From: Dirk Eibach Date: Wed, 11 Jan 2017 15:00:45 +0000 (+0100) Subject: pci: mvebu: Fix Armada 38x support X-Git-Tag: v2017.03-rc2~119^2~12 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=882d3fa6dd588d100ba446e944022e6b7c9480ae;p=oweals%2Fu-boot.git pci: mvebu: Fix Armada 38x support Armada 38x has four PCI ports, not three. The optimization in pci_init_board() seems to assume that every port has three lanes. This is obviously wrong, and breaks support for Armada 38x. Signed-off-by: Dirk Eibach Signed-off-by: Mario Six Reviewed-by: Stefan Roese Signed-off-by: Stefan Roese --- diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h index 0f69f3341b..0900e4008c 100644 --- a/arch/arm/mach-mvebu/include/mach/soc.h +++ b/arch/arm/mach-mvebu/include/mach/soc.h @@ -67,6 +67,7 @@ #define MVEBU_REG_PCIE_BASE (MVEBU_REGISTER(0x40000)) #define MVEBU_AXP_USB_BASE (MVEBU_REGISTER(0x50000)) #define MVEBU_USB20_BASE (MVEBU_REGISTER(0x58000)) +#define MVEBU_REG_PCIE0_BASE (MVEBU_REGISTER(0x80000)) #define MVEBU_AXP_SATA_BASE (MVEBU_REGISTER(0xa0000)) #define MVEBU_SATA0_BASE (MVEBU_REGISTER(0xa8000)) #define MVEBU_NAND_BASE (MVEBU_REGISTER(0xd0000)) diff --git a/drivers/pci/pci_mvebu.c b/drivers/pci/pci_mvebu.c index 0f449703de..da0aa29865 100644 --- a/drivers/pci/pci_mvebu.c +++ b/drivers/pci/pci_mvebu.c @@ -91,25 +91,26 @@ static void __iomem *mvebu_pcie_membase = (void __iomem *)MBUS_PCI_MEM_BASE; #if defined(CONFIG_ARMADA_38X) #define PCIE_BASE(if) \ ((if) == 0 ? \ - MVEBU_REG_PCIE_BASE + 0x40000 : \ - MVEBU_REG_PCIE_BASE + 0x4000 * (if)) + MVEBU_REG_PCIE0_BASE : \ + (MVEBU_REG_PCIE_BASE + 0x4000 * (if - 1))) /* * On A38x MV6820 these PEX ports are supported: * 0 - Port 0.0 - * 1 - Port 0.1 - * 2 - Port 0.2 + * 1 - Port 1.0 + * 2 - Port 2.0 + * 3 - Port 3.0 */ -#define MAX_PEX 3 +#define MAX_PEX 4 static struct mvebu_pcie pcie_bus[MAX_PEX]; static void mvebu_get_port_lane(struct mvebu_pcie *pcie, int pex_idx, int *mem_target, int *mem_attr) { - u8 port[] = { 0, 1, 2 }; - u8 lane[] = { 0, 0, 0 }; - u8 target[] = { 8, 4, 4 }; - u8 attr[] = { 0xe8, 0xe8, 0xd8 }; + u8 port[] = { 0, 1, 2, 3 }; + u8 lane[] = { 0, 0, 0, 0 }; + u8 target[] = { 8, 4, 4, 4 }; + u8 attr[] = { 0xe8, 0xe8, 0xd8, 0xb8 }; pcie->port = port[pex_idx]; pcie->lane = lane[pex_idx]; @@ -351,9 +352,9 @@ void pci_init_board(void) mvebu_get_port_lane(pcie, i, &mem_target, &mem_attr); /* Don't read at all from pci registers if port power is down */ - if (pcie->lane == 0 && SELECT(soc_ctrl, pcie->port) == 0) { - i += 3; - debug("%s: skipping port %d\n", __func__, pcie->port); + if (SELECT(soc_ctrl, pcie->port) == 0) { + if (pcie->lane == 0) + debug("%s: skipping port %d\n", __func__, pcie->port); continue; }