From: 张鹏 Date: Mon, 21 Jan 2019 05:28:32 +0000 (+0800) Subject: ipq40xx: add support for Qxwlan E2600AC C1 and C2 X-Git-Tag: v19.07.0-rc1~1184 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=bbab33724d5fbe3fad87d885adc16ed3dc47742f;p=oweals%2Fopenwrt.git ipq40xx: add support for Qxwlan E2600AC C1 and C2 Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter --- diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 3ce769afc6..62f54fcd7f 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -18,7 +18,7 @@ endef # Please send a mail with your device-specific board files upstream. # You can find instructions and examples on the linux-wireless wiki: # -ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 engenius_eap1300 linksys_ea6350v3 +ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) define Package/ipq-wifi-default @@ -57,5 +57,6 @@ $(eval $(call generate-ipq-wifi-package,alfa-network_ap120c-ac,board-alfa-networ $(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200)) $(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300)) $(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3)) +$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,board-qxwlan-e2600ac.bin,Qxwlan E2600AC)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/package/firmware/ipq-wifi/board-qxwlan-e2600ac.bin b/package/firmware/ipq-wifi/board-qxwlan-e2600ac.bin new file mode 100644 index 0000000000..435b465d89 Binary files /dev/null and b/package/firmware/ipq-wifi/board-qxwlan-e2600ac.bin differ diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index 2fca1cbc9f..d23791eab1 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -39,6 +39,11 @@ netgear,ex6150v2) ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt" ;; +qxwlan,e2600ac-c1 |\ +qxwlan,e2600ac-c2) + ucidef_set_led_wlan "wlan2g" "WLAN0" "e2600ac:green:wlan0" "phy0tpt" + ucidef_set_led_wlan "wlan5g" "WLAN1" "e2600ac:green:wlan1" "phy1tpt" + ;; zyxel,nbg6617) ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index b28f5ef12c..c0466ba8bc 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -48,6 +48,12 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" ;; + qxwlan,e2600ac-c1 |\ + qxwlan,e2600ac-c2) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan" + ;; *) echo "Unsupported hardware. Network interfaces not initialized" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 718224f1e0..44421527d2 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -135,6 +135,14 @@ case "$FIRMWARE" in avm,fritzbox-4040) /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") ;; + compex,wpj428 |\ + engenius,eap1300 |\ + openmesh,a42 |\ + openmesh,a62 |\ + qxwlan,e2600ac-c1 |\ + qxwlan,e2600ac-c2) + ath10kcal_extract "0:ART" 4096 12064 + ;; meraki,mr33) ath10kcal_ubi_extract "ART" 4096 12064 ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064 @@ -145,12 +153,6 @@ case "$FIRMWARE" in ath10kcal_extract "ART" 4096 12064 ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0) ;; - compex,wpj428 |\ - engenius,eap1300 |\ - openmesh,a42 |\ - openmesh,a62) - ath10kcal_extract "0:ART" 4096 12064 - ;; zyxel,nbg6617 |\ zyxel,wre6606) ath10kcal_extract "ART" 4096 12064 @@ -177,6 +179,14 @@ case "$FIRMWARE" in avm,fritzbox-4040) /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") ;; + compex,wpj428 |\ + engenius,eap1300 |\ + openmesh,a42 |\ + openmesh,a62 |\ + qxwlan,e2600ac-c1 |\ + qxwlan,e2600ac-c2) + ath10kcal_extract "0:ART" 20480 12064 + ;; meraki,mr33) ath10kcal_ubi_extract "ART" 20480 12064 ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064 @@ -187,12 +197,6 @@ case "$FIRMWARE" in ath10kcal_extract "ART" 20480 12064 ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12) ;; - compex,wpj428 |\ - engenius,eap1300 |\ - openmesh,a42 |\ - openmesh,a62) - ath10kcal_extract "0:ART" 20480 12064 - ;; zyxel,nbg6617 |\ zyxel,wre6606) ath10kcal_extract "ART" 20480 12064 diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index b92a2bfe9f..87e27aff8f 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -47,7 +47,8 @@ zyxel_do_upgrade() { platform_do_upgrade() { case "$(board_name)" in 8dev,jalapeno |\ - alfa-network,ap120c-ac) + alfa-network,ap120c-ac |\ + qxwlan,e2600ac-c2) nand_do_upgrade "$ARGV" ;; asus,map-ac2200) diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c1.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c1.dts new file mode 100644 index 0000000000..d5ee068c9f --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c1.dts @@ -0,0 +1,80 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT + * + * Copyright (c) 2018 Peng Zhang + * + */ + +#include "qcom-ipq4019-qxwlan-e2600ac.dtsi" +#include +#include + +/ { + model = "Qxwlan E2600AC c1"; + compatible = "qxwlan,e2600ac-c1", "qcom,ipq4019"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + partition@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0x1e80000>; + }; + }; + }; +}; + diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c2.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c2.dts new file mode 100644 index 0000000000..09ebde99ca --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c2.dts @@ -0,0 +1,115 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT + * + * Copyright (c) 2018 Peng Zhang + * + */ + +#include "qcom-ipq4019-qxwlan-e2600ac.dtsi" +#include +#include + +/ { + model = "Qxwlan E2600AC c2"; + compatible = "qxwlan,e2600ac-c2", "qcom,ipq4019"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + }; + }; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x00000000 0x04000000>; + }; + }; + }; +}; + +&tlmm { + nand_pins: nand-pins { + + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac.dtsi b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac.dtsi new file mode 100644 index 0000000000..527df7ec70 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac.dtsi @@ -0,0 +1,262 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT + * + * Copyright (c) 2018 Peng Zhang + * + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + + model = "Qxwlan E2600AC"; + compatible = "qcom,ipq4019"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256MB */ + }; + + soc { + mdio@90000 { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2: usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + serial@78af000 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + serial@78b0000 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + i2c@78b7000 { /* BLSP1 QUP2 */ + pinctrl-0 = <&i2c_0_pins>; + pinctrl-names = "default"; + + status = "okay"; + }; + + usb3: usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + leds { + compatible = "gpio-leds"; + + led1 { + label = "e2600ac:green:wlan0"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + led2 { + label = "e2600ac:green:wlan1"; + gpios = <&tlmm 36 GPIO_ACTIVE_LOW>; + }; + + led3 { + label = "e2600ac:green:usb"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>; + linux,default-trigger = "usbport"; + }; + + led4 { + label = "e2600ac:green:ctrl1"; + gpios = <&tlmm 51 GPIO_ACTIVE_LOW>; + }; + + led5 { + label = "e2600ac:green:ctrl2"; + gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; + }; + + led6 { + label = "e2600ac:green:ctrl3"; + gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + i2c_0_pins: i2c-0-pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_0_pins: serial0-pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "Qxwlan-E2600AC"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "Qxwlan-E2600AC"; +}; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c1.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c1.dts new file mode 100644 index 0000000000..ab0ec76f16 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c1.dts @@ -0,0 +1,80 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT + * + * Copyright (c) 2018 Peng Zhang + * + */ + +#include "qcom-ipq4019-qxwlan-e2600ac.dtsi" +#include +#include + +/ { + model = "Qxwlan E2600AC c1"; + compatible = "qxwlan,e2600ac-c1"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + partition@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0x1e80000>; + }; + }; + }; +}; + diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c2.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c2.dts new file mode 100644 index 0000000000..1c6e859951 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac-c2.dts @@ -0,0 +1,115 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT + * + * Copyright (c) 2018 Peng Zhang + * + */ + +#include "qcom-ipq4019-qxwlan-e2600ac.dtsi" +#include +#include + +/ { + model = "Qxwlan E2600AC c2"; + compatible = "qxwlan,e2600ac-c2"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + }; + }; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x00000000 0x04000000>; + }; + }; + }; +}; + +&tlmm { + nand_pins: nand-pins { + + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac.dtsi b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac.dtsi new file mode 100644 index 0000000000..f4af2ba25f --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac.dtsi @@ -0,0 +1,266 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT + * + * Copyright (c) 2018 Peng Zhang + * + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + + model = "Qxwlan E2600AC"; + compatible = "qcom,ipq4019"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256MB */ + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2: usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + serial@78af000 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + serial@78b0000 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + i2c@78b7000 { /* BLSP1 QUP2 */ + pinctrl-0 = <&i2c_0_pins>; + pinctrl-names = "default"; + + status = "okay"; + }; + + usb3: usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + leds { + compatible = "gpio-leds"; + + led1 { + label = "e2600ac:green:wlan0"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + led2 { + label = "e2600ac:green:wlan1"; + gpios = <&tlmm 36 GPIO_ACTIVE_LOW>; + }; + + led3 { + label = "e2600ac:green:usb"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>; + linux,default-trigger = "usbport"; + }; + + led4 { + label = "e2600ac:green:ctrl1"; + gpios = <&tlmm 51 GPIO_ACTIVE_LOW>; + }; + + led5 { + label = "e2600ac:green:ctrl2"; + gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; + }; + + led6 { + label = "e2600ac:green:ctrl3"; + gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + i2c_0_pins: i2c-0-pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_0_pins: serial0-pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "Qxwlan-E2600AC"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "Qxwlan-E2600AC"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index f7e7ba3d0f..22836be1fb 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -285,6 +285,31 @@ define Device/qcom_ap-dk04.1-c1 endef TARGET_DEVICES += qcom_ap-dk04.1-c1 +define Device/qxwlan_e2600ac-c1 + $(call Device/FitImage) + DEVICE_TITLE := Qxwlan E2600AC-C1 (nor flash) + BOARD_NAME := e2600ac-c1 + DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 31232k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac +endef +TARGET_DEVICES += qxwlan_e2600ac-c1 + +define Device/qxwlan_e2600ac-c2 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2 + KERNEL_INSTALL := 1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_TITLE := Qxwlan E2600AC-C2 (nornand flash) + DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac +endef +TARGET_DEVICES += qxwlan_e2600ac-c2 + define Device/zyxel_nbg6617 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4018-nbg6617 diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch index 551ac6f109..5aeb3963f7 100644 --- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -29,6 +29,8 @@ Signed-off-by: John Crispin + qcom-ipq4019-a62.dtb \ + qcom-ipq4019-ap.dk04.1-c1.dtb \ + qcom-ipq4019-map-ac2200.dtb \ ++ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ ++ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-gl-b1300.dtb \ + qcom-ipq4029-mr33.dtb \ diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 0e27eeab65..bceadc50e8 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -32,6 +32,8 @@ Signed-off-by: John Crispin qcom-ipq4019-ap.dk07.1-c2.dtb \ + qcom-ipq4019-a62.dtb \ + qcom-ipq4019-map-ac2200.dtb \ ++ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ ++ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-gl-b1300.dtb \ + qcom-ipq4029-mr33.dtb \