the volume name + * @padding2: reserved, zeroes + * @crc: a CRC32 checksum of the record + * + * The volume table records are stored in the volume table, which is stored in + * the layout volume. The layout volume consists of 2 logical eraseblock, each + * of which contains a copy of the volume table (i.e., the volume table is + * duplicated). The volume table is an array of &struct ubi_vtbl_record + * objects indexed by the volume ID. + * + * If the size of the logical eraseblock is large enough to fit + * %UBI_MAX_VOLUMES records, the volume table contains %UBI_MAX_VOLUMES + * records. Otherwise, it contains as many records as it can fit (i.e., size of + * logical eraseblock divided by sizeof(struct ubi_vtbl_record)). + * + * The @upd_marker flag is used to implement volume update. It is set to %1 + * before update and set to %0 after the update. So if the update operation was + * interrupted, UBI knows that the volume is corrupted. + * + * The @alignment field is specified when the volume is created and cannot be + * later changed. It may be useful, for example, when a block-oriented file + * system works on top of UBI. The @data_pad field is calculated using the + * logical eraseblock size and @alignment. The alignment must be multiple to the + * minimal flash I/O unit. If @alignment is 1, all the available space of + * the physical eraseblocks is used. + * + * Empty records contain all zeroes and the CRC checksum of those zeroes. + */ +struct ubi_vtbl_record { + ubi32_t reserved_pebs; + ubi32_t alignment; + ubi32_t data_pad; + uint8_t vol_type; + uint8_t upd_marker; + ubi16_t name_len; + uint8_t name[UBI_VOL_NAME_MAX+1]; + uint8_t padding2[24]; + ubi32_t crc; +} __attribute__ ((packed)); + +#endif /* !__UBI_HEADER_H__ */ diff --git a/include/linux/mtd/ubi-user.h b/include/linux/mtd/ubi-user.h new file mode 100644 index 0000000000..fe06ded0e6 --- /dev/null +++ b/include/linux/mtd/ubi-user.h @@ -0,0 +1,161 @@ +/* + * Copyright (c) International Business Machines Corp., 2006 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See + * the GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Author: Artem Bityutskiy (Битюцкий Артём) + */ + +#ifndef __UBI_USER_H__ +#define __UBI_USER_H__ + +/* + * UBI volume creation + * ~~~~~~~~~~~~~~~~~~~ + * + * UBI volumes are created via the %UBI_IOCMKVOL IOCTL command of UBI character + * device. A &struct ubi_mkvol_req object has to be properly filled and a + * pointer to it has to be passed to the IOCTL. + * + * UBI volume deletion + * ~~~~~~~~~~~~~~~~~~~ + * + * To delete a volume, the %UBI_IOCRMVOL IOCTL command of the UBI character + * device should be used. A pointer to the 32-bit volume ID hast to be passed + * to the IOCTL. + * + * UBI volume re-size + * ~~~~~~~~~~~~~~~~~~ + * + * To re-size a volume, the %UBI_IOCRSVOL IOCTL command of the UBI character + * device should be used. A &struct ubi_rsvol_req object has to be properly + * filled and a pointer to it has to be passed to the IOCTL. + * + * UBI volume update + * ~~~~~~~~~~~~~~~~~ + * + * Volume update should be done via the %UBI_IOCVOLUP IOCTL command of the + * corresponding UBI volume character device. A pointer to a 64-bit update + * size should be passed to the IOCTL. After then, UBI expects user to write + * this number of bytes to the volume character device. The update is finished + * when the claimed number of bytes is passed. So, the volume update sequence + * is something like: + * + * fd = open("/dev/my_volume"); + * ioctl(fd, UBI_IOCVOLUP, &image_size); + * write(fd, buf, image_size); + * close(fd); + */ + +/* + * When a new volume is created, users may either specify the volume number they + * want to create or to let UBI automatically assign a volume number using this + * constant. + */ +#define UBI_VOL_NUM_AUTO (-1) + +/* Maximum volume name length */ +#define UBI_MAX_VOLUME_NAME 127 + +/* IOCTL commands of UBI character devices */ + +#define UBI_IOC_MAGIC 'o' + +/* Create an UBI volume */ +#define UBI_IOCMKVOL _IOW(UBI_IOC_MAGIC, 0, struct ubi_mkvol_req) +/* Remove an UBI volume */ +#define UBI_IOCRMVOL _IOW(UBI_IOC_MAGIC, 1, int32_t) +/* Re-size an UBI volume */ +#define UBI_IOCRSVOL _IOW(UBI_IOC_MAGIC, 2, struct ubi_rsvol_req) + +/* IOCTL commands of UBI volume character devices */ + +#define UBI_VOL_IOC_MAGIC 'O' + +/* Start UBI volume update */ +#define UBI_IOCVOLUP _IOW(UBI_VOL_IOC_MAGIC, 0, int64_t) +/* An eraseblock erasure command, used for debugging, disabled by default */ +#define UBI_IOCEBER _IOW(UBI_VOL_IOC_MAGIC, 1, int32_t) + +/* + * UBI volume type constants. + * + * @UBI_DYNAMIC_VOLUME: dynamic volume + * @UBI_STATIC_VOLUME: static volume + */ +enum { + UBI_DYNAMIC_VOLUME = 3, + UBI_STATIC_VOLUME = 4 +}; + +/** + * struct ubi_mkvol_req - volume description data structure used in + * volume creation requests. + * @vol_id: volume number + * @alignment: volume alignment + * @bytes: volume size in bytes + * @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME) + * @padding1: reserved for future, not used + * @name_len: volume name length + * @padding2: reserved for future, not used + * @name: volume name + * + * This structure is used by userspace programs when creating new volumes. The + * @used_bytes field is only necessary when creating static volumes. + * + * The @alignment field specifies the required alignment of the volume logical + * eraseblock. This means, that the size of logical eraseblocks will be aligned + * to this number, i.e., + * (UBI device logical eraseblock size) mod (@alignment) = 0. + * + * To put it differently, the logical eraseblock of this volume may be slightly + * shortened in order to make it properly aligned. The alignment has to be + * multiple of the flash minimal input/output unit, or %1 to utilize the entire + * available space of logical eraseblocks. + * + * The @alignment field may be useful, for example, when one wants to maintain + * a block device on top of an UBI volume. In this case, it is desirable to fit + * an integer number of blocks in logical eraseblocks of this UBI volume. With + * alignment it is possible to update this volume using plane UBI volume image + * BLOBs, without caring about how to properly align them. + */ +struct ubi_mkvol_req { + int32_t vol_id; + int32_t alignment; + int64_t bytes; + int8_t vol_type; + int8_t padding1; + int16_t name_len; + int8_t padding2[4]; + char name[UBI_MAX_VOLUME_NAME+1]; +} __attribute__ ((packed)); + +/** + * struct ubi_rsvol_req - a data structure used in volume re-size requests. + * @vol_id: ID of the volume to re-size + * @bytes: new size of the volume in bytes + * + * Re-sizing is possible for both dynamic and static volumes. But while dynamic + * volumes may be re-sized arbitrarily, static volumes cannot be made to be + * smaller then the number of bytes they bear. To arbitrarily shrink a static + * volume, it must be wiped out first (by means of volume update operation with + * zero number of bytes). + */ +struct ubi_rsvol_req { + int64_t bytes; + int32_t vol_id; +} __attribute__ ((packed)); + +#endif /* __UBI_USER_H__ */ diff --git a/include/nand.h b/include/nand.h index e1285cdae9..83d597dc7d 100644 --- a/include/nand.h +++ b/include/nand.h @@ -84,6 +84,7 @@ struct nand_write_options { }; typedef struct nand_write_options nand_write_options_t; +typedef struct mtd_oob_ops mtd_oob_ops_t; struct nand_read_options { u_char *buffer; /* memory block in which read image is written*/ @@ -107,7 +108,7 @@ struct nand_erase_options { typedef struct nand_erase_options nand_erase_options_t; -int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts); +int nand_write_opts(nand_info_t *mtd, loff_t to, mtd_oob_ops_t *ops); int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts); int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts);