This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
config TARGET_A4M072
bool "Support a4m072"
-config TARGET_BC3450
- bool "Support BC3450"
-
config TARGET_CANMB
bool "Support canmb"
source "board/a3m071/Kconfig"
source "board/a4m072/Kconfig"
-source "board/bc3450/Kconfig"
source "board/canmb/Kconfig"
source "board/cm5200/Kconfig"
source "board/galaxy5200/Kconfig"
+++ /dev/null
-if TARGET_BC3450
-
-config SYS_BOARD
- default "bc3450"
-
-config SYS_CONFIG_NAME
- default "BC3450"
-
-endif
+++ /dev/null
-BC3450 BOARD
-#M: -
-S: Maintained
-F: board/bc3450/
-F: include/configs/BC3450.h
-F: configs/BC3450_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := bc3450.o cmd_bc3450.o
+++ /dev/null
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * (C) Copyright 2004-2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * (C) Copyright 2006
- * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <netdev.h>
-
-#ifdef CONFIG_VIDEO_SM501
-#include <sm501.h>
-#endif
-
-#if defined(CONFIG_MPC5200_DDR)
-#include "mt46v16m16-75.h"
-#else
-#include "mt48lc16m16a2-75.h"
-#endif
-
-#ifdef CONFIG_RTC_MPC5200
-#include <rtc.h>
-#endif
-
-#ifdef CONFIG_PS2MULT
-void ps2mult_early_init(void);
-#endif
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start (int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 |
- hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
- hi_addr_bit;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set mode register: extended mode */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-#endif
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
- hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
- hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram (int board_type)
-{
- ulong dramsize = 0;
- ulong dramsize2 = 0;
-#ifndef CONFIG_SYS_RAMBOOT
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001c; /* 512MB at 0x0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x40000000; /* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set tap delay */
- *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-#endif
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
- sdram_start(1);
- test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20)) {
- dramsize = 0;
- }
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
- __builtin_ffs(dramsize >> 20) - 1;
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- }
-
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001c; /* 512MB */
-
- /* find RAM size using SDRAM CS1 only */
- sdram_start(0);
- test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x20000000);
- sdram_start(1);
- test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x20000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize2 = test1;
- } else {
- dramsize2 = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize2 < (1 << 20)) {
- dramsize2 = 0;
- }
-
- /* set SDRAM CS1 size according to the amount of RAM found */
- if (dramsize2 > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
- | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
- }
-
-#else /* CONFIG_SYS_RAMBOOT */
-
- /* retrieve size of memory connected to SDRAM CS0 */
- dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
- if (dramsize >= 0x13) {
- dramsize = (1 << (dramsize - 0x13)) << 20;
- } else {
- dramsize = 0;
- }
-
- /* retrieve size of memory connected to SDRAM CS1 */
- dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
- if (dramsize2 >= 0x13) {
- dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
- } else {
- dramsize2 = 0;
- }
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- return dramsize;
-}
-
-int checkboard (void)
-{
-#if defined (CONFIG_TQM5200)
- puts ("Board: TQM5200 (TQ-Components GmbH)\n");
-#endif
-
-#if defined (CONFIG_BC3450)
- puts ("Dev: GERSYS BC3450\n");
-#endif
-
- return 0;
-}
-
-void flash_preinit(void)
-{
- /*
- * Now, when we are in RAM, enable flash write
- * access for detection process.
- * Note that CS_BOOT cannot be cleared when
- * executing in flash.
- */
- *(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-}
-
-
-#ifdef CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
- debug ("init_ide_reset\n");
-
- /* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
-}
-
-void ide_set_reset (int idereset)
-{
- debug ("ide_reset(%d)\n", idereset);
-
- if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
- } else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
- }
-}
-#endif
-
-#ifdef CONFIG_POST
-/*
- * Reads GPIO pin PSC6_3. A keypress is reported, if PSC6_3 is low. If PSC6_3
- * is left open, no keypress is detected.
- */
-int post_hotkeys_pressed(void)
-{
- struct mpc5xxx_gpio *gpio;
-
- gpio = (struct mpc5xxx_gpio*) MPC5XXX_GPIO;
-
- /*
- * Configure PSC6_1 and PSC6_3 as GPIO. PSC6 then couldn't be used in
- * CODEC or UART mode. Consumer IrDA should still be possible.
- */
- gpio->port_config &= ~(0x07000000);
- gpio->port_config |= 0x03000000;
-
- /* Enable GPIO for GPIO_IRDA_1 (IR_USB_CLK pin) = PSC6_3 */
- gpio->simple_gpioe |= 0x20000000;
-
- /* Configure GPIO_IRDA_1 as input */
- gpio->simple_ddr &= ~(0x20000000);
-
- return ((gpio->simple_ival & 0x20000000) ? 0 : 1);
-}
-#endif
-
-#ifdef CONFIG_BOARD_EARLY_INIT_R
-int board_early_init_r (void)
-{
-#ifdef CONFIG_RTC_MPC5200
- struct rtc_time t;
-
- /* set to Wed Dec 31 19:00:00 1969 */
- t.tm_sec = t.tm_min = 0;
- t.tm_hour = 19;
- t.tm_mday = 31;
- t.tm_mon = 12;
- t.tm_year = 1969;
- t.tm_wday = 3;
-
- rtc_set(&t);
-#endif /* CONFIG_RTC_MPC5200 */
-
-#ifdef CONFIG_PS2MULT
- ps2mult_early_init();
-#endif /* CONFIG_PS2MULT */
- return (0);
-}
-#endif /* CONFIG_BOARD_EARLY_INIT_R */
-
-
-int last_stage_init (void)
-{
- /*
- * auto scan for really existing devices and re-set chip select
- * configuration.
- */
- u16 save, tmp;
- int restore;
-
- /*
- * Check for SRAM and SRAM size
- */
-
- /* save original SRAM content */
- save = *(volatile u16 *)CONFIG_SYS_CS2_START;
- restore = 1;
-
- /* write test pattern to SRAM */
- *(volatile u16 *)CONFIG_SYS_CS2_START = 0xA5A5;
- __asm__ volatile ("sync");
- /*
- * Put a different pattern on the data lines: otherwise they may float
- * long enough to read back what we wrote.
- */
- tmp = *(volatile u16 *)CONFIG_SYS_FLASH_BASE;
- if (tmp == 0xA5A5)
- puts ("!! possible error in SRAM detection\n");
-
- if (*(volatile u16 *)CONFIG_SYS_CS2_START != 0xA5A5) {
- /* no SRAM at all, disable cs */
- *(vu_long *)MPC5XXX_ADDECR &= ~(1 << 18);
- *(vu_long *)MPC5XXX_CS2_START = 0x0000FFFF;
- *(vu_long *)MPC5XXX_CS2_STOP = 0x0000FFFF;
- restore = 0;
- __asm__ volatile ("sync");
- } else if (*(volatile u16 *)(CONFIG_SYS_CS2_START + (1<<19)) == 0xA5A5) {
- /* make sure that we access a mirrored address */
- *(volatile u16 *)CONFIG_SYS_CS2_START = 0x1111;
- __asm__ volatile ("sync");
- if (*(volatile u16 *)(CONFIG_SYS_CS2_START + (1<<19)) == 0x1111) {
- /* SRAM size = 512 kByte */
- *(vu_long *)MPC5XXX_CS2_STOP = STOP_REG(CONFIG_SYS_CS2_START,
- 0x80000);
- __asm__ volatile ("sync");
- puts ("SRAM: 512 kB\n");
- }
- else
- puts ("!! possible error in SRAM detection\n");
- } else {
- puts ("SRAM: 1 MB\n");
- }
- /* restore origianl SRAM content */
- if (restore) {
- *(volatile u16 *)CONFIG_SYS_CS2_START = save;
- __asm__ volatile ("sync");
- }
-
- /*
- * Check for Grafic Controller
- */
-
- /* save origianl FB content */
- save = *(volatile u16 *)CONFIG_SYS_CS1_START;
- restore = 1;
-
- /* write test pattern to FB memory */
- *(volatile u16 *)CONFIG_SYS_CS1_START = 0xA5A5;
- __asm__ volatile ("sync");
- /*
- * Put a different pattern on the data lines: otherwise they may float
- * long enough to read back what we wrote.
- */
- tmp = *(volatile u16 *)CONFIG_SYS_FLASH_BASE;
- if (tmp == 0xA5A5)
- puts ("!! possible error in grafic controller detection\n");
-
- if (*(volatile u16 *)CONFIG_SYS_CS1_START != 0xA5A5) {
- /* no grafic controller at all, disable cs */
- *(vu_long *)MPC5XXX_ADDECR &= ~(1 << 17);
- *(vu_long *)MPC5XXX_CS1_START = 0x0000FFFF;
- *(vu_long *)MPC5XXX_CS1_STOP = 0x0000FFFF;
- restore = 0;
- __asm__ volatile ("sync");
- } else {
- puts ("VGA: SMI501 (Voyager) with 8 MB\n");
- }
- /* restore origianl FB content */
- if (restore) {
- *(volatile u16 *)CONFIG_SYS_CS1_START = save;
- __asm__ volatile ("sync");
- }
-
- return 0;
-}
-
-#ifdef CONFIG_VIDEO_SM501
-
-#define DISPLAY_WIDTH 640
-#define DISPLAY_HEIGHT 480
-
-#ifdef CONFIG_VIDEO_SM501_8BPP
-#error CONFIG_VIDEO_SM501_8BPP not supported.
-#endif /* CONFIG_VIDEO_SM501_8BPP */
-
-#ifdef CONFIG_VIDEO_SM501_16BPP
-#error CONFIG_VIDEO_SM501_16BPP not supported.
-#endif /* CONFIG_VIDEO_SM501_16BPP */
-
-#ifdef CONFIG_VIDEO_SM501_32BPP
-static const SMI_REGS init_regs [] =
-{
-#if defined (CONFIG_BC3450_FP) && !defined (CONFIG_BC3450_CRT)
- /* FP only */
- {0x00004, 0x0},
- {0x00048, 0x00021807},
- {0x0004C, 0x091a0a01},
- {0x00054, 0x1},
- {0x00040, 0x00021807},
- {0x00044, 0x091a0a01},
- {0x00054, 0x0},
- {0x80000, 0x01013106},
- {0x80004, 0xc428bb17},
- {0x80000, 0x03013106},
- {0x8000C, 0x00000000},
- {0x80010, 0x0a000a00},
- {0x80014, 0x02800000},
- {0x80018, 0x01e00000},
- {0x8001C, 0x00000000},
- {0x80020, 0x01e00280},
- {0x80024, 0x02fa027f},
- {0x80028, 0x004a028b},
- {0x8002C, 0x020c01df},
- {0x80030, 0x000201e9},
- {0x80200, 0x00010200},
- {0x80000, 0x0f013106},
-#elif defined (CONFIG_BC3450_CRT) && !defined (CONFIG_BC3450_FP)
- /* CRT only */
- {0x00004, 0x0},
- {0x00048, 0x00021807},
- {0x0004C, 0x10090a01},
- {0x00054, 0x1},
- {0x00040, 0x00021807},
- {0x00044, 0x10090a01},
- {0x00054, 0x0},
- {0x80200, 0x00010000},
- {0x80204, 0x0},
- {0x80208, 0x0A000A00},
- {0x8020C, 0x02fa027f},
- {0x80210, 0x004a028b},
- {0x80214, 0x020c01df},
- {0x80218, 0x000201e9},
- {0x80200, 0x00013306},
-#else /* panel + CRT */
- {0x00004, 0x0},
- {0x00048, 0x00021807},
- {0x0004C, 0x091a0a01},
- {0x00054, 0x1},
- {0x00040, 0x00021807},
- {0x00044, 0x091a0a01},
- {0x00054, 0x0},
- {0x80000, 0x0f013106},
- {0x80004, 0xc428bb17},
- {0x8000C, 0x00000000},
- {0x80010, 0x0a000a00},
- {0x80014, 0x02800000},
- {0x80018, 0x01e00000},
- {0x8001C, 0x00000000},
- {0x80020, 0x01e00280},
- {0x80024, 0x02fa027f},
- {0x80028, 0x004a028b},
- {0x8002C, 0x020c01df},
- {0x80030, 0x000201e9},
- {0x80200, 0x00010000},
-#endif
- {0, 0}
-};
-#endif /* CONFIG_VIDEO_SM501_32BPP */
-
-#ifdef CONFIG_CONSOLE_EXTRA_INFO
-/*
- * Return text to be printed besides the logo.
- */
-void video_get_info_str (int line_number, char *info)
-{
- if (line_number == 1) {
-#if defined (CONFIG_TQM5200)
- strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
-#else
-#error No supported board selected
-#endif /* CONFIG_TQM5200 */
-
-#if defined (CONFIG_BC3450)
- } else if (line_number == 2) {
- strcpy (info, " Dev: GERSYS BC3450");
-#endif /* CONFIG_BC3450 */
- }
- else {
- info [0] = '\0';
- }
-}
-#endif
-
-/*
- * Returns SM501 register base address. First thing called in the
- * driver. Checks if SM501 is physically present.
- */
-unsigned int board_video_init (void)
-{
- u16 save, tmp;
- int restore, ret;
-
- /*
- * Check for Grafic Controller
- */
-
- /* save origianl FB content */
- save = *(volatile u16 *)CONFIG_SYS_CS1_START;
- restore = 1;
-
- /* write test pattern to FB memory */
- *(volatile u16 *)CONFIG_SYS_CS1_START = 0xA5A5;
- __asm__ volatile ("sync");
- /*
- * Put a different pattern on the data lines: otherwise they may float
- * long enough to read back what we wrote.
- */
- tmp = *(volatile u16 *)CONFIG_SYS_FLASH_BASE;
- if (tmp == 0xA5A5)
- puts ("!! possible error in grafic controller detection\n");
-
- if (*(volatile u16 *)CONFIG_SYS_CS1_START != 0xA5A5) {
- /* no grafic controller found */
- restore = 0;
- ret = 0;
- } else {
- ret = SM501_MMIO_BASE;
- }
-
- if (restore) {
- *(volatile u16 *)CONFIG_SYS_CS1_START = save;
- __asm__ volatile ("sync");
- }
- return ret;
-}
-
-/*
- * Returns SM501 framebuffer address
- */
-unsigned int board_video_get_fb (void)
-{
- return SM501_FB_BASE;
-}
-
-/*
- * Called after initializing the SM501 and before clearing the screen.
- */
-void board_validate_screen (unsigned int base)
-{
-}
-
-/*
- * Return a pointer to the initialization sequence.
- */
-const SMI_REGS *board_get_regs (void)
-{
- return init_regs;
-}
-
-int board_get_width (void)
-{
- return DISPLAY_WIDTH;
-}
-
-int board_get_height (void)
-{
- return DISPLAY_HEIGHT;
-}
-
-#endif /* CONFIG_VIDEO_SM501 */
-
-int board_eth_init(bd_t *bis)
-{
- cpu_eth_init(bis); /* Built in FEC comes first */
- return pci_eth_init(bis);
-}
+++ /dev/null
-/*
- * (C) Copyright 2005
- * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de
- *
- * (C) Copyright 2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-
-/*
- * BC3450 specific commands
- */
-#if defined(CONFIG_CMD_BSP)
-
-/*
- * Definitions for DS1620 chip
- */
-#define THERM_START_CONVERT 0xee
-#define THERM_RESET 0xaf
-#define THERM_READ_CONFIG 0xac
-#define THERM_READ_TEMP 0xaa
-#define THERM_READ_TL 0xa2
-#define THERM_READ_TH 0xa1
-#define THERM_WRITE_CONFIG 0x0c
-#define THERM_WRITE_TL 0x02
-#define THERM_WRITE_TH 0x01
-
-#define CONFIG_SYS_1SHOT 1
-#define CONFIG_SYS_STANDALONE 0
-
-struct therm {
- int hi;
- int lo;
-};
-
-/*
- * SM501 Register
- */
-#define SM501_GPIO_CTRL_LOW 0x00000008UL /* gpio pins 0..31 */
-#define SM501_GPIO_CTRL_HIGH 0x0000000CUL /* gpio pins 32..63 */
-#define SM501_POWER_MODE0_GATE 0x00000040UL
-#define SM501_POWER_MODE1_GATE 0x00000048UL
-#define POWER_MODE_GATE_GPIO_PWM_I2C 0x00000040UL
-#define SM501_GPIO_DATA_LOW 0x00010000UL
-#define SM501_GPIO_DATA_HIGH 0x00010004UL
-#define SM501_GPIO_DATA_DIR_LOW 0x00010008UL
-#define SM501_GPIO_DATA_DIR_HIGH 0x0001000CUL
-#define SM501_PANEL_DISPLAY_CONTROL 0x00080000UL
-#define SM501_CRT_DISPLAY_CONTROL 0x00080200UL
-
-/* SM501 CRT Display Control Bits */
-#define SM501_CDC_SEL (1 << 9)
-#define SM501_CDC_TE (1 << 8)
-#define SM501_CDC_E (1 << 2)
-
-/* SM501 Panel Display Control Bits */
-#define SM501_PDC_FPEN (1 << 27)
-#define SM501_PDC_BIAS (1 << 26)
-#define SM501_PDC_DATA (1 << 25)
-#define SM501_PDC_VDDEN (1 << 24)
-
-/* SM501 GPIO Data LOW Bits */
-#define SM501_GPIO24 0x01000000
-#define SM501_GPIO25 0x02000000
-#define SM501_GPIO26 0x04000000
-#define SM501_GPIO27 0x08000000
-#define SM501_GPIO28 0x10000000
-#define SM501_GPIO29 0x20000000
-#define SM501_GPIO30 0x40000000
-#define SM501_GPIO31 0x80000000
-
-/* SM501 GPIO Data HIGH Bits */
-#define SM501_GPIO46 0x00004000
-#define SM501_GPIO47 0x00008000
-#define SM501_GPIO48 0x00010000
-#define SM501_GPIO49 0x00020000
-#define SM501_GPIO50 0x00040000
-#define SM501_GPIO51 0x00080000
-
-/* BC3450 GPIOs @ SM501 Data LOW */
-#define DIP (SM501_GPIO24 | SM501_GPIO25 | SM501_GPIO26 | SM501_GPIO27)
-#define DS1620_DQ SM501_GPIO29 /* I/O */
-#define DS1620_CLK SM501_GPIO30 /* High active O/P */
-#define DS1620_RES SM501_GPIO31 /* Low active O/P */
-/* BC3450 GPIOs @ SM501 Data HIGH */
-#define BUZZER SM501_GPIO47 /* Low active O/P */
-#define DS1620_TLOW SM501_GPIO48 /* High active I/P */
-#define PWR_OFF SM501_GPIO49 /* Low active O/P */
-#define FP_DATA_TRI SM501_GPIO50 /* High active O/P */
-
-
-/*
- * Initialise GPIO on SM501
- *
- * This function may be called from several other functions.
- * Yet, the initialisation sequence is executed only the first
- * time the function is called.
- */
-int sm501_gpio_init (void)
-{
- static int init_done = 0;
-
- if (init_done) {
- debug("sm501_gpio_init: nothing to be done.\n");
- return 1;
- }
-
- /* enable SM501 GPIO control (in both power modes) */
- *(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE0_GATE) |=
- POWER_MODE_GATE_GPIO_PWM_I2C;
- *(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE1_GATE) |=
- POWER_MODE_GATE_GPIO_PWM_I2C;
-
- /* set up default O/Ps */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
- ~(DS1620_RES | DS1620_CLK);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_DQ;
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
- ~(FP_DATA_TRI);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |=
- (BUZZER | PWR_OFF);
-
- /* configure directions for SM501 GPIO pins */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_LOW) &= ~(0xFF << 24);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_HIGH) &=
- ~(0x3F << 14);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &=
- ~(DIP | DS1620_DQ);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |=
- (DS1620_RES | DS1620_CLK);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) &=
- ~DS1620_TLOW;
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) |=
- (PWR_OFF | BUZZER | FP_DATA_TRI);
-
- init_done = 1;
- debug("sm501_gpio_init: done.\n");
-
- return 0;
-}
-
-
-/*
- * dip - read Config Inputs
- *
- * read and prints the dip switch
- * and/or external config inputs (4bits) 0...0x0F
- */
-int cmd_dip (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- vu_long rc = 0;
-
- sm501_gpio_init ();
-
- /* read dip switch */
- rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
- rc = ~rc;
- rc &= DIP;
- rc = (int) (rc >> 24);
-
- /* plausibility check */
- if (rc > 0x0F)
- return -1;
-
- printf ("0x%lx\n", rc);
- return 0;
-}
-
-U_BOOT_CMD (dip, 1, 1, cmd_dip,
- "read dip switch and config inputs",
- "\n"
- " - prints the state of the dip switch and/or\n"
- " external configuration inputs as hex value.\n"
- " - \"Config 1\" is the LSB");
-
-
-/*
- * buz - turns Buzzer on/off
- */
-#ifdef CONFIG_BC3450_BUZZER
-static int cmd_buz (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- if (argc != 2) {
- printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
- return 1;
- }
-
- sm501_gpio_init ();
-
- if (strncmp (argv[1], "on", 2) == 0) {
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
- ~(BUZZER);
- return 0;
- } else if (strncmp (argv[1], "off", 3) == 0) {
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |=
- BUZZER;
- return 0;
- }
- printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
- return 1;
-}
-
-U_BOOT_CMD (buz, 2, 1, cmd_buz,
- "turns buzzer on/off",
- "\n" "buz <on/off>\n" " - turns the buzzer on or off");
-#endif /* CONFIG_BC3450_BUZZER */
-
-
-/*
- * fp - front panel commands
- */
-static int cmd_fp (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- sm501_gpio_init ();
-
- if (strncmp (argv[1], "on", 2) == 0) {
- /* turn on VDD first */
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_VDDEN;
- udelay (1000);
- /* then put data on */
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_DATA;
- /* wait some time and enable backlight */
- udelay (1000);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_BIAS;
- udelay (1000);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_FPEN;
- return 0;
- } else if (strncmp (argv[1], "off", 3) == 0) {
- /* turn off the backlight first */
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_FPEN;
- udelay (1000);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_BIAS;
- udelay (200000);
- /* wait some time, then remove data */
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_DATA;
- udelay (1000);
- /* and remove VDD last */
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) &=
- ~SM501_PDC_VDDEN;
- return 0;
- } else if (strncmp (argv[1], "bl", 2) == 0) {
- /* turn on/off backlight only */
- if (strncmp (argv[2], "on", 2) == 0) {
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) |=
- SM501_PDC_BIAS;
- udelay (1000);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) |=
- SM501_PDC_FPEN;
- return 0;
- } else if (strncmp (argv[2], "off", 3) == 0) {
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) &=
- ~SM501_PDC_FPEN;
- udelay (1000);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_PANEL_DISPLAY_CONTROL) &=
- ~SM501_PDC_BIAS;
- return 0;
- }
- }
-#ifdef CONFIG_BC3450_CRT
- else if (strncmp (argv[1], "crt", 3) == 0) {
- /* enables/disables the crt output (debug only) */
- if (strncmp (argv[2], "on", 2) == 0) {
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_CRT_DISPLAY_CONTROL) |=
- (SM501_CDC_TE | SM501_CDC_E);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_CRT_DISPLAY_CONTROL) &=
- ~SM501_CDC_SEL;
- return 0;
- } else if (strncmp (argv[2], "off", 3) == 0) {
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_CRT_DISPLAY_CONTROL) &=
- ~(SM501_CDC_TE | SM501_CDC_E);
- *(vu_long *) (SM501_MMIO_BASE +
- SM501_CRT_DISPLAY_CONTROL) |=
- SM501_CDC_SEL;
- return 0;
- }
- }
-#endif /* CONFIG_BC3450_CRT */
- printf ("Usage:%s\n", cmdtp->help);
- return 1;
-}
-
-U_BOOT_CMD (fp, 3, 1, cmd_fp,
- "front panes access functions",
- "\n"
- "fp bl <on/off>\n"
- " - turns the CCFL backlight of the display on/off\n"
- "fp <on/off>\n" " - turns the whole display on/off"
-#ifdef CONFIG_BC3450_CRT
- "\n"
- "fp crt <on/off>\n"
- " - enables/disables the crt output (debug only)"
-#endif /* CONFIG_BC3450_CRT */
- );
-
-/*
- * temp - DS1620 thermometer
- */
-/* GERSYS BC3450 specific functions */
-static inline void bc_ds1620_set_clk (int clk)
-{
- if (clk)
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |=
- DS1620_CLK;
- else
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
- ~DS1620_CLK;
-}
-
-static inline void bc_ds1620_set_data (int dat)
-{
- if (dat)
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |=
- DS1620_DQ;
- else
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
- ~DS1620_DQ;
-}
-
-static inline int bc_ds1620_get_data (void)
-{
- vu_long rc;
-
- rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
- rc &= DS1620_DQ;
- if (rc != 0)
- rc = 1;
- return (int) rc;
-}
-
-static inline void bc_ds1620_set_data_dir (int dir)
-{
- if (dir) /* in */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &= ~DS1620_DQ;
- else /* out */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |= DS1620_DQ;
-}
-
-static inline void bc_ds1620_set_reset (int res)
-{
- if (res)
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_RES;
- else
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~DS1620_RES;
-}
-
-/* hardware independent functions */
-static void ds1620_send_bits (int nr, int value)
-{
- int i;
-
- for (i = 0; i < nr; i++) {
- bc_ds1620_set_data (value & 1);
- bc_ds1620_set_clk (0);
- udelay (1);
- bc_ds1620_set_clk (1);
- udelay (1);
-
- value >>= 1;
- }
-}
-
-static unsigned int ds1620_recv_bits (int nr)
-{
- unsigned int value = 0, mask = 1;
- int i;
-
- bc_ds1620_set_data (0);
-
- for (i = 0; i < nr; i++) {
- bc_ds1620_set_clk (0);
- udelay (1);
-
- if (bc_ds1620_get_data ())
- value |= mask;
-
- mask <<= 1;
-
- bc_ds1620_set_clk (1);
- udelay (1);
- }
-
- return value;
-}
-
-static void ds1620_out (int cmd, int bits, int value)
-{
- bc_ds1620_set_clk (1);
- bc_ds1620_set_data_dir (0);
-
- bc_ds1620_set_reset (0);
- udelay (1);
- bc_ds1620_set_reset (1);
-
- udelay (1);
-
- ds1620_send_bits (8, cmd);
- if (bits)
- ds1620_send_bits (bits, value);
-
- udelay (1);
-
- /* go stand alone */
- bc_ds1620_set_data_dir (1);
- bc_ds1620_set_reset (0);
- bc_ds1620_set_clk (0);
-
- udelay (10000);
-}
-
-static unsigned int ds1620_in (int cmd, int bits)
-{
- unsigned int value;
-
- bc_ds1620_set_clk (1);
- bc_ds1620_set_data_dir (0);
-
- bc_ds1620_set_reset (0);
- udelay (1);
- bc_ds1620_set_reset (1);
-
- udelay (1);
-
- ds1620_send_bits (8, cmd);
-
- bc_ds1620_set_data_dir (1);
- value = ds1620_recv_bits (bits);
-
- /* go stand alone */
- bc_ds1620_set_data_dir (1);
- bc_ds1620_set_reset (0);
- bc_ds1620_set_clk (0);
-
- return value;
-}
-
-static int cvt_9_to_int (unsigned int val)
-{
- if (val & 0x100)
- val |= 0xfffffe00;
-
- return val;
-}
-
-/* set thermostate thresholds */
-static void ds1620_write_state (struct therm *therm)
-{
- ds1620_out (THERM_WRITE_TL, 9, therm->lo);
- ds1620_out (THERM_WRITE_TH, 9, therm->hi);
- ds1620_out (THERM_START_CONVERT, 0, 0);
-}
-
-static int cmd_temp (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- int i;
- struct therm therm;
-
- sm501_gpio_init ();
-
- /* print temperature */
- if (argc == 1) {
- i = cvt_9_to_int (ds1620_in (THERM_READ_TEMP, 9));
- printf ("%d.%d C\n", i >> 1, i & 1 ? 5 : 0);
- return 0;
- }
-
- /* set to default operation */
- if (strncmp (argv[1], "set", 3) == 0) {
- if (strncmp (argv[2], "default", 3) == 0) {
- therm.hi = +88;
- therm.lo = -20;
- therm.hi <<= 1;
- therm.lo <<= 1;
- ds1620_write_state (&therm);
- ds1620_out (THERM_WRITE_CONFIG, 8, CONFIG_SYS_STANDALONE);
- return 0;
- }
- }
-
- printf ("Usage:%s\n", cmdtp->help);
- return 1;
-}
-
-U_BOOT_CMD (temp, 3, 1, cmd_temp,
- "print current temperature",
- "\n" "temp\n" " - print current temperature");
-
-#ifdef CONFIG_BC3450_CAN
-/*
- * Initialise CAN interface
- *
- * return 1 on CAN initialization failure
- * return 0 if no failure
- */
-int can_init (void)
-{
- static int init_done = 0;
- int i;
- struct mpc5xxx_mscan *can1 =
- (struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0900);
- struct mpc5xxx_mscan *can2 =
- (struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0980);
-
- /* GPIO configuration of the CAN pins is done in BC3450.h */
-
- if (!init_done) {
- /* init CAN 1 */
- can1->canctl1 |= 0x80; /* CAN enable */
- udelay (100);
-
- i = 0;
- can1->canctl0 |= 0x02; /* sleep mode */
- /* wait until sleep mode reached */
- while (!(can1->canctl1 & 0x02)) {
- udelay (10);
- i++;
- if (i == 10) {
- printf ("%s: CAN1 initialize error, "
- "can not enter sleep mode!\n",
- __FUNCTION__);
- return 1;
- }
- }
- i = 0;
- can1->canctl0 = 0x01; /* enter init mode */
- /* wait until init mode reached */
- while (!(can1->canctl1 & 0x01)) {
- udelay (10);
- i++;
- if (i == 10) {
- printf ("%s: CAN1 initialize error, "
- "can not enter init mode!\n",
- __FUNCTION__);
- return 1;
- }
- }
- can1->canctl1 = 0x80;
- can1->canctl1 |= 0x40;
- can1->canbtr0 = 0x0F;
- can1->canbtr1 = 0x7F;
- can1->canidac &= ~(0x30);
- can1->canidar1 = 0x00;
- can1->canidar3 = 0x00;
- can1->canidar5 = 0x00;
- can1->canidar7 = 0x00;
- can1->canidmr0 = 0xFF;
- can1->canidmr1 = 0xFF;
- can1->canidmr2 = 0xFF;
- can1->canidmr3 = 0xFF;
- can1->canidmr4 = 0xFF;
- can1->canidmr5 = 0xFF;
- can1->canidmr6 = 0xFF;
- can1->canidmr7 = 0xFF;
-
- i = 0;
- can1->canctl0 &= ~(0x01); /* leave init mode */
- can1->canctl0 &= ~(0x02);
- /* wait until init and sleep mode left */
- while ((can1->canctl1 & 0x01) || (can1->canctl1 & 0x02)) {
- udelay (10);
- i++;
- if (i == 10) {
- printf ("%s: CAN1 initialize error, "
- "can not leave init/sleep mode!\n",
- __FUNCTION__);
- return 1;
- }
- }
-
- /* init CAN 2 */
- can2->canctl1 |= 0x80; /* CAN enable */
- udelay (100);
-
- i = 0;
- can2->canctl0 |= 0x02; /* sleep mode */
- /* wait until sleep mode reached */
- while (!(can2->canctl1 & 0x02)) {
- udelay (10);
- i++;
- if (i == 10) {
- printf ("%s: CAN2 initialize error, "
- "can not enter sleep mode!\n",
- __FUNCTION__);
- return 1;
- }
- }
- i = 0;
- can2->canctl0 = 0x01; /* enter init mode */
- /* wait until init mode reached */
- while (!(can2->canctl1 & 0x01)) {
- udelay (10);
- i++;
- if (i == 10) {
- printf ("%s: CAN2 initialize error, "
- "can not enter init mode!\n",
- __FUNCTION__);
- return 1;
- }
- }
- can2->canctl1 = 0x80;
- can2->canctl1 |= 0x40;
- can2->canbtr0 = 0x0F;
- can2->canbtr1 = 0x7F;
- can2->canidac &= ~(0x30);
- can2->canidar1 = 0x00;
- can2->canidar3 = 0x00;
- can2->canidar5 = 0x00;
- can2->canidar7 = 0x00;
- can2->canidmr0 = 0xFF;
- can2->canidmr1 = 0xFF;
- can2->canidmr2 = 0xFF;
- can2->canidmr3 = 0xFF;
- can2->canidmr4 = 0xFF;
- can2->canidmr5 = 0xFF;
- can2->canidmr6 = 0xFF;
- can2->canidmr7 = 0xFF;
- can2->canctl0 &= ~(0x01); /* leave init mode */
- can2->canctl0 &= ~(0x02);
-
- i = 0;
- /* wait until init mode left */
- while ((can2->canctl1 & 0x01) || (can2->canctl1 & 0x02)) {
- udelay (10);
- i++;
- if (i == 10) {
- printf ("%s: CAN2 initialize error, "
- "can not leave init/sleep mode!\n",
- __FUNCTION__);
- return 1;
- }
- }
- init_done = 1;
- }
- return 0;
-}
-
-/*
- * Do CAN test
- * by sending message between CAN1 and CAN2
- *
- * return 1 on CAN failure
- * return 0 if no failure
- */
-int do_can (char * const argv[])
-{
- int i;
- struct mpc5xxx_mscan *can1 =
- (struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0900);
- struct mpc5xxx_mscan *can2 =
- (struct mpc5xxx_mscan *) (CONFIG_SYS_MBAR + 0x0980);
-
- /* send a message on CAN1 */
- can1->cantbsel = 0x01;
- can1->cantxfg.idr[0] = 0x55;
- can1->cantxfg.idr[1] = 0x00;
- can1->cantxfg.idr[1] &= ~0x8;
- can1->cantxfg.idr[1] &= ~0x10;
- can1->cantxfg.dsr[0] = 0xCC;
- can1->cantxfg.dlr = 1;
- can1->cantxfg.tbpr = 0;
- can1->cantflg = 0x01;
-
- i = 0;
- while ((can1->cantflg & 0x01) == 0) {
- i++;
- if (i == 10) {
- printf ("%s: CAN1 send timeout, "
- "can not send message!\n", __FUNCTION__);
- return 1;
- }
- udelay (1000);
- }
- udelay (1000);
-
- i = 0;
- while (!(can2->canrflg & 0x01)) {
- i++;
- if (i == 10) {
- printf ("%s: CAN2 receive timeout, "
- "no message received!\n", __FUNCTION__);
- return 1;
- }
- udelay (1000);
- }
-
- if (can2->canrxfg.dsr[0] != 0xCC) {
- printf ("%s: CAN2 receive error, "
- "data mismatch!\n", __FUNCTION__);
- return 1;
- }
-
- /* send a message on CAN2 */
- can2->cantbsel = 0x01;
- can2->cantxfg.idr[0] = 0x55;
- can2->cantxfg.idr[1] = 0x00;
- can2->cantxfg.idr[1] &= ~0x8;
- can2->cantxfg.idr[1] &= ~0x10;
- can2->cantxfg.dsr[0] = 0xCC;
- can2->cantxfg.dlr = 1;
- can2->cantxfg.tbpr = 0;
- can2->cantflg = 0x01;
-
- i = 0;
- while ((can2->cantflg & 0x01) == 0) {
- i++;
- if (i == 10) {
- printf ("%s: CAN2 send error, "
- "can not send message!\n", __FUNCTION__);
- return 1;
- }
- udelay (1000);
- }
- udelay (1000);
-
- i = 0;
- while (!(can1->canrflg & 0x01)) {
- i++;
- if (i == 10) {
- printf ("%s: CAN1 receive timeout, "
- "no message received!\n", __FUNCTION__);
- return 1;
- }
- udelay (1000);
- }
-
- if (can1->canrxfg.dsr[0] != 0xCC) {
- printf ("%s: CAN1 receive error 0x%02x\n",
- __FUNCTION__, (can1->canrxfg.dsr[0]));
- return 1;
- }
-
- return 0;
-}
-#endif /* CONFIG_BC3450_CAN */
-
-/*
- * test - BC3450 HW test routines
- */
-int cmd_test (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-#ifdef CONFIG_BC3450_CAN
- int rcode;
-
- can_init ();
-#endif /* CONFIG_BC3450_CAN */
-
- sm501_gpio_init ();
-
- if (argc != 2) {
- printf ("Usage:%s\n", cmdtp->help);
- return 1;
- }
-
- if (strncmp (argv[1], "unit-off", 8) == 0) {
- printf ("waiting 2 seconds...\n");
- udelay (2000000);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
- ~PWR_OFF;
- return 0;
- }
-#ifdef CONFIG_BC3450_CAN
- else if (strncmp (argv[1], "can", 2) == 0) {
- rcode = do_can (argv);
- if (simple_strtoul (argv[2], NULL, 10) == 2) {
- if (rcode == 0)
- printf ("OK\n");
- else
- printf ("Error\n");
- }
- return rcode;
- }
-#endif /* CONFIG_BC3450_CAN */
-
- printf ("Usage:%s\n", cmdtp->help);
- return 1;
-}
-
-U_BOOT_CMD (test, 2, 1, cmd_test, "unit test routines", "\n"
-#ifdef CONFIG_BC3450_CAN
- "test can\n"
- " - connect CAN1 (X8) with CAN2 (X9) for this test\n"
-#endif /* CONFIG_BC3450_CAN */
- "test unit-off\n"
- " - turns off the BC3450 unit\n"
- " WARNING: Unsaved environment variables will be lost!"
-);
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 0 /* is SDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x00CD0000
-/* #define SDRAM_MODE 0x008D0000 */ /* CAS latency 2 */
-#define SDRAM_CONTROL 0x504F0000
-#define SDRAM_CONFIG1 0xD2322800
-/* #define SDRAM_CONFIG1 0xD2222800 */ /* CAS latency 2 */
-/*#define SDRAM_CONFIG1 0xD7322800 */ /* SDRAM controller bug workaround */
-#define SDRAM_CONFIG2 0x8AD70000
-/*#define SDRAM_CONFIG2 0xDDD70000 */ /* SDRAM controller bug workaround */
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_BC3450=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-hawkboard arm arm926ejs - - Syed Mohammed Khasim <sm.khasim@gmail.com>:Sughosh Ganu <urwithsughosh@gmail.com>
-tnetv107x arm arm1176 - - Chan-Taek Park <c-park@ti.com>
-a320evb arm arm920t - - Po-Yu Chuang <ratbert@faraday-tech.com>
-cm4008 arm arm920t - - Greg Ungerer <greg.ungerer@opengear.com>
-cm41xx arm arm920t - -
-dkb arm arm926ejs - - Lei Wen <leiwen@marvell.com>
-jadecpu arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
+BC3450 powerpc mpc5xxx - -
+hawkboard arm arm926ejs cb957cda 2015-02-24 Syed Mohammed Khasim <sm.khasim@gmail.com>:Sughosh Ganu <urwithsughosh@gmail.com>
+tnetv107x arm arm1176 50b82c4b 2015-02-24 Chan-Taek Park <c-park@ti.com>
+a320evb arm arm920t 29fc6f24 2015-02-24 Po-Yu Chuang <ratbert@faraday-tech.com>
+cm4008 arm arm920t a2f39e83 2015-02-24 Greg Ungerer <greg.ungerer@opengear.com>
+cm41xx arm arm920t a2f39e83 2015-02-24
+dkb arm arm926ejs 346cfba4 2015-02-24 Lei Wen <leiwen@marvell.com>
+jadecpu arm arm926ejs 41fbbbbc 2015-02-24 Matthias Weisser <weisserm@arcor.de>
icecube_5200 powerpc mpc5xxx 37b608a5 2015-01-23 Wolfgang Denk <wd@denx.de>
Lite5200 powerpc mpc5xxx 37b608a5 2015-01-23
cpci5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+++ /dev/null
-/*
- * -- Version 1.1 --
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004-2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * (C) Copyright 2005
- * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de.
- *
- * History:
- * 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
-#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */
-
-#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */
-#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */
-#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */
-#define CONFIG_BC3450_USB 1 /* + USB support */
-# define CONFIG_FAT 1 /* + FAT support */
-# define CONFIG_EXT2 1 /* + EXT2 support */
-#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */
-#undef CONFIG_BC3450_CAN /* + CAN transceiver */
-#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */
-#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */
-#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */
-#define CONFIG_BC3450_FP 1 /* + enable FP O/P */
-#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFC000000 boot low (standard configuration with room for
- * max 64 MByte Flash ROM)
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFC000000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * AT-PS/2 Multiplexer
- */
-#ifdef CONFIG_BC3450_PS2
-# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
-# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
-# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
-# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */
-# define CONFIG_BOARD_EARLY_INIT_R
-#endif /* CONFIG_BC3450_PS2 */
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-# define CONFIG_PCI 1
-# define CONFIG_PCI_PNP 1
-/* #define CONFIG_PCI_SCAN_SHOW 1 */
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-
-/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-
-/*
- * Video console
- */
-# define CONFIG_VIDEO
-# define CONFIG_VIDEO_SM501
-# define CONFIG_VIDEO_SM501_32BPP
-# define CONFIG_CFB_CONSOLE
-# define CONFIG_VIDEO_LOGO
-# define CONFIG_VGA_AS_SINGLE_DEVICE
-# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */
-# define CONFIG_VIDEO_SW_CURSOR
-# define CONFIG_SPLASH_SCREEN
-# define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/*
- * Partitions
- */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/*
- * USB
- */
-#ifdef CONFIG_BC3450_USB
-# define CONFIG_USB_OHCI
-# define CONFIG_USB_STORAGE
-#endif /* CONFIG_BC3450_USB */
-
-/*
- * POST support
- */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_I2C)
-
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#endif /* CONFIG_POST */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_BSP
-
-#ifdef CONFIG_VIDEO
- #define CONFIG_CMD_BMP
-#endif
-
-#ifdef CONFIG_BC3450_IDE
- #define CONFIG_CMD_IDE
-#endif
-
-#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB)
- #ifdef CONFIG_FAT
- #define CONFIG_CMD_FAT
- #endif
-
- #ifdef CONFIG_EXT2
- #define CONFIG_CMD_EXT2
- #endif
-#endif
-
-#ifdef CONFIG_BC3450_USB
- #define CONFIG_CMD_USB
-#endif
-
-#ifdef CONFIG_PCI
- #define CONFIG_CMD_PCI
-#endif
-
-#ifdef CONFIG_POST
- #define CONFIG_CMD_DIAG
-#endif
-
-
-#define CONFIG_TIMESTAMP /* display image timestamps */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */
-# define CONFIG_SYS_LOWBOOT 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo;"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "ipaddr=192.168.1.10\0" \
- "serverip=192.168.1.3\0" \
- "netmask=255.255.255.0\0" \
- "hostname=bc3450\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "kernel_addr=fc0a0000\0" \
- "ramdisk_addr=fc1c0000\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "ideargs=setenv bootargs root=/dev/hda2 ro\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "addcons=setenv bootargs $(bootargs) " \
- "console=ttyS0,$(baudrate) console=tty0\0" \
- "flash_self=run ramargs addip addcons;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile); " \
- "run nfsargs addip addcons; bootm\0" \
- "ide_nfs=run nfsargs addip addcons; " \
- "disk 200000 0:1; bootm\0" \
- "ide_ide=run ideargs addip addcons; " \
- "disk 200000 0:1; bootm\0" \
- "usb_self=run usbload; run ramargs addip addcons; " \
- "bootm 200000 400000\0" \
- "usbload=usb reset; usb scan; usbboot 200000 0:1; " \
- "usbboot 400000 0:2\0" \
- "bootfile=uImage\0" \
- "load=tftp 200000 $(u-boot)\0" \
- "u-boot=u-boot.bin\0" \
- "update=protect off FC000000 FC05FFFF;" \
- "erase FC000000 FC05FFFF;" \
- "cp.b 200000 FC000000 $(filesize);" \
- "protect on FC000000 FC05FFFF\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-/*
- * PCI Bus clocking configuration
- *
- * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
- * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
- */
-#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
-# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
-#endif
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration for I²C EEPROM M24C32
- * M24C64 should work also. For other EEPROMs config should be verified.
- *
- * The TQM5200 module may hold an EEPROM at address 0x50.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231)
-# define CONFIG_RTC_M41T11 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#else
-# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */
-# define CONFIG_BOARD_EARLY_INIT_R
-#endif
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
-
-/* use CFI flash driver if no module variant is spezified */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
-
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
-#else /* CONFIG_SYS_LOWBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
-#endif /* CONFIG_SYS_LOWBOOT */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
- (= chip selects) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/* Dynamic MTD partition support */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM5200-0"
-#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
- "1408k(kernel)," \
- "2m(initrd)," \
- "4m(small-fs)," \
- "16m(big-fs)," \
- "8m(misc)"
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
-#else
-# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-#endif /*CONFIG_POST*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- *
- * Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-#undef CONFIG_MPC5xxx_MII10
-#define CONFIG_PHY_ADDR 0x00
-
-/*
- * GPIO configuration on BC3450
- *
- * PSC1: UART1 (Service-UART) [0x xxxxxxx4]
- * PSC2: UART2 [0x xxxxxx4x]
- * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x]
- * PSC3: USB2 [0x xxxxx1xx]
- * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx]
- * (this has to match
- * CONFIG_USB_CONFIG which is
- * used by usb_ohci.c to set
- * the USB ports)
- * Eth: 10/100Mbit Ethernet [0x xxx0xxxx]
- * (this is reset to '5'
- * in FEC driver: fec.c)
- * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx]
- * ATA/CS: ??? [0x x1xxxxxx]
- * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx]
- * CS1: Use Pin gpio_wkup_6 as second
- * SDRAM chip select (mem_cs1)
- * Timer: CAN2 / SPI
- * I2C: CAN1 / I²C2 [0x bxxxxxxx]
- */
-#ifdef CONFIG_BC3450_AC97
-# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124
-#else /* PSC2=UART2 */
-# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max no of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */
-
-#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */
- /* more extensive mem test */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
-# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
-#else
-# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
-#endif
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-/* automatic configuration of chip selects */
-#ifdef CONFIG_TQM5200
-# define CONFIG_LAST_STAGE_INIT
-#endif /* CONFIG_TQM5200 */
-
-/*
- * SRAM - Do not map below 2 GB in address space, because this area is used
- * for SDRAM autosizing.
- */
-#ifdef CONFIG_TQM5200
-# define CONFIG_SYS_CS2_START 0xE5000000
-# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
-# define CONFIG_SYS_CS2_CFG 0x0004D930
-#endif /* CONFIG_TQM5200 */
-
-/*
- * Grafic controller - Do not map below 2 GB in address space, because this
- * area is used for SDRAM autosizing.
- */
-#ifdef CONFIG_TQM5200
-# define SM501_FB_BASE 0xE0000000
-# define CONFIG_SYS_CS1_START (SM501_FB_BASE)
-# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
-# define CONFIG_SYS_CS1_CFG 0x8F48FF70
-# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
-#endif /* CONFIG_TQM5200 */
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */
- /* flash and SM501 */
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*
- * USB stuff
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */
-
-/*
- * IDE/ATA stuff Supports IDE harddisk
- */
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-#endif /* __CONFIG_H */
projects / oweals / u-boot.git / commitdiff