From: Adrian Schmutzler Date: Sun, 8 Dec 2019 19:18:58 +0000 (+0100) Subject: ath79: add support for GL.iNet 6408/6416 (GL.iNet V1) X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=b4d3110ac1f1f1962f812ac139c437837a448cff;p=oweals%2Fopenwrt.git ath79: add support for GL.iNet 6408/6416 (GL.iNet V1) This ports the GL.iNet 6408/6416 from ar71xx. The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with more DRAM/Flash and console/GPIO header in the same small form-factor. Specifications: - SoC: Atheros AR9331 - CPU: 400 MHz - Flash: 8/16 MiB - RAM: 64 MiB - WiFi: 2.4 GHz b/g/n (SoC) - Ethernet: 2x 100M ports (LAN/WAN) - USB: 1x 2.0 The difference between 6408 and 6416 is just the flash size. It looks like only the 16 MiB version has been advertised, while the 6408 is a modified version. There are also 1-port versions sold by third parties. Installation: Install the sysupgrade image via stock firmware GUI or upload it via uboot (web-based). The device will be available at 192.168.1.1. Attention: In ar71xx, the same board name is used for both flash versions. So, please make sure you flash the correct ath79 image when upgrading. This has been device-tested on a GL.iNet 6416. Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/ar9331_glinet_6408.dts b/target/linux/ath79/dts/ar9331_glinet_6408.dts new file mode 100644 index 0000000000..1215607469 --- /dev/null +++ b/target/linux/ath79/dts/ar9331_glinet_6408.dts @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar9331_glinet_64xx.dtsi" + +/ { + model = "GL.iNet 6408"; + compatible = "glinet,6408", "qca,ar9331"; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + reg = <0x0 0x20000>; + label = "u-boot"; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + reg = <0x20000 0x7d0000>; + label = "firmware"; + }; + + art: partition@7f0000 { + reg = <0x7f0000 0x10000>; + label = "art"; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ath79/dts/ar9331_glinet_6416.dts b/target/linux/ath79/dts/ar9331_glinet_6416.dts new file mode 100644 index 0000000000..5f10b6aada --- /dev/null +++ b/target/linux/ath79/dts/ar9331_glinet_6416.dts @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar9331_glinet_64xx.dtsi" + +/ { + model = "GL.iNet 6416"; + compatible = "glinet,6416", "qca,ar9331"; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + reg = <0x0 0x20000>; + label = "u-boot"; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + reg = <0x20000 0xfd0000>; + label = "firmware"; + }; + + art: partition@ff0000 { + reg = <0xff0000 0x10000>; + label = "art"; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ath79/dts/ar9331_glinet_64xx.dtsi b/target/linux/ath79/dts/ar9331_glinet_64xx.dtsi new file mode 100644 index 0000000000..2fa970248a --- /dev/null +++ b/target/linux/ath79/dts/ar9331_glinet_64xx.dtsi @@ -0,0 +1,91 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include + +#include "ar9331.dtsi" + +/ { + aliases { + serial0 = &uart; + label-mac-device = &wmac; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + wlan { + label = "gl-inet:red:wlan"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + lan { + label = "gl-inet:green:lan"; + gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_usb_vbus: reg_usb_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&uboot 0x1fc00>; + + gmac-config { + device = <&gmac>; + + switch-phy-addr-swap = <0>; + switch-phy-swap = <0>; + }; +}; + +ð1 { + status = "okay"; + + mtd-mac-address = <&uboot 0x1fc00>; +}; + +&gpio { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&usb { + dr_mode = "host"; + vbus-supply = <®_usb_vbus>; + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&uboot 0x1fc00>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 1023ba7a39..43c685b81c 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -90,6 +90,10 @@ etactica,eg200) ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0" ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33" ;; +glinet,6408|\ +glinet,6416) + ucidef_set_led_netdev "lan" "LAN" "gl-inet:green:lan" "eth0" + ;; glinet,gl-ar150) ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1" ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x02" diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 4f45b122ce..1bc7b2d68e 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -567,6 +567,32 @@ define Device/etactica_eg200 endef TARGET_DEVICES += etactica_eg200 +define Device/glinet_6408 + $(Device/tplink-8mlzma) + SOC := ar9331 + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := 6408 + DEVICE_PACKAGES := kmod-usb2 + IMAGE_SIZE := 8000k + TPLINK_HWID := 0x08000001 + IMAGES := sysupgrade.bin + SUPPORTED_DEVICES += gl-inet +endef +TARGET_DEVICES += glinet_6408 + +define Device/glinet_6416 + $(Device/tplink-16mlzma) + SOC := ar9331 + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := 6416 + DEVICE_PACKAGES := kmod-usb2 + IMAGE_SIZE := 16192k + TPLINK_HWID := 0x08000001 + IMAGES := sysupgrade.bin + SUPPORTED_DEVICES += gl-inet +endef +TARGET_DEVICES += glinet_6416 + define Device/glinet_gl-ar150 SOC := ar9330 DEVICE_VENDOR := GL.iNet