sbc8349: combine HRCW flash and u-boot image flash

Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x.  One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.

This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

diff --git a/board/sbc8349/config.mk b/board/sbc8349/config.mk
index 05fa5a07d571ffefb76d917cb2d3847a9999e08a..eacb27eec2aaac41ee6c740d5e96125b2d1e19b9 100644 (file)
--- a/board/sbc8349/config.mk
+++ b/board/sbc8349/config.mk
@@ -24,4 +24,4 @@
 # SBC8349E
 #
 
-TEXT_BASE  =   0xFFF00000
+TEXT_BASE  =   0xFF800000

diff --git a/doc/README.sbc8349 b/doc/README.sbc8349
index a0ac6388d6060e8653212304ae0e83843a68cdd4..908e7680a6be02ac9fa40e4754cc8a978037830b 100644 (file)
--- a/doc/README.sbc8349
+++ b/doc/README.sbc8349
@@ -21,15 +21,22 @@ Flash Details:
 
 The flash type is intel 28F640Jx (4096x16) [one device].  Base address
 is 0xFF80_0000 which is also where the Hardware Reset Configuration
-Word (HRCW) is stored.  Caution should be used to not overwrite the
-HRCW, or "CF RCW" with a Wind River ICE will be required to restore
-the HRCW and allow the board to enter background mode for further
-steps in the flash process.
+Word (HRCW) is stored.  Caution should be used to not reset the
+board without having a valid HRCW in place (i.e. erased flash) as
+then a Wind River ICE will be required to restore the HRCW and flash
+image.
 
 
 Restoring a corrupted or missing flash image:
 =============================================
 
+Note that U-boot versions up to and including 2009.06 had essentially
+two copies of u-boot in flash; one at the very beginning, which set
+the HRCW, and one at the very end, which was the image that was run.
+As of this point in time, the two have been combined into just one
+at the beginning of flash, which provides both the HRCW, and the image
+that is executed.  This frees up the remainder of flash for other uses.
+Use of the u-boot command "fli" will indicate what parts are in use.
 Details for storing U-boot to flash using a Wind River ICE can be found
 on page 19 of the board manual (request ERG-00328-001).  The following
 is a summary of that information:
@@ -39,9 +46,9 @@ is a summary of that information:
   - Select the appropriate flash type (listed above)
   - Prepare a u-boot image by using the Wind River Convert utility;
     by using "Convert and Add file" on the ELF file from your build.
-    Convert from FFF0_0000 to FFFF_FFFF (or to FFF3_FFFF if you are
-    trying to preserve your old environment settings).
-  - Set the start address of the erase/flash process to FFF0_0000
+    Convert from FF80_0000 to FFFF_FFFF (or to FF83_FFFF if you are
+    trying to preserve your old environment settings and user flash).
+  - Set the start address of the erase/flash process to FF80_0000
   - Set the target RAM required to 64kB.
   - Select sectors for erasing (see note on enviroment below)
   - Select Erase and Reprogram.
@@ -59,7 +66,7 @@ beginning with "SCGA TSEC1" and "SCGA TSEC2".  This allows you to
 use all the remaining register file content.
 
 If you wish to preserve your prior U-Boot environment settings,
-then convert (and erase to) 0xFFF3FFFF instead of 0xFFFFFFFF.
+then convert (and erase to) 0xFF83FFFF instead of 0xFFFFFFFF.
 The size for converting (and erasing) must be at least as large
 as u-boot.bin.
 
@@ -73,10 +80,13 @@ has been copied to the TFTP server, the commands are:
 
        tftp 200000 u-boot.bin
        protect off all
-       erase fff00000 fff3ffff
-       cp.b 200000 fff00000 3ffff
+       erase ff800000 ff83ffff
+       cp.b 200000 ff800000 40000
        protect on all
 
+You may wish to do a "md ff800000 20" operation as a prefix and postfix
+to the above steps to inspect/compare the HRCW before/after as an extra
+safety check before resetting the board upon completion of the reflash.
 
 PCI:
 ====

diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 84a251a06aa8a6d8b0364b78adb05eafde5547ce..868bd54a6a3defaeea627d726178353d755d7b0e 100644 (file)
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -651,8 +651,8 @@
        "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
                "bootm\0"                                               \
        "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0"               \
-       "update=protect off fff00000 fff3ffff; "                        \
-               "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0"     \
+       "update=protect off ff800000 ff83ffff; "                        \
+               "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0"     \
        "upd=run load update\0"                                         \
        "fdtaddr=400000\0"                                              \
        "fdtfile=sbc8349.dtb\0"                                         \