From: Paul Gortmaker Date: Fri, 11 Jul 2008 19:33:05 +0000 (-0400) Subject: sbc8560: define eth0 and eth1 instead of eth1 and eth2 X-Git-Tag: v1.3.4-rc1~8^2~10 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=c158bcaca3b31cbe38c4143812e6170e38a57393;p=oweals%2Fu-boot.git sbc8560: define eth0 and eth1 instead of eth1 and eth2 The existing config doesn't define CONFIG_HAS_ETH0, and so the fdt support doesn't update the zeros in the dtb local-mac with real data from the u-boot env. Since the existing config is tailored to just two interfaces, get rid of the ETH2 definitions at the same time. Also don't include any end user specific data into the environment by default -- things like MAC address, network parameters etc. need to come from the end user. Signed-off-by: Paul Gortmaker Signed-off-by: Andy Fleming --- diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index f07fbc09e0..6e4cc4ad85 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -102,11 +102,11 @@ #define CFG_SDRAM_SIZE 512 /* DDR is 512MB */ #define SPD_EEPROM_ADDRESS 0x55 /* DDR DIMM */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #if defined(CONFIG_MPC85xx_REV1) - #define CONFIG_DDR_DLL /* possible DLL fix needed */ + #define CONFIG_DDR_DLL /* possible DLL fix needed */ #endif #undef CONFIG_CLOCKS_IN_MHZ @@ -177,8 +177,8 @@ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO @@ -284,20 +284,20 @@ * FLASH and environment organization */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #if 0 -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_PROTECTION /* use hardware protection */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION /* use hardware protection */ #endif -#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ +#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if 0 /* XXX This doesn't work and I don't want to fix it */ @@ -327,9 +327,8 @@ #define CFG_ENV_SIZE 0x2000 #endif -#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600" +#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=dhcp console=ttyS0,9600" /*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/ -#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000" #define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ @@ -405,19 +404,23 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -# define CONFIG_ETHADDR 00:01:af:07:9b:8a -# define CONFIG_HAS_ETH1 -# define CONFIG_ETH1ADDR 00:01:af:07:9b:8b -# define CONFIG_HAS_ETH2 -# define CONFIG_ETH2ADDR 00:01:af:07:9b:8c +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 #endif -#define CONFIG_SERVERIP 192.168.0.131 -#define CONFIG_IPADDR 192.168.0.105 -#define CONFIG_GATEWAYIP 0.0.0.0 -#define CONFIG_NETMASK 255.255.255.0 +/* You can compile in a MAC address and your custom net settings by using + * the following syntax. Your board should be marked with the assigned + * MAC addresses directly on it. + * + * #define CONFIG_ETHADDR de:ad:be:ef:00:00 + * #define CONFIG_ETH1ADDR fa:ke:ad:dr:es:s! + * #define CONFIG_SERVERIP + * #define CONFIG_IPADDR + * #define CONFIG_GATEWAYIP + * #define CONFIG_NETMASK + */ + #define CONFIG_HOSTNAME SBC8560 #define CONFIG_ROOTPATH /home/ppc #define CONFIG_BOOTFILE pImage