From: Masahiro Yamada Date: Thu, 30 Oct 2014 09:28:01 +0000 (+0900) Subject: Remove unused files X-Git-Tag: v2015.01-rc1~51^2~3 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=9ea7f3a6d8d0ef9f618e0cb0b785c00cfd5f3183;p=oweals%2Fu-boot.git Remove unused files [1] arch/arm/include/asm/arch-at91/at91_shdwn.h The top9000 was the last board to use this header file. It was removed by commit d58a9451e733 (ppc/arm: zap EMK boards). [2] board/matrix_vision/common/* Some Matrix Vision boards were dropped by commit e7a565638a7a (powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7) and commit af55e35d3389 (powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR). Since then these files have been unused. [3] include/usb/omap1510_udc.h The omap5912osk was the last board to use this header file. It was removed by commit 62d636aa2ac2 (omap: remove omap5912osk board support). Signed-off-by: Masahiro Yamada Acked-By: Wolfgang Denk --- diff --git a/arch/arm/include/asm/arch-at91/at91_shdwn.h b/arch/arm/include/asm/arch-at91/at91_shdwn.h deleted file mode 100644 index 18d9ea690e..0000000000 --- a/arch/arm/include/asm/arch-at91/at91_shdwn.h +++ /dev/null @@ -1,35 +0,0 @@ -/* - * Copyright (C) 2010 - * Reinhard Meyer, reinhard.meyer@emk-elektronik.de - * - * Shutdown Controller - * Based on AT91SAM9XE datasheet - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef AT91_SHDWN_H -#define AT91_SHDWN_H - -#ifndef __ASSEMBLY__ - -struct at91_shdwn { - u32 cr; /* Control Rer. WO */ - u32 mr; /* Mode Register RW 0x00000003 */ - u32 sr; /* Status Register RO 0x00000000 */ -}; - -#endif /* __ASSEMBLY__ */ - -#define AT91_SHDW_CR_KEY 0xa5000000 -#define AT91_SHDW_CR_SHDW 0x00000001 - -#define AT91_SHDW_MR_RTTWKEN 0x00010000 -#define AT91_SHDW_MR_CPTWK0 0x000000f0 -#define AT91_SHDW_MR_WKMODE0H2L 0x00000002 -#define AT91_SHDW_MR_WKMODE0L2H 0x00000001 - -#define AT91_SHDW_SR_RTTWK 0x00010000 -#define AT91_SHDW_SR_WAKEUP0 0x00000001 - -#endif diff --git a/board/matrix_vision/common/Makefile b/board/matrix_vision/common/Makefile deleted file mode 100644 index 699da1ca27..0000000000 --- a/board/matrix_vision/common/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = mv_common.o diff --git a/board/matrix_vision/common/mv_common.c b/board/matrix_vision/common/mv_common.c deleted file mode 100644 index 1be5aba2e9..0000000000 --- a/board/matrix_vision/common/mv_common.c +++ /dev/null @@ -1,112 +0,0 @@ -/* - * (C) Copyright 2008 - * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#ifndef CONFIG_ENV_IS_NOWHERE -static char* entries_to_keep[] = { - "serial#", "ethaddr", "eth1addr", "model_info", "sensor_cnt", - "fpgadatasize", "ddr_size", "use_dhcp", "use_static_ipaddr", - "static_ipaddr", "static_netmask", "static_gateway", - "syslog", "watchdog", "netboot", "evo8serialnumber" }; - -#define MV_MAX_ENV_ENTRY_LENGTH 64 -#define MV_KEEP_ENTRIES ARRAY_SIZE(entries_to_keep) - -void mv_reset_environment(void) -{ - int i; - char *s[MV_KEEP_ENTRIES]; - char entries[MV_KEEP_ENTRIES][MV_MAX_ENV_ENTRY_LENGTH]; - - printf("\n*** RESET ENVIRONMENT ***\n"); - - memset(entries, 0, MV_KEEP_ENTRIES * MV_MAX_ENV_ENTRY_LENGTH); - for (i = 0; i < MV_KEEP_ENTRIES; i++) { - s[i] = getenv(entries_to_keep[i]); - if (s[i]) { - printf("save '%s' : %s\n", entries_to_keep[i], s[i]); - strncpy(entries[i], s[i], MV_MAX_ENV_ENTRY_LENGTH); - } - } - - gd->env_valid = 0; - env_relocate(); - - for (i = 0; i < MV_KEEP_ENTRIES; i++) { - if (s[i]) { - printf("restore '%s' : %s\n", entries_to_keep[i], s[i]); - setenv(entries_to_keep[i], s[i]); - } - } - - saveenv(); -} -#endif - -int mv_load_fpga(void) -{ - int result; - size_t data_size = 0; - void *fpga_data = NULL; - char *datastr = getenv("fpgadata"); - char *sizestr = getenv("fpgadatasize"); - - if (getenv("skip_fpga")) { - printf("found 'skip_fpga' -> FPGA _not_ loaded !\n"); - return -1; - } - printf("loading FPGA\n"); - - if (datastr) - fpga_data = (void *)simple_strtoul(datastr, NULL, 16); - if (sizestr) - data_size = (size_t)simple_strtoul(sizestr, NULL, 16); - if (!data_size) { - printf("fpgadatasize invalid -> FPGA _not_ loaded !\n"); - return -1; - } - - result = fpga_load(0, fpga_data, data_size, BIT_FULL); - if (!result) - bootstage_mark(BOOTSTAGE_ID_START); - - return result; -} - -u8 *dhcp_vendorex_prep(u8 *e) -{ - char *ptr; - - /* DHCP vendor-class-identifier = 60 */ - if ((ptr = getenv("dhcp_vendor-class-identifier"))) { - *e++ = 60; - *e++ = strlen(ptr); - while (*ptr) - *e++ = *ptr++; - } - /* DHCP_CLIENT_IDENTIFIER = 61 */ - if ((ptr = getenv("dhcp_client_id"))) { - *e++ = 61; - *e++ = strlen(ptr); - while (*ptr) - *e++ = *ptr++; - } - - return e; -} - -u8 *dhcp_vendorex_proc(u8 *popt) -{ - return NULL; -} diff --git a/board/matrix_vision/common/mv_common.h b/board/matrix_vision/common/mv_common.h deleted file mode 100644 index 369394356c..0000000000 --- a/board/matrix_vision/common/mv_common.h +++ /dev/null @@ -1,9 +0,0 @@ -/* - * Copyright 2008 Matrix Vision GmbH - * - * SPDX-License-Identifier: GPL-2.0+ - */ - - -extern int mv_load_fpga(void); -extern void mv_reset_environment(void); diff --git a/include/usb/omap1510_udc.h b/include/usb/omap1510_udc.h deleted file mode 100644 index adfbf54996..0000000000 --- a/include/usb/omap1510_udc.h +++ /dev/null @@ -1,174 +0,0 @@ -/* - * (C) Copyright 2003 - * Gerry Hamel, geh@ti.com, Texas Instruments - * - * Based on - * linux/drivers/usb/device/bi/omap.h - * Register definitions for TI OMAP1510 USB bus interface driver - * - * Author: MontaVista Software, Inc. - * source@mvista.com - * - * 2003 (c) MontaVista Software, Inc. This file is licensed under - * the terms of the GNU General Public License version 2. This program - * is licensed "as is" without any warranty of any kind, whether express - * or implied. - */ - -#ifndef __USBDCORE_OMAP1510_H__ -#define __USBDCORE_OMAP1510_H__ - - -/* - * 13.2 MPU Register Map - */ - -/* Table 13-1. USB Function Module Registers (endpoint) */ -#define UDC_BASE 0xFFFB4000 -#define UDC_OFFSET(offset) (UDC_BASE + (offset)) -#define UDC_REV UDC_OFFSET(0x0) /* Revision */ -#define UDC_EP_NUM UDC_OFFSET(0x4) /* Endpoint selection */ -#define UDC_DATA UDC_OFFSET(0x08) /* Data */ -#define UDC_CTRL UDC_OFFSET(0x0C) /* Control */ -#define UDC_STAT_FLG UDC_OFFSET(0x10) /* Status flag */ -#define UDC_RXFSTAT UDC_OFFSET(0x14) /* Receive FIFO status */ -#define UDC_SYSCON1 UDC_OFFSET(0x18) /* System configuration 1 */ -#define UDC_SYSCON2 UDC_OFFSET(0x1C) /* System configuration 2 */ -#define UDC_DEVSTAT UDC_OFFSET(0x20) /* Device status */ -#define UDC_SOF UDC_OFFSET(0x24) /* Start of frame */ -#define UDC_IRQ_EN UDC_OFFSET(0x28) /* Interrupt enable */ -#define UDC_DMA_IRQ_EN UDC_OFFSET(0x2C) /* DMA interrupt enable */ -#define UDC_IRQ_SRC UDC_OFFSET(0x30) /* Interrupt source */ -#define UDC_EPN_STAT UDC_OFFSET(0x34) /* Endpoint interrupt status */ -#define UDC_DMAN_STAT UDC_OFFSET(0x3C) /* DMA endpoint interrupt status */ - -/* IRQ_EN register fields */ -#define UDC_Sof_IE (1 << 7) /* Start-of-frame interrupt enabled */ -#define UDC_EPn_RX_IE (1 << 5) /* Receive endpoint interrupt enabled */ -#define UDC_EPn_TX_IE (1 << 4) /* Transmit endpoint interrupt enabled */ -#define UDC_DS_Chg_IE (1 << 3) /* Device state changed interrupt enabled */ -#define UDC_EP0_IE (1 << 0) /* EP0 transaction interrupt enabled */ - -/* IRQ_SRC register fields */ -#define UDC_TXn_Done (1 << 10) /* Transmit DMA channel n done */ -#define UDC_RXn_Cnt (1 << 9) /* Receive DMA channel n transactions count */ -#define UDC_RXn_EOT (1 << 8) /* Receive DMA channel n end of transfer */ -#define UDC_SOF_Flg (1 << 7) /* Start-of-frame interrupt flag */ -#define UDC_EPn_RX (1 << 5) /* Endpoint n OUT transaction */ -#define UDC_EPn_TX (1 << 4) /* Endpoint n IN transaction */ -#define UDC_DS_Chg (1 << 3) /* Device state changed */ -#define UDC_Setup (1 << 2) /* Setup transaction */ -#define UDC_EP0_RX (1 << 1) /* EP0 OUT transaction */ -#define UDC_EP0_TX (1 << 0) /* EP0 IN transaction */ - -/* DEVSTAT register fields, 14.2.9 */ -#define UDC_R_WK_OK (1 << 6) /* Remote wakeup granted */ -#define UDC_USB_Reset (1 << 5) /* USB reset signalling is active */ -#define UDC_SUS (1 << 4) /* Suspended state */ -#define UDC_CFG (1 << 3) /* Configured state */ -#define UDC_ADD (1 << 2) /* Addressed state */ -#define UDC_DEF (1 << 1) /* Default state */ -#define UDC_ATT (1 << 0) /* Attached state */ - -/* SYSCON1 register fields */ -#define UDC_Cfg_Lock (1 << 8) /* Device configuration locked */ -#define UDC_Nak_En (1 << 4) /* NAK enable */ -#define UDC_Self_Pwr (1 << 2) /* Device is self-powered */ -#define UDC_Soff_Dis (1 << 1) /* Shutoff disabled */ -#define UDC_Pullup_En (1 << 0) /* External pullup enabled */ - -/* SYSCON2 register fields */ -#define UDC_Rmt_Wkp (1 << 6) /* Remote wakeup */ -#define UDC_Stall_Cmd (1 << 5) /* Stall endpoint */ -#define UDC_Dev_Cfg (1 << 3) /* Device configured */ -#define UDC_Clr_Cfg (1 << 2) /* Clear configured */ - -/* - * Select and enable endpoints - */ - -/* Table 13-1. USB Function Module Registers (endpoint configuration) */ -#define UDC_EPBASE UDC_OFFSET(0x80) /* Endpoints base address */ -#define UDC_EP0 UDC_EPBASE /* Control endpoint configuration */ -#define UDC_EP_RX_BASE UDC_OFFSET(0x84) /* Receive endpoints base address */ -#define UDC_EP_RX(endpoint) (UDC_EP_RX_BASE + ((endpoint) - 1) * 4) -#define UDC_EP_TX_BASE UDC_OFFSET(0xC4) /* Transmit endpoints base address */ -#define UDC_EP_TX(endpoint) (UDC_EP_TX_BASE + ((endpoint) - 1) * 4) - -/* EP_NUM register fields */ -#define UDC_Setup_Sel (1 << 6) /* Setup FIFO select */ -#define UDC_EP_Sel (1 << 5) /* TX/RX FIFO select */ -#define UDC_EP_Dir (1 << 4) /* Endpoint direction */ - -/* CTRL register fields */ -#define UDC_Clr_Halt (1 << 7) /* Clear halt endpoint */ -#define UDC_Set_Halt (1 << 6) /* Set halt endpoint */ -#define UDC_Set_FIFO_En (1 << 2) /* Set FIFO enable */ -#define UDC_Clr_EP (1 << 1) /* Clear endpoint */ -#define UDC_Reset_EP (1 << 0) /* Reset endpoint */ - -/* STAT_FLG register fields */ -#define UDC_Miss_In (1 << 14) -#define UDC_Data_Flush (1 << 13) -#define UDC_ISO_Err (1 << 12) -#define UDC_ISO_FIFO_Empty (1 << 9) -#define UDC_ISO_FIFO_Full (1 << 8) -#define UDC_EP_Halted (1 << 6) -#define UDC_STALL (1 << 5) -#define UDC_NAK (1 << 4) -#define UDC_ACK (1 << 3) -#define UDC_FIFO_En (1 << 2) -#define UDC_Non_ISO_FIFO_Empty (1 << 1) -#define UDC_Non_ISO_FIFO_Full (1 << 0) - -/* EPn_RX register fields */ -#define UDC_EPn_RX_Valid (1 << 15) /* valid */ -#define UDC_EPn_RX_Db (1 << 14) /* double-buffer */ -#define UDC_EPn_RX_Iso (1 << 11) /* isochronous */ - -/* EPn_TX register fields */ -#define UDC_EPn_TX_Valid (1 << 15) /* valid */ -#define UDC_EPn_TX_Db (1 << 14) /* double-buffer */ -#define UDC_EPn_TX_Iso (1 << 11) /* isochronous */ - -#define EP0_PACKETSIZE 0x40 - -/* physical to logical endpoint mapping - * Physical endpoints are an index into device->bus->endpoint_array. - * Logical endpoints are endpoints 0 to 15 IN and OUT as defined in - * the USB specification. - * - * physical ep logical ep direction endpoint_address - * 0 0 IN and OUT 0x00 - * 1 to 15 1 to 15 OUT 0x01 to 0x0f - * 16 to 30 1 to 15 IN 0x81 to 0x8f - */ -#define PHYS_EP_TO_EP_ADDR(ep) (((ep) < 16) ? (ep) : (((ep) - 15) | 0x80)) -#define EP_ADDR_TO_PHYS_EP(a) (((a) & 0x80) ? (((a) & ~0x80) + 15) : (a)) - -/* MOD_CONF_CTRL_0 bits (FIXME: move to board hardware.h ?) */ -#define CONF_MOD_USB_W2FC_VBUS_MODE_R (1 << 17) - -/* Other registers (may be) related to USB */ - -#define CLOCK_CTRL (0xFFFE0830) -#define APLL_CTRL (0xFFFE084C) -#define DPLL_CTRL (0xFFFE083C) -#define SOFT_REQ (0xFFFE0834) -#define STATUS_REQ (0xFFFE0840) - -/* FUNC_MUX_CTRL_0 bits related to USB */ -#define UDC_VBUS_CTRL (1 << 19) -#define UDC_VBUS_MODE (1 << 18) - -/* OMAP Endpoint parameters */ -#define UDC_OUT_PACKET_SIZE 64 -#define UDC_IN_PACKET_SIZE 64 -#define UDC_INT_PACKET_SIZE 16 -#define UDC_BULK_PACKET_SIZE 16 - -#define UDC_INT_ENDPOINT 5 -#define UDC_OUT_ENDPOINT 2 -#define UDC_IN_ENDPOINT 1 - -#endif