From: Chuanhua Han Date: Wed, 10 Jul 2019 13:00:20 +0000 (+0800) Subject: boards: lx2160a: Add support of I2C driver model X-Git-Tag: v2019.10-rc3~7^2~39 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=0eba65d2013e5517e70cc9b3d467ba8183b54cd9;p=oweals%2Fu-boot.git boards: lx2160a: Add support of I2C driver model DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the lx2160a platform does not support dm. Signed-off-by: Chuanhua Han Reviewed-by: Prabhakar Kushwaha --- diff --git a/board/freescale/common/emc2305.c b/board/freescale/common/emc2305.c index 8523084da9..b1ca051db2 100644 --- a/board/freescale/common/emc2305.c +++ b/board/freescale/common/emc2305.c @@ -24,10 +24,22 @@ void set_fan_speed(u8 data) I2C_EMC2305_FAN5}; for (index = 0; index < NUM_OF_FANS; index++) { +#ifndef CONFIG_DM_I2C if (i2c_write(I2C_EMC2305_ADDR, Fan[index], 1, &data, 1) != 0) { printf("Error: failed to change fan speed @%x\n", Fan[index]); } +#else + struct udevice *dev; + + if (i2c_get_chip_for_busnum(0, I2C_EMC2305_ADDR, 1, &dev)) + continue; + + if (dm_i2c_write(dev, Fan[index], &data, 1) != 0) { + printf("Error: failed to change fan speed @%x\n", + Fan[index]); + } +#endif } } @@ -36,6 +48,15 @@ void emc2305_init(void) u8 data; data = I2C_EMC2305_CMD; +#ifndef CONFIG_DM_I2C if (i2c_write(I2C_EMC2305_ADDR, I2C_EMC2305_CONF, 1, &data, 1) != 0) printf("Error: failed to configure EMC2305\n"); +#else + struct udevice *dev; + + if (!i2c_get_chip_for_busnum(0, I2C_EMC2305_ADDR, 1, &dev)) + if (dm_i2c_write(dev, I2C_EMC2305_CONF, &data, 1)) + printf("Error: failed to configure EMC2305\n"); +#endif + } diff --git a/board/freescale/common/qixis.c b/board/freescale/common/qixis.c index 1f20223df4..716c93b2c2 100644 --- a/board/freescale/common/qixis.c +++ b/board/freescale/common/qixis.c @@ -31,13 +31,30 @@ #ifdef CONFIG_SYS_I2C_FPGA_ADDR u8 qixis_read_i2c(unsigned int reg) { +#ifndef CONFIG_DM_I2C return i2c_reg_read(CONFIG_SYS_I2C_FPGA_ADDR, reg); +#else + struct udevice *dev; + + if (i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_FPGA_ADDR, 1, &dev)) + return 0xff; + + return dm_i2c_reg_read(dev, reg); +#endif } void qixis_write_i2c(unsigned int reg, u8 value) { u8 val = value; +#ifndef CONFIG_DM_I2C i2c_reg_write(CONFIG_SYS_I2C_FPGA_ADDR, reg, val); +#else + struct udevice *dev; + + if (!i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_FPGA_ADDR, 1, &dev)) + dm_i2c_reg_write(dev, reg, val); +#endif + } #endif diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c index 510d7c266b..bb655ca744 100644 --- a/board/freescale/common/sys_eeprom.c +++ b/board/freescale/common/sys_eeprom.c @@ -149,23 +149,42 @@ static int read_eeprom(void) { int ret; #ifdef CONFIG_SYS_EEPROM_BUS_NUM +#ifndef CONFIG_DM_I2C unsigned int bus; +#endif #endif if (has_been_read) return 0; #ifdef CONFIG_SYS_EEPROM_BUS_NUM +#ifndef CONFIG_DM_I2C bus = i2c_get_bus_num(); i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM); #endif +#endif - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, - (void *)&e, sizeof(e)); +#ifndef CONFIG_DM_I2C + ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + (void *)&e, sizeof(e)); +#else + struct udevice *dev; +#ifdef CONFIG_SYS_EEPROM_BUS_NUM + ret = i2c_get_chip_for_busnum(CONFIG_SYS_EEPROM_BUS_NUM, + CONFIG_SYS_I2C_EEPROM_ADDR, 1, &dev); +#else + ret = i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_EEPROM_ADDR, 1, &dev); +#endif + if (!ret) + ret = dm_i2c_read(dev, 0, (void *)&e, sizeof(e)); +#endif #ifdef CONFIG_SYS_EEPROM_BUS_NUM +#ifndef CONFIG_DM_I2C i2c_set_bus_num(bus); #endif +#endif #ifdef DEBUG show_eeprom(); @@ -199,7 +218,9 @@ static int prog_eeprom(void) int i; void *p; #ifdef CONFIG_SYS_EEPROM_BUS_NUM +#ifndef CONFIG_DM_I2C unsigned int bus; +#endif #endif /* Set the reserved values to 0xFF */ @@ -211,9 +232,11 @@ static int prog_eeprom(void) #endif update_crc(); +#ifndef CONFIG_DM_I2C #ifdef CONFIG_SYS_EEPROM_BUS_NUM bus = i2c_get_bus_num(); i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM); +#endif #endif /* @@ -222,8 +245,26 @@ static int prog_eeprom(void) * complete a given write. */ for (i = 0, p = &e; i < sizeof(e); i += 8, p += 8) { - ret = i2c_write(CONFIG_SYS_I2C_EEPROM_ADDR, i, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, +#ifndef CONFIG_DM_I2C + ret = i2c_write(CONFIG_SYS_I2C_EEPROM_ADDR, i, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, p, min((int)(sizeof(e) - i), 8)); +#else + struct udevice *dev; +#ifdef CONFIG_SYS_EEPROM_BUS_NUM + ret = i2c_get_chip_for_busnum(CONFIG_SYS_EEPROM_BUS_NUM, + CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + &dev); +#else + ret = i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + &dev); +#endif + if (!ret) + ret = dm_i2c_write(dev, i, p, min((int)(sizeof(e) - i), + 8)); +#endif if (ret) break; udelay(5000); /* 5ms write cycle timing */ @@ -233,14 +274,33 @@ static int prog_eeprom(void) /* Verify the write by reading back the EEPROM and comparing */ struct eeprom e2; +#ifndef CONFIG_DM_I2C ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, - CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (void *)&e2, sizeof(e2)); + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + (void *)&e2, sizeof(e2)); +#else + struct udevice *dev; +#ifdef CONFIG_SYS_EEPROM_BUS_NUM + ret = i2c_get_chip_for_busnum(CONFIG_SYS_EEPROM_BUS_NUM, + CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + &dev); +#else + ret = i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + &dev); +#endif + if (!ret) + ret = dm_i2c_read(dev, 0, (void *)&e2, sizeof(e2)); +#endif if (!ret && memcmp(&e, &e2, sizeof(e))) ret = -1; } +#ifndef CONFIG_DM_I2C #ifdef CONFIG_SYS_EEPROM_BUS_NUM i2c_set_bus_num(bus); +#endif #endif if (ret) { @@ -529,8 +589,24 @@ unsigned int get_cpu_board_revision(void) u8 minor; /* 0x05 Board revision, minor */ } be; +#ifndef CONFIG_DM_I2C i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (void *)&be, sizeof(be)); +#else + struct udevice *dev; +#ifdef CONFIG_SYS_EEPROM_BUS_NUM + ret = i2c_get_chip_for_busnum(CONFIG_SYS_EEPROM_BUS_NUM, + CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + &dev); +#else + ret = i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + &dev) +#endif + if (!ret) + dm_i2c_read(dev, 0, (void *)&be, sizeof(be)); +#endif if (be.id != (('C' << 24) | ('C' << 16) | ('I' << 8) | 'D')) return MPC85XX_CPU_BOARD_REV(0, 0); diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c index b804971981..b37f3bf4f8 100644 --- a/board/freescale/common/vid.c +++ b/board/freescale/common/vid.c @@ -61,13 +61,23 @@ static int find_ir_chip_on_i2c(void) u8 byte; int i; const int ir_i2c_addr[] = {0x38, 0x08, 0x09}; +#ifdef CONFIG_DM_I2C + struct udevice *dev; +#endif /* Check all the address */ for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) { i2caddress = ir_i2c_addr[i]; +#ifndef CONFIG_DM_I2C ret = i2c_read(i2caddress, IR36021_MFR_ID_OFFSET, 1, (void *)&byte, sizeof(byte)); +#else + ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, IR36021_MFR_ID_OFFSET, + (void *)&byte, sizeof(byte)); +#endif if ((ret >= 0) && (byte == IR36021_MFR_ID)) return i2caddress; } @@ -103,11 +113,21 @@ static int read_voltage_from_INA220(int i2caddress) int i, ret, voltage_read = 0; u16 vol_mon; u8 buf[2]; +#ifdef CONFIG_DM_I2C + struct udevice *dev; +#endif for (i = 0; i < NUM_READINGS; i++) { +#ifndef CONFIG_DM_I2C ret = i2c_read(I2C_VOL_MONITOR_ADDR, I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&buf, 2); +#else + ret = i2c_get_chip_for_busnum(0, I2C_VOL_MONITOR_ADDR, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, I2C_VOL_MONITOR_BUS_V_OFFSET, + (void *)&buf, 2); +#endif if (ret) { printf("VID: failed to read core voltage\n"); return ret; @@ -136,11 +156,21 @@ static int read_voltage_from_IR(int i2caddress) int i, ret, voltage_read = 0; u16 vol_mon; u8 buf; +#ifdef CONFIG_DM_I2C + struct udevice *dev; +#endif for (i = 0; i < NUM_READINGS; i++) { +#ifndef CONFIG_DM_I2C ret = i2c_read(i2caddress, IR36021_LOOP1_VOUT_OFFSET, 1, (void *)&buf, 1); +#else + ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, IR36021_LOOP1_VOUT_OFFSET, + (void *)&buf, 1); +#endif if (ret) { printf("VID: failed to read vcpu\n"); return ret; @@ -179,17 +209,33 @@ static int read_voltage_from_LTC(int i2caddress) int ret, vcode = 0; u8 chan = PWM_CHANNEL0; +#ifndef CONFIG_DM_I2C /* select the PAGE 0 using PMBus commands PAGE for VDD*/ ret = i2c_write(I2C_VOL_MONITOR_ADDR, PMBUS_CMD_PAGE, 1, &chan, 1); +#else + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(0, I2C_VOL_MONITOR_ADDR, 1, &dev); + if (!ret) + ret = dm_i2c_write(dev, PMBUS_CMD_PAGE, &chan, 1); +#endif if (ret) { printf("VID: failed to select VDD Page 0\n"); return ret; } +#ifndef CONFIG_DM_I2C /*read the output voltage using PMBus command READ_VOUT*/ ret = i2c_read(I2C_VOL_MONITOR_ADDR, PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2); +#else + ret = dm_i2c_read(dev, PMBUS_CMD_READ_VOUT, (void *)&vcode, 2); + if (ret) { + printf("VID: failed to read the volatge\n"); + return ret; + } +#endif if (ret) { printf("VID: failed to read the volatge\n"); return ret; @@ -294,8 +340,18 @@ static int set_voltage_to_IR(int i2caddress, int vdd) vid = DIV_ROUND_UP(vdd - 245, 5); #endif +#ifndef CONFIG_DM_I2C ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET, 1, (void *)&vid, sizeof(vid)); +#else + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); + if (!ret) + ret = dm_i2c_write(dev, IR36021_LOOP1_MANUAL_ID_OFFSET, + (void *)&vid, sizeof(vid)); + +#endif if (ret) { printf("VID: failed to write VID\n"); return -1; @@ -331,8 +387,17 @@ static int set_voltage_to_LTC(int i2caddress, int vdd) vdd & 0xFF, (vdd & 0xFF00) >> 8}; /* Write the desired voltage code to the regulator */ +#ifndef CONFIG_DM_I2C ret = i2c_write(I2C_VOL_MONITOR_ADDR, PMBUS_CMD_PAGE_PLUS_WRITE, 1, (void *)&buff, 5); +#else + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(0, I2C_VOL_MONITOR_ADDR, 1, &dev); + if (!ret) + ret = dm_i2c_write(dev, PMBUS_CMD_PAGE_PLUS_WRITE, + (void *)&buff, 5); +#endif if (ret) { printf("VID: I2C failed to write to the volatge regulator\n"); return -1; @@ -516,14 +581,24 @@ int adjust_vdd(ulong vdd_override) } /* check IR chip work on Intel mode*/ +#ifndef CONFIG_DM_I2C ret = i2c_read(i2caddress, IR36021_INTEL_MODE_OOFSET, 1, (void *)&buf, 1); +#else + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, IR36021_INTEL_MODE_OOFSET, + (void *)&buf, 1); +#endif if (ret) { printf("VID: failed to read IR chip mode.\n"); ret = -1; goto exit; } + if ((buf & IR36021_MODE_MASK) != IR36021_INTEL_MODE) { printf("VID: IR Chip is not used in Intel mode.\n"); ret = -1; @@ -688,9 +763,18 @@ int adjust_vdd(ulong vdd_override) } /* check IR chip work on Intel mode*/ +#ifndef CONFIG_DM_I2C ret = i2c_read(i2caddress, IR36021_INTEL_MODE_OOFSET, 1, (void *)&buf, 1); +#else + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, IR36021_INTEL_MODE_OOFSET, + (void *)&buf, 1); +#endif if (ret) { printf("VID: failed to read IR chip mode.\n"); ret = -1; diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c index 3dfbfebedc..163b42dda4 100644 --- a/board/freescale/lx2160a/lx2160a.c +++ b/board/freescale/lx2160a/lx2160a.c @@ -74,7 +74,15 @@ int select_i2c_ch_pca9547(u8 ch) { int ret; +#ifndef CONFIG_DM_I2C ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); +#else + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(0, I2C_MUX_PCA_ADDR_PRI, 1, &dev); + if (!ret) + ret = dm_i2c_write(dev, 0, &ch, 1); +#endif if (ret) { puts("PCA: failed to select proper channel\n"); return ret; diff --git a/drivers/ddr/fsl/main.c b/drivers/ddr/fsl/main.c index e1f69a1d25..ac0783b428 100644 --- a/drivers/ddr/fsl/main.c +++ b/drivers/ddr/fsl/main.c @@ -92,7 +92,10 @@ static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) uint8_t dummy = 0; #endif +#ifndef CONFIG_DM_I2C i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); +#endif + #ifdef CONFIG_SYS_FSL_DDR4 /* @@ -101,6 +104,7 @@ static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) * To access the upper 256 bytes, we need to set EE page address to 1 * See Jedec standar No. 21-C for detail */ +#ifndef CONFIG_DM_I2C i2c_write(SPD_SPA0_ADDRESS, 0, 1, &dummy, 1); ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, 256); if (!ret) { @@ -111,8 +115,38 @@ static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) (int)sizeof(generic_spd_eeprom_t) - 256)); } #else + struct udevice *dev; + int read_len = min(256, (int)sizeof(generic_spd_eeprom_t) - 256); + + ret = i2c_get_chip_for_busnum(0, SPD_SPA0_ADDRESS, 1, &dev); + if (!ret) + dm_i2c_write(dev, 0, &dummy, 1); + ret = i2c_get_chip_for_busnum(0, i2c_address, 1, &dev); + if (!ret) { + if (!dm_i2c_read(dev, 0, (uchar *)spd, 256)) { + if (!i2c_get_chip_for_busnum(0, SPD_SPA1_ADDRESS, + 1, &dev)) + dm_i2c_write(dev, 0, &dummy, 1); + if (!i2c_get_chip_for_busnum(0, i2c_address, 1, &dev)) + ret = dm_i2c_read(dev, 0, + (uchar *)((ulong)spd + 256), + read_len); + } + } +#endif + +#else + +#ifndef CONFIG_DM_I2C ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, - sizeof(generic_spd_eeprom_t)); + sizeof(generic_spd_eeprom_t)); +#else + ret = i2c_get_chip_for_busnum(0, i2c_address, 1, &dev); + if (!ret) + ret = dm_i2c_read(dev, 0, (uchar *)spd, + sizeof(generic_spd_eeprom_t)); +#endif + #endif if (ret) {