From: Peng Fan Date: Sun, 21 Jan 2018 11:00:24 +0000 (+0800) Subject: mmc: fsl_esdhc: support SDR104 and HS200 X-Git-Tag: v2018.03-rc2~47^2~12 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=51313b49f2;p=oweals%2Fu-boot.git mmc: fsl_esdhc: support SDR104 and HS200 Introduce SDR104 and HS200 support The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c as reference. - Implement esdhc_change_pinstate to dynamically change pad settings - Implement esdhc_set_timing - Implement esdhc_set_voltage to switch voltage - Implement fsl_esdhc_execute_tuning to execute time process - Enlarge the cfg->f_max to 200MHz. - Parse fsl,tuning-step, fsl,tuning-start-tap and fsl,strobe-dll-delay-target from device tree. - Parse no-1-8-v property - Introduce esdhc_soc_data to indicate the flags and caps Signed-off-by: Peng Fan Cc: Stefano Babic Cc: Fabio Estevam Cc: Jaehoon Chung Reviewed-by: Jaehoon Chung --- diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index 0f56bc0bee..6018f84307 100644 --- a/drivers/mmc/fsl_esdhc.c +++ b/drivers/mmc/fsl_esdhc.c @@ -23,6 +23,7 @@ #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -32,6 +33,7 @@ DECLARE_GLOBAL_DATA_PTR; IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE | \ IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \ IRQSTATEN_DINT) +#define MAX_TUNING_LOOP 40 struct fsl_esdhc { uint dsaddr; /* SDMA system address register */ @@ -90,6 +92,11 @@ struct fsl_esdhc_plat { struct mmc mmc; }; +struct esdhc_soc_data { + u32 flags; + u32 caps; +}; + /** * struct fsl_esdhc_priv * @@ -103,12 +110,20 @@ struct fsl_esdhc_plat { * @non_removable: 0: removable; 1: non-removable * @wp_enable: 1: enable checking wp; 0: no check * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V + * @flags: ESDHC_FLAG_xx in include/fsl_esdhc.h + * @caps: controller capabilities + * @tuning_step: tuning step setting in tuning_ctrl register + * @start_tuning_tap: the start point for tuning in tuning_ctrl register + * @strobe_dll_delay_target: settings in strobe_dllctrl + * @signal_voltage: indicating the current voltage * @cd_gpio: gpio for card detection * @wp_gpio: gpio for write protection */ struct fsl_esdhc_priv { struct fsl_esdhc *esdhc_regs; unsigned int sdhc_clk; + unsigned int clock; + unsigned int mode; unsigned int bus_width; #if !CONFIG_IS_ENABLED(BLK) struct mmc *mmc; @@ -117,6 +132,16 @@ struct fsl_esdhc_priv { int non_removable; int wp_enable; int vs18_enable; + u32 flags; + u32 caps; + u32 tuning_step; + u32 tuning_start_tap; + u32 strobe_dll_delay_target; + u32 signal_voltage; +#if IS_ENABLED(CONFIG_DM_REGULATOR) + struct udevice *vqmmc_dev; + struct udevice *vmmc_dev; +#endif #ifdef CONFIG_DM_GPIO struct gpio_desc cd_gpio; struct gpio_desc wp_gpio; @@ -368,6 +393,7 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc, int err = 0; uint xfertyp; uint irqstat; + u32 flags = IRQSTAT_CC | IRQSTAT_CTOE; struct fsl_esdhc *regs = priv->esdhc_regs; #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 @@ -421,8 +447,12 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc, esdhc_write32(®s->xfertyp, xfertyp); #endif + if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) || + (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) + flags = IRQSTAT_BRR; + /* Wait for the command to complete */ - while (!(esdhc_read32(®s->irqstat) & (IRQSTAT_CC | IRQSTAT_CTOE))) + while (!(esdhc_read32(®s->irqstat) & flags)) ; irqstat = esdhc_read32(®s->irqstat); @@ -484,6 +514,12 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc, #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO esdhc_pio_read_write(priv, data); #else + flags = DATA_COMPLETE; + if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) || + (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) { + flags = IRQSTAT_BRR; + } + do { irqstat = esdhc_read32(®s->irqstat); @@ -496,7 +532,7 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc, err = -ECOMM; goto out; } - } while ((irqstat & DATA_COMPLETE) != DATA_COMPLETE); + } while ((irqstat & flags) != flags); /* * Need invalidate the dcache here again to avoid any @@ -582,6 +618,7 @@ static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock) esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); #endif + priv->clock = clock; } #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK @@ -613,9 +650,239 @@ static void esdhc_clock_control(struct fsl_esdhc_priv *priv, bool enable) } #endif +#ifdef MMC_SUPPORTS_TUNING +static int esdhc_change_pinstate(struct udevice *dev) +{ + struct fsl_esdhc_priv *priv = dev_get_priv(dev); + int ret; + + switch (priv->mode) { + case UHS_SDR50: + case UHS_DDR50: + ret = pinctrl_select_state(dev, "state_100mhz"); + break; + case UHS_SDR104: + case MMC_HS_200: + ret = pinctrl_select_state(dev, "state_200mhz"); + break; + default: + ret = pinctrl_select_state(dev, "default"); + break; + } + + if (ret) + printf("%s %d error\n", __func__, priv->mode); + + return ret; +} + +static void esdhc_reset_tuning(struct mmc *mmc) +{ + struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); + struct fsl_esdhc *regs = priv->esdhc_regs; + + if (priv->flags & ESDHC_FLAG_USDHC) { + if (priv->flags & ESDHC_FLAG_STD_TUNING) { + esdhc_clrbits32(®s->autoc12err, + MIX_CTRL_SMPCLK_SEL | + MIX_CTRL_EXE_TUNE); + } + } +} + +static int esdhc_set_timing(struct mmc *mmc) +{ + struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); + struct fsl_esdhc *regs = priv->esdhc_regs; + u32 mixctrl; + + mixctrl = readl(®s->mixctrl); + mixctrl &= ~(MIX_CTRL_DDREN | MIX_CTRL_HS400_EN); + + switch (mmc->selected_mode) { + case MMC_LEGACY: + case SD_LEGACY: + esdhc_reset_tuning(mmc); + break; + case MMC_HS: + case MMC_HS_52: + case MMC_HS_200: + case SD_HS: + case UHS_SDR12: + case UHS_SDR25: + case UHS_SDR50: + case UHS_SDR104: + writel(mixctrl, ®s->mixctrl); + break; + case UHS_DDR50: + case MMC_DDR_52: + mixctrl |= MIX_CTRL_DDREN; + writel(mixctrl, ®s->mixctrl); + break; + default: + printf("Not supported %d\n", mmc->selected_mode); + return -EINVAL; + } + + priv->mode = mmc->selected_mode; + + return esdhc_change_pinstate(mmc->dev); +} + +static int esdhc_set_voltage(struct mmc *mmc) +{ + struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); + struct fsl_esdhc *regs = priv->esdhc_regs; + int ret; + + priv->signal_voltage = mmc->signal_voltage; + switch (mmc->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_330: + if (priv->vs18_enable) + return -EIO; +#ifdef CONFIG_DM_REGULATOR + if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) { + ret = regulator_set_value(priv->vqmmc_dev, 3300000); + if (ret) { + printf("Setting to 3.3V error"); + return -EIO; + } + /* Wait for 5ms */ + mdelay(5); + } +#endif + + esdhc_clrbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); + if (!(esdhc_read32(®s->vendorspec) & + ESDHC_VENDORSPEC_VSELECT)) + return 0; + + return -EAGAIN; + case MMC_SIGNAL_VOLTAGE_180: +#ifdef CONFIG_DM_REGULATOR + if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) { + ret = regulator_set_value(priv->vqmmc_dev, 1800000); + if (ret) { + printf("Setting to 1.8V error"); + return -EIO; + } + } +#endif + esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); + if (esdhc_read32(®s->vendorspec) & ESDHC_VENDORSPEC_VSELECT) + return 0; + + return -EAGAIN; + case MMC_SIGNAL_VOLTAGE_120: + return -ENOTSUPP; + default: + return 0; + } +} + +static void esdhc_stop_tuning(struct mmc *mmc) +{ + struct mmc_cmd cmd; + + cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION; + cmd.cmdarg = 0; + cmd.resp_type = MMC_RSP_R1b; + + dm_mmc_send_cmd(mmc->dev, &cmd, NULL); +} + +static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode) +{ + struct fsl_esdhc_plat *plat = dev_get_platdata(dev); + struct fsl_esdhc_priv *priv = dev_get_priv(dev); + struct fsl_esdhc *regs = priv->esdhc_regs; + struct mmc *mmc = &plat->mmc; + u32 irqstaten = readl(®s->irqstaten); + u32 irqsigen = readl(®s->irqsigen); + int i, ret = -ETIMEDOUT; + u32 val, mixctrl; + + /* clock tuning is not needed for upto 52MHz */ + if (mmc->clock <= 52000000) + return 0; + + /* This is readw/writew SDHCI_HOST_CONTROL2 when tuning */ + if (priv->flags & ESDHC_FLAG_STD_TUNING) { + val = readl(®s->autoc12err); + mixctrl = readl(®s->mixctrl); + val &= ~MIX_CTRL_SMPCLK_SEL; + mixctrl &= ~(MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN); + + val |= MIX_CTRL_EXE_TUNE; + mixctrl |= MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN; + + writel(val, ®s->autoc12err); + writel(mixctrl, ®s->mixctrl); + } + + /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE); */ + mixctrl = readl(®s->mixctrl); + mixctrl = MIX_CTRL_DTDSEL_READ | (mixctrl & ~MIX_CTRL_SDHCI_MASK); + writel(mixctrl, ®s->mixctrl); + + writel(IRQSTATEN_BRR, ®s->irqstaten); + writel(IRQSTATEN_BRR, ®s->irqsigen); + + /* + * Issue opcode repeatedly till Execute Tuning is set to 0 or the number + * of loops reaches 40 times. + */ + for (i = 0; i < MAX_TUNING_LOOP; i++) { + u32 ctrl; + + if (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200) { + if (mmc->bus_width == 8) + writel(0x7080, ®s->blkattr); + else if (mmc->bus_width == 4) + writel(0x7040, ®s->blkattr); + } else { + writel(0x7040, ®s->blkattr); + } + + /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE) */ + val = readl(®s->mixctrl); + val = MIX_CTRL_DTDSEL_READ | (val & ~MIX_CTRL_SDHCI_MASK); + writel(val, ®s->mixctrl); + + /* We are using STD tuning, no need to check return value */ + mmc_send_tuning(mmc, opcode, NULL); + + ctrl = readl(®s->autoc12err); + if ((!(ctrl & MIX_CTRL_EXE_TUNE)) && + (ctrl & MIX_CTRL_SMPCLK_SEL)) { + /* + * need to wait some time, make sure sd/mmc fininsh + * send out tuning data, otherwise, the sd/mmc can't + * response to any command when the card still out + * put the tuning data. + */ + mdelay(1); + ret = 0; + break; + } + + /* Add 1ms delay for SD and eMMC */ + mdelay(1); + } + + writel(irqstaten, ®s->irqstaten); + writel(irqsigen, ®s->irqsigen); + + esdhc_stop_tuning(mmc); + + return ret; +} +#endif + static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) { struct fsl_esdhc *regs = priv->esdhc_regs; + int ret __maybe_unused; #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK /* Select to use peripheral clock */ @@ -624,7 +891,41 @@ static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) esdhc_clock_control(priv, true); #endif /* Set the clock speed */ - set_sysctl(priv, mmc, mmc->clock); + if (priv->clock != mmc->clock) + set_sysctl(priv, mmc, mmc->clock); + +#ifdef MMC_SUPPORTS_TUNING + if (mmc->clk_disable) { +#ifdef CONFIG_FSL_USDHC + esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN); +#else + esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN); +#endif + } else { +#ifdef CONFIG_FSL_USDHC + esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | + VENDORSPEC_CKEN); +#else + esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); +#endif + } + + if (priv->mode != mmc->selected_mode) { + ret = esdhc_set_timing(mmc); + if (ret) { + printf("esdhc_set_timing error %d\n", ret); + return ret; + } + } + + if (priv->signal_voltage != mmc->signal_voltage) { + ret = esdhc_set_voltage(mmc); + if (ret) { + printf("esdhc_set_voltage error %d\n", ret); + return ret; + } + } +#endif /* Set the bus width */ esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8); @@ -799,6 +1100,10 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv, #ifndef CONFIG_FSL_USDHC esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN | SYSCTL_IPGEN | SYSCTL_CKEN); + /* Clearing tuning bits in case ROM has set it already */ + esdhc_write32(®s->mixctrl, 0); + esdhc_write32(®s->autoc12err, 0); + esdhc_write32(®s->clktunectrlstatus, 0); #else esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN); @@ -872,11 +1177,27 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv, cfg->host_caps &= ~MMC_MODE_8BIT; #endif + cfg->host_caps |= priv->caps; + cfg->f_min = 400000; - cfg->f_max = min(priv->sdhc_clk, (u32)52000000); + cfg->f_max = min(priv->sdhc_clk, (u32)200000000); cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; + writel(0, ®s->dllctrl); + if (priv->flags & ESDHC_FLAG_USDHC) { + if (priv->flags & ESDHC_FLAG_STD_TUNING) { + u32 val = readl(®s->tuning_ctrl); + + val |= ESDHC_STD_TUNING_EN; + val &= ~ESDHC_TUNING_START_TAP_MASK; + val |= priv->tuning_start_tap; + val &= ~ESDHC_TUNING_STEP_MASK; + val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT; + writel(val, ®s->tuning_ctrl); + } + } + return 0; } @@ -1035,6 +1356,10 @@ static int fsl_esdhc_probe(struct udevice *dev) struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); struct fsl_esdhc_plat *plat = dev_get_platdata(dev); struct fsl_esdhc_priv *priv = dev_get_priv(dev); + const void *fdt = gd->fdt_blob; + int node = dev_of_offset(dev); + struct esdhc_soc_data *data = + (struct esdhc_soc_data *)dev_get_driver_data(dev); #ifdef CONFIG_DM_REGULATOR struct udevice *vqmmc_dev; #endif @@ -1049,6 +1374,11 @@ static int fsl_esdhc_probe(struct udevice *dev) priv->esdhc_regs = (struct fsl_esdhc *)addr; priv->dev = dev; + priv->mode = -1; + if (data) { + priv->flags = data->flags; + priv->caps = data->caps; + } val = dev_read_u32_default(dev, "bus-width", -1); if (val == 8) @@ -1058,6 +1388,15 @@ static int fsl_esdhc_probe(struct udevice *dev) else priv->bus_width = 1; + val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1); + priv->tuning_step = val; + val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap", + ESDHC_TUNING_START_TAP_DEFAULT); + priv->tuning_start_tap = val; + val = fdtdec_get_int(fdt, node, "fsl,strobe-dll-delay-target", + ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT); + priv->strobe_dll_delay_target = val; + if (dev_read_bool(dev, "non-removable")) { priv->non_removable = 1; } else { @@ -1099,6 +1438,9 @@ static int fsl_esdhc_probe(struct udevice *dev) } #endif + if (fdt_get_property(fdt, node, "no-1-8-v", NULL)) + priv->caps &= ~(UHS_CAPS | MMC_MODE_HS200); + /* * TODO: * Because lack of clk driver, if SDHC clk is not enabled, @@ -1171,15 +1513,26 @@ static const struct dm_mmc_ops fsl_esdhc_ops = { .get_cd = fsl_esdhc_get_cd, .send_cmd = fsl_esdhc_send_cmd, .set_ios = fsl_esdhc_set_ios, +#ifdef MMC_SUPPORTS_TUNING + .execute_tuning = fsl_esdhc_execute_tuning, +#endif }; #endif +static struct esdhc_soc_data usdhc_imx7d_data = { + .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING + | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 + | ESDHC_FLAG_HS400, + .caps = UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_DDR_52MHz | + MMC_MODE_HS_52MHz | MMC_MODE_HS, +}; + static const struct udevice_id fsl_esdhc_ids[] = { { .compatible = "fsl,imx6ul-usdhc", }, { .compatible = "fsl,imx6sx-usdhc", }, { .compatible = "fsl,imx6sl-usdhc", }, { .compatible = "fsl,imx6q-usdhc", }, - { .compatible = "fsl,imx7d-usdhc", }, + { .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,}, { .compatible = "fsl,imx7ulp-usdhc", }, { .compatible = "fsl,esdhc", }, { /* sentinel */ } diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h index de1f5e7d9f..b341e018f2 100644 --- a/include/fsl_esdhc.h +++ b/include/fsl_esdhc.h @@ -10,6 +10,7 @@ #ifndef __FSL_ESDHC_H__ #define __FSL_ESDHC_H__ +#include #include #include @@ -173,6 +174,52 @@ #define ESDHC_VENDORSPEC_VSELECT 0x00000002 /* Use 1.8V */ +/* Imported from Linux Kernel drivers/mmc/host/sdhci-esdhc-imx.c */ +#define MIX_CTRL_DDREN BIT(3) +#define MIX_CTRL_DTDSEL_READ BIT(4) +#define MIX_CTRL_AC23EN BIT(7) +#define MIX_CTRL_EXE_TUNE BIT(22) +#define MIX_CTRL_SMPCLK_SEL BIT(23) +#define MIX_CTRL_AUTO_TUNE_EN BIT(24) +#define MIX_CTRL_FBCLK_SEL BIT(25) +#define MIX_CTRL_HS400_EN BIT(26) +#define MIX_CTRL_HS400_ES BIT(27) +/* Bits 3 and 6 are not SDHCI standard definitions */ +#define MIX_CTRL_SDHCI_MASK 0xb7 +/* Tuning bits */ +#define MIX_CTRL_TUNING_MASK 0x03c00000 + +/* strobe dll register */ +#define ESDHC_STROBE_DLL_CTRL 0x70 +#define ESDHC_STROBE_DLL_CTRL_ENABLE BIT(0) +#define ESDHC_STROBE_DLL_CTRL_RESET BIT(1) +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7 +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3 + +#define ESDHC_STROBE_DLL_STATUS 0x74 +#define ESDHC_STROBE_DLL_STS_REF_LOCK BIT(1) +#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1 +#define ESDHC_STROBE_DLL_CLK_FREQ 100000000 + +#define ESDHC_STD_TUNING_EN BIT(24) +/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */ +#define ESDHC_TUNING_START_TAP_DEFAULT 0x1 +#define ESDHC_TUNING_START_TAP_MASK 0xff +#define ESDHC_TUNING_STEP_MASK 0x00070000 +#define ESDHC_TUNING_STEP_SHIFT 16 + +#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1) +#define ESDHC_FLAG_ENGCM07207 BIT(2) +#define ESDHC_FLAG_USDHC BIT(3) +#define ESDHC_FLAG_MAN_TUNING BIT(4) +#define ESDHC_FLAG_STD_TUNING BIT(5) +#define ESDHC_FLAG_HAVE_CAP1 BIT(6) +#define ESDHC_FLAG_ERR004536 BIT(7) +#define ESDHC_FLAG_HS200 BIT(8) +#define ESDHC_FLAG_HS400 BIT(9) +#define ESDHC_FLAG_ERR010450 BIT(10) +#define ESDHC_FLAG_HS400_ES BIT(11) + struct fsl_esdhc_cfg { phys_addr_t esdhc_base; u32 sdhc_clk;