From: Stefano Babic Date: Tue, 16 Mar 2010 16:22:21 +0000 (+0100) Subject: Add SPI support to mx51evk board X-Git-Tag: v2010.09-rc1~1^2~19^2~9^2 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=0cf7d2440e1aa91ca65f1fc08ba309184d376da6;p=oweals%2Fu-boot.git Add SPI support to mx51evk board The patch adds SPI devices to the mx51evk board. The MC13892 chip (PMIC) is supported. Signed-off-by: Stefano Babic --- diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 3d89be39f2..75d642bf42 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -27,9 +27,12 @@ #include #include #include +#include #include #include #include +#include +#include #include "mx51evk.h" DECLARE_GLOBAL_DATA_PTR; @@ -147,6 +150,130 @@ static void setup_iomux_fec(void) mxc_iomux_set_pad(MX51_PIN_NANDF_D11, 0x2180); } +#ifdef CONFIG_MXC_SPI +static void setup_iomux_spi(void) +{ + /* 000: Select mux mode: ALT0 mux port: MOSI of instance: ecspi1 */ + mxc_request_iomux(MX51_PIN_CSPI1_MOSI, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_MOSI, 0x105); + + /* 000: Select mux mode: ALT0 mux port: MISO of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_MISO, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_MISO, 0x105); + + /* de-select SS1 of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_SS1, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SS1, 0x85); + + /* 000: Select mux mode: ALT0 mux port: SS0 ecspi1 */ + mxc_request_iomux(MX51_PIN_CSPI1_SS0, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SS0, 0x185); + + /* 000: Select mux mode: ALT0 mux port: RDY of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_RDY, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_RDY, 0x180); + + /* 000: Select mux mode: ALT0 mux port: SCLK of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_SCLK, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SCLK, 0x105); +} +#endif + +static void power_init(void) +{ + unsigned int val; + unsigned int reg; + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE; + + /* Write needed to Power Gate 2 register */ + val = pmic_reg_read(REG_POWER_MISC); + val &= ~PWGT2SPIEN; + pmic_reg_write(REG_POWER_MISC, val); + + /* Write needed to update Charger 0 */ + pmic_reg_write(REG_CHARGE, VCHRG0 | VCHRG1 | VCHRG2 | + ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | ICHRGTR0 | + OVCTRL1 | UCHEN | CHRGLEDEN | CYCLB); + + /* power up the system first */ + pmic_reg_write(REG_POWER_MISC, PWUP); + + /* Set core voltage to 1.1V */ + val = pmic_reg_read(REG_SW_0); + val = (val & (~0x1F)) | 0x14; + pmic_reg_write(REG_SW_0, val); + + /* Setup VCC (SW2) to 1.25 */ + val = pmic_reg_read(REG_SW_1); + val = (val & (~0x1F)) | 0x1A; + pmic_reg_write(REG_SW_1, val); + + /* Setup 1V2_DIG1 (SW3) to 1.25 */ + val = pmic_reg_read(REG_SW_2); + val = (val & (~0x1F)) | 0x1A; + pmic_reg_write(REG_SW_2, val); + udelay(50); + + /* Raise the core frequency to 800MHz */ + writel(0x0, &mxc_ccm->cacrr); + + /* Set switchers in Auto in NORMAL mode & STANDBY mode */ + /* Setup the switcher mode for SW1 & SW2*/ + val = pmic_reg_read(REG_SW_4); + val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) | + (SWMODE_MASK << SWMODE2_SHIFT))); + val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) | + (SWMODE_AUTO_AUTO << SWMODE2_SHIFT); + pmic_reg_write(REG_SW_4, val); + + /* Setup the switcher mode for SW3 & SW4 */ + val = pmic_reg_read(REG_SW_5); + val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) | + (SWMODE_MASK << SWMODE4_SHIFT))); + val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) | + (SWMODE_AUTO_AUTO << SWMODE4_SHIFT); + pmic_reg_write(REG_SW_5, val); + + /* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */ + val = pmic_reg_read(REG_SETTING_0); + val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK); + val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6; + pmic_reg_write(REG_SETTING_0, val); + + /* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */ + val = pmic_reg_read(REG_SETTING_1); + val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK); + val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775; + pmic_reg_write(REG_SETTING_1, val); + + /* Configure VGEN3 and VCAM regulators to use external PNP */ + val = VGEN3CONFIG | VCAMCONFIG; + pmic_reg_write(REG_MODE_1, val); + udelay(200); + + reg = readl(GPIO2_BASE_ADDR + 0x0); + reg &= ~0x4000; /* Lower reset line */ + writel(reg, GPIO2_BASE_ADDR + 0x0); + + reg = readl(GPIO2_BASE_ADDR + 0x4); + reg |= 0x4000; /* configure GPIO lines as output */ + writel(reg, GPIO2_BASE_ADDR + 0x4); + + /* Reset the ethernet controller over GPIO */ + writel(0x1, IOMUXC_BASE_ADDR + 0x0AC); + + /* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */ + val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG | + VVIDEOEN | VAUDIOEN | VSDEN; + pmic_reg_write(REG_MODE_1, val); + + udelay(500); + + reg = readl(GPIO2_BASE_ADDR + 0x0); + reg |= 0x4000; + writel(reg, GPIO2_BASE_ADDR + 0x0); +} + #ifdef CONFIG_FSL_ESDHC int board_mmc_getcd(u8 *cd, struct mmc *mmc) { @@ -284,9 +411,21 @@ int board_init(void) setup_iomux_uart(); setup_iomux_fec(); + return 0; } +#ifdef BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_MXC_SPI + setup_iomux_spi(); + power_init(); +#endif + return 0; +} +#endif + int checkboard(void) { puts("Board: MX51EVK "); diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index 3626df73df..86a4731a69 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -54,12 +54,27 @@ /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_SIZE 128 +#define BOARD_LATE_INIT + /* * Hardware drivers */ #define CONFIG_MXC_UART #define CONFIG_SYS_MX51_UART1 +/* + * SPI Configs + * */ +#define CONFIG_CMD_SPI + +#define CONFIG_MXC_SPI + +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 0 +#define CONFIG_FSL_PMIC_CS 0 +#define CONFIG_FSL_PMIC_CLK 2500000 +#define CONFIG_FSL_PMIC_MODE (SPI_CPOL | SPI_CS_HIGH) + /* * MMC Configs * */