From: Stefan Agner Date: Fri, 8 May 2015 17:07:11 +0000 (+0200) Subject: mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig X-Git-Tag: v2015.07-rc2~99^2~2 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=5519194d4f6ba3c1aeea2f07f444cc936913560a;p=oweals%2Fu-boot.git mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig This commit allows users to enable/disable the Freescale NFC controller found in systems like Vybrid (VF610), MPC5125, MCF54418 or Kinetis K70 via Kconfig with more detailed help docs. Signed-off-by: Stefan Agner Acked-by: Stefano Babic [scottwood: updated vf610twr_nand_defconfig] Signed-off-by: Scott Wood --- diff --git a/configs/colibri_vf_defconfig b/configs/colibri_vf_defconfig index 0df337c7a4..3b1f66aa76 100644 --- a/configs/colibri_vf_defconfig +++ b/configs/colibri_vf_defconfig @@ -1,3 +1,5 @@ CONFIG_ARM=y CONFIG_TARGET_COLIBRI_VF=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/colibri_vf/imximage.cfg,ENV_IS_IN_NAND,IMX_NAND" +CONFIG_NAND_VF610_NFC=y +CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES=y diff --git a/configs/vf610twr_defconfig b/configs/vf610twr_defconfig index 3a71740559..85c7c3d101 100644 --- a/configs/vf610twr_defconfig +++ b/configs/vf610twr_defconfig @@ -1,3 +1,5 @@ CONFIG_ARM=y CONFIG_TARGET_VF610TWR=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/vf610twr/imximage.cfg,ENV_IS_IN_MMC" +CONFIG_NAND_VF610_NFC=y +CONFIG_SYS_NAND_BUSWIDTH_16BIT=y diff --git a/configs/vf610twr_nand_defconfig b/configs/vf610twr_nand_defconfig index e22704ac99..ebc915c48b 100644 --- a/configs/vf610twr_nand_defconfig +++ b/configs/vf610twr_nand_defconfig @@ -1,3 +1,5 @@ CONFIG_ARM=y CONFIG_TARGET_VF610TWR=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/vf610twr/imximage.cfg,ENV_IS_IN_NAND" +CONFIG_NAND_VF610_NFC=y +CONFIG_SYS_NAND_BUSWIDTH_16BIT=y diff --git a/doc/README.nand b/doc/README.nand index 46d7edd179..0ff56331d5 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -188,24 +188,6 @@ Configuration Options: This is used by SoC platforms which do not have built-in ELM hardware engine required for BCH ECC correction. - CONFIG_SYS_NAND_BUSWIDTH_16BIT - Indicates that NAND device has 16-bit wide data-bus. In absence of this - config, bus-width of NAND device is assumed to be either 8-bit and later - determined by reading ONFI params. - Above config is useful when NAND device's bus-width information cannot - be determined from on-chip ONFI params, like in following scenarios: - - SPL boot does not support reading of ONFI parameters. This is done to - keep SPL code foot-print small. - - In current U-Boot flow using nand_init(), driver initialization - happens in board_nand_init() which is called before any device probe - (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are - not available while configuring controller. So a static CONFIG_NAND_xx - is needed to know the device's bus-width in advance. - Some drivers using above config are: - drivers/mtd/nand/mxc_nand.c - drivers/mtd/nand/ndfc.c - drivers/mtd/nand/omap_gpmc.c - Platform specific options ========================= diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 72825c3e2e..0a9e96f60a 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -32,6 +32,36 @@ config NAND_DENALI_SPARE_AREA_SKIP_BYTES of OOB area before last ECC sector data starts. This is potentially used to preserve the bad block marker in the OOB area. +config NAND_VF610_NFC + bool "Support for Freescale NFC for VF610/MPC5125" + select SYS_NAND_SELF_INIT + help + Enables support for NAND Flash Controller on some Freescale + processors like the VF610, MPC5125, MCF54418 or Kinetis K70. + The driver supports a maximum 2k page size. The driver + currently does not support hardware ECC. + +comment "Generic NAND options" + +# Enhance depends when converting drivers to Kconfig which use this config +# option (mxc_nand, ndfc, omap_gpmc). +config SYS_NAND_BUSWIDTH_16BIT + bool "Use 16-bit NAND interface" + depends on NAND_VF610_NFC + help + Indicates that NAND device has 16-bit wide data-bus. In absence of this + config, bus-width of NAND device is assumed to be either 8-bit and later + determined by reading ONFI params. + Above config is useful when NAND device's bus-width information cannot + be determined from on-chip ONFI params, like in following scenarios: + - SPL boot does not support reading of ONFI parameters. This is done to + keep SPL code foot-print small. + - In current U-Boot flow using nand_init(), driver initialization + happens in board_nand_init() which is called before any device probe + (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are + not available while configuring controller. So a static CONFIG_NAND_xx + is needed to know the device's bus-width in advance. + if SPL config SPL_NAND_DENALI diff --git a/include/configs/colibri_vf.h b/include/configs/colibri_vf.h index 414600ac43..b3c73bbb96 100644 --- a/include/configs/colibri_vf.h +++ b/include/configs/colibri_vf.h @@ -50,8 +50,6 @@ /* NAND support */ #define CONFIG_CMD_NAND -#define CONFIG_NAND_VF610_NFC -#define CONFIG_SYS_NAND_SELF_INIT #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h index 05bc7d0d9e..621aa13484 100644 --- a/include/configs/vf610twr.h +++ b/include/configs/vf610twr.h @@ -50,10 +50,7 @@ #define CONFIG_CMD_NAND_TRIMFFS #ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_VF610_NFC -#define CONFIG_SYS_NAND_SELF_INIT #define CONFIG_USE_ARCH_MEMCPY -#define CONFIG_SYS_NAND_BUSWIDTH_16BIT #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR