From: Jean-Jacques Hiblot Date: Fri, 7 Dec 2018 13:50:49 +0000 (+0100) Subject: ti: remove usage of DM_I2C_COMPAT and don't disable DM_I2C in SPL X-Git-Tag: v2019.01-rc2~14^2~7 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=1514244cc137fe29c9321ea2990de2ec827a9549;p=oweals%2Fu-boot.git ti: remove usage of DM_I2C_COMPAT and don't disable DM_I2C in SPL DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT when all I2C "clients" have been migrated to use the DM API. This a step in that direction for the TI based platforms. Build tested with buildman: buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone boot tested with: am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version), am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Tom Rini Reviewed-by: Heiko Schocher --- diff --git a/arch/arm/mach-keystone/ddr3_spd.c b/arch/arm/mach-keystone/ddr3_spd.c index 2613092552..6eee9ad13a 100644 --- a/arch/arm/mach-keystone/ddr3_spd.c +++ b/arch/arm/mach-keystone/ddr3_spd.c @@ -403,6 +403,7 @@ static void init_ddr3param(struct ddr3_spd_cb *spd_cb, static int ddr3_read_spd(ddr3_spd_eeprom_t *spd_params) { int ret; +#ifndef CONFIG_DM_I2C int old_bus; i2c_init(CONFIG_SYS_DAVINCI_I2C_SPEED, CONFIG_SYS_DAVINCI_I2C_SLAVE); @@ -413,7 +414,13 @@ static int ddr3_read_spd(ddr3_spd_eeprom_t *spd_params) ret = i2c_read(0x53, 0, 1, (unsigned char *)spd_params, 256); i2c_set_bus_num(old_bus); +#else + struct udevice *dev; + ret = i2c_get_chip_for_busnum(1, 0x53, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, 0, (unsigned char *)spd_params, 256); +#endif if (ret) { printf("Cannot read DIMM params\n"); return 1; diff --git a/arch/arm/mach-omap2/am33xx/clk_synthesizer.c b/arch/arm/mach-omap2/am33xx/clk_synthesizer.c index 0e7ad1d3af..ff1bfaf84b 100644 --- a/arch/arm/mach-omap2/am33xx/clk_synthesizer.c +++ b/arch/arm/mach-omap2/am33xx/clk_synthesizer.c @@ -14,6 +14,7 @@ /** * clk_synthesizer_reg_read - Read register from synthesizer. + * dev: i2c bus device (not used if CONFIG_DM_I2C is not set) * @addr: addr within the i2c device * buf: Buffer to which value is to be read. * @@ -21,13 +22,14 @@ * be send along with enabling byte read more, and then read can happen. * Returns 0 on success */ -static int clk_synthesizer_reg_read(int addr, uint8_t *buf) +static int clk_synthesizer_reg_read(struct udevice *dev, int addr, u8 *buf) { int rc; /* Enable Bye read */ addr = addr | CLK_SYNTHESIZER_BYTE_MODE; +#ifndef CONFIG_DM_I2C /* Send the command byte */ rc = i2c_write(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1); if (rc) @@ -35,26 +37,46 @@ static int clk_synthesizer_reg_read(int addr, uint8_t *buf) /* Read the Data */ return i2c_read(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1); +#else + /* Send the command byte */ + rc = dm_i2c_reg_write(dev, addr, *buf); + if (rc) + printf("Failed to send command to clock synthesizer\n"); + + /* Read the Data */ + rc = dm_i2c_reg_read(dev, addr); + if (rc < 0) + return rc; + + *buf = (u8)rc; + return 0; +#endif + } /** * clk_synthesizer_reg_write - Write a value to register in synthesizer. + * dev: i2c bus device (not used if CONFIG_DM_I2C is not set) * @addr: addr within the i2c device * val: Value to be written in the addr. * * Enable the byte read mode in the address and start the i2c transfer. * Returns 0 on success */ -static int clk_synthesizer_reg_write(int addr, uint8_t val) +static int clk_synthesizer_reg_write(struct udevice *dev, int addr, u8 val) { - uint8_t cmd[2]; + u8 cmd[2]; int rc = 0; /* Enable byte write */ cmd[0] = addr | CLK_SYNTHESIZER_BYTE_MODE; cmd[1] = val; +#ifndef CONFIG_DM_I2C rc = i2c_write(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, cmd, 2); +#else + rc = dm_i2c_write(dev, addr, cmd, 2); +#endif if (rc) printf("Clock synthesizer reg write failed at addr = 0x%x\n", addr); @@ -72,30 +94,42 @@ static int clk_synthesizer_reg_write(int addr, uint8_t val) int setup_clock_synthesizer(struct clk_synth *data) { int rc; - uint8_t val; - + u8 val = 0; + struct udevice *dev = NULL; +#ifndef CONFIG_DM_I2C rc = i2c_probe(CLK_SYNTHESIZER_I2C_ADDR); if (rc) { printf("i2c probe failed at address 0x%x\n", CLK_SYNTHESIZER_I2C_ADDR); return rc; } - - rc = clk_synthesizer_reg_read(CLK_SYNTHESIZER_ID_REG, &val); +#else + rc = i2c_get_chip_for_busnum(0, CLK_SYNTHESIZER_I2C_ADDR, 1, &dev); + if (rc) { + printf("failed to get device for synthesizer at address 0x%x\n", + CLK_SYNTHESIZER_I2C_ADDR); + return rc; + } +#endif + rc = clk_synthesizer_reg_read(dev, CLK_SYNTHESIZER_ID_REG, &val); if (val != data->id) return rc; /* Crystal Load capacitor selection */ - rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_XCSEL, data->capacitor); + rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_XCSEL, + data->capacitor); if (rc) return rc; - rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_MUX_REG, data->mux); + rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_MUX_REG, + data->mux); if (rc) return rc; - rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_PDIV2_REG, data->pdiv2); + rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_PDIV2_REG, + data->pdiv2); if (rc) return rc; - rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_PDIV3_REG, data->pdiv3); + rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_PDIV3_REG, + data->pdiv3); if (rc) return rc; diff --git a/arch/arm/mach-omap2/clocks-common.c b/arch/arm/mach-omap2/clocks-common.c index 790548ee79..5932d694d3 100644 --- a/arch/arm/mach-omap2/clocks-common.c +++ b/arch/arm/mach-omap2/clocks-common.c @@ -909,6 +909,7 @@ void prcm_init(void) enable_basic_uboot_clocks(); } +#if !defined(CONFIG_DM_I2C) void gpi2c_init(void) { static int gpi2c = 1; @@ -919,3 +920,4 @@ void gpi2c_init(void) gpi2c = 0; } } +#endif diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 13845251af..d67f94ad47 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -70,8 +70,9 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; void do_board_detect(void) { enable_i2c0_pin_mux(); +#ifndef CONFIG_DM_I2C i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); - +#endif if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, CONFIG_EEPROM_CHIP_ADDRESS)) printf("ti_i2c_eeprom_init failed\n"); @@ -328,8 +329,14 @@ static void scale_vcores_bone(int freq) if (board_is_bone() && !strncmp(board_ti_get_rev(), "00A1", 4)) return; +#ifndef CONFIG_DM_I2C if (i2c_probe(TPS65217_CHIP_PM)) return; +#else + if (power_tps65217_init(0)) + return; +#endif + /* * On Beaglebone White we need to ensure we have AC power @@ -421,9 +428,13 @@ void scale_vcores_generic(int freq) * 1.10V. For MPU voltage we need to switch based on * the frequency we are running at. */ +#ifndef CONFIG_DM_I2C if (i2c_probe(TPS65910_CTRL_I2C_ADDR)) return; - +#else + if (power_tps65910_init(0)) + return; +#endif /* * Depending on MPU clock and PG we will need a different * VDD to drive at that speed. @@ -451,8 +462,10 @@ void gpi2c_init(void) if (first_time) { enable_i2c0_pin_mux(); +#ifndef CONFIG_DM_I2C i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); +#endif first_time = false; } } diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c index 41333f93f4..04f4b8e693 100644 --- a/board/ti/am335x/mux.c +++ b/board/ti/am335x/mux.c @@ -329,12 +329,23 @@ static unsigned short detect_daughter_board_profile(void) { unsigned short val; +#ifndef CONFIG_DM_I2C if (i2c_probe(I2C_CPLD_ADDR)) return PROFILE_NONE; if (i2c_read(I2C_CPLD_ADDR, CFG_REG, 1, (unsigned char *)(&val), 2)) return PROFILE_NONE; +#else + struct udevice *dev = NULL; + int rc; + rc = i2c_get_chip_for_busnum(0, I2C_CPLD_ADDR, 1, &dev); + if (rc) + return PROFILE_NONE; + rc = dm_i2c_read(dev, CFG_REG, (unsigned char *)(&val), 2); + if (rc) + return PROFILE_NONE; +#endif return (1 << (val & PROFILE_MASK)); } diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index 2a59b06035..31bc0f49a4 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -43,6 +43,8 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; #ifdef CONFIG_TI_I2C_BOARD_DETECT void do_board_detect(void) { + /* Ensure I2C is initialized for EEPROM access*/ + gpi2c_init(); if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, CONFIG_EEPROM_CHIP_ADDRESS)) printf("ti_i2c_eeprom_init failed\n"); @@ -386,8 +388,13 @@ void scale_vcores_generic(u32 m) { int mpu_vdd, ddr_volt; +#ifndef CONFIG_DM_I2C if (i2c_probe(TPS65218_CHIP_PM)) return; +#else + if (power_tps65218_init(0)) + return; +#endif switch (m) { case 1000: @@ -439,8 +446,13 @@ void scale_vcores_idk(u32 m) { int mpu_vdd; +#ifndef CONFIG_DM_I2C if (i2c_probe(TPS62362_I2C_ADDR)) return; +#else + if (power_tps62362_init(0)) + return; +#endif switch (m) { case 1000: @@ -462,14 +474,12 @@ void scale_vcores_idk(u32 m) puts("Unknown MPU clock, not scaling\n"); return; } - /* Set VDD_MPU voltage */ if (tps62362_voltage_update(TPS62362_SET3, mpu_vdd)) { printf("%s failure\n", __func__); return; } } - void gpi2c_init(void) { /* When needed to be invoked prior to BSS initialization */ @@ -477,8 +487,10 @@ void gpi2c_init(void) if (first_time) { enable_i2c0_pin_mux(); +#ifndef CONFIG_DM_I2C i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); +#endif first_time = false; } } @@ -614,20 +626,32 @@ void sdram_init(void) /* setup board specific PMIC */ int power_init_board(void) { - struct pmic *p; - + int rc; +#ifndef CONFIG_DM_I2C + struct pmic *p = NULL; +#endif if (board_is_idk()) { - power_tps62362_init(I2C_PMIC); + rc = power_tps62362_init(0); + if (rc) + goto done; +#ifndef CONFIG_DM_I2C p = pmic_get("TPS62362"); - if (p && !pmic_probe(p)) - puts("PMIC: TPS62362\n"); + if (!p || pmic_probe(p)) + goto done; +#endif + puts("PMIC: TPS62362\n"); } else { - power_tps65218_init(I2C_PMIC); + rc = power_tps65218_init(0); + if (rc) + goto done; +#ifndef CONFIG_DM_I2C p = pmic_get("TPS65218_PMIC"); - if (p && !pmic_probe(p)) - puts("PMIC: TPS65218\n"); + if (!p || pmic_probe(p)) + goto done; +#endif + puts("PMIC: TPS65218\n"); } - +done: return 0; } diff --git a/board/ti/am57xx/board.c b/board/ti/am57xx/board.c index 177a3246c3..355ea55609 100644 --- a/board/ti/am57xx/board.c +++ b/board/ti/am57xx/board.c @@ -623,7 +623,7 @@ void am57x_idk_lcd_detect(void) { int r = -ENODEV; char *idk_lcd = "no"; - uint8_t buf = 0; + u8 buf = 0; /* Only valid for IDKs */ if (board_is_x15() || board_is_am572x_evm()) @@ -633,6 +633,7 @@ void am57x_idk_lcd_detect(void) if (board_is_am571x_idk() && !am571x_idk_needs_lcd()) goto out; +#ifndef CONFIG_DM_I2C r = i2c_set_bus_num(OSD_TS_FT_BUS_ADDRESS); if (r) { printf("%s: Failed to set bus address to %d: %d\n", @@ -657,6 +658,32 @@ void am57x_idk_lcd_detect(void) OSD_TS_FT_REG_ID, r); goto out; } +#else + struct udevice *dev; + + r = i2c_get_chip_for_busnum(OSD_TS_FT_BUS_ADDRESS, + OSD_TS_FT_CHIP_ADDRESS, 1, &dev); + if (r) { + printf("%s: Failed to get I2C device %d/%d (ret %d)\n", + __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS, + r); + /* AM572x IDK has no explicit settings for optional LCD kit */ + if (board_is_am571x_idk()) + printf("%s: Touch screen detect failed: %d!\n", + __func__, r); + goto out; + } + + /* Read FT ID */ + r = dm_i2c_reg_read(dev, OSD_TS_FT_REG_ID); + if (r < 0) { + printf("%s: Touch screen ID read %d:0x%02x[0x%02x] failed:%d\n", + __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS, + OSD_TS_FT_REG_ID, r); + goto out; + } + buf = (u8)r; +#endif switch (buf) { case OSD_TS_FT_ID_5606: diff --git a/board/ti/common/board_detect.c b/board/ti/common/board_detect.c index 085e7320bd..e258e22f37 100644 --- a/board/ti/common/board_detect.c +++ b/board/ti/common/board_detect.c @@ -14,43 +14,7 @@ #include "board_detect.h" -#if defined(CONFIG_DM_I2C_COMPAT) -/** - * ti_i2c_set_alen - Set chip's i2c address length - * @bus_addr - I2C bus number - * @dev_addr - I2C eeprom id - * @alen - I2C address length in bytes - * - * DM_I2C by default sets the address length to be used to 1. This - * function allows this address length to be changed to match the - * eeprom used for board detection. - */ -int __maybe_unused ti_i2c_set_alen(int bus_addr, int dev_addr, int alen) -{ - struct udevice *dev; - struct udevice *bus; - int rc; - - rc = uclass_get_device_by_seq(UCLASS_I2C, bus_addr, &bus); - if (rc) - return rc; - rc = i2c_get_chip(bus, dev_addr, 1, &dev); - if (rc) - return rc; - rc = i2c_set_chip_offset_len(dev, alen); - if (rc) - return rc; - - return 0; -} -#else -int __maybe_unused ti_i2c_set_alen(int bus_addr, int dev_addr, int alen) -{ - return 0; -} -#endif - -#if !defined(CONFIG_DM_I2C) || defined(CONFIG_DM_I2C_COMPAT) +#if !defined(CONFIG_DM_I2C) /** * ti_i2c_eeprom_init - Initialize an i2c bus and probe for a device * @i2c_bus: i2c bus number to initialize @@ -83,17 +47,7 @@ static int __maybe_unused ti_i2c_eeprom_init(int i2c_bus, int dev_addr) static int __maybe_unused ti_i2c_eeprom_read(int dev_addr, int offset, uchar *ep, int epsize) { - int bus_num, rc, alen; - - bus_num = i2c_get_bus_num(); - - alen = 2; - - rc = ti_i2c_set_alen(bus_num, dev_addr, alen); - if (rc) - return rc; - - return i2c_read(dev_addr, offset, alen, ep, epsize); + return i2c_read(dev_addr, offset, 2, ep, epsize); } #endif @@ -127,7 +81,7 @@ static int __maybe_unused ti_i2c_eeprom_get(int bus_addr, int dev_addr, u32 hdr_read; int rc; -#if defined(CONFIG_DM_I2C) && !defined(CONFIG_DM_I2C_COMPAT) +#if defined(CONFIG_DM_I2C) struct udevice *dev; struct udevice *bus; @@ -185,10 +139,6 @@ static int __maybe_unused ti_i2c_eeprom_get(int bus_addr, int dev_addr, */ byte = 2; - rc = ti_i2c_set_alen(bus_addr, dev_addr, byte); - if (rc) - return rc; - rc = i2c_read(dev_addr, 0x0, byte, (uint8_t *)&hdr_read, 4); if (rc) return rc; @@ -202,10 +152,6 @@ static int __maybe_unused ti_i2c_eeprom_get(int bus_addr, int dev_addr, */ byte = 1; if (rc) { - rc = ti_i2c_set_alen(bus_addr, dev_addr, byte); - if (rc) - return rc; - rc = i2c_read(dev_addr, 0x0, byte, (uint8_t *)&hdr_read, 4); } diff --git a/board/ti/ks2_evm/board_k2g.c b/board/ti/ks2_evm/board_k2g.c index 87dc4d009e..39a782e479 100644 --- a/board/ti/ks2_evm/board_k2g.c +++ b/board/ti/ks2_evm/board_k2g.c @@ -251,6 +251,7 @@ int board_fit_config_name_match(const char *name) #if defined(CONFIG_DTB_RESELECT) static int k2g_alt_board_detect(void) { +#ifndef CONFIG_DM_I2C int rc; rc = i2c_set_bus_num(1); @@ -260,7 +261,17 @@ static int k2g_alt_board_detect(void) rc = i2c_probe(K2G_GP_AUDIO_CODEC_ADDRESS); if (rc) return rc; +#else + struct udevice *bus, *dev; + int rc; + rc = uclass_get_device_by_seq(UCLASS_I2C, 1, &bus); + if (rc) + return rc; + rc = dm_i2c_probe(bus, K2G_GP_AUDIO_CODEC_ADDRESS, 0, &dev); + if (rc) + return rc; +#endif ti_i2c_eeprom_am_set("66AK2GGP", "1.0X"); return 0; diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index 9d0d342478..ed71f4ce56 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -27,8 +27,10 @@ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Power */ +#ifndef CONFIG_DM_I2C #define CONFIG_POWER #define CONFIG_POWER_I2C +#endif #define CONFIG_POWER_TPS65218 #define CONFIG_POWER_TPS62362 diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h index 0f892e51d1..1e2a62dd6f 100644 --- a/include/configs/ti_armv7_common.h +++ b/include/configs/ti_armv7_common.h @@ -74,24 +74,10 @@ /* Timer information. */ #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ -/* - * Disable DM_* for SPL build and can be re-enabled after adding - * DM support in SPL - */ -#ifdef CONFIG_SPL_BUILD -#undef CONFIG_DM_I2C -#endif - -/* I2C IP block */ +/* If DM_I2C, enable non-DM I2C support */ +#if !defined(CONFIG_DM_I2C) #define CONFIG_I2C -#ifndef CONFIG_DM_I2C #define CONFIG_SYS_I2C -#else -/* - * Enable CONFIG_DM_I2C_COMPAT temporarily until all the i2c client - * devices are adopted to DM - */ -#define CONFIG_DM_I2C_COMPAT #endif /*