From: Piotr Dymacz Date: Mon, 16 Nov 2015 00:03:21 +0000 (+0100) Subject: Add qca_gpio_init.S file with lowlevel initialization of GPIO, for platforms based... X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=087478ec62201b1db4009990c683773d96f56384;p=oweals%2Fu-boot_mod.git Add qca_gpio_init.S file with lowlevel initialization of GPIO, for platforms based on QC/A SOCs --- diff --git a/u-boot/cpu/mips/ar7240/Makefile b/u-boot/cpu/mips/ar7240/Makefile index 350f49a..63ff167 100644 --- a/u-boot/cpu/mips/ar7240/Makefile +++ b/u-boot/cpu/mips/ar7240/Makefile @@ -3,13 +3,17 @@ include $(TOPDIR)/config.mk LIB = lib$(SOC).a START = +OBJS = +SOBJS = -OBJS = meminit.o +OBJS += meminit.o OBJS += qca_common.o OBJS += qca_clocks.o +SOBJS += qca_gpio_init.o ifeq ($(BOARD), ap121) OBJS += qca_hs_uart.o + OBJS += ag7240.o SOBJS += hornet_ddr_init.o else OBJS += qca_ls_uart.o @@ -17,12 +21,8 @@ endif ifeq ($(BOARD), db12x) OBJS += ag934x.o -else - OBJS += ag7240.o endif -SOBJS += - all: .depend $(START) $(LIB) $(LIB): $(OBJS) $(SOBJS) $(OBJS-0) diff --git a/u-boot/cpu/mips/ar7240/qca_gpio_init.S b/u-boot/cpu/mips/ar7240/qca_gpio_init.S new file mode 100644 index 0000000..96ea76b --- /dev/null +++ b/u-boot/cpu/mips/ar7240/qca_gpio_init.S @@ -0,0 +1,344 @@ +/* + * This file contains code used for lowlevel initialization + * of GPIO, on supported Qualcomm/Atheros platforms + * + * Copyright (C) 2015 Piotr Dymacz + * + * SPDX-License-Identifier:GPL-2.0 + */ + +#include +#include +#include +#include +#include +#include + +.globl lowlevel_gpio_init +.ent lowlevel_gpio_init + +lowlevel_gpio_init: + +/* + * JTAG and UART init + */ +#if (SOC_TYPE & QCA_AR934X_SOC) || \ + (SOC_TYPE & QCA_QCA955X_SOC) || \ + (SOC_TYPE & QCA_QCA953X_SOC) + /* + * Disable JTAG (bit 1 set) and ALL clock observation (bit 2~9 reset) + * Do not do this in RAM version! + */ + li t8, QCA_GPIO_FUNC_REG + + #ifndef CONFIG_SKIP_LOWLEVEL_INIT + li t9, QCA_GPIO_FUNC_JTAG_DIS_MASK + #else + li t9, 0x0 + #endif + sw t9, 0(t8) + + /* + * Setup GPIOs for LS UART: + * - TX: GPIO10 + * - RX: GPIO9 + * + * TODO: + * - allow select LS or HS UART on platforms which support both + * - allow select other than default GPIOs for LS/HS UART pins + */ + + /* GPIO10 as output, GPIO9 as input */ + li t8, QCA_GPIO_OE_REG + lw t9, 0(t8) + and t9, t9, ~GPIO10 + or t9, t9, GPIO9 + sw t9, 0(t8) + + /* Set LSUART_TXD on GPIO10 */ + li t8, QCA_GPIO_OUT_FUNC2_REG + lw t9, 0(t8) + and t9, t9, ~QCA_GPIO_OUT_FUNCX_GPIO10_EN_MASK + or t9, t9, (QCA_GPIO_OUT_MUX_LSUART_TXD_VAL << \ + QCA_GPIO_OUT_FUNCX_GPIO10_EN_SHIFT) + sw t9, 0(t8) + + /* Set LSUART_RXD on GPIO9 */ + li t8, QCA_GPIO_IN_EN0_REG + lw t9, 0(t8) + and t9, t9, ~QCA_GPIO_IN_EN0_LSUART_RXD_MASK + or t9, t9, (9 << QCA_GPIO_IN_EN0_LSUART_RXD_SHIFT) + sw t9, 0(t8) +#endif + +/* + * General configuration of GPIO (buttons, LEDs, default value, etc.) + */ +#if defined(CONFIG_FOR_TPLINK_WDR3600_WDR43X0_V1) + /* + * LEDs and buttons GPIOs on WDR3600/WDR43x0 v1: + * + * 11 => USB1 LED + * 12 => USB2 LED + * 13 => WLAN2G + * 14 => SYS + * 15 => QSS + * 21 => USB2 POWER (active high) + * 22 => USB1 POWER (active high) + * + * 16 => Reset button + * 17 => Wi-Fi ON/OFF switch + * + * All OUT GPIOs are active LOW if not stated otherwise + */ + + /* GPIO Init */ + li t8, QCA_GPIO_OE_REG + lw t9, 0(t8) + /* Set GPIOs 11~15 and 21~22 as outputs */ + and t9, t9, ~(GPIO11 | GPIO12 | GPIO13 | \ + GPIO14 | GPIO15 | GPIO21 | GPIO22) + /* Set GPIOs 16~17 as inputs */ + or t9, t9, (GPIO16 | GPIO17) + sw t9, 0(t8) + + /* Set GPIO function for GPIO 11 */ + li t8, QCA_GPIO_OUT_FUNC2_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO11_EN_MASK) + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 12~15 */ + li t8, QCA_GPIO_OUT_FUNC3_REG + li t9, 0x0 + sw t9, 0(t8) + + /* Turn on all LEDS and power on both USB */ + li t8, QCA_GPIO_SET_REG + li t9, (GPIO21 | GPIO22) + sw t9, 0(t8) + + /* Wait for a while, for LEDs bootup blink */ + li t8, 0 + li t9, 0x70000 + +1: + addi t8, t8, 1 + bne t8, t9, 1b + nop + + /* Turn off all LEDs */ + li t8, QCA_GPIO_SET_REG + li t9, (GPIO11 | GPIO12 | GPIO13 | \ + GPIO14 | GPIO15 | GPIO21 | GPIO22) + sw t9, 0(t8) + +#elif defined(CONFIG_FOR_TPLINK_WDR3500_V1) + /* + * LEDs and buttons GPIOs on WDR3500 v1: + * + * 11 => USB LED + * 12 => USB POWER (active high) + * 13 => WLAN2G + * 14 => SYS + * 15 => QSS + * 18 => WAN + * 19 => LAN1 + * 20 => LAN2 + * 21 => LAN3 + * 22 => LAN4 + * + * 16 => Reset button + * 17 => Wi-Fi ON/OFF switch + * + * All OUT GPIOs are active LOW if not stated otherwise + */ + + /* GPIO Init */ + li t8, QCA_GPIO_OE_REG + lw t9, 0(t8) + /* Set GPIOs 11~15 and 18~22 as outputs */ + and t9, t9, ~(GPIO11 | GPIO12 | GPIO13 | GPIO14 | GPIO15 | \ + GPIO18 | GPIO19 | GPIO20 | GPIO21 | GPIO22) + /* Set GPIOs 16~17 as inputs */ + or t9, t9, (GPIO16 | GPIO17) + sw t9, 0(t8) + + /* Set GPIO function for GPIO 11 */ + li t8, QCA_GPIO_OUT_FUNC2_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO11_EN_MASK) + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 12~15 */ + li t8, QCA_GPIO_OUT_FUNC3_REG + li t9, 0x0 + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 18~19 */ + li t8, QCA_GPIO_OUT_FUNC4_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO18_EN_MASK | \ + QCA_GPIO_OUT_FUNCX_GPIO19_EN_MASK) + sw t9, 0(t8) + + /* Turn off all LEDs and turn on power on USB */ + li t8, QCA_GPIO_SET_REG + li t9, (GPIO11 | GPIO12 | GPIO13 | GPIO14 | GPIO15 | \ + GPIO18 | GPIO19 | GPIO20 | GPIO21 | GPIO22) + sw t9, 0(t8) + +#elif defined(CONFIG_FOR_TPLINK_WR841N_V8) + /* + * LEDs and buttons GPIOs on WR841N/D v8: + * + * 12 => LAN4 + * 13 => WLAN + * 14 => SYS + * 15 => QSS + * 18 => WAN + * 19 => LAN1 + * 20 => LAN2 + * 21 => LAN3 + * + * 16 => Wi-Fi ON/OFF switch + * 17 => Reset button + * + * All OUT GPIOs are active LOW if not stated otherwise + */ + + /* GPIOs init */ + li t8, QCA_GPIO_OE_REG + lw t9, 0(t8) + /* Set GPIOs 12~15 and 18~21 as outputs */ + and t9, t9, ~(GPIO12 | GPIO13 | GPIO14 | GPIO15 | \ + GPIO18 | GPIO19 | GPIO20 | GPIO21) + /* Set GPIOs 16~17 as inputs */ + or t9, t9, (GPIO16 | GPIO17) + sw t9, 0(t8) + + /* Set gpio function for GPIOs 12~15 */ + li t8, QCA_GPIO_OUT_FUNC3_REG + li t9, 0x0 + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 18~19 */ + li t8, QCA_GPIO_OUT_FUNC4_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO18_EN_MASK | \ + QCA_GPIO_OUT_FUNCX_GPIO19_EN_MASK) + sw t9, 0(t8) + + /* Turn off all LEDs */ + li t8, QCA_GPIO_SET_REG + li t9, (GPIO12 | GPIO13 | GPIO14 | GPIO15 | \ + GPIO18 | GPIO19 | GPIO20 | GPIO21) + sw t9, 0(t8) + +#elif defined(CONFIG_FOR_TPLINK_MR3420_V2) + /* + * LEDs and buttons GPIOs on MR3420 v2: + * + * 4 => USB Power (active high) + * 11 => USB/3G LED + * 12 => LAN4 + * 13 => WLAN + * 14 => SYS + * 15 => QSS + * 18 => WAN + * 19 => LAN1 + * 20 => LAN2 + * 21 => LAN3 + * + * 16 => WPS button + * 17 => Reset button + * + * All OUT GPIOs are active LOW if not stated otherwise + */ + + /* GPIOs init */ + li t8, QCA_GPIO_OE_REG + lw t9, 0(t8) + /* Set GPIOs 4, 11~15 and 18~21 as outputs */ + and t9, t9, ~(GPIO4 | GPIO11 | GPIO12 | GPIO13 | GPIO14 | \ + GPIO15 | GPIO18 | GPIO19 | GPIO20 | GPIO21) + /* Set GPIOs 16~17 as inputs */ + or t9, t9, (GPIO16 | GPIO17) + sw t9, 0(t8) + + /* Set GPIO function for GPIO 4 */ + li t8, QCA_GPIO_OUT_FUNC1_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO4_EN_MASK) + sw t9, 0(t8) + + /* Set GPIO function for GPIO 11 */ + li t8, QCA_GPIO_OUT_FUNC2_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO11_EN_MASK) + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 12~15 */ + li t8, QCA_GPIO_OUT_FUNC3_REG + li t9, 0x0 + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 18~19 */ + li t8, QCA_GPIO_OUT_FUNC4_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO18_EN_MASK | \ + QCA_GPIO_OUT_FUNCX_GPIO19_EN_MASK) + sw t9, 0(t8) + + /* Turn off all LEDs and turn on power on USB */ + li t8, QCA_GPIO_SET_REG + li t9, (GPIO4 | GPIO11 | GPIO12 | GPIO13 | GPIO14 | \ + GPIO15 | GPIO18 | GPIO19 | GPIO20 | GPIO21) + sw t9, 0(t8) + +#elif defined(CONFIG_FOR_TPLINK_WA830RE_V2_WA801ND_V2) + /* + * LEDs and buttons GPIOs on WA830REv2 and WA801ND v2: + * + * 13 => WLAN + * 14 => SYS + * 15 => QSS + * 18 => LAN + * + * 16 => Range Extender + * 17 => Reset button + * + * All OUT GPIOs are active LOW if not stated otherwise + */ + + /* GPIOs init */ + li t8, QCA_GPIO_OE_REG + lw t9, 0(t8) + /* Set GPIOs 13~15 and 18 as outputs */ + and t9, t9, ~(GPIO13 | GPIO14 | GPIO15 | GPIO18) + /* Set GPIOs 16~17 as inputs */ + or t9, t9, (GPIO16 | GPIO17) + sw t9, 0(t8) + + /* Set GPIO function for GPIOs 13~15 */ + li t8, QCA_GPIO_OUT_FUNC3_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO13_EN_MASK | \ + QCA_GPIO_OUT_FUNCX_GPIO14_EN_MASK | \ + QCA_GPIO_OUT_FUNCX_GPIO15_EN_MASK) + sw t9, 0(t8) + + /* Set GPIO function for GPIO 18 */ + li t8, QCA_GPIO_OUT_FUNC4_REG + lw t9, 0(t8) + and t9, t9, ~(QCA_GPIO_OUT_FUNCX_GPIO18_EN_MASK) + sw t9, 0(t8) + + /* Turn off all LEDs */ + li t8, QCA_GPIO_SET_REG + li t9, (GPIO13 | GPIO14 | GPIO15 | GPIO18) + sw t9, 0(t8) +#endif + + j ra + .end lowlevel_gpio_init