From: Mathew McBride Date: Mon, 30 Apr 2018 12:42:39 +0000 (+1000) Subject: layerscape: add Traverse LS1043-S support X-Git-Tag: v19.07.0-rc1~2994 X-Git-Url: https://git.librecmc.org/?a=commitdiff_plain;h=08714738d2c8d7710f8fd2b7deac795f49e7d7c2;p=oweals%2Fopenwrt.git layerscape: add Traverse LS1043-S support The Traverse LS1043-S board is a router board based on NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+, as well as miniPCIe and M.2 LTE. Unlike the Layerscape reference boards, the LS1043-S board has NAND flash and uses the mainline U-Boot. This patch implements support for the LS1043-S board, as well as the earlier LS1043-V board. It is our intention that all boards in this family (LS1043-S and later, Five64) will boot the same binary. Not included in this patchset are the hwmon drivers not in the kernel (emc1704,pac1934) or the bootloader. Signed-off-by: Mathew McBride --- diff --git a/target/linux/layerscape/base-files/etc/board.d/01_led b/target/linux/layerscape/base-files/etc/board.d/01_led new file mode 100755 index 0000000000..b9b62a07e0 --- /dev/null +++ b/target/linux/layerscape/base-files/etc/board.d/01_led @@ -0,0 +1,25 @@ +#!/bin/sh +# +# Copyright (C) 2015 OpenWrt.org +# + +. /lib/functions/uci-defaults.sh + +board_config_update + +board=$(board_name) + +case "$board" in +traverse,ls1043v) + ucidef_set_led_netdev "wan" "WAN LED" "ls1043v:yellow:wan" "eth4" + ;; +traverse,ls1043s) + ucidef_set_led_netdev "wan" "WAN LED" "ls1043s:yellow:wan" "eth4" + ucidef_set_led_netdev "xgact" "10G Activity" "ls1043s:yellow:10gact" "eth6" + ucidef_set_led_netdev "xglink" "10G Link" "ls1043s:green:10glink" "eth6" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/layerscape/base-files/etc/board.d/02_network b/target/linux/layerscape/base-files/etc/board.d/02_network new file mode 100755 index 0000000000..c50b4a346a --- /dev/null +++ b/target/linux/layerscape/base-files/etc/board.d/02_network @@ -0,0 +1,21 @@ +#!/bin/sh + +. /lib/functions/system.sh +. /lib/functions/uci-defaults.sh + +board_config_update + +case "$(board_name)" in + traverse,ls1043v) + ucidef_set_interface_lan "eth0 eth1 eth2 eth3" + ucidef_set_interface_wan "eth4" + ;; + traverse,ls1043s) + ucidef_set_interface_lan "eth0 eth1 eth2 eth3 eth6" + ucidef_set_interface_wan "eth4" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches b/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches new file mode 100755 index 0000000000..7f9da08668 --- /dev/null +++ b/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches @@ -0,0 +1,28 @@ +#!/bin/sh +# +# Copyright (C) 2015 OpenWrt.org +# + +. /lib/functions/uci-defaults.sh + +board_config_update + +board=$(board_name) + +case "$board" in +traverse,ls1043v) + ucidef_add_gpio_switch "lte_reset" "LTE Reset" "377" + ucidef_add_gpio_switch "lte_disable" "LTE Airplane mode" "378" + ;; +traverse,ls1043s) + ucidef_add_gpio_switch "tensfp_txdisable" "SFP+ TX Disable" "378" + ucidef_add_gpio_switch "gigsfp_txdisable" "SFP TX Disable" "381" + ucidef_add_gpio_switch "lte_reset" "LTE Reset" "502" + ucidef_add_gpio_switch "lte_disable" "LTE Airplane Mode" "394" + ucidef_add_gpio_switch "lte_power" "LTE Power" "395" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth b/target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth new file mode 100644 index 0000000000..c4feec42bc --- /dev/null +++ b/target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth @@ -0,0 +1,28 @@ +#!/bin/sh + +reorder_layerscape_interfaces() { + if [ ! -f /tmp/sysinfo/board_name ]; then + echo "No board name found, not doing reorder_layerscape_interfaces" + return 0 + fi + + board=$(cat /tmp/sysinfo/board_name) + case "$board" in + "traverse,ls1043v" | \ + "traverse,ls1043s") + + # Reorder ethernet interfaces to match the physical order + ip link set eth2 name fm1-mac3 + ip link set eth4 name eth2 + ip link set eth3 name fm1-mac4 + ip link set eth5 name eth3 + ip link set fm1-mac3 name eth4 + ip link set fm1-mac4 name eth5 + ;; + default) + echo "Unknown board $board" + ;; + esac +} + +boot_hook_add preinit_main reorder_layerscape_interfaces diff --git a/target/linux/layerscape/base-files/lib/upgrade/platform.sh b/target/linux/layerscape/base-files/lib/upgrade/platform.sh new file mode 100644 index 0000000000..9cc960a5fc --- /dev/null +++ b/target/linux/layerscape/base-files/lib/upgrade/platform.sh @@ -0,0 +1,94 @@ +#!/bin/sh +# +# Copyright 2015-2018 Traverse Technologies +# +platform_do_upgrade_traverse_nandubi() { + bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}') + newbootsys=2 + if [ "$bootsys" -eq "2" ]; then + newbootsys=1 + fi + mkdir -p /tmp/image + cd /tmp/image + get_image "$1" > image.tar + ls -la image.tar + files=$(tar -tf image.tar) + echo "Files in image:" + echo $files + for f in $files + do + part_name=$(echo $f | awk -F '/' '{{print $2}}') + if [ -z "$part_name" ] || [ "$part_name" = "CONTROL" ]; then + continue + fi + + [ "$part_name" = "root" ] && part_name="rootfs" + + volume=$part_name + if [ "$part_name" = "kernel" ] || [ "$part_name" = "rootfs" ]; then + volume="${part_name}${newbootsys}" + fi + volume_id=$(ubinfo -d 0 --name $volume | awk '/Volume ID/ {print $3}') + file_size=$(tar -tvf image.tar $f | awk '{{print $3}}') + echo "$f size $file_size" + tar -xOf image.tar $f | ubiupdatevol -s $file_size /dev/ubi0_$volume_id - + + echo "$volume upgraded" + done + fw_setenv bootsys $newbootsys + echo "Upgrade complete" +} +platform_copy_config() { + bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}') + rootvol=rootfs$bootsys + volume_id=$(ubinfo -d 0 --name $rootvol | awk '/Volume ID/ {print $3}') + mkdir -p /mnt/oldsys + mount -t ubifs -o rw,noatime /dev/ubi0_$volume_id /mnt/oldsys + cp -af "$CONF_TAR" /mnt/oldsys + umount /mnt/oldsys +} +platform_check_image() { + local board=$(board_name) + + case "$board" in + traverse,ls1043v | \ + traverse,ls1043s | \ + traverse,five64) + local tar_file="$1" + local kernel_length=$( (tar xf $tar_file sysupgrade-traverse-five64/kernel -O | wc -c) 2> /dev/null) + local rootfs_length=$( (tar xf $tar_file sysupgrade-traverse-five64/root -O | wc -c) 2> /dev/null) + [ "$kernel_length" -eq 0 -o "$rootfs_length" -eq 0 ] && { + echo "The upgrade image is corrupt." + return 1 + } + return 0 + ;; + *) + echo "Sysupgrade is not currently supported on $board" + ;; + esac + + return 1 +} +platform_do_upgrade() { + local board=$(board_name) + + case "$board" in + traverse,ls1043v | \ + traverse,ls1043s | \ + traverse,five64) + platform_do_upgrade_traverse_nandubi "$ARGV" + ;; + *) + echo "Sysupgrade is not currently supported on $board" + ;; + esac +} +platform_pre_upgrade() { + # Force the creation of fw_printenv.lock + mkdir -p /var/lock + touch /var/lock/fw_printenv.lock + + export RAMFS_COPY_BIN="/usr/sbin/fw_printenv /usr/sbin/fw_setenv /usr/sbin/ubinfo /bin/echo ${RAMFS_COPY_BIN}" + export RAMFS_COPY_DATA="/etc/fw_env.config /var/lock/fw_printenv.lock ${RAMFS_COPY_DATA}" +} diff --git a/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts b/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts new file mode 100644 index 0000000000..e2d6bc1848 --- /dev/null +++ b/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts @@ -0,0 +1,332 @@ +/* + * Device Tree Include file for Traverse LS1043S board. + * + * Copyright 2014-2015, Freescale Semiconductor + * Copyright 2017-2018, Traverse Technologies + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "fsl-ls1043a.dtsi" +#include +#include + +/ { + model = "Traverse LS1043S"; + compatible = "traverse,ls1043s"; + + aliases { + crypto = &crypto; + ethernet0 = &EMAC0; + ethernet1 = &EMAC1; + ethernet2 = &EMAC2; + ethernet3 = &EMAC3; + ethernet4 = &EMAC4; + ethernet5 = &EMAC5; + }; + + leds { + compatible = "gpio-leds"; + gpio0 { + label = "ls1043s:green:user0"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + }; + gpio1 { + label = "ls1043s:green:user1"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + }; + /* LED D17 */ + gpio2 { + label = "ls1043s:green:wan"; + gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; + }; + gpio3 { + label = "ls1043s:yellow:wan"; + gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + }; + /* LED D18 */ + gpio4 { + label = "ls1043s:green:mgmt"; + gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; + }; + gpio5 { + label = "ls1043s:yellow:mgmt"; + gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + }; + /* LED D6 */ + gpio6 { + label = "ls1043s:green:user2"; + gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>; + }; + + /* SFP+ LEDs - these are for chassis + * with lightpipes only + */ + teng_act { + label = "ls1043s:yellow:10gact"; + gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; + }; + + teng_link { + label = "ls1043s:green:10glink"; + gpios = <&gpio4 1 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <1000>; + /* This button may not be loaded on all boards */ + button@0 { + label = "Front button"; + linux,code = ; + gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + }; + /* This is wired to header S3 */ + button@1 { + label = "Rear button"; + linux,code = ; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&esdhc { + mmc-hs200-1_8v; + sd-uhs-sdr104; + sd-uhs-sdr50; + sd-uhs-sdr25; + sd-uhs-sdr12; +}; + +&i2c0 { + status = "okay"; + rtc@6f { + compatible = "intersil,isl1208"; + reg = <0x6f>; + }; + + sfp_pca9534: pca9534@24 { + compatible = "ti,tca9534", "nxp,pca9534"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x24>; + gpio-base = <100>; + }; + + controller@50 { + compatible = "traverse,controller"; + reg = <0x50>; + }; + + ds125df111@18 { + compatible = "ti,ds125df111"; + reg = <0x18>; + }; + + emc1704@4c { + compatible = "microchip,emc1704"; + reg = <0x4c>; + }; + + pac1934@16 { + compatible = "microchip,pac1934"; + reg = <0x16>; + /* Monitoring 3.3V, 5V, Vin/12V (voltage only), Vbat/RTC (voltage only) */ + shunt-resistors = <4000 12000 0 0>; + }; + + pmic@8 { + compatible = "freescale,mc34vr500"; + reg = <0x08>; + }; +}; + +/* I2C Bus for SFP EEPROM and control + * These are multiplexed so + * they don't collide when loaded + */ +&i2c3 { + status = "okay"; + i2c-switch@70 { + compatible = "nxp,pca9540"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + gigsfp_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + tensfp_i2c: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + /* Only NAND flash is used on this board */ + ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>; + + nand@1,0 { + compatible = "fsl,ifc-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x10000>; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; + +#include "fsl-ls1043-post.dtsi" + +&fman0 { + EMAC0: ethernet@e0000 { + phy-handle = <&qsgmii_phy1>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 01]; + }; + + EMAC1: ethernet@e2000 { + phy-handle = <&qsgmii_phy2>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 02]; + }; + + EMAC2: ethernet@e8000 { + phy-handle = <&qsgmii_phy3>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 03]; + }; + + EMAC3: ethernet@ea000 { + phy-handle = <&qsgmii_phy4>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 04]; + }; + + /* SFP via AR8031 + * We treat this as a fixed-link as the + * AR8031 is hard-configured into + * 1000BASE-X mode + * Should MII control be desired, remove + * fixed-link and add + * phy-handle = <&rgmii_phy1>; + */ + EMAC4: ethernet@e4000 { + phy-connection-type = "rgmii"; + local-mac-address = [0A 00 00 00 00 05]; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + /* Connection to Expansion (M.2) slot + * Future WAN (i.e xDSL) plugin + */ + EMAC5: ethernet@e6000 { + phy-connection-type = "rgmii-id"; + local-mac-address = [00 00 00 00 00 06]; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + /* 10G SFP+ interface + * This can also run at 1.25 and 2.5G with + * the appropriate SerDes protocol setting in RCW + */ + TENSFP: ethernet@f0000 { + status = "okay"; + phy-connection-type = "xgmii"; + fixed-link { + speed = <10000>; + full-duplex; + }; + }; + + mdio@fc000 { + rgmii_phy1: ethernet-phy@2 { + reg = <0x2>; + }; + qsgmii_phy1: ethernet-phy@4 { + reg = <0x4>; + }; + qsgmii_phy2: ethernet-phy@5 { + reg = <0x5>; + }; + qsgmii_phy3: ethernet-phy@6 { + reg = <0x6>; + }; + qsgmii_phy4: ethernet-phy@7 { + reg = <0x7>; + }; + }; +}; + +/* No QUICC engine functions on this board - + * pins are used for other functions (GPIO, I2C etc.) + */ +&uqe { + status = "disabled"; +}; + +/* LS1043S does not use the QorIQ AHCI + * controller. + */ +&sata { + status = "disabled"; +}; diff --git a/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts b/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts new file mode 100644 index 0000000000..de9aa62d2f --- /dev/null +++ b/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts @@ -0,0 +1,253 @@ +/* + * Device Tree Include file for Traverse LS1043V board. + * + * Copyright 2014-2015, Freescale Semiconductor + * Copyright 2017, Traverse Technologies + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "fsl-ls1043a.dtsi" +#include +#include + +/ { + model = "Traverse LS1043V"; + compatible = "traverse,ls1043v"; + + aliases { + crypto = &crypto; + ethernet0 = &EMAC0; + ethernet1 = &EMAC1; + ethernet2 = &EMAC2; + ethernet3 = &EMAC3; + ethernet4 = &EMAC4; + ethernet5 = &EMAC5; + pca9555 = &pca9555; + }; + + leds { + compatible = "gpio-leds"; + gpio0 { + label = "ls1043v:green:user0"; + gpios = <&pca9555 0 GPIO_ACTIVE_LOW>; + }; + gpio1 { + label = "ls1043v:yellow:user0"; + gpios = <&pca9555 1 GPIO_ACTIVE_LOW>; + }; + gpio2 { + label = "ls1043v:green:user1"; + gpios = <&pca9555 2 GPIO_ACTIVE_LOW>; + }; + gpio3 { + label = "ls1043v:yellow:user1"; + gpios = <&pca9555 3 GPIO_ACTIVE_LOW>; + }; + gpio4 { + label = "ls1043v:green:user2"; + gpios = <&pca9555 4 GPIO_ACTIVE_HIGH>; + }; + gpio5 { + label = "ls1043v:yellow:wlan"; + gpios = <&pca9555 5 GPIO_ACTIVE_HIGH>; + }; + gpio6 { + label = "ls1043v:yellow:wan"; + gpios = <&pca9555 6 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <1000>; + button@0 { + label = "Front button"; + linux,code = ; + gpios = <&pca9555 14 GPIO_ACTIVE_LOW>; + }; + button@1 { + label = "Rear button"; + linux,code = ; + gpios = <&pca9555 15 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&i2c0 { + status = "okay"; + rtc@6f { + compatible = "intersil,isl1208"; + reg = <0x6f>; + }; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + gpio-base = <0>; + }; + + /* CPU core temp sensor and VDD (1.0V) sensor */ + ltc2990@4c { + compatible = "lltc,ltc2990"; + reg = <0x4C>; + lltc,meas-mode = <4 3>; + }; + + /* 3.3V and 5V monitor (may not be loaded on some SKUs) */ + ltc2990@4f { + compatible = "lltc,ltc2990"; + reg = <0x4F>; + lltc,meas-mode = <6 3>; + }; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + /* Only NAND flash is used on this board */ + ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>; + + nand@1,0 { + compatible = "fsl,ifc-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x10000>; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; + +#include "fsl-ls1043-post.dtsi" + +&fman0 { + EMAC0: ethernet@e0000 { + phy-handle = <&qsgmii_phy1>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 01]; + }; + + EMAC1: ethernet@e2000 { + phy-handle = <&qsgmii_phy2>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 02]; + }; + + EMAC2: ethernet@e8000 { + phy-handle = <&qsgmii_phy3>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 03]; + }; + + EMAC3: ethernet@ea000 { + phy-handle = <&qsgmii_phy4>; + phy-connection-type = "qsgmii"; + local-mac-address = [0A 00 00 00 00 04]; + }; + EMAC4: ethernet@e4000 { + phy-handle = <&rgmii_phy1>; + phy-connection-type = "rgmii"; + local-mac-address = [0A 00 00 00 00 05]; + }; + + /* Connection to VDSL SoC */ + EMAC5: ethernet@e6000 { + phy-connection-type = "rgmii-id"; + local-mac-address = [00 00 00 00 00 06]; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + /* 10G XFI interface - not in use on this platform */ + TENSFP: ethernet@f0000 { + status = "disabled"; + + phy-connection-type = "sgmii"; + fixed-link { + /* NB: speed = 1000 and sgmii allows forward compatibility + * with both 1G and 10G, the same is not true + * in the reverse. + */ + speed = <1000>; + full-duplex; + }; + }; + + mdio@fc000 { + rgmii_phy1: ethernet-phy@3 { + reg = <0x3>; + }; + qsgmii_phy1: ethernet-phy@4 { + reg = <0x4>; + }; + qsgmii_phy2: ethernet-phy@5 { + reg = <0x5>; + }; + qsgmii_phy3: ethernet-phy@6 { + reg = <0x6>; + }; + qsgmii_phy4: ethernet-phy@7 { + reg = <0x7>; + }; + }; +}; + +/* No QUICC engine functions on this board */ +&uqe { + status = "disabled"; +}; + +/* No SATA/AHCI on this board */ +&sata { + status = "disabled"; +}; diff --git a/target/linux/layerscape/image/Makefile b/target/linux/layerscape/image/Makefile index fc76ddd2ef..8e1e847f59 100644 --- a/target/linux/layerscape/image/Makefile +++ b/target/linux/layerscape/image/Makefile @@ -7,6 +7,8 @@ include $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/image.mk +ITB_BOARDS = traverse-five64 + define Build/append-ls-rcw rm -f $@ dd if=$(STAGING_DIR_IMAGE)/$(1)-rcw.bin >> $@ @@ -45,6 +47,16 @@ define Build/append-ls-dtb dd if=$(DTS_DIR)/$(1).dtb >> $@ endef +define Build/traverse-fit + ./mkits-multiple-config.sh -o $@.its -A $(LINUX_KARCH) -v $(LINUX_VERSION) \ + -k $@ -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \ + -C gzip -c 1 -c 2 \ + -d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043s.dtb -D "Traverse_LS1043S" -n "ls1043s" -a $(FDT_LOADADDR) -c 1 \ + -d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043v.dtb -D "Traverse_LS1043V" -n "ls1043v" -a $(FDT_LOADADDR) -c 2 + PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new + @mv -f $@.new $@ +endef + define Device/Default PROFILES = Default FILESYSTEMS := squashfs @@ -62,6 +74,7 @@ ifeq ($(SUBTARGET),armv8_32b) KERNEL_LOADADDR = 0x80008000 KERNEL_ENTRY_POINT = 0x80008000 endif + FDT_LOADADDR = 0x90000000 endef define Device/ls1043ardb @@ -182,4 +195,28 @@ endef TARGET_DEVICES += ls2088ardb endif +define Device/traverse-five64 + KERNEL_NAME := Image + KERNEL_SUFFIX := -kernel.itb + KERNEL_INSTALL := 1 + FILESYSTEMS := ubifs + DEVICE_TITLE := Traverse LS1043 Boards (Five64, LS1043S) + DEVICE_PACKAGES += fman-layerscape-ls1043ardb kmod-i2c-core kmod-rtc-isl1208 uboot-envtools \ + uboot-traverse-ls1043v uboot-traverse-ls1043v-sdcard \ + kmod-hwmon-core kmod-hwmon-ltc2990 kmod-gpio-pca953x kmod-input-gpio-keys-polled \ + kmod-i2c-mux-pca954x kmod-hwmon-pac1934 kmod-hwmon-emc17xx + DEVICE_DESCRIPTION = Build images for Traverse LS1043 boards. This generates a single image \ + capable of booting on any of the boards in this family. + DEVICE_DTS = freescale/traverse-ls1043s + DEVICE_DTS_DIR = $(LINUX_DIR)/arch/arm64/boot/dts + DEVICE_DTS_CONFIG = ls1043s + KERNEL := kernel-bin | gzip | traverse-fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FDT_LOADADDR) + KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FDT_LOADADDR) + IMAGES = root sysupgrade.tar + IMAGE/root = append-rootfs + IMAGE/sysupgrade.tar = sysupgrade-tar + UBIFS_OPTS := -m 2048 -e 124KiB -c 4096 +endef +TARGET_DEVICES += traverse-five64 + $(eval $(call BuildImage)) diff --git a/target/linux/layerscape/patches-4.9/304-dts-layerscape-add-traverse-ls1043.patch b/target/linux/layerscape/patches-4.9/304-dts-layerscape-add-traverse-ls1043.patch new file mode 100644 index 0000000000..6c1c28f400 --- /dev/null +++ b/target/linux/layerscape/patches-4.9/304-dts-layerscape-add-traverse-ls1043.patch @@ -0,0 +1,89 @@ +From c0612164b379ebc8964da6bc6f6ced9736dce488 Mon Sep 17 00:00:00 2001 +From: Mathew McBride +Date: Tue, 17 Apr 2018 10:01:03 +1000 +Subject: [PATCH] add DTS for Traverse LS1043 Boards + +Signed-off-by: Mathew McBride +--- + arch/arm64/boot/dts/freescale/Makefile | 5 ++++- + 1 file changed, 4 insertions(+), 1 deletion(-) + create mode 100644 arch/arm64/boot/dts/freescale/traverse-ls1043v.dts + +--- a/arch/arm64/boot/dts/freescale/Makefile ++++ b/arch/arm64/boot/dts/freescale/Makefile +@@ -20,7 +20,10 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2 + dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb + dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb + dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb +- ++ ++dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043v.dtb ++dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043s.dtb ++ + always := $(dtb-y) + subdir-y := $(dts-dirs) + clean-files := *.dtb +--- a/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts ++++ b/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts +@@ -337,3 +337,29 @@ + &sata { + status = "disabled"; + }; ++ ++/* Additions for Layerscape SDK (4.4/4.9) Kernel only ++ * These kernels need additional setup for FMan/QMan DMA shared memory ++ */ ++ ++&bman_fbpr { ++ compatible = "fsl,bman-fbpr"; ++ alloc-ranges = <0 0 0x10000 0>; ++}; ++&qman_fqd { ++ compatible = "fsl,qman-fqd"; ++ alloc-ranges = <0 0 0x10000 0>; ++}; ++&qman_pfdr { ++ compatible = "fsl,qman-pfdr"; ++ alloc-ranges = <0 0 0x10000 0>; ++}; ++ ++&soc { ++#include "qoriq-dpaa-eth.dtsi" ++#include "qoriq-fman3-0-6oh.dtsi" ++}; ++ ++&fman0 { ++ compatible = "fsl,fman", "simple-bus"; ++}; +--- a/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts ++++ b/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts +@@ -313,3 +313,29 @@ + &sata { + status = "disabled"; + }; ++ ++/* Additions for Layerscape SDK (4.4/4.9) Kernel only ++ * These kernels need additional setup for FMan/QMan DMA shared memory ++ */ ++ ++&bman_fbpr { ++ compatible = "fsl,bman-fbpr"; ++ alloc-ranges = <0 0 0x10000 0>; ++}; ++&qman_fqd { ++ compatible = "fsl,qman-fqd"; ++ alloc-ranges = <0 0 0x10000 0>; ++}; ++&qman_pfdr { ++ compatible = "fsl,qman-pfdr"; ++ alloc-ranges = <0 0 0x10000 0>; ++}; ++ ++&soc { ++#include "qoriq-dpaa-eth.dtsi" ++#include "qoriq-fman3-0-6oh.dtsi" ++}; ++ ++&fman0 { ++ compatible = "fsl,fman", "simple-bus"; ++}; diff --git a/target/linux/layerscape/patches-4.9/820-rgmii-fixed-link.patch b/target/linux/layerscape/patches-4.9/820-rgmii-fixed-link.patch index b867b1805a..593bd3e79a 100644 --- a/target/linux/layerscape/patches-4.9/820-rgmii-fixed-link.patch +++ b/target/linux/layerscape/patches-4.9/820-rgmii-fixed-link.patch @@ -5,8 +5,8 @@ Subject: [PATCH] Recognize when an RGMII Link is set as fixed (in the device tree) and set up the MAC accordingly --- - drivers/net/ethernet/freescale/sdk_dpaa/mac.c | 1 + - .../ethernet/freescale/sdk_fman/Peripherals/FM/MAC/memac.c | 13 +++++++++++++ + drivers/net/ethernet/freescale/sdk_dpaa/mac.c | 1 + drivers/net/ethernet/freescale/sdk_fman/Peripherals/FM/MAC/memac.c | 13 ++++++++++ 2 files changed, 14 insertions(+) --- a/drivers/net/ethernet/freescale/sdk_dpaa/mac.c @@ -43,19 +43,19 @@ Subject: [PATCH] Recognize when an RGMII Link is set as fixed (in the device { t_Memac *p_Memac = (t_Memac *)h_Memac; -+ struct mac_device *mac_dev = (struct mac_device *)p_Memac->h_App; ++ struct mac_device *mac_dev = (struct mac_device *)p_Memac->h_App; + SANITY_CHECK_RETURN_ERROR(p_Memac, E_INVALID_HANDLE); SANITY_CHECK_RETURN_ERROR(!p_Memac->p_MemacDriverParam, E_INVALID_STATE); fman_memac_enable(p_Memac->p_MemMap, (mode & e_COMM_MODE_RX), (mode & e_COMM_MODE_TX)); -+ if (ENET_INTERFACE_FROM_MODE(p_Memac->enetMode) == e_ENET_IF_RGMII) { -+ if (mac_dev->fixed_link) { -+ printk("This is a fixed-link, forcing speed %d duplex %d\n",mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex); -+ MemacAdjustLink(h_Memac,mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex); -+ } ++ if (ENET_INTERFACE_FROM_MODE(p_Memac->enetMode) == e_ENET_IF_RGMII) { ++ if (mac_dev->fixed_link) { ++ printk(KERN_INFO "This is a fixed-link, forcing speed %d duplex %d\n",mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex); ++ MemacAdjustLink(h_Memac,mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex); + } ++ } + return E_OK; } diff --git a/target/linux/layerscape/patches-4.9/821-add-esdhc-vsel-to-ls1043.patch b/target/linux/layerscape/patches-4.9/821-add-esdhc-vsel-to-ls1043.patch new file mode 100644 index 0000000000..c45c6b4a22 --- /dev/null +++ b/target/linux/layerscape/patches-4.9/821-add-esdhc-vsel-to-ls1043.patch @@ -0,0 +1,10 @@ +--- a/drivers/mmc/host/sdhci-of-esdhc.c ++++ b/drivers/mmc/host/sdhci-of-esdhc.c +@@ -619,6 +619,7 @@ static void esdhc_reset(struct sdhci_hos + static const struct of_device_id scfg_device_ids[] = { + { .compatible = "fsl,t1040-scfg", }, + { .compatible = "fsl,ls1012a-scfg", }, ++ { .compatible = "fsl,ls1043a-scfg", }, + { .compatible = "fsl,ls1046a-scfg", }, + {} + };