From: Manuel Munz Date: Sun, 8 May 2011 22:56:29 +0000 (+0000) Subject: luci-olsr: Add options for SmartGateway. X-Git-Tag: 0.11.0~2142 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=30e79c0ff3c32690aaca24b8d308bda041779767;p=oweals%2Fluci.git luci-olsr: Add options for SmartGateway. --- diff --git a/applications/luci-olsr/luasrc/model/cbi/olsr/olsrd.lua b/applications/luci-olsr/luasrc/model/cbi/olsr/olsrd.lua index f7b173cd6..82b772891 100644 --- a/applications/luci-olsr/luasrc/model/cbi/olsr/olsrd.lua +++ b/applications/luci-olsr/luasrc/model/cbi/olsr/olsrd.lua @@ -14,6 +14,9 @@ $Id$ ]]-- require("luci.tools.webadmin") +local fs = require "nixio.fs" + +local has_ipip = fs.glob("/etc/modules.d/[0-9]*-ipip")() m = Map("olsrd", translate("OLSR Daemon"), translate("The OLSR daemon is an implementation of the Optimized Link State Routing protocol. ".. @@ -47,9 +50,9 @@ s.anonymous = true s:tab("general", translate("General Settings")) s:tab("lquality", translate("Link Quality Settings")) +s:tab("smartgw", translate("SmartGW"), not has_ipip and translate("Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not work, please install it.")) s:tab("advanced", translate("Advanced Settings")) - ipv = s:taboption("general", ListValue, "IpVersion", translate("Internet protocol"), translate("IP-version to use. If 6and4 is selected then one olsrd instance is started for each protocol.")) ipv:value("4", "IPv4") @@ -144,6 +147,59 @@ mainip.rmempty = true mainip.datatype = "ipaddr" mainip.placeholder = "0.0.0.0" +sgw = s:taboption("smartgw", Flag, "SmartGateway", translate("Enable"), translate("Enable SmartGateway. If it is disabled, then " .. + "all other SmartGateway parameters are ignored. Default is \"no\".")) +sgw.default="no" +sgw.enabled="yes" +sgw.disabled="no" +sgw.rmempty = true + +sgwnat = s:taboption("smartgw", Flag, "SmartGatewayAllowNAT", translate("Allow gateways with NAT"), translate("Allow the selection of an outgoing ipv4 gateway with NAT")) +sgwnat:depends("SmartGateway", "yes") +sgwnat.default="yes" +sgwnat.enabled="yes" +sgwnat.disabled="no" +sgwnat.optional = true +sgwnat.rmempty = true + +sgwuplink = s:taboption("smartgw", ListValue, "SmartGatewayUplink", translate("Announce uplink"), translate("Which kind of uplink is exported to the other mesh nodes. " .. + "An uplink is detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. Default setting is \"both\".")) +sgwuplink:value("none") +sgwuplink:value("ipv4") +sgwuplink:value("ipv6") +sgwuplink:value("both") +sgwuplink:depends("SmartGateway", "yes") +sgwuplink.default="both" +sgwuplink.optional = true +sgwuplink.rmempty = true + +sgwulnat = s:taboption("smartgw", Flag, "SmartGatewayUplinkNAT", translate("Uplink uses NAT"), translate("If this Node uses NAT for connections to the internet. " .. + "Default is \"yes\".")) +sgwulnat:depends("SmartGatewayUplink", "ipv4") +sgwulnat:depends("SmartGatewayUplink", "both") +sgwulnat.default="yes" +sgwulnat.enabled="yes" +sgwulnat.disabled="no" +sgwnat.optional = true +sgwnat.rmempty = true + +sgwspeed = s:taboption("smartgw", Value, "SmartGatewaySpeed", translate("Speed of the uplink"), translate("Specifies the speed of ".. + "the uplink in kilobits/s. First parameter is upstream, second parameter is downstream. Default is \"128 1024\".")) +sgwspeed:depends("SmartGatewayUplink", "ipv4") +sgwspeed:depends("SmartGatewayUplink", "ipv6") +sgwspeed:depends("SmartGatewayUplink", "both") +sgwspeed.optional = true +sgwspeed.rmempty = true + +sgwprefix = s:taboption("smartgw", Value, "SmartGatewayPrefix", translate("IPv6-Prefix of the uplink"), translate("This can be used " .. + "to signal the external IPv6 prefix of the uplink to the clients. This might allow a client to change it's local IPv6 address to " .. + "use the IPv6 gateway without any kind of address translation. The maximum prefix length is 64 bits. " .. + "Default is \"::/0\" (no prefix).")) +sgwprefix:depends("SmartGatewayUplink", "ipv6") +sgwprefix:depends("SmartGatewayUplink", "both") +sgwprefix.optional = true +sgwprefix.rmempty = true + willingness = s:taboption("advanced", ListValue, "Willingness", translate("Willingness"), translate("The fixed willingness to use. If not set willingness will be calculated dynamically based on battery/power status. Default is \"3\".")) for i=0,7 do diff --git a/po/ca/olsr.po b/po/ca/olsr.po index 9a4b7a84a..d09eeb9b3 100644 --- a/po/ca/olsr.po +++ b/po/ca/olsr.po @@ -26,6 +26,15 @@ msgstr "Anuncis de xarxa de màquines actives" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Xarxa anunciada" @@ -53,6 +62,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -167,6 +181,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -175,6 +192,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -398,9 +419,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -425,6 +443,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -470,10 +496,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -490,6 +520,9 @@ msgstr "No s'ha pogut connectar al dimoni OLSR" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Utilitza histèresi" @@ -499,6 +532,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -512,5 +550,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Voluntat" diff --git a/po/de/olsr.po b/po/de/olsr.po index 27575d3f0..19920e0cb 100644 --- a/po/de/olsr.po +++ b/po/de/olsr.po @@ -3,7 +3,7 @@ msgstr "" "Project-Id-Version: PACKAGE VERSION\n" "Report-Msgid-Bugs-To: \n" "POT-Creation-Date: \n" -"PO-Revision-Date: 2011-02-12 14:23+0100\n" +"PO-Revision-Date: 2011-05-09 00:52+0100\n" "Last-Translator: Manuel Munz \n" "Language-Team: LANGUAGE \n" "Language: \n" @@ -24,6 +24,15 @@ msgstr "Aktive HNA-Ankündigungen" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "Gateways mit NAT erlauben" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "Auswahl von IPv4-Gateways erlauben, die zum Internet hin NAT verwenden" + +msgid "Announce uplink" +msgstr "Uplink ankündigen" + msgid "Announced network" msgstr "Angekündigtes Netzwerk" @@ -51,6 +60,13 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" +"SmartGateway aktivieren. Ist diese Option deaktiviert, dann werden alle " +"folgenden SmartGateway Einstellungen ignoriert. Der Defaultwert ist \"no\"." + msgid "Enable this interface." msgstr "Dieses Interface benutzen." @@ -189,6 +205,9 @@ msgstr "" "angegebenen Prefix liegt. Der Defaultwert ist \"0::/0\", damit wird eine " "IPv6-Adresse des Interfaces verwendet die nicht linklocal ist." +msgid "IPv6-Prefix of the uplink" +msgstr "IPv6-Präfix des Uplinks" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -203,6 +222,12 @@ msgstr "" ">ACHTUNG: Diese Einstellung darf nicht zusammen mit der etx_ffeth " "Metrik verwendet werden!
Der Defaultwert ist \"1.0\"." +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" +"Benutzt dieser Knoten NAT für die Verbindung zum Internet? Der Defaultwert " +"ist \"yes\"." + msgid "Interface" msgstr "" @@ -453,9 +478,6 @@ msgstr "" "dann werden die OLSR-Statusseiten nur sehr langsam laden. In diesem Fall " "sollte man diese Option deaktivieren." -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "Routen" @@ -483,6 +505,17 @@ msgstr "SmartGateway ist auf diesem System nicht konfiguriert." msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" +"Hiermit kann man die Geschwindigkeit des Uplinks dieses Knotens ankündigen. " +"Der erste Wert ist die Upload-, der zweite Wert die Downloadgeschwindigkeit. " +"Der Defaultwert ist \"128 1024\"." + +msgid "Speed of the uplink" +msgstr "Geschwindigkeit des Uplinks" + msgid "State" msgstr "" @@ -536,10 +569,18 @@ msgstr "" "Port, den OLSRd benutzt. Dieser sollte in der Regel auf dem Defaultwert 698 " "bleiben, was dem von IANA zugewiesenen Port für OLSRd entspricht." -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" +"Hiermit kann der externe IPv6-Präfix an Clients signalisiert werden. Dadurch " +"können Clients ihre lokale IP-Adresse ändern, um diesen IPv6-Gateway ohne " +"Übersetzung der IPv6-Adresse zu benutzen. Die maximale erlaubte Länge des " +"Präfix ist 64 bit. Der Defaultwert ist \"::/0\" (kein Präfix)." -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -557,6 +598,9 @@ msgstr "Es konnte keine Verbindung zum OLSR-Daemon hergestellt werden!" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "Der Uplink benutzt NAT." + msgid "Use hysteresis" msgstr "Hysterese aktivieren" @@ -566,6 +610,13 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" +"WARNUNG: kmod-ipip ist nicht installiert. Ohne kmod-ipip wird SmartGateway " +"nicht funktionieren!" + msgid "Weight" msgstr "" @@ -586,5 +637,15 @@ msgstr "" "LinkQualityLevel= 0 ist. Für alle anderen Werte von LinkQualityLevel wird " "stattdessen der ETX-Wert verwendet." +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" +"Welche Art von Uplink im Mesh angekündigt wird. Ein Uplink wird automatisch " +"anhand der lokal angekündigten HNA erkannt (0.0.0.0/0, ::ffff:0:0/96 oder " +"2000::/3). Der Defaultwert ist \"both\" (sowohl IPv4 als auch IPv6 Uplink " +"ankündigen sofern verfügbar)." + msgid "Willingness" msgstr "Bereitschaft" diff --git a/po/el/olsr.po b/po/el/olsr.po index 1f6da597c..421cef316 100644 --- a/po/el/olsr.po +++ b/po/el/olsr.po @@ -25,6 +25,15 @@ msgstr "" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "" @@ -52,6 +61,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -166,6 +180,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -174,6 +191,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -395,9 +416,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -422,6 +440,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -467,10 +493,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -487,6 +517,9 @@ msgstr "" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "" @@ -496,6 +529,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -509,5 +547,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "" diff --git a/po/en/olsr.po b/po/en/olsr.po index 9d4e9aa1d..139376479 100644 --- a/po/en/olsr.po +++ b/po/en/olsr.po @@ -25,6 +25,15 @@ msgstr "Active host net announcements" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Announced network" @@ -52,6 +61,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -166,6 +180,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -174,6 +191,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -397,9 +418,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -424,6 +442,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -469,10 +495,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -489,6 +519,9 @@ msgstr "Unable to connect to the OLSR daemon!" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Use hysteresis" @@ -498,6 +531,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -511,5 +549,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Willingness" diff --git a/po/es/olsr.po b/po/es/olsr.po index d896edc5f..baf787f2e 100644 --- a/po/es/olsr.po +++ b/po/es/olsr.po @@ -24,6 +24,15 @@ msgstr "Anuncios activos del host de red" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Red a anunciar" @@ -51,6 +60,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -165,6 +179,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -173,6 +190,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -397,9 +418,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -424,6 +442,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -469,10 +495,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -489,6 +519,9 @@ msgstr "No es posible conectar con el demonio de OLSR! " msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Uso de histéresis" @@ -498,6 +531,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -511,5 +549,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Voluntad" diff --git a/po/fr/olsr.po b/po/fr/olsr.po index 88d614452..88d808e7e 100644 --- a/po/fr/olsr.po +++ b/po/fr/olsr.po @@ -25,6 +25,15 @@ msgstr "" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "" @@ -52,6 +61,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -166,6 +180,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -174,6 +191,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -395,9 +416,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -422,6 +440,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -467,10 +493,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -487,6 +517,9 @@ msgstr "" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "" @@ -496,6 +529,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -509,5 +547,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "" diff --git a/po/it/olsr.po b/po/it/olsr.po index 88d614452..88d808e7e 100644 --- a/po/it/olsr.po +++ b/po/it/olsr.po @@ -25,6 +25,15 @@ msgstr "" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "" @@ -52,6 +61,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -166,6 +180,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -174,6 +191,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -395,9 +416,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -422,6 +440,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -467,10 +493,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -487,6 +517,9 @@ msgstr "" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "" @@ -496,6 +529,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -509,5 +547,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "" diff --git a/po/ja/olsr.po b/po/ja/olsr.po index 88d614452..88d808e7e 100644 --- a/po/ja/olsr.po +++ b/po/ja/olsr.po @@ -25,6 +25,15 @@ msgstr "" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "" @@ -52,6 +61,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -166,6 +180,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -174,6 +191,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -395,9 +416,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -422,6 +440,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -467,10 +493,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -487,6 +517,9 @@ msgstr "" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "" @@ -496,6 +529,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -509,5 +547,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "" diff --git a/po/pt/olsr.po b/po/pt/olsr.po index 9d9d5d661..da78b8965 100644 --- a/po/pt/olsr.po +++ b/po/pt/olsr.po @@ -26,6 +26,15 @@ msgstr "Anuncios activos de hosts" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Rede anunciada" @@ -53,6 +62,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -167,6 +181,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -175,6 +192,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -401,9 +422,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -428,6 +446,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -473,10 +499,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -493,6 +523,9 @@ msgstr "Não foi possivel ligar ao servidor OLSR!" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Usar histerese" @@ -502,6 +535,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -515,5 +553,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Disponibilidade" diff --git a/po/pt_BR/olsr.po b/po/pt_BR/olsr.po index 7fb2396da..a96575675 100644 --- a/po/pt_BR/olsr.po +++ b/po/pt_BR/olsr.po @@ -26,6 +26,15 @@ msgstr "Anuncios activos de hosts" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Rede anunciada" @@ -53,6 +62,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -167,6 +181,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -175,6 +192,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -401,9 +422,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -428,6 +446,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -473,10 +499,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -493,6 +523,9 @@ msgstr "Não foi possivel ligar ao servidor OLSR!" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Usar histerese" @@ -502,6 +535,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -515,5 +553,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Disponibilidade" diff --git a/po/ru/olsr.po b/po/ru/olsr.po index 88d614452..88d808e7e 100644 --- a/po/ru/olsr.po +++ b/po/ru/olsr.po @@ -25,6 +25,15 @@ msgstr "" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "" @@ -52,6 +61,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -166,6 +180,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -174,6 +191,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -395,9 +416,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -422,6 +440,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -467,10 +493,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -487,6 +517,9 @@ msgstr "" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "" @@ -496,6 +529,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -509,5 +547,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "" diff --git a/po/templates/olsr.pot b/po/templates/olsr.pot index f8b7ffe94..941972e8d 100644 --- a/po/templates/olsr.pot +++ b/po/templates/olsr.pot @@ -13,6 +13,15 @@ msgstr "" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "" @@ -40,6 +49,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -154,6 +168,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -162,6 +179,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -383,9 +404,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -410,6 +428,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -455,10 +481,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -475,6 +505,9 @@ msgstr "" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "" @@ -484,6 +517,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -497,5 +535,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "" diff --git a/po/vi/olsr.po b/po/vi/olsr.po index cec7dba01..fe435c136 100644 --- a/po/vi/olsr.po +++ b/po/vi/olsr.po @@ -26,6 +26,15 @@ msgstr "Thông báo của mạng host đang hoạt động" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Mạng lưới thông báo" @@ -53,6 +62,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -167,6 +181,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -175,6 +192,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -399,9 +420,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -426,6 +444,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -471,10 +497,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -491,6 +521,9 @@ msgstr "Không thể kết nối với OLSR daemon!" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Dùng hysteresis" @@ -500,6 +533,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -513,5 +551,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Sẵn sàng"