From: Prafulla Wadaskar Date: Mon, 18 May 2009 20:10:16 +0000 (+0530) Subject: Marvell MV88E61XX Switch Driver support X-Git-Tag: v2009.08-rc1~130^2^2~9 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=6f51deb7f298413cfcb0a36d24c97ef7dd69d48f;p=oweals%2Fu-boot.git Marvell MV88E61XX Switch Driver support Chips supported:- 1. 88E6161 6 port gbe swtich with 5 integrated PHYs 2. 88E6165 6 port gbe swtich with 5 integrated PHYs 2. 88E6132 3 port gbe swtich with 2 integrated PHYs Platform specific configuration supported for:- default or router port vlan configuration led_init configuration mdip/n polarity reversal configuration Note: This driver is supported and tested against kirkwood egiga interface Contributors: Yotam Admon Michael Blostein Signed-off-by: Prafulla Wadaskar Signed-off-by: Ben Warren --- diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index 4fe3b05212..3b92614ac7 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -26,6 +26,7 @@ include $(TOPDIR)/config.mk LIB := $(obj)libphy.a COBJS-$(CONFIG_BITBANGMII) += miiphybb.o +COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c new file mode 100644 index 0000000000..ec47286ddd --- /dev/null +++ b/drivers/net/phy/mv88e61xx.c @@ -0,0 +1,413 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor + * Prafulla Wadaskar + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include +#include +#include "mv88e61xx.h" + +#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE +/* Chip Address mode + * The Switch support two modes of operation + * 1. single chip mode and + * 2. Multi-chip mode + * Refer section 9.2 &9.3 in chip datasheet-02 for more details + * + * By default single chip mode is configured + * multichip mode operation can be configured in board header + */ +static int mv88e61xx_busychk_multic(u32 devaddr) +{ + u32 reg = 0; + u32 timeout = MV88E61XX_PHY_TIMEOUT; + + /* Poll till SMIBusy bit is clear */ + do { + miiphy_read(name, devaddr, 0x0, ®); + if (timeout-- == 0) { + printf("SMI busy timeout\n"); + return -1; + } + } while (reg & (1 << 15)); + return 0; +} + +static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data) +{ + u16 reg; + u32 mii_dev_addr; + + /* command to read PHY dev address */ + if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) { + printf("Error..could not read PHY dev address\n"); + return; + } + mv88e61xx_busychk_multic(mii_dev_addr); + /* Write data to Switch indirect data register */ + miiphy_write(name, mii_dev_addr, 0x1, data); + /* Write command to Switch indirect command register (write) */ + miiphy_write(name, mii_dev_addr, 0x0, + reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 << + 15)); +} + +static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data) +{ + u16 reg; + u32 mii_dev_addr; + + /* command to read PHY dev address */ + if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) { + printf("Error..could not read PHY dev address\n"); + return; + } + mv88e61xx_busychk_multic(mii_dev_addr); + /* Write command to Switch indirect command register (read) */ + miiphy_write(name, mii_dev_addr, 0x0, + reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 << + 15)); + mv88e61xx_busychk_multic(mii_dev_addr); + /* Read data from Switch indirect data register */ + miiphy_read(name, mii_dev_addr, 0x1, (u16 *) & data); +} +#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */ + +static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig, + u32 max_prtnum, u32 ports_ofs) +{ + u32 prt; + u16 reg; + char *name = swconfig->name; + u32 cpu_port = swconfig->cpuport; + u32 port_mask = swconfig->ports_enabled; + enum mv88e61xx_cfg_vlan vlancfg = swconfig->vlancfg; + + /* be sure all ports are disabled */ + for (prt = 0; prt < max_prtnum; prt++) { + RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, ®); + reg &= ~0x3; + WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, reg); + + if (!(cpu_port & (1 << prt))) + continue; + /* Set CPU port VID to 0x1 */ + RD_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, ®); + reg &= ~0xfff; + reg |= 0x1; + WR_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, reg); + } + + /* Setting Port default priority for all ports to zero */ + for (prt = 0; prt < max_prtnum; prt++) { + RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, ®); + reg &= ~0xc000; + WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, reg); + } + /* Setting VID and VID map for all ports except CPU port */ + for (prt = 0; prt < max_prtnum; prt++) { + /* only for enabled ports */ + if ((1 << prt) & port_mask) { + /* skip CPU port */ + if ((1 << prt) & cpu_port) { + /* + * Set Vlan map table for cpu_port to see + * all ports + */ + RD_PHY(name, (ports_ofs + prt), + MV88E61XX_PRT_VMAP_REG, ®); + reg &= ~((1 << max_prtnum) - 1); + reg |= port_mask & ~(1 << prt); + WR_PHY(name, (ports_ofs + prt), + MV88E61XX_PRT_VMAP_REG, reg); + } else { + + /* + * set Ports VLAN Mapping. + * port prt <--> cpu_port VLAN #prt+1. + */ + RD_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_VID_REG, ®); + reg &= ~0x0fff; + reg |= (prt + 1); + WR_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_VID_REG, reg); + + RD_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_VMAP_REG, ®); + if (vlancfg == MV88E61XX_VLANCFG_DEFAULT) { + /* + * all any port can send frames to all other ports + * ref: sec 3.2.1.1 of datasheet + */ + reg |= 0x03f; + reg &= ~(1 << prt); + } else if (vlancfg == MV88E61XX_VLANCFG_ROUTER) { + /* + * all other ports can send frames to CPU port only + * ref: sec 3.2.1.2 of datasheet + */ + reg &= ~((1 << max_prtnum) - 1); + reg |= cpu_port; + } + WR_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_VMAP_REG, reg); + } + } + } + + /* + * enable only appropriate ports to forwarding mode + * and disable the others + */ + for (prt = 0; prt < max_prtnum; prt++) { + if ((1 << prt) & port_mask) { + RD_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, ®); + reg |= 0x3; + WR_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, reg); + } else { + /* Disable port */ + RD_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, ®); + reg &= ~0x3; + WR_PHY(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, reg); + } + } +} + +/* + * Make sure SMIBusy bit cleared before another + * SMI operation can take place + */ +static int mv88e61xx_busychk(char *name) +{ + u32 reg = 0; + u32 timeout = MV88E61XX_PHY_TIMEOUT; + do { + RD_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (u16 *) & reg); + if (timeout-- == 0) { + printf("SMI busy timeout\n"); + return -1; + } + } while (reg & 1 << 28); /* busy mask */ + return 0; +} + +/* + * Power up the specified port and reset PHY + */ +static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 prt) +{ + char *name = swconfig->name; + + /* Write Copper Specific control reg1 (0x14) for- + * Enable Phy power up + * Energy Detect on (sense&Xmit NLP Periodically + * reset other settings default + */ + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x3360); + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (0x9410 | (prt << 5))); + + if (mv88e61xx_busychk(name)) + return -1; + + /* Write PHY ctrl reg (0x0) to apply + * Phy reset (set bit 15 low) + * reset other default values + */ + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x1140); + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (0x9400 | (prt << 5))); + + if (mv88e61xx_busychk(name)) + return -1; + + return 0; +} + +/* + * Default Setup for LED[0]_Control (ref: Table 46 Datasheet-3) + * is set to "On-1000Mb/s Link, Off Else" + * This function sets it to "On-Link, Blink-Activity, Off-NoLink" + * + * This is optional settings may be needed on some boards + * to setup PHY LEDs default configuration to detect 10/100/1000Mb/s + * Link status + */ +static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 prt) +{ + char *name = swconfig->name; + u16 reg; + + if (swconfig->led_init != MV88E61XX_LED_INIT_EN) + return 0; + + /* set page address to 3 */ + reg = 3; + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg); + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST | + 1 << MV88E61XX_MODE_OFST | + 1 << MV88E61XX_OP_OFST | + prt << MV88E61XX_ADDR_OFST | 22)); + + if (mv88e61xx_busychk(name)) + return -1; + + /* set LED Func Ctrl reg */ + reg = 1; /* LED[0] On-Link, Blink-Activity, Off-NoLink */ + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg); + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST | + 1 << MV88E61XX_MODE_OFST | + 1 << MV88E61XX_OP_OFST | + prt << MV88E61XX_ADDR_OFST | 16)); + + if (mv88e61xx_busychk(name)) + return -1; + + /* set page address to 0 */ + reg = 0; + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg); + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST | + 1 << MV88E61XX_MODE_OFST | + 1 << MV88E61XX_OP_OFST | + prt << MV88E61XX_ADDR_OFST | 22)); + + if (mv88e61xx_busychk(name)) + return -1; + + return 0; +} + +/* + * Reverse Transmit polarity for Media Dependent Interface + * Pins (MDIP) bits in Copper Specific Control Register 3 + * (Page 0, Reg 20 for each phy (except cpu port) + * Reference: Section 1.1 Switch datasheet-3 + * + * This is optional settings may be needed on some boards + * for PHY<->magnetics h/w tuning + */ +static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 prt) +{ + char *name = swconfig->name; + u16 reg; + + if (swconfig->mdip != MV88E61XX_MDIP_REVERSE) + return 0; + + reg = 0x0f; /*Reverse MDIP/N[3:0] bits */ + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg); + WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST | + 1 << MV88E61XX_MODE_OFST | + 1 << MV88E61XX_OP_OFST | + prt << MV88E61XX_ADDR_OFST | 20)); + + if (mv88e61xx_busychk(name)) + return -1; + + return 0; +} + +/* + * Marvell 88E61XX Switch initialization + */ +int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig) +{ + u32 prt; + u16 reg; + char *idstr; + char *name = swconfig->name; + + if (miiphy_set_current_dev(name)) { + printf("%s failed\n", __FUNCTION__); + return -1; + } + + if (!(swconfig->cpuport & ((1 << 4) | (1 << 5)))) { + swconfig->cpuport = (1 << 5); + printf("Invalid cpu port config, using default port5\n"); + } + + RD_PHY(name, MV88E61XX_PRT_OFST, PHY_PHYIDR2, ®); + reg &= 0xfff0; + if (reg == 0x1610) + idstr = "88E6161"; + if (reg == 0x1650) + idstr = "88E6165"; + if (reg == 0x1210) { + idstr = "88E6123"; + /* ports 2,3,4 not available */ + swconfig->ports_enabled &= 0x023; + } + + /* Port based VLANs configuration */ + if ((swconfig->vlancfg == MV88E61XX_VLANCFG_DEFAULT) + || (swconfig->vlancfg == MV88E61XX_VLANCFG_ROUTER)) + mv88e61xx_port_vlan_config(swconfig, MV88E61XX_MAX_PORTS_NUM, + MV88E61XX_PRT_OFST); + else { + printf("Unsupported mode %s failed\n", __FUNCTION__); + return -1; + } + + if (swconfig->rgmii_delay == MV88E61XX_RGMII_DELAY_EN) { + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 9.5 of chip datasheet-02 + */ + WR_PHY(name, MV88E61XX_PRT_OFST + 5, + MV88E61XX_RGMII_TIMECTRL_REG, 0x18); + WR_PHY(name, MV88E61XX_PRT_OFST + 4, + MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7); + } + + for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) { + if (!((1 << prt) & swconfig->cpuport)) { + + if (mv88361xx_led_init(swconfig, prt)) + return -1; + if (mv88361xx_reverse_mdipn(swconfig, prt)) + return -1; + if (mv88361xx_powerup(swconfig, prt)) + return -1; + } + + /*Program port state */ + RD_PHY(name, MV88E61XX_PRT_OFST + prt, + MV88E61XX_PRT_CTRL_REG, ®); + WR_PHY(name, MV88E61XX_PRT_OFST + prt, + MV88E61XX_PRT_CTRL_REG, + reg | (swconfig->portstate & 0x03)); + } + + printf("%s Initialized on %s\n", idstr, name); + return 0; +} diff --git a/drivers/net/phy/mv88e61xx.h b/drivers/net/phy/mv88e61xx.h new file mode 100644 index 0000000000..42794644ec --- /dev/null +++ b/drivers/net/phy/mv88e61xx.h @@ -0,0 +1,62 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor + * Prafulla Wadaskar + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _MV88E61XX_H +#define _MV88E61XX_H + +#include + +#define MV88E61XX_CPU_PORT 0x5 +#define MV88E61XX_MAX_PORTS_NUM 0x6 + +#define MV88E61XX_PHY_TIMEOUT 100000 + +#define MV88E61XX_PRT_STS_REG 0x1 +#define MV88E61XX_PRT_CTRL_REG 0x4 +#define MV88E61XX_PRT_VMAP_REG 0x6 +#define MV88E61XX_PRT_VID_REG 0x7 + +#define MV88E61XX_PRT_OFST 0x10 +#define MV88E61XX_PHY_CMD 0x18 +#define MV88E61XX_PHY_DATA 0x19 +#define MV88E61XX_RGMII_TIMECTRL_REG 0x1A +#define MV88E61XX_GLB2REG_DEVADR 0x1C + +#define MV88E61XX_BUSY_OFST 15 +#define MV88E61XX_MODE_OFST 12 +#define MV88E61XX_OP_OFST 10 +#define MV88E61XX_ADDR_OFST 5 + +#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE +static int mv88e61xx_busychk_multic(u32 devaddr); +static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data); +static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data); +#define WR_PHY mv88e61xx_wr_phy +#define RD_PHY mv88e61xx_rd_phy +#else +#define WR_PHY miiphy_write +#define RD_PHY miiphy_read +#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */ + +#endif /* _MV88E61XX_H */ diff --git a/include/netdev.h b/include/netdev.h index 63cf730a30..4f2b23a5a0 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -116,4 +116,51 @@ static inline int pci_eth_init(bd_t *bis) return num; } +/* + * Boards with mv88e61xx switch can use this by defining + * CONFIG_MV88E61XX_SWITCH in respective board configheader file + * the stuct and enums here are used to specify switch configuration params + */ +#if defined(CONFIG_MV88E61XX_SWITCH) +enum mv88e61xx_cfg_vlan { + MV88E61XX_VLANCFG_DEFAULT, + MV88E61XX_VLANCFG_ROUTER +}; + +enum mv88e61xx_cfg_mdip { + MV88E61XX_MDIP_NOCHANGE, + MV88E61XX_MDIP_REVERSE +}; + +enum mv88e61xx_cfg_ledinit { + MV88E61XX_LED_INIT_DIS, + MV88E61XX_LED_INIT_EN +}; + +enum mv88e61xx_cfg_rgmiid { + MV88E61XX_RGMII_DELAY_DIS, + MV88E61XX_RGMII_DELAY_EN +}; + +enum mv88e61xx_cfg_prtstt { + MV88E61XX_PORTSTT_DISABLED, + MV88E61XX_PORTSTT_BLOCKING, + MV88E61XX_PORTSTT_LEARNING, + MV88E61XX_PORTSTT_FORWARDING +}; + +struct mv88e61xx_config { + char *name; + enum mv88e61xx_cfg_vlan vlancfg; + enum mv88e61xx_cfg_rgmiid rgmii_delay; + enum mv88e61xx_cfg_prtstt portstate; + enum mv88e61xx_cfg_ledinit led_init; + enum mv88e61xx_cfg_mdip mdip; + u32 ports_enabled; + u8 cpuport; +}; + +int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig); +#endif /* CONFIG_MV88E61XX_SWITCH */ + #endif /* _NETDEV_H_ */