From: Davide Fioravanti Date: Sun, 19 Jan 2020 20:05:31 +0000 (+0100) Subject: ath79: add support for TP-Link Archer D7/D7b v1 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=213250b56bb4a3043dcb5a48e2f849b9e45967d7;p=oweals%2Fopenwrt.git ath79: add support for TP-Link Archer D7/D7b v1 TP-Link Archer D7 v1 is a dual-band AC1750 router + modem. The router section is based on Qualcomm/Atheros QCA9558 + QCA9880. The "DSL" section is based on BCM6318 but it's currently not supported. The Archer D7b seems to differ from the Archer D7 only in the partition table. Router section - Specification: 775/650/258 MHz (CPU/DDR/AHB) 128 MB of RAM (DDR2) 16 MB of FLASH (SPI NOR) 3T3R 2.4 GHz 3T3R 5 GHz 4x 10/100/1000 Mbps Ethernet 7x LED, 2x button UART header on PCB Known issues: - Broadband LED (missing GPIO - probably driven by the BCM6318) - Internet LED (missing GPIO - probably driven by the BCM6318) - WIFI LED (working only for one interface at a time, while in the OEM firmware works for both wifi interfaces; thus, this patch does not set a trigger by default) - DSL not working (eth0) UART connection --------------- J1 HEADER (Qualcomm CPU) . VCC . GND . RX O TX J41 HEADER (Broadcom CPU) . VCC . GND . RX O TX The following instructions require a connection to the J1 UART header and are tested for the Archer D7 v1. For the Archer D7b v1, names should be changed accordingly. Flash instructions under U-Boot, using UART ------------------------------------------ 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin erase 0x9f020000 +f90000 cp.b 0x81000000 0x9f020000 0xf90000 reset Initramfs instructions under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin bootm 0x81000000 4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872 4. Double check the .mod file size. It must be 16318464 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod erase 0x9f020000 +f90000 cp.b 0x81000000 0x9f020000 0xf90000 reset Signed-off-by: Davide Fioravanti [cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two phyXtpt at once, add missing buttons, minor commit message adjustments] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-d7-v1.dts b/target/linux/ath79/dts/qca9558_tplink_archer-d7-v1.dts new file mode 100644 index 0000000000..8fae6545e3 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_tplink_archer-d7-v1.dts @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9558_tplink_archer-d7.dtsi" + +/ { + compatible = "tplink,archer-d7-v1", "qca,qca9558"; + model = "TP-Link Archer D7 v1"; + + aliases { + label-mac-device = &wmac; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x020000 0xf90000>; + }; + + partition@fb0000 { + label = "radioDECT"; + reg = <0xfb0000 0x010000>; + read-only; + }; + + partition@fc0000 { + label = "config"; + reg = <0xfc0000 0x010000>; + read-only; + }; + + romfs: partition@fd0000 { + label = "romfs"; + reg = <0xfd0000 0x010000>; + read-only; + }; + + partition@fe0000 { + label = "rom"; + reg = <0xfe0000 0x010000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +ð0 { + mtd-mac-address = <&romfs 0xf100>; + mtd-mac-address-increment = <1>; +}; + +ð1 { + mtd-mac-address = <&romfs 0xf100>; +}; + +&wmac { + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&romfs 0xf100>; +}; diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-d7.dtsi b/target/linux/ath79/dts/qca9558_tplink_archer-d7.dtsi new file mode 100644 index 0000000000..a65d4e2b53 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_tplink_archer-d7.dtsi @@ -0,0 +1,179 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include + +#include "qca9557.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "tp-link:white:system"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan { + label = "tp-link:white:wlan"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "tp-link:white:lan"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + + usb { + label = "tp-link:white:usb"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + trigger-sources = <&hub_port1>, <&hub_port0>; + linux,default-trigger = "usbport"; + }; + + qss { + label = "tp-link:white:qss"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + wifi { + label = "WiFi button"; + linux,code = ; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + }; + + reg_usb0_vbus: regulator { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 21 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb1_vbus: regulator { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */ + 0x50 0xc737c737 /* LED_CTRL0 */ + 0x54 0x00000000 /* LED_CTRL1 */ + 0x58 0x00000000 /* LED_CTRL2 */ + 0x5c 0x0030c300 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6 STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&phy0>; + pll-data = <0x56000000 0x00000101 0x00001616>; + + gmac-config { + device = <&gmac>; + rgmii-enabled = <1>; + }; +}; + +ð1 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&wmac { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + #address-cells = <1>; + #size-cells = <0>; + dr_mode = "host"; + vbus-supply = <®_usb0_vbus>; + status = "okay"; + + hub_port0: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb1 { + #address-cells = <1>; + #size-cells = <0>; + dr_mode = "host"; + vbus-supply = <®_usb1_vbus>; + status = "okay"; + + hub_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts b/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts new file mode 100644 index 0000000000..31563d9c46 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9558_tplink_archer-d7.dtsi" + +/ { + compatible = "tplink,archer-d7b-v1", "qca,qca9558"; + model = "TP-Link Archer D7b v1"; + + aliases { + label-mac-device = &wmac; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x020000 0xfa0000>; + }; + + partition@fc0000 { + label = "config"; + reg = <0xfc0000 0x010000>; + read-only; + }; + + romfs: partition@fd0000 { + label = "romfs"; + reg = <0xfd0000 0x010000>; + read-only; + }; + + partition@fe0000 { + label = "reserve"; + reg = <0xfe0000 0x010000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +ð0 { + mtd-mac-address = <&romfs 0xf100>; + mtd-mac-address-increment = <1>; +}; + +ð1 { + mtd-mac-address = <&romfs 0xf100>; +}; + +&wmac { + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&romfs 0xf100>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 3864423e58..227ccf0dfe 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -187,6 +187,10 @@ tplink,archer-d50-v1) ucidef_set_led_switch "wan_data" "WAN Data" "tp-link:white:internet" "switch0" "0x02" "" "tx rx" ucidef_set_led_switch "wan_link" "WAN Link" "tp-link:white:wan" "switch0" "0x02" "" "link" ;; +tplink,archer-d7-v1|\ +tplink,archer-d7b-v1) + ucidef_set_led_switch "lan" "LAN" "tp-link:white:lan" "switch0" "0x3c" + ;; tplink,cpe210-v1|\ tplink,cpe220-v2|\ tplink,cpe220-v3|\ diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 33a4b0e884..dbb722482b 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -252,6 +252,11 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan" ;; + tplink,archer-d7-v1|\ + tplink,archer-d7b-v1) + ucidef_add_switch "switch0" \ + "0@eth1" "3:lan:3" "4:lan:2" "5:lan:1" "6@eth0" "2:wan:4" "1:wan:5" + ;; tplink,tl-mr6400-v1) ucidef_set_interfaces_lan_wan "eth0.1 eth1" "usb0" ucidef_add_switch "switch0" \ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 43c2f9ced5..d354c7eaec 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -99,6 +99,11 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2) ;; + tplink,archer-d7-v1|\ + tplink,archer-d7b-v1) + caldata_extract "art" 0x5000 0x844 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfs 0xf100) +2) + ;; tplink,re350k-v1) caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2) diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index ffa445697c..18f5233c09 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -217,6 +217,35 @@ define Device/tplink_archer-d50-v1 endef TARGET_DEVICES += tplink_archer-d50-v1 +define Device/tplink_archer-d7-v1 + $(Device/tplink-v2) + SOC := qca9558 + DEVICE_MODEL := Archer D7 + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport \ + kmod-ath10k-ct ath10k-firmware-qca988x-ct + IMAGE_SIZE := 15936k + TPLINK_HWID := 0x89300001 + TPLINK_HWREV := 0x0000002D + TPLINK_FLASHLAYOUT := 16Mqca + TPLINK_HWREVADD := 0x00000002 +endef +TARGET_DEVICES += tplink_archer-d7-v1 + +define Device/tplink_archer-d7b-v1 + $(Device/tplink-v2) + SOC := qca9558 + DEVICE_MODEL := Archer D7b + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport \ + kmod-ath10k-ct ath10k-firmware-qca988x-ct + IMAGE_SIZE := 16000k + TPLINK_HWID := 0x89300001 + TPLINK_HWREV := 0x0000003D + TPLINK_FLASHLAYOUT := 16Mqca +endef +TARGET_DEVICES += tplink_archer-d7b-v1 + define Device/tplink_cpe210-v1 $(Device/tplink-safeloader-okli) SOC := ar9344