From: Biwen Li Date: Tue, 31 Dec 2019 07:33:44 +0000 (+0800) Subject: dm: arm: ls1021a: add i2c DM support X-Git-Tag: v2020.04-rc2~16^2~7 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=9ebde8849a37beff5eccb462a991e05b07f8a360;p=oweals%2Fu-boot.git dm: arm: ls1021a: add i2c DM support This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1021A Signed-off-by: Biwen Li Signed-off-by: Priyanka Jain --- diff --git a/board/freescale/common/dcu_sii9022a.c b/board/freescale/common/dcu_sii9022a.c index 3bf71abf55..832ae258f1 100644 --- a/board/freescale/common/dcu_sii9022a.c +++ b/board/freescale/common/dcu_sii9022a.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP */ #include @@ -63,7 +64,101 @@ int dcu_set_dvi_encoder(struct fb_videomode *videomode) u8 temp; u16 temp1, temp2; u32 temp3; +#ifdef CONFIG_DM_I2C + struct udevice *dev; + int ret; + + ret = i2c_get_chip_for_busnum(CONFIG_SYS_I2C_DVI_BUS_NUM, + CONFIG_SYS_I2C_DVI_ADDR, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + CONFIG_SYS_I2C_DVI_BUS_NUM); + return ret; + } + /* Enable TPI transmitter mode */ + temp = TPI_TRANS_MODE_ENABLE; + dm_i2c_write(dev, TPI_TRANS_MODE_REG, &temp, 1); + + /* Enter into D0 state, full operation */ + dm_i2c_read(dev, TPI_PWR_STAT_REG, &temp, 1); + temp &= ~TPI_PWR_STAT_MASK; + temp |= TPI_PWR_STAT_D0; + dm_i2c_write(dev, TPI_PWR_STAT_REG, &temp, 1); + + /* Enable source termination */ + temp = TPI_SET_PAGE_SII9022A; + dm_i2c_write(dev, TPI_SET_PAGE_REG, &temp, 1); + temp = TPI_SET_OFFSET_SII9022A; + dm_i2c_write(dev, TPI_SET_OFFSET_REG, &temp, 1); + + dm_i2c_read(dev, TPI_RW_ACCESS_REG, &temp, 1); + temp |= TPI_RW_EN_SRC_TERMIN; + dm_i2c_write(dev, TPI_RW_ACCESS_REG, &temp, 1); + + /* Set TPI system control */ + temp = TPI_SYS_TMDS_OUTPUT | TPI_SYS_AV_NORAML | TPI_SYS_DVI_MODE; + dm_i2c_write(dev, TPI_SYS_CTRL_REG, &temp, 1); + + /* Set pixel clock */ + temp1 = PICOS2KHZ(videomode->pixclock) / 10; + temp = (u8)(temp1 & 0xFF); + dm_i2c_write(dev, PIXEL_CLK_LSB_REG, &temp, 1); + temp = (u8)(temp1 >> 8); + dm_i2c_write(dev, PIXEL_CLK_MSB_REG, &temp, 1); + + /* Set total pixels per line */ + temp1 = videomode->hsync_len + videomode->left_margin + + videomode->xres + videomode->right_margin; + temp = (u8)(temp1 & 0xFF); + dm_i2c_write(dev, TOTAL_PIXELS_LSB_REG, &temp, 1); + temp = (u8)(temp1 >> 8); + dm_i2c_write(dev, TOTAL_PIXELS_MSB_REG, &temp, 1); + + /* Set total lines */ + temp2 = videomode->vsync_len + videomode->upper_margin + + videomode->yres + videomode->lower_margin; + temp = (u8)(temp2 & 0xFF); + dm_i2c_write(dev, TOTAL_LINES_LSB_REG, &temp, 1); + temp = (u8)(temp2 >> 8); + dm_i2c_write(dev, TOTAL_LINES_MSB_REG, &temp, 1); + + /* Set vertical frequency in Hz */ + temp3 = temp1 * temp2; + temp3 = (PICOS2KHZ(videomode->pixclock) * 1000) / temp3; + temp1 = (u16)temp3 * 100; + temp = (u8)(temp1 & 0xFF); + dm_i2c_write(dev, VERT_FREQ_LSB_REG, &temp, 1); + temp = (u8)(temp1 >> 8); + dm_i2c_write(dev, VERT_FREQ_MSB_REG, &temp, 1); + + /* Set TPI input bus and pixel repetition data */ + temp = TPI_INBUS_CLOCK_RATIO_1 | TPI_INBUS_FULL_PIXEL_WIDE | + TPI_INBUS_RISING_EDGE; + dm_i2c_write(dev, TPI_INBUS_FMT_REG, &temp, 1); + + /* Set TPI AVI Input format data */ + temp = TPI_INPUT_CLR_DEPTH_8BIT | TPI_INPUT_VRANGE_EXPAN_AUTO | + TPI_INPUT_CLR_RGB; + dm_i2c_write(dev, TPI_INPUT_FMT_REG, &temp, 1); + + /* Set TPI AVI Output format data */ + temp = TPI_OUTPUT_CLR_DEPTH_8BIT | TPI_OUTPUT_VRANGE_COMPRE_AUTO | + TPI_OUTPUT_CLR_HDMI_RGB; + dm_i2c_write(dev, TPI_OUTPUT_FMT_REG, &temp, 1); + + /* Set TPI audio configuration write data */ + temp = TPI_AUDIO_PASS_BASIC; + dm_i2c_write(dev, TPI_AUDIO_HANDING_REG, &temp, 1); + + temp = TPI_AUDIO_INTF_I2S | TPI_AUDIO_INTF_NORMAL | + TPI_AUDIO_TYPE_PCM; + dm_i2c_write(dev, TPI_AUDIO_INTF_REG, &temp, 1); + + temp = TPI_AUDIO_SAMP_SIZE_16BIT | TPI_AUDIO_SAMP_FREQ_44K; + dm_i2c_write(dev, TPI_AUDIO_FREQ_REG, &temp, 1); +#else i2c_set_bus_num(CONFIG_SYS_I2C_DVI_BUS_NUM); /* Enable TPI transmitter mode */ @@ -147,6 +242,7 @@ int dcu_set_dvi_encoder(struct fb_videomode *videomode) temp = TPI_AUDIO_SAMP_SIZE_16BIT | TPI_AUDIO_SAMP_FREQ_44K; i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_AUDIO_FREQ_REG, 1, &temp, 1); +#endif return 0; } diff --git a/board/freescale/common/diu_ch7301.c b/board/freescale/common/diu_ch7301.c index 435b4a3f1a..7f11123e6f 100644 --- a/board/freescale/common/diu_ch7301.c +++ b/board/freescale/common/diu_ch7301.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP * Authors: Priyanka Jain * Wang Dongsheng * @@ -51,6 +52,85 @@ int diu_set_dvi_encoder(unsigned int pixclock) u8 temp; temp = I2C_DVI_TEST_PATTERN_VAL; +#ifdef CONFIG_DM_I2C + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(CONFIG_SYS_I2C_DVI_BUS_NUM, + CONFIG_SYS_I2C_DVI_ADDR, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + CONFIG_SYS_I2C_DVI_BUS_NUM); + return ret; + } + ret = dm_i2c_write(dev, I2C_DVI_TEST_PATTERN_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select proper dvi test pattern\n"); + return ret; + } + temp = I2C_DVI_INPUT_DATA_FORMAT_VAL; + ret = dm_i2c_write(dev, I2C_DVI_INPUT_DATA_FORMAT_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi input data format\n"); + return ret; + } + + /* Set Sync polarity register */ + temp = I2C_DVI_SYNC_POLARITY_VAL; + ret = dm_i2c_write(dev, I2C_DVI_SYNC_POLARITY_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi syc polarity\n"); + return ret; + } + + /* Set PLL registers based on pixel clock rate*/ + if (pixclock > 65000000) { + temp = I2C_DVI_PLL_CHARGE_CNTL_HIGH_SPEED_VAL; + ret = dm_i2c_write(dev, I2C_DVI_PLL_CHARGE_CNTL_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll charge_cntl\n"); + return ret; + } + temp = I2C_DVI_PLL_DIVIDER_HIGH_SPEED_VAL; + ret = dm_i2c_write(dev, I2C_DVI_PLL_DIVIDER_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll divider\n"); + return ret; + } + temp = I2C_DVI_PLL_FILTER_HIGH_SPEED_VAL; + ret = dm_i2c_write(dev, I2C_DVI_PLL_FILTER_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll filter\n"); + return ret; + } + } else { + temp = I2C_DVI_PLL_CHARGE_CNTL_LOW_SPEED_VAL; + ret = dm_i2c_write(dev, I2C_DVI_PLL_CHARGE_CNTL_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll charge_cntl\n"); + return ret; + } + temp = I2C_DVI_PLL_DIVIDER_LOW_SPEED_VAL; + ret = dm_i2c_write(dev, I2C_DVI_PLL_DIVIDER_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll divider\n"); + return ret; + } + temp = I2C_DVI_PLL_FILTER_LOW_SPEED_VAL; + ret = dm_i2c_write(dev, I2C_DVI_PLL_FILTER_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll filter\n"); + return ret; + } + } + + temp = I2C_DVI_POWER_MGMT_VAL; + ret = dm_i2c_write(dev, I2C_DVI_POWER_MGMT_REG, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi power mgmt\n"); + return ret; + } +#else ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, I2C_DVI_TEST_PATTERN_REG, 1, &temp, 1); if (ret) { @@ -128,6 +208,7 @@ int diu_set_dvi_encoder(unsigned int pixclock) puts("I2C: failed to select dvi power mgmt\n"); return ret; } +#endif udelay(500); diff --git a/board/freescale/ls1021aqds/dcu.c b/board/freescale/ls1021aqds/dcu.c index c4eac5e302..b648a7872b 100644 --- a/board/freescale/ls1021aqds/dcu.c +++ b/board/freescale/ls1021aqds/dcu.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP * * FSL DCU Framebuffer driver */ @@ -15,11 +16,23 @@ DECLARE_GLOBAL_DATA_PTR; -static int select_i2c_ch_pca9547(u8 ch) +static int select_i2c_ch_pca9547(u8 ch, int bus_num) { int ret; +#ifdef CONFIG_DM_I2C + struct udevice *dev; + ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + ret = dm_i2c_write(dev, 0, &ch, 1); +#else ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); +#endif if (ret) { puts("PCA: failed to select proper channel\n"); return ret; @@ -51,6 +64,28 @@ int platform_dcu_init(struct fb_info *fbinfo, u8 ch; /* Mux I2C3+I2C4 as HSYNC+VSYNC */ +#ifdef CONFIG_DM_I2C + struct udevice *dev; + + /* QIXIS device mount on I2C1 bus*/ + ret = i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_QIXIS_ADDR, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + 0); + return ret; + } + ret = dm_i2c_read(dev, QIXIS_DCU_BRDCFG5, &ch, 1); + if (ret) { + printf("Error: failed to read I2C @%02x\n", + CONFIG_SYS_I2C_QIXIS_ADDR); + return ret; + } + ch &= 0x1F; + ch |= 0xA0; + ret = dm_i2c_write(dev, QIXIS_DCU_BRDCFG5, &ch, 1); + +#else ret = i2c_read(CONFIG_SYS_I2C_QIXIS_ADDR, QIXIS_DCU_BRDCFG5, 1, &ch, 1); if (ret) { @@ -62,6 +97,7 @@ int platform_dcu_init(struct fb_info *fbinfo, ch |= 0xA0; ret = i2c_write(CONFIG_SYS_I2C_QIXIS_ADDR, QIXIS_DCU_BRDCFG5, 1, &ch, 1); +#endif if (ret) { printf("Error: failed to write I2C @%02x\n", CONFIG_SYS_I2C_QIXIS_ADDR); @@ -76,10 +112,14 @@ int platform_dcu_init(struct fb_info *fbinfo, pixval = 1000000000 / dcu_fb_videomode->pixclock; pixval *= 1000; +#ifndef CONFIG_DM_I2C i2c_set_bus_num(CONFIG_SYS_I2C_DVI_BUS_NUM); - select_i2c_ch_pca9547(I2C_MUX_CH_CH7301); +#endif + select_i2c_ch_pca9547(I2C_MUX_CH_CH7301, + CONFIG_SYS_I2C_DVI_BUS_NUM); diu_set_dvi_encoder(pixval); - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, + CONFIG_SYS_I2C_DVI_BUS_NUM); } else { return 0; } diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index b7f8f1d578..1ae822e510 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP */ #include @@ -139,11 +140,23 @@ unsigned long get_board_ddr_clk(void) return 66666666; } -int select_i2c_ch_pca9547(u8 ch) +int select_i2c_ch_pca9547(u8 ch, int bus_num) { int ret; +#ifdef CONFIG_DM_I2C + struct udevice *dev; + ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + ret = dm_i2c_write(dev, 0, &ch, 1); +#else ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); +#endif if (ret) { puts("PCA: failed to select proper channel\n"); return ret; @@ -158,8 +171,10 @@ int dram_init(void) * When resuming from deep sleep, the I2C channel may not be * in the default channel. So, switch to the default channel * before accessing DDR SPD. + * + * PCA9547(0x77) mount on I2C1 bus */ - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); return fsl_initdram(); } @@ -408,7 +423,7 @@ int board_init(void) erratum_a009942_check_cpo(); #endif - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); #ifndef CONFIG_SYS_FSL_NO_SERDES fsl_serdes_init(); diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c index 497dce5f0f..d1ff7b8ba6 100644 --- a/board/freescale/ls1021atwr/ls1021atwr.c +++ b/board/freescale/ls1021atwr/ls1021atwr.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP */ #include @@ -447,14 +448,37 @@ void board_init_f(ulong dummy) /* program the regulator (MC34VR500) to support deep sleep */ void ls1twr_program_regulator(void) { - unsigned int i2c_bus; u8 i2c_device_id; #define LS1TWR_I2C_BUS_MC34VR500 1 #define MC34VR500_ADDR 0x8 #define MC34VR500_DEVICEID 0x4 #define MC34VR500_DEVICEID_MASK 0x0f +#ifdef CONFIG_DM_I2C + struct udevice *dev; + int ret; + + ret = i2c_get_chip_for_busnum(LS1TWR_I2C_BUS_MC34VR500, MC34VR500_ADDR, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + LS1TWR_I2C_BUS_MC34VR500); + return; + } + i2c_device_id = dm_i2c_reg_read(dev, 0x0) & + MC34VR500_DEVICEID_MASK; + if (i2c_device_id != MC34VR500_DEVICEID) { + printf("The regulator (MC34VR500) does not exist. The device does not support deep sleep.\n"); + return; + } + dm_i2c_reg_write(dev, 0x31, 0x4); + dm_i2c_reg_write(dev, 0x4d, 0x4); + dm_i2c_reg_write(dev, 0x6d, 0x38); + dm_i2c_reg_write(dev, 0x6f, 0x37); + dm_i2c_reg_write(dev, 0x71, 0x30); +#else + unsigned int i2c_bus; i2c_bus = i2c_get_bus_num(); i2c_set_bus_num(LS1TWR_I2C_BUS_MC34VR500); i2c_device_id = i2c_reg_read(MC34VR500_ADDR, 0x0) & @@ -471,6 +495,7 @@ void ls1twr_program_regulator(void) i2c_reg_write(MC34VR500_ADDR, 0x71, 0x30); i2c_set_bus_num(i2c_bus); +#endif } #endif diff --git a/configs/ls1021aiot_qspi_defconfig b/configs/ls1021aiot_qspi_defconfig index c3376e106c..8a3b79693b 100644 --- a/configs/ls1021aiot_qspi_defconfig +++ b/configs/ls1021aiot_qspi_defconfig @@ -45,3 +45,5 @@ CONFIG_FSL_QSPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aiot_sdcard_defconfig b/configs/ls1021aiot_sdcard_defconfig index a7a340076f..684ae4e75f 100644 --- a/configs/ls1021aiot_sdcard_defconfig +++ b/configs/ls1021aiot_sdcard_defconfig @@ -51,3 +51,5 @@ CONFIG_FSL_QSPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_ddr4_nor_defconfig b/configs/ls1021aqds_ddr4_nor_defconfig index 70f7053ed0..fdfec314e9 100644 --- a/configs/ls1021aqds_ddr4_nor_defconfig +++ b/configs/ls1021aqds_ddr4_nor_defconfig @@ -67,3 +67,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_ddr4_nor_lpuart_defconfig b/configs/ls1021aqds_ddr4_nor_lpuart_defconfig index eaa26ceee9..c0d9395f49 100644 --- a/configs/ls1021aqds_ddr4_nor_lpuart_defconfig +++ b/configs/ls1021aqds_ddr4_nor_lpuart_defconfig @@ -67,3 +67,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_nand_defconfig b/configs/ls1021aqds_nand_defconfig index c7c701de9e..0a9438039b 100644 --- a/configs/ls1021aqds_nand_defconfig +++ b/configs/ls1021aqds_nand_defconfig @@ -82,3 +82,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_nor_SECURE_BOOT_defconfig b/configs/ls1021aqds_nor_SECURE_BOOT_defconfig index 3f99035553..6b12a4e277 100644 --- a/configs/ls1021aqds_nor_SECURE_BOOT_defconfig +++ b/configs/ls1021aqds_nor_SECURE_BOOT_defconfig @@ -66,3 +66,5 @@ CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set CONFIG_RSA=y CONFIG_SPL_RSA=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_nor_defconfig b/configs/ls1021aqds_nor_defconfig index 6fe62a713d..9c35ba954f 100644 --- a/configs/ls1021aqds_nor_defconfig +++ b/configs/ls1021aqds_nor_defconfig @@ -68,3 +68,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_nor_lpuart_defconfig b/configs/ls1021aqds_nor_lpuart_defconfig index ad222eb9ef..39b82dd022 100644 --- a/configs/ls1021aqds_nor_lpuart_defconfig +++ b/configs/ls1021aqds_nor_lpuart_defconfig @@ -68,3 +68,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_qspi_defconfig b/configs/ls1021aqds_qspi_defconfig index e643242b14..ac5133896d 100644 --- a/configs/ls1021aqds_qspi_defconfig +++ b/configs/ls1021aqds_qspi_defconfig @@ -69,3 +69,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_sdcard_ifc_defconfig b/configs/ls1021aqds_sdcard_ifc_defconfig index 2c28b9efba..17b6e6418c 100644 --- a/configs/ls1021aqds_sdcard_ifc_defconfig +++ b/configs/ls1021aqds_sdcard_ifc_defconfig @@ -81,3 +81,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021aqds_sdcard_qspi_defconfig b/configs/ls1021aqds_sdcard_qspi_defconfig index d8065e7242..703eeff05d 100644 --- a/configs/ls1021aqds_sdcard_qspi_defconfig +++ b/configs/ls1021aqds_sdcard_qspi_defconfig @@ -81,3 +81,5 @@ CONFIG_USB_STORAGE=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atsn_qspi_defconfig b/configs/ls1021atsn_qspi_defconfig index c30e89d959..543f96580b 100644 --- a/configs/ls1021atsn_qspi_defconfig +++ b/configs/ls1021atsn_qspi_defconfig @@ -57,3 +57,5 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atsn_sdcard_defconfig b/configs/ls1021atsn_sdcard_defconfig index 3d3d743c87..6c73a9f4ee 100644 --- a/configs/ls1021atsn_sdcard_defconfig +++ b/configs/ls1021atsn_sdcard_defconfig @@ -68,3 +68,5 @@ CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_nor_SECURE_BOOT_defconfig b/configs/ls1021atwr_nor_SECURE_BOOT_defconfig index dbd9d0e070..2925f37a75 100644 --- a/configs/ls1021atwr_nor_SECURE_BOOT_defconfig +++ b/configs/ls1021atwr_nor_SECURE_BOOT_defconfig @@ -60,3 +60,5 @@ CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set CONFIG_RSA=y CONFIG_SPL_RSA=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_nor_defconfig b/configs/ls1021atwr_nor_defconfig index 7fcd4de2d0..cbcc491eb0 100644 --- a/configs/ls1021atwr_nor_defconfig +++ b/configs/ls1021atwr_nor_defconfig @@ -62,3 +62,5 @@ CONFIG_USB_XHCI_DWC3=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_nor_lpuart_defconfig b/configs/ls1021atwr_nor_lpuart_defconfig index 0303d49045..0b364dc85d 100644 --- a/configs/ls1021atwr_nor_lpuart_defconfig +++ b/configs/ls1021atwr_nor_lpuart_defconfig @@ -63,3 +63,5 @@ CONFIG_USB_XHCI_DWC3=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_qspi_defconfig b/configs/ls1021atwr_qspi_defconfig index 50b7eedcc2..077ccef5f1 100644 --- a/configs/ls1021atwr_qspi_defconfig +++ b/configs/ls1021atwr_qspi_defconfig @@ -67,3 +67,5 @@ CONFIG_USB_XHCI_DWC3=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_sdcard_ifc_SECURE_BOOT_defconfig b/configs/ls1021atwr_sdcard_ifc_SECURE_BOOT_defconfig index c909f40bd1..01c541399e 100644 --- a/configs/ls1021atwr_sdcard_ifc_SECURE_BOOT_defconfig +++ b/configs/ls1021atwr_sdcard_ifc_SECURE_BOOT_defconfig @@ -74,3 +74,5 @@ CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set CONFIG_RSA=y CONFIG_SPL_RSA=y +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_sdcard_ifc_defconfig b/configs/ls1021atwr_sdcard_ifc_defconfig index 97e6a4747f..abc5d873ff 100644 --- a/configs/ls1021atwr_sdcard_ifc_defconfig +++ b/configs/ls1021atwr_sdcard_ifc_defconfig @@ -75,3 +75,5 @@ CONFIG_USB_XHCI_DWC3=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/configs/ls1021atwr_sdcard_qspi_defconfig b/configs/ls1021atwr_sdcard_qspi_defconfig index 3ad24eae2f..7cc76aa3c6 100644 --- a/configs/ls1021atwr_sdcard_qspi_defconfig +++ b/configs/ls1021atwr_sdcard_qspi_defconfig @@ -78,3 +78,5 @@ CONFIG_USB_XHCI_DWC3=y CONFIG_VIDEO_FSL_DCU_FB=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set +CONFIG_DM_I2C=y +CONFIG_DM_GPIO=y diff --git a/include/configs/ls1021aiot.h b/include/configs/ls1021aiot.h index 0b2d331b9b..1d218aa703 100644 --- a/include/configs/ls1021aiot.h +++ b/include/configs/ls1021aiot.h @@ -1,6 +1,7 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2016 Freescale Semiconductor, Inc. + * Copyright 2019 NXP */ #ifndef __CONFIG_H @@ -97,7 +98,13 @@ * I2C */ #define CONFIG_CMD_I2C + +#ifndef CONFIG_DM_I2C #define CONFIG_SYS_I2C +#else +#define CONFIG_I2C_SET_DEFAULT_BUS_NUM +#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 +#endif #define CONFIG_SYS_I2C_MXC #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h index 8427be5adc..8bac2d2561 100644 --- a/include/configs/ls1021aqds.h +++ b/include/configs/ls1021aqds.h @@ -1,6 +1,7 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP */ #ifndef __CONFIG_H @@ -331,7 +332,12 @@ unsigned long get_board_ddr_clk(void); /* * I2C */ +#ifndef CONFIG_DM_I2C #define CONFIG_SYS_I2C +#else +#define CONFIG_I2C_SET_DEFAULT_BUS_NUM +#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 +#endif #define CONFIG_SYS_I2C_MXC #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ diff --git a/include/configs/ls1021atsn.h b/include/configs/ls1021atsn.h index bdb4273cf5..984df6249f 100644 --- a/include/configs/ls1021atsn.h +++ b/include/configs/ls1021atsn.h @@ -1,5 +1,5 @@ /* SPDX-License-Identifier: GPL-2.0 - * Copyright 2016-2018 NXP Semiconductors + * Copyright 2016-2019 NXP Semiconductors * Copyright 2019 Vladimir Oltean */ @@ -107,7 +107,12 @@ #define CONFIG_BAUDRATE 115200 /* I2C */ +#ifndef CONFIG_DM_I2C #define CONFIG_SYS_I2C +#else +#define CONFIG_I2C_SET_DEFAULT_BUS_NUM +#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 +#endif #define CONFIG_SYS_I2C_MXC #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h index 1919d1e14f..bec55a78af 100644 --- a/include/configs/ls1021atwr.h +++ b/include/configs/ls1021atwr.h @@ -1,6 +1,7 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2019 NXP */ #ifndef __CONFIG_H @@ -209,7 +210,12 @@ /* * I2C */ +#ifndef CONFIG_DM_I2C #define CONFIG_SYS_I2C +#else +#define CONFIG_I2C_SET_DEFAULT_BUS_NUM +#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 +#endif #define CONFIG_SYS_I2C_MXC #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ @@ -446,6 +452,7 @@ #ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#undef CONFIG_DM_I2C #else #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif